You are on page 1of 46

ADJUSTABLE CRS

POWER

AT&T LTE FFA L14A INDIANAPOLIS


contents

› Feature Introduction
› Test Location and Configuration
› KPI Analysis
› Appendix

Ericsson Internal | 2014-07-25 | Page 2


contents

› Feature Introduction
› Test Location and Configuration
› KPI Analysis
› Appendix

Ericsson Internal | 2014-07-25 | Page 3


Feature introduction
Adjustable CRS Power is a Basic Feature in L14A. The feature was
available and controllable in previous SW releases via System Constants.

Description:
 Enables flexible setting of the Cell Reference Signal (CRS) power
(Pa) with new parameter EUtrancellFDD::crsGain
 Enables flexible setting of the type-B resource element power
(PDSCH) with new parameter EUtrancellFDD:: zzzTemporary14
 Combinations leading to over allocation of the power are restricted
Feature benefit:
 Improved flexibility for tuning and optimization of downlink resource
element power allocation
 Improved DL throughput, by reduced interference*

*Note: The results may vary from one market to another depending on the traffic patterns. In addition, the reduced
interference is the primary factor for improving DL Throughput, this could be achieved via the new L14A default
settings in comparison to the legacy L13B settings.
Ericsson Internal | 2014-07-25 | Page 4
Feature introduction
- Controls CRS Power Boost Setting (𝑃𝑎 ) in the range +3dB to -3dB
(previously fixed to +3dB)
- Controls Type-B resource element boosting (𝑃𝑏 𝑃𝑎 ) in the range,
5/4, 1, 3/4 𝑜𝑟 1/2 (previously fixed to 1)

Ericsson Internal | 2014-07-24 | Page 5


Parameter Definitions
MO Attribute MOM / SC Range Unit Default GS Description

New in L14A:

-300, Sets the DL power of the cell specific


-200, Reference Symbols (RS) relatively, a
-100, reference level defined by the power of
0, the PDSCH type A resource elements.
EUtranCellFDD crsGain MOM 0.01 dB 0 300 If crsGain is +3dB, the power of the RS is
177,
300, 3dB higher than a PDSCH type A
477, resource element.
600

Change takes effect: Cell lock/unlock

- CrsGain is a new parameter in L14A IP4.


- From L14A IP4, it is possible to change the value from -300 to 600.
- Setting crsGain > 300 -> EnodeB will automatically limit the value to 300 for 2-Tx EnodeB.
- crsGain corresponds to −𝑃𝑎 , minus 𝑃𝑎 (36.213).
- Hard-coded in L13B -> 300 dB [ p-a: dB-3]
- New default value for L14A -> 0 dB [ p-a: dB0 ]

ADJUSTABLE CRS POWER | Ericsson Confidential | 2014-02-22 | Page 6


Parameter Definitions
MO Attribute MOM / SC Range Unit Default GS Description

New in L14A:
It specifies the power level of PDSCH type
B resource elements according to a power
gain which is set relatively to resource
elements of PDSCH type A.

0 zzzTemporary14 will be replaced with the


1
EUtranCellFDD zzzTemporary14 MOM N/A 0 1 MOM parameter pdschTypeBGain in a
2 later release.
3
Range: {0, 1, 2, 3} which corresponds to a
factor of { 5/4, 1, 3/4, 1/2 } according to
3GPP TS 36.213

Change takes effect: Cell lock/unlock

- zzzTemporary14 is a new parameter for pdschTypeBGain in L14A IP4.


- From L14A IP4, it is possible to change the alue from 0 to 3.
Caution: There is another zzzTemporary14 under EnodeBFunction MO that is not related to this feature.

- parameter pdschTypeBGain corresponds to 𝑃𝐵 or Threshold 𝑃𝐵 𝑃𝐴 (36.213).


- Hard-coded in L13B -> 1 [ p-b:1] -> 𝑃𝐵 𝑃𝐴 = 1
- New default value for L14A -> 0 [ p-b:0 ] -> 𝑃𝐵 𝑃𝐴 = 5/4
ADJUSTABLE CRS POWER | Ericsson Confidential | 2014-02-22 | Page 7
Feature introduction
L13B Default settings
- CrsGain = 3dB
- PdschTypeBGain = 1
- Full utilization is obtained since Boosted RS consumes all power in empty RE
- PdschTypeBGain=5/4 gives over allocation on symbol B (7 ∗ 𝑃𝑟𝑒𝑓 )
Controls CRS Power Boost Setting (𝑃𝑎 ) in the range +3dB to -3dB (previously
fixed to +3dB)

Ericsson Internal | 2014-07-24 | Page 8


Feature introduction
L14A Default settings
- CrsGain = 0dB Gives Full utilization on Type B symbol = 6 ∗ 𝑃𝑟𝑒𝑓
- PdschTypeBGain = 5/4

Note: The default behavior of the system will change from L13B to L14A, if the
above MoM parameters are not set to match the L13B settings.

