Professional Documents
Culture Documents
<DESTINATION/MODEL> <M/Y>
SUBJECT : Additional descriptions regarding the front and rear wheel alignment
(As shown below) 13-17
MIRAGE/SPACE STAR(A00A)
GROUP : Gr:33(Front suspention)/Gr:34(Rear suspention) ATTRAGE/MIRAGE G4(A10A)
1. Description :
Please refer to the attached document for the information about the descriptions to be added
in the applicable service manuals. The related points in the front and rear wheel alignment
are as follows :
・Toe-angle(Front and Rear)
・Caster(Front only)
・Kingpin inclination(Front only)
MSB-17EXL33_34-001(17AB017) 1
Attached sheet 1 (1/7)
For overseas market
AUSTRALIA/NEW ZEALAND
Applicable manual Pub. No. Applicable title (INFO ID) Contents
SERVICE SPECIFICATIONS
(M332-00-032-22500-01)
FRONT WHEEL ALIGNMENT CHECK AND Attached sheet 2
ADUTMENT
2014 (M331-00-091-89000-01)
AU900305
MIRAGE (HATCHBACK)
NZ:DRAFT SERVICE SPECIFICATIONS
Workshop Manual
(M341-00-031-32700-01)
REAR WHEEL ALIGNMENT CHECK AND Attached sheet 3
ADUTMENT
(M331-00-091-89000-01)
SERVICE SPECIFICATIONS
(M332-00-032-22500-01)
FRONT WHEEL ALIGNMENT CHECK AND Attached sheet 2
ADUTMENT
2015 (M331-00-091-89000-01)
AU900425
MIRAGE (HATCHBACK)
NZ:DRAFT SERVICE SPECIFICATIONS
Workshop Manual
(M341-00-031-32700-01)
REAR WHEEL ALIGNMENT CHECK AND Attached sheet 3
ADUTMENT
(M331-00-091-89000-01)
SERVICE SPECIFICATIONS
(M332-00-032-22500-01)
FRONT WHEEL ALIGNMENT CHECK AND Attached sheet 2
ADUTMENT
2016 (M331-00-091-89000-01)
AU900539
MIRAGE (HATCHBACK)
NZ:DRAFT SERVICE SPECIFICATIONS
Workshop Manual
(M341-00-031-32700-01)
REAR WHEEL ALIGNMENT CHECK AND Attached sheet 3
ADUTMENT
(M331-00-091-89000-01)
SERVICE SPECIFICATIONS
(M332-00-032-22500-01)
FRONT WHEEL ALIGNMENT CHECK AND Attached sheet 2
ADUTMENT
2017 (M331-00-091-89000-01)
AU900581
MIRAGE (HATCHBACK)
NZ:DRAFT SERVICE SPECIFICATIONS
Workshop Manual
(M341-00-031-32700-01)
REAR WHEEL ALIGNMENT CHECK AND Attached sheet 3
ADUTMENT
(M331-00-091-89000-01)
MSB-17EXL33_34-001(17AB017) 2
Attached sheet 1 (2/7)
SERVICE SPECIFICATIONS
(M332-00-032-22500-01)
FRONT WHEEL ALIGNMENT CHECK AND Attached sheet 4
ADUTMENT
2015 (M331-00-091-89000-01)
AU900435
MIRAGE (SEDAN)
NZ:DRAFT SERVICE SPECIFICATIONS
Workshop Manual
(M341-00-031-32700-01)
REAR WHEEL ALIGNMENT CHECK AND Attached sheet 5
ADUTMENT
(M331-00-091-89000-01)
SERVICE SPECIFICATIONS
(M332-00-032-22500-01)
FRONT WHEEL ALIGNMENT CHECK AND Attached sheet 4
ADUTMENT
2016 (M331-00-091-89000-01)
AU900538
MIRAGE (SEDAN)
NZ:DRAFT SERVICE SPECIFICATIONS
Workshop Manual
(M341-00-031-32700-01)
REAR WHEEL ALIGNMENT CHECK AND Attached sheet 5
ADUTMENT
(M331-00-091-89000-01)
EU
Applicable manual Pub. No. Applicable title (INFO ID) Contents
SERVICE SPECIFICATIONS
