Professional Documents
Culture Documents
ERROR CODE
DANA [HEX] SAE J1939 DM 1 STATUS LAMP ERROR DESCRIPTION TCON ACTION DRIVER ACTION FAILURE CAUSE TROUBLESHOOTING
SPN FMI
The TCON is protecting the transmission Apply the service brakes, and allow the retarder Check the retarder temperature and the
Analog Input function: Transmission retarder and does not allow that the retarder / transmission oil to cool down. Once the The measured value of the retarder retarder temperature sensor.
temperature : Data Valid but Above Normal Operational temperature exceeds its limit. The retarder temperature is below the critical temperature, temperature is above the critical If operating in dirty environment clean out
84.00 120 0 Amber warning Flashing Range - Most Severe function will be gradually to fully disabled resume normal operation. temperature. radiator fins to allow maximum air flow.
TCON will continue normal operation but - Recalibrate the input, if the problem persists,
the measurement of the analogue input check the wiring between the TCON and the
function connected to resistive analogue device connected to this analog input.
input 0 will be affected. - Check installation and operation of the device
This may result in reduced operation of the connected.
Lamp Status Depending On Analogue input 0 (resistive) (ANIA0): Data Valid but vehicle, the TCON action depends on Contact maintenance for troubleshooting or The measured value of the analog input is - refer to the other reported errors to identify
32.00 520208 0 Corresponding Functional Error Above Normal Operational Range - Most Severe configured analog input fiunction Perform a calibration of the connected device. above the maximum allowed range. the affected analogue input function.
TCON will continue normal operation but - Recalibrate the input, if the problem persists,
the measurement of the analogue input check the wiring between the TCON and the
function connected to resistive analogue device connected to this analog input.
input 0 will be affected. - Check installation and operation of the device
This may result in reduced operation of the connected.
Lamp Status Depending On Analogue input 0 (resistive) (ANIA0): Data Valid but vehicle, the TCON action depends on Contact maintenance for troubleshooting or The measured value of the analog input is - refer to the other reported errors to identify
32.01 520208 1 Corresponding Functional Error Below Normal Operational Range - Most Severe configured analog input fiunction Perform a calibration of the connected device. below the minimum allowed range. the affected analogue input function.
ERROR CODE
DANA [HEX] SAE J1939 DM 1 STATUS LAMP ERROR DESCRIPTION TCON ACTION DRIVER ACTION FAILURE CAUSE TROUBLESHOOTING
SPN FMI
TCON will continue normal operation but - Recalibrate the input, if the problem persists,
the measurement of the analogue input check the wiring between the TCON and the
function connected to analogue input 0 will device connected to this analog input.
be affected. - Check installation and operation of the device
This may result in reduced operation of the connected.
Lamp Status Depending On analogue input 1 (resistive) (ANIA1): Data Valid but vehicle, the TCON action depends on Contact maintenance for troubleshooting or The measured value of the analog input is - refer to the other reported errors to identify
33.00 520209 0 Corresponding Functional Error Above Normal Operational Range - Most Severe configured analog input fiunction Perform a calibration of the connected device. above the maximum allowed range. the affected analogue input function.
TCON will continue normal operation but - Recalibrate the input, if the problem persists,
the measurement of the analogue input check the wiring between the TCON and the
function connected to analogue input 0 will device connected to this analog input.
be affected. - Check installation and operation of the device
This may result in reduced operation of the connected.
Lamp Status Depending On analogue input 1 (resistive) (ANIA1): Data Valid but vehicle, the TCON action depends on Contact maintenance for troubleshooting or The measured value of the analog input is - refer to the other reported errors to identify
33.01 520209 1 Corresponding Functional Error Below Normal Operational Range - Most Severe configured analog input fiunction Perform a calibration of the connected device. below the minimum allowed range. the affected analogue input function.
TCON will continue normal operation but - Recalibrate the input, if the problem persists,
the measurement of the analogue input check the wiring between the TCON and the
function connected to analogue input 0 will device connected to this analog input.
be affected. - Check installation and operation of the device
This may result in reduced operation of the connected.
Lamp Status Depending On analogue input C0 (ANIC0): Data Valid but Above Normal vehicle, the TCON action depends on Contact maintenance for troubleshooting or The measured value of the analog input is - refer to the other reported errors to identify
34.00 520210 0 Corresponding Functional Error Operational Range - Most Severe configured analog input fiunction Perform a calibration of the connected device. above the maximum allowed range. the affected analogue input function.
TCON will continue normal operation but - Recalibrate the input, if the problem persists,
the measurement of the analogue input check the wiring between the TCON and the
function connected to analogue input 0 will device connected to this analog input.
be affected. - Check installation and operation of the device
This may result in reduced operation of the connected.
Lamp Status Depending On analogue input C0 (ANIC0): Data Valid but Below Normal vehicle, the TCON action depends on Contact maintenance for troubleshooting or The measured value of the analog input is - refer to the other reported errors to identify
34.01 520210 1 Corresponding Functional Error Operational Range - Most Severe configured analog input fiunction Perform a calibration of the connected device. below the minimum allowed range. the affected analogue input function.
TCON ERROR CODES & DESCRIPTIONS
Revision 2.54 - Firmware Version 2.04
Date: 3/3/2021
ERROR CODE
DANA [HEX] SAE J1939 DM 1 STATUS LAMP ERROR DESCRIPTION TCON ACTION DRIVER ACTION FAILURE CAUSE TROUBLESHOOTING
SPN FMI
TCON will continue normal operation but - Recalibrate the input, if the problem persists,
the measurement of the analogue input check the wiring between the TCON and the
function connected to analogue input 0 will device connected to this analog input.
be affected. - Check installation and operation of the device
This may result in reduced operation of the connected.
Lamp Status Depending On analogue input C1 (ANIC1): Data Valid but Above Normal vehicle, the TCON action depends on Contact maintenance for troubleshooting or The measured value of the analog input is - refer to the other reported errors to identify
35.00 520211 0 Corresponding Functional Error Operational Range - Most Severe configured analog input fiunction Perform a calibration of the connected device. above the maximum allowed range. the affected analogue input function.
TCON will continue normal operation but - Recalibrate the input, if the problem persists,
the measurement of the analogue input check the wiring between the TCON and the
function connected to analogue input 0 will device connected to this analog input.
be affected. - Check installation and operation of the device
This may result in reduced operation of the connected.
Lamp Status Depending On analogue input C1 (ANIC1): Data Valid but Below Normal vehicle, the TCON action depends on Contact maintenance for troubleshooting or The measured value of the analog input is - refer to the other reported errors to identify
35.01 520211 1 Corresponding Functional Error Operational Range - Most Severe configured analog input fiunction Perform a calibration of the connected device. below the minimum allowed range. the affected analogue input function.
ERROR CODE
DANA [HEX] SAE J1939 DM 1 STATUS LAMP ERROR DESCRIPTION TCON ACTION DRIVER ACTION FAILURE CAUSE TROUBLESHOOTING
SPN FMI
TCON will continue normal operation but - Recalibrate the input, if the problem persists,
the measurement of the analogue input check the wiring between the TCON and the
function connected to analogue input 0 will device connected to this analog input.
be affected. - Check installation and operation of the device
This may result in reduced operation of the connected.
Lamp Status Depending On analogue input C2 (ANIC2): Data Valid but Above Normal vehicle, the TCON action depends on Contact maintenance for troubleshooting or The measured value of the analog input is - refer to the other reported errors to identify
36.00 520212 0 Corresponding Functional Error Operational Range - Most Severe configured analog input fiunction Perform a calibration of the connected device. above the maximum allowed range. the affected analogue input function.
TCON will continue normal operation but - Recalibrate the input, if the problem persists,
the measurement of the analogue input check the wiring between the TCON and the
function connected to analogue input 0 will device connected to this analog input.
be affected. - Check installation and operation of the device
This may result in reduced operation of the connected.
Lamp Status Depending On analogue input C2 (ANIC2): Data Valid but Below Normal vehicle, the TCON action depends on Contact maintenance for troubleshooting or The measured value of the analog input is - refer to the other reported errors to identify
36.01 520212 1 Corresponding Functional Error Operational Range - Most Severe configured analog input fiunction Perform a calibration of the connected device. below the minimum allowed range. the affected analogue input function.
ERROR CODE
DANA [HEX] SAE J1939 DM 1 STATUS LAMP ERROR DESCRIPTION TCON ACTION DRIVER ACTION FAILURE CAUSE TROUBLESHOOTING
SPN FMI
TCON will continue normal operation but - Recalibrate the input, if the problem persists,
the measurement of the analogue input check the wiring between the TCON and the
function connected to analogue input 0 will device connected to this analog input.
be affected. - Check installation and operation of the device
This may result in reduced operation of the connected.
Lamp Status Depending On analogue input C3 (ANIC3): Data Valid but Above Normal vehicle, the TCON action depends on Contact maintenance for troubleshooting or The measured value of the analog input is - refer to the other reported errors to identify
37.00 520213 0 Corresponding Functional Error Operational Range - Most Severe configured analog input fiunction Perform a calibration of the connected device. above the maximum allowed range. the affected analogue input function.
TCON will continue normal operation but - Recalibrate the input, if the problem persists,
the measurement of the analogue input check the wiring between the TCON and the
function connected to analogue input 0 will device connected to this analog input.
be affected. - Check installation and operation of the device
This may result in reduced operation of the connected.
Lamp Status Depending On analogue input C3 (ANIC3): Data Valid but Below Normal vehicle, the TCON action depends on Contact maintenance for troubleshooting or The measured value of the analog input is - refer to the other reported errors to identify
37.01 520213 1 Corresponding Functional Error Operational Range - Most Severe configured analog input fiunction Perform a calibration of the connected device. below the minimum allowed range. the affected analogue input function.
ERROR CODE
DANA [HEX] SAE J1939 DM 1 STATUS LAMP ERROR DESCRIPTION TCON ACTION DRIVER ACTION FAILURE CAUSE TROUBLESHOOTING
SPN FMI
TCON will continue normal operation but - Recalibrate the input, if the problem persists,
the measurement of the analogue input check the wiring between the TCON and the
function connected to analogue input 0 will device connected to this analog input.
be affected. - Check installation and operation of the device
This may result in reduced operation of the connected.
Lamp Status Depending On analogue input C4 (ANIC4): Data Valid but Above Normal vehicle, the TCON action depends on Contact maintenance for troubleshooting or The measured value of the analog input is - refer to the other reported errors to identify
38.00 520214 0 Corresponding Functional Error Operational Range - Most Severe configured analog input fiunction Perform a calibration of the connected device. above the maximum allowed range. the affected analogue input function.
TCON will continue normal operation but - Recalibrate the input, if the problem persists,
the measurement of the analogue input check the wiring between the TCON and the
function connected to analogue input 0 will device connected to this analog input.
be affected. - Check installation and operation of the device
This may result in reduced operation of the connected.
Lamp Status Depending On analogue input C4 (ANIC4): Data Valid but Below Normal vehicle, the TCON action depends on Contact maintenance for troubleshooting or The measured value of the analog input is - refer to the other reported errors to identify
38.01 520214 1 Corresponding Functional Error Operational Range - Most Severe configured analog input fiunction Perform a calibration of the connected device. below the minimum allowed range. the affected analogue input function.
ERROR CODE
DANA [HEX] SAE J1939 DM 1 STATUS LAMP ERROR DESCRIPTION TCON ACTION DRIVER ACTION FAILURE CAUSE TROUBLESHOOTING
SPN FMI
TCON will continue normal operation but - Recalibrate the input, if the problem persists,
the measurement of the analogue input check the wiring between the TCON and the
function connected to analogue input A0 device connected to this analog input.
will be affected. - Check installation and operation of the device
This may result in reduced operation of the connected.
Lamp Status Depending On analogue input A0 (ANIA0): Data Valid but Above Normal vehicle, the TCON action depends on Contact maintenance for troubleshooting or The measured value of the analog input is - refer to the other reported errors to identify
3B.00 520217 0 Corresponding Functional Error Operational Range - Most Severe configured analog input fiunction Perform a calibration of the connected device. above the maximum allowed range. the affected analogue input function.
TCON will continue normal operation but - Recalibrate the input, if the problem persists,
the measurement of the analogue input check the wiring between the TCON and the
function connected to analogue input A0 device connected to this analog input.
will be affected. - Check installation and operation of the device
This may result in reduced operation of the connected.
Lamp Status Depending On analogue input A0 (ANIA0): Data Valid but Below Normal vehicle, the TCON action depends on Contact maintenance for troubleshooting or The measured value of the analog input is - refer to the other reported errors to identify
3B.01 520217 1 Corresponding Functional Error Operational Range - Most Severe configured analog input fiunction Perform a calibration of the connected device. below the minimum allowed range. the affected analogue input function.
This message is given as additional The transmission ratio measured by the Check the transmission, in order to understand
Lamp Status Depending On Speed input 0: Data Valid but Above Normal Operational information for transmission ratio faults. Contact maintenance for troubleshooting controller is more than 5% below the value if and which clutch is slipping. Check the
3C.00 520218 0 Corresponding Functional Error Range - Most Severe The action is taken by ratio fault monitoring. of what is should be. transmission ratio settings of the controller.
This message is given as additional The transmission ratio measured by the Check the transmission, in order to understand
Lamp Status Depending On Speed input 0: Data Valid but Below Normal Operational information for transmission ratio faults. Contact maintenance for troubleshooting controller is more than 5% above the value if and which clutch is slipping. Check the
3C.01 520218 1 Corresponding Functional Error Range - Most Severe The action is taken by ratio fault monitoring. of what is should be. transmission ratio settings of the controller.
Contact maintenance for troubleshooting Direction reporting error of the speed - Check the speed sensor
3C.02 520218 2 Stop Lamp Solid Speed input 0: Data Erratic, Intermittent, or Incorrect TCON will revert to limphome mode. sensor. - Check the wiring of the speed sensor
TCON ERROR CODES & DESCRIPTIONS
Revision 2.54 - Firmware Version 2.04
Date: 3/3/2021
ERROR CODE
DANA [HEX] SAE J1939 DM 1 STATUS LAMP ERROR DESCRIPTION TCON ACTION DRIVER ACTION FAILURE CAUSE TROUBLESHOOTING
SPN FMI
This message is given as additional The transmission ratio measured by the Check the transmission, in order to understand
Lamp Status Depending On Speed input 1: Data Valid but Above Normal Operational information for transmission ratio faults. Contact maintenance for troubleshooting controller is more than 5% below the value if and which clutch is slipping. Check the
3D.00 520219 0 Corresponding Functional Error Range - Most Severe The action is taken by ratio fault monitoring. of what is should be. transmission ratio settings of the controller.
This message is given as additional The transmission ratio measured by the Check the transmission, in order to understand
Lamp Status Depending On Speed input 1: Data Valid but Below Normal Operational information for transmission ratio faults. Contact maintenance for troubleshooting controller is more than 5% above the value if and which clutch is slipping. Check the
3D.01 520219 1 Corresponding Functional Error Range - Most Severe The action is taken by ratio fault monitoring. of what is should be. transmission ratio settings of the controller.
Contact maintenance for troubleshooting Direction reporting error of the speed - Check the speed sensor
3D.02 520219 2 Stop Lamp Solid Speed input 1: Data Erratic, Intermittent, or Incorrect TCON will revert to limphome mode. sensor. - Check the wiring of the speed sensor
This message is given as additional The transmission ratio measured by the Check the transmission, in order to understand
Lamp Status Depending On Speed input 2: Data Valid but Above Normal Operational information for transmission ratio faults. Contact maintenance for troubleshooting controller is more than 5% below the value if and which clutch is slipping. Check the
3E.00 520220 0 Corresponding Functional Error Range - Most Severe The action is taken by ratio fault monitoring. of what is should be. transmission ratio settings of the controller.
This message is given as additional The transmission ratio measured by the Check the transmission, in order to understand
Lamp Status Depending On Speed input 2: Data Valid but Below Normal Operational information for transmission ratio faults. Contact maintenance for troubleshooting controller is more than 5% above the value if and which clutch is slipping. Check the
3E.01 520220 1 Corresponding Functional Error Range - Most Severe The action is taken by ratio fault monitoring. of what is should be. transmission ratio settings of the controller.
Contact maintenance for troubleshooting Direction reporting error of the speed - Check the speed sensor
3E.02 520220 2 Stop Lamp Solid Speed input 2: Data Erratic, Intermittent, or Incorrect TCON will revert to limphome mode. sensor. - Check the wiring of the speed sensor
ERROR CODE
DANA [HEX] SAE J1939 DM 1 STATUS LAMP ERROR DESCRIPTION TCON ACTION DRIVER ACTION FAILURE CAUSE TROUBLESHOOTING
SPN FMI
This message is given as additional The transmission ratio measured by the Check the transmission, in order to understand
Lamp Status Depending On Speed input 3: Data Valid but Above Normal Operational information for transmission ratio faults. Contact maintenance for troubleshooting controller is more than 5% below the value if and which clutch is slipping. Check the
3F.00 520221 0 Corresponding Functional Error Range - Most Severe The action is taken by ratio fault monitoring. of what is should be. transmission ratio settings of the controller.
