Professional Documents
Culture Documents
Specifications:
402.344.4434 • www.brand-hyd.com
Schematics & Features 4-Way Directional Control
With Pressure Compensated Flow Control
PSDCF120M64LF1
MATERIALS:
• Cast Iron Body
• Buna N O’Rings
• IOSSO Plated Steel Spool
• Consult Factory for Stainless
Steel Spools
FEATURES:
• ADJUSTABLE PILOT OPERATED RELIEF VALVE is standard on every SDCF.
• FULL RANGE PRESSURE COMPENSATED by-pass type flow control valve built in.
• SDCF REDUCES the number of fittings, plumbing and potential leaks in hydraulic circuits.
• FINE POSITIVE METERING in either direction with the manual handle.
• PRECISION GROUND IOSSO PLATED SPOOL that assures long life.
• OPTIONAL O’RING PORTS to eliminate leakage.
SDCF REV(D)
D-2
General Information
SDCF – GENERAL INFORMATION:
The Brand, SDCF combines the features of a four-way directional control valve, a full range
pressure compensated by-pass type flow control valve, and an adjustable pilot operated pressure relief
valve all in one compact package. This valve reduces the number of fittings, plumbing and potential
leakage points in hydraulic circuits. The manual handle allows the customer to meter the flow out of
either port. Flow to the work port is directly proportional to the movement of the lever. Flow out of
each work port is constant regardless of load changes, this allows the customer to maintain smooth and
constant movement of a cylinder or motor. Every SDCF comes standard with a pilot operated relief
(1500 psi (102 bar) standard setting). The tank port must be plumbed directly back to tank.
SPOOL ACTION –
• Three-position detent (D) holds the spool in neutral and both active positions.
• Friction detent (F1) applies friction to the spool so that the spool does not move when the handle is
released either side of neutral, a detent groove clearly indicates neutral position.
• Spring center (S) returns the handle to neutral when the handle is released.
• Spring center detent (SD) springs back to neutral from one position and is mechanically detented in
the other position (flow out port A in detent).
• Detent spring center (DS) springs back to neutral from one position and is mechanically detented in
the other position (flow out port B in detent).
• Spring center friction detent (SF1) springs back to neutral from one direction and functions similar
to standard F1 in other direction (flow out port B in friction detent).
• Spring offset (SO) spring holds spool in one active position (flow out port B).
• Spring offset (SO2) spring holds spool in one active position (P to B in offset position, neutral and P toA).
• Rotary friction detent (E) applies friction to the spool as it is rotated so that the spool does not rotate
when the handle is released either side of neutral, a detent groove clearly indicates neutral position.
• Two-position detent (2D) P to B and neutral only.
• Two-position detent (D2) P to A and neutral only.
• Two-position friction (F2) P to A and neutral only.
• Normally closed electric switch (WC) used with (S), (F1) and (D) options only.
• Normally open electric switch (WO) used with (S), (F1) and (D) options only.
402.344.4434 • www.brand-hyd.com
D-3
Spool Schematics 4-Way Directional Control
With Pressure Compensated Flow Control
SPOOL SCHEMATICS:
A BA B A BA B
A BA B A BA B
A B A B
P TP T P TP T
P T P T P T P T
Tandem
Tandem Center
Center
Tandem (T) (T) -(T)
-
Center PowersPowers cylinder
cylinder
- Powers or motor
cylinderor motor
in motor
or in in Open CenterOpen
Open (O) -Center
Center (O) All of the
- All (O) ports
of - All ofare
the ports connected
are
the connected
ports are co
Tandem
bothboth Tandem
Center (T)
Center
- Powers
(T) - Powers
cylinder cylinder
or motor orinmotor in Open Center
Open (O)
Center
- All (O)
of the
- All
ports
of the
are ports
connected
are co
both
directions
directions
both
directions
both
directions
directions
(metering
(metering
(metering
(metering
(metering
capability
capability
capability
is very
capability
capability
is very
islimited).
very
limited).
is
is
very
very
limited).
limited).
limited).
tank
to tank
tank
when
when
when
the
the
tank
tankthe
spool
spool
when
when
spool
is
the
in
in
neutral.
isisinspool
the neutral.
spool is
neutral.
is
in
in
Allows
Allows
neutral.
neutral.
