Professional Documents
Culture Documents
TABLE OF CONTENT
1. SCOPE 1
4. MATERIALS 1
5
2-5
5. PROCEDURE 2-4
6
6.MIXING OF PAINT 5
6
7.REPAIR OF PAINTING 5
6
8.INSPECTION AND TEST 5
6-7
9.REPORTING 6-7
5. Procedure
5.1 SUFACE PREPARATION & APPLYING
5.1.1 Surface preparation shall be applied by sand blasting shall be as specification in the above applicable
specification and standard and point manufacturing data profile of sand blasting to be 50-75 microns unless specified
otherwise by painting supplier.
5.1.2 Rust, oil, grease, dust, stain and other extraneous matter shall be removed from the surfaces to be painted.
In the event that no surface preparation isspecified for given area, it shall be understood that all oil, grease, dirt, loose paint,
and any other contaminants which are detrimental coating system shall be removed prior to painting application.
5.1.3 The surface preparation shall be performed in accordance with the surface preparation system as per table no.1.
Paint shall be applied only on surfaces
5.1.4 Surface defects revealed by the blast cleaning process, should be ground,filled or treated in the appropriate manner.
Note : Primer should be applied within 4-6 hours after blasting for near white (Sa 2.5) blast cleaner surface shall be
primed within 2 hours. If exceed the specified time sweep blasting shall be under taken. or depend
on manufacturer recommend.
Table 1 Surface Preparation to Paint Manufacturer‟s Requirements
SP10 Near white metal cleaning Very thorough blast cleaning. Mill scale,
Rust and foreign matters shell be
remove to extent that the only traces
remaining are slight stains in the form of
spots of stripes.
SP6 Commercial blast cleaning Thorough blast cleaning. Almost all mill
Scale, rust and foreign matters shell be
Removed.
SP3 Power tool cleaning Removing rust, loose mill scale and
loose paint by using hand tools sand,
grind, chip or others.
SP2 Hand tool cleaning Removing loose rust, loose mill scale
and loose paint by using hand tools to
sand, scrape, brush, chip or otherwise.
3
7. REPAIR OF PAINTING
7.1 Painting damaged by handling, welding, oxy cutting or by other mean shall be repaired. surface preparation
as table1 Surface Preparation to Paint Manufacturer‟s Requirements SP3 power tool cleaning
and re‐coat as for new paint .
7.2 The repair of the damaged portion shall be performed by using the same paint as originally used.
7.3 The demand area surface preparation shall be done by using power wire brushing in lien of blasting remove
contamination and irregularity.
7.4 The previously applied paint shall be feathered back 50 mm. per coat to allow the correct application and
built up the required report.
9. REPORTING
Painting report shall be recorded in form which form shall be attached
- Form : Painting Inspection Record. ( FM-PP-020 ) Or Vendor’s from
PAINTING INSPECTION
REPORT
PROJECT No. : REPORT No. :
PROJECT TITLE : DATE :
CLIENT : Page :
TOTAL
ABB WTL SCOT
NAME _________________________ NAME _________________________ NAME ______________________________
SIGN. _________________________ SIGN. _________________________ SIGN. ______________________________
DATE _________________________ DATE _________________________ DATE ______________________________
FM-PP-020
Pate 8 of 60 9
PAINTING PROCEDURE
Steel Service and Construction
for The Shell Company of Thailand : SCOT Phoenix Project
Painting System LC1-N : Un-Insulated Carbon Steel, Serviced temp. (-35)o C < Temp. < 120o C
MKT-F-04-1-01/06/60
Pate 9 of 60 10
8
No.TH 6250
Jan' 20
GALBON S-HB
GALBON S-HB, is an inorganic zinc coating based on ethyl silicate and zinc dust type II per ASTM D-520.
It has zinc content by weight in dry film 86% comform to SSPC Paint No.20 Level 1 and ISO 12944-5. It gives
protection against corrosion prolonged weather resistance, good abrasion.
It also has continuous dry heat resistance up to 400°C and peak at 540°C for 1 hour.
TECHNICAL DATA
Type : Inorganic zinc silicate , high-build type
Recommended Use : As a protective coating outside of tank , pipe, steel structure, etc.
Mixing Ratio : Base : Zinc dust = 30 : 70 (by weight)
Colour : Grey
Flash Point : Base 14.5°C
VOC : 491 [g/litre] EPA method-24
Solid by Volume : 60.0 ± 2%
Coverage (Theoretical) : 0.08 - 0.14 l/m2 ; 12.0 - 7.06 m2/l
Wet Film Thickness : 3.33 - 5.67 mils ; 83 - 142 microns
Dry Film Thickness : 2.00 - 3.40 mils ; 50 - 85 microns
Drying Time : Temperature 10°C 20°C 30°C 40°C
(at D.F.T. 75 microns) : Surface Dry 30 mins. 20 mins. 10 mins. 5 mins.
: Hard Dry 5 hrs. 4 hrs. 3 hrs. 2 hrs.
Painting Interval : Minimum 32 hrs. 20 hrs. 14 hrs. 6 hrs.
(at D.F.T. 75 microns) : Maximum 180 days 180 days 180 days 180 days
Pot Life : 10 hrs. 7 hrs. 5 hrs. 3 hrs.
Thinner : CMP-61
Method of Application : Airless spray, Brush is recommended for small touch up area.
Conditions of Application : Temperature 5 - 50°C
Humidity 50 - 95 % RH
For Airless spray
Tip No. GRACO 419 , 519
Paint output pressure 9.8 MPa.
Viscosity 10-12 sec (Ford Cup No.4)
Thinning 0 - 5% by volume
Surface preparation : Surfaces must be clean and dry ,remove dirt, dust, oil and all other
contaminants that could interfere with adhesion of the next coat.
Steel : Recommend Blast cleaning to Sa 2½ (ISO 8501-1)
Anchor profile 30-65 µm are recommended for the highest performance.
Preceding Coats : Cerabond 2000
Subsequent Coats : Epicon series, Umeguard series , Silicon series, etc
Packaging : Two pack product : 3.8 Litres / Gallon
Shelf life at 25°C : Base 6 months , Zinc dust 12 months , In unopened container
Note ; 1.Dry film thickness in excess of 5.0 mils (125 microns) is not recommended
2.Before apply the next coat the paint film of GALBON S-HB must dry clean and free of zinc salts, etc.
3. Mist coat is required to minimize topcoat bubbling, thinning 30-40% is recommended.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
11
2. HARZARDS IDENTIFICATION
GHS CLASSIFICATION Category Hazard statement Hazard
Flammable liquids 2 Highly Flammable liquid and vapour
Acute Toxicity [skin , Dermal] 4 Harmful in contact with skin
Acute Toxicity [inhalation] 4 Harmful if inhaled
Acute Toxicity [ingestion , Oral] 4 Harmful if swallowed
Skin corrosion / irritation 3 Causes mild skin irritation
Serious eye damage / eye irritation 2A Causes serious eye irritation
Specific target organ toxicity (single exposure) 3 May cause respiratory irritation drowsiness or dizziness
Specific target organ toxicity (repeated exposure) 2 Respiratory, Liver , Kidney , Central Nervous system)
Aspiration toxicity 1 May be fatal if swallowed and enters airways
Acute hazards to the aquatic environment 3 Harmful to aquatic life
Long-term hazards to the aquatic 3 Harmful to aquatic life with long lasting effects
GHS LABEL ELEMENTS
Pictograms
PRECAUTIONARY STATEMENTS
Page 1 / 8
12
PREVENTION
P210 : Keep away from heat/sparks/open flames/hot surfaces. - No smoking.
P233 : Keep container tightly closed.
P260 : Do not breathe dust/fume/gas/mist/vapours/spray.
P264 : Wash hand thoroughly after handling.
P272 : Contaminated work clothing should not be allowed out of the workplace.
P273 : Avoid release to the environment.
P280 : Wear protective gloves/protective clothing/eye protection/face protection.
STORAGE
P403 + P233 : Store in a well-ventilated place. Keep container tightly closed.
DISPOSAL
P501 : Dispose of contents and container to appropriate waste site or reclaimer in accordance with local and national regulations.
4. FIRST-AID MEASURES
4.1 Description of first-aid measures
General
: In all cases of doubt, or when symtoms persist, seek medical attention. Never give anything by mouth
to an unconscious person. If unconcious place in recovery position and seek medical advice.
Eye contact
: Check for and remove any contact lenses. Immediately flush eyes with running clean fresh
water for at least 15 minutes, keeping the eyelids open and seek medical attention.
Skin contact
: Remove contaminated clothing and shoes. Wash skin throughly with soap and water or use
recognised skin cleanser. Do not use solvents or thinners.
Inhalation
: Remove to fresh air. Keep patient warm and at rest. If not breathing, if breathing is irregular
or if respiratory arrest occures, provide artificial respiration or oxygen by trained personnel.
Ingestion
: If accidentally swallow obtain immediate medical attention and show the container or label.
Page 2 / 8
13
Page 3 / 8
13
14
Page 4 / 8
15
14
Page 5 / 8
16
Carcinogenicity:
Conclusion/Summary on mixture : No specific data.
Reproductive toxicity:
Conclusion/Summary on mixture : No specific data.
Aspiration hazard:
Conclusion/Summary on mixture : No specific data.
Potential acute health effects
Inhalation : Exposure to vapours may cause a health hazard.
Page 6 / 8
17
Page 7 / 8
18
19
Paint and waste should be disposed in small pieces by the open type of incinerator to have absorbed them with diatomite.
Containers which are not properly cleaned may contain (highly) flammable or explosive vapours.
Special precautions:
Use appropriate protective equipment for the removal and / or disposal of this product
Packing group II II II
Environmental hazard No Yes No
Marine pollutant - Yes -
It is always the responsibility of the user to take all necessary steps to meet the demands of applicable legislation.
The information contained in this safety data sheet does not constitute the user’s own assessment of workplace risks, as
required by other health and safety legislation
Page 8 / 8
19
No.TH 5422H
Jan' 20
EPICON F-HS
EPICON F-HS, based on a combination of epoxy resin, polyamide curing agent and micaceous iron oxide.
It has excellent weather resistance and physical properties such as hardness, abrasion resistance.
It has excellent compatibility with almost type of the subsequent coat and excellent resistance to oil,
seawater, freshwater and chemicals such as weak acid or weak alkali.
TECHNICAL DATA
Type : High-solid Low VOC and epoxy polyamide with micaceous iron oxide
Recommended Use : As a heavy duty coat for bridge, plants, external tank, steel structures, etc.
Mixing Ratio : Base : Hardener = 70 : 30 (by volume) ; 85 : 15 (by weight)
Colour : Light Grey , Dark Grey
Flash Point : Base = 23°C Hardener = 27°C
VOC : 230 [g/litre] EPA method-24
Solid by Volume : 85.0 ± 2%
Coverage (Theoretical) : 0.06 - 0.18 l/m2 ; 17.0 - 5.67 m2/l
Wet Film Thickness : 2.35 - 7.06 mils ; 59 - 176 microns
Dry Film Thickness : 2.00 - 6.00 mils ; 50 - 150 microns
Drying Time : Temperature 10°C 20°C 30°C 40°C
(at D.F.T. 100 microns) : Surface Dry 3.5 hrs. 2.5 hrs. 1.5 hrs. 1 hr.