This message is given as additional The transmission ratio measured by the Check the transmission, in order to understand
Lamp Status Depending On Speed input 3: Data Valid but Below Normal Operational information for transmission ratio faults. Contact maintenance for troubleshooting controller is more than 5% above the value if and which clutch is slipping. Check the
3F.01 520221 1 Corresponding Functional Error Range - Most Severe The action is taken by ratio fault monitoring. of what is should be. transmission ratio settings of the controller.
Contact maintenance for troubleshooting Direction reporting error of the speed - Check the speed sensor
3F.02 520221 2 Stop Lamp Solid Speed input 3: Data Erratic, Intermittent, or Incorrect TCON will revert to limphome mode. sensor. - Check the wiring of the speed sensor
In transmission shutdown mode, the driver can - Check the wiring between the TCON and the
If the output has a critical transmission no longer operate the vehicle. Return to a device connected to this analog output.
control function assigned to it, TCON will service center for troubleshooting as soon as - Check installation and operation of the
revert to transmission shutdown mode. posible. connected actuator.
In all other cases the assigned function In all other cases disabling the assigned function Dynamic checking by the TCON of the - refer to the other reported errors to get more
Lamp Status Depending On Analog Output 0: Voltage Above Normal, or Shorted To control will be disabled, possibly resulting in control will result in reduced vehicle operation. analog output detected that the output is information about the configured output
46.03 520224 3 Corresponding Functional Error High Source reduced vehicle operation. Contact maintenance for troubleshooting. shorted to battery plus (high source). function.
In transmission limphome mode, the driver can - Check the wiring between the TCON and the
If the output has a critical transmission still operate the vehicle (reduced vehicle device connected to this analog output.
control function assigned to it, TCON will operation). Return to a service center for - Check installation and operation of the
revert to transmission limphome mode. troubleshooting as soon as posible. connected actuator.
In any case the assigned function control In all other cases disabling the assigned function Dynamic checking by the TCON of the - refer to the other reported errors to get more
Lamp Status Depending On Analog Output 0: Voltage Below Normal, or Shorted To will be disabled, possibly resulting in control will result in reduced vehicle operation. output detected that the output is shorted information about the configured output
46.04 520224 4 Corresponding Functional Error Low Source reduced vehicle operation. Contact maintenance for troubleshooting. to ground (low source). function.
In transmission limphome mode, the driver can - Check the wiring between the TCON and the
If the output has a critical transmission still operate the vehicle (reduced vehicle device connected to this analog output.
control function assigned to it, TCON will operation). Return to a service center for - Check installation and operation of the
revert to transmission limphome mode. troubleshooting as soon as posible. connected actuator.
In any case the assigned function control In all other cases disabling the assigned function Dynamic checking by the TCON of the - refer to the other reported errors to get more
Lamp Status Depending On will be disabled, possibly resulting in control will result in reduced vehicle operation. analog output detected the output is in information about the configured output
46.05 520224 5 Corresponding Functional Error Analog Output 0: Current Below Normal, or Open Circuit reduced vehicle operation. Contact maintenance for troubleshooting. open circuit (loose connection). function.
TCON ERROR CODES & DESCRIPTIONS
Revision 2.54 - Firmware Version 2.04
Date: 3/3/2021
ERROR CODE
DANA [HEX] SAE J1939 DM 1 STATUS LAMP ERROR DESCRIPTION TCON ACTION DRIVER ACTION FAILURE CAUSE TROUBLESHOOTING
SPN FMI
In transmission shutdown mode, the driver can - Check the wiring between the TCON and the
If the output has a critical transmission no longer operate the vehicle. Return to a device connected to this analog output.
control function assigned to it, TCON will service center for troubleshooting as soon as - Check installation and operation of the
revert to transmission shutdown mode. posible. connected actuator.
In all other cases the assigned function In all other cases disabling the assigned function - refer to the other reported errors to get more
Lamp Status Depending On Analog Output 0: Current Above Normal or Grounded control will be disabled, possibly resulting in control will result in reduced vehicle operation. Dynamic checking by the TCON ofthe analog information about the configured output
46.06 520224 6 Corresponding Functional Error Circuit reduced vehicle operation. Contact maintenance for troubleshooting. output detected an overcurrent. function.
In transmission limphome mode, the driver can - Check the wiring between the TCON and the
If the output has a critical transmission still operate the vehicle (reduced vehicle device connected to this analog output.
control function assigned to it, TCON will operation). Return to a service center for - Check installation and operation of the
revert to transmission limphome mode. troubleshooting as soon as posible. connected actuator.
In any case the assigned function control In all other cases disabling the assigned function The TCON detected that the output current - refer to the other reported errors to get more
Lamp Status Depending On Analog Output 0: Abnormal Frequency or Pulse Width or will be disabled, possibly resulting in control will result in reduced vehicle operation. is out of range. This occurs when the load information about the configured output
46.08 520224 8 Corresponding Functional Error Period reduced vehicle operation. Contact maintenance for troubleshooting. has an incorrect impedance. function.
In transmission shutdown mode, the driver can - Check the wiring between the TCON and the
If the output has a critical transmission no longer operate the vehicle. Return to a device connected to this analog output.
control function assigned to it, TCON will service center for troubleshooting as soon as - Check installation and operation of the
revert to transmission shutdown mode. posible. connected actuator.
In all other cases the assigned function In all other cases disabling the assigned function Dynamic checking by the TCON of the - refer to the other reported errors to get more
Lamp Status Depending On Analog Output 1: Voltage Above Normal, or Shorted To control will be disabled, possibly resulting in control will result in reduced vehicle operation. analog output detected that the output is information about the configured output
47.03 520225 3 Corresponding Functional Error High Source reduced vehicle operation. Contact maintenance for troubleshooting. shorted to battery plus (high source). function.
In transmission limphome mode, the driver can - Check the wiring between the TCON and the
If the output has a critical transmission still operate the vehicle (reduced vehicle device connected to this analog output.
control function assigned to it, TCON will operation). Return to a service center for - Check installation and operation of the
revert to transmission limphome mode. troubleshooting as soon as posible. connected actuator.
In any case the assigned function control In all other cases disabling the assigned function Dynamic checking by the TCON of the - refer to the other reported errors to get more
Lamp Status Depending On Analog Output 1: Voltage Below Normal, or Shorted To will be disabled, possibly resulting in control will result in reduced vehicle operation. output detected that the output is shorted information about the configured output
47.04 520225 4 Corresponding Functional Error Low Source reduced vehicle operation. Contact maintenance for troubleshooting. to ground (low source). function.
In transmission limphome mode, the driver can - Check the wiring between the TCON and the
If the output has a critical transmission still operate the vehicle (reduced vehicle device connected to this analog output.
control function assigned to it, TCON will operation). Return to a service center for - Check installation and operation of the
revert to transmission limphome mode. troubleshooting as soon as posible. connected actuator.
In any case the assigned function control In all other cases disabling the assigned function Dynamic checking by the TCON of the - refer to the other reported errors to get more
Lamp Status Depending On will be disabled, possibly resulting in control will result in reduced vehicle operation. analog output detected the output is in information about the configured output
47.05 520225 5 Corresponding Functional Error Analog Output 1: Current Below Normal, or Open Circuit reduced vehicle operation. Contact maintenance for troubleshooting. open circuit (loose connection). function.
In transmission shutdown mode, the driver can - Check the wiring between the TCON and the
If the output has a critical transmission no longer operate the vehicle. Return to a device connected to this analog output.
control function assigned to it, TCON will service center for troubleshooting as soon as - Check installation and operation of the
revert to transmission shutdown mode. posible. connected actuator.
In all other cases the assigned function In all other cases disabling the assigned function - refer to the other reported errors to get more
Lamp Status Depending On Analog Output 1: Current Above Normal or Grounded control will be disabled, possibly resulting in control will result in reduced vehicle operation. Dynamic checking by the TCON ofthe analog information about the configured output
47.06 520225 6 Corresponding Functional Error Circuit reduced vehicle operation. Contact maintenance for troubleshooting. output detected an overcurrent. function.
TCON ERROR CODES & DESCRIPTIONS
Revision 2.54 - Firmware Version 2.04
Date: 3/3/2021
ERROR CODE
DANA [HEX] SAE J1939 DM 1 STATUS LAMP ERROR DESCRIPTION TCON ACTION DRIVER ACTION FAILURE CAUSE TROUBLESHOOTING
SPN FMI
In transmission limphome mode, the driver can - Check the wiring between the TCON and the
If the output has a critical transmission still operate the vehicle (reduced vehicle device connected to this analog output.
control function assigned to it, TCON will operation). Return to a service center for - Check installation and operation of the
revert to transmission limphome mode. troubleshooting as soon as posible. connected actuator.
In any case the assigned function control In all other cases disabling the assigned function The TCON detected that the output current - refer to the other reported errors to get more
Lamp Status Depending On Analog Output 1: Abnormal Frequency or Pulse Width or will be disabled, possibly resulting in control will result in reduced vehicle operation. is out of range. This occurs when the load information about the configured output
47.08 520225 8 Corresponding Functional Error Period reduced vehicle operation. Contact maintenance for troubleshooting. has an incorrect impedance. function.
In transmission shutdown mode, the driver can - Check the wiring between the TCON and the
If the output has a critical transmission no longer operate the vehicle. Return to a device connected to this analog output.
control function assigned to it, TCON will service center for troubleshooting as soon as - Check installation and operation of the
revert to transmission shutdown mode. posible. connected actuator.
In all other cases the assigned function In all other cases disabling the assigned function Dynamic checking by the TCON of the - refer to the other reported errors to get more
Lamp Status Depending On Analog Output 2: Voltage Above Normal, or Shorted To control will be disabled, possibly resulting in control will result in reduced vehicle operation. analog output detected that the output is information about the configured output
48.03 520226 3 Corresponding Functional Error High Source reduced vehicle operation. Contact maintenance for troubleshooting. shorted to battery plus (high source). function.
In transmission limphome mode, the driver can - Check the wiring between the TCON and the
If the output has a critical transmission still operate the vehicle (reduced vehicle device connected to this analog output.
control function assigned to it, TCON will operation). Return to a service center for - Check installation and operation of the
revert to transmission limphome mode. troubleshooting as soon as posible. connected actuator.
In any case the assigned function control In all other cases disabling the assigned function Dynamic checking by the TCON of the - refer to the other reported errors to get more
Lamp Status Depending On Analog Output 2: Voltage Below Normal, or Shorted To will be disabled, possibly resulting in control will result in reduced vehicle operation. output detected that the output is shorted information about the configured output
48.04 520226 4 Corresponding Functional Error Low Source reduced vehicle operation. Contact maintenance for troubleshooting. to ground (low source). function.
In transmission limphome mode, the driver can - Check the wiring between the TCON and the
If the output has a critical transmission still operate the vehicle (reduced vehicle device connected to this analog output.
control function assigned to it, TCON will operation). Return to a service center for - Check installation and operation of the
revert to transmission limphome mode. troubleshooting as soon as posible. connected actuator.
In any case the assigned function control In all other cases disabling the assigned function Dynamic checking by the TCON of the - refer to the other reported errors to get more
Lamp Status Depending On will be disabled, possibly resulting in control will result in reduced vehicle operation. analog output detected the output is in information about the configured output
48.05 520226 5 Corresponding Functional Error Analog Output 2: Current Below Normal, or Open Circuit reduced vehicle operation. Contact maintenance for troubleshooting. open circuit (loose connection). function.
In transmission shutdown mode, the driver can - Check the wiring between the TCON and the
If the output has a critical transmission no longer operate the vehicle. Return to a device connected to this analog output.
control function assigned to it, TCON will service center for troubleshooting as soon as - Check installation and operation of the
revert to transmission shutdown mode. posible. connected actuator.
In all other cases the assigned function In all other cases disabling the assigned function - refer to the other reported errors to get more
Lamp Status Depending On Analog Output 2: Current Above Normal or Grounded control will be disabled, possibly resulting in control will result in reduced vehicle operation. Dynamic checking by the TCON ofthe analog information about the configured output
48.06 520226 6 Corresponding Functional Error Circuit reduced vehicle operation. Contact maintenance for troubleshooting. output detected an overcurrent. function.
In transmission limphome mode, the driver can - Check the wiring between the TCON and the
If the output has a critical transmission still operate the vehicle (reduced vehicle device connected to this analog output.
control function assigned to it, TCON will operation). Return to a service center for - Check installation and operation of the
revert to transmission limphome mode. troubleshooting as soon as posible. connected actuator.
In any case the assigned function control In all other cases disabling the assigned function The TCON detected that the output current - refer to the other reported errors to get more
Lamp Status Depending On Analog Output 2: Abnormal Frequency or Pulse Width or will be disabled, possibly resulting in control will result in reduced vehicle operation. is out of range. This occurs when the load information about the configured output
48.08 520226 8 Corresponding Functional Error Period reduced vehicle operation. Contact maintenance for troubleshooting. has an incorrect impedance. function.
TCON ERROR CODES & DESCRIPTIONS
Revision 2.54 - Firmware Version 2.04
Date: 3/3/2021
ERROR CODE
DANA [HEX] SAE J1939 DM 1 STATUS LAMP ERROR DESCRIPTION TCON ACTION DRIVER ACTION FAILURE CAUSE TROUBLESHOOTING
SPN FMI
In transmission shutdown mode, the driver can - Check the wiring between the TCON and the
If the output has a critical transmission no longer operate the vehicle. Return to a device connected to this analog output.
control function assigned to it, TCON will service center for troubleshooting as soon as - Check installation and operation of the
revert to transmission shutdown mode. posible. connected actuator.
In all other cases the assigned function In all other cases disabling the assigned function Dynamic checking by the TCON of the - refer to the other reported errors to get more
Lamp Status Depending On Analog Output 3: Voltage Above Normal, or Shorted To control will be disabled, possibly resulting in control will result in reduced vehicle operation. analog output detected that the output is information about the configured output
49.03 520227 3 Corresponding Functional Error High Source reduced vehicle operation. Contact maintenance for troubleshooting. shorted to battery plus (high source). function.
In transmission limphome mode, the driver can - Check the wiring between the TCON and the
If the output has a critical transmission still operate the vehicle (reduced vehicle device connected to this analog output.
control function assigned to it, TCON will operation). Return to a service center for - Check installation and operation of the
revert to transmission limphome mode. troubleshooting as soon as posible. connected actuator.
In any case the assigned function control In all other cases disabling the assigned function Dynamic checking by the TCON of the - refer to the other reported errors to get more
Lamp Status Depending On Analog Output 3: Voltage Below Normal, or Shorted To will be disabled, possibly resulting in control will result in reduced vehicle operation. output detected that the output is shorted information about the configured output
49.04 520227 4 Corresponding Functional Error Low Source reduced vehicle operation. Contact maintenance for troubleshooting. to ground (low source). function.
In transmission limphome mode, the driver can - Check the wiring between the TCON and the
If the output has a critical transmission still operate the vehicle (reduced vehicle device connected to this analog output.
control function assigned to it, TCON will operation). Return to a service center for - Check installation and operation of the
revert to transmission limphome mode. troubleshooting as soon as posible. connected actuator.
In any case the assigned function control In all other cases disabling the assigned function Dynamic checking by the TCON of the - refer to the other reported errors to get more
Lamp Status Depending On will be disabled, possibly resulting in control will result in reduced vehicle operation. analog output detected the output is in information about the configured output
49.05 520227 5 Corresponding Functional Error Analog Output 3: Current Below Normal, or Open Circuit reduced vehicle operation. Contact maintenance for troubleshooting. open circuit (loose connection). function.
In transmission shutdown mode, the driver can - Check the wiring between the TCON and the
If the output has a critical transmission no longer operate the vehicle. Return to a device connected to this analog output.
control function assigned to it, TCON will service center for troubleshooting as soon as - Check installation and operation of the
revert to transmission shutdown mode. posible. connected actuator.
In all other cases the assigned function In all other cases disabling the assigned function - refer to the other reported errors to get more
Lamp Status Depending On Analog Output 3: Current Above Normal or Grounded control will be disabled, possibly resulting in control will result in reduced vehicle operation. Dynamic checking by the TCON ofthe analog information about the configured output
49.06 520227 6 Corresponding Functional Error Circuit reduced vehicle operation. Contact maintenance for troubleshooting. output detected an overcurrent. function.
In transmission limphome mode, the driver can - Check the wiring between the TCON and the
If the output has a critical transmission still operate the vehicle (reduced vehicle device connected to this analog output.
control function assigned to it, TCON will operation). Return to a service center for - Check installation and operation of the
revert to transmission limphome mode. troubleshooting as soon as posible. connected actuator.