Allows
cylinde
Allow
cylinde
Allows
Pump unloads to tank when
Pump unloads to tankspool
when is in neutral.
spool is in neutral. move or move
motor orto motor
rotate to when spool
rotate when is in neutral.
spool is in
PumpPump unloads
unloads
Pump unloads
to or to tank
tank when when
to tankspool
whenspool
is spoolis in
is neutral.
ininneutral. inin
neutral. cylinder
movetoormove
motoror
move ortomotor
rotateto
motor rotate
towhen
rotate when
spool
when spool
is spool
in isisin
neutral.
Cylinder or motor
Cylinder blocked
motor when
blockedspoolwhen neutral.
spool neutral.
Cylinder
Cylinder or motor
Cylinder
or motor orblocked
motorblocked
blocked
when when
spool
when spool
in spool ininneutral.
neutral. neutral. in neutral. P T
P T
A
Tandem Center B(T)
A - PowersB cylinder or motor in A B
Open Center (O) -AAll of the
B ports are co
A BA
both directions (metering Bcapability is very limited). tank whenAthe spool
BA is in Bneutral. Allows
Pump unloads to tank when spool is in neutral. move or motor to rotate when spool is in
Cylinder or motor blocked when spool in neutral.
A B A B
P TP T P TP T
Fine Metering Spool P (M) -T PThe pressure
T drop in drop in Open Metering P (OM)
Spool T P- TheTneutral pressu
Fine Metering Spool (M) - The pressure Open Metering Spool (OM) - The neutr
FineFine
neutral Metering
Metering
Fine
isneutralMetering
Spool
higheristhen Spool
(M)
Spool
- (M) the
the then
higher (OM)The -and
(M) The pressure
pressure
- The
(TM)
(OM) pressure
drop
spools.
and drop in in
in spools.
(TM) drop Open Metering
Open
drop dropSpool
isMetering
Open
much lower
much(OM)
isMetering
Spoolthen(OM) - The
Spool
the
lower -then
(M) neutral
The
(OM)
spool.
the pressure
neutral
- (M)
The pressu
neutra
Extremel
spool.
neutral is
neutral
neutral
Requires higher is
then
is higher
external
Requires higher
the then
(OM)
thanvalves
locking
external the
and
the (OM)
locking (OM)
(TM)
tovalves and
spools.
(TM)
andcylinder,
hold (TM)
to spools.
holdspools.
cylinder, drop
dropfine is
is much much
drop
metering
fine is
lowerlower
much then
than the
control.
metering lower
the then
(M) spool.
(M)A spool.
Ports
control. andthe
Ports (M) Extreme
spool.
B areE
B Extremely
are open
A and
Requiresbecause
Requires
external external
locking valves
locking tovalves
hold cylinder,
to hold cylinder, fine metering
fine metering
control. control.
Ports A and
PortsB Aare
and
open
B are
P tobecause
because Tports
is blocked
ports A and
ports by the
B are
A and main
openB spool
(orificed)
are open but
in the valve
the
(orificed) in the fine (orificed)
metering(orificed)
incontrol. Ports
the neutral
in A and Bposition.
theposition.
neutral are open
because
neutral position. Aposition.
and
portsB Aare
Extremely and
PopenB are
fine T(orificed)
open
metering (orificed)
in the control.
control. in the (orificed)(orificed)
in the neutral
in theposition.
neutral
P position.
T
neutral
neutral
remains open
position.
neutral position.
Extremely
Extremely
center Extremely
due to metering fine
the fine metering
compensating spool (orificed) in the neutral position.