: Hard Dry 20 hrs. 16 hrs. 14 hrs. 12 hrs.
Painting Interval : Minimum 18 hrs. 12 hrs. 8 hrs. 6 hrs.
(at D.F.T. 100 microns) : Maximum - - - -
Pot Life : 20 hrs. 15 hrs. 12 hrs. 10 hrs.
Thinner : CMP-31
Method of Application : Airless spray , Roller , Brush
Conditions of Application : Temperature Minimum 10°C
Humidity Maximum 85% RH
For Airless spray :
Tip No. GRACO 415 , 417
Paint output pressure 14.7 - 17.7 MPa.
Viscosity 1.5 - 2.0 Pa.s
Thinning 0 - 15% by volume
Preceding coats : Zinc Rich Primer coating such as , Epicon Zinc HB-2 , Galbon S-HB , etc.
Subsequent coats : Wide range of any coating such as , Epoxy , Polyurethane , etc.
Packaging : Two pack product : 3.785 Litres / Gallon , 15.14 Litres / Drum
Shelf life at 25°C : Base 24 months , Hardener 24 months , In unopened container
Note ; As nature of Epoxy coating EPICON F-HS can not avoid chalking and fading on UV exposure.
Before the next coat is applied the surface must clean and dry, remove dirt, dust, oil and all other contaminants.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
20
2. HARZARDS IDENTIFICATION
GHS CLASSIFICATION Category Hazard statement Hazard
Flammable liquids 3 Flammable liquid and vapour
Acute Toxicity [skin , Dermal] 4 Harmful in contact with skin
Acute Toxicity [inhalation] 4 Harmful if inhaled
Acute Toxicity [ingestion , Oral] 4 Harmful if swallowed
Skin corrosion / irritation 2 Causes skin irritation
Serious eye damage / eye irritation 2A Causes serious eye irritation
Specific target organ toxicity (single exposure) 3 May cause respiratory irritation drowsiness or dizziness
Specific target organ toxicity (repeated exposure) 2 Respiratory, Liver , Kidney , Central nervous system)
Aspiration toxicity 1 May be fatal if swallowed and enters airways
Acute hazards to the aquatic environment 3 Harmful to aquatic life
Long-term hazards to the aquatic 3 Harmful to aquatic life with long lasting effects
GHS LABEL ELEMENTS
Pictograms
Page 1 / 8
21
25
24
23
STORAGE
P403 + P233 : Store in a well-ventilated place. Keep container tightly closed.
DISPOSAL
P501 : Dispose of contents and container to appropriate waste site or reclaimer in accordance with local and national regulations.
4. FIRST-AID MEASURES
4.1 Description of first-aid measures
General
: In all cases of doubt, or when symtoms persist, seek medical attention. Never give anything by mouth
to an unconscious person. If unconcious place in recovery position and seek medical advice.
Eye contact
: Check for and remove any contact lenses. Immediately flush eyes with running clean fresh
water for at least 15 minutes, keeping the eyelids open and seek medical attention.
Skin contact
: Remove contaminated clothing and shoes. Wash skin throughly with soap and water or use
recognised skin cleanser. Do not use solvents or thinners.
Inhalation
: Remove to fresh air. Keep patient warm and at rest. If not breathing, if breathing is irregular
or if respiratory arrest occures, provide artificial respiration or oxygen by trained personnel.
Ingestion
: If accidentally swallow obtain immediate medical attention and show the container or label.
Keep patient warm and at rest. Do not induce vomitting.
4.2. Most important symptoms and effects, both acute and delayed
Potential acute symptoms and effects
Page 2 / 8
22
Inhalation
Exposure to vapors may cause a health hazard.
Serious effects may be delayed following exposure
Skin contact
Irritating to skin. May cause sensitisation by skin contact.
Eye contact
Irritating to eyes.
Ingestion
Harmful if swallowed
Potential delayed symptoms and effects
Inhalation
No specific data
Skin contact
Adverse symptoms may include the following: irritation, redness
Eye contact
Adverse symptoms may include the following: irritation, watering, redness
Ingestion
No specific data
4.3. Indication of any immediate medical attention and special treatment needed
Notes to physician
In case of inhalation of decomposition products in a fire, symptoms may be delayed
The exposed person may need to be kept under medical surveillance for 48 hours
Specific treatments
No specific treatment
Page 3 / 8
23
28
Page 4 / 8
24
Page 5 / 8
25
31
Skin corrosion/irritation:
Conclusion/Summary on mixture : Causes skin irritation.
: Method: Additivity approach, no testdata available.
Serious eye damage/irritation:
Conclusion/Summary on mixture : No specific data.
Carcinogenicity:
Conclusion/Summary on mixture : No specific data.
Reproductive toxicity:
Conclusion/Summary on mixture : No specific data.
Aspiration hazard:
Conclusion/Summary on mixture : No specific data.
Page 6 / 8
33
26
Page 7 / 8
27
35
Use appropriate protective equipment for the removal and / or disposal of this product
It is always the responsibility of the user to take all necessary steps to meet the demands of applicable legislation.
The information contained in this safety data sheet does not constitute the user’s own assessment of workplace risks, as
required by other health and safety legislation
Page 8 / 8
28
No.TH 5512
Jan' 20
UNY MARINE HS
UNY MARINE HS, based on acrylic polyol and non-yellowing polyisocyanates resin , has excellent
gloss retention, durability and chemical resistance, etc . It is suitable for protection of tank , tower, bridge
and other steel structures.
TECHNICAL DATA
Type : Acrylic aliphatic polyurethane paint (non yellowing), high solid
Recommended Use : Finish coat of Epoxy system for bridge, chemical plant oil tank
and steel structures, etc.
Mixing Ratio : Base : Hardener = 80 : 20 (by volume) , 5 : 1 (by weight)
Colour : White , as specified
Flash Point : Base = 23.5°C Hardener = 29°C
VOC : 430 [g/litre] EPA method-24
Solid by Volume : 61.0 ± 2%
Coverage (Theoretical) : 0.07 - 0.12 l/m2 ; 15.3 - 8.1 m2/l
Wet Film Thickness : 2.62 - 4.92 mils ; 66 - 123 microns
Dry Film Thickness : 1.60 - 3.00 mils ; 40 - 75 microns
Drying Time : Temperature 10°C 20°C 30°C 40°C
(at D.F.T. 40 microns) : Surface Dry 2 hrs. 1 hr. 30 mins. 15 mins.
: Hard Dry 14 hrs. 8 hrs. 7 hrs. 4 hrs.
Painting Interval : Minimum 6 hrs. 4 hrs. 2 hrs. 1 hr.
(at D.F.T. 40 microns) : Maximum - - - -
Pot Life : 8 hrs. 7 hrs. 6 hrs. 4 hrs.
Thinner : CMP-41
Method of Application : Airless spray , Roller , Brush
Conditions of Application : Temperature Minimum 5°C
Humidity Maximum 85% RH
For Airless spray :
Tip No. GRACO 715 , 813
Paint output pressure 12 - 15 MPa.
Viscosity 25 - 35 sec (Ford Cup No.4)
Thinning 0 - 15 % by volume
Preceding coats : Epicon HB-CL, Epicon HB-NP, Epicon Undercoat , Epicon F-HS ,
Umeguard HS , Umeguard HS Silver, Univan HS , etc.
Subsequent coats : -
Packaging : Two pack product per set ; 3.785 Litres / Gallon , 18.925 Litres / Drum
Shelf life at 25°C : Base 24 months , Hardener 24 months , In unopened container
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
29
2. HARZARDS IDENTIFICATION
GHS CLASSIFICATION OF MIXTURE Category Hazard statement Hazard
Flammable liquids 3 Flammable liquid and vapour
Acute Toxicity [skin , Dermal] 4 Harmful in contact with skin
Acute Toxicity [inhalation] 4 Harmful if inhaled
Acute Toxicity [ingestion , Oral] 4 Harmful if swallowed
Skin corrosion / irritation 2 Causes skin irritation
Serious eye damage / eye irritation 2A Causes serious eye irritation
Respiratory sensitizer NC.
Skin sensitizer NC.
Germ cell mutagenicity NC.
Carcinogenicity NC.
Reproductive Toxicity NC.
Effects on or via lactation NC.
Specific target organ toxicity (single exposure) 1 (Respiratory, liver, central nervous system,kidney)
Specific target organ toxicity (repeated exposure) 1 (Respiratory, nervous system)
Aspiration toxicity 1 May be fatal if swallowed and enters airways
Acute hazards to the aquatic environment 2 Toxic to aquatic life
Long-term hazards to the aquatic 2 Toxic to aquatic life with long lasting effects
Hazard to the Ozone Layer NC.
GHS LABEL ELEMENTS
Pictograms
Page 1 / 8
30
PRECAUTIONARY STATEMENTS
PREVENTION
P210 : Keep away from heat/sparks/open flames/hot surfaces. - No smoking.
P233 : Keep container tightly closed.
P260 : Do not breathe dust/fume/gas/mist/vapours/spray.
P264 : Wash hand thoroughly after handling.
P272 : Contaminated work clothing should not be allowed out of the workplace.
P273 : Avoid release to the environment.
P280 : Wear protective gloves/protective clothing/eye protection/face protection.
STORAGE
P403 + P233 : Store in a well-ventilated place. Keep container tightly closed.
DISPOSAL
P501 : Dispose of contents and container to appropriate waste site or reclaimer in accordance with local and national regulations.
4. FIRST-AID MEASURES
4.1 Description of first-aid measures
General
: In all cases of doubt, or when symtoms persist, seek medical attention. Never give anything by mouth
to an unconscious person. If unconcious place in recovery position and seek medical advice.
Eye contact
: Check for and remove any contact lenses. Immediately flush eyes with running clean fresh
water for at least 15 minutes, keeping the eyelids open and seek medical attention.
Skin contact
: Remove contaminated clothing and shoes. Wash skin throughly with soap and water or use
recognised skin cleanser. Do not use solvents or thinners.
Inhalation
: Remove to fresh air. Keep patient warm and at rest. If not breathing, if breathing is irregular
Page 2 / 8
31
40
Page 3 / 8
32
Page 4 / 8
33
43
Carcinogenicity:
Conclusion/Summary on mixture : No specific data.
Reproductive toxicity:
Conclusion/Summary on mixture : No specific data.
Page 6 / 8
35
46
45
Page 7 / 8
36
It is always the responsibility of the user to take all necessary steps to meet the demands of applicable legislation.
The information contained in this safety data sheet does not constitute the user’s own assessment of workplace risks, as
required by other health and safety legislation
Page 8 / 8
37
PAINTING PROCEDURE
Steel Service and Construction
for The Shell Company of Thailand : SCOT Phoenix Project
Painting System LC10-N/M : Insulated Carbon Steel, Serviced temp. 50o C < Temp. < 175o C
MKT-F-04-1-01/06/60
38
No.TH 6037C
Jan' 20
EPICON T-800 HS-GF
EPICON T-800 HS-GF is a high-build type epoxy phenolic glassflake coating.