In any case the assigned function control In all other cases disabling the assigned function The TCON detected that the output current - refer to the other reported errors to get more
Lamp Status Depending On Analog Output 3: Abnormal Frequency or Pulse Width or will be disabled, possibly resulting in control will result in reduced vehicle operation. is out of range. This occurs when the load information about the configured output
49.08 520227 8 Corresponding Functional Error Period reduced vehicle operation. Contact maintenance for troubleshooting. has an incorrect impedance. function.
In transmission shutdown mode, the driver can - Check the wiring between the TCON and the
If the output has a critical transmission no longer operate the vehicle. Return to a device connected to this analog output.
control function assigned to it, TCON will service center for troubleshooting as soon as - Check installation and operation of the
revert to transmission shutdown mode. posible. connected actuator.
In all other cases the assigned function In all other cases disabling the assigned function Dynamic checking by the TCON of the - refer to the other reported errors to get more
Lamp Status Depending On Analog Output 4: Voltage Above Normal, or Shorted To control will be disabled, possibly resulting in control will result in reduced vehicle operation. analog output detected that the output is information about the configured output
4A.03 520228 3 Corresponding Functional Error High Source reduced vehicle operation. Contact maintenance for troubleshooting. shorted to battery plus (high source). function.
TCON ERROR CODES & DESCRIPTIONS
Revision 2.54 - Firmware Version 2.04
Date: 3/3/2021
ERROR CODE
DANA [HEX] SAE J1939 DM 1 STATUS LAMP ERROR DESCRIPTION TCON ACTION DRIVER ACTION FAILURE CAUSE TROUBLESHOOTING
SPN FMI
In transmission limphome mode, the driver can - Check the wiring between the TCON and the
If the output has a critical transmission still operate the vehicle (reduced vehicle device connected to this analog output.
control function assigned to it, TCON will operation). Return to a service center for - Check installation and operation of the
revert to transmission limphome mode. troubleshooting as soon as posible. connected actuator.
In any case the assigned function control In all other cases disabling the assigned function Dynamic checking by the TCON of the - refer to the other reported errors to get more
Lamp Status Depending On Analog Output 4: Voltage Below Normal, or Shorted To will be disabled, possibly resulting in control will result in reduced vehicle operation. output detected that the output is shorted information about the configured output
4A.04 520228 4 Corresponding Functional Error Low Source reduced vehicle operation. Contact maintenance for troubleshooting. to ground (low source). function.
In transmission limphome mode, the driver can - Check the wiring between the TCON and the
If the output has a critical transmission still operate the vehicle (reduced vehicle device connected to this analog output.
control function assigned to it, TCON will operation). Return to a service center for - Check installation and operation of the
revert to transmission limphome mode. troubleshooting as soon as posible. connected actuator.
In any case the assigned function control In all other cases disabling the assigned function Dynamic checking by the TCON of the - refer to the other reported errors to get more
Lamp Status Depending On will be disabled, possibly resulting in control will result in reduced vehicle operation. analog output detected the output is in information about the configured output
4A.05 520228 5 Corresponding Functional Error Analog Output 4: Current Below Normal, or Open Circuit reduced vehicle operation. Contact maintenance for troubleshooting. open circuit (loose connection). function.
In transmission shutdown mode, the driver can - Check the wiring between the TCON and the
If the output has a critical transmission no longer operate the vehicle. Return to a device connected to this analog output.
control function assigned to it, TCON will service center for troubleshooting as soon as - Check installation and operation of the
revert to transmission shutdown mode. posible. connected actuator.
In all other cases the assigned function In all other cases disabling the assigned function - refer to the other reported errors to get more
Lamp Status Depending On Analog Output 4: Current Above Normal or Grounded control will be disabled, possibly resulting in control will result in reduced vehicle operation. Dynamic checking by the TCON ofthe analog information about the configured output
4A.06 520228 6 Corresponding Functional Error Circuit reduced vehicle operation. Contact maintenance for troubleshooting. output detected an overcurrent. function.
In transmission limphome mode, the driver can - Check the wiring between the TCON and the
If the output has a critical transmission still operate the vehicle (reduced vehicle device connected to this analog output.
control function assigned to it, TCON will operation). Return to a service center for - Check installation and operation of the
revert to transmission limphome mode. troubleshooting as soon as posible. connected actuator.
In any case the assigned function control In all other cases disabling the assigned function The TCON detected that the output current - refer to the other reported errors to get more
Lamp Status Depending On Analog Output 4: Abnormal Frequency or Pulse Width or will be disabled, possibly resulting in control will result in reduced vehicle operation. is out of range. This occurs when the load information about the configured output
4A.08 520228 8 Corresponding Functional Error Period reduced vehicle operation. Contact maintenance for troubleshooting. has an incorrect impedance. function.
ERROR CODE
DANA [HEX] SAE J1939 DM 1 STATUS LAMP ERROR DESCRIPTION TCON ACTION DRIVER ACTION FAILURE CAUSE TROUBLESHOOTING
SPN FMI
In transmission shutdown mode, the driver can - Check the wiring between the TCON and the
If the output has a critical transmission no longer operate the vehicle. Return to a device connected to this analog output.
control function assigned to it, TCON will service center for troubleshooting as soon as - Check installation and operation of the
revert to transmission shutdown mode. posible. connected actuator.
In all other cases the assigned function In all other cases disabling the assigned function Dynamic checking by the TCON of the - refer to the other reported errors to get more
Lamp Status Depending On Analog Output 5: Voltage Above Normal, or Shorted To control will be disabled, possibly resulting in control will result in reduced vehicle operation. analog output detected that the output is information about the configured output
4C.03 520230 3 Corresponding Functional Error High Source reduced vehicle operation. Contact maintenance for troubleshooting. shorted to battery plus (high source). function.
In transmission limphome mode, the driver can - Check the wiring between the TCON and the
If the output has a critical transmission still operate the vehicle (reduced vehicle device connected to this analog output.
control function assigned to it, TCON will operation). Return to a service center for - Check installation and operation of the
revert to transmission limphome mode. troubleshooting as soon as posible. connected actuator.
In any case the assigned function control In all other cases disabling the assigned function Dynamic checking by the TCON of the - refer to the other reported errors to get more
Lamp Status Depending On Analog Output 5: Voltage Below Normal, or Shorted To will be disabled, possibly resulting in control will result in reduced vehicle operation. output detected that the output is shorted information about the configured output
4C.04 520230 4 Corresponding Functional Error Low Source reduced vehicle operation. Contact maintenance for troubleshooting. to ground (low source). function.
In transmission limphome mode, the driver can - Check the wiring between the TCON and the
If the output has a critical transmission still operate the vehicle (reduced vehicle device connected to this analog output.
control function assigned to it, TCON will operation). Return to a service center for - Check installation and operation of the
revert to transmission limphome mode. troubleshooting as soon as posible. connected actuator.
In any case the assigned function control In all other cases disabling the assigned function Dynamic checking by the TCON of the - refer to the other reported errors to get more
Lamp Status Depending On will be disabled, possibly resulting in control will result in reduced vehicle operation. analog output detected the output is in information about the configured output
4C.05 520230 5 Corresponding Functional Error Analog Output 5: Current Below Normal, or Open Circuit reduced vehicle operation. Contact maintenance for troubleshooting. open circuit (loose connection). function.
In transmission shutdown mode, the driver can - Check the wiring between the TCON and the
If the output has a critical transmission no longer operate the vehicle. Return to a device connected to this analog output.
control function assigned to it, TCON will service center for troubleshooting as soon as - Check installation and operation of the
revert to transmission shutdown mode. posible. connected actuator.
In all other cases the assigned function In all other cases disabling the assigned function - refer to the other reported errors to get more
Lamp Status Depending On Analog Output 5: Current Above Normal or Grounded control will be disabled, possibly resulting in control will result in reduced vehicle operation. Dynamic checking by the TCON ofthe analog information about the configured output
4C.06 520230 6 Corresponding Functional Error Circuit reduced vehicle operation. Contact maintenance for troubleshooting. output detected an overcurrent. function.
In transmission limphome mode, the driver can - Check the wiring between the TCON and the
If the output has a critical transmission still operate the vehicle (reduced vehicle device connected to this analog output.
control function assigned to it, TCON will operation). Return to a service center for - Check installation and operation of the
revert to transmission limphome mode. troubleshooting as soon as posible. connected actuator.
In any case the assigned function control In all other cases disabling the assigned function The TCON detected that the output current - refer to the other reported errors to get more
Lamp Status Depending On Analog Output 5: Abnormal Frequency or Pulse Width or will be disabled, possibly resulting in control will result in reduced vehicle operation. is out of range. This occurs when the load information about the configured output
4C.08 520230 8 Corresponding Functional Error Period reduced vehicle operation. Contact maintenance for troubleshooting. has an incorrect impedance. function.
In transmission limphome mode, the driver can - Check the wiring between the TCON and the
If the output has a critical transmission still operate the vehicle (reduced vehicle device connected to this analog output.
control function assigned to it, TCON will operation). Return to a service center for - Check installation and operation of the
revert to transmission limphome mode. troubleshooting as soon as posible. connected actuator.
The assigned function can be blocked in the In all other cases disabling the assigned function Dynamic checking by the TCON of the digital - refer to the other reported errors to get more
Lamp Status Depending On High Side Output 0: Voltage Above Normal, or Shorted activated or deactivated state, possibly control will result in reduced vehicle operation. output detected the output is shorted to information about the configured output
50.03 520231 3 Corresponding Functional Error To High Source resulting in reduced vehicle operation. Contact maintenance for troubleshooting. battery plus (high source). function.
TCON ERROR CODES & DESCRIPTIONS
Revision 2.54 - Firmware Version 2.04
Date: 3/3/2021
ERROR CODE
DANA [HEX] SAE J1939 DM 1 STATUS LAMP ERROR DESCRIPTION TCON ACTION DRIVER ACTION FAILURE CAUSE TROUBLESHOOTING
SPN FMI
In transmission limphome mode, the driver can - Check the wiring between the TCON and the
If the output has a critical transmission still operate the vehicle (reduced vehicle device connected to this analog output.
control function assigned to it, TCON will operation). Return to a service center for - Check installation and operation of the
revert to transmission limphome mode. troubleshooting as soon as posible. Dynamic checking by the TCON of the digital connected actuator.
The assigned function can be blocked in the In all other cases disabling the assigned function output detected the output is shorted to - refer to the other reported errors to get more
Lamp Status Depending On High Side Output 0: Voltage Below Normal, or Shorted To activated or deactivated state, possibly control will result in reduced vehicle operation. ground (low source), or the actuator wires information about the configured output
50.04 520231 4 Corresponding Functional Error Low Source resulting in reduced vehicle operation. Contact maintenance for troubleshooting. are shorted to each other. function.
In transmission limphome mode, the driver can - Check the wiring between the TCON and the
If the output has a critical transmission still operate the vehicle (reduced vehicle device connected to this analog output.
control function assigned to it, TCON will operation). Return to a service center for - Check installation and operation of the
revert to transmission limphome mode. troubleshooting as soon as posible. connected actuator.
The assigned function can be blocked in the In all other cases disabling the assigned function Dynamic checking by the TCON of the - refer to the other reported errors to get more
Lamp Status Depending On High Side Output 0: Current Below Normal, or Open activated or deactivated state, possibly control will result in reduced vehicle operation. analog output detected the output is in information about the configured output
50.05 520231 5 Corresponding Functional Error Circuit resulting in reduced vehicle operation. Contact maintenance for troubleshooting. open circuit (loose connection). function.
In transmission limphome mode, the driver can - Check the wiring between the TCON and the
If the output has a critical transmission still operate the vehicle (reduced vehicle device connected to this analog output.
control function assigned to it, TCON will operation). Return to a service center for - Check installation and operation of the
revert to transmission limphome mode. troubleshooting as soon as posible. connected actuator.
The assigned function can be blocked in the In all other cases disabling the assigned function Dynamic checking by the TCON of the digital - refer to the other reported errors to get more
Lamp Status Depending On High Side Output 1: Voltage Above Normal, or Shorted activated or deactivated state, possibly control will result in reduced vehicle operation. output detected the output is shorted to information about the configured output
51.03 520232 3 Corresponding Functional Error To High Source resulting in reduced vehicle operation. Contact maintenance for troubleshooting. battery plus (high source). function.
In transmission limphome mode, the driver can - Check the wiring between the TCON and the
If the output has a critical transmission still operate the vehicle (reduced vehicle device connected to this analog output.
control function assigned to it, TCON will operation). Return to a service center for - Check installation and operation of the
revert to transmission limphome mode. troubleshooting as soon as posible. Dynamic checking by the TCON of the digital connected actuator.
The assigned function can be blocked in the In all other cases disabling the assigned function output detected the output is shorted to - refer to the other reported errors to get more
Lamp Status Depending On High Side Output 1: Voltage Below Normal, or Shorted To activated or deactivated state, possibly control will result in reduced vehicle operation. ground (low source), or the actuator wires information about the configured output
51.04 520232 4 Corresponding Functional Error Low Source resulting in reduced vehicle operation. Contact maintenance for troubleshooting. are shorted to each other. function.
In transmission limphome mode, the driver can - Check the wiring between the TCON and the
If the output has a critical transmission still operate the vehicle (reduced vehicle device connected to this analog output.
control function assigned to it, TCON will operation). Return to a service center for - Check installation and operation of the
revert to transmission limphome mode. troubleshooting as soon as posible. connected actuator.
The assigned function can be blocked in the In all other cases disabling the assigned function Dynamic checking by the TCON of the - refer to the other reported errors to get more
Lamp Status Depending On High Side Output 1: Current Below Normal, or Open activated or deactivated state, possibly control will result in reduced vehicle operation. analog output detected the output is in information about the configured output
51.05 520232 5 Corresponding Functional Error Circuit resulting in reduced vehicle operation. Contact maintenance for troubleshooting. open circuit (loose connection). function.
In transmission limphome mode, the driver can - Check the wiring between the TCON and the
If the output has a critical transmission still operate the vehicle (reduced vehicle device connected to this analog output.
control function assigned to it, TCON will operation). Return to a service center for - Check installation and operation of the
revert to transmission limphome mode. troubleshooting as soon as posible. connected actuator.
The assigned function can be blocked in the In all other cases disabling the assigned function Dynamic checking by the TCON of the digital - refer to the other reported errors to get more
Lamp Status Depending On High Side Output 2: Voltage Above Normal, or Shorted activated or deactivated state, possibly control will result in reduced vehicle operation. output detected the output is shorted to information about the configured output
52.03 520233 3 Corresponding Functional Error To High Source resulting in reduced vehicle operation. Contact maintenance for troubleshooting. battery plus (high source). function.
TCON ERROR CODES & DESCRIPTIONS
Revision 2.54 - Firmware Version 2.04
Date: 3/3/2021
ERROR CODE
DANA [HEX] SAE J1939 DM 1 STATUS LAMP ERROR DESCRIPTION TCON ACTION DRIVER ACTION FAILURE CAUSE TROUBLESHOOTING
SPN FMI
In transmission limphome mode, the driver can - Check the wiring between the TCON and the
If the output has a critical transmission still operate the vehicle (reduced vehicle device connected to this analog output.
control function assigned to it, TCON will operation). Return to a service center for - Check installation and operation of the
revert to transmission limphome mode. troubleshooting as soon as posible. Dynamic checking by the TCON of the digital connected actuator.
The assigned function can be blocked in the In all other cases disabling the assigned function output detected the output is shorted to - refer to the other reported errors to get more
Lamp Status Depending On High Side Output 2: Voltage Below Normal, or Shorted To activated or deactivated state, possibly control will result in reduced vehicle operation. ground (low source), or the actuator wires information about the configured output
52.04 520233 4 Corresponding Functional Error Low Source resulting in reduced vehicle operation. Contact maintenance for troubleshooting. are shorted to each other. function.
In transmission limphome mode, the driver can - Check the wiring between the TCON and the
If the output has a critical transmission still operate the vehicle (reduced vehicle device connected to this analog output.
control function assigned to it, TCON will operation). Return to a service center for - Check installation and operation of the
revert to transmission limphome mode. troubleshooting as soon as posible. connected actuator.
The assigned function can be blocked in the In all other cases disabling the assigned function Dynamic checking by the TCON of the - refer to the other reported errors to get more
Lamp Status Depending On High Side Output 2: Current Below Normal, or Open activated or deactivated state, possibly control will result in reduced vehicle operation. analog output detected the output is in information about the configured output
52.05 520233 5 Corresponding Functional Error Circuit resulting in reduced vehicle operation. Contact maintenance for troubleshooting. open circuit (loose connection). function.
In transmission limphome mode, the driver can - Check the wiring between the TCON and the
If the output has a critical transmission still operate the vehicle (reduced vehicle device connected to this analog output.
control function assigned to it, TCON will operation). Return to a service center for - Check installation and operation of the
revert to transmission limphome mode. troubleshooting as soon as posible. connected actuator.
The assigned function can be blocked in the In all other cases disabling the assigned function Dynamic checking by the TCON of the digital - refer to the other reported errors to get more
Lamp Status Depending On High Side Output 3: Voltage Above Normal, or Shorted activated or deactivated state, possibly control will result in reduced vehicle operation. output detected the output is shorted to information about the configured output
53.03 520234 3 Corresponding Functional Error To High Source resulting in reduced vehicle operation. Contact maintenance for troubleshooting. battery plus (high source). function.
