Professional Documents
Culture Documents
I BODY
E
CONTENTS
WINDSHIELD GLASS ................................................ 2 FRONT DOOR GLASS AND REGULATOR ............. 28 F
Removal and Installation .......................................... 2 Removal and Installation ........................................ 28
BACK DOOR WINDOW GLASS ................................ 3 INSIDE MIRROR ....................................................... 29
Removal and Installation .......................................... 3 Removal and Installation ........................................ 29 G
SIDE WINDOW GLASS .............................................. 4 REAR WINDOW DEFOGGER .................................. 30
Removal and Installation .......................................... 4 Component Parts and Harness Connector Location... 30
POWER WINDOW SYSTEM ...................................... 5 EXCEPT FOR SOUTH AFRICA .......................... 30
H
Component Parts and Harness Connector Location..... 5 SOUTH AFRICA .................................................. 31
EXCEPT FOR SOUTH AFRICA ........................... 5 Schematic – DEF – Except for South Africa ........... 32
SOUTH AFRICA ................................................... 6 Wiring Diagram –DEF–/LHD Models ...................... 33
Schematic/ LHD Models ........................................... 7 Wiring Diagram –DEF–/RHD Models (Except for GW
Wiring Diagram – WINDOW –/ LHD Models ............ 8 South Africa) ........................................................... 36
Schematic/ RHD Models (Except for South Africa)....11 Schematic – DEF – For South Africa ...................... 40
Wiring Diagram – WINDOW –/ RHD Models (Except Wiring Diagram –DEF–/ For South Africa ............... 41 J
for South Africa) ..................................................... 12 Terminal and Reference Value for BCM ................. 45
Schematic/ For South Africa .................................. 15 LHD MODELS ..................................................... 45
Wiring Diagram – WINDOW –/ For South Africa ... 16 RHD MODELS (EXCEPT FOR SOUTH AFRICA)... 45
K
Terminal and Reference Value for BCM ................. 19 SOUTH AFRICA .................................................. 45
LHD MODELS ..................................................... 19 Terminal and Reference Value for IPDM E/R ......... 46
RHD MODELS (EXCEPT FOR SOUTH AFRICA)... 19 LHD MODELS ..................................................... 46
FOR SOUTH AFRICA ......................................... 20 RHD MODELS (EXCEPT FOR SOUTH AFRICA)... 46 L
Terminal and Reference Value for Power Window SOUTH AFRICA .................................................. 46
Main Switch ............................................................ 21 Terminal and Reference Value for Unified Meter and
LHD MODELS ..................................................... 21 A/C Amp. ................................................................ 47 M
RHD MODELS (EXCEPT FOR SOUTH AFRICA)... 22 Trouble Diagnosis Symptom Chart ......................... 47
FOR SOUTH AFRICA ......................................... 22 Filament Check ....................................................... 48
Terminal and Reference Value for Power Window Filament Repair ...................................................... 49
Sub-Switch ............................................................. 23 REPAIR EQUIPMENT ......................................... 49
LHD MODELS ..................................................... 23 REPAIRING PROCEDURE ................................. 49
RHD MODELS (EXCEPT FOR SOUTH AFRICA)... 24 DOOR MIRROR ........................................................ 50
FOR SOUTH AFRICA ......................................... 25 Wring Diagram –MIRROR– /For LHD Models ....... 50
Trouble Diagnoses Symptom Chart ....................... 27 Wring Diagram –MIRROR– /For RHD Models ...... 51
Removal and Installation ........................................ 53
PIIA8724E
GW
PIIA6792E
M
1. Back door window molding 2. Dual lock fastener 3. Back door
4. Dam rubber 5. Back door window glass 6. Grommet
PIIA9168E
GW
PIIB7867E
SOUTH AFRICA
PIIB7868E
GW
TIWT1762E
TIWT1763E
GW
TIWT1764E
TIWT0600E
GW
TIWT1765E
Wiring Diagram – WINDOW –/ RHD Models (Except for South Africa) GIS000M7
TIWT1766E
GW
TIWT1767E
TIWT1768E
GW
TIWT1154E
TIWT1769E
GW
TIWT1770E
TIWT1771E
LHD MODELS A
Signal
TERMI- WIRE VOLTAGE (V)
ITEM input/ CONDITION
NAL COLOR (Approx.)
