Professional Documents
Culture Documents
1 7 6 5 9 2 10 8 2 1 9 4a 4b 3
Function
By rotation of the gears inside the pump, the pressure fluid In radial direction, the gear chambers are closed by gear mes-
(usually hydraulic oil) is drawn into the cavity between the pi- hing and the filler piece. In the axial direction, the axial plates
nion and internal gear. Optimized cross-sectional areas on seal the pressure chamber with the minimal possible gap. This
suction side as well as on pressure side allow operation over design minimizes volume losses and increases efficiency.
a wide range of speed.
2
Technical Data
Design internal gear pump with radial and axial sealing gap compensation
Type IPVP
Input pressure 0.8…3 bar absolute pressure (at start up for short time 0.6 bar)
Preload pressure, pressure port (in reversing mode) for details please contact Voith Turbo H + L Hydraulic
Viscosity range of the pressure fluid 10 ... 100 mm2s-1 (cSt), up to nmax
Required purity of the pressure fluid according to NAS 1638 Class 19 / 17 / 14 (ISO 4406), Class 8 (NAS 1638)
Filtration filtration quotient min. β20 ≥ 75, recommended β10 ≥ 100 (longer life)
Calculations
Q · Δp
P= [kW]
Power 600 · ηg
n speed [min-1]
ηv volumetric efficiency
ηg overall efficiency
3
Characteristics
IPVP 3 – 3.5 3.6 400 3 600 5.4 13.0 330 345 0.34
IPVP 3 – 6.3 6.4 400 3 600 9.6 23.0 330 345 0.49
IPVP 6 – 100 101.3 400 2 600 151.9 263.4 250 300 36.10
IPVP 6 – 125 126.2 400 2 600 189.3 328.1 210 250 43.70
IPVP 7 – 125 125.8 400 2 500 188.7 314.5 300 330 84.05
IPVP 7 – 160 160.8 400 2 500 241.2 402.0 280 315 102.60
IPVP 7 – 200 202.7 400 2 500 304.0 503.8 250 300 119.00
IPVP 7 – 250 251.7 400 2 500 377.5 629.3 210 250 144.50
• Pumping of mineral oils with a viscosity of 20…40 mm2s-1 • Peak pressures apply for 15% of operating time with a ma-
• An input pressure of 0.8…3.0 bar absolute ximum cycle time of 1 minute.
• Please consult us about peak pressures at non-standard
speeds.
• Due to production tolerances, the pump volume may be re-
duced by up to 1.5%.
• The values for min. and max. speed are dependent on
pressure! Please see exact dates on the diagrams from the
following pages. At speeds below 400 1/min the pressure
must be reduced according to the curve. At high speeds,
this may be the case.
• The pump can be temporarily operating below the specified
minimum speed in pressure-hold function. The holding time
and the rotational speed required for this purpose is ob-
tained in dependence of the viscosity and of the operating
pressure levels. For design details please contact Voith Tur-
bo H + L Hydraulic.
4
Diagram IPVP 3, IPVP 4 - Continuous pressure depending on the speed
375
350 IPVP 3
IPVP 4-13
325
IPVP 4-16
300 IPVP 4-20
275
IPVP 4-25
250
225
Continuous pressure [bar]
200
IPVP 4-32
175
150
125
100
75
50
max. speed IPVP 3 and 4
25
0
0 250 500 750 1000 1250 1500 1750 2000 2250 2500 2750 3000 3250 3500 3750 4000
Speed [RPM]
IPVP 5
350
325
IPVP 5-32
300
IPVP 5-40
275
250
225
IPVP 5-50
Continuous pressure [bar]
200
175
IPVP 5-64
150
125
100
75
50
max. speedl IPVP 5
25
0
0 250 500 750 1000 1250 1500 1750 2000 2250 2500 2750 3000 3250
Speed [RPM]
5
Diagram IPVP 6 - Continuous pressure depending on the speed
IPVP 6
325
300
IPVP 6-64
275
IPVP 6-80
250
225
175
150
IPVP 6-125
125
100
75
50
max. speed IPVP 6
25
0
0 250 500 750 1000 1250 1500 1750 2000 2250 2500 2750
Speed [RPM]
IPVP 7
325
300
275
IPVP 7-125
250
225
IPVP 7-160
200
Continuous pressure [bar]
175
IPVP 7-200
150
IPVP 7-250
125
100
75
50
max. speed IPVP 7
25
0
0 250 500 750 1000 1250 1500 1750 2000 2250 2500 2750
Speed [RPM]
6
IPVP Size 3, Rotation and Dimensions
Rotation clockwise 51 43
11 ø 82.55 h8
(cw) M5 12.5
* c/2 c/2
6
53
5,8
11
47.2
35
106.4
43 19.5 S P 132
Rotation counter-
6 h9 e c
clockwise (ccw)
20.5
S P
ø 18 h7
r
Secondary shaft B: 80 Nm g
k
v w i
[mm] [mm] [mm] [mm] [mm] [mm] Thread [mm] [mm] Thread [kg]
* Ensure the M10x1 plug screw, hexagon socket SW5, is tightened to a torque of 10 Nm du-
ring pumping operation. Dependent on the pump position, filling or ventilation is possible
here prior to commissioning.