Ericsson Internal | 2014-07-24 | Page 9


Feature introduction
Legacy In L14A, it is possible to set the CRS
L14A
In legacy SW, the CRS Gain
and PDSCH Type-B Gain were Gain and PDSCH Type-B Gain via MoM
system constants. parameters, in addition, the new default
settings could decrease the Inter-Cell
interference.

‘Adjustable CRS Power’ is a Basic L14A feature

› Benefits:
– In L14A, it is possible to set the boost level on CRS and PDSCH Type-B resource
via MoM parameters, i.e. replacing system constants.
– The combination CrsGain=3 and zzzTemporary14=1 gives the L13B legacy
behavior.
– The L14A default settings, CrsGain=0 & zzzTemporary14=0, can decrease the
Inter-Cell interference.
– Both combinations, L13B & L14A default settings, give full utilization of DL Power.
Cell Soft Lock | Ericsson Internal | 2014-07-15 | Page 10
contents

› Feature Introduction
› Test Location and Configuration
› KPI Analysis
› Appendix

Ericsson Internal | 2014-07-25 | Page 11


Test location
Legacy Group 3
Group 5
Group 6

Bucket
Terre Haute
Group 4
Group 1

Group 2

Group 7

Ericsson Internal | 2014-07-25 | Page 12


Test configuration
eNodeB
– Sites: INL00505, INL00508, INL00511, INL00522, INL00532,
INL00542, INL01116
– SW Version: L14A IP4 (CXP102051/21_R28AY)
– Frequency Band: AWS
– Bandwidth: 5MHz

Ericsson Internal | 2014-07-25 | Page 13


Test configuration
The general KPI’s were monitored over two test phases, each phase
had different CRS settings, and they were defined as follows:

- Phase#1 (L13B Legacy): L13B Default CRS Settings


- CrsGain = 300 (3dB)
𝑃
- zzzTemporary14 (PdschTypeBGain) = 1 → ( 𝑏 𝑃 = 1)
𝑎

- Phase#2 (L14A Default): Change the settings to the L14A default


settings
- CrsGain = 0 (0dB)
𝑃𝑏
- zzzTemporary14 (PdschTypeBGain) = 0 → ( 𝑃𝑎 = 5/4)

Ericsson Internal | 2014-07-25 | Page 14


contents

› Feature Introduction
› Test Location and Configuration
› KPI Analysis
› Appendix

Ericsson Internal | 2014-07-25 | Page 15


INDY FFA L14A CRS FEATURE – 7 SITES
ACCESSIBILITY Trend – DAILY
L13B Legacy Settings L14A Default Settings

L14A-IP4> L14A-IP6

CRS_Power changes
FGA33 & lock/unlock cells
1400000 100

99.95
1200000

RRC -S1 ERAB & LTE ACC [%]


99.9

1000000 99.85
PM Counter

99.8
800000

99.75

600000
99.7

400000 99.65

99.6
200000
99.55

0 99.5
07/01/14 07/02/14 07/03/14 07/07/14 07/08/14 07/09/14 07/10/14 07/11/14 07/14/14 07/15/14 07/16/14

pmRrcConnEstabAtt pmRrcConnEstabSucc pmRrcConnEstabAttReatt


KPI-Accessibility LTE [%] (EUtranCellFDD Daily) KPI-Access RRC Estab SR [%] (EUtranCellFDD Daily) KPI-Access S1 Estab SR [%] (EUtranCellFDD Daily)
KPI-Access Erab Estab SR [%] (EUtranCellFDD Daily)

Cell coverage shrunk after the parameter change, consequently reduction in RRC attempts observed.

