Professional Documents
Culture Documents
I BODY
E
CONTENTS
MODIFICATION NOTICE ............................................ 3 FRONT DOOR LOCK ............................................... 28 F
Major Modification Notice ......................................... 3 Component Parts Location ..................................... 28
HOOD ......................................................................... 4 REAR DOOR LOCK ................................................. 29
Fitting Adjustment .................................................... 4 Component Parts Location ..................................... 29 G
FRONT END HEIGHT ADJUSTMENT AND LAT- BACK DOOR ............................................................ 30
ERAL/LONGITUDINAL CLEARANCE ADJUST- Fitting Adjustment ................................................... 30
MENT .................................................................... 4 VERTICAL/LATERAL CLEARANCE (SURFACE
H
SURFACE MISMATCH ADJUSTMENT ................ 4 DIFFERENCE) ADJUSTMENT ........................... 30
Removal and Installation .......................................... 5 Removal and Installation of Back Door Weatherstrip... 31
Removal and Installation of Hood Lock Control ....... 6 BACK DOOR OPENER ............................................ 32
RADIATOR CORE SUPPORT .................................... 7 Component Parts and Harness Connector Location... 32 BL
Removal and Installation .......................................... 7 Wiring Diagram — B/DOOR — / For LHD Models... 33
FRONT FENDER ........................................................ 8 Wiring Diagram — B/DOOR — / For RHD Models... 34
Removal and Installation .......................................... 8 Terminal and Reference Value for BCM ................. 35 J
POWER DOOR LOCK SYSTEM ................................ 9 Trouble Diagnosis Chart by Symptom .................... 35
Component Parts and Harness Connector Location..... 9 TRUNK LID ............................................................... 36
Wiring Diagram — D/LOCK — / For LHD Models Fitting Adjustment ................................................... 36
K
(With Power Window) ..............................................11 LONGITUDINAL AND LATERAL CLEARANCE
Wiring Diagram — D/LOCK — / For RHD Models ADJUSTMENT .................................................... 36
(With Power Window) ............................................. 12 SURFACE HEIGHT ADJUSTMENT .................... 36
Wiring Diagram — D/LOCK — / For LHD Models Removal and Installation of Trunk Lid Assembly ... 37 L
(Without Power Window) ........................................ 13 Removal and Installation of Trunk Lid Weatherstrip... 37
Wiring Diagram — D/LOCK — / For RHD models TRUNK LID OPENER ............................................... 38
(Without Power Window) ........................................ 14 Component Parts and Harness Connector Location... 38 M
Terminals and Reference Value of BCM ................ 15 Wiring Diagram — TLID — / For LHD Models ........ 39
Trouble Diagnosis Chart by Symptom .................... 16 Wiring Diagram — TLID — / For RHD Models ....... 40
REMOTE KEYLESS ENTRY SYSTEM .................... 17 Terminal and Reference Value for BCM ................. 41
Component Parts and Harness Connector Location... 17 Trouble Diagnosis Chart by Symptom .................... 41
Wiring Diagram — KEYLES— / For LHD Models... 19 NATS(NISSAN ANTI-THEFT SYSTEM) ................... 42
Wiring Diagram — KEYLES — / For RHD Models... 20 Component Parts and Harness Connector Location... 42
Terminals and Reference Value for BCM ............... 21 ECM Re-communicating Function .......................... 42
Trouble Diagnosis Symptom Chart ........................ 23 Wiring Diagram — NATS — ................................... 44
DOOR ....................................................................... 25 Terminals and Reference Value for BCM ............... 45
Fitting Adjustment .................................................. 25 Work Flow ............................................................... 46
FRONT DOOR .................................................... 25 Trouble Diagnoses ................................................. 47
REAR DOOR ...................................................... 26 SYMPTOM MATRIX CHART 1 ............................ 47
STRIKER ADJUSTMENT ................................... 26 SYMPTOM MATRIX CHART 2 ............................ 47
Front Door Weatherstrip ......................................... 26 How to Replace NATS Antenna Amp. .................... 48
Rear Door Weatherstrip ......................................... 27
BL
HOOD PFP:F5100
PIIB6508E
PIIB5794E
A : 20 mm (0.79 in) E
B : 6.8 mm (0.268 in)
BL
L
PIIB2528J
PIIB6509E
PIIB6515E
G
1. Radiator core support upper 2. Radiator core support lower 3. Radiator core support lower stay
4. Radiator core support side stay 5. Air guide H
BL
PIIB2801J
1. Front fender
BL
PIIB8554E
Fusible link
40A J (For LHD models) or
1. Fuse block (J/B) 2. 3. BCM M65, M66, M67
40A G (For RHD models)
Wiring Diagram — D/LOCK — / For LHD Models (With Power Window) GIS000WK
BL
TIWB0879E
Wiring Diagram — D/LOCK — / For RHD Models (With Power Window) GIS001QV
TIWT1858E
Wiring Diagram — D/LOCK — / For LHD Models (Without Power Window) GIS000WL
BL
TIWB0880E
Wiring Diagram — D/LOCK — / For RHD models (Without Power Window) GIS001QW
TIWT1859E
A
Signal Voltage (V)
Terminal Wire color Item Condition
input/output (Approx.)