output B
Ignition switch ACC power Ignition switch
11 LG Input Battery voltage
supply (ACC or ON) (ACC or ON position)
ON (open) 0 C
12 P Passenger side door switch Input
OFF (closed) Battery voltage
Input/
22 Y Power window serial link —
output
E
PIIA2344J
54 W
Power window switch power
Input — Battery voltage
K
supply
55 R Power source (Fusible link) Input — Battery voltage
ON (open) 0 L
62 L Driver side door switch Output
OFF (closed) Battery voltage
Input/
22 Y Power window serial link —
output
PIIA2344J
Signal
TER- WIRE VOLTAGE (V)
ITEM input/ CONDITION
MINAL COLOR (Approx.)
output
Input/
39 L CAN-H — —
output
Input/
40 P CAN-L — —
output
42 GY Power source (Fuse) Input — Battery voltage
52 B/W Ground — — 0
IGN SW ON Battery voltage
Within 45 second after igni-
Battery voltage
tion switch is turned to OFF
53 Y/B Rap signal Output
When driver side or passen-
ger side door is open in 0
power window timer operates
Power window switch power
54 W Input — Battery voltage
supply
55 R Power source (Fusible link) Input — Battery voltage
ON (open) 0
62 L/W Driver side door switch Output
OFF (closed) Battery voltage
Input/
74 Y Power window serial link —
output
PIIA2344J
Terminal and Reference Value for Power Window Main Switch GIS000M9
LHD MODELS A
Signal
TERMI- WIRE VOLTAGE (V)
ITEM Input/ CONDITION
NAL COLOR (ApproX.)
output B
1 W BAT power supply Input — Battery voltage
5 OR Encoder power supply Input — 10
C
Key cylinder switch lock sig- Key position
6 B/R Output 5→0
nal (Neutral → Locked)
Key cylinder switch unlock Key position
7 SB Output 5→0 D
signal (Neutral → Unlocked)
Driver side
When power window motor
8 L power window motor UP sig- Output Battery voltage
UP operation.
nal E
Driver side door window is
between fully-open and just
0
before fully-closed position
F
(ON).
9 Y Limit switch signal Output
Driver side door window is
between just before fully-
5 G
closed position and fully-
closed position (OFF).
IGN SW ON Battery voltage
H
Within 45 second after igni-
Battery voltage
tion switch is turned to OFF
10 BR Rap signal Output
When driver side or passen-
ger side door is open in power 0 GW
window timer operates
Driver side
When power window motor
11 G power window motor DOWN Output Battery voltage J
DOWN operation.
signal
K
Input/
12 PU/W Power window serial link —
Output
L
PIIA2344J
OCC3383D
Input/
12 G/B Power window serial link —
output
PIIA2344J
OCC3383D
WIRE Signal
TER- VOLTAGE (V)
COLO ITEM input/ CONDITION A
MINAL (ApproX.)
R output
When soft top open/close func-
Power window down request tion starts and window down 0 B
4 P Output function is operating.
signal
Except the above 5
5 GY Encoder power supply Input — 10 C
Driver side
When power window motor
8 L power window motor UP sig- Output Battery voltage
UP operation.
nal D
Driver side door window is
between fully-open and just
0
before fully-closed position
(ON). E
9 BR Limit switch signal Output
Driver side door window is
between just before fully-closed
5
position and fully-closed posi- F
tion (OFF).
IGN SW ON Battery voltage
Within 45 second after ignition G
Battery voltage
switch is turned to OFF
10 LG Rap signal Output
When driver side or passenger
side door is open in power win- 0 H
dow timer operates
Driver side
When power window motor
11 G power window motor DOWN Output Battery voltage
DOWN operation. GW
signal
J
Input/
12 G/B Power window serial link —
output
K
PIIA2344J
OCC3383D
LHD MODELS
WIRE Signal
TER- VOLTAGE (V)
COLO ITEM input/ CONDITION
MINAL (Approx)
R output
Limit switch and encoder
3 GY — — 0
ground
4 R Encoder power supply Input — 10
WIRE Signal
TER- VOLTAGE (V)
COLO ITEM input/ CONDITION
MINAL (Approx)
R output
Passenger side
When power window motor
8 L power window motor UP sig- Output Battery voltage
UP operation.
nal
Passenger side
When power window motor
9 G power window motor DOWN Output Battery voltage
DOWN operation.
signal
10 W BAT power supply Input — Battery voltage
11 B Ground — — 0
OCC3383D
Input/
16 SB Power window serial link —
output
PIIA2344J
OCC3383D
WIRE Signal
TER- VOLTAGE (V)
COLO ITEM input/ CONDITION A
MINAL (Approx)
R output
When soft top open/close func-
Power window down request tion starts and window down 0 B
13 P Output function is operating.
signal
Except the above 5
Passenger side door window is C
between fully-open and just
0
before fully-closed position
(ON).