Ericsson Internal | 2014-07-25 | Page 16


INDY FFA L14A CRS FEATURE – 7 SITES
RetainabilitY trend – DAILY
L13B Legacy Settings L14A Default Settings

L14A-IP4> L14A-IP6

CRS_Power changes
FGA33 & lock/unlock cells
1200 100

99.95

1000
99.9

99.85
800

Retainability [%]
99.8
PM Counter

600 99.75

99.7

400
99.65

99.6
200

99.55

0 99.5
07/01/14 07/02/14 07/03/14 07/07/14 07/08/14 07/09/14 07/10/14 07/11/14 07/14/14 07/15/14 07/16/14

pmErabRelAbnormalMmeAct pmErabRelAbnormalEnbAct KPI-Retainability [%] (EUtranCellFDD Daily)

Decrease in abnormal releases due to reduced traffic.

Ericsson Internal | 2014-07-25 | Page 17


INDY FFA L14A CRS FEATURE – 7 SITES
HO Prep INTRA SR – DAILY
L13B Legacy Settings L14A Default Settings

L14A-IP4> L14A-IP6

CRS_Power changes
FGA33 & lock/unlock cells
200000 100

180000

99.5
160000

INTRA-FREQ HO PREP SR[%]


140000
99

120000
PM Counter

100000 98.5

80000

98
60000

40000
97.5

20000

0 97
07/01/14 07/02/14 07/03/14 07/07/14 07/08/14 07/09/14 07/10/14 07/11/14 07/14/14 07/15/14 07/16/14

pmHoPrepAttLteIntraF pmHoPrepSuccLteIntraF KPI-Handover Prep Intra SR [%] (EUtranRelationFDD Daily)

Cell coverage shrunk after the parameter change, consequently reduction in HO attempts observed.

Ericsson Internal | 2014-07-25 | Page 18


INDY FFA L14A CRS FEATURE – 7 SITES
HO EXEC INTRA SR – DAILY
L13B Legacy Settings L14A Default Settings

L14A-IP4> L14A-IP6

CRS_Power changes
FGA33 & lock/unlock cells
200000 100

180000

99.5
160000

INTRA-FREQ HO EXEC SR[%]


140000
99

120000
PM Counter

100000 98.5

80000

98
60000

40000
97.5

20000

0 97
07/01/14 07/02/14 07/03/14 07/07/14 07/08/14 07/09/14 07/10/14 07/11/14 07/14/14 07/15/14 07/16/14

pmHoExeAttLteIntraF pmHoExeSuccLteIntraF KPI-Handover Exe Intra SR [%] (EUtranRelationFDD Daily)

Cell coverage shrunk after the parameter change, consequently reduction in HO attempts observed.

Ericsson Internal | 2014-07-25 | Page 19


INDY FFA L14A CRS FEATURE – 7 SITES
HO Prep INTER SR – DAILY
L13B Legacy Settings L14A Default Settings

L14A-IP4> L14A-IP6

CRS_Power changes
FGA33 & lock/unlock cells
160 100

140
99.5

INTER-FREQ HO PREP SR[%]


120

99
100
PM Counter

80 98.5

60
98

40

97.5
20

0 97
07/01/14 07/02/14 07/03/14 07/07/14 07/08/14 07/09/14 07/10/14 07/11/14 07/14/14 07/15/14 07/16/14

pmHoPrepAttLteInterF pmHoPrepSuccLteInterF KPI-Handover Prep Inter SR [%] (EUtranRelationFDD Daily)

Cell coverage shrunk after the parameter change, consequently reduction in HO attempts observed.

Ericsson Internal | 2014-07-25 | Page 20


INDY FFA L14A CRS FEATURE – 7 SITES
HO EXEC INTER SR – DAILY
L13B Legacy Settings L14A Default Settings

L14A-IP4> L14A-IP6

CRS_Power changes
FGA33 & lock/unlock cells
160 100

140
99.5

INTER-FREQ HO EXEC SR[%]


120

99
100
PM Counter

80 98.5

60
98

40

97.5
20

0 97
07/01/14 07/02/14 07/03/14 07/07/14 07/08/14 07/09/14 07/10/14 07/11/14 07/14/14 07/15/14 07/16/14

pmHoExeAttLteInterF pmHoExeSuccLteInterF KPI-Handover Exe Inter SR [%] (EUtranRelationFDD Daily)

Cell coverage shrunk after the parameter change, consequently reduction in HO attempts observed.