(M332-00-032-22500-01)
FRONT WHEEL ALIGNMENT CHECK AND Attached sheet 6
CA0E13E1-CD (ENG) ADUTMENT
2013 CA0F13E1-CD (FRE) (M331-00-091-89000-01)
MIRAGE/SPACE STAR CA0G13E1-CD (GER)
Workshop Manual CA0S13E1-CD (SPA) SERVICE SPECIFICATIONS
CA0I13E1-CD (ITA) (M341-00-031-32700-01)
REAR WHEEL ALIGNMENT CHECK AND Attached sheet 5
ADUTMENT
(M341-01-101-32000-01)
SERVICE SPECIFICATIONS
(M332-00-032-22500-01)
FRONT WHEEL ALIGNMENT Attached sheet 6
CA0E14E1-CD (ENG) CHECK AND ADUTMENT
2014 CA0F14E1-CD (FRE) (M331-00-091-89000-01)
MIRAGE/SPACE STAR CA0G14E1-CD (GER)
Workshop Manual CA0S14E1-CD (SPA) SERVICE SPECIFICATIONS
CA0I14E1-CD (ITA) (M341-00-031-32700-01)
REAR WHEEL ALIGNMENT Attached sheet 5
CHECK AND ADUTMENT
(M341-01-101-32000-01)
MSB-17EXL33_34-001(17AB017) 3
Attached sheet 1 (3/7)
SERVICE SPECIFICATIONS
(M332-00-032-22500-01)
FRONT WHEEL ALIGNMENT CHECK AND Attached sheet 6
CA0E15E1-CD (ENG) ADUTMENT
2015 CA0F15E1-CD (FRE) (M331-00-091-89000-01)
MIRAGE/SPACE STAR CA0G15E1-CD (GER)
CA0S15E1-CD (SPA) SERVICE SPECIFICATIONS
Workshop Manual
CA0I15E1-CD (ITA) (M341-00-031-32700-01)
REAR WHEEL ALIGNMENT CHECK AND Attached sheet 5
ADUTMENT
(M341-01-101-32000-01)
SERVICE SPECIFICATIONS
(M332-00-032-22500-01)
FRONT WHEEL ALIGNMENT CHECK AND Attached sheet 6
CA0E15E2-CD (ENG) ADUTMENT
2015.5 CA0F15E2-CD (FRE) (M331-00-091-89000-01)
MIRAGE/SPACE STAR CA0G15E2-CD (GER)
CA0S15E2-CD (SPA) SERVICE SPECIFICATIONS
Workshop Manual
CA0I15E2-CD (ITA) (M341-00-031-32700-01)
REAR WHEEL ALIGNMENT CHECK AND Attached sheet 5
ADUTMENT
(M341-01-101-32000-01)
SERVICE SPECIFICATIONS
(M332-00-032-22500-01)
FRONT WHEEL ALIGNMENT CHECK AND Attached sheet 6
CA0E16E1-CD (ENG) ADUTMENT
2016 CA0F16E1-CD (FRE)
(M331-00-091-89000-01)
MIRAGE/SPACE STAR CA0G16E1-CD (GER)
CA0S16E1-CD (SPA) SERVICE SPECIFICATIONS
Workshop Manual
CA0I16E1-CD (ITA) (M341-00-031-32700-01)
REAR WHEEL ALIGNMENT CHECK AND Attached sheet 5
ADUTMENT
(M341-01-101-32000-01)
SERVICE SPECIFICATIONS
(M332-00-032-31100-01)
FRONT WHEEL ALIGNMENT Attached sheet 4
CHECK AND ADUTMENT
2014 CA1E14E1-CD (ENG) (M331-00-091-96400-01)
ATTRAGE CA1F14E1-CD (FRE)
Workshop Manual CA1G14E1-CD (GER) SERVICE SPECIFICATIONS
(M341-00-031-32700-01)
REAR WHEEL ALIGNMENT Attached sheet 5
CHECK AND ADUTMENT
(M341-01-101-32000-01)
MSB-17EXL33_34-001(17AB017) 4
Attached sheet 1 (4/7)
MSB-17EXL33_34-001(17AB017) 5
Attached sheet 1 (5/7)
SERVICE SPECIFICATIONS
(M332-00-032-22500-01)
FRONT WHEEL ALIGNMENT CHECK AND Attached sheet 7
PWFE1301R (ENG) ADUTMENT
2014 (M331-00-091-89000-01)
PWFS1302R (SPA)
MIRAGE/SPACE STAR
DRAFT (Thailand, SERVICE SPECIFICATIONS
Workshop Manual
South Africa) (M341-00-012-35900-01)
REAR WHEEL ALIGNMENT CHECK AND Attached sheet 8
ADUTMENT
(M341-01-101-26700-01)