It is suitable as a protective coating for piping and tank. It has the following adventages;
1. Excellent temperature resistance up to 230 °C
2. Excellent physical properties such as adhesion, toughness, abrasion resistance and
wet/dry cycling condition resistance.
3. Excellent thermal shock resistance.
TECHNICAL DATA
Type : Epoxy phenolic glassflake coating, high-build
Recommended Use : Tank outside, insulated pipe, other steel structures, etc.
Mixing Ratio : Base : Hardener = 86 : 14 (by volume) , 90 : 10 (by weight)
Colour : Grey , Light Grey , Reddish Brown
Flash Point : Base = 27°C Hardener = 33°C
VOC : 361 [g/litre] EPA method-24
Solid by Volume : 75.0 ± 2%
Coverage (Theoretical) : 0.13 - 0.20 l/m2 ; 7.50 - 5.00 m2/l
Wet Film Thickness : 5.33 - 8.00 mils ; 133 - 200 microns
Dry Film Thickness : 4.00 - 6.00 mils ; 100 - 150 microns
Drying Time : Temperature 10°C 20°C 30°C 40°C
(at D.F.T. 150 microns) : Surface Dry 2.5 hrs. 1.5 hrs. 30 mins. 15 mins.
: Hard Dry 24 hrs. 12 hrs. 8 hrs. 6 hrs.
Painting Interval : Minimum 24 hrs. 16 hrs. 14 hrs. 8 hrs.
(at D.F.T. 150 microns) : Maximum 30 days. 30 days. 30 days. 30 days.
Pot Life : 7 hrs. 5 hrs. 3 hrs. 1.5 hrs.
Thinner : CMP-31
Method of Application : Airless spray , Roller , Brush
Conditions of Application : Temperature Minimum 5°C
Humidity Maximum 85% RH
For Airless spray :
Tip No. GRACO 631 , 635
Paint output pressure 14.7 - 17.7 MPa.
Viscosity 1.0 - 1.5 Pa.s
Thinning 0 - 15 % by volume
Recommended Surface- : Steel : Blast cleaning to Sa 2½ (ISO 8501-1)
preparation Anchor profile 60-90 µm are recommended for the highest performance.
Preceding coats : -
Subsequent coats : Epicon T-800 HS-GF , etc.
Packaging : Two pack product per set ; 3.785 Litres / Gallon , 18.925 Litres / Drum
Shelf life at 25°C : Base 24 months , Hardener 24 months , In unopened container
Note ; 1.Even if discoloration occures under the sunshine , this is not an indication of a change in film resistance to the cargo.
2.In confined spaces such as tank insides ventilation is required during application and curing to removed solvent vapour
and promote curing.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
39
2. HARZARDS IDENTIFICATION
GHS CLASSIFICATION Category Hazard statement Hazard
Flammable liquids 3 Flammable liquid and vapour
Acute Toxicity [skin , Dermal] 4 Harmful in contact with skin
Acute Toxicity [inhalation] 4 Harmful if inhaled
Acute Toxicity [ingestion , Oral] 4 Harmful if swallowed
Skin corrosion / irritation 2 Causes skin irritation
Serious eye damage / eye irritation 1 Causes serious eye damage
Respiratory sensitizer NC.
Skin sensitizer NC.
Germ cell mutagenicity NC.
Carcinogenicity NC.
Reproductive Toxicity NC.
Effects on or via lactation NC.
Specific target organ toxicity (single exposure) 1 (Respiratory, liver, central nervous system,kidney)
Specific target organ toxicity (repeated exposure) 1 (Respiratory, nervous system)
Aspiration toxicity 1 May be fatal if swallowed and enters airways
Acute hazards to the aquatic environment 2 Toxic to aquatic life
Long-term hazards to the aquatic 2 Toxic to aquatic life with long lasting effects
Hazard to the Ozone Layer NC.
GHS LABEL ELEMENTS
Pictograms
Page 1 / 8
40
53
52
PRECAUTIONARY STATEMENTS
PREVENTION
P210 : Keep away from heat/sparks/open flames/hot surfaces. - No smoking.
P233 : Keep container tightly closed.
P260 : Do not breathe dust/fume/gas/mist/vapours/spray.
P264 : Wash hand thoroughly after handling.
P272 : Contaminated work clothing should not be allowed out of the workplace.
P273 : Avoid release to the environment.
P280 : Wear protective gloves/protective clothing/eye protection/face protection.
STORAGE
P403 + P233 : Store in a well-ventilated place. Keep container tightly closed.
DISPOSAL
P501 : Dispose of contents and container to appropriate waste site or reclaimer in accordance with local and national regulations.
4. FIRST-AID MEASURES
4.1 Description of first-aid measures
General
: In all cases of doubt, or when symtoms persist, seek medical attention. Never give anything by mouth
to an unconscious person. If unconcious place in recovery position and seek medical advice.
Eye contact
: Check for and remove any contact lenses. Immediately flush eyes with running clean fresh
water for at least 15 minutes, keeping the eyelids open and seek medical attention.
Skin contact
: Remove contaminated clothing and shoes. Wash skin throughly with soap and water or use
recognised skin cleanser. Do not use solvents or thinners.
Page 2 / 8
41
Inhalation
: Remove to fresh air. Keep patient warm and at rest. If not breathing, if breathing is irregular
or if respiratory arrest occures, provide artificial respiration or oxygen by trained personnel.
Ingestion
: If accidentally swallow obtain immediate medical attention and show the container or label.
Keep patient warm and at rest. Do not induce vomitting.
4.2. Most important symptoms and effects, both acute and delayed
Potential acute symptoms and effects
Inhalation
Exposure to vapors may cause a health hazard.
Serious effects may be delayed following exposure
Skin contact
Irritating to skin. May cause sensitisation by skin contact.
Eye contact
Irritating to eyes.
Ingestion
Harmful if swallowed
Potential delayed symptoms and effects
Inhalation
No specific data
Skin contact
Adverse symptoms may include the following: irritation, redness
Eye contact
Adverse symptoms may include the following: irritation, watering, redness
Ingestion
No specific data
4.3. Indication of any immediate medical attention and special treatment needed
Notes to physician
In case of inhalation of decomposition products in a fire, symptoms may be delayed
The exposed person may need to be kept under medical surveillance for 48 hours
Specific treatments
No specific treatment
Page 3 / 8
42
56
Page 4 / 8
43
58
Engineering measures
: Provide adequate ventilation. Where resonably practicable, this should be achived by the use of local exhaust
ventilation and good general extraction. If these are not sufficient to maintain concentrations of particulates
and solvent vapours below the occupational exposure limits (OEL) suitable respirator must be worn.
Page 5 / 8
44
60
Skin corrosion/irritation:
Conclusion/Summary on mixture : Causes skin irritation.
: Method: Additivity approach, no testdata available.
Serious eye damage/irritation:
Conclusion/Summary on mixture : Causes serious eye damage.
: Method: Additivity approach, no testdata available.
Respiratory or skin sensitization:
Conclusion/Summary on mixture : May cause an allergic skin reaction.
: Method: Concentration Limit, no testdata available.
: No specific data on Respiratory sensitization.
: Method: Concentration Limit, no testdata available
Germ cell mutagenicity:
Conclusion/Summary on mixture : No specific data.
Carcinogenicity:
Conclusion/Summary on mixture : No specific data.
Reproductive toxicity:
Page 6 / 8
45
Aspiration hazard:
Conclusion/Summary on mixture : No specific data.
Page 7 / 8
46
Silica Cristaline EC50 - Not available, LC50 - Not available, IC50 - Not available
Epoxy Resin Mwt 700-1100 EC50/48h >100 mg/l (Daphnia magna), LC50/96h >100 mg/l (Leuciscus idus), IC50 - Not available
It is always the responsibility of the user to take all necessary steps to meet the demands of applicable legislation.
The information contained in this safety data sheet does not constitute the user’s own assessment of workplace risks, as
required by other health and safety legislation
Page 8 / 8
47
63
PAINTING PROCEDURE
Steel Service and Construction
for The Shell Company of Thailand : SCOT Phoenix Project
Painting System LC11-N/M : Insulated Carbon Steel, Serviced temp. 175o C < Temp. < 595o C
MKT-F-04-1-01/06/60
48
No.TH 8009B
Jan' 20
SILBON HB-CUI
SILBON HB-CUI is based on Inorganic copolymer and metallic flake.
It is designed to provide anti-corrosion under insulation for pipe coating which is exposed to continuous
operating temperature -196°C to 650°C . It has the advantages as follow;
1. Excellent adhesion on steel and stainless steel.
2. Excellent anti-corrosion under insulation.
3. Film drying at ambient temperature.
4. Resistance to thermal shock and thermal cycling in service.
5. Prevent stress corrosion cracking.
TECHNICAL DATA
Type : High build Inorganic copolymer heat resistance
Recommended Use : Structure , Pipe , Corrosion under insulation
Mixing Ratio : Base : Accelerator = 100 : 1.8 (by weight)
Colour : Aluminium
Flash Point: Base 25°C Accelerator 90°C
VOC : 339 [g/litre] EPA Method 24
Solid by Volume : 75.0 ± 2%
Coverage (Theoretical) : 0.13 - 0.20 l/m2 ; 7.50 - 5.00 m2/l
Wet Film Thickness : 5.33 - 8.00 mils ; 133 - 200 microns
Dry Film Thickness : 4.00 - 6.00 mils ; 100 - 150 microns
Drying Time : Temperature 10°C 20°C 30°C 40°C
(at D.F.T. 125 microns) : Surface Dry 4 hrs. 3 hrs. 2 hrs. 1 hr.
: Hard Dry 12 hrs. 8 hrs. 6 hrs. 5 hrs.
Painting Interval : Minimum 12 hrs. 8 hrs. 6 hrs. 5 hrs.
(at D.F.T. 125 microns) : Maximum
Pot Life : 12 hrs. 8 hrs. 5 hrs. 3 hrs.
Thinner : Silbon Thinner
Method of Application : Airless spray is recommended. Brush is used only for small area or touch up.
Roller is not recommended for high dry film thickness.
Conditions of Application : Temperature Minimum 10°C
Humidity Maximum 85 % RH
For Airless spray :
Tip No. GRACO 417 , 419 , 421
Paint output pressure 11.7 - 14.7 MPa.
Thinning 5 - 15 % by volume
Recommended Surface- : Steel : Blast cleaning to SSPC-SP 10 , Sa 2½ (ISO 8501-1)
preparation Duplex stainless : Blast cleaning to SSPC-SP16
Anchor profile 30-65 µm are recommended for the highest performance.
Preceding coats : Galbon S-HB , Galbon S-HB PZ-L1 or direct to steel.
Subsequent coats : Silbon HB-CUI
Packaging : Two pack product per set ; 3.785 Litres / Gallon
Shelf life at 25°C : Base 12 months , Accelerator 12 months , In unopened container
Notes ; Surface preparation ; All surface to be coated should be clean, dry and free from contamination.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
49
66
2. HARZARDS IDENTIFICATION
GHS CLASSIFICATION Category Hazard statement Hazard
Flammable liquids 3 Flammable liquid and vapour
Skin corrosion / irritation 2 Causes skin irritation
Serious eye damage / eye irritation 2A Causes serious eye irritation
Specific target organ toxicity (single exposure) 3 (Respiratory tract irritation)
Specific target organ toxicity (repeated exposure) 2 (Respiratory, nervous system)
Acute hazards to the aquatic environment 2 Toxic to aquatic life
GHS LABEL ELEMENTS
Pictograms
Page 1 / 8
50
68
4. FIRST-AID MEASURES
4.1 Description of first-aid measures
General
: In all cases of doubt, or when symtoms persist, seek medical attention. Never give anything by mouth
to an unconscious person. If unconcious place in recovery position and seek medical advice.