Ericsson Internal | 2014-07-25 | Page 21


INDY FFA L14A CRS FEATURE – 7 SITES
UL Pathloss distribution
L13B Legacy Settings L14A Default Settings

CRS Change
A reduction is observed on the high bins of the UL Path Loss counter. That
basically indicates that the cell coverage has shrunk and there are less
users with high Path Losses.
Ericsson Internal | 2014-07-25 | Page 22
INDY FFA L14A CRS FEATURE – 7 SITES
DL TPUT Trend – DAILY
L13B Legacy Settings L14A Default Settings

L14A-IP4> L14A-IP6

CRS_Power changes
FGA33 & lock/unlock cells
1600000000 9

8
1400000000

KPI-Throughput DL User [Mbps] (Daily)


7
1200000000

6
pmPdcpVolDlDrb

1000000000

800000000

600000000
3

400000000
2

200000000
1

0 0
07/01/14 07/02/14 07/03/14 07/07/14 07/08/14 07/09/14 07/10/14 07/11/14 07/14/14 07/15/14 07/16/14

pmPdcpVolDlDrb KPI-Throughput DL User [Mbps] (Daily)

Cell coverage shrunk after the parameter change, consequently reduction in DL Volume observed.

Ericsson Internal | 2014-07-25 | Page 23


INDY FFA L14A CRS FEATURE – 7 SITES
DL TPUT Trend cell – DAILY
L13B Legacy Settings L14A Default Settings

L14A-IP4> L14A-IP6

CRS_Power changes
FGA33 & lock/unlock cells
1600000000 8

1400000000 7

KPI-Throughput DL Cell [Mbps] (Daily)


1200000000 6
pmPdcpVolDlDrb

1000000000 5

800000000 4

600000000 3

400000000 2

200000000 1

0 0
07/01/14 07/02/14 07/03/14 07/07/14 07/08/14 07/09/14 07/10/14 07/11/14 07/14/14 07/15/14 07/16/14

pmPdcpVolDlDrb KPI-Throughput DL Cell [Mbps] (Daily)

Cell coverage shrunk after the parameter change, consequently reduction in DL Volume observed.

Ericsson Internal | 2014-07-25 | Page 24


INDY FFA L14A CRS FEATURE – 7 SITES
UL TPUT Trend – DAILY
L13B Legacy Settings L14A Default Settings

L14A-IP4> L14A-IP6

CRS_Power changes
FGA33 & lock/unlock cells
120000000 0.7

0.6

KPI-Throughput UL User [Mbps] (Daily)


100000000

0.5
80000000
pmUeThpVolUl

0.4

60000000

0.3

40000000
0.2

20000000
0.1

0 0
07/01/14 07/02/14 07/03/14 07/07/14 07/08/14 07/09/14 07/10/14 07/11/14 07/14/14 07/15/14 07/16/14

pmUeThpVolUl KPI-Throughput UL User [Mbps] (Daily)

Cell coverage shrunk after the parameter change, consequently reduction in UL Volume observed.

Ericsson Internal | 2014-07-25 | Page 25


INDY FFA L14A CRS FEATURE – 7 SITES
UL TPUT Trend CELL – DAILY
L13B Legacy Settings L14A Default Settings

L14A-IP4> L14A-IP6

CRS_Power changes
FGA33 & lock/unlock cells
200000000 0.7

180000000
0.6

KPI-Throughput UL Cell [Mbps] (Daily)


160000000

0.5
140000000
pmPdcpVolUlDrb

120000000
0.4

100000000

0.3
80000000

60000000
0.2

40000000

0.1
20000000

0 0
07/01/14 07/02/14 07/03/14 07/07/14 07/08/14 07/09/14 07/10/14 07/11/14 07/14/14 07/15/14 07/16/14

pmPdcpVolUlDrb KPI-Throughput UL Cell [Mbps] (Daily)

Cell coverage shrunk after the parameter change, consequently reduction in UL Volume observed.

Ericsson Internal | 2014-07-25 | Page 26


INDY FFA L14A CRS FEATURE – 7 SITES
RRC REEST SR – DAILY
L13B Legacy Settings L14A Default Settings

L14A-IP4> L14A-IP6

CRS_Power changes
FGA33 & lock/unlock cells
18000 100

16000 90

80

KPI-RRC Reestab SR [%] (Daily)


14000

70
12000

60
PM Counter

10000

50

8000
40

6000
30

4000
20

2000 10

0 0
07/01/14 07/02/14 07/03/14 07/07/14 07/08/14 07/09/14 07/10/14 07/11/14 07/14/14 07/15/14 07/16/14

pmRrcConnReestAtt pmRrcConnReestSucc KPI-RRC Reestab SR [%] (Daily)

