Professional Documents
Culture Documents
Ef17155p03 Volvo Ew160b Grab 050506
Ef17155p03 Volvo Ew160b Grab 050506
Groeneveld reserves the right to change parts at any time, without prior or direct notice to the customer. The
contents of this manual may also be changed without prior notice.
This manual applies to the standard version of the product. Groeneveld cannot accept liability for any damage
arising from the use of specifications other than that supplied.
You are requested to contact Groeneveld technical service for information concerning adjustment, maintenance
work or repairs that is not described in this manual.
Whilst this manual has been prepared with the greatest possible care Groeneveld cannot accept responsibility for
any errors of the concequences of such errors.
Excavator Volvo EW160B grab
1.
q^_ib=lc=`lkqbkqp
1. Preface - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 5
1.1. General information - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 6
1.2. Use of symbols - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 6
1.3. Safety precautions - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 7
1.4. General fitting instructions - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 7
2. System lay-out - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 9
2.1. F174486 Twin 4+4-port block, complete - - - - - - - - - - - - - - - - - - - - - - 12
2.2. F174487 Twin 14-port block, complete - - - - - - - - - - - - - - - - - - - - - - - 14
5. Electrical components - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 25
5.1. F175001 Electronics installation kit Volvo EW160B grab - - - - - - - - - - - 26
6. Distribution blocks - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 29
6.1. F174490 Installation kit Twin 4+4-port block / F174486 B1 - - - - - - - - - 30
6.2. F173046 Installation kit Twin 14-port block / F174487 B2 - - - - - - - - - - 34
8. Parameter settings - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 43
1.
2.
PREFACE
Date of issue: May 2006
EF17155P03 Preface 5
Excavator Volvo EW160B grab
Volvo
19 x F174485 - EF17155P03
EW160B grab
Distribution block
BK Black
BN Brown
BU Blue
RD Red
GY Grey
YE Yellow
Date of issue: May 2006
BR Brass
PA Polyamide
SST Stainless steel
ST-YG Yellow passivated steel
ST-G Galvanised steel
6 Preface EF17155P03
Excavator Volvo EW160B grab
General:
• Always keep your work area clean.
During installation
• Prevent dirt from entering the system during installation.
• Use clean tools.
• Clean the machine at points, where the pump and the distribution blocks
have to be installed. Even small pollution can cause failure of the system!
• Even if stud couplings or plugs are not provided with an O-ring sealing or
sealing ring, use teflon tape or a liquid sealing agent.
Date of issue: May 2006
EF17155P03 Preface 7
Excavator Volvo EW160B grab
Notes
8 Preface EF17155P03
Excavator Volvo EW160B grab
2.
3.
SYSTEM LAY-OUT
Date of issue: May 2006
Parts list
The Twin-system for the Volvo EW160B grab comprises the following parts:
Parts list
Parts list
Notes
3.
4.
GREASE POINT LOCATION
Date of issue: May 2006
Notes
4.
5.
GREASE PUMP INSTALLATION
Date of issue: May 2006
Parts list
Notes
5.
6.
ELECTRICAL COMPONENTS
Date of issue: May 2006
Parts list
6.
7.
DISTRIBUTION BLOCKS
Date of issue: May 2006
Parts list
2 3
6 7
Date of issue: May 2006
Parts list
9 13
8 12
Date of issue: May 2006
10 11
16
10 12
13
11
14
19
18
15
17
19
Date of issue: May 2006
Notes
7.
8.
INSTALLATION MAIN LINE
Date of issue: May 2006
Parts list
8.
9.
PARAMETER SETTINGS
Date of issue: May 2006
Parameter settings
9.
10.
TESTING OF THE SYSTEM
Date of issue: May 2006
Warning
Only operate machine when fully familiar with the controls and permission
of the person in charge at the working place.
De-aerate pipe A
• Start the pump manually with the Gina; leave the 5/2 magnet valve non-
excited (exit A).
• Close the distribution blocks with an end-plug as soon as main pipe (A) is
completely clear of air and dirt.
• Stop the pump.
• Remove main pipe A.
De-aerate pipe B
• Mount main pipe (B) on exit A of the pump.
• Start the pump manually with the Gina; leave the 5/2 magnet valve non-
excited (exit A).
• Close the distribution blocks with an end-plug as soon as main pipe (B) is
completely clear of air and dirt.
• Stop the pump.
• Connect main pipe (B) to exit B and main pipe (A) to exit A.
Accelerated test
• Start an accelerated test by means of the test button on the pump or with the
GINA.
• Check the main pipe for leakage.
• Check if all the grease points are provided with grease.
• Terminate the accelerated test by switching off the ignition.