SERVICE SPECIFICATIONS
(M332-00-032-22500-01)
FRONT WHEEL ALIGNMENT CHECK AND Attached sheet 7
PWFE1405R (ENG) ADUTMENT
2015 PWFS1406R (SPA) (M331-00-091-89000-01)
MIRAGE/SPACE STAR DRAFT (Thailand,
Workshop Manual Morocco, Chile, SERVICE SPECIFICATIONS
Argentina, Mexico) (M341-00-012-35900-01)
REAR WHEEL ALIGNMENT CHECK AND Attached sheet 8
ADUTMENT
(M341-01-101-26700-01)
SERVICE SPECIFICATIONS
(M332-00-032-22500-01)
FRONT WHEEL ALIGNMENT CHECK AND Attached sheet 6
ADUTMENT
2016 (M331-00-091-89000-01)
MIRAGE DRAFT (Thailand)
Workshop Manual SERVICE SPECIFICATIONS
(M341-00-012-35900-01)
REAR WHEEL ALIGNMENT CHECK AND Attached sheet 5
ADUTMENT
(M341-01-101-26700-01)
SERVICE SPECIFICATIONS
(M332-00-032-22500-01)
FRONT WHEEL ALIGNMENT Attached sheet 2
PWFE1601R (ENG) CHECK AND ADUTMENT
2017 PWFS1602R (SPA) (M331-00-091-89000-01)
MIRAGE/SPACE STAR DRAFT (Morocco,
Workshop Manual Chile, South Africa, SERVICE SPECIFICATIONS
Mexico) (M341-00-012-35900-01)
REAR WHEEL ALIGNMENT Attached sheet 3
CHECK AND ADUTMENT
(M341-01-101-26700-01)
MSB-17EXL33_34-001(17AB017) 6
Attached sheet 1 (6/7)
SERVICE SPECIFICATIONS
(M332-00-032-22500-01)
FRONT WHEEL ALIGNMENT CHECK AND Attached sheet 4
PWFE1305R (ENG) ADUTMENT
2014 PWFS1306R (SPA) (M331-00-091-89000-01)
ATTRAGE/MIRAGE G4 DRAFT (Thailand,
Workshop Manual ASEAN, Chile, SERVICE SPECIFICATIONS
Argentina) (M341-00-012-35900-01)
REAR WHEEL ALIGNMENT CHECK AND Attached sheet 5
ADUTMENT
(M341-01-101-26700-01)
SERVICE SPECIFICATIONS
(M332-00-032-22500-01)
FRONT WHEEL ALIGNMENT CHECK AND Attached sheet 4
PWFE1410R (ENG) ADUTMENT
2015 (M331-00-091-89000-01)
PWFS1411R (SPA)
ATTRAGE/MIRAGE G4
DRAFT (Thailand, SERVICE SPECIFICATIONS
Workshop Manual
Argentina, ASEAN) (M341-00-012-35900-01)
REAR WHEEL ALIGNMENT CHECK AND Attached sheet 5
ADUTMENT
(M341-01-101-26700-01)
SERVICE SPECIFICATIONS
(M332-00-032-22500-01)
FRONT WHEEL ALIGNMENT CHECK AND Attached sheet 4
PWFE1514R (ENG) ADUTMENT
2017 (M331-00-091-89000-01)
PWFS1515R (SPA)
ATTRAGE/MIRAGE G4
DRAFT (Thailand, SERVICE SPECIFICATIONS
Workshop Manual
Argentina, ASEAN) (M341-00-012-35900-01)
REAR WHEEL ALIGNMENT CHECK AND Attached sheet 5
ADUTMENT
(M341-01-101-26700-01)
PHILIPPINE
Applicable manual Pub. No. Applicable title (INFO ID) Contents
MSB-17EXL33_34-001(17AB017) 7
Attached sheet 1 (7/7)
MSB-17EXL33_34-001(17AB017) 8
Attached sheet 2 (1/2)
GENERAL
M1332000102458
SERVICE SPECIFICATIONS
M1332000302247
SPECIAL TOOLS
M1332000601234
MB991004
MSB-17EXL33_34-001(17AB017) 9
Attached sheet 2 (2/2)
FRONT SUSPENSION
ON-VEHICLE SERVICE
33-3
ON-VEHICLE SERVICE
FRONT WHEEL ALIGNMENT CHECK AND Item Specification
ADJUSTMENT Kingpin inclination 1135' 130'
M1331000901919
Measure wheel alignment with alignment equipment NOTE: .
