Professional Documents
Culture Documents
Infineon BTS410E2 DS v01 01 En-3161003
Infineon BTS410E2 DS v01 01 En-3161003
Product Summary
Overvoltage protection Vbb(AZ) 65 V
Operating voltage Vbb(on) 4.7 ... 42 V
Features On-state resistance RON 220 m
Overload protection
Current limitation Load current (ISO) IL(ISO) 1.8 A
Short circuit protection Current limitation IL(SCr) 5 A
Thermal shutdown
Overvoltage protection (including load dump)
Fast demagnetization of inductive loads PG-TO263-5-2
Reverse battery protection1)
Undervoltage and overvoltage shutdown with
auto-restart and hysteresis
Open drain diagnostic output
Open load detection in ON-state
CMOS compatible input
Loss of ground and loss of Vbb protection
Electrostatic discharge (ESD) protection
Green Product (RoHS compliant)
AEC Qualified
Application
C compatible power switch with diagnostic feedback for 12 V and 24 V DC grounded loads
All types of resistive, inductive and capacitve loads
Replaces electromechanical relays, fuses and discrete circuits
General Description
N channel vertical power FET with charge pump, ground referenced CMOS compatible input and diagnostic
feedback, monolithically integrated in Smart SIPMOS technology. Providing embedded protective functions.
+ V bb 3
Voltage Overvoltage Current Gate
source protection limit protection
V Logic
Limit for OUT
Voltage Charge pump
unclamped 5
sensor Level shifter ind. loads Temperature
Rectifier sensor
2 IN
Open load
Load
ESD Logic detection
4 ST
Short circuit
detection
GND PROFET
1
Signal GND Load GND
)
1
With external current limit (e.g. resistor RGND=150 ) in GND connection, resistors in series with IN and ST
connections, reverse load current limited by connected load.
Data Sheet 1 2013-10-15
BTS410E2
Thermal Characteristics
Parameter and Conditions Symbol Values Unit
min typ max
Thermal resistance chip - case: RthJC -- -- 2.5 K/W
junction - ambient (free air): RthJA -- -- 75
SMD version, device on PCB5): -- 35 --
2) Supply voltages higher than Vbb(AZ) require an external current limit for the GND and status pins, e.g. with a
150 resistor in the GND connection and a 15 k resistor in series with the status pin. A resistor for the
protection of the input is integrated.
3)
RI = internal resistance of the load dump test pulse generator
4)
VLoad dump is setup without the DUT connected to the generator per ISO 7637-1 and DIN 40839
5) Device on 50mm*50mm*1.5mm epoxy PCB FR4 with 6cm2 (one layer, 70m thick) copper area for Vbb
connection. PCB is vertical without blown air.
Data Sheet 2 2013-10-15
BTS410E2
Electrical Characteristics
Parameter and Conditions Symbol Values Unit
at Tj = 25 °C, Vbb = 12 V unless otherwise specified min typ max
Operating Parameters
Operating voltage 6) Tj =-40...+150°C: Vbb(on) 4.7 -- 42 V
Undervoltage shutdown Tj =25°C: Vbb(under) 2.9 -- 4.5 V
Tj =-40...+150°C: 2.7 -- 4.7
Undervoltage restart Tj =-40...+150°C: Vbb(u rst) -- -- 4.9 V
Undervoltage restart of charge pump Vbb(ucp) -- 5.6 6.0 V
see diagram page 13
Undervoltage hysteresis Vbb(under) -- 0.1 -- V
Vbb(under) = Vbb(u rst) - Vbb(under)
Overvoltage shutdown Tj =-40...+150°C: Vbb(over) 42 -- 52 V
Overvoltage restart Tj =-40...+150°C: Vbb(o rst) 40 -- -- V
Overvoltage hysteresis Tj =-40...+150°C: Vbb(over) -- 0.1 -- V
7)
Overvoltage protection Tj =-40...+150°C: Vbb(AZ) 65 70 -- V
Ibb=4 mA
Standby current (pin 3) Tj=-40...+25°C: Ibb(off) -- 10 15 A
VIN=0 Tj= 150°C: -- 18 25
Leakage output current (included in Ibb(off)) IL(off) -- -- 20 A
VIN=0
6) At supply voltage increase up to Vbb= 5.6 V typ without charge pump, VOUT Vbb - 2 V
7)
Meassured without load. See also VON(CL) in table of protection functions and circuit diagram page 7.