Eye contact
: Check for and remove any contact lenses. Immediately flush eyes with running clean fresh
water for at least 15 minutes, keeping the eyelids open and seek medical attention.
Skin contact
: Remove contaminated clothing and shoes. Wash skin throughly with soap and water or use
recognised skin cleanser. Do not use solvents or thinners.
Inhalation
: Remove to fresh air. Keep patient warm and at rest. If not breathing, if breathing is irregular
or if respiratory arrest occures, provide artificial respiration or oxygen by trained personnel.
Ingestion
: If accidentally swallow obtain immediate medical attention and show the container or label.
Keep patient warm and at rest. Do not induce vomitting.
4.2. Most important symptoms and effects, both acute and delayed
Potential acute symptoms and effects
Inhalation
Exposure to vapors may cause a health hazard.
Serious effects may be delayed following exposure
Skin contact
Irritating to skin. May cause sensitisation by skin contact.
Eye contact
Irritating to eyes.
Ingestion
Harmful if swallowed
Potential delayed symptoms and effects
Inhalation
No specific data
Skin contact
Adverse symptoms may include the following: irritation, redness
Eye contact
Adverse symptoms may include the following: irritation, watering, redness
Ingestion
Page 2 / 8
51
No specific data
4.3. Indication of any immediate medical attention and special treatment needed
Notes to physician
In case of inhalation of decomposition products in a fire, symptoms may be delayed
The exposed person may need to be kept under medical surveillance for 48 hours
Specific treatments
No specific treatment
Page 4 / 8
53
For prolonged or repeated handling, use the following type of gloves: gloves; nitrile.
Barrier creams may help to protect the exposed areas of the skin but should not be applied
once exposure has occurred.
For right choice of glove materials, with focus on chemical resistance and time of penetration,
seek advice by the supplier of chemical resistant gloves.
Skin Protection
: Overalls which cover the body, arms and legs should worn. Skinshould not be exposed.
Barrier creams may help to protect areas which are difficult to cover such as face and neck.
They should howerve not be applied once ecposure has occurred. Petroleum jelly based types
Such as vaseline should not be used. All part of the body should be washed after contact.
Skin corrosion/irritation:
Conclusion/Summary on mixture : Causes skin irritation.
Page 5 / 8
73
54
Carcinogenicity:
Conclusion/Summary on mixture : No specific data.
Reproductive toxicity:
Conclusion/Summary on mixture : No specific data.
Page 6 / 8
55
Page 7 / 8
56
It is always the responsibility of the user to take all necessary steps to meet the demands of applicable legislation.
The information contained in this safety data sheet does not constitute the user’s own assessment of workplace risks, as
required by other health and safety legislation
Page 8 / 8
57
PAINTING PROCEDURE
Steel Service and Construction
for The Shell Company of Thailand : SCOT Phoenix Project
Painting System LS3-N/M : Un-Insulated Stainless Steel, Serviced temp. 200o C < Temp. < 450o C
MKT-F-04-1-01/06/60
58
No.TH 8009B
Jan' 20
SILBON HB-CUI
SILBON HB-CUI is based on Inorganic copolymer and metallic flake.
It is designed to provide anti-corrosion under insulation for pipe coating which is exposed to continuous
operating temperature -196°C to 650°C . It has the advantages as follow;
1. Excellent adhesion on steel and stainless steel.
2. Excellent anti-corrosion under insulation.
3. Film drying at ambient temperature.
4. Resistance to thermal shock and thermal cycling in service.
5. Prevent stress corrosion cracking.
TECHNICAL DATA
Type : High build Inorganic copolymer heat resistance
Recommended Use : Structure , Pipe , Corrosion under insulation
Mixing Ratio : Base : Accelerator = 100 : 1.8 (by weight)
Colour : Aluminium
Flash Point: Base 25°C Accelerator 90°C
VOC : 339 [g/litre] EPA Method 24
Solid by Volume : 75.0 ± 2%
Coverage (Theoretical) : 0.13 - 0.20 l/m2 ; 7.50 - 5.00 m2/l
Wet Film Thickness : 5.33 - 8.00 mils ; 133 - 200 microns
Dry Film Thickness : 4.00 - 6.00 mils ; 100 - 150 microns
Drying Time : Temperature 10°C 20°C 30°C 40°C
(at D.F.T. 125 microns) : Surface Dry 4 hrs. 3 hrs. 2 hrs. 1 hr.
: Hard Dry 12 hrs. 8 hrs. 6 hrs. 5 hrs.
Painting Interval : Minimum 12 hrs. 8 hrs. 6 hrs. 5 hrs.
(at D.F.T. 125 microns) : Maximum
Pot Life : 12 hrs. 8 hrs. 5 hrs. 3 hrs.
Thinner : Silbon Thinner
Method of Application : Airless spray is recommended. Brush is used only for small area or touch up.
Roller is not recommended for high dry film thickness.
Conditions of Application : Temperature Minimum 10°C
Humidity Maximum 85 % RH
For Airless spray :
Tip No. GRACO 417 , 419 , 421
Paint output pressure 11.7 - 14.7 MPa.
Thinning 5 - 15 % by volume
Recommended Surface- : Steel : Blast cleaning to SSPC-SP 10 , Sa 2½ (ISO 8501-1)
preparation Duplex stainless : Blast cleaning to SSPC-SP16
Anchor profile 30-65 µm are recommended for the highest performance.
Preceding coats : Galbon S-HB , Galbon S-HB PZ-L1 or direct to steel.
Subsequent coats : Silbon HB-CUI
Packaging : Two pack product per set ; 3.785 Litres / Gallon
Shelf life at 25°C : Base 12 months , Accelerator 12 months , In unopened container
Notes ; Surface preparation ; All surface to be coated should be clean, dry and free from contamination.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
59
2. HARZARDS IDENTIFICATION
GHS CLASSIFICATION Category Hazard statement Hazard
Flammable liquids 3 Flammable liquid and vapour
Skin corrosion / irritation 2 Causes skin irritation
Serious eye damage / eye irritation 2A Causes serious eye irritation
Specific target organ toxicity (single exposure) 3 (Respiratory tract irritation)
Specific target organ toxicity (repeated exposure) 2 (Respiratory, nervous system)
Acute hazards to the aquatic environment 2 Toxic to aquatic life
GHS LABEL ELEMENTS
Pictograms
Page 1 / 8
60
4. FIRST-AID MEASURES
4.1 Description of first-aid measures
General
: In all cases of doubt, or when symtoms persist, seek medical attention. Never give anything by mouth
to an unconscious person. If unconcious place in recovery position and seek medical advice.
Eye contact
: Check for and remove any contact lenses. Immediately flush eyes with running clean fresh
water for at least 15 minutes, keeping the eyelids open and seek medical attention.
Skin contact
: Remove contaminated clothing and shoes. Wash skin throughly with soap and water or use
recognised skin cleanser. Do not use solvents or thinners.
Inhalation
: Remove to fresh air. Keep patient warm and at rest. If not breathing, if breathing is irregular
or if respiratory arrest occures, provide artificial respiration or oxygen by trained personnel.
Ingestion
: If accidentally swallow obtain immediate medical attention and show the container or label.
Keep patient warm and at rest. Do not induce vomitting.
4.2. Most important symptoms and effects, both acute and delayed
Potential acute symptoms and effects
Inhalation
Exposure to vapors may cause a health hazard.
Serious effects may be delayed following exposure
Skin contact
Irritating to skin. May cause sensitisation by skin contact.
Eye contact
Irritating to eyes.
Ingestion
Harmful if swallowed
Potential delayed symptoms and effects
Inhalation
No specific data
Skin contact
Adverse symptoms may include the following: irritation, redness
Eye contact
Adverse symptoms may include the following: irritation, watering, redness
Ingestion
Page 2 / 8
61
83
82
81
80
No specific data
4.3. Indication of any immediate medical attention and special treatment needed
Notes to physician
In case of inhalation of decomposition products in a fire, symptoms may be delayed
The exposed person may need to be kept under medical surveillance for 48 hours
Specific treatments
No specific treatment
Page 4 / 8
63
86
For prolonged or repeated handling, use the following type of gloves: gloves; nitrile.
Barrier creams may help to protect the exposed areas of the skin but should not be applied
once exposure has occurred.
For right choice of glove materials, with focus on chemical resistance and time of penetration,
seek advice by the supplier of chemical resistant gloves.
Skin Protection
: Overalls which cover the body, arms and legs should worn. Skinshould not be exposed.
Barrier creams may help to protect areas which are difficult to cover such as face and neck.
They should howerve not be applied once ecposure has occurred. Petroleum jelly based types
Such as vaseline should not be used. All part of the body should be washed after contact.
Skin corrosion/irritation:
Conclusion/Summary on mixture : Causes skin irritation.
Page 5 / 8
64
Carcinogenicity:
Conclusion/Summary on mixture : No specific data.
Reproductive toxicity:
Conclusion/Summary on mixture : No specific data.
Page 6 / 8
65
Page 7 / 8
66
It is always the responsibility of the user to take all necessary steps to meet the demands of applicable legislation.
The information contained in this safety data sheet does not constitute the user’s own assessment of workplace risks, as
required by other health and safety legislation
Page 8 / 8
67
91
PAINTING PROCEDURE
Steel Service and Construction
for The Shell Company of Thailand : SCOT Phoenix Project
Painting System LC3-N : Un-Insulated Carbon Steel, Serviced temp. 200o C < Temp. < 450o C
MKT-F-04-1-01/06/60
68
92
2. HARZARDS IDENTIFICATION
GHS CLASSIFICATION Category Hazard statement Hazard
Flammable liquids 3 Flammable liquid and vapour
Skin corrosion / irritation 2 Causes skin irritation
Serious eye damage / eye irritation 2A Causes serious eye irritation
Specific target organ toxicity (single exposure) 3 (Respiratory tract irritation)
Specific target organ toxicity (repeated exposure) 2 (Respiratory, nervous system)
Acute hazards to the aquatic environment 2 Toxic to aquatic life
GHS LABEL ELEMENTS
Pictograms
Page 1 / 8
69
No.TH 8009B
Jan' 20
SILBON HB-CUI
SILBON HB-CUI is based on Inorganic copolymer and metallic flake.