15 BR Limit switch signal Output D
Passenger side door window is
between just before fully-
5
closed position and fully-
closed position (OFF). E
Input/
F
16 OR Power window serial link —
output
G
PIIA2344J
M
Input/ When power window motor
12 SB Encoder pulse signal
output operates.
OCC3383D
Signal
TERMI- WIRE VOLTAGE (V)
ITEM input/ CONDITION
NAL COLOR (Approx)
output
Passenger side door window is
between fully-open and just
0
before fully-closed position
(ON).
15 BR Limit switch signal Output
Passenger side door window is
between just before fully-
5
closed position and fully-closed
position (OFF).
Input/
16 OR Power window serial link —
output
PIIA2344J
A
Make sure that other systems using the signal of the following systems operate normally.
Symptom Diagnoses / service procedure
1. Check BCM power supply and ground circuit B
None of the power windows can be operated using any 2. Check power window switch power supply circuit
switch. 3. Check power window serial link
C
4. Replace BCM.
1. Check driver side power window motor circuit
2. Check power window main switch power supply and ground D
Driver side power window cannot be operated
circuit
3. Replace the power window main switch.
1. Check passenger side power window motor circuit E
2. Check power window sub-switch power supply circuit
Passenger side power window cannot be operated.
3. Check power window serial link
4. Replace BCM.
F
Anti-pinch system does not operate normally (driver side). 4. Door window sliding part malfunction
● A foreign material adheres to window glass or grass run rub- H
ber.
● Glass run rubber wear or deformation.
● Sash is tilted too much, or not enough. GW
1. Limit switch adjusting
2. Check limit switch circuit (passenger side)
J
3. Check encoder circuit (passenger side)
Anti-pinch system does not operate normally (passenger 4. Door window sliding part malfunction
side).
● A foreign material adheres to window glass or grass run rub- K
ber.
● Glass run rubber wear or deformation.
● Sash is tilted too much, or not enough. L
1. Check the retained power operation mode setting.
Power window retained power operation does not operate
2. Check door switch
properly.
3. Replace BCM. M
1. Check door switch
2. Limit switch adjusting
3. Check limit switch circuit (driver side)
Automatic window adjusting function does not operate.
4. Check limit switch circuit (passenger side)
5. Check power window serial link
6. Replace BCM.
1. Check door key cylinder switch
Does not operate by the key cylinder switch. 2. Check driver side power window motor circuit
(Except for the Middle East, Brazil and Argentina) 3. Check power window switch power supply and ground circuit
4. Replace the power window main switch.
1. Check power window serial link
Power window lock switch does not function.
2. Replace the power window main switch.
PIIA2156E
PIIA6795E
G
1. Inside mirror
H
GW
PIIB7869E
SOUTH AFRICA
A
GW
J
PIIB7870E
TIWT0975E
GW
TIWT1595E
TIWT1772E
GW
TIWT1773E
TIWT1774E
GW
TIWT1775E
TIWT1776E
GW
TIWT1777E
TIWT0570E
GW
TIWT1778E
TIWT1779E
GW
TIWT1780E
TIWT1781E
LHD MODELS A
11 LG
Ignition switch ACC power supply
Input
Ignition switch
Battery voltage
C
(ACC or ON) (ACC or ON position)
Ignition switch ON power supply Ignition switch
38 W/L Input Battery voltage
(ON or START) (ON or START position) D
39 L CAN-H Input/output — —
40 P CAN-L Input/output — —
42 GY Power source (Fuse) Input — Battery voltage E
52 B Ground — — 0
55 R Power source (Fusible link) Input — Battery voltage
F
RHD MODELS (EXCEPT FOR SOUTH AFRICA)
WIRE Signal VOLTAGE (V)
TERMINAL
COLOR
ITEM
input/output
CONDITION
(Approx.)
G
SOUTH AFRICA L
Signal
WIRE VOLTAGE (V)
TERMINAL ITEM input/out- CONDITION
COLOR (Approx.)
put M
7 R BAT power supply Input — Battery voltage
8 B Ground — — 0
35 W/L IGN power supply Input IGN ON or START Battery voltage
When rear window defogger switch is
0
Rear window defogger ON.
69 L/R Output
switch signal When rear window defogger switch is
5
OFF.
Input/out-
70 L CAN-H — —
put
Input/out-
71 P CAN-L — —
put
Input/out-
72 GY K-line — —
put
LHD MODELS
TERMI- WIRE Signal VOLTAGE (V)
ITEM CONDITION
NAL COLOR input/output (Approx.)