on a level surface. The front suspension, steering *: Difference between right and left wheels must
system, wheels, and tyres should be serviced to nor- be 030' or less.
mal condition before measuring wheel alignment. The camber and the caster are pre-adjusted at
. factory and not adjustable.
TOE-IN Toe-angle (per wheel): 0°00' ± 0°09'
CAUTION
Standard value: <Added>
Do not apply the vehicle weight to the wheel
At the centre of tyre tread: 0 3 mm bearing while loosening the driveshaft nut.
MB991004
Clip
Lock nut
AC209087AE AC608295AB
1. Adjust the toe-in by undoing the clip and lock nut, NOTE: .
and turning the left and right tie rod turnbuckles by For vehicles with aluminium wheels, tighten spe-
the same amount (in opposite directions). cial tool wheel alignment gauge attachment
NOTE: The toe will move out as the left turnbuckle (MB991004) to the specified torque, then meas-
is turned toward the front of the vehicle and the ure the camber.
right turnbuckle is turned toward the rear of the Tightening torque: 250 25 Nm
vehicle.
2. Install the clip and tighten the lock nut to the
specified torque.
Compensator
Tightening torque: 34 5 Nm
3. Confirm that the toe-in is at the standard value.
4. Use a turning radius gauge to check that the
steering angle is at the standard value.
.
AC102503AD
CAMBER, CASTER AND KINGPIN INCLINATION
Standard value: NOTE: .
For vehicles with aluminium wheels, we recom-
Item Specification mend that a compensator be used to measure
Camber 005' 045'* the camber.
Caster 400' 045'*
MSB-17EXL33_34-001(17AB017) 10
Attached sheet 3
REAR SUSPENSION
SERVICE SPECIFICATIONS
SERVICE SPECIFICATIONS
M1341000301327
ON-VEHICLE SERVICE
REAR WHEEL ALIGNMENT CHECK AND NOTE: .
ADJUSTMENT The difference between right and left wheels
must be less than 30'
Measure wheel alignment with an alignment equip- The camber is pre-adjusted at factory and is not
ment on level earth. adjustable.
The rear suspension, wheels, and tyres should be
serviced to the normal condition prior to wheel align-
ment measurement.
.
Compensator
TOE-IN
Standard value:
At the centre of tyre tread: 2.5 3 mm
NOTE: .
<Added> The toe-in is pre-adjusted at factory and is not
adjustable. AC102503AD
<Added> The toe-angle value is a total for both wheels.
.
.
CAMBER
For vehicles with aluminium wheels, we recom-
Standard value: 100' 045' mend that a compensator be used to measure
<Added>
the camber and caster.
Toe-angle (total value of both wheels):
0°15' ± 0°18'
MSB-17EXL33_34-001(17AB017) 11
Attached sheet 4 (1/2)
SERVICE SPECIFICATIONS
M1332000302311
MSB-17EXL33_34-001(17AB017) 12
Attached sheet 4 (2/2)
)52176863(16,21
219(+,&/(6(59,&(
219(+,&/(6(59,&(
)5217:+((/$/,*10(17&+(&.$1' CAUTION
$'-8670(17 'RQRWDSSO\WKHYHKLFOHZHLJKWWRWKHZKHHO
M1331000901964 EHDULQJZKLOHORRVHQLQJWKHGULYHVKDIWQXW
Measure wheel alignment with alignment equipment
NOTE: .
on a level surface. The front suspension, steering
Clip AC608295AB
specified torque.
NOTE: .