It is designed to provide anti-corrosion under insulation for pipe coating which is exposed to continuous
operating temperature -196°C to 650°C . It has the advantages as follow;
1. Excellent adhesion on steel and stainless steel.
2. Excellent anti-corrosion under insulation.
3. Film drying at ambient temperature.
4. Resistance to thermal shock and thermal cycling in service.
5. Prevent stress corrosion cracking.
TECHNICAL DATA
Type : High build Inorganic copolymer heat resistance
Recommended Use : Structure , Pipe , Corrosion under insulation
Mixing Ratio : Base : Accelerator = 100 : 1.8 (by weight)
Colour : Aluminium
Flash Point: Base 25°C Accelerator 90°C
VOC : 339 [g/litre] EPA Method 24
Solid by Volume : 75.0 ± 2%
Coverage (Theoretical) : 0.13 - 0.20 l/m2 ; 7.50 - 5.00 m2/l
Wet Film Thickness : 5.33 - 8.00 mils ; 133 - 200 microns
Dry Film Thickness : 4.00 - 6.00 mils ; 100 - 150 microns
Drying Time : Temperature 10°C 20°C 30°C 40°C
(at D.F.T. 125 microns) : Surface Dry 4 hrs. 3 hrs. 2 hrs. 1 hr.
: Hard Dry 12 hrs. 8 hrs. 6 hrs. 5 hrs.
Painting Interval : Minimum 12 hrs. 8 hrs. 6 hrs. 5 hrs.
(at D.F.T. 125 microns) : Maximum
Pot Life : 12 hrs. 8 hrs. 5 hrs. 3 hrs.
Thinner : Silbon Thinner
Method of Application : Airless spray is recommended. Brush is used only for small area or touch up.
Roller is not recommended for high dry film thickness.
Conditions of Application : Temperature Minimum 10°C
Humidity Maximum 85 % RH
For Airless spray :
Tip No. GRACO 417 , 419 , 421
Paint output pressure 11.7 - 14.7 MPa.
Thinning 5 - 15 % by volume
Recommended Surface- : Steel : Blast cleaning to SSPC-SP 10 , Sa 2½ (ISO 8501-1)
preparation Duplex stainless : Blast cleaning to SSPC-SP16
Anchor profile 30-65 µm are recommended for the highest performance.
Preceding coats : Galbon S-HB , Galbon S-HB PZ-L1 or direct to steel.
Subsequent coats : Silbon HB-CUI
Packaging : Two pack product per set ; 3.785 Litres / Gallon
Shelf life at 25°C : Base 12 months , Accelerator 12 months , In unopened container
Notes ; Surface preparation ; All surface to be coated should be clean, dry and free from contamination.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
70
4. FIRST-AID MEASURES
4.1 Description of first-aid measures
General
: In all cases of doubt, or when symtoms persist, seek medical attention. Never give anything by mouth
to an unconscious person. If unconcious place in recovery position and seek medical advice.
Eye contact
: Check for and remove any contact lenses. Immediately flush eyes with running clean fresh
water for at least 15 minutes, keeping the eyelids open and seek medical attention.
Skin contact
: Remove contaminated clothing and shoes. Wash skin throughly with soap and water or use
recognised skin cleanser. Do not use solvents or thinners.
Inhalation
: Remove to fresh air. Keep patient warm and at rest. If not breathing, if breathing is irregular
or if respiratory arrest occures, provide artificial respiration or oxygen by trained personnel.
Ingestion
: If accidentally swallow obtain immediate medical attention and show the container or label.
Keep patient warm and at rest. Do not induce vomitting.
4.2. Most important symptoms and effects, both acute and delayed
Potential acute symptoms and effects
Inhalation
Exposure to vapors may cause a health hazard.
Serious effects may be delayed following exposure
Skin contact
Irritating to skin. May cause sensitisation by skin contact.
Eye contact
Irritating to eyes.
Ingestion
Harmful if swallowed
Potential delayed symptoms and effects
Inhalation
No specific data
Skin contact
Adverse symptoms may include the following: irritation, redness
Eye contact
Adverse symptoms may include the following: irritation, watering, redness
Ingestion
Page 2 / 8
71
No specific data
4.3. Indication of any immediate medical attention and special treatment needed
Notes to physician
In case of inhalation of decomposition products in a fire, symptoms may be delayed
The exposed person may need to be kept under medical surveillance for 48 hours
Specific treatments
No specific treatment
Page 4 / 8
73
For prolonged or repeated handling, use the following type of gloves: gloves; nitrile.
Barrier creams may help to protect the exposed areas of the skin but should not be applied
once exposure has occurred.
For right choice of glove materials, with focus on chemical resistance and time of penetration,
seek advice by the supplier of chemical resistant gloves.
Skin Protection
: Overalls which cover the body, arms and legs should worn. Skinshould not be exposed.
Barrier creams may help to protect areas which are difficult to cover such as face and neck.
They should howerve not be applied once ecposure has occurred. Petroleum jelly based types
Such as vaseline should not be used. All part of the body should be washed after contact.
Skin corrosion/irritation:
Conclusion/Summary on mixture : Causes skin irritation.
Page 5 / 8
72
100
99
74
Carcinogenicity:
Conclusion/Summary on mixture : No specific data.
Reproductive toxicity:
Conclusion/Summary on mixture : No specific data.
Page 6 / 8
75
74
Page 7 / 8
76
It is always the responsibility of the user to take all necessary steps to meet the demands of applicable legislation.
The information contained in this safety data sheet does not constitute the user’s own assessment of workplace risks, as
required by other health and safety legislation
Page 8 / 8
77
PAINTING PROCEDURE
Steel Service and Construction
for The Shell Company of Thailand : SCOT Phoenix Project
Painting System LS1/N : Un-Insulated Stainless Steel, Serviced temp. (-35)o C < Temp. < 120o C
MKT-F-04-1-01/06/60
78
No.TH 6193S
Jan' 20
UMEGUARD SX-HS
UMEGUARD SX-HS is surface tolerant type modified epoxy paint.
It has the following adventages,
1 Excellent compatibility with almost all type of subsequent coat.
2 Excellent physical properties such as toughness , impact and abrasion resistance.
3 Excellent resistance to sea water and cathodic protection.
4 High solid high build and low VOC product.
TECHNICAL DATA
Type : High-solid modified anti-corrosive epoxy polyamide paint
Recommended Use : As surface tolerant primer of epoxy paint system for steel surface.
Mixing Ratio : Base : Hardener = 74 : 26 (by volume) ; 83 : 17 (by weight)
Colour : Black , Reddish Brown , Grey , Green.
Flash Point : Base = 23.5°C Hardener = 27°C
VOC : 232 [g/litre] EPA Method 24
Solid by Volume : 77.0 ± 2%
Coverage (Theoretical) : 0.13 - 0.26 l/m2 ; 7.70 - 3.85 m2/l
Wet Film Thickness : 5.19 - 10.39 mils ; 130 - 260 microns
Dry Film Thickness : 4.00 - 8.00 mils ; 100 - 200 microns
Drying Time : Temperature 10°C 20°C 30°C 40°C
(at D.F.T. 150 microns) : Surface Dry 7 hrs. 3.5 hrs. 1.5 hrs. 45 mins.
: Hard Dry 28 hrs. 12 hrs. 6 hrs. 5 hrs.
Painting Interval : Minimum 28 hrs. 12 hrs. 6 hrs. 5 hrs.
(at D.F.T. 150 microns) : Maximum* - - - -
Pot Life : 5 hrs. 3 hrs. 1.5 hrs. 1 hr.
Thinner : CMP-31
Method of Application : Airless spray , Roller , Brush
Conditions of Application : Temperature Minimum 5°C
Humidity Maximum 85% RH
For Airless spray :
Tip No. GRACO 517, 721
Paint output pressure 14.7 - 17.7 MPa.
Thinning 0 - 15 % by volume
Recommended Surface- : Steel : Blast cleaning to Sa 2½ (ISO 8501-1) , St-3
preparation Anchor profile 30-65 µm are recommended for the highest performance.
Preceding coats : NZ Primes S, Cerabond 2000, Epicon Zinc Rich Primer B-2, etc
Subsequent coats : Wide range of any coating such as , Epoxy , Polyurethane , etc.
Packaging : Two pack product per set ; 3.785 Litres / Gallon , 18.925 Litres / Drum
Shelf life at 25°C : Base 24 months , Hardener 24 months , In unopened container
As nature of epoxy coatings UMEGUARD SX-HS can not avoid chalking yellowing and fading on sunlight exposure
Maximum recoat time is limited. The surface must have a clean, dry surface free of chalk, etc.
Safety period should be coated within 30 days interval.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
79
First-aid measures
General : In all cases of doubt, or when symtoms persist, seek medical attention. Never give anything
by mouth to an unconscious person.
Eye contact : Check for and remove any contact lenses. Immediately flush eyes with running clean fresh
water for at least 15 minutes, keeping the eyelids open and seek medical attention.
Skin contact : Remove contaminated clothing and shoes. Wash skin throughly with soap and water or use
recognised skin cleanser. Do not use solvents or thinners.
Inhalation : Remove to fresh air. Keep patient warm and at rest. If not breathing, if breathing is irregular
or if respiratory arrest occures, provide artificial respiration or oxygen by trained personnel.
Give nothing by mouth. If unconscious, place in recovery position and seek medical advice.
Ingestion : If accidentally swallow obtain immediate medical attention and show the container or label.
Keep patient warm and at rest. Do not induce vomitting.
Page 1 / 6
80
In use : Avoid skin and eye contact. Avoid inhalation of vapours and spray mists.
Smoking, eating and drinking should be prohibited in areas where this material is handled.
Never use pressure to empty. Container is not a pressure vessel. Always keep in containers made
from the same material as the original one.
The product may charge electrostatically. Always use earthing leads when pouring solvents and
transferring product. Operators should wear clothing which does not generate static and
antistatic footwear; floor should be conductive type.
When operators, whether spraying or not, have to work inside the spray booth, ventilation is
unlikely to be sufficient to control particulates and solvent vapour in all case. In such
circumstances they should wear a compressed air-fed respirator during the spraying process
and until such time as the particulates and solvent vapour concentration has fallen below
the exposure limits.
Storage ; Store in accordance with local regulation. Observe label precautions. Store in a cool,
well ventilated area away from incompatible materials and sauce of heat and direct sunlight.
Page 2 / 6
81
79
Storage Store on concrete or other impervious floor, preferably with bunding to contain any spillage.
Do not stack more than 3 pallets high.
Keep container tightly closed. Container that have been opened must be carefully resealed and
kept upright to prevent leakage.
Prevent unauthorised access.
This is highly flammable liquid. Refer to the requirements of local regulations for the storage
and handling regulations petaining to this material.
Wear a full face shield if mixing or pouring operations pose a risk of splashes.
An eyewash station is suggested as a good work place practice.
Hands Protection : Gloves of an appropriate material should worn during mixing and application.
For prolonged or repeated handling, use the following type of gloves: gloves; nitrile.
Barrier creams may help to protect the exposed areas of the skin but should not be applied
once exposure has occurred.
For right choice of glove materials, with focus on chemical resistance and time of penetration,
seek advice by the supplier of chemical resistant gloves.
Skin Protection : Overalls which cover the body, arms and legs should worn. Skinshould not be exposed.
Barrier creams may help to protect areas which are difficult to cover such as face and neck.
They should howerve not be applied once ecposure has occurred. Petroleum jelly based types
Such as vaseline should not be used. All part of the body should be washed after contact.
Page 3 / 6
82
Keep away from oxidising agents, strongly alkaline and strong acid materials in order to avoid possible exothermic reactions.