In transmission limphome mode, the driver can - Check the wiring between the TCON and the
If the output has a critical transmission still operate the vehicle (reduced vehicle device connected to this analog output.
control function assigned to it, TCON will operation). Return to a service center for - Check installation and operation of the
revert to transmission limphome mode. troubleshooting as soon as posible. Dynamic checking by the TCON of the digital connected actuator.
The assigned function can be blocked in the In all other cases disabling the assigned function output detected the output is shorted to - refer to the other reported errors to get more
Lamp Status Depending On High Side Output 3: Voltage Below Normal, or Shorted To activated or deactivated state, possibly control will result in reduced vehicle operation. ground (low source), or the actuator wires information about the configured output
53.04 520234 4 Corresponding Functional Error Low Source resulting in reduced vehicle operation. Contact maintenance for troubleshooting. are shorted to each other. function.
In transmission limphome mode, the driver can - Check the wiring between the TCON and the
If the output has a critical transmission still operate the vehicle (reduced vehicle device connected to this analog output.
control function assigned to it, TCON will operation). Return to a service center for - Check installation and operation of the
revert to transmission limphome mode. troubleshooting as soon as posible. connected actuator.
The assigned function can be blocked in the In all other cases disabling the assigned function Dynamic checking by the TCON of the - refer to the other reported errors to get more
Lamp Status Depending On High Side Output 3: Current Below Normal, or Open activated or deactivated state, possibly control will result in reduced vehicle operation. analog output detected the output is in information about the configured output
53.05 520234 5 Corresponding Functional Error Circuit resulting in reduced vehicle operation. Contact maintenance for troubleshooting. open circuit (loose connection). function.
In transmission limphome mode, the driver can - Check the wiring between the TCON and the
If the output has a critical transmission still operate the vehicle (reduced vehicle device connected to this analog output.
control function assigned to it, TCON will operation). Return to a service center for - Check installation and operation of the
revert to transmission limphome mode. troubleshooting as soon as posible. connected actuator.
The assigned function can be blocked in the In all other cases disabling the assigned function Dynamic checking by the TCON of the digital - refer to the other reported errors to get more
Lamp Status Depending On Low Side Output 0: Voltage Above Normal, or Shorted To activated or deactivated state, possibly control will result in reduced vehicle operation. output detected the output is shorted to information about the configured output
54.03 520235 3 Corresponding Functional Error High Source resulting in reduced vehicle operation. Contact maintenance for troubleshooting. battery plus (high source). function.
TCON ERROR CODES & DESCRIPTIONS
Revision 2.54 - Firmware Version 2.04
Date: 3/3/2021
ERROR CODE
DANA [HEX] SAE J1939 DM 1 STATUS LAMP ERROR DESCRIPTION TCON ACTION DRIVER ACTION FAILURE CAUSE TROUBLESHOOTING
SPN FMI
In transmission limphome mode, the driver can - Check the wiring between the TCON and the
If the output has a critical transmission still operate the vehicle (reduced vehicle device connected to this analog output.
control function assigned to it, TCON will operation). Return to a service center for - Check installation and operation of the
revert to transmission limphome mode. troubleshooting as soon as posible. Dynamic checking by the TCON of the digital connected actuator.
The assigned function can be blocked in the In all other cases disabling the assigned function output detected the output is shorted to - refer to the other reported errors to get more
Lamp Status Depending On Low Side Output 0: Voltage Below Normal, or Shorted To activated or deactivated state, possibly control will result in reduced vehicle operation. ground (low source), or the actuator wires information about the configured output
54.04 520235 4 Corresponding Functional Error Low Source resulting in reduced vehicle operation. Contact maintenance for troubleshooting. are shorted to each other. function.
In transmission limphome mode, the driver can - Check the wiring between the TCON and the
If the output has a critical transmission still operate the vehicle (reduced vehicle device connected to this analog output.
control function assigned to it, TCON will operation). Return to a service center for - Check installation and operation of the
revert to transmission limphome mode. troubleshooting as soon as posible. connected actuator.
The assigned function can be blocked in the In all other cases disabling the assigned function Dynamic checking by the TCON of the - refer to the other reported errors to get more
Lamp Status Depending On Low Side Output 0: Current Below Normal, or Open activated or deactivated state, possibly control will result in reduced vehicle operation. analog output detected the output is in information about the configured output
54.05 520235 5 Corresponding Functional Error Circuit resulting in reduced vehicle operation. Contact maintenance for troubleshooting. open circuit (loose connection). function.
In transmission limphome mode, the driver can - Check the wiring between the TCON and the
If the output has a critical transmission still operate the vehicle (reduced vehicle device connected to this analog output.
control function assigned to it, TCON will operation). Return to a service center for - Check installation and operation of the
revert to transmission limphome mode. troubleshooting as soon as posible. connected actuator.
The assigned function can be blocked in the In all other cases disabling the assigned function Dynamic checking by the TCON of the digital - refer to the other reported errors to get more
Lamp Status Depending On Low Side Output 1: Voltage Above Normal, or Shorted To activated or deactivated state, possibly control will result in reduced vehicle operation. output detected the output is shorted to information about the configured output
55.03 520236 3 Corresponding Functional Error High Source resulting in reduced vehicle operation. Contact maintenance for troubleshooting. battery plus (high source). function.
In transmission limphome mode, the driver can - Check the wiring between the TCON and the
If the output has a critical transmission still operate the vehicle (reduced vehicle device connected to this analog output.
control function assigned to it, TCON will operation). Return to a service center for - Check installation and operation of the
revert to transmission limphome mode. troubleshooting as soon as posible. Dynamic checking by the TCON of the digital connected actuator.
The assigned function can be blocked in the In all other cases disabling the assigned function output detected the output is shorted to - refer to the other reported errors to get more
Lamp Status Depending On Low Side Output 1: Voltage Below Normal, or Shorted To activated or deactivated state, possibly control will result in reduced vehicle operation. ground (low source), or the actuator wires information about the configured output
55.04 520236 4 Corresponding Functional Error Low Source resulting in reduced vehicle operation. Contact maintenance for troubleshooting. are shorted to each other. function.
In transmission limphome mode, the driver can - Check the wiring between the TCON and the
If the output has a critical transmission still operate the vehicle (reduced vehicle device connected to this analog output.
control function assigned to it, TCON will operation). Return to a service center for - Check installation and operation of the
revert to transmission limphome mode. troubleshooting as soon as posible. connected actuator.
The assigned function can be blocked in the In all other cases disabling the assigned function Dynamic checking by the TCON of the - refer to the other reported errors to get more
Lamp Status Depending On Low Side Output 1: Current Below Normal, or Open activated or deactivated state, possibly control will result in reduced vehicle operation. analog output detected the output is in information about the configured output
55.05 520236 5 Corresponding Functional Error Circuit resulting in reduced vehicle operation. Contact maintenance for troubleshooting. open circuit (loose connection). function.
In transmission limphome mode, the driver can - Check the wiring between the TCON and the
If the output has a critical transmission still operate the vehicle (reduced vehicle device connected to this analog output.
control function assigned to it, TCON will operation). Return to a service center for - Check installation and operation of the
revert to transmission limphome mode. troubleshooting as soon as posible. connected actuator.
The assigned function can be blocked in the In all other cases disabling the assigned function Dynamic checking by the TCON of the digital - refer to the other reported errors to get more
Lamp Status Depending On Low Side Output 2: Voltage Above Normal, or Shorted To activated or deactivated state, possibly control will result in reduced vehicle operation. output detected the output is shorted to information about the configured output
56.03 520237 3 Corresponding Functional Error High Source resulting in reduced vehicle operation. Contact maintenance for troubleshooting. battery plus (high source). function.
TCON ERROR CODES & DESCRIPTIONS
Revision 2.54 - Firmware Version 2.04
Date: 3/3/2021
ERROR CODE
DANA [HEX] SAE J1939 DM 1 STATUS LAMP ERROR DESCRIPTION TCON ACTION DRIVER ACTION FAILURE CAUSE TROUBLESHOOTING
SPN FMI
In transmission limphome mode, the driver can - Check the wiring between the TCON and the
If the output has a critical transmission still operate the vehicle (reduced vehicle device connected to this analog output.
control function assigned to it, TCON will operation). Return to a service center for - Check installation and operation of the
revert to transmission limphome mode. troubleshooting as soon as posible. Dynamic checking by the TCON of the digital connected actuator.
The assigned function can be blocked in the In all other cases disabling the assigned function output detected the output is shorted to - refer to the other reported errors to get more
Lamp Status Depending On Low Side Output 2: Voltage Below Normal, or Shorted To activated or deactivated state, possibly control will result in reduced vehicle operation. ground (low source), or the actuator wires information about the configured output
56.04 520237 4 Corresponding Functional Error Low Source resulting in reduced vehicle operation. Contact maintenance for troubleshooting. are shorted to each other. function.
In transmission limphome mode, the driver can - Check the wiring between the TCON and the
If the output has a critical transmission still operate the vehicle (reduced vehicle device connected to this analog output.
control function assigned to it, TCON will operation). Return to a service center for - Check installation and operation of the
revert to transmission limphome mode. troubleshooting as soon as posible. connected actuator.
The assigned function can be blocked in the In all other cases disabling the assigned function Dynamic checking by the TCON of the - refer to the other reported errors to get more
Lamp Status Depending On Low Side Output 2: Current Below Normal, or Open activated or deactivated state, possibly control will result in reduced vehicle operation. analog output detected the output is in information about the configured output
56.05 520237 5 Corresponding Functional Error Circuit resulting in reduced vehicle operation. Contact maintenance for troubleshooting. open circuit (loose connection). function.
In transmission limphome mode, the driver can - Check the wiring between the TCON and the
If the output has a critical transmission still operate the vehicle (reduced vehicle device connected to this analog output.
control function assigned to it, TCON will operation). Return to a service center for - Check installation and operation of the
revert to transmission limphome mode. troubleshooting as soon as posible. connected actuator.
The assigned function can be blocked in the In all other cases disabling the assigned function Dynamic checking by the TCON of the digital - refer to the other reported errors to get more
Lamp Status Depending On Low Side Output 3: Voltage Above Normal, or Shorted To activated or deactivated state, possibly control will result in reduced vehicle operation. output detected the output is shorted to information about the configured output
57.03 520238 3 Corresponding Functional Error High Source resulting in reduced vehicle operation. Contact maintenance for troubleshooting. battery plus (high source). function.
In transmission limphome mode, the driver can - Check the wiring between the TCON and the
If the output has a critical transmission still operate the vehicle (reduced vehicle device connected to this analog output.
control function assigned to it, TCON will operation). Return to a service center for - Check installation and operation of the
revert to transmission limphome mode. troubleshooting as soon as posible. Dynamic checking by the TCON of the digital connected actuator.
The assigned function can be blocked in the In all other cases disabling the assigned function output detected the output is shorted to - refer to the other reported errors to get more
Lamp Status Depending On Low Side Output 3: Voltage Below Normal, or Shorted To activated or deactivated state, possibly control will result in reduced vehicle operation. ground (low source), or the actuator wires information about the configured output
57.04 520238 4 Corresponding Functional Error Low Source resulting in reduced vehicle operation. Contact maintenance for troubleshooting. are shorted to each other. function.
In transmission limphome mode, the driver can - Check the wiring between the TCON and the
If the output has a critical transmission still operate the vehicle (reduced vehicle device connected to this analog output.
control function assigned to it, TCON will operation). Return to a service center for - Check installation and operation of the
revert to transmission limphome mode. troubleshooting as soon as posible. connected actuator.
The assigned function can be blocked in the In all other cases disabling the assigned function Dynamic checking by the TCON of the - refer to the other reported errors to get more
Lamp Status Depending On Low Side Output 3: Current Below Normal, or Open activated or deactivated state, possibly control will result in reduced vehicle operation. analog output detected the output is in information about the configured output
57.05 520238 5 Corresponding Functional Error Circuit resulting in reduced vehicle operation. Contact maintenance for troubleshooting. open circuit (loose connection). function.
ERROR CODE
DANA [HEX] SAE J1939 DM 1 STATUS LAMP ERROR DESCRIPTION TCON ACTION DRIVER ACTION FAILURE CAUSE TROUBLESHOOTING
SPN FMI
ERROR CODE
DANA [HEX] SAE J1939 DM 1 STATUS LAMP ERROR DESCRIPTION TCON ACTION DRIVER ACTION FAILURE CAUSE TROUBLESHOOTING
SPN FMI
ERROR CODE
DANA [HEX] SAE J1939 DM 1 STATUS LAMP ERROR DESCRIPTION TCON ACTION DRIVER ACTION FAILURE CAUSE TROUBLESHOOTING
SPN FMI
ERROR CODE
DANA [HEX] SAE J1939 DM 1 STATUS LAMP ERROR DESCRIPTION TCON ACTION DRIVER ACTION FAILURE CAUSE TROUBLESHOOTING
SPN FMI
ERROR CODE
DANA [HEX] SAE J1939 DM 1 STATUS LAMP ERROR DESCRIPTION TCON ACTION DRIVER ACTION FAILURE CAUSE TROUBLESHOOTING
SPN FMI
ERROR CODE
DANA [HEX] SAE J1939 DM 1 STATUS LAMP ERROR DESCRIPTION TCON ACTION DRIVER ACTION FAILURE CAUSE TROUBLESHOOTING
SPN FMI
ERROR CODE
DANA [HEX] SAE J1939 DM 1 STATUS LAMP ERROR DESCRIPTION TCON ACTION DRIVER ACTION FAILURE CAUSE TROUBLESHOOTING
SPN FMI
ERROR CODE
DANA [HEX] SAE J1939 DM 1 STATUS LAMP ERROR DESCRIPTION TCON ACTION DRIVER ACTION FAILURE CAUSE TROUBLESHOOTING
SPN FMI
ERROR CODE
DANA [HEX] SAE J1939 DM 1 STATUS LAMP ERROR DESCRIPTION TCON ACTION DRIVER ACTION FAILURE CAUSE TROUBLESHOOTING
SPN FMI
- Check if digital output has its expected value
and if the mechanical actuator has made the
switch.
Output Function: 4WD/2WD: Data Valid but Above Contact maintenance for troubleshooting The mechanical actuator is stuck engaged or - Check if the digital feedback is switched and
A2.00 520254 0 Amber warning Flashing Normal Operational Range - Most Severe TCON will try to actuate the output. the feedback line is faulty. still connected to the controller.
- Check if digital output has its expected value
and if the mechanical actuator has made the
switch.
Output Function: 4WD/2WD: Data Valid but Below Contact maintenance for troubleshooting The mechanical actuator is stuck - Check if the digital feedback is switched and
A2.01 520254 1 Amber warning Flashing Normal Operational Range - Most Severe TCON will try to actuate the output. disengaged or the feedback line is faulty. still connected to the controller.
ERROR CODE
DANA [HEX] SAE J1939 DM 1 STATUS LAMP ERROR DESCRIPTION TCON ACTION DRIVER ACTION FAILURE CAUSE TROUBLESHOOTING
SPN FMI
ERROR CODE
DANA [HEX] SAE J1939 DM 1 STATUS LAMP ERROR DESCRIPTION TCON ACTION DRIVER ACTION FAILURE CAUSE TROUBLESHOOTING
SPN FMI
TCON will continue normal operation, but CAN message containing value for the Check if the CAN message containing the output
this output function will not be broadcasted Contact maintenance for troubleshooting output function cannot be broadcasted or function is configured.
A5.09 520257 9 Amber warning Flashing Output Function: Parking brake: Abnormal Update Rate over CAN. constructed.
ERROR CODE
DANA [HEX] SAE J1939 DM 1 STATUS LAMP ERROR DESCRIPTION TCON ACTION DRIVER ACTION FAILURE CAUSE TROUBLESHOOTING
SPN FMI
ERROR CODE
DANA [HEX] SAE J1939 DM 1 STATUS LAMP ERROR DESCRIPTION TCON ACTION DRIVER ACTION FAILURE CAUSE TROUBLESHOOTING
SPN FMI
ERROR CODE
DANA [HEX] SAE J1939 DM 1 STATUS LAMP ERROR DESCRIPTION TCON ACTION DRIVER ACTION FAILURE CAUSE TROUBLESHOOTING
SPN FMI
ERROR CODE
DANA [HEX] SAE J1939 DM 1 STATUS LAMP ERROR DESCRIPTION TCON ACTION DRIVER ACTION FAILURE CAUSE TROUBLESHOOTING
SPN FMI
ERROR CODE
DANA [HEX] SAE J1939 DM 1 STATUS LAMP ERROR DESCRIPTION TCON ACTION DRIVER ACTION FAILURE CAUSE TROUBLESHOOTING
SPN FMI
ERROR CODE
DANA [HEX] SAE J1939 DM 1 STATUS LAMP ERROR DESCRIPTION TCON ACTION DRIVER ACTION FAILURE CAUSE TROUBLESHOOTING
SPN FMI
ERROR CODE
DANA [HEX] SAE J1939 DM 1 STATUS LAMP ERROR DESCRIPTION TCON ACTION DRIVER ACTION FAILURE CAUSE TROUBLESHOOTING
SPN FMI
Engine speed / torque exceeds allowed max speed / TCON will continue normal operation. If the Engine speed or torque is above - Check if engine control is following engine
torque: Data Valid but Above Normal Operational Range - overtorque or overspeed condition persists, commanded engine speed or torque limit command provided by TCON
BA.0F 520278 15 Protection Lamp Least Severe. TCON will escalate this warning into FMI 0. Reduce engine speed or power. for limited duration. - check CAN communication
TCON will revert to shutdown mode. This
will result in inoperability of the vehicle.