Data Sheet 3 2013-10-15
BTS410E2
Protection Functions9)
Initial peak short circuit current limit (pin 3 to 5)10), IL(SCp)
( max 450 s if VON > VON(SC) )
Tj =-40°C: 9 -- 23 A
Tj =25°C: -- 12 --
Tj =+150°C: 4 -- 15
Repetitive overload shutdown current limit IL(SCr)
VON= 8 V, Tj = Tjt (see timing diagrams, page 11) -- 5 -- A
Short circuit shutdown delay after input pos. slope
VON > VON(SC), Tj =-40..+150°C: td(SC) -- -- 450 s
min value valid only, if input "low" time exceeds 60 s
Output clamp (inductive load switch off)
at VOUT = Vbb - VON(CL) IL= 40 mA, Tj =-40..+150°C: VON(CL) 61 68 73 V
IL= 1 A, Tj =-40..+150°C: -- -- 75
Short circuit shutdown detection voltage
(pin 3 to 5) VON(SC) -- 8.5 -- V
Thermal overload trip temperature Tjt 150 -- -- °C
Thermal hysteresis Tjt -- 10 -- K
Reverse battery (pin 3 to 1) 11) -Vbb -- -- 32 V
Diagnostic Characteristics
Open load detection current IL (OL) mA
(on-condition) Tj=-40 ..150°C: 2 -- 150
)
8
Add IST, if IST > 0, add IIN, if VIN>5.5 V
)
9
Integrated protection functions are designed to prevent IC destruction under fault conditions described in the
data sheet. Fault conditions are considered as "outside" normal operating range. Protection functions are not
designed for continuous repetitive operation.
10)
Short circuit current limit for max. duration of td(SC) max=450 s, prior to shutdown
11)
Requires 150 resistor in GND connection. The reverse load current through the intrinsic drain-source
diode has to be limited by the connected load. Note that the power dissipation is higher compared to normal
operating conditions due to the voltage drop across the intrinsic drain-source diode. The temperature
protection is not active during reverse current operation! Input and Status currents have to be limited (see
max. ratings page 2 and circuit page 7).
Data Sheet 4 2013-10-15
BTS410E2
12)
If a ground resistor RGND is used, add the voltage drop across this resistor.
Data Sheet 5 2013-10-15
BTS410E2
Truth Table
Input- Output Status
level level 412 410 410 410 410
B2 D2 E2/F2 G2 H2
Normal L L H H H H H
operation H H H H H H H
13
Open load L ) L H H H L
H H H L L L H
Short circuit L L H H H H H
to GND H L L L L H L
Short circuit L H L H H H L
H (L )) H (L14)) H (L14))
14
to Vbb H H H H
Overtem- L L L L L L L
perature H L L L L L L
L15) L )
15
Under- L L H H H
voltage H L L15) L 15) H H H
Overvoltage L L L L H H H
H L L L H H H
L = "Low" Level X = don't care Z = high impedance, potential depends on external circuit
H = "High" Level Status signal after the time delay shown in the diagrams (see fig 5. page 12...13)
ESD-
ZDI1 ZDI2
I
I
GND
13) Power Transistor off, high impedance, versions BTS 410H, BTS 412B: internal pull up current source for
open load detection.
14)
Low resistance short Vbb to output may be detected in ON-state by the no-load-detection
15)
No current sink capability during undervoltage shutdown
Data Sheet 6 2013-10-15
BTS410E2
Short circuit detection
Fault Condition: VON > 8.5 V typ.; IN high
Open-load detection
ON-state diagnostic condition: VON < RON * IL(OL); IN
+ V bb high
+ V bb
V
ON
OUT
VON
Logic Short circuit ON
unit detection
OUT
V
Z
OUT
3
GND P R OFE T Vbb
IN
2
V
R IN
Z2
Any kind of load. In case of Input=high is VOUT VIN - VIN(T+) .