GR*1 ON (Open) 0
13 Rear door switch RH signal Input Rear door RH
Y*2 OFF (Close) Battery voltage D
Inserted Battery voltage
37 R Key switch signal Input Key
Removed 0
E
39 L CAN-H Input/output — —
40 P CAN-L Input/output — —
LG*1 BL
57 Power source (Fuse) Input — Battery voltage
Y*2
Door lock actuator Door lock and unlock switch
65 SB Output 0 → Battery voltage → 0 J
LOCK output signal (Free → Lock)
Door lock actuator Door lock and unlock switch
66 G Output 0 → Battery voltage → 0
UNLOCK output signal (Free → Unlock)
67 B Ground — — 0 K
70 Y Power source (Fusible link) Input — Battery voltage
*1
: For LHD models L
*2
: For RHD models
Make sure other systems using the signal of the following systems operate normally.
Symptom Diagnoses service procedure
1. Check BCM power supply and ground circuit
2. Check door lock and unlock switch
All door lock actuator does not operate
3. Check door lock actuator output signal
4. Replace BCM
1. Check key switch
Key reminder door system does not operate properly. 2. Check door switch
3. Replace BCM
1. Check door lock and unlock switch
Power door lock does not operate with door lock and unlock switch.
2. Replace BCM
Specific door lock actuator does not operate. Check door lock actuator circuit
BL
PIIB8555E
M
a: Fusible link
a: Ignition relay
40A J (For LHD models) or
1. Fuse block (J/B) 2. 3. b: Fuse 15A 61
40A G (For RHD models)
c: Fuse 20A 62
b: Horn relay
4. BCM M65, M66, M67 5. Front door switch (driver side) B34 6. Rear door switch (LH) B71
Trunk lid lock assembly B66 Back door lock assembly D111
7. 8. 9. Key switch M24
(sedan) (hatchback)
PIIB8556E
BL
TIWB1141E
TIWT1860E
A
Termi- Wire Signal Input/ Voltage (V)
Item Condition
nal color Output (Approx.)
Ignition switch ACC power
Ignition switch (ACC or ON B
11 L supply Input Battery voltage
position)
(ACC or ON)
Front door ON (Open) 0
SB*1 Front door switch C
12 Input (Passenger
BR*2 (Passenger side) signal OFF (Close) Battery voltage
side)
GR*1 ON (Open) 0
13 Rear door switch RH signal Input Rear door RH D
Y*2 OFF (Close) Battery voltage
Remote keyless entry
18 V — — 0
receiver ground
E
OCC3881D G
H
Waiting
BL
OCC3879D
Remote keyless entry
20 G Input
receiver signal
K
OCC3880D
*2
: For RHD models
*3
: sedan
*4
: hatch back
A
NOTE:
● Make sure other systems using the signal of the following systems operate normally.
● Always check key fob battery before replacing key fob.
B
Symptom Diagnoses/service procedure
1. Check key switch.
2. Check key fob battery and function. C
3. Check remote keyless entry receiver.
All function of remote keyless entry system do not operate. 4. Refer to ID Code Entry Procedure.
D
NOTE:
If the result of key fob function check with CONSULT-II is OK, key fob
is not malfunctioning.
E
5. Replace BCM.
1. Check key fob battery and function.
2. Check key switch.
F
3. Check door switch.
4. Check ACC switch.
The new ID of key fob cannot be entered. G
5. Replace key fob. Refer to ID Code Entry Procedure.
NOTE:
If the result of key fob function check with CONSULT-II is OK, key fob
is not malfunctioning. H
6. Replace BCM.
1. Check key fob function. (Lock)
2. Replace key fob. Refer to ID Code Entry Procedure.
BL
NOTE:
Door lock does not function with key fob.