TCON will only resume normal operation
direction selection: shift lever: Data Erratic, Intermittent, once the error is cleared and TCON is Contact maintenance for troubleshooting The expected value for the direction Check the wiring between the TCON and the
28.02 520286 2 Stop Lamp Flashing or Incorrect restarted. selection contains an invalid pattern. shiftlever concerning the direction signals.
TCON will revert to shutdown mode. This
will result in inoperability of the vehicle. CAN message containing value for the - Check if CAN message containing the shiftlever
TCON will only resume normal operation shiftelver function not received within the function value is sent correctly on the CAN bus.
once the error is cleared and TCON is Contact maintenance for troubleshooting expected timeframe or not present on the - Check if the repetition rate of the CAN
28.09 520286 9 Stop Lamp Flashing direction selection: shift lever: Abnormal Update Rate restarted. CAN bus. message is fast enough.
TCON ERROR CODES & DESCRIPTIONS
Revision 2.54 - Firmware Version 2.04
Date: 3/3/2021
ERROR CODE
DANA [HEX] SAE J1939 DM 1 STATUS LAMP ERROR DESCRIPTION TCON ACTION DRIVER ACTION FAILURE CAUSE TROUBLESHOOTING
SPN FMI
TCON will revert to shutdown mode. This
will result in inoperability of the vehicle. The expected value for the shiftlever
TCON will only resume normal operation function received by the corresponding CAN Check the source signal from the CAN message
direction selection: shift lever: Received Network Data in once the error is cleared and TCON is Contact maintenance for troubleshooting message contains an invalid or unavailable containing the shiftlever function for requesting
28.13 520286 19 Stop Lamp Flashing Error restarted. value. a valid value.
TCON will continue normal operation, but
the value of the gear shift lever will be
replaced by the closest corresponding
value.
gear selection: shift lever: Data Erratic, Intermittent, or This may result in reduced operation of the Contact maintenance for troubleshooting The expected value for the gear selection Check the wiring between the TCON and the
29.02 520287 2 Amber warning Flashing Incorrect vehicle. contains an invalid pattern. shiftlever concerning the gear signals.
TCON will continue normal operation, but
the value of the gear shift lever will be
replaced by the closest corresponding CAN message containing value for the - Check if CAN message containing the shiftlever
value. shiftelver function not received within the function value is sent correctly on the CAN bus.
This may result in reduced operation of the Contact maintenance for troubleshooting expected timeframe or not present on the - Check if the repetition rate of the CAN
29.09 520287 9 Amber warning Flashing gear selection: shift lever: Abnormal Update Rate vehicle. CAN bus. message is fast enough.
TCON will continue normal operation, but
the value of the gear shift lever will be
replaced by the closest corresponding The expected value for the shiftlever
value. function received by the corresponding CAN Check the source signal from the CAN message
gear selection: shift lever: Received Network Data in This may result in reduced operation of the Contact maintenance for troubleshooting message contains an invalid or unavailable containing the shiftlever function for requesting
29.13 520287 19 Amber warning Flashing Error vehicle. value. a valid value.
The TCON will flag the fault and the state of The expected value for the input function, Check the source signal from the CAN message
the function will be replaced by an received by the corresponding CAN containing the input function for requesting a
Digital Input Function: Shift lever Selection Abnormal appropriate default value. This may result in message contains an invalid or unavailable valid value.
2D.09 520288 9 Amber warning Flashing Update Rate reduced vehicle operation. Contact maintenance for troubleshooting value. Check the can bus communication.
In transmission shutdown mode, the driver can - Check the wiring between the TCON and the
If the output has a critical transmission no longer operate the vehicle. Return to a device connected to this analog output.
control function assigned to it, TCON will service center for troubleshooting as soon as - Check installation and operation of the
revert to transmission shutdown mode. posible. connected actuator.
In all other cases the assigned function In all other cases disabling the assigned function Dynamic checking by the TCON of the - refer to the other reported errors to get more
Lamp Status Depending On Analog Output 6: Voltage Above Normal, or Shorted To control will be disabled, possibly resulting in control will result in reduced vehicle operation. analog output detected that the output is information about the configured output
4D.03 520294 3 Corresponding Functional Error High Source reduced vehicle operation. Contact maintenance for troubleshooting. shorted to battery plus (high source). function.
In transmission limphome mode, the driver can - Check the wiring between the TCON and the
If the output has a critical transmission still operate the vehicle (reduced vehicle device connected to this analog output.
control function assigned to it, TCON will operation). Return to a service center for - Check installation and operation of the
revert to transmission limphome mode. troubleshooting as soon as posible. connected actuator.
In any case the assigned function control In all other cases disabling the assigned function Dynamic checking by the TCON of the - refer to the other reported errors to get more
Lamp Status Depending On Analog Output 6: Voltage Below Normal, or Shorted To will be disabled, possibly resulting in control will result in reduced vehicle operation. output detected that the output is shorted information about the configured output
4D.04 520294 4 Corresponding Functional Error Low Source reduced vehicle operation. Contact maintenance for troubleshooting. to ground (low source). function.
In transmission limphome mode, the driver can - Check the wiring between the TCON and the
If the output has a critical transmission still operate the vehicle (reduced vehicle device connected to this analog output.
control function assigned to it, TCON will operation). Return to a service center for - Check installation and operation of the
revert to transmission limphome mode. troubleshooting as soon as posible. connected actuator.
In any case the assigned function control In all other cases disabling the assigned function Dynamic checking by the TCON of the - refer to the other reported errors to get more
Lamp Status Depending On will be disabled, possibly resulting in control will result in reduced vehicle operation. analog output detected the output is in information about the configured output
4D.05 520294 5 Corresponding Functional Error Analog Output 6: Current Below Normal, or Open Circuit reduced vehicle operation. Contact maintenance for troubleshooting. open circuit (loose connection). function.
TCON ERROR CODES & DESCRIPTIONS
Revision 2.54 - Firmware Version 2.04
Date: 3/3/2021
ERROR CODE
DANA [HEX] SAE J1939 DM 1 STATUS LAMP ERROR DESCRIPTION TCON ACTION DRIVER ACTION FAILURE CAUSE TROUBLESHOOTING
SPN FMI
In transmission shutdown mode, the driver can - Check the wiring between the TCON and the
If the output has a critical transmission no longer operate the vehicle. Return to a device connected to this analog output.
control function assigned to it, TCON will service center for troubleshooting as soon as - Check installation and operation of the
revert to transmission shutdown mode. posible. connected actuator.
In all other cases the assigned function In all other cases disabling the assigned function - refer to the other reported errors to get more
Lamp Status Depending On Analog Output 6: Current Above Normal or Grounded control will be disabled, possibly resulting in control will result in reduced vehicle operation. Dynamic checking by the TCON ofthe analog information about the configured output
4D.06 520294 6 Corresponding Functional Error Circuit reduced vehicle operation. Contact maintenance for troubleshooting. output detected an overcurrent. function.
In transmission limphome mode, the driver can - Check the wiring between the TCON and the
If the output has a critical transmission still operate the vehicle (reduced vehicle device connected to this analog output.
control function assigned to it, TCON will operation). Return to a service center for - Check installation and operation of the
revert to transmission limphome mode. troubleshooting as soon as posible. connected actuator.
In any case the assigned function control In all other cases disabling the assigned function The TCON detected that the output current - refer to the other reported errors to get more
Lamp Status Depending On Analog Output 6: Abnormal Frequency or Pulse Width or will be disabled, possibly resulting in control will result in reduced vehicle operation. is out of range. This occurs when the load information about the configured output
4D.08 520294 8 Corresponding Functional Error Period reduced vehicle operation. Contact maintenance for troubleshooting. has an incorrect impedance. function.
In transmission shutdown mode, the driver can - Check the wiring between the TCON and the
If the output has a critical transmission no longer operate the vehicle. Return to a device connected to this analog output.
control function assigned to it, TCON will service center for troubleshooting as soon as - Check installation and operation of the
revert to transmission shutdown mode. posible. connected actuator.
In all other cases the assigned function In all other cases disabling the assigned function Dynamic checking by the TCON of the - refer to the other reported errors to get more
Lamp Status Depending On Analog Output 7: Voltage Above Normal, or Shorted To control will be disabled, possibly resulting in control will result in reduced vehicle operation. analog output detected that the output is information about the configured output
4E.03 520295 3 Corresponding Functional Error High Source reduced vehicle operation. Contact maintenance for troubleshooting. shorted to battery plus (high source). function.
In transmission limphome mode, the driver can - Check the wiring between the TCON and the
If the output has a critical transmission still operate the vehicle (reduced vehicle device connected to this analog output.
control function assigned to it, TCON will operation). Return to a service center for - Check installation and operation of the
revert to transmission limphome mode. troubleshooting as soon as posible. connected actuator.
In any case the assigned function control In all other cases disabling the assigned function Dynamic checking by the TCON of the - refer to the other reported errors to get more
Lamp Status Depending On Analog Output 7: Voltage Below Normal, or Shorted To will be disabled, possibly resulting in control will result in reduced vehicle operation. output detected that the output is shorted information about the configured output
4E.04 520295 4 Corresponding Functional Error Low Source reduced vehicle operation. Contact maintenance for troubleshooting. to ground (low source). function.
In transmission limphome mode, the driver can - Check the wiring between the TCON and the
If the output has a critical transmission still operate the vehicle (reduced vehicle device connected to this analog output.
control function assigned to it, TCON will operation). Return to a service center for - Check installation and operation of the
revert to transmission limphome mode. troubleshooting as soon as posible. connected actuator.
In any case the assigned function control In all other cases disabling the assigned function Dynamic checking by the TCON of the - refer to the other reported errors to get more
Lamp Status Depending On will be disabled, possibly resulting in control will result in reduced vehicle operation. analog output detected the output is in information about the configured output
4E.05 520295 5 Corresponding Functional Error Analog Output 7: Current Below Normal, or Open Circuit reduced vehicle operation. Contact maintenance for troubleshooting. open circuit (loose connection). function.
In transmission shutdown mode, the driver can - Check the wiring between the TCON and the
If the output has a critical transmission no longer operate the vehicle. Return to a device connected to this analog output.
control function assigned to it, TCON will service center for troubleshooting as soon as - Check installation and operation of the
revert to transmission shutdown mode. posible. connected actuator.
In all other cases the assigned function In all other cases disabling the assigned function - refer to the other reported errors to get more
Lamp Status Depending On Analog Output 7: Current Above Normal or Grounded control will be disabled, possibly resulting in control will result in reduced vehicle operation. Dynamic checking by the TCON ofthe analog information about the configured output
4E.06 520295 6 Corresponding Functional Error Circuit reduced vehicle operation. Contact maintenance for troubleshooting. output detected an overcurrent. function.
TCON ERROR CODES & DESCRIPTIONS
Revision 2.54 - Firmware Version 2.04
Date: 3/3/2021
ERROR CODE
DANA [HEX] SAE J1939 DM 1 STATUS LAMP ERROR DESCRIPTION TCON ACTION DRIVER ACTION FAILURE CAUSE TROUBLESHOOTING
SPN FMI
In transmission limphome mode, the driver can - Check the wiring between the TCON and the
If the output has a critical transmission still operate the vehicle (reduced vehicle device connected to this analog output.
control function assigned to it, TCON will operation). Return to a service center for - Check installation and operation of the
revert to transmission limphome mode. troubleshooting as soon as posible. connected actuator.
In any case the assigned function control In all other cases disabling the assigned function The TCON detected that the output current - refer to the other reported errors to get more
Lamp Status Depending On Analog Output 7: Abnormal Frequency or Pulse Width or will be disabled, possibly resulting in control will result in reduced vehicle operation. is out of range. This occurs when the load information about the configured output
4E.08 520295 8 Corresponding Functional Error Period reduced vehicle operation. Contact maintenance for troubleshooting. has an incorrect impedance. function.
ERROR CODE
DANA [HEX] SAE J1939 DM 1 STATUS LAMP ERROR DESCRIPTION TCON ACTION DRIVER ACTION FAILURE CAUSE TROUBLESHOOTING
SPN FMI
ERROR CODE
DANA [HEX] SAE J1939 DM 1 STATUS LAMP ERROR DESCRIPTION TCON ACTION DRIVER ACTION FAILURE CAUSE TROUBLESHOOTING
SPN FMI
ERROR CODE
DANA [HEX] SAE J1939 DM 1 STATUS LAMP ERROR DESCRIPTION TCON ACTION DRIVER ACTION FAILURE CAUSE TROUBLESHOOTING
SPN FMI
ERROR CODE
DANA [HEX] SAE J1939 DM 1 STATUS LAMP ERROR DESCRIPTION TCON ACTION DRIVER ACTION FAILURE CAUSE TROUBLESHOOTING
SPN FMI
TCON will revert to shutdown mode. This
will result in inoperability of the vehicle. The expected value for the input function, Check the source signal from the CAN message
TCON will only resume normal operation received by the corresponding CAN containing the input function for requesting a
Input Function: Forward Clutch Pressure: Abnormal once the error is cleared and TCON is Contact maintenance for troubleshooting message contains an invalid or unavailable valid value.
0A.09 520304 9 Stop Lamp Flashing Update Rate restarted. value. Check the can bus communication.
TCON will revert to shutdown mode. This
will result in inoperability of the vehicle. The expected value for the input function
TCON will only resume normal operation received by the corresponding CAN Check the source signal from the CAN message
Input Function: Forward Clutch Pressure: Received once the error is cleared and TCON is Contact maintenance for troubleshooting message contains an invalid or unavailable containing the input function for requesting a
0A.13 520304 19 Stop Lamp Flashing Network Data in Error restarted. value. valid value.
ERROR CODE
DANA [HEX] SAE J1939 DM 1 STATUS LAMP ERROR DESCRIPTION TCON ACTION DRIVER ACTION FAILURE CAUSE TROUBLESHOOTING
SPN FMI
ERROR CODE
DANA [HEX] SAE J1939 DM 1 STATUS LAMP ERROR DESCRIPTION TCON ACTION DRIVER ACTION FAILURE CAUSE TROUBLESHOOTING
SPN FMI
TCON will revert to shutdown mode. This
will result in inoperability of the vehicle. The expected value for the input function, Check the source signal from the CAN message
TCON will only resume normal operation received by the corresponding CAN containing the input function for requesting a
Input Function: 1st Clutch Pressure: Abnormal Update once the error is cleared and TCON is Contact maintenance for troubleshooting message contains an invalid or unavailable valid value.
0D.09 520307 9 Stop Lamp Flashing Rate restarted. value. Check the can bus communication.
TCON will revert to shutdown mode. This
will result in inoperability of the vehicle. The expected value for the input function
TCON will only resume normal operation received by the corresponding CAN Check the source signal from the CAN message
Input Function: 1st Clutch Pressure: Received Network once the error is cleared and TCON is Contact maintenance for troubleshooting message contains an invalid or unavailable containing the input function for requesting a
0D.13 520307 19 Stop Lamp Flashing Data in Error restarted. value. valid value.
ERROR CODE
DANA [HEX] SAE J1939 DM 1 STATUS LAMP ERROR DESCRIPTION TCON ACTION DRIVER ACTION FAILURE CAUSE TROUBLESHOOTING
SPN FMI
ERROR CODE
DANA [HEX] SAE J1939 DM 1 STATUS LAMP ERROR DESCRIPTION TCON ACTION DRIVER ACTION FAILURE CAUSE TROUBLESHOOTING
SPN FMI
TCON will revert to shutdown mode. This
will result in inoperability of the vehicle. The expected value for the input function, Check the source signal from the CAN message
TCON will only resume normal operation received by the corresponding CAN containing the input function for requesting a
Input Function: 4th Clutch Pressure: Abnormal Update once the error is cleared and TCON is Contact maintenance for troubleshooting message contains an invalid or unavailable valid value.
10.09 520310 9 Stop Lamp Flashing Rate restarted. value. Check the can bus communication.
TCON will revert to shutdown mode. This
will result in inoperability of the vehicle. The expected value for the input function
TCON will only resume normal operation received by the corresponding CAN Check the source signal from the CAN message
Input Function: 4th Clutch Pressure: Received Network once the error is cleared and TCON is Contact maintenance for troubleshooting message contains an invalid or unavailable containing the input function for requesting a
10.13 520310 19 Stop Lamp Flashing Data in Error restarted. value. valid value.