7
IPVP Size 3, Designs and Dimensions
Standard
Rotation clockwise, SAE 2-hole flange Parallel shaft with keyway connection
Suction connection
1 0 1
3030
Variants
Rotation counterclockwise, SAE 2-hole flange Parallel shaft with keyway connection
Suction connection
6 0 1
37,9
37,9
30
30
1111 109
109 2828
7 7 5 h9
5 h9 37,9
37,9
11
11
ø 80 h8
ø 80 h8
18
ø 16
ø 16 h7h7 18
3636
19,5
19,5 132
132
11 109 28
11 109 28
7 5 h9
7 5 h9
11
ø 80 h8
11
18
ø 80 h8
18
ø 16 h7
ø 16 h7
36
19,5 132 36
19,5 132
8
IPVP Size 4, Rotation and Dimensions
Rotation
64 60 13
clockwise (cw) c/2 c/2 ø 101.6 h8
* 9.5
M8x19
67
13.5
6.8
57.2
ø 88
48
146
S P
56 26 170
Rotation counter- 8 h9 e c
clockwise (ccw)
28
S P
ø 25 h7
I h
g
r
Allowed input torques:
k
Input shaft A: 335 Nm
Secondary shaft B: 190 Nm
v w i
[mm] [mm] [mm] [mm] [mm] [mm] Thread [mm] [mm] Thread [kg]
* Ensure the M10x1 plug screw, hexagon socket SW5, is tightened to a torque of 10 Nm du-
ring pumping operation. Dependent on the pump position, filling or ventilation is possible
here prior to commissioning.
9
IPVP Size 4, Designs and Dimensions
Standard
Rotation clockwise, SAE 2-hole flange Parallel shaft with keyway connection
Suction connection
1 7 1
3030
Variants
Rotation counterclockwise, SAE 2-hole flange Parallel shaft with keyway connection
Suction connection
6 7 1
37,9
37,9
30
30
1112 109
109 2828
7 7 5 h9
5 h9 37,9
37,9
11
11
ø 80 h8
ø 80 h8
18
ø 16
ø 16 h7h7 18
3636
36 19,5
19,5 132
132
11 109 28
12 109 28
7 5 h9
7 5 h9
11
ø 80 h8
11
18
ø 80 h8
18
ø 16 h7
ø 16 h7
36
19,5 132 36
36 19,5 132
10
IPVP Size 5, Rotation and Dimensions
Rotation 77 74
17
clockwise (cw) 6 c/2 c/2 ø 127 h8
*
M12x25
83
8.7
17.5
75.3
60
181
68 S P 210
20
Rotation counter-
10 h9 e c
clockwise (ccw)
35
S P
ø 32 h7
k
Input shaft A: 605 Nm
Secondary shaft B: 400 Nm
v w i
[mm] [mm] [mm] [mm] [mm] [mm] Thread [mm] [mm] Thread [kg]
* Ensure the M10x1 plug screw, hexagon socket SW5, is tightened to a torque of 10 Nm du-
ring pumping operation. Dependent on the pump position, filling or ventilation is possible
here prior to commissioning.
Note! In case of oil-immersed installation of the oil pump please consult us.