If the result of key fob function check with CONSULT-II is OK, key fob
(Power door lock system is “OK”.)
is not malfunctioning. J
3. Check door switch.
4. Replace BCM.
K
1. Check key fob function. (Unlock)
2. Replace key fob. Refer to ID Code Entry Procedure.
Door unlock does not function with key fob NOTE:
(Power door lock system is “ON”)
L
If the result of key fob function check with CONSULT-II is OK, key fob
is not malfunctioning.
3. Replace BCM.
M
1. Check hazard reminder mode.*
*: Hazard reminder mode can be changed.
Hazard reminder does not activate properly when pressing First check the hazard reminder setting.
lock or unlock button of key fob.
2. Check hazard function.
3. Replace BCM.
Map lamp and ignition keyhole illumination operation does 1. Check map lamp and ignition keyhole illumination operation.
not activate properly. 2. Replace BCM.
DOOR PFP:80100
A
Fitting Adjustment GIS0009T
BL
PIIB6516E
FRONT DOOR
Longitudinal Clearance and Surface Height Adjustment at Front End
Accessing from inside the fender, loosen the hinge mounting bolts. Raise the front door at rear end to adjust.
Surface Height Adjustment
Loosen the front door mounting bolts, and adjust the surface height difference of fender and front door accord-
ing to the fitting standard dimension, by front door.
REAR DOOR
Longitudinal Clearance and Surface Height Adjustment at Front End
1. Remove the center pillar upper garnish and center pillar lower garnish.
2. Accessing from inside the vehicle, loosen the mounting nuts. Open the rear door, and raise the rear door
at rear end to adjust.
Surface Height Adjustment
Loosen the front door striker mounting bolts and rear door mounting bolts, and adjust the surface height differ-
ence of front door and rear door according to the fitting standard dimension, by front door and rear door.
STRIKER ADJUSTMENT
Adjust the striker so that it becomes parallel with the lock insertion
direction.
:16.7 N·m (1.7 kg-m, 12 ft-lb)
PIIB2804J
PIIB2868J
PIIB3607J
BL
PIIB6523E
G
PIIB6530E
PIIB2884J
PIIB2891J
BL
PIIB8557E
Fusible link
1. Fuse block (J/B) 2. 40A J (For LHD models) or 3. BCM M65, M66, M67
40A G (For RHD models)
Back door lock assembly (opener Front door lock actuator (driver side)
4. Back door opener switch D108 5. 6.
actuator) D111 D9
BL
TIWT1861E
TIWT1862E
A
Termi- Wire Signal input/ Voltage (V)
Item Condition
nal color output (Approx.)
LG *1 E
57 *2
Power source (Fuse) Input — Battery voltage
Y
67 B Ground — — 0
F
Power source (Fusible
70 Y Input — Battery voltage
link)
*1: For LHD models
*2:
G
For RHD models
*3: While driver side door unlocked
PIIB3769J
Portion Clearance
Rear fender and trunk lid A-A 3.0 - 5.0 mm
Rear combination lamp and trunk lid B-B 2.8 - 6.2 mm
Rear bumper fascia and trunk lid C-C 4.8 - 9.2 mm
SURFACE HEIGHT ADJUSTMENT
1. Loosen the striker mounting bolts. Raise the striker to the top position, and temporarily tighten the upper
mounting bolt at the position.
2. Close the trunk lid lightly and adjust the surface height, then open the trunk lid, finally, tighten the striker
mounting bolts to the specified torque.
PIIB3770J
BL
PIIB3775J
PIIB8558E
Fusible link
1. Fuse block (J/B) 2. 40A J (For LHD models) or 3. BCM M65, M66, M67
40A G (For RHD models)
Trunk lid lock assembly (opener Front door lock actuator (driver side)
4. Trunk lid opener switch B61 5. 6.
actuator) B66 D9
BL
TIWT1863E
TIWT1864E
A
Wire Signal input/ Voltage (V)
Terminal Item Condition
color output (Approx.)