Spoolfine metering
control. drop
control. Open Metering Spool (OM) - The neutra
passage way. Requires external locking valves to in
Fine Metering (M) - The pressure
neutral is Ahigher B then
Aportsthe B (OM) and (TM) spools. drop is much lower then the (M) spool. E
holdRequires
cylinder,external
Abecause BAlocking BAvalves
and Btoare holdopen
cylinder, fine metering control. Ports A and B are
(orificed)
because ports A and B are open (orificed)fine
in the neutral position. Extremely in the (orificed) in the neutral position.
metering
neutralcontrol.
position. Extremely fine metering control.
A B
P TP T
Tandem Tandem P
MeteringMetering
Spool T P - Similiar
(TM) T
Spool (TM) - to (T) spool
Similiar to (T) spool
Tandem
except except much finer metering control.(T)
Tandem
Metering
much finerMetering
Spool
metering (TM)
Spool -
control.Similiar
(TM) -
The to
Similiar
pressure
Thespool
to (T) spool
pressure
except much
except
drop in neutral finer
muchmetering
drop inisneutral finer
lower then metering
control.
is lowerthe then control.
The
(M) spool. pressure
The
the (M)Cylinder pressure
spool. Cylinder
drop
or in neutral
motor drop
or inisneutral
blocked
motor lower
in is
then
neutral
blocked lower
thethen
inand (M) and
pump
neutral spool.
the (M)Cylinder
unloads
pump spool.
to Cylinder
unloads to
or motor
tank. orblocked
motor
tank. blocked
in neutral in
P and
neutral
pump
T and unloads
pump unloads
to to
tank. Tandem
tank. Metering Spool (TM) - Similiar to (T) spool
Tandem Metering Spool (TM) - Similar to (T) spool
except much finer metering control. The pressure
except much finer metering control. The pressure
drop in neutral is lower then the (M) spool. Cylinder
droporinmotor
neutral is lower
blocked than the
in neutral and(M)pumpspool.
unloads to
Cylinder
tank. or motor blocked in neutral and pump
unloads to tank.
SDCF REV(D)
D-4
Model Codes
SDCF – CREATING A MODEL CODE FOR SDCF’S:
SDCF 4
402.344.4434 • www.brand-hyd.com
D-5
Options & Accessories 4-Way Directional Control
With Pressure Compensated Flow Control
1.91" [48.5]
1.91" [48.5]
2.17" [55.0]
Ø1.39" [35.3]
External dimensions are the same for all kits listed above.
3.38" [86.0]
4.41" [111.9]
Ø1.37" [34.9]
External dimensions are the same for all kits listed above.
SDC-WC………………...Three-position detent kit with normally closed electric switch.
SDC-WO………………...Three-position detent kit with normally open electric switch.
SDC-F1WC……………..Ball friction detent with normally closed electric switch.
SDC-F1WO……………..Ball friction detent with normally open electric switch.
1.87" [47.5]
1.87" [47.5]
External dimensions are the same for all kits listed above.
SDCF REV(D)
D-6
Options & Accessories
SDCF – COMPLETE LIST OF KITS: (continued)
7.06" [179.3]
7.67" [194.7]
SDC-HJ…………………...J style handle kit. Lever handle pressurizes the A port when the handle
is pushed towards the valve body.
8.57" [217.6]
0.64" [16.1]
402.344.4434 • www.brand-hyd.com
D-7
Options & Accessories 4-Way Directional Control
With Pressure Compensated Flow Control
SDC-HL………………......L style handle kit. Lever handle pressurizes the B port when the handle is
pushed towards the valve body.
1.25" [31.8]
SDCF REV(D)
D-8
Flow And Pressure Information
SDCF – FLOW AND PRESSURE INFO:
402.344.4434 • www.brand-hyd.com
D-9
Dimensional Data 4-Way Directional Control
With Pressure Compensated Flow Control
0.94
A PORT
RELIEF ADJUSTMENT
8.8" [224]
B PORT
2.13" [54.0]
4.32" [109.8]
3.22" [81.8]
2.24" [56.8]
11.0" [278]
2.19" [55.6]
[56.8] 3.94" [100.0]