11
IPVP Size 5, Designs and Dimensions
Standard
Rotation clockwise, Suction connection SAE 2-hole flange Parallel shaft with keyway connection
1 0 1
3030
Variants
Rotation counterclockwise, Suction connection SAE 2-hole flange Parallel shaft with keyway connection
6 0 1
37.9
37.9
3030
37.9
37.9
1212 109
109 2828
77 5 5h9h9
11
11
ø 80 h8
ø 80 h8
18
18
ø ø1616h7h7
3636
3636 19.5
19.5 132
132
1212 109
109 2828
77 5 5h9h9
11
11
ø 80 h8
18
ø 80 h8
18
ø ø1616h7h7
12
IPVP Size 6, Rotation and Dimensions
Rotation 100 98 19
clockwise (cw) 6 c/2 c/2 ø 152.4 h8
*
M12 28
109
22
11,2
95
80
88 228.6
22 S P 264
Rotation counter- e c
12 h9
clockwise (ccw)
43
ø 40 h7 S P
k
Input shaft A: 1 050 Nm
Secondary shaft B: 780 Nm
v w i
[mm] [mm] [mm] [mm] [mm] [mm] Thread [mm] [mm] Thread [kg]
IPVP 6 – 100 158 35 27 50 77.8 42.9 M12 x 20 69.9 35.7 M12 x 20 33.0 14 15
IPVP 6 – 125 170 40 30 50 77.8 42.9 M12 x 20 69.9 35.7 M12 x 20 36.0 14 15
* Ensure the M10x1plug screw, hexagon socket SW5, is tightened to a torque of 10 Nm during
pumping operation. Dependent on the pump position, filling or ventilation is possible here prior to
commissioning.
13
IPVP Size 6, Designs and Dimensions
Standard
Rotation clockwise, Suction connection SAE 2-hole flange Parallel shaft with keyway connection
1 0 1
30
30
Variants
Rotation counterclockwise, Suction connection SAE 2-hole flange Parallel shaft with keyway connection
6 0 1
37.9
37.9
30
30
37.9
37.9
11
11 109
109 28
28
77 55h9
h9
11
11
h8
80 h8
18
18
ø 80
øø16
16h7
h7
ø
36
36
19.5
19.5 132
132
11
11 109
109 28
28
77 55h9
h9
11
11
ø 80 h8
ø 80 h8
18
18
øø16
16h7
h7
36
36
19.5
19.5 132
132
14
IPVP Size 7, Rotation and Dimensions
135
approx. ø130
264
22
13.7
114.3
6 ø 228.6
S P
104 264
e c
Rotation counter- 14 h9
clockwise (ccw)
M12 28
53.5
P
S
ø 50 h7
g
r
k
Allowed input torques:
Input shaft A:1 960 Nm
Secondary shaft B:1 200 Nm
v w i
[mm] [mm] [mm] [mm] [mm] [mm] Thread [mm] [mm] Thread [kg]
IPVP 7 – 125 152 48 30 50 77.8 42.9 M12 x 20 69.9 35.7 M12 x 20 46.5 14 15
* Ensure the M10x1 plug screw, hexagon socket SW5, is tightened to a torque of 10 Nm du-
ring pumping operation. Dependent on the pump position, filling or ventilation is possible
here prior to commissioning.
