Professional Documents
Culture Documents
Kg / cm2g °C PSI g ºF
½” TO 1½” Pipes, Carbon Steel to IS: 1239 Part I, Heavy, ERW, Plain End
2” TO 6” Pipes, Carbon Steel to IS: 1239 Part I, Heavy, ERW, Beveled End
8” TO 10” Pipes, Carbon Steel to IS: 3589 Gr. 330, Welded, Beveled End, 6mm Thk.
½” TO1½” Nipples, Carbon Steel to A 106 Gr. B, Sch. 80, Seamless, Threaded one end, NPT,
2O3 mm long
½” TO 1½” Nipples, Carbon Steel to A 106 Gr. B, Sch. 80, Seamless, PBE, 76mm long
½” TO 1½” Nipples, Carbon Steel to A 106 Gr. B. Sch. 80, Seamless, Threaded one end, 76mm long.
½” TO 1½” Elbow, 90°, Carbon Steel to A 105, 3000#, Socket Weld, B16.11, (Note: 3)
½” TO 1½” Elbow, 45º, Carbon Steel to A 105, 3000#, Socket Weld, B16.11 (Note: 3)
½” TO 1½” Full Coupling, Carbon Steel to A 105 3000# Socket Weld, B16.11
½” TO 1½” Full Coupling, Carbon Steel to A 105, 3000# Screwed, NPT, B 16.11, (Note: 5)
½” TO 1½” Union (with integral seats) Carbon Steel to A 105, 3000 # , Socket Weld, B 16.11
½” TO 1½” union (with integral seats) Carbon Steel to A 105, 3000#, Screwed, NPT B16.11 (Note:5)
½” TO 1½” Half Coupling, Carbon Steel to A 105, 3000#, Socket Weld. B16.11
½” TO 1½” Half Coupling, Carbon Steel to A 105, 3000#, Screwed, NPT, B16.11 (Note: 5)
½” TO 1½” Equal Tee, Carbon Steel to A 105, 3000#, Socket Weld. B16.11
½” TO 1½” Reducing Tee, Carbon Steel to A105, 3000#, Socket Weld, B16.11
½” TO 1½” Caps, Carbon Steel to A105, 3000#, Screwed, NPT, B16.11, (Note: 5)
½” TO 1½” Hex. Headed Plug, Carbon Steel to A 105, 3000# Threaded, NPT
2” TO 6” Elbows 90º, Carbon Steel to A234 Gr. WPB, Sch. 40, Welded, Beveled end, B 16.9
2” TO 6” Elbows 45º, Carbon Steel to A 234 Gr. WPB, Sch. 40, Seamless, Beveled, B16.9
2” TO 1½” Equal Tee, Carbon Steel to A 234 Gr. WPB Sch. 40, Welded, Beveled end, B16.9
2” TO 1½” Reducer Tee, Carbon Steel to A 234 Gr. WPB, Sch.40, Welded, Beveled end, B16.9
SIZE RANGE DESCRIPTION
½” TO 2” Concentric Swage, Carbon Steel to A 106 Gr. B, Sch. 80, PBE, B 16.9
½” TO 2” Eccentric Swage Carbon Steel to A106 Gr. B, Sch. 80, PBE, B 16.9
2” TO 6” Concentric Reducer, Carbon Steel to A 234 Gr. WPB Sch.40, Seamless, Beveled end,
B 16.9
If small end Concentric Reducer, Carbon Steel to A 234 Gr. WPB, Sch.40, Beveled end, B16.9
2” TO 6”
2” TO 6” Eccentric Reducer, Carbon Steel to A 234 Gr. WPB, Sch. 40, Seamless, Beveled end,
B 16.9
If small end less Eccentric Reducer, use combination of reducer and swages
than 2”
If small end Eccentric Reducer, Carbon Steel to A234 Gr. WPB, Sch. 40, Beveled end, B 16.5
2” TO 6”
2” TO 6” Caps, Carbon Steel to A 234 Gr. WPB, Sch.40, Beveled end, B 16.9
8” TO 10” Caps, Carbon Steel to A 234 Gr. WPB, Sch. 20, Beveled end, B16.9
½” TO 10” Flange, Carbon Steel to IS 2062, Slip on raised face, Bore to suit Outside Diameter of pipe,
B 16.5, serrated finish 150#