7LJKWHQLQJWRUTXH1P For vehicles with aluminium wheels, we recom-
3. Confirm that the toe-in is at the standard value. mend that a compensator be used to measure
4. Use a turning radius gauge to check that the the camber.
steering angle is at the standard value (Refer to ).
/2:(5$50%$//-2,173/$<&+(&.
M1332015000398
1. Raise the vehicle.
.
&$0%(5&$67(5$1'.,1*3,1,1&/,1$7,21
6WDQGDUGYDOXH 2. Move the lower arm up and down by hand, and
check for the ball joint axial play. If there is a play,
,WHP 6SHFLILFDWLRQ replace the lower arm assembly.(Refer to .)
Camber 005' 045'*
/2:(5$50%$//-2,17'867&29(5
Caster 405' 045'*
&+(&.
Kingpin inclination 1135' 130' M1332008601108
1. Press the lower arm ball joint dust cover with your
NOTE: .
finger to check that there are no cracks or
*: Difference between right and left wheels must
damage in the lower arm ball joint cover.
be 030' or less.
The camber and the caster are pre-adjusted at 2. If the lower arm ball joint dust cover is cracked or
factory and not adjustable. damaged, replace the lower arm assembly (Refer
to ).
MSB-17EXL33_34-001(17AB017) 13
Attached sheet 5
REAR SUSPENSION
SERVICE SPECIFICATIONS
SERVICE SPECIFICATIONS
M1341000301327
ON-VEHICLE SERVICE
REAR WHEEL ALIGNMENT CHECK AND NOTE: .
ADJUSTMENT The difference between right and left wheels
must be less than 30'
Measure wheel alignment with an alignment equip- The camber is pre-adjusted at factory and is not
ment on level earth. adjustable.
The rear suspension, wheels, and tyres should be
serviced to the normal condition prior to wheel align-
ment measurement.
.
Compensator
TOE-IN
Standard value:
At the centre of tyre tread: 3 3 mm
NOTE: .
<Added> The toe-in is pre-adjusted at factory and is not
adjustable. AC102503AD
<Added> The toe-angle value is a total for both wheels.
.
.
CAMBER
For vehicles with aluminium wheels, we recom-
Standard value: 100' 045' mend that a compensator be used to measure
<Added>
the camber and caster.
Toe-angle (total value of both wheels):
0°18' ± 0°18'
MSB-17EXL33_34-001(17AB017) 14
Attached sheet 6 (1/2)
SERVICE SPECIFICATIONS
M1332000302225
MSB-17EXL33_34-001(17AB017) 15
Attached sheet 6 (2/2)
FRONT SUSPENSION
ON-VEHICLE SERVICE
ON-VEHICLE SERVICE
FRONT WHEEL ALIGNMENT CHECK AND Item Specification
ADJUSTMENT Kingpin inclination 1150' 130'
M1331000901890
Measure wheel alignment with alignment equipment NOTE: .
on a level surface. The front suspension, steering *: Difference between right and left wheels must
system, wheels, and tyres should be serviced to nor- be 030' or less.
mal condition before measuring wheel alignment. The camber and the caster are pre-adjusted at
. factory and not adjustable.
TOE-IN Toe-angle (per wheel): 0°00' ± 0°09'
<Added>
CAUTION
Standard value: Do not apply the vehicle weight to the wheel
At the centre of tyre tread: 0 3 mm bearing while loosening the driveshaft nut.
NOTE:
Clip MB991004
Lock nut
AC209087AE
AC608295AB
1. Adjust the toe-in by undoing the clip and lock nut,
.
and turning the left and right tie rod turnbuckles by
For vehicles with aluminium wheels, tighten spe-
the same amount (in opposite directions).
cial tool wheel alignment gauge attachment
NOTE: The toe will move out as the left turnbuckle (MB991004) to the specified torque, then meas-
is turned toward the front of the vehicle and the ure the camber.
right turnbuckle is turned toward the rear of the
Tightening torque: 250 25 Nm
vehicle.
NOTE:
2. Install the clip and tighten the lock nut to the
specified torque.
Tightening torque: 34 5 Nm
Compensator
3. Confirm that the toe-in is at the standard value.
4. Use a turning radius gauge to check that the
steering angle is at the standard value (Refer to ).