IN
Due to VGND >0, no VST = low signal available.
Logic
ST
GND disconnect with GND pull up
R ST
V
Z1 P R O FE T 3
GND Vbb
IN
R GND 2
PROFET OUT
Signal GND 5
ST
VZ1 = 6.2 V typ., VZ2 = 70 V typ., RGND= 150 , RIN, 4
GND
RST= 15 k 1
V V V
V IN ST GND
bb
Any kind of load. If VGND > VIN - VIN(T+) device stays off
Due to VGND >0, no VST = low signal available.
V
bb
high Vbb
IN
2
PROFET OUT
5 D
ST 10
4
GND
1
V
bb
E AS
ELoad
Vbb
IN
PROFET OUT
= ST EL
GND L
ZL { RL ER
D=
0.5
0.1 0.2
0.1
0.05
0.02
0.01
0
0.01
1E-5 1E-4 1E-3 1E-2 1E-1 1E0 1E1
tp [s]
) Latch except when Vbb -VOUT < VON(SC) after shutdown. In most cases VOUT = 0 V after shutdown (V
OUT
16
0 V only if forced externally). So the device remains latched unless Vbb < VON(SC) (see page 4). No latch
between turn on and td(SC).
17)
With latch function. Reseted by a) Input low, b) Undervoltage
18)
No auto restart after overvoltage in case of short circuit
19)
Low resistance short Vbb to output may be detected in ON-state by the no-load-detection
Data Sheet 10 2013-10-15
BTS410E2
Timing diagrams
Figure 2b: Switching an inductive load
IN IN
t
d(bb IN) t
V d(ST)
bb ST
*)
V
V OUT
OUT
IL
ST open drain
I L(OL)
t t
A
in case of too early VIN=high the device may not turn on (curve A) *) if the time constant of load is too large, open-load-status may
td(bb IN) approx. 150 s occur
Figure 2a: Switching a lamp, Figure 3a: Turn on into short circuit,
IN IN
ST ST
V V
OUT
OUT
td(SC)
I I
L
L
t t
IN
IN
IL ST
I L(SCp)
IL(SCr)
V
OUT
T
J
ST t
IN IN
t
ST d(ST)
ST
V
OUT
V OUT
I
L
IL open
**)
t
t
V on VON(CL)
IN
t t
d(ST OL1) d(ST OL2)
ST
off-state
on-state
off-state
V
bb(over)
V
OUT
V V
bb(u rst) bb(o rst)
V
normal open normal bb(u cp)
I
L
V
bb(under)
V bb
t
charge pump starts at Vbb(ucp) =5.6 V typ.
td(ST OL1) = tbd s typ., td(ST OL2) = tbd s typ
Figure 7a: Overvoltage:
IN
IN
V bb
V ON(CL) Vbb(over) V bb(o rst)
V
bb
V Vbb(u cp)
bb(under)
V
bb(u rst)
V
OUT
V OUT
ST
ST open drain
t
IN
Vbb
V bb(o rst)
I L
ST
Attention please!
The information herein is given to describe certain
components and shall not be considered as a guarantee of
characteristics.
Terms of delivery and rights to technical change reserved.
We hereby disclaim any and all warranties, including but not
limited to warranties of non-infringement, regarding circuits,
descriptions and charts stated herein.
Infineon Technologies is an approved CECC manufacturer.
Information
For further information on technology, delivery terms and
conditions and prices please contact your nearest Infineon
Technologies Office in Germany or our Infineon
Technologies Representatives worldwide (see address list).
Warnings
Due to technical requirements components may contain
dangerous substances. For information on the types in
question please contact your nearest Infineon Technologies
Office.
Infineon Technologies Components may only be used in life-
support devices or systems with the express written
approval of Infineon Technologies, if a failure of such
components can reasonably be expected to cause the
failure of that life-support device or system, or to affect the
safety or effectiveness of that device or system. Life support
devices or systems are intended to be implanted in the
human body, or to support and/or maintain and sustain
and/or protect human life. If they fail, it is reasonable to
assume that the health of the user or other persons may be
endangered.
Authorized Distributor
Infineon:
BTS410E2 E3062A