Measured pressure on this sensor is too - Check clutch pressure at engine idle when
TCON will continue normal operation but high in comparison with the commanded clutch is NOT selected (+-0 bar required).
lockup will be unavailable. TCON will only pressure by TCON: - Check clutch pressure when clutch is selected.
Lockup Pressure: Data Valid but Above Normal try to reactivate lockup when TCON is Contact maintenance for troubleshooting - Proportional solenoid stuck. Log pressure (CAN trace or other measurement
45.00 520312 0 Amber warning Flashing Operational Range - Most Severe restarted. - Clutch failure equipment) when problem occurs.
ERROR CODE
DANA [HEX] SAE J1939 DM 1 STATUS LAMP ERROR DESCRIPTION TCON ACTION DRIVER ACTION FAILURE CAUSE TROUBLESHOOTING
SPN FMI
The expected value for the input function, Check the source signal from the CAN message
received by the corresponding CAN containing the input function for requesting a
TCON will continue normal operation but Contact maintenance for troubleshooting message contains an invalid or unavailable valid value.
45.09 520312 9 Amber warning Flashing Lockup Pressure: Abnormal Update Rate lockup will be unavailable. value. Check the can bus communication.
ERROR CODE
DANA [HEX] SAE J1939 DM 1 STATUS LAMP ERROR DESCRIPTION TCON ACTION DRIVER ACTION FAILURE CAUSE TROUBLESHOOTING
SPN FMI
The value of the engine speed sensor, will
be replaced by an appropriate calculated - Check the transmission and speed sensors.
value. - Check the speed sensor position.
Speed Sensor Input Function: Engine speed: Data Valid The TCON will revert to transmission Turbine speed was detected but no engine - Check the can signal containing engine speed
41.01 520316 1 Stop Lamp Solid but Below Normal Operational Range - Most Severe limphome mode. Contact maintenance for troubleshooting speed was measured. (if configured via can)
The value of the engine speed sensor, will
be replaced by an appropriate calculated The measured current in the speed sensor - Check the transmission and speed sensors.
value. circuit is below normal. The input most - Check the speed sensor position.
Speed Sensor Input Function: Engine speed: Current The TCON will revert to transmission likely has a loose connection or it is shorted - Check the can signal containing engine speed
41.05 520316 5 Stop Lamp Solid Below Normal, or Open Circuit limphome mode. Contact maintenance for troubleshooting to battery plus (high source). (if configured via can)
The value of the engine speed sensor, will - Check if CAN message containing the engine
be replaced by an appropriate calculated speed value is sent correctly on the CAN bus.
value. No engine speed information available, as - Check if the repetition rate of that CAN
Speed Sensor Input Function: Engine speed: Abnormal The TCON will revert to transmission the EEC1 or CVC2TC message is missing on message is fast enough.
41.09 520316 9 Stop Lamp Solid Update Rate limphome mode. Contact maintenance for troubleshooting the CAN bus. - Check CAN connection to the controller.
The value of the engine speed sensor, will
be replaced by an appropriate calculated
value. The contents of the engine speed field in
Speed Sensor Input Function: Engine speed: Received The TCON will revert to transmission the EEC1 or CVC2TC message is set to error - Check engine controller.
41.13 520316 19 Stop Lamp Solid Network Data in Error limphome mode. Contact maintenance for troubleshooting or not available. - Check CAN connection to the controller.
Speed Sensor Input Function: Turbine speed: Data Contact maintenance for troubleshooting Direction reporting error of the speed - Check the speed sensor
42.02 520317 2 Stop Lamp Solid Erratic, Intermittent, or Incorrect TCON will revert to limphome mode. sensor. - Check the wiring of the speed sensor
- Check the wiring between the TCON and the
turbine speed sensor.
The value of the turbine speed sensor, will The measured current in the speed sensor - Check installation and operation of the speed
be replaced by an appropriate calculated circuit is below normal. The input most sensor connected.
Speed Sensor Input Function: Turbine speed: Current value. Contact maintenance for troubleshooting likely has a loose connection or it is shorted - refer to the other reported errors to identify
42.05 520317 5 Amber Warning Solid Below Normal, or Open Circuit The TCON will disable inching to battery plus (high source). the affected speed input.
- Check the wiring between the TCON and the
turbine speed sensor.
The value of the turbine speed sensor, will - Check installation and operation of the speed
be replaced by an appropriate calculated The measured current in the speed sensor sensor connected.
Speed Sensor Input Function: Turbine speed: Current value. Contact maintenance for troubleshooting circuit is above normal. The input is most - refer to the other reported errors to identify
42.06 520317 6 Amber Warning Solid Above Normal or Grounded Circuit The TCON will disable inching likely shorted to ground (low source). the affected speed input.
The intermediate rpm is 100 rpm above
what it should be. This can be determined
using output and turbine speed combined
Speed Sensor Input Function: intermediate speed: Data This message is given as additional with the gear ratios. To be able to check this Check the transmission, in order to understand
Valid but Above Normal Operational Range - Most information for transmission ratio faults. Contact maintenance for troubleshooting the turbine needs to be connected to the if and which clutch is slipping. Check the
43.00 520318 0 Amber Warning Solid Severe The action is taken by ratio fault monitoring. output. transmission ratio settings of the controller.
TCON ERROR CODES & DESCRIPTIONS
Revision 2.54 - Firmware Version 2.04
Date: 3/3/2021
ERROR CODE
DANA [HEX] SAE J1939 DM 1 STATUS LAMP ERROR DESCRIPTION TCON ACTION DRIVER ACTION FAILURE CAUSE TROUBLESHOOTING
SPN FMI
The intermediate rpm is 100 rpm below
what it should be. This can be determined
using output and turbine speed combined
This message is given as additional with the gear ratios. To be able to check this Check the transmission, in order to understand
Speed Sensor Input Function: intermediate speed: Data information for transmission ratio faults. Contact maintenance for troubleshooting the turbine needs to be connected to the if and which clutch is slipping. Check the
43.01 520318 1 Amber Warning Solid Valid but Below Normal Operational Range - Most Severe The action is taken by ratio fault monitoring. output. transmission ratio settings of the controller.
- Check the wiring between the TCON and the
turbine speed sensor.
The measured current in the speed sensor - Check installation and operation of the speed
The value of the intermediate speed sensor, circuit is below normal. The input most sensor connected.
Speed Sensor Input Function: intermediate speed: will be replaced by an appropriate Contact maintenance for troubleshooting likely has a loose connection or it is shorted - refer to the other reported errors to identify
43.05 520318 5 Amber Warning Solid Current Below Normal, or Open Circuit calculated value. to battery plus (high source). the affected speed input.
- Check the wiring between the TCON and the
intermediate speed sensor.
- Check installation and operation of the speed
The value of the intermediate speed sensor, The measured current in the speed sensor sensor connected.
Speed Sensor Input Function: intermediate speed: will be replaced by an appropriate circuit is above normal. The input is most - refer to the other reported errors to identify
43.06 520318 6 Amber Warning Solid Current Above Normal or Grounded Circuit calculated value. Contact maintenance for troubleshooting likely shorted to ground (low source). the affected speed input.
The output rpm is 100 rpm above what it
should be. This can be determined using
drum and turbine speed combined with the
This message is given as additional gear ratios. To be able to check this the Check the transmission, in order to understand
Speed Sensor Input Function: Output speed: Data Valid information for transmission ratio faults. turbine needs to be connected to the if and which clutch is slipping. Check the
44.00 520319 0 Amber Warning Solid but Above Normal Operational Range - Most Severe The action is taken by ratio fault monitoring. Contact maintenance for troubleshooting output. transmission ratio settings of the controller.
The output rpm is 100 rpm below what it
should be. This can be determined using
drum and turbine speed combined with the
This message is given as additional gear ratios. To be able to check this the Check the transmission, in order to understand
Speed Sensor Input Function: Output speed: Data Valid information for transmission ratio faults. turbine needs to be connected to the if and which clutch is slipping. Check the
44.01 520319 1 Amber Warning Solid but Below Normal Operational Range - Most Severe The action is taken by ratio fault monitoring. Contact maintenance for troubleshooting output. transmission ratio settings of the controller.
- Check the wiring between the TCON and the
output speed sensor.
The value of the output speed sensor, will The measured current in the speed sensor - Check installation and operation of the speed
be replaced by an appropriate calculated circuit is below normal. The input most sensor connected.
Speed Sensor Input Function: Output speed: Current value. likely has a loose connection or it is shorted - refer to the other reported errors to identify
44.05 520319 5 Amber Warning Solid Below Normal, or Open Circuit The TCON will disable inching Contact maintenance for troubleshooting to battery plus (high source). the affected speed input.
- Check the wiring between the TCON and the
output speed sensor.
The value of the output speed sensor, will - Check installation and operation of the speed
be replaced by an appropriate calculated The measured current in the speed sensor sensor connected.
Speed Sensor Input Function: Output speed: Current value. circuit is above normal. The input is most - refer to the other reported errors to identify
44.06 520319 6 Amber Warning Solid Above Normal or Grounded Circuit The TCON will disable inching Contact maintenance for troubleshooting likely shorted to ground (low source). the affected speed input.
ERROR CODE
DANA [HEX] SAE J1939 DM 1 STATUS LAMP ERROR DESCRIPTION TCON ACTION DRIVER ACTION FAILURE CAUSE TROUBLESHOOTING
SPN FMI
ERROR CODE
DANA [HEX] SAE J1939 DM 1 STATUS LAMP ERROR DESCRIPTION TCON ACTION DRIVER ACTION FAILURE CAUSE TROUBLESHOOTING
SPN FMI
- Recalibrate the input, if the problem persists,
check the wiring between the TCON and the
throttle pedal.
- Check installation and operation of the throttle
TCON will continue normal operation but pedal.
Analog Input Function: Throttle Pedal: Data Valid but the value for the throttle pedal will be Contact maintenance for troubleshooting or The measured value of the analog input is - refer to the other reported errors to identify
2C.00 520321 0 Amber Warning Solid Above Normal Operational Range - Most Severe clipped to the hightest value allowed. Perform a calibration of the connected device. above the maximum allowed range. the affected analogue input.
- Recalibrate the input, if the problem persists,
check the wiring between the TCON and the
throttle pedal.
- Check installation and operation of the throttle
TCON will continue normal operation but pedal.
Analog Input Function: Throttle Pedal: Data Valid but the value for the throttle pedal will be Contact maintenance for troubleshooting or The measured value of the analog input is - refer to the other reported errors to identify
2C.01 520321 1 Amber Warning Solid Below Normal Operational Range - Most Severe clipped to the lowest value allowed. Perform a calibration of the connected device. below the minimum allowed range. the affected analogue input.
- Recalibrate the input, if the problem persists,
check the wiring between the TCON and the
The value of the throttle pedal will be throttle pedal.
replaced by an appropriate default value. - Check installation and operation of the throttle
This will result in reduced vehicle operation, pedal.
Analog Input Function: Throttle Pedal: Voltage Above possibly no shifting or inching will be The input most likely has a loose connection - refer to the other reported errors to identify
2C.03 520321 3 Amber warning Flashing Normal, or Shorted To High Source allowed. Contact maintenance for troubleshooting or is shorted to battery plus. the affected analogue input.
- Recalibrate the input, if the problem persists,
check the wiring between the TCON and the
The value of the throttle pedal will be throttle pedal.
replaced by an appropriate default value. - Check installation and operation of the throttle
This will result in reduced vehicle operation, pedal.
Analog Input Function: Throttle Pedal: Voltage Below possibly no shifting or inching will be - refer to the other reported errors to identify
2C.04 520321 4 Amber warning Flashing Normal, or Shorted To Low Source allowed. Contact maintenance for troubleshooting The input is most likely shorted to ground. the affected analogue input.
ERROR CODE
DANA [HEX] SAE J1939 DM 1 STATUS LAMP ERROR DESCRIPTION TCON ACTION DRIVER ACTION FAILURE CAUSE TROUBLESHOOTING
SPN FMI
- Recalibrate the input, if the problem persists,
check the wiring between the TCON and the
throttle pedal.
- Check installation and operation of the throttle
TCON will continue normal operation but pedal.
Analog Input Function: Hydro Lever: Data Valid but the value for the hydro lever will be clipped Contact maintenance for troubleshooting or The measured value of the analog input is - refer to the other reported errors to identify
70.00 520322 0 Amber Warning Solid Above Normal Operational Range - Most Severe to the hightest value allowed. Perform a calibration of the connected device. above the maximum allowed range. the affected analogue input.
- Recalibrate the input, if the problem persists,
check the wiring between the TCON and the
hydro lever.
- Check installation and operation of the hydro
TCON will continue normal operation but lever.
Analog Input Function: Hydro Lever: Data Valid but the value for the hydro lever will be clipped Contact maintenance for troubleshooting or The measured value of the analog input is - refer to the other reported errors to identify
70.01 520322 1 Amber Warning Solid Below Normal Operational Range - Most Severe to the lowest value allowed. Perform a calibration of the connected device. below the minimum allowed range. the affected analogue input.
- Recalibrate the input, if the problem persists,
check the wiring between the TCON and the
The TCON will flag the fault and the value of hydro lever.
the hydro lever will be replaced by an - Check installation and operation of the hydro
appropriate default value. This will result in lever.
Analog Input Function: Hydro Lever: Voltage Above reduced vehicle operation, no engine The input most likely has a loose connection - refer to the other reported errors to identify
70.03 520322 3 Amber warning Flashing Normal, or Shorted To High Source control for hydro lever will be available. Contact maintenance for troubleshooting or is shorted to battery plus. the affected analogue input.
- Recalibrate the input, if the problem persists,
check the wiring between the TCON and the
The TCON will flag the fault and the value of hydro lever.
the hydro lever will be replaced by an - Check installation and operation of the hydro
appropriate default value. This will result in lever.
Analog Input Function: Hydro Lever: Voltage Below reduced vehicle operation, no engine - refer to the other reported errors to identify
70.04 520322 4 Amber warning Flashing Normal, or Shorted To Low Source control for hydro lever will be available. Contact maintenance for troubleshooting The input is most likely shorted to ground. the affected analogue input.
The TCON will flag the fault and the value of - Check if CAN message containing the hydro
the hydro lever will be replaced by an lever value is sent correctly on the CAN bus.
appropriate default value. This will result in No hydro lever information available, as the - Check if the repetition rate of that CAN
Analog Input Function: Hydro Lever: Abnormal Update reduced vehicle operation, no engine required CVC2TC message is missing on the message is fast enough.
70.09 520322 9 Amber warning Flashing Rate control for hydro lever will be available. Contact maintenance for troubleshooting CAN bus. - Check CAN connection to the controller.
ERROR CODE
DANA [HEX] SAE J1939 DM 1 STATUS LAMP ERROR DESCRIPTION TCON ACTION DRIVER ACTION FAILURE CAUSE TROUBLESHOOTING
SPN FMI
- Recalibrate the input, if the problem persists,
check the wiring between the TCON and the
throttle pedal.
- Check installation and operation of the throttle
TCON will continue normal operation but pedal.
Analog Input Function: Brake Pedal: Data Valid but Above the value for the brake pedal will be clipped Contact maintenance for troubleshooting or The measured value of the analog input is - refer to the other reported errors to identify
71.00 520323 0 Amber Warning Solid Normal Operational Range - Most Severe to the hightest value allowed. Perform a calibration of the connected device. above the maximum allowed range. the affected analogue input.
- Recalibrate the input, if the problem persists,
check the wiring between the TCON and the
brake pedal.
- Check installation and operation of the brake
TCON will continue normal operation but pedal.
Analog Input Function: Brake Pedal: Data Valid but Below the value for the brake pedal will be clipped Contact maintenance for troubleshooting or The measured value of the analog input is - refer to the other reported errors to identify
71.01 520323 1 Amber Warning Solid Normal Operational Range - Most Severe to the lowest value allowed. Perform a calibration of the connected device. below the minimum allowed range. the affected analogue input.
- Recalibrate the input, if the problem persists,
check the wiring between the TCON and the
brake pedal.
The value of the brake pedal will be - Check installation and operation of the brake
replaced by an appropriate default value. pedal.
Analog Input Function: Brake Pedal: Voltage Above This will result in reduced vehicle operation, The input most likely has a loose connection - refer to the other reported errors to identify
71.03 520323 3 Amber warning Flashing Normal, or Shorted To High Source possibly no inching will be allowed. Contact maintenance for troubleshooting or is shorted to battery plus. the affected analogue input.
- Recalibrate the input, if the problem persists,
check the wiring between the TCON and the
brake pedal.
The value of the brake pedal will be - Check installation and operation of the brake
replaced by an appropriate default value. pedal.
Analog Input Function: Brake Pedal: Voltage Below This will result in reduced vehicle operation, - refer to the other reported errors to identify
71.04 520323 4 Amber warning Flashing Normal, or Shorted To Low Source possibly no inching will be allowed. Contact maintenance for troubleshooting The input is most likely shorted to ground. the affected analogue input.