Exposure to solvent vapour concentration from the component solvents in excess of the state occupational exposure limits may
result in adverse health effects such as mucous and membrane and respiratory system irritation and adverse effects on the
kidneys, liver and central nervous system. Symptoms include headache, nausea, dizziness, fatigue, muscular weakness,
downsiness andin extream cases, loss of consciousness.
Repeated or prolonged contact with the preparation may cause removal of natural fat from the skin resulting in dryness,
irritation and possible non-allergic contact dermatitis. Solvents may also be absorbed through the skin. Splashes of liquid in
the eye may cause irritation and soreness with possible reversibledamage.
Page 4 / 6
83
81
Using information provided in this data sheet advice should be obtained from the Waste
Regulation Authority, whether the special waste regulations apply.
Additional information
ADR / RID : Hazardous identification no. : 30
: Special provision : 640E
IMDG : Class : 3
Proper shipping name : Paint
Emergency schedules (EmS) : F-E, S-E
Marine pollutant : No
Harmful
Page 5 / 6
84
The information on this safety data sheet is based upon the present state of our knowledge and on current law.
The product should not be used for purposes other than shown in the product data sheet without first obtaining written advice.
It is always the responsibility of the user to take all necessary steps to meet the demands of applicable legislation.
The information in this Material Safety Data Sheet is required according to legislation.
Page 6 / 6
85
84
Page 1 / 6
86
85
In use : Avoid skin and eye contact. Avoid inhalation of vapours and spray mists.
Smoking, eating and drinking should be prohibited in areas where this material is handled.
Never use pressure to empty. Container is not a pressure vessel. Always keep in containers made
from the same material as the original one.
The product may charge electrostatically. Always use earthing leads when pouring solvents and
transferring product. Operators should wear clothing which does not generate static and
antistatic footwear; floor should be conductive type.
When operators, whether spraying or not, have to work inside the spray booth, ventilation is
unlikely to be sufficient to control particulates and solvent vapour in all case. In such
circumstances they should wear a compressed air-fed respirator during the spraying process
and until such time as the particulates and solvent vapour concentration has fallen below
the exposure limits.
Storage ; Store in accordance with local regulation. Observe label precautions. Store in a cool,
well ventilated area away from incompatible materials and sauce of heat and direct sunlight.
Page 2 / 6
87
Wear a full face shield if mixing or pouring operations pose a risk of splashes.
An eyewash station is suggested as a good work place practice.
Hands Protection : Gloves of an appropriate material should worn during mixing and application.
For prolonged or repeated handling, use the following type of gloves: gloves; nitrile.
Barrier creams may help to protect the exposed areas of the skin but should not be applied
once exposure has occurred.
For right choice of glove materials, with focus on chemical resistance and time of penetration,
seek advice by the supplier of chemical resistant gloves.
Skin Protection : Overalls which cover the body, arms and legs should worn. Skinshould not be exposed.
Barrier creams may help to protect areas which are difficult to cover such as face and neck.
They should howerve not be applied once ecposure has occurred. Petroleum jelly based types
Such as vaseline should not be used. All part of the body should be washed after contact.
Keep away from oxidising agents, strongly alkaline and strong acid materials in order to avoid possible exothermic reactions.
Page 3 / 6
88
Exposure to solvent vapour concentration from the component solvents in excess of the state occupational exposure limits may
result in adverse health effects such as mucous and membrane and respiratory system irritation and adverse effects on the
kidneys, liver and central nervous system. Symptoms include headache, nausea, dizziness, fatigue, muscular weakness,
downsiness andin extream cases, loss of consciousness.
Repeated or prolonged contact with the preparation may cause removal of natural fat from the skin resulting in dryness,
irritation and possible non-allergic contact dermatitis. Solvents may also be absorbed through the skin. Splashes of liquid in
the eye may cause irritation and soreness with possible reversibledamage.
Using information provided in this data sheet advice should be obtained from the Waste
Regulation Authority, whether the special waste regulations apply.
Page 4 / 6
89
Additional information
ADR / RID : Hazardous identification no. : 30
: Special provision : 640E
IMDG : Class : 3
Proper shipping name : Paint
Emergency schedules (EmS) : F-E, S-E
Marine pollutant : No
Harmful
Contains : Xylene
Page 5 / 6
90
The information on this safety data sheet is based upon the present state of our knowledge and on current law.
The product should not be used for purposes other than shown in the product data sheet without first obtaining written advice.
It is always the responsibility of the user to take all necessary steps to meet the demands of applicable legislation.
The information in this Material Safety Data Sheet is required according to legislation.
Page 6 / 6
91
No.TH 5512
Jan' 20
UNY MARINE HS
UNY MARINE HS, based on acrylic polyol and non-yellowing polyisocyanates resin , has excellent
gloss retention, durability and chemical resistance, etc . It is suitable for protection of tank , tower, bridge
and other steel structures.
TECHNICAL DATA
Type : Acrylic aliphatic polyurethane paint (non yellowing), high solid
Recommended Use : Finish coat of Epoxy system for bridge, chemical plant oil tank
and steel structures, etc.
Mixing Ratio : Base : Hardener = 80 : 20 (by volume) , 5 : 1 (by weight)
Colour : White , as specified
Flash Point : Base = 23.5°C Hardener = 29°C
VOC : 430 [g/litre] EPA method-24
Solid by Volume : 61.0 ± 2%
Coverage (Theoretical) : 0.07 - 0.12 l/m2 ; 15.3 - 8.1 m2/l
Wet Film Thickness : 2.62 - 4.92 mils ; 66 - 123 microns
Dry Film Thickness : 1.60 - 3.00 mils ; 40 - 75 microns
Drying Time : Temperature 10°C 20°C 30°C 40°C
(at D.F.T. 40 microns) : Surface Dry 2 hrs. 1 hr. 30 mins. 15 mins.
: Hard Dry 14 hrs. 8 hrs. 7 hrs. 4 hrs.
Painting Interval : Minimum 6 hrs. 4 hrs. 2 hrs. 1 hr.
(at D.F.T. 40 microns) : Maximum - - - -
Pot Life : 8 hrs. 7 hrs. 6 hrs. 4 hrs.
Thinner : CMP-41
Method of Application : Airless spray , Roller , Brush
Conditions of Application : Temperature Minimum 5°C
Humidity Maximum 85% RH
For Airless spray :
Tip No. GRACO 715 , 813
Paint output pressure 12 - 15 MPa.
Viscosity 25 - 35 sec (Ford Cup No.4)
Thinning 0 - 15 % by volume
Preceding coats : Epicon HB-CL, Epicon HB-NP, Epicon Undercoat , Epicon F-HS ,
Umeguard HS , Umeguard HS Silver, Univan HS , etc.
Subsequent coats : -
Packaging : Two pack product per set ; 3.785 Litres / Gallon , 18.925 Litres / Drum
Shelf life at 25°C : Base 24 months , Hardener 24 months , In unopened container
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
92
No.TH 5512
ม.ค. 63
ยูนิ มารีน เอชเอส
ยูนิ มารีน เอชเอส ประกอบด้วยเรซิ�น อะคริลิค โพลิออล และไอโซไซยาเนตชนิดไม่ขึ�นเหลืองให้คุณสมบัติที�ดีเลิศในด้านคง
ความเงา ทนทาน ต่อสารเคมี ช่วยปกป้องโครงสร้างเหล็กต่างๆ จากแสงอุลตร้าไวโอเล็ต (U.V. PROTECTION) ดังนั�นจึง
เหมาะสําหรับ สะพาน ถังนํ�ามัน โรงงานเคมีและโครงสร้างเหล็กอื�นๆ
ข้อมูลทางเทคนิค
ชนิด : อะคริลิค อะลิฟาติค โพลียูรีเทน (ไม่เหลือง) ชนิดเนื�อสีสูง
การใช้งาน : ใช้เป็นสีทับหน้าในระบบ "อีพอกซี" ที�มีความเงางามเหมาะสําหรับงานสะพาน
ถังนํ�ามันและโครงสร้างเหล็กอื�นๆ
อัตรส่วนผสม : เนื�อสี : นํ�ายา = 80 : 20 (โดยปริมาตร) , 5 : 1 (โดยนํ�าหนัก)
สี : ขาว ,ตามที�ระบุ
จุดวาบไฟ : เนื�อสี 23.5 องศาเซลเซียส นํ�ายา 29 องศาเซลเซียส
ปริมาณสารอินทรีย์ระเหย : 430 [กรัม/ลิตร]
เนื�อสีโดยปริมาตร : 61.0 ± 2%
การปกคลุมพื�นผิวโดยทฤษฏี : 0.07 - 0.12 ลิตร / ต.ร.ม. : 15.3 - 8.1 ต.ร.ม. / ลิตร
ความหนาฟิล์มเมื�อเปียก : 2.62 - 4.92 มิล : 66 - 123 ไมครอน
ความหนาฟิล์มเมื�อแห้ง : 1.60 - 3.00 มิล : 40 - 75 ไมครอน
ระยะเวลาแห้ง : อุณหภูมิ 10°C 20°C 30°C 40°C
ที�ความหนา 40 ไมครอน : แห้งผิว 2 ชั�วโมง 1 ชั�วโมง 30 นาที 15 นาที
: แห้งแข็ง 14 ชั�วโมง 8 ชั�วโมง 7 ชั�วโมง 4 ชั�วโมง
ระยะเวลาแห้งก่อนทาสีทับ : อย่างน้อย 6 ชั�วโมง 4 ชั�วโมง 2 ชั�วโมง 1 ชั�วโมง
ที�ความหนา 40 ไมครอน : อย่างมาก - - - -
อายุการใช้งานหลังผสม : 8 ชั�วโมง 7 ชั�วโมง 6 ชั�วโมง 4 ชั�วโมง
ทินเนอร์ : CMP-41
วิธีใช้งาน : เครื�องพ่นไร้อากาศ , แปรง , ลูกกลิ�ง
ข้อแนะนําการปฎิบัติงาน : อุณหภูมิ อย่างน้อย 5 องศาเซลเซียส
ความชื�นสัมพัทธ์ อย่างมาก 85%
สําหรับเครื�องพ่นไร้อากาศ
ขนาดหัวพ่นกราโค 715 , 813
ความดันที�เครื�องพ่น 12 - 15 เมกาปาสกาล
ความหนืด 25 - 35 วินาที (ถ้วยฟอร์ด เบอร์ 4)
การเจือจาง 0 - 15 % โดยปริมาตร
สีชั�นก่อนทาสีนี� : อิพิคอน เอชบี-ซีแอล, อิพิคอน เอชบี-เอ็นพี, อิพิคอน อันเดอร์โค้ท, อิพิคอน เอฟ-เอชเอส
ยูมิการ์ด เอชเอส, ยูนิแวน เอชเอส, อื�นๆตามที�ระบุในระบบสี
ทาทับด้วยสี : -
ประเภทการบรรจุ : 2 ส่วนผสม ที�ขนาดบรรจุ 3.785 ลิตร/ชุดแกลลอน , 18.925 ลิตร/ชุดถัง
อายุการเก็บที� 25°C : เนื�อสี 24 เดือน , นํ�ายา 24 เดือน ภายในภาชนะที�ไม่ถูกเปิด
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
93
2. HARZARDS IDENTIFICATION
GHS CLASSIFICATION OF MIXTURE Category Hazard statement Hazard
Flammable liquids 3 Flammable liquid and vapour
Acute Toxicity [skin , Dermal] 4 Harmful in contact with skin
Acute Toxicity [inhalation] 4 Harmful if inhaled
Acute Toxicity [ingestion , Oral] 4 Harmful if swallowed
Skin corrosion / irritation 2 Causes skin irritation
Serious eye damage / eye irritation 2A Causes serious eye irritation
Respiratory sensitizer NC.