Ericsson Internal | 2014-07-25 | Page 27


INDY FFA L14A CRS FEATURE – 7 SITES
IRAT – DAILY
L13B Legacy Settings L14A Default Settings

L14A-IP4> L14A-IP6

CRS_Power changes
FGA33 & lock/unlock cells
40000 3.5

35000
3

KPI-IRAT Redirection Rate [%] (Daily)


30000
2.5

25000
PM Counter

20000

1.5
15000

1
10000

0.5
5000

0 0
07/01/14 07/02/14 07/03/14 07/07/14 07/08/14 07/09/14 07/10/14 07/11/14 07/14/14 07/15/14 07/16/14

pmUeCtxtRelSCWcdma pmUeCtxtRelSCGsm pmCriticalBorderEvalReport KPI-IRAT Redirection Rate [%] (EUtranCellFDD Daily)

Cell coverage shrunk after the parameter change, consequently increase in IRAT rate observed.

Ericsson Internal | 2014-07-25 | Page 28


INDY FFA L14A CRS FEATURE – 7 SITES
RRC CONN USERS TREND – DAILY
L13B Legacy Settings L14A Default Settings

L14A-IP4> L14A-IP6

CRS_Power changes
FGA33 & lock/unlock cells
1200 300

1000 250
pmRrcConnMax (sum)

pmRrcConnMax (max)
800 200

600 150

400 100

200 50

0 0
07/01/14 07/02/14 07/03/14 07/07/14 07/08/14 07/09/14 07/10/14 07/11/14 07/14/14 07/15/14 07/16/14

pmRrcConnMax (sum) pmRrcConnMax (max)

Cell coverage shrunk after the parameter change, consequently reduction in connected users observed.

Ericsson Internal | 2014-07-25 | Page 29


INDY FFA L14A CRS FEATURE – 7 SITES
CS FALLBACK– DAILY
L13B Legacy Settings L14A Default Settings

L14A-IP4> L14A-IP6

CRS_Power changes
FGA33 & lock/unlock cells
30000

25000
pmUeCtxtRelCsfbWcdma

20000

15000

10000

5000

0
07/01/14 07/02/14 07/03/14 07/07/14 07/08/14 07/09/14 07/10/14 07/11/14 07/14/14 07/15/14 07/16/14

pmUeCtxtRelCsfbWcdma

Ericsson Internal | 2014-07-25 | Page 30


INDY FFA L14A CRS FEATURE – 7 SITES
LATENCY – DAILY
L13B Legacy Settings L14A Default Settings

L14A-IP4> L14A-IP6

CRS_Power changes
FGA33 & lock/unlock cells
500000000 16

450000000
14

400000000
12

KPI-Latency [ms] (Daily)


350000000
pmPdcpLatTimeDl

10
300000000

250000000 8

200000000
6

150000000
4
100000000

2
50000000

0 0
07/01/14 07/02/14 07/03/14 07/07/14 07/08/14 07/09/14 07/10/14 07/11/14 07/14/14 07/15/14 07/16/14

pmPdcpLatTimeDl KPI-Latency [ms] (EUtranCellFDD Daily)

Ericsson Internal | 2014-07-25 | Page 31


INDY FFA L14A CRS FEATURE – 7 SITES
Random ACCess – DAILY
L13B Legacy Settings L14A Default Settings

L14A-IP4> L14A-IP6

CRS_Power changes
FGA33 & lock/unlock cells
3000000 100

90

2500000
80

70

KPI-RA SR [%] (Daily)


2000000

60
PM Counter

1500000 50

40

1000000
30

20
500000

10

0 0
07/01/14 07/02/14 07/03/14 07/07/14 07/08/14 07/09/14 07/10/14 07/11/14 07/14/14 07/15/14 07/16/14

pmRaAttCbra pmRaSuccCbra KPI-RA SR [%] (EUtranCellFDD Daily)

Cell coverage shrunk after the parameter change, consequently reduction in RA attempts observed.