½” TO 10” Flange, Carbon Steel to IS 2062, Slip on raised face, Bore to suit Outside Diameter of pipe,
B 16.5 serrated finish 300# (Note: 4)
½ “ TO 10” Blind Flange, Carbon Steel to IS 2062, 150# Raised face B16.5, serrated finish
½” TO 10” Gaskets, Compressed Asbestos Fibre, 1.6mm Thk., Ring type, graphited, BS 1832,
dimensions to B 16.21, 150#
½” TO 10” Studs, Alloy Steel to A 193 Gr. B 7 Stud bolts, A 194 Gr. 2H, Hex. Nuts
½” TO1½” Gate valve, Solid Wedge, Outside Stem & Yoke, Bolted Bonnet, Body Carbon Steel to
A 105, 13% Cr Trim, Socket Weld ends, 800#
½” TO 1½” Globe valve, Plug Disc, Outside Stem & Yoke, Bolted Bonnet, Body Carbon Steel to A105,
13% Cr Trim, Socket Weld ends, 800#
½” TO 1½” Ball Check Valve, BC, body Carbon Steel to A105, 13% Cr Trim, Socket Weld ends, 800#
(horizontal installation)
2” TO 10” Gate Valves, Solid Wedge, Outside Stem & Yoke, Bolted Bonnet, Body Carbon Steel to
A216 Gr. WCB, 13% Cr Trim, Flanged ends, 150# Raised Face, Serrated finish.
2” TO 6” Globe Valve, Loose Disc, Outside Stem & Yoke, Bolted Bonnet, Body Carbon Steel to
A 216 Gr. WCB, 13% Cr Trim, Flanged ends, 150# Raised Face, Serrated finish
2” TO 4” Check Valve. Swing Type, BC, Body Carbon Steel to A216 Gr. WCB, 13% Cr Trim, 150#
Raised Face, Flanged ends, Serrated finish
6” TO 10” Check valve, Wafer type, Single / Dual Plate, Stainless Steel Spring loaded, Body Carbon
Steel to A 216 Gr. WCB, 13% Cr Trim, 150# Raised Face, Suitable for installation between
150# Flanges, Raised face Serrated finish.
As per ID 8” TO 10” Strainer ‘T’ pattern as per Engg, Standard attached Annex.
As per ID 1½” TO 10” Strainer, Conical, Carbon Steel to A 285 Gr. C, 304 Stainless Steel mesh as
per Engg. Standard attached serrated finish.
As per ID I” TO 10” Figure‘8’ Line Blind, Carbon Steel to A 515 Gr. 70, Design & Dimensions as
per API 590 smooth Finish
TYPE OF JOINTS
NOTES
1. Flow orifices flanges to be supplied by instrument manufacturer.
2. Use socket weld x threaded end gate valves for instrument connections and drains.
3. 5-d bends shall be used for line size 1 ½ “and smaller.
4. Use 300# flanges at equipments and control valves, if required.
5. Screwed connections shall used for inst. Connections, vents & drains.
Branch piping, including integrally reinforced branch connection fittings, shall be attached to the header piping by means of full
penetration groove weld and shall be finished with a cover fillet weld of the size shown in the above chart
Reinforcing pads shall be attached to branch piping by means of a full penetration groove weld and shall be finished with a
cover fillet weld of the size shown in the above chart.
All threadolet branch connection fittings shall be 3000 lb. forged steel.
All branch connections shall be made in accordance with details contained in Std for field fabricated piping systems.