Skin sensitizer NC.
Germ cell mutagenicity NC.
Carcinogenicity NC.
Reproductive Toxicity NC.
Effects on or via lactation NC.
Specific target organ toxicity (single exposure) 1 (Respiratory, liver, central nervous system,kidney)
Specific target organ toxicity (repeated exposure) 1 (Respiratory, nervous system)
Aspiration toxicity 1 May be fatal if swallowed and enters airways
Acute hazards to the aquatic environment 2 Toxic to aquatic life
Long-term hazards to the aquatic 2 Toxic to aquatic life with long lasting effects
Hazard to the Ozone Layer NC.
GHS LABEL ELEMENTS
Pictograms
Page 1 / 8
94
PRECAUTIONARY STATEMENTS
PREVENTION
P210 : Keep away from heat/sparks/open flames/hot surfaces. - No smoking.
P233 : Keep container tightly closed.
P260 : Do not breathe dust/fume/gas/mist/vapours/spray.
P264 : Wash hand thoroughly after handling.
P272 : Contaminated work clothing should not be allowed out of the workplace.
P273 : Avoid release to the environment.
P280 : Wear protective gloves/protective clothing/eye protection/face protection.
STORAGE
P403 + P233 : Store in a well-ventilated place. Keep container tightly closed.
DISPOSAL
P501 : Dispose of contents and container to appropriate waste site or reclaimer in accordance with local and national regulations.
4. FIRST-AID MEASURES
4.1 Description of first-aid measures
General
: In all cases of doubt, or when symtoms persist, seek medical attention. Never give anything by mouth
to an unconscious person. If unconcious place in recovery position and seek medical advice.
Eye contact
: Check for and remove any contact lenses. Immediately flush eyes with running clean fresh
water for at least 15 minutes, keeping the eyelids open and seek medical attention.
Skin contact
: Remove contaminated clothing and shoes. Wash skin throughly with soap and water or use
recognised skin cleanser. Do not use solvents or thinners.
Inhalation
: Remove to fresh air. Keep patient warm and at rest. If not breathing, if breathing is irregular
Page 2 / 8
95
Page 3 / 8
96
95
Page 4 / 8
97
Carcinogenicity:
Conclusion/Summary on mixture : No specific data.
Reproductive toxicity:
Conclusion/Summary on mixture : No specific data.
Page 6 / 8
99
Page 7 / 8
100
It is always the responsibility of the user to take all necessary steps to meet the demands of applicable legislation.
The information contained in this safety data sheet does not constitute the user’s own assessment of workplace risks, as
required by other health and safety legislation
Page 8 / 8
101
PAINTING PROCEDURE
Steel Service and Construction
for The Shell Company of Thailand : SCOT Phoenix Project
Painting System LC2-N/M : Un-Insulated Carbon Steel, Serviced temp. 120o C < Temp. < 200o C
MKT-F-04-1-01/06/60
102
No.TH 6250
Jan' 20
GALBON S-HB
GALBON S-HB, is an inorganic zinc coating based on ethyl silicate and zinc dust type II per ASTM D-520.
It has zinc content by weight in dry film 86% comform to SSPC Paint No.20 Level 1 and ISO 12944-5. It gives
protection against corrosion prolonged weather resistance, good abrasion.
It also has continuous dry heat resistance up to 400°C and peak at 540°C for 1 hour.
TECHNICAL DATA
Type : Inorganic zinc silicate , high-build type
Recommended Use : As a protective coating outside of tank , pipe, steel structure, etc.
Mixing Ratio : Base : Zinc dust = 30 : 70 (by weight)
Colour : Grey
Flash Point : Base 14.5°C
VOC : 491 [g/litre] EPA method-24
Solid by Volume : 60.0 ± 2%
Coverage (Theoretical) : 0.08 - 0.14 l/m2 ; 12.0 - 7.06 m2/l
Wet Film Thickness : 3.33 - 5.67 mils ; 83 - 142 microns
Dry Film Thickness : 2.00 - 3.40 mils ; 50 - 85 microns
Drying Time : Temperature 10°C 20°C 30°C 40°C
(at D.F.T. 75 microns) : Surface Dry 30 mins. 20 mins. 10 mins. 5 mins.
: Hard Dry 5 hrs. 4 hrs. 3 hrs. 2 hrs.
Painting Interval : Minimum 32 hrs. 20 hrs. 14 hrs. 6 hrs.
(at D.F.T. 75 microns) : Maximum 180 days 180 days 180 days 180 days
Pot Life : 10 hrs. 7 hrs. 5 hrs. 3 hrs.
Thinner : CMP-61
Method of Application : Airless spray, Brush is recommended for small touch up area.
Conditions of Application : Temperature 5 - 50°C
Humidity 50 - 95 % RH
For Airless spray
Tip No. GRACO 419 , 519
Paint output pressure 9.8 MPa.
Viscosity 10-12 sec (Ford Cup No.4)
Thinning 0 - 5% by volume
Surface preparation : Surfaces must be clean and dry ,remove dirt, dust, oil and all other
contaminants that could interfere with adhesion of the next coat.
Steel : Recommend Blast cleaning to Sa 2½ (ISO 8501-1)
Anchor profile 30-65 µm are recommended for the highest performance.
Preceding Coats : Cerabond 2000
Subsequent Coats : Epicon series, Umeguard series , Silicon series, etc
Packaging : Two pack product : 3.8 Litres / Gallon
Shelf life at 25°C : Base 6 months , Zinc dust 12 months , In unopened container
Note ; 1.Dry film thickness in excess of 5.0 mils (125 microns) is not recommended
2.Before apply the next coat the paint film of GALBON S-HB must dry clean and free of zinc salts, etc.
3. Mist coat is required to minimize topcoat bubbling, thinning 30-40% is recommended.
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
103
No.TH 6250
ม.ค. 63
กัลบอน เอส-เอชบี
กัลบอน เอส-เอชบี เป็ นสีประเภทอินออกานิคซิงค์ ซึง่ ประกอบด้วยเอทิล ซิลเิ กตและผงซิงค์ทม่ี คี ณ
ุ ลักษณะตาม ASTM D520
ชนิดที่ 2, ฟิ ลม์ สีเมือ่ แห้งมีปริมาณผงสังกะสี 86% ,มีคณ
ุ สมบัตติ ามคุณลักษณะของ SSPC Paint 20 ระดับ 2 และ ISO 12944-5
ให้คณ ุ สมบัตติ า้ นทานการผุกร่อน ทนต่อสภาวะอากาศได้ยาวนาน ทนต่อสารละลาย น้ ามัน ทนต่อสภาวะอากาศได้ยาวนาน
ทนการขูดขีดได้ดเี ยีย่ มทาให้เกิดเสียหายน้อยเมือ่ มีการเคลือ่ นย้าย
ฟิ ลม์ สีทนต่อความร้อนแห้งแบบต่อเนื่องได้ถงึ 400°C และสามารถทนความร้อนได้สงู ในช่วงเวลา 1 ชัวโมงที่ ่ 540°C
ข้อมูลทางเทคนิ ค
ชนิด : อินออกานิคซิงค์ เอทิลซิลเิ กต ชนิดฟิ ลม์ หนา
การใช้งาน : โครงสร้างเหล็กทัวไป ่ สะพาน ท่อ ซัพพอร์ต และ แทงค์ภายนอก
อัตรส่วนผสม : เนื้อสี : ผงซิงค์ = 30 : 70 (โดยน้ าหนัก)
สี : เทา
จุดวาบไฟ : เนื้อสี 14.5 องศาเซลเซียส
ปริมาณสารอินทรียร์ ะเหย : 491 [กรัม/ลิตร]
เนื้อสีโดยปริมาตร : 60.0 ± 2%
การปกคลุมพืน้ ผิวโดยทฤษฏี : 0.08 - 0.14 ลิตร / ต.ร.ม. : 12.0 - 7.06 ต.ร.ม. / ลิตร
ความหนาฟิ ลม์ เมือ่ เปี ยก : 3.33 - 5.67 มิล : 83 - 142 ไมครอน
ความหนาฟิ ลม์ เมือ่ แห้ง : 2.00 - 3.40 มิล : 50 - 85 ไมครอน
ระยะเวลาแห้ง : อุณหภูม ิ 10°C 20°C 30°C 40°C
ทีค่ วามหนา 75 ไมครอน : แห้งผิว 30 นาที 20 นาที 10 นาที 5 นาที
: แห้งแข็ง 5 ชัวโมง
่ 4 ชัวโมง
่ 3 ชัวโมง
่ 2 ชัวโมง
่
ระยะเวลาแห้งก่อนทาสีทบั : อย่างน้อย 32 ชัวโมง
่ 20 ชัวโมง
่ 14 ชัวโมง ่ 6 ชัวโมง
่
ทีค่ วามหนา 75 ไมครอน : อย่างมาก 180 วัน 180 วัน 180 วัน 180 วัน
อายุการใช้งานหลังผสม : 10 ชัวโมง่ 7 ชัวโมง
่ 5 ชัวโมง่ 3 ชัวโมง่
ทินเนอร์ : CMP-61
วิธใี ช้งาน : เครือ่ งพ่นไร้อากาศ , แปรงสาหรับพืน้ ทีข่ นาดเล็ก
ข้อแนะนาการปฎิบตั งิ าน : อุณหภูม ิ อย่างน้อย 5 - 50 องศาเซลเซียส
ความชืน้ สัมพัทธ์ อย่างมาก 50 - 95 %
สาหรับเครือ่ งพ่นไร้อากาศ
ขนาดหัวพ่นกราโค 419 , 519
ความดันทีเ่ ครือ่ งพ่น 9.8 เมกาปาสกาล
ความหนืด 10 - 12 วินาที (ถ้วยฟอร์ด เบอร์ 4)
การเจือจาง 0 - 5 % โดยปริมาตร
แนะนาการเตรียมพืน้ ผิว : เหล็ก : โดยการพ่นทาความสะอาดให้ได้เกรดระดับ Sa 2½ (ISO 8501-1)
เพือ่ ประสิทธิภาพสูงสุด แนะนา ทีค่ วามหยาบ 30 - 65 ไมครอน
สีชนั ้ ก่อนทาสีน้ี : เซราบอนด์ 2000
ทาทับด้วยสี : อิพคิ อน ซีรย่ี ์ , ยูมกิ าร์ด ซีรย่ี ์ , ซิลคิ อน ซีรย่ี ์, อื่นๆตามทีร่ ะบุในระบบสี
ประเภทการบรรจุ : 2 ส่วนผสม ทีข่ นาดบรรจุ 3.8 ลิตร/ชุดแกลลอน
อายุการเก็บที่ 25°C : เนื้อสี 6 เดือน , ผงซิงค์ 12 เดือน ภายในภาชนะทีไ่ ม่ถกู เปิ ด
ไม่แนะนาให้มคี วามหนาฟิ ลม์ เกิน 125 ไมครอน การทา Mist coat เพือ่ ลดการเกิดฟองของสีชนถั ั ้ ดไป แนะนาให้ผสมทินเนอร์ท่ี 30-40%
พืน้ ผิวก่อนทาสีชนถั
ั ้ ดไปบนฟิ ลม์ สีตอ้ งไม่มสี นิม สะอาด แห้ง ไม่มคี ราบเกลือ ฝุ่นผง น้ ามัน บนพืน้ ผิว
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
104
103
2. HARZARDS IDENTIFICATION
GHS CLASSIFICATION Category Hazard statement Hazard
Flammable liquids 2 Highly Flammable liquid and vapour
Acute Toxicity [skin , Dermal] 4 Harmful in contact with skin
Acute Toxicity [inhalation] 4 Harmful if inhaled
Acute Toxicity [ingestion , Oral] 4 Harmful if swallowed
Skin corrosion / irritation 3 Causes mild skin irritation
Serious eye damage / eye irritation 2A Causes serious eye irritation
Specific target organ toxicity (single exposure) 3 May cause respiratory irritation drowsiness or dizziness
Specific target organ toxicity (repeated exposure) 2 Respiratory, Liver , Kidney , Central Nervous system)
Aspiration toxicity 1 May be fatal if swallowed and enters airways
Acute hazards to the aquatic environment 3 Harmful to aquatic life
Long-term hazards to the aquatic 3 Harmful to aquatic life with long lasting effects
GHS LABEL ELEMENTS
Pictograms
PRECAUTIONARY STATEMENTS
Page 1 / 8
105
PREVENTION
P210 : Keep away from heat/sparks/open flames/hot surfaces. - No smoking.