Ericsson Internal | 2014-07-25 | Page 32


KPI
Conclusion
› After the CRS Power changes the following observations were made:
– Reduction in traffic observed due to reduced CRS Gain which shrunk
the cell coverage.
– IRAT redirection rate increased.
– The benefit of this feature is the possibility to set boost on CRS and
PDSCH type-B resource via MOM parameter, i.e. replacing system
constants.
– Combination CrsGain=3, zzzTemporary14=1(default in L13B) gives
legacy behavior.
– Combination CrsGain=0, zzzTemporary14=0 (default in L14A) can
decrease Inter-Cell interference.
– Both 3/1 and 0/0 combinations give full utilization of DL Power.
– CrsGain affects power of Cell Reference Signal, hence it affects RSRP,
therefore, mobility parameters need to be adjusted accordingly if
CrsGain is changed.

Ericsson Internal | 2014-07-25 | Page 33


Appendix
Feature REstriction
To prevent Over Power Allocation of the RF SignalPower
 If CrsGain = 177 or 300 & PdschTypeBGain = 0 meant 5/4 , the
PdschTypeBGain is remapped to 1.
 If CrsGain = 477 or 600 , the CrsGain is overwritten to 300 (These two
values: 477 or 600 will be removed in a later release)
MOM
MOM
Number Param RefSignal
Param p-a p-b Pathloss RSRP Comment
#TX zzzTemporary14 Pwr
crsGain
(pdschTypeBGain)
2 - TX set = 300 set = 1 dB-3 1 128 20 -108 ** L13B Legacy
2 - TX set = 0 Default = 0 dB0 0 128 17 -111 ** L14A Value
2 - TX set = 177 Default = 0 dB-1dot77 1 128 19 -109 *Restriction
2 - TX set = 300 Default = 0 dB-3 1 128 20 -108 *Restriction
2 - TX set = 477 Default = 0 dB-3 1 128 20 -108 *Restriction
2 - TX set = 600 Default = 0 dB-3 1 128 20 -108 *Restriction

Ericsson Internal | 2014-07-25 | Page 36


Lab Test Results
MOM
MOM
Number Param RefSignal
Param Pathloss p-A p-B RSRP RSRQ Comment
#TX zzzTemporary14 Pwr
crsGain
(pdschTypeBGain)
2 - TX set = 300 set = 1 (1) 128 dB-3 1 20 -108 -9 ** L13B Legacy
2 - TX default = 0 Default = 0 (5/4) 128 dB0 0 17 -111 -12 ** L14A Value
2 - TX Default = 0 set = 0 (5/4) 128 dB0 0 17 -111 -12
2 - TX Default = 0 set = 1 (1) 128 dB0 1 17 -111 -11
2 - TX Default = 0 set = 2 (3/4) 128 dB0 2 17 -111 -10
2 - TX Default = 0 set = 3 (1/2) 128 dB0 3 17 -111 -9

ADJUSTABLE CRS POWER | Ericsson Confidential | 2014-02-22 | Page 37


INDY FFA L14A CRS FEATURE – 7 SITES
ANR TREND – DAILY
L13B Legacy Settings L14A Default Settings

L14A-IP4> L14A-IP6

CRS_Power changes
FGA33 & lock/unlock cells
300000000 3

250000000 2.5

KPI-BLER RLC UL [%] (Daily)


200000000 2
PM Counter

150000000 1.5

100000000 1

50000000 0.5

0 0
07/01/14 07/02/14 07/03/14 07/07/14 07/08/14 07/09/14 07/10/14 07/11/14 07/14/14 07/15/14 07/16/14

pmRlcArqUlAck pmRlcArqUlNack KPI-BLER RLC UL [%] (EUtranCellFDD Daily)

Ericsson Internal | 2014-07-25 | Page 38


INDY FFA L14A CRS FEATURE – 7 SITES
HARQ RTX – DAILY
L13B Legacy Settings L14A Default Settings

L14A-IP4> L14A-IP6

CRS_Power changes
FGA33 & lock/unlock cells
180000000 12

160000000
10
140000000

HARQ RETX RATE [%]


120000000 8
PM Counter

100000000
6
80000000

60000000 4

40000000
2
20000000

0 0
07/01/14 07/02/14 07/03/14 07/07/14 07/08/14 07/09/14 07/10/14 07/11/14 07/14/14 07/15/14 07/16/14

pmMacHarqDlAckQpsk pmMacHarqDlNackQpsk
pmMacHarqDlAck16qam pmMacHarqDlNack16qam
pmMacHarqDlAck64qam pmMacHarqDlNack64qam
KPI-HARQ RETX 16 QAM DL [%] (EUtranCellFDD Daily) KPI-HARQ RETX 64 QAM DL [%] (EUtranCellFDD Daily)
KPI-HARQ RETX QPSK DL [%] (EUtranCellFDD Daily)