15
IPVP Size 7, Designs and Dimensions
Standard
Rotation clockwise, SAE-4-hole flange Parallel shaft with keyway connection
Suction connection
1 1 1
Variants
Rotation counterclockwise, SAE-4-hole flange Parallel shaft with keyway connection
Suction connection
6 1 1
16
Measurement Values - Airborne Noise Level, Efficiency
IPVP 3 – Airborne noise level (measuring location 1 m axial) IPVP 3 – Efficiency ηv and ηg
60 100
ηv
95
55
90
Efficiency ηv and ηg
Airborne noise level dB(A)
50 85 ηg
80
45
75
40 70
0 50 100 150 200 250 300 350 0 50 100 150 200 250 300 350
Characteristic curves:
IPVP 3 – 10 IPVP 3 – 8 IPVP 3 – 6.3 IPVP 3 – 5 IPVP 3 – 3.5
IPVP 4 – Airborne noise level (measuring location 1 m axial) IPVP 4 – Efficiency ηv and ηg
60 100
ηv
95
55
90
Efficiency ηv and ηg
ηg
Airborne noise level dB(A)
50 85
80
45
75
40 70
0 50 100 150 200 250 300 350 0 50 100 150 200 250 300 350
Operating pressure p [bar] Operating pressure p [bar]
Characteristic curves:
IPVP 4 – 32 IPVP 4 – 25 IPVP 4 – 20 IPVP 4 – 16 IPVP 4 – 13
IPVP 5 – Airborne noise level (measuring location 1 m axial) IPVP 5 – Efficiency ηv and ηg
70 100
ηv
95
65
90
Efficiency ηv and ηg
ηg
Airborne noise level dB(A)
60 85
80
55
75
50 70
0 50 100 150 200 250 300 350 0 50 100 150 200 250 300 350
Characteristic curves:
IPVP 5 – 64 IPVP 5 – 50 IPVP 5 – 40 IPVP 5 – 32
17
Measurement Values - Airborne Noise Level, Efficiency
IPVP 6 – Airborne noise level (measuring location 1 m axial) IPVP 6 – Efficiency ηv and ηg
75 100
ηv
95
70
Efficiency ηv and ηg
90
Airborne noise level dB(A)
ηg
65 85
80
60
75
55 70
0 50 100 150 200 250 300 350 0 50 100 150 200 250 300 350
Operating pressure p [bar] Operating pressure p [bar]
Characteristic curves:
IPVP 6 – 125 IPVP 6 – 100 IPVP 6 – 80 IPVP 6 – 64
IPVP 7 – Airborne noise level (measuring location 1 m axial) IPVP 7 – Efficiency ηv and ηg
80
100
ηv
95
75
Efficiency ηv and ηg
90
Airborne noise level dB(A)
ηg
70 85
80
65
75
60 70
0 50 100 150 200 250 300 350 0 50 100 150 200 250 300 350
Operating pressure p [bar] Operating pressure p [bar]
Characteristic curves:
IPVP 7 – 250 IPVP 7 – 200 IPVP 7 – 160 IPVP 7 – 125
Measurement Conditions:
Speed: 1.500 rpm / Viscosity of pressure fluid: 46 mm2s-1 / Operating temperature: 40 °C
Note:
Measurement taken in a low-noise room.
In a anechoic room. the measurements are approx. 5 dB(A) lower.
18
SAE-Flange, SAE J 518 C Code 61, single-piece
A
C
i
3)
Special design, deviation from SAE J 518 C Code 61
k D
B
thread [mm] [mm] [mm] seal ring [mm] [mm] thread [bar]
19
Multi-flow Pumps, Pump Combinations, Pump Combinations in Order of Type and Size
• IPVP pumps of identical or different sizes can be combined 1.Determine pressure ranges and define the appropriate
in multiflow pumps. pump serie(s).
• All sizes of the relevant pump volume are available as two- 2.Determine pump volume and select the appropriate size
or three-flow pumps; four-flow pumps must be designed 3. Define sequence of the pumps.
by Voith Turbo H + L Hydraulic. 4. Check the torques.
• The pumps are arranged in increasing order according to- 5. Determine rotation and suction.
frame size and delivery. 6. Specify mounting
Mounting, assembly
2 7
1 6 0 1 1
4
2 7
1 6 For designs and dimensions, see cata- For designs and dimensions,
log of the relevant pump series. see catalog of the relevant
pump series.
0 SAE-2-hole-flange
Special design 4 9 Special design
7 SAE-2-hole-flange (variant)
1 SAE-4-hole-flange
20
Type Code
IPVP 3 - 3.5 1 0 1
Shaft end
1 Parallel shaft with keyway
Mounting flange
0 SAE 2-hole
1 SAE 4-hole
7 SAE 2-hole, variant
Delivery
Size Delivery
3 3.5 5 6.3 8 10
4 13 16 20 25 32
5 32 40 50 64
6 64 80 100 125
Size
Type
21
90107-IPVP-DSH-D-EN-1612 | VTHL | Dimensions and illustrations non-committal, subject to change.
This is a translated document. Original language: german.
Legally binding language version of document: german.