LG *1 E
57 *2
Power source (Fuse) Input — Battery voltage
Y
67 B Ground — — 0
F
Power source (Fusible
70 Y Input — Battery voltage
link)
*1: For LHD models
*2:
G
For RHD models
*3: While driver side door unlocked
PIIB8559E
Fusible link
1. Fuse block (J/B) 2. 40A J (For LHD models) or 3. BCM M65, M67
40A G (For RHD models)
4. IPDM E/R (Fuse) 20A 62 5. IPDM E/R 6. NATS antenna amp. M26
7. Combination meter M34 8. Security indicator lamp M34 9. ECM E16
Performing following procedure can automatically perform re-communication of ECM and BCM or Intelligent
Key unit, but only when the ECM has been replaced with a new one (*1).
*1: New one means a virgin ECM which has never been energized on-board.
(In this step, initialization procedure by CONSULT-II is not necessary)
NOTE:
● When registering new Key IDs or replacing the ECM other than brand new, refer to CONSULT-II
Operation Manual NATS.
● If multiple keys are attached to the key holder, separate them before work.
● Distinguish keys with unregistered key ID from those with registered ID.
1. Install ECM.
2. Use a registered key (*2), turn ignition switch to “ON”. A
*2: To perform this step, use the key (except for card plate key) that has been used before to perform ECM
replacement.
3. Press and hold ignition switch in “ON” position for at least 5 seconds. B
4. Turn ignition switch to “OFF”.
5. Start engine.
If engine can be started, procedure is completed. C
If engine cannot be started, refer to CONSULT-II Operation Manual NATS and initialize control unit.
BL
TIWT1865E
A
Signal Measuring condition
Wire Voltage [V]
Terminal Signal name input/ Ignition
Color Operation or condition (Approx.)
output switch B
Right after turn ignition
When turn ignition switch
21 P NATS antenna amp. Output ON switch ON, pointer of
ON.
tester should move.
C
Goes OFF → illumi-
Security indicator out-
23 R Output OFF nates (Every 2.4 sec- Battery voltage → 0
put
onds)
D
Right after turn ignition
When turn ignition switch
25 LG NATS antenna amp. Input/Output ON switch ON, pointer of
ON.
tester should move.
E
O*1 Ignition power supply Ignition switch ON or
38 Input ON Battery voltage
W*2 (ON or START) START position.
39 L CAN-H — — — —
F
40 P CAN-L — — — —
LG*1
57 Power source (Fuse) Input OFF — Battery voltage
Y*2 G
67 B Ground — ON — 0
Power source (Fusible
70 Y Input OFF — Battery voltage H
link)
*1:
For LHD models
*2
: For RHD models
BL
SEL024X
● *: When NATS detects trouble, the security indicator lights up while ignition key is in the “ON” position.
L
SYMPTOM MATRIX CHART 2
Non self-diagnosis related item
SYSTEM M
SYMPTOM
(Malfunctioning part or mode)
Security indictor.
Security indicator does not light up.* Open circuit between Fuse and BCM
BCM
*: CONSULT-II self-diagnostic results display screen “no malfunction is detected”.
NOTE:
● If NATS antenna amp. is not installed correctly, NATS sys-
tem will not operate properly and SELF-DIAG RESULTS on
CONSULT-II screen will show “LOCK MODE” or “CHAIN OF
IMMU-KEY”.
● Initialization is not necessary only when NATS antenna
amp. is replaced with a new one.
PIIB6539E
DESCRIPTION
● All dimensions indicated in the figures are actual. B
● When using a tracking gauge, adjust both pointers to equal length. Then check the pointers and gauge
itself to make sure there is no free play.
● When a measuring tape is used, check to be sure there is no elongation, twisting or bending. C
● Measurements should be taken at the center of the mounting holes.
● An asterisk (*) following the value at the measuring point indicates that the measuring point on the other
side is symmetrically the same value. D
● The coordinates of the measurement points are the distances measured from the standard line of ″X″, ″Y″
and ″Z″.
E
BL
PIIA0104E J
ENGINE COMPARTMENT
Measurement
SIIA2496E
Measurement Points
A
BL
SIIA2497E
UNDERBODY (SEDAN)
Measurement
SIIA2498E
Measurement Points
A
BL
SIIA2499E
UNDERBODY (H/B)
Measurement
SIIA2565E
Measurement Points
A
BL
SIIA2566E
SIIA2500E
Measurement Points
A
BL
SIIA2501E
SIIA2567E
Measurement Points
A
BL
SIIA2568E
SIIA2502E
Measurement Points
A
BL
SIIA2503E
SIIA2569E
Measurement Points
A
BL
SIIA2570E