MSB-17EXL33_34-001(17AB017) 16
Attached sheet 7 (1/2)
SERVICE SPECIFICATIONS
M1332000302322
MSB-17EXL33_34-001(17AB017) 17
Attached sheet 7 (2/2)
ON-VEHICLE SERVICE
FRONT WHEEL ALIGNMENT CHECK AND Item Specification
ADJUSTMENT Kingpin inclination 1150' 130'
M1331000902008
Measure wheel alignment with alignment equipment NOTE: . <Incorrect>
on a level surface. The front suspension, steering *: Difference between right and left wheels must
system, wheels, and tyres should be serviced to nor- be 030' or less.
mal condition before measuring wheel alignment. The camber and the caster are pre-adjusted at
. factory and not adjustable.
TOE-IN Toe-angle (per wheel): 0°00' ± 0°09'
CAUTION
Standard value: <Added>
Do not apply the vehicle weight to the wheel
At the centre of tyre tread: 0 3 mm bearing while loosening the driveshaft nut.
MB991004
Clip
Lock nut
AC209087AE AC608295AB
1. Adjust the toe-in by undoing the clip and lock nut, NOTE: .
and turning the left and right tie rod turnbuckles by For vehicles with aluminium wheels, tighten spe-
the same amount (in opposite directions). cial tool wheel alignment gauge attachment
NOTE: The toe will move out as the left turnbuckle (MB991004) to the specified torque, then meas-
is turned toward the front of the vehicle and the ure the camber.
right turnbuckle is turned toward the rear of the Tightening torque: 250 25 Nm
vehicle.
2. Install the clip and tighten the lock nut to the
specified torque.
Compensator
Tightening torque: 34 5 Nm
3. Confirm that the toe-in is at the standard value.
4. Use a turning radius gauge to check that the
steering angle is at the standard value (Refer to ).
.
AC102503AD
CAMBER, CASTER AND KINGPIN INCLINATION
Standard value: NOTE: .
For vehicles with aluminium wheels, we recom-
Item Specification mend that a compensator be used to measure
Camber Vehicles with 005' 045'* the camber.
standard suspension
LOWER ARM BALL JOINT PLAY CHECK
Vehicles with high 005' 045'* M1332015000398
ground clearance 1. Raise the vehicle.
<Incorrect> suspension 2. Move the lower arm up and down by hand, and
Caster 405' 045'* check for the ball joint axial play. If there is a play,
replace the lower arm assembly.(Refer to .)
<Correct> <Correct>
Caster Vehicles with 4°05′ ± 0° 45′* Kingpin Vehicles with 11°50′ ± 1° 30′
standard suspension inclination standard suspension
Vehicles with high 4°00′ ± 0° 45′* Vehicles with high 11°35′ ± 1° 30′
ground clearance
MSB-17EXL33_34-001(17AB017) 18 ground clearance
suspension suspension
Attached sheet 8
REAR SUSPENSION
SERVICE SPECIFICATIONS
SERVICE SPECIFICATIONS
M1341000301532
ON-VEHICLE SERVICE
REAR WHEEL ALIGNMENT CHECK AND CAMBER
ADJUSTMENT Standard value: 100' 045'
M1341011001364
NOTE: .
Measure wheel alignment with an alignment equip- Difference between right and left wheels must be
ment on level earth. 030' or less.
The rear suspension, wheels, and tyres should be The camber is pre-adjusted at factory and is not
serviced to the normal condition prior to wheel align- adjustable.
ment measurement.
.
TOE-IN
Standard value:
Compensator
<Vehicles with standard suspension>
At the centre of tyre tread: 3 3 mm
<Vehicles with high ground clearance sus-
pension>
At the centre of tyre tread: 2.5 3 mm
AC102503 AD
NOTE: .
<Added> The toe-in is pre-adjusted at factory and is not .
adjustable. For vehicles with aluminium wheels, we recom-
<Added> The toe-angle value is a total for both wheels.
.
mend that a compensator be used to measure
<Added> the camber.
Toe-angle (total value of both wheels):
0°15' ± 0°18'
<Added>
Toe-angle (total value of both wheels):
0°18' ± 0°18'
MSB-17EXL33_34-001(17AB017) 19