Ericsson Internal | 2014-07-25 | Page 39


INDY FFA L14A CRS FEATURE – 7 SITES
pmPUCCHFAILSR-DAILY/HOURLY
L13B Legacy Settings L14A Default Settings

L14A-IP4> L14A-IP6

CRS_Power changes
FGA33 & lock/unlock cells
50000

45000

40000

35000

30000
PM Counter

25000

20000

15000

10000

5000

0
07/01/14 07/02/14 07/03/14 07/07/14 07/08/14 07/09/14 07/10/14 07/11/14 07/14/14 07/15/14 07/16/14

pmPucchFailSr

Ericsson Internal | 2014-07-25 | Page 40


INDY FFA L14A CRS FEATURE – 7 SITES
PAGING – DAILY
L13B Legacy Settings L14A Default Settings

L14A-IP4> L14A-IP6

CRS_Power changes
FGA33 & lock/unlock cells
6000000 6000000

5000000 5000000

4000000 4000000
pmPagDiscarded

pmPagReceived
3000000 3000000

2000000 2000000

1000000 1000000

0 0
07/01/14 07/02/14 07/03/14 07/07/14 07/08/14 07/09/14 07/10/14 07/11/14 07/14/14 07/15/14 07/16/14

pmPagDiscarded pmPagReceived

Ericsson Internal | 2014-07-25 | Page 41


INDY FFA L14A CRS FEATURE – 7 SITES
PACKET LOSS – DAILY
L13B Legacy Settings L14A Default Settings

L14A-IP4> L14A-IP6

CRS_Power changes
FGA33 & lock/unlock cells
1400000 1.2

1200000
1

KPI-UL Packet Loss (%) [Daily)


1000000
0.8
pmPdcpPktLostUl

800000

0.6

600000

0.4
400000

0.2
200000

0 0
07/01/14 07/02/14 07/03/14 07/07/14 07/08/14 07/09/14 07/10/14 07/11/14 07/14/14 07/15/14 07/16/14

pmPdcpPktLostUl KPI-UL Packet Loss (%) [Daily)

Ericsson Internal | 2014-07-25 | Page 42


INDY FFA L14A CRS FEATURE – 7 SITES
RLC BLER DL – DAILY
L13B Legacy Settings L14A Default Settings

L14A-IP4> L14A-IP6

CRS_Power changes
FGA33 & lock/unlock cells
350000000 0.07

300000000 0.06

KPI-BLER RLC DL [%] (Daily)


250000000 0.05
PM Counter

200000000 0.04

150000000 0.03

100000000 0.02

50000000 0.01

0 0
07/01/14 07/02/14 07/03/14 07/07/14 07/08/14 07/09/14 07/10/14 07/11/14 07/14/14 07/15/14 07/16/14

pmRlcArqDlAck pmRlcArqDlNack KPI-BLER RLC DL [%] (EUtranCellFDD Daily)

Ericsson Internal | 2014-07-25 | Page 43


INDY FFA L14A CRS FEATURE – 7 SITES
RLC BLER UL – DAILY
L13B Legacy Settings L14A Default Settings

L14A-IP4> L14A-IP6

CRS_Power changes
FGA33 & lock/unlock cells
300000000 3

250000000 2.5

KPI-BLER RLC UL [%] (Daily)


200000000 2
PM Counter

150000000 1.5

100000000 1

50000000 0.5

0 0
07/01/14 07/02/14 07/03/14 07/07/14 07/08/14 07/09/14 07/10/14 07/11/14 07/14/14 07/15/14 07/16/14

pmRlcArqUlAck pmRlcArqUlNack KPI-BLER RLC UL [%] (EUtranCellFDD Daily)

Ericsson Internal | 2014-07-25 | Page 44


INDY FFA L14A CRS FEATURE – 7 SITES
ACCESSIBILITY Trend – DAILY

L13B Legacy Settings L14A Default Settings L13B Legacy Settings

Accessibility back to normal trend after reverting back the CRS settings.

Ericsson Internal | 2014-07-25 | Page 45


INDY FFA L14A CRS FEATURE – 7 SITES
RetainabilitY trend – DAILY

L13B Legacy Settings L14A Default Settings L13B Legacy Settings

Retainability recovered after reverting back the CRS settings.

Ericsson Internal | 2014-07-25 | Page 46

You might also like