P233 : Keep container tightly closed.
P260 : Do not breathe dust/fume/gas/mist/vapours/spray.
P264 : Wash hand thoroughly after handling.
P272 : Contaminated work clothing should not be allowed out of the workplace.
P273 : Avoid release to the environment.
P280 : Wear protective gloves/protective clothing/eye protection/face protection.
STORAGE
P403 + P233 : Store in a well-ventilated place. Keep container tightly closed.
DISPOSAL
P501 : Dispose of contents and container to appropriate waste site or reclaimer in accordance with local and national regulations.
4. FIRST-AID MEASURES
4.1 Description of first-aid measures
General
: In all cases of doubt, or when symtoms persist, seek medical attention. Never give anything by mouth
to an unconscious person. If unconcious place in recovery position and seek medical advice.
Eye contact
: Check for and remove any contact lenses. Immediately flush eyes with running clean fresh
water for at least 15 minutes, keeping the eyelids open and seek medical attention.
Skin contact
: Remove contaminated clothing and shoes. Wash skin throughly with soap and water or use
recognised skin cleanser. Do not use solvents or thinners.
Inhalation
: Remove to fresh air. Keep patient warm and at rest. If not breathing, if breathing is irregular
or if respiratory arrest occures, provide artificial respiration or oxygen by trained personnel.
Ingestion
: If accidentally swallow obtain immediate medical attention and show the container or label.
Page 2 / 8
106
105
Page 3 / 8
107
Page 4 / 8
108
Page 5 / 8
109
Carcinogenicity:
Conclusion/Summary on mixture : No specific data.
Reproductive toxicity:
Conclusion/Summary on mixture : No specific data.
Aspiration hazard:
Conclusion/Summary on mixture : No specific data.
Potential acute health effects
Inhalation : Exposure to vapours may cause a health hazard.
Page 6 / 8
110
Page 7 / 8
111
110
Paint and waste should be disposed in small pieces by the open type of incinerator to have absorbed them with diatomite.
Containers which are not properly cleaned may contain (highly) flammable or explosive vapours.
Special precautions:
Use appropriate protective equipment for the removal and / or disposal of this product
Packing group II II II
Environmental hazard No Yes No
Marine pollutant - Yes -
It is always the responsibility of the user to take all necessary steps to meet the demands of applicable legislation.
The information contained in this safety data sheet does not constitute the user’s own assessment of workplace risks, as
required by other health and safety legislation
Page 8 / 8
112
No.TH 8026
Jan' 20
SILICON AS
SILICON AS as based on silicone acrylic resin, has excellent heat-resistance and weathering resistance.
It has the following advantages :-
1. It has excellent heat resistance up to 260°C
2. It has excellent adhesion property.
3. It has excellent weathering resistance.
TECHNICAL DATA
Type : Silicone resin heat resisting paint
Recommended Use : Boiler, Cylinder of engine, the inside of the exhaust pipe,
Radiator Stove, Oil burner, steam pipe, etc.
Colour : White , Grey , As specified.
Flash Point : 27°C
VOC : 540 [g/litre] EPA Method-24
Solid by Volume : 37.0 ± 2%
Coverage (Theoretical) : 0.08 - 0.14 l/m2 ; 12.3 - 7.4 m2/l
Wet Film Thickness : 3.24 - 5.41 mils ; 81 - 135 microns
Dry Film Thickness : 1.20 - 2.00 mils ; 30 - 50 microns
Drying Time : Temperature 10°C 20°C 30°C 40°C
(at D.F.T. 30 microns) : Surface Dry 50 mins. 30 mins. 20 mins. 10 mins.
: Hard Dry 8 hrs. 5 hrs. 3 hrs. 1.5 hrs.
Painting Interval : Minimum 12 hrs. 8 hrs. 5 hrs. 2.5 hrs.
(at D.F.T. 30 microns) : Maximum - - - -
Thinner : CMP-91
Method of Application : Airless spray , Brush
Conditions of Application : Temperature Minimum 10°C
Humidity Maximum 85% RH
For Airless spray :
Tip No. GRACO 415
Paint output pressure 8.8 - 11.8 MPa.
Viscosity 25 - 30 sec (Ford Cup No.4 )
Thinning 0 - 15 % by volume
Preceding coats : Galbon S-HB , Galbon S-HB 100 , etc.
Subsequent coats :
Packaging : One pack product ; 3.785 Litres / Gallon , 18.925 Litres / Drum
Shelf life at 25°C : In unopened container 24 months
The information given in this sheet is effective at the date shown above and subject to revision from time to time without notice.
113
112
2. HARZARDS IDENTIFICATION
GHS CLASSIFICATION Category Hazard statement Hazard
Flammable liquids 3 Flammable liquid and vapour
Acute Toxicity [skin , Dermal] 4 Harmful in contact with skin
Acute Toxicity [inhalation] 4 Harmful if inhaled
Acute Toxicity [ingestion , Oral] 4 Harmful if swallowed
Skin corrosion / irritation 2 Causes skin irritation
Serious eye damage / eye irritation 2A Causes serious eye irritation
Respiratory sensitizer NC.
Skin sensitizer NC.
Germ cell mutagenicity NC.
Carcinogenicity NC.
Reproductive Toxicity NC.
Effects on or via lactation NC.
Specific target organ toxicity (single exposure) 1 (Respiratory, liver, central nervous system,kidney)
Specific target organ toxicity (repeated exposure) 1 (Respiratory, nervous system)
Aspiration toxicity 1 May be fatal if swallowed and enters airways
Acute hazards to the aquatic environment 2 Toxic to aquatic life
Long-term hazards to the aquatic 2 Toxic to aquatic life with long lasting effects
Hazard to the Ozone Layer NC.
GHS LABEL ELEMENTS
Pictograms
Page 1 / 8
114
113
PRECAUTIONARY STATEMENTS
PREVENTION
P210 : Keep away from heat/sparks/open flames/hot surfaces. - No smoking.
P233 : Keep container tightly closed.
P260 : Do not breathe dust/fume/gas/mist/vapours/spray.
P264 : Wash hand thoroughly after handling.
P272 : Contaminated work clothing should not be allowed out of the workplace.
P273 : Avoid release to the environment.
P280 : Wear protective gloves/protective clothing/eye protection/face protection.
STORAGE
P403 + P233 : Store in a well-ventilated place. Keep container tightly closed.
DISPOSAL
P501 : Dispose of contents and container to appropriate waste site or reclaimer in accordance with local and national regulations.
4. FIRST-AID MEASURES
4.1 Description of first-aid measures
General
: In all cases of doubt, or when symtoms persist, seek medical attention. Never give anything by mouth
to an unconscious person. If unconcious place in recovery position and seek medical advice.
Eye contact
: Check for and remove any contact lenses. Immediately flush eyes with running clean fresh
water for at least 15 minutes, keeping the eyelids open and seek medical attention.
Skin contact
: Remove contaminated clothing and shoes. Wash skin throughly with soap and water or use
recognised skin cleanser. Do not use solvents or thinners.
Inhalation
: Remove to fresh air. Keep patient warm and at rest. If not breathing, if breathing is irregular
or if respiratory arrest occures, provide artificial respiration or oxygen by trained personnel.
Page 2 / 8
115
114
Ingestion
: If accidentally swallow obtain immediate medical attention and show the container or label.
Keep patient warm and at rest. Do not induce vomitting.
4.2. Most important symptoms and effects, both acute and delayed
Potential acute symptoms and effects
Inhalation
Exposure to vapors may cause a health hazard.
Serious effects may be delayed following exposure
Skin contact
Irritating to skin. May cause sensitisation by skin contact.
Eye contact
Irritating to eyes.
Ingestion
Harmful if swallowed
Potential delayed symptoms and effects
Inhalation
No specific data
Skin contact
Adverse symptoms may include the following: irritation, redness
Eye contact
Adverse symptoms may include the following: irritation, watering, redness
Ingestion
No specific data
4.3. Indication of any immediate medical attention and special treatment needed
Notes to physician
In case of inhalation of decomposition products in a fire, symptoms may be delayed
The exposed person may need to be kept under medical surveillance for 48 hours
Specific treatments
No specific treatment
Page 3 / 8
116
Contain and collect spillage with non-combustible absorbent materials, e.g. sand, earth, vermiculite,
diatomaceous earth and place in container for disposal according to local regulations (see section 13).
Clean preferably with a detergent - avoid use of solvents
6.4. Reference to other sections
See Section 1 for emergency contact information.
See Section 8 for information on appropriate personal protective equipment.
See Section 13 for additional waste treatment information
Page 4 / 8
117
116
Page 5 / 8
118
Skin corrosion/irritation:
Conclusion/Summary on mixture : Causes skin irritation.
: Method: Additivity approach, no testdata available.
Serious eye damage/irritation:
Conclusion/Summary on mixture : No specific data.
Carcinogenicity:
Conclusion/Summary on mixture : No specific data.
Reproductive toxicity:
Conclusion/Summary on mixture : No specific data.
Page 6 / 8
119
Page 7 / 8
120
It is always the responsibility of the user to take all necessary steps to meet the demands of applicable legislation.
The information contained in this safety data sheet does not constitute the user’s own assessment of workplace risks, as
required by other health and safety legislation
Page 8 / 8
121