The TCON will flag the fault and the value of - Check if CAN message containing the brake
the brake pedal will be replaced by an pedal value is sent correctly on the CAN bus.
appropriate default value. This will result in No brake pedal information available, as the - Check if the repetition rate of that CAN
Analog Input Function: Brake Pedal: Abnormal Update reduced vehicle operation, possibly no required CVC2TC message is missing on the message is fast enough.
71.09 520323 9 Amber warning Flashing Rate inching will be allowed. Contact maintenance for troubleshooting CAN bus. - Check CAN connection to the controller.
ERROR CODE
DANA [HEX] SAE J1939 DM 1 STATUS LAMP ERROR DESCRIPTION TCON ACTION DRIVER ACTION FAILURE CAUSE TROUBLESHOOTING
SPN FMI
- Check the wiring between the TCON and the
sump temperature sensor.
- Check installation and operation of the sump
temperature sensor.
Analog Input Function: Transmission Sump Temperature: The TCON will flag the fault, and take the - refer to the other reported errors to identify
Data Valid but Above Normal Operational Range - Most configured action (either no action, force the configured analogue input.
72.00 520324 0 Amber warning Flashing Severe neutral or reduce engine revs) Contact maintenance for troubleshooting Transmission sump temperature too hot. - Check the operation of the cooler.
- Check the wiring between the TCON and the
sump temperature sensor.
- Check installation and operation of the sump
The TCON will flag the fault and will use a temperature sensor.
Analog Input Function: Transmission Sump Temperature: default value in its settings (which results in The input most likely has a loose connection - refer to the other reported errors to identify
72.03 520324 3 Amber warning Flashing Voltage Above Normal, or Shorted To High Source bad temperature compensation) Contact maintenance for troubleshooting or is shorted to battery plus. the configured analogue input.
- Check the wiring between the TCON and the
sump temperature sensor.
- Check installation and operation of the sump
The TCON will flag the fault and will use a temperature sensor.
Analog Input Function: Transmission Sump Temperature: default value in its settings (which results in - refer to the other reported errors to identify
72.04 520324 4 Amber warning Flashing Voltage Below Normal, or Shorted To Low Source bad temperature compensation) Contact maintenance for troubleshooting The input is most likely shorted to ground. the configured analogue input.
Analog Input function: Transmission Sump out The measured value of the sump
temperature : Data Valid but Above Normal Operational TCON will flag the fault in order to indicate Take notice of the fault, and try to bring the temperature is above the warning level Check the sump temperature and the converter
72.0F 520324 15 Protection Lamp Range - Least Severe the warning level to the driver. sump temperature to a lower level. temperature. out temperature sensor.
Stop the vehicle, select neutral and apply full
throttle (limited to 1500 rpm) in order to cool
The TCON is protecting the transmission the transmission oil until the fault disappears. Check the converter out temperature and the
Analog Input function: Transmission convertor out and does not allow that the converter out Once the converter out temperature is below The measured value of the convertor out converter out temperature sensor.
temperature : Data Valid but Above Normal Operational temperature exceeds its limit. The engine the critical temperature, resume normal temperature is above the critical If operating in dirty environment clean out
2B.00 520325 0 Amber warning Flashing Range - Most Severe will be limited to 1500 rpm. operation. temperature. radiator fins to allow maximum air flow.
TCON will disable inching. Other actions - check the wiring between the TCON and the
depends on parameter setting: filter indicator.
- either TCON will limit the engine speed to - Check installation and operation of the filter
a lower value until the filter clogging input indicator.
Input Function: Filter Clogging: Voltage Above Normal, or becomes inactive. The input most likely has a loose connection - refer to the other reported errors to identify
73.03 520326 3 Amber warning Flashing Shorted To High Source - either TCON will take no further action Contact maintenance for troubleshooting or is shorted to battery plus. the affected analogue input.
TCON ERROR CODES & DESCRIPTIONS
Revision 2.54 - Firmware Version 2.04
Date: 3/3/2021
ERROR CODE
DANA [HEX] SAE J1939 DM 1 STATUS LAMP ERROR DESCRIPTION TCON ACTION DRIVER ACTION FAILURE CAUSE TROUBLESHOOTING
SPN FMI
TCON will disable inching. Other actions - check the wiring between the TCON and the
depends on parameter setting: filter indicator.
- either TCON will limit the engine speed to - Check installation and operation of the filter
a lower value until the filter clogging input indicator.
Input Function: Filter Clogging: Voltage Below Normal, or becomes inactive. - refer to the other reported errors to identify
73.04 520326 4 Amber warning Flashing Shorted To Low Source - either TCON will take no further action Contact maintenance for troubleshooting The input is most likely shorted to ground. the affected analogue input.
ERROR CODE
DANA [HEX] SAE J1939 DM 1 STATUS LAMP ERROR DESCRIPTION TCON ACTION DRIVER ACTION FAILURE CAUSE TROUBLESHOOTING
SPN FMI
ERROR CODE
DANA [HEX] SAE J1939 DM 1 STATUS LAMP ERROR DESCRIPTION TCON ACTION DRIVER ACTION FAILURE CAUSE TROUBLESHOOTING
SPN FMI
TCON will revert to shutdown mode. This
will result in inoperability of the vehicle. The expected value for the input function, Check the source signal from the CAN message
TCON will only resume normal operation received by the corresponding CAN containing the input function for requesting a
Input Function: Clutch High Pressure: Abnormal Update once the error is cleared and TCON is Contact maintenance for troubleshooting message contains an invalid or unavailable valid value.
13.09 520329 9 Stop Lamp Flashing Rate restarted. value. Check the can bus communication.
TCON will revert to shutdown mode. This
will result in inoperability of the vehicle. The expected value for the input function
TCON will only resume normal operation received by the corresponding CAN Check the source signal from the CAN message
Input Function: Clutch High Pressure: Received Network once the error is cleared and TCON is Contact maintenance for troubleshooting message contains an invalid or unavailable containing the input function for requesting a
13.13 520329 19 Stop Lamp Flashing Data in Error restarted. value. valid value.
The TCON will flag the fault and the state of The expected value for the input function, Check the source signal from the CAN message
the function will be replaced by an received by the corresponding CAN containing the input function for requesting a
appropriate default value. This may result in message contains an invalid or unavailable valid value.
79.09 520330 9 Amber warning Flashing Digital Input Function: Declutch: Abnormal Update Rate reduced vehicle operation. Contact maintenance for troubleshooting value. Check the can bus communication.
The TCON will flag the fault and the state of The expected value for the input function, Check the source signal from the CAN message
the function will be replaced by an received by the corresponding CAN containing the input function for requesting a
Digital Input Function: Automatic Shifting: Abnormal appropriate default value. This may result in message contains an invalid or unavailable valid value.
7A.09 520331 9 Amber warning Flashing Update Rate reduced vehicle operation. Contact maintenance for troubleshooting value. Check the can bus communication.
TCON will continue normal operation, but
the value of the input function
Manual/Automatic shifting will be replaced The expected value for the input function Check the source signal from the CAN message
by the default value. Manual/Automatic shifting received by the containing the input function
Digital Input Function: Automatic Shifting: Received This will result in reduced operation of the Contact maintenance for troubleshooting corresponding CAN message contains an Manual/Automatic shifting for requesting a valid
7A.13 520331 19 Amber warning Flashing Network Data in Error vehicle. invalid or unavailable value. value.
The TCON will flag the fault and the state of The expected value for the input function, Check the source signal from the CAN message
the function will be replaced by an received by the corresponding CAN containing the input function for requesting a
Digital Input Function: Inching Enable: Abnormal Update appropriate default value. This may result in message contains an invalid or unavailable valid value.
7B.09 520332 9 Amber warning Flashing Rate reduced vehicle operation. Contact maintenance for troubleshooting value. Check the can bus communication.
The TCON will flag the fault and the state of The expected value for the input function, Check the source signal from the CAN message
the function will be replaced by an received by the corresponding CAN containing the input function for requesting a
Digital Input Function: Parking Brake: Abnormal Update appropriate default value. This may result in message contains an invalid or unavailable valid value.
7C.09 520333 9 Amber warning Flashing Rate reduced vehicle operation. Contact maintenance for troubleshooting value. Check the can bus communication.
The TCON will flag the fault and the state of The expected value for the input function, Check the source signal from the CAN message
the function will be replaced by an received by the corresponding CAN containing the input function for requesting a
Digital Input Function: Seat Orientation: Abnormal appropriate default value. This may result in message contains an invalid or unavailable valid value.
7D.09 520334 9 Amber warning Flashing Update Rate reduced vehicle operation. Contact maintenance for troubleshooting value. Check the can bus communication.
TCON ERROR CODES & DESCRIPTIONS
Revision 2.54 - Firmware Version 2.04
Date: 3/3/2021
ERROR CODE
DANA [HEX] SAE J1939 DM 1 STATUS LAMP ERROR DESCRIPTION TCON ACTION DRIVER ACTION FAILURE CAUSE TROUBLESHOOTING
SPN FMI
TCON will continue normal operation, but
the value of the input function Seat
Orientation will be replaced by the default The expected value for the input function
value. Seat Orientation received by the Check the source signal from the CAN message
Digital Input Function: Seat Orientation: Received This will result in reduced operation of the Contact maintenance for troubleshooting corresponding CAN message contains an containing the input function Seat Orientation
7D.13 520334 19 Amber warning Flashing Network Data in Error vehicle. invalid or unavailable value. for requesting a valid value.
The TCON will flag the fault and the state of The expected value for the input function, Check the source signal from the CAN message
the function will be replaced by an received by the corresponding CAN containing the input function for requesting a
Digital Input Function: Reduced vehicle speed: Abnormal appropriate default value. This may result in message contains an invalid or unavailable valid value.
7E.09 520335 9 Amber warning Flashing Update Rate reduced vehicle operation. Contact maintenance for troubleshooting value. Check the can bus communication.
TCON will continue normal operation, but
the value of the input function Reduced
vehicle speed will be replaced by the The expected value for the input function
default value. Reduced vehicle speed received by the Check the source signal from the CAN message
Digital Input Function: Reduced vehicle speed: Received This will result in reduced operation of the corresponding CAN message contains an containing the input function Reduced vehicle
7E.13 520335 19 Amber warning Flashing Network Data in Error vehicle. Contact maintenance for troubleshooting invalid or unavailable value. speed for requesting a valid value.
Digital Input Function: Redundant Vehicle reduced
7F.09 520336 9 Amber warning Flashing speed: Abnormal Update Rate
The TCON will flag the fault and the state of The expected value for the input function, Check the source signal from the CAN message
the function will be replaced by an received by the corresponding CAN containing the input function for requesting a
Digital Input Function: Start 1st/2nd: Abnormal Update appropriate default value. This may result in message contains an invalid or unavailable valid value.
80.09 520337 9 Amber warning Flashing Rate reduced vehicle operation. Contact maintenance for troubleshooting value. Check the can bus communication.
TCON will continue normal operation, but
the value of the input function Start
1st/2nd will be replaced by the default The expected value for the input function
value. Start 1st/2nd received by the corresponding Check the source signal from the CAN message
Digital Input Function: Start 1st/2nd: Received Network This will result in reduced operation of the CAN message contains an invalid or containing the input function Start 1st/2nd for
80.13 520337 19 Amber warning Flashing Data in Error vehicle. Contact maintenance for troubleshooting unavailable value. requesting a valid value.
The TCON will flag the fault and the state of The expected value for the input function, Check the source signal from the CAN message
the function will be replaced by an received by the corresponding CAN containing the input function for requesting a
Digital Input Function: Operator Seated: Abnormal appropriate default value. This may result in message contains an invalid or unavailable valid value.
81.09 520338 9 Amber warning Flashing Update Rate reduced vehicle operation. Contact maintenance for troubleshooting value. Check the can bus communication.
The TCON will flag the fault and the state of The expected value for the input function, Check the source signal from the CAN message
the function will be replaced by an received by the corresponding CAN containing the input function for requesting a
Digital Input Function: 4WD/2WD feedback loop: appropriate default value. This may result in message contains an invalid or unavailable valid value.
26.09 520339 9 Amber warning Flashing Abnormal Update Rate reduced vehicle operation. Contact maintenance for troubleshooting value. Check the can bus communication.
The TCON will flag the fault and the state of Check the source signal from the CAN message
the function will be replaced by an containing the input function for requesting a
Digital Input Function: 4WD/2WD: Data Valid but Above appropriate default value. This may result in The feedback shows 4WD but 2WD output valid value.
26.0F 520339 15 Amber warning Flashing Normal Operational Range - Least Severe reduced vehicle operation. Contact maintenance for troubleshooting is activated Check the can bus communication.
TCON ERROR CODES & DESCRIPTIONS
Revision 2.54 - Firmware Version 2.04
Date: 3/3/2021
ERROR CODE
DANA [HEX] SAE J1939 DM 1 STATUS LAMP ERROR DESCRIPTION TCON ACTION DRIVER ACTION FAILURE CAUSE TROUBLESHOOTING
SPN FMI
TCON will continue normal operation, but
the value of the input function 4WD/2WD
feedback loop will be replaced by the The expected value for the input function
default value. 4WD/2WD feedback loop received by the Check the source signal from the CAN message
Digital Input Function: 4WD/2WD feedback loop: This will result in reduced operation of the corresponding CAN message contains an containing the input function 4WD/2WD
26.13 520339 19 Amber warning Flashing Received Network Data in Error vehicle. Contact maintenance for troubleshooting invalid or unavailable value. feedback loop for requesting a valid value.
The TCON will flag the fault and the state of The expected value for the input function, Check the source signal from the CAN message
the function will be replaced by an received by the corresponding CAN containing the input function for requesting a
appropriate default value. This may result in message contains an invalid or unavailable valid value.
87.09 520344 9 Amber warning Flashing Digital Input Function: Exhaust: Abnormal Update Rate reduced vehicle operation. Contact maintenance for troubleshooting value. Check the can bus communication.
The TCON will flag the fault and the state of The expected value for the input function, Check the source signal from the CAN message
the function will be replaced by an received by the corresponding CAN containing the input function for requesting a
appropriate default value. This will make message contains an invalid or unavailable valid value.
88.09 520345 9 Amber warning Flashing Digital Input Function: Retarder: Abnormal Update Rate the retarder functionality unavailable. Contact maintenance for troubleshooting value. Check the can bus communication.
TCON ERROR CODES & DESCRIPTIONS
Revision 2.54 - Firmware Version 2.04
Date: 3/3/2021
ERROR CODE
DANA [HEX] SAE J1939 DM 1 STATUS LAMP ERROR DESCRIPTION TCON ACTION DRIVER ACTION FAILURE CAUSE TROUBLESHOOTING
SPN FMI
The TCON will flag the fault and the state of The expected value for the input function
the function will be replaced by an Retarder received by the corresponding Check the source signal from the CAN message
Digital Input Function: Retarder: Received Network Data appropriate default value. This will make CAN message contains an invalid or containing the input function Retarder for
88.13 520345 19 Amber warning Flashing in Error the retarder functionality unavailable. Contact maintenance for troubleshooting unavailable value. requesting a valid value.
The TCON will flag the fault and the state of The expected value for the input function, Check the source signal from the CAN message
the function will be replaced by an received by the corresponding CAN containing the input function for requesting a
appropriate default value. This may result in message contains an invalid or unavailable valid value.
89.09 520346 9 Amber warning Flashing Digital Input Function: Towing: Abnormal Update Rate reduced vehicle operation. Contact maintenance for troubleshooting value. Check the can bus communication.
The TCON will flag the fault and the state of The expected value for the input function, Check the source signal from the CAN message
the function will be replaced by an received by the corresponding CAN containing the input function for requesting a
Digital Input Function: Towing Feedback 1: Abnormal appropriate default value. This may result in message contains an invalid or unavailable valid value.
8A.09 520347 9 Amber warning Flashing Update Rate reduced vehicle operation. Contact maintenance for troubleshooting value. Check the can bus communication.
TCON will continue normal operation, but
the value of the input function Towing
Feedback 1 will be replaced by the default The expected value for the input function
value. Towing Feedback 1 received by the Check the source signal from the CAN message
Digital Input Function: Towing Feedback 1: Received This will result in reduced operation of the corresponding CAN message contains an containing the input function Towing Feedback
8A.13 520347 19 Amber warning Flashing Network Data in Error vehicle. Contact maintenance for troubleshooting invalid or unavailable value. 1 for requesting a valid value.
The TCON will flag the fault and the state of The expected value for the input function, Check the source signal from the CAN message
the function will be replaced by an received by the corresponding CAN containing the input function for requesting a
Digital Input Function: Towing Feedback 2: Abnormal appropriate default value. This may result in message contains an invalid or unavailable valid value.
8B.09 520348 9 Amber warning Flashing Update Rate reduced vehicle operation. Contact maintenance for troubleshooting value. Check the can bus communication.