5 P BAT power supply Input — Battery voltage
6 * BAT power supply Input — Battery voltage
38 B Ground (power) Input — 0
48 L CAN-H Input/output — —
49 P CAN-L Input/output — —
When rear window defogger
0
Rear window defogger relay switch is ON.
52 W Output
control signal When rear window defogger
Battery voltage
switch is OFF.
60 B Ground (Signal) — — 0
* = L : For Middle East, Brazil and Argentina.
W : Except for Middle East, Brazil and Argentina.
SOUTH AFRICA
WIRE Signal VOLTAGE (V)
TERMINAL ITEM CONDITION
COLOR input/output (Approx.)
5 P BAT power supply Input — Battery voltage
6 L BAT power supply Input — Battery voltage
38 B/W Ground (power) — — 0
Input/out-
48 L CAN-H — —
put
Input/out-
49 P CAN-L — —
put
When rear window defogger switch
0
Rear window defogger relay is ON.
52 W Output
control signal When rear window defogger switch
Battery voltage
is OFF.
60 B/W Ground (Signal) — — 0
Terminal and Reference Value for Unified Meter and A/C Amp. GIS000N5
A
Signal
TERMI- WIRE VOLTAGE (V)
ITEM input/out- CONDITION
NAL COLOR (Approx.)
put
B
21 R/W BAT power supply Input — Battery voltage
22 Y/G IGN power supply Input IGN ON or START Battery voltage
29 B Ground — — 0 C
30 B Ground — — 0
When rear window defogger switch is
0 D
Rear window defogger switch ON.
38 L/R Output
signal When rear window defogger switch is
5
OFF.
When rear window defogger switch is
E
Battery voltage
Rear window defogger ON sig- ON.
56 B/W Output
nal When rear window defogger switch is
0
OFF. F
72 — Indicator power supply Output IGN ON or START 5
When rear window defogger switch is
0 G
Rear window defogger indicator ON.
78 — Output
signal When rear window defogger switch is
5
OFF.
A/C control push switch power
H
84 — Output IGN ON or START 5
supply
When rear window defogger switch is
0 GW
Rear window defogger switch ON.
87 — Output
ON signal When rear window defogger switch is
5
OFF.
J
Trouble Diagnosis Symptom Chart GIS000N8
Make sure that other systems using the signal of the following systems operate normally.
Symptom Diagnosis / service procedure K
1. CAN communication inspection using CONSLUT-II (self-
diagnosis)
L
2. Check IPDM E/R operation
Rear window defogger does not operate. 3. Check rear window defogger switch circuit
(When rear window defogger switch is in ON, rear win-
4. Check rear window defogger power supply circuit M
dow defogger switch indicator does not illuminate.)
5. Check rear window defogger circuit
6. Check filament
7. Replace IPDM E/R.
Rear window defogger does not operate but door mirror 1. Check rear window defogger circuit
defoggers operate. (With door mirror defogger) 2. Check filament
Both of door mirror defoggers do not operate but rear
Check door mirror defogger power supply circuit
window defogger operates. (With door mirror defogger)
Driver side door mirror defogger does not operate. Check driver side door mirror defogger circuit
Passenger side door mirror defogger does not operate. Check passenger side door mirror defogger circuit
1. When measuring voltage, wrap tin foil around the top of the neg-
ative probe. Then press the foil against the wire with your finger.
SEL122R
SEL263
SEL265
REPAIR EQUIPMENT A
● Conductive silver composition (Dupont No. 4817 or equivalent)
● Ruler 30 cm (11.8 in) long
B
● Drawing pen
● Heat gun
● Alcohol
C
● Cloth
REPAIRING PROCEDURE
1. Wipe broken heat wire and its surrounding area clean with a D
cloth dampened in alcohol.
2. Apply a small amount of conductive silver composition to tip of
drawing pen. E
Shake silver composition container before use.
3. Place ruler on glass along broken line. Deposit conductive silver
composition on break with drawing pen. Slightly overlap existing F
heat wire on both sides [preferably 5 mm (0.20 in)] of the break.
PIIA0215E G
4. After repair has been completed, check repaired wire for conti-
nuity. This check should be performed 10 minutes after silver H
composition is deposited.
Do not touch repaired area while test is being performed.
GW
SEL012D
K
5. Apply a constant stream of hot air directly to the repaired area
for approximately 20 minutes with a heat gun. A minimum dis-
tance of 3 cm (1.2 in) should be kept between repaired area and L
hot air outlet.
If a heat gun is not available, let the repaired area dry for 24
hours. M
SEL013D
TIWT1601E
GW
TIWT1675E
TIWT1676E
PIIA2165E
GW