Professional Documents
Culture Documents
Page 1 of 7
Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 325 L EXCAVATOR 2SL00680
Configuration: 325, 325 L AND 325 LN EXCAVATORS 2SL00001-UP (MACHINE) POWERED BY 3116 ENGINE
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb... 23/12/2020
325, 325 L AND 325 LN EXCAVATORS 2SL00001-UP (MACHINE) POWERED BY ... Page 2 of 7
NOTE: At this point the accelerator and decelerator cables at the governor and the four clips on the
left side of the engine can be disconnected. Then the entire governor control motor assembly can be
removed.
NOTE: For installation of the governor control motor, reverse the removal steps.
NOTE: This disassembly and assembly procedure is shown only to show the disconnection of the
accelerator and decelerator at the governor control motor. Governor control motor assembly is now
serviced as a unit.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb... 23/12/2020
325, 325 L AND 325 LN EXCAVATORS 2SL00001-UP (MACHINE) POWERED BY ... Page 3 of 7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb... 23/12/2020
325, 325 L AND 325 LN EXCAVATORS 2SL00001-UP (MACHINE) POWERED BY ... Page 4 of 7
13. Carefully remove two screws (13) (not shown) from micro switches (14). There are two micro
switches.
14. Slide rubber boots from cables (15) to expose spring cable tighteners at end of springs. Remove
spacers at the end of the springs.
19. Disconnect cable ends (15) located in housing (21) from ring gear (20).
NOTE: The following steps are for the assembly of the governor control motor.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb... 23/12/2020
325, 325 L AND 325 LN EXCAVATORS 2SL00001-UP (MACHINE) POWERED BY ... Page 5 of 7
22. Lightly grease planet gears (17) and space equally in ring gear as shown.
25. Put screws (13) in both micro switches (14) and install electrical unit (16).
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb... 23/12/2020
325, 325 L AND 325 LN EXCAVATORS 2SL00001-UP (MACHINE) POWERED BY ... Page 6 of 7
33. Motor (5), carrier and planet gears (6), metal ring (7), and ring gear (8) shown before assembly.
34. Install ring gear (8). Mesh this gear with planet gears (17).
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb... 23/12/2020
325, 325 L AND 325 LN EXCAVATORS 2SL00001-UP (MACHINE) POWERED BY ... Page 7 of 7
37. Install motor (5). Mesh motor gear with planetary (6).
End By:
Copyright 1993 - 2020 Caterpillar Inc. Wed Dec 23 21:31:28 UTC+0300 2020
All Rights Reserved.
Private Network For SIS Licensees.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb... 23/12/2020