TCON will continue normal operation, but
the value of the input function Towing
Feedback 2 will be replaced by the default The expected value for the input function
value. Towing Feedback 2 received by the Check the source signal from the CAN message
Digital Input Function: Towing Feedback 2: Received This will result in reduced operation of the corresponding CAN message contains an containing the input function Towing Feedback
8B.13 520348 19 Amber warning Flashing Network Data in Error vehicle. Contact maintenance for troubleshooting invalid or unavailable value. 2 for requesting a valid value.
The expected value for the input function, Check the source signal from the CAN message
The value of the shiftlever function will be received by the corresponding CAN containing the input function for requesting a
Digital Input Function: Redundant neutral: Abnormal overrruled by neutral selection. TCON will Stop the vehicle and contact maintenance for message contains an invalid or unavailable valid value.
8C.09 520349 9 Stop Lamp Flashing Update Rate revert to shutdown mode. troubleshooting value. Check the can bus communication.
The TCON will flag the fault and the state of The expected value for the input function, Check the source signal from the CAN message
the function will be replaced by an received by the corresponding CAN containing the input function for requesting a
appropriate default value. This may result in message contains an invalid or unavailable valid value.
8D.09 520350 9 Amber warning Flashing Digital Input Function: Eco Mode: Abnormal Update Rate reduced vehicle operation. Contact maintenance for troubleshooting value. Check the can bus communication.
ERROR CODE
DANA [HEX] SAE J1939 DM 1 STATUS LAMP ERROR DESCRIPTION TCON ACTION DRIVER ACTION FAILURE CAUSE TROUBLESHOOTING
SPN FMI
The TCON will flag the fault and the state of The expected value for the input function, Check the source signal from the CAN message
the function will be replaced by an received by the corresponding CAN containing the input function for requesting a
Digital Input Function: Enhanced vehicle speed appropriate default value. This may result in message contains an invalid or unavailable valid value.
8E.09 520351 9 Amber warning Flashing resolution: Abnormal Update Rate reduced vehicle operation. Contact maintenance for troubleshooting value. Check the can bus communication.
The TCON will flag the fault and the state of The expected value for the input function Check the source signal from the CAN message
the function will be replaced by an "Loader Mode", received by the containing the input function for requesting a
Digital Input Function: Loader Mode: Abnormal Update appropriate default value. This may result in corresponding CAN message contains an valid value.
8F.09 520354 9 Amber warning Flashing Rate reduced vehicle operation. Contact maintenance for troubleshooting invalid or unavailable value. Check the can bus communication.
The TCON will flag the fault and the state of The expected value for the input function Check the source signal from the CAN message
the function will be replaced by an "Kickdown", received by the corresponding containing the input function for requesting a
appropriate default value. This may result in CAN message contains an invalid or valid value.
90.09 520355 9 Amber warning Flashing Digital Input Function: Kickdown Abnormal Update Rate reduced vehicle operation. Contact maintenance for troubleshooting unavailable value. Check the can bus communication.
The TCON will flag the fault and the state of The expected value for the input function, Check the source signal from the CAN message
the function will be replaced by an received by the corresponding CAN containing the input function for requesting a
Digital Input Function: Inching Mode Selection Abnormal appropriate default value. This may result in message contains an invalid or unavailable valid value.
91.09 520356 9 Amber warning Flashing Update Rate reduced vehicle operation. Contact maintenance for troubleshooting value. Check the can bus communication.
TCON will continue normal operation, but
the value of the input function "Inching
Mode Select" will be replaced by the default The expected value for the input function
value. "Inching mode select" received by the Check the source signal from the CAN message
Digital Input Function: Inching Mode Selection Received This will result in reduced operation of the corresponding CAN message contains an containing the input function "inching mode
91.13 520356 19 Amber warning Flashing Network Data in Error vehicle. Contact maintenance for troubleshooting invalid or unavailable value. select" for requesting a valid value.
TCON ERROR CODES & DESCRIPTIONS
Revision 2.54 - Firmware Version 2.04
Date: 3/3/2021
ERROR CODE
DANA [HEX] SAE J1939 DM 1 STATUS LAMP ERROR DESCRIPTION TCON ACTION DRIVER ACTION FAILURE CAUSE TROUBLESHOOTING
SPN FMI
The TCON will flag the fault and the state of The expected value for the input function, Check the source signal from the CAN message
the function will be replaced by an received by the corresponding CAN containing the input function for requesting a
Digital Input Function: declutch enable/disable Selection appropriate default value. This may result in message contains an invalid or unavailable valid value.
92.09 520357 9 Amber warning Flashing Abnormal Update Rate reduced vehicle operation. Contact maintenance for troubleshooting value. Check the can bus communication.
The TCON will flag the fault and the state of The expected value for the input function, Check the source signal from the CAN message
the function will be replaced by an received by the corresponding CAN containing the input function for requesting a
Digital Input Function: Inhibit Upshift: Abnormal Update appropriate default value. This may result in message contains an invalid or unavailable valid value.
93.09 520358 9 Amber warning Flashing Rate reduced vehicle operation. Contact maintenance for troubleshooting value. Check the can bus communication.
The TCON will flag the fault and the state of The expected value for the input function, Check the source signal from the CAN message
the function will be replaced by an received by the corresponding CAN containing the input function for requesting a
Digital Input Function: Neutral Lock: Abnormal Update appropriate default value. This may result in message contains an invalid or unavailable valid value.
82.09 520359 9 Amber warning Flashing Rate reduced vehicle operation. Contact maintenance for troubleshooting value. Check the can bus communication.
The TCON will flag the fault and the state of The expected value for the input function, Check the source signal from the CAN message
the function will be replaced by an received by the corresponding CAN containing the input function for requesting a
appropriate default value. This may result in message contains an invalid or unavailable valid value.
83.09 520360 9 Amber warning Flashing Digital Input Function: New Idle: Abnormal Update Rate reduced vehicle operation. Contact maintenance for troubleshooting value. Check the can bus communication.
The TCON will flag the fault and the state of The expected value for the input function, Check the source signal from the CAN message
the function will be replaced by an received by the corresponding CAN containing the input function for requesting a
Digital Input Function: Upshift Command: Abnormal appropriate default value. This may result in message contains an invalid or unavailable valid value.
60.09 520363 9 Amber warning Flashing Update Rate reduced vehicle operation. Contact maintenance for troubleshooting value. Check the can bus communication.
The expected value for the input function, Check the source signal from the CAN message
received by the corresponding CAN containing the input function for requesting a
Digital Input Function: Motor status bit: Abnormal TCON will revert to transmission shutdown message contains an invalid or unavailable valid value.
61.09 520364 9 Stop Lamp Flashing Update Rate mode. Contact maintenance for troubleshooting value. Check the can bus communication.
TCON ERROR CODES & DESCRIPTIONS
Revision 2.54 - Firmware Version 2.04
Date: 3/3/2021
ERROR CODE
DANA [HEX] SAE J1939 DM 1 STATUS LAMP ERROR DESCRIPTION TCON ACTION DRIVER ACTION FAILURE CAUSE TROUBLESHOOTING
SPN FMI
TCON will revert to shutdown mode. This - Check the wiring between the controller and
will result in inoperability of the vehicle. the speed sensors.
TCON will only resume normal operation - Check the speed sensors.
redundant shutdown path turbine (RSP): Data Valid but once the error is cleared and TCON is Stop the vehicle and contact maintenance for Speed sensor failure, - Check the speed sensor positions.
22.01 520379 1 Stop Lamp Flashing Below Normal Operational Range - Most Severe restarted. troubleshooting Supply pressure to transmission too low - Check supply pressure to the transmission.
TCON will revert to shutdown mode. This
will result in inoperability of the vehicle. - Check the wiring between the controller and
TCON will only resume normal operation Speed sensor failure, the speed sensors.
redundant shutdown path drum (RSP): Data Valid but once the error is cleared and TCON is Stop the vehicle and contact maintenance for Too much drag because of thick oil, - Check the speed sensors.
22.00 520379 0 Stop Lamp Flashing Above Normal Operational Range - Most Severe restarted. troubleshooting Sticking or burnt clutch - Check the speed sensor positions.
TCON ERROR CODES & DESCRIPTIONS
Revision 2.54 - Firmware Version 2.04
Date: 3/3/2021
ERROR CODE
DANA [HEX] SAE J1939 DM 1 STATUS LAMP ERROR DESCRIPTION TCON ACTION DRIVER ACTION FAILURE CAUSE TROUBLESHOOTING
SPN FMI
ERROR CODE
DANA [HEX] SAE J1939 DM 1 STATUS LAMP ERROR DESCRIPTION TCON ACTION DRIVER ACTION FAILURE CAUSE TROUBLESHOOTING
SPN FMI
ERROR CODE
DANA [HEX] SAE J1939 DM 1 STATUS LAMP ERROR DESCRIPTION TCON ACTION DRIVER ACTION FAILURE CAUSE TROUBLESHOOTING
SPN FMI
TCON will revert to shutdown. As this
message contains critical data, the vehicle - Check if the CAN message is sent correctly on
cannot be driven until the message the CAN bus.
becomes available again. Contact maintenance for troubleshooting The CAN message is not received within the - Check if the repetition rate of the CAN
CE.09 520398 9 Stop Lamp Flashing Can Message EM_to_TC_1: Abnormal Update Rate expected timeframe. message is fast enough.
ERROR CODE
DANA [HEX] SAE J1939 DM 1 STATUS LAMP ERROR DESCRIPTION TCON ACTION DRIVER ACTION FAILURE CAUSE TROUBLESHOOTING
SPN FMI
ERROR CODE
DANA [HEX] SAE J1939 DM 1 STATUS LAMP ERROR DESCRIPTION TCON ACTION DRIVER ACTION FAILURE CAUSE TROUBLESHOOTING
SPN FMI
TCON is limiting the vehicle speed to the Slow down the vehicle, until that the vehicle
Exceed Reduced vehicle speed : Data Valid but Above maximum or reduced vehicle speed limit, speed comes below the maximum or reduced The vehicle speed is above the maximum
E3.10 520420 16 Protection Lamp Normal Operational Range - Moderately Severe but detects a higher vehicle speed. vehicle speed limit. vehicle speed limit. none
The controller detected an abnormal
accelleration, and will disable the
Exceed Abnormal Accelaration/Deceleration: Data Valid The driver should slow down the engine, in automatiic shifting for a certain time.
E4.0F 520421 15 Protection Lamp but Above Normal Operational Range - Least Severe An abnormal acceleration is detected. order that the wheels can not spin any more. none
The controller detected an abnormal
decelleration, and will disable the
Exceed Abnormal Accelaration/Deceleration: Data Valid The driver should slow down, in order that the automatiic shifting for a certain time.
E4.11 520421 17 Protection Lamp but Below Normal Operational Range - Least Severe An abnormal decelleration is detected. wheels can not slip any more. none
The driver should take place in the operator seat
Operator is not seated with shiftlever not in and confirm his presence (cycle the shiftlever The controller detected that the operator is - Check operator seat switch
Exceed Operator seated conditions: Special Instruction neutral and/or the parking brake not through neutral and/or release the throttle not seated with the shiftlever not in neutral - Check parking brake
E6.0E 520422 14 Protection Lamp (consult documentation) activated. pedal) and/or the parking brake not activated. - Check shift lever
TCON detects that the turbine,
Exceed transmission speed limits: Data Valid but Above TCON will force engine idle to prevent Slow down the vehicle, in order that the speed intermediate or output speed is above its
E7.0F 520423 15 Protection Lamp Normal Operational Range - Least Severe damage. drops below the maximum speed limit. limit. none
Exceed Low High range conditions: Data Valid but Above Condition to change low high range selector Brake and stop the vehicle until this exceed code TCON detected that the vehicle is still
E8.0F 520424 15 Protection Lamp Normal Operational Range - Least Severe not furfilled. Vehicle has to stand still. is no longer present. moving. none
Condition to change from 4wd to 2wd or
Exceed 4WD/2WD drive conditions: Data Valid but Above visa versa not furfilled. Vehicle has to stand Brake and stop the vehicle until this exceed code TCON detected that the vehicle is still
E9.0F 520425 15 Protection Lamp Normal Operational Range - Least Severe still. is no longer present. moving. none
TCON ERROR CODES & DESCRIPTIONS
Revision 2.54 - Firmware Version 2.04
Date: 3/3/2021
ERROR CODE
DANA [HEX] SAE J1939 DM 1 STATUS LAMP ERROR DESCRIPTION TCON ACTION DRIVER ACTION FAILURE CAUSE TROUBLESHOOTING
SPN FMI
ERROR CODE
DANA [HEX] SAE J1939 DM 1 STATUS LAMP ERROR DESCRIPTION TCON ACTION DRIVER ACTION FAILURE CAUSE TROUBLESHOOTING
SPN FMI
ERROR CODE
DANA [HEX] SAE J1939 DM 1 STATUS LAMP ERROR DESCRIPTION TCON ACTION DRIVER ACTION FAILURE CAUSE TROUBLESHOOTING
SPN FMI
During initialization the TCON detected that - If this occurs right after performing a firmware
the logging part of the data flash is corrupt. update of the TCON, this should be solved by
Turn power off and restart the vehicle. If the All functional logging data (like travelled performing a normal power down of the TCON.
problem persists, contact maintenance for distance etc..) but also error logging data - if the problem persists, contact Dana Belgium
F3.0A 520435 10 Stop Lamp Flashing APC Data Flash partially corrupt: parameter group 10. TCON reverts to shutdown mode. troubleshooting. will be lost and reset to zero. N.V.
During initialization the TCON detected that - If this occurs right after performing a firmware
the logging part of the data flash is corrupt. update of the TCON, this should be solved by
Turn power off and restart the vehicle. If the All functional logging data (like travelled performing a normal power down of the TCON.
problem persists, contact maintenance for distance etc..) but also error logging data - if the problem persists, contact Dana Belgium
F3.0B 520435 11 Stop Lamp Flashing APC Data Flash partially corrupt: parameter group 11. TCON reverts to shutdown mode. troubleshooting. will be lost and reset to zero. N.V.
ERROR CODE
DANA [HEX] SAE J1939 DM 1 STATUS LAMP ERROR DESCRIPTION TCON ACTION DRIVER ACTION FAILURE CAUSE TROUBLESHOOTING
SPN FMI
F7.00 520439 0 Amber warning Flashing Severe engine limitation active due to low temperature. TCON limits the engine to the lowest limit. Heat up transmission.
F7.01 520439 1 Amber warning Flashing Engine limitation active due to low temperature. TCON limits the engine. Heat up transmission.
Action will depend on the type of Stop the vehicle, turn power off and restart the
(configuration) error, but in most cases vehicle. If the problem persists, contact An unexpected event occured that was Take note of the reported error code and
FX.XX 520432 - 520447 XX Stop Lamp Flashing Assert error: DANA reserved code TCON.L will revert to shutdown mode maintenance for troubleshooting detected by the TCON.L firmware. contact a DANA representative.
CALIBRATION
ERROR CODE EXPLANATION
x = 0 Pressure to current
Calibration.
Ex.06 [DEC] x = 1 Touch pressure Calibration During calibration the turbine speed signal does not At fill area calibration, timeout on full
Ex.06 [HEX] x = 2 Optimise fill time reach a minimum value. turbine pulldown.
x = 0 Pressure to current
Error detected, during P2mA, TchPrs or
Calibration.
fillArea.
Ex.10 [DEC] x = 1 Touch pressure Calibration
Ex.0A [HEX] x = 2 Optimise fill time Transmission failure during calibration.
E1.27 [DEC] Turbine speed does not reach value = 0 rpm at end of during touch pressure when at full pressure,
E1.1B [HEX] Touch pressure calibration. closing phase of the touch pressure calibration the turbine speed > 5 rpm.
E1.28 [DEC] turbine speed <= 5 rpm at end of touch
E1.1C [HEX] Release pressure calibration. Clutch does not close before release calibration runs. phase
TCON ERROR CODES & DESCRIPTIONS
Revision 2.54 - Firmware Version 2.04
Date: 3/3/2021
ERROR CODE
DANA [HEX] SAE J1939 DM 1 STATUS LAMP ERROR DESCRIPTION TCON ACTION DRIVER ACTION FAILURE CAUSE TROUBLESHOOTING
SPN FMI
E1.29 [DEC] Turbine speed signal does not reach a high enough value turbine speed <= 5 rpm at end of release
E1.1D [HEX] Touch pressure calibration. during release phase of the touch pressure calibration. phase
E0.27 [DEC]
E0.1B [HEX] Pressure to current Calibration. Measured pressure points do not allow interpolation.
E0.30 [DEC] maximum number of retries reached during P2mA for
E0.1E [HEX] Pressure to current Calibration. the peak to peak pressure.
E0.31 [DEC] During P2mA routine a pressure drop of more than 1 bar
E0.1F [HEX] Pressure to current Calibration. is detected.
E0.32 [DEC]
E0.20 [HEX] Pressure to current Calibration. At start of P2mA, the pressure signal is too high.