Professional Documents
Culture Documents
TECHNICAL REPORT
King Abdullah International Gardens
Date: 2/28/2024 Document Number: SA-13162-SF
Revision: Rev0 Status: IFR
Author: Bin Ghelaita, Amna Author email: Binghelaita.amna@hilti.com
TABLE OF CONTENTS
1. Introduction ................................................................................................................................................. 2
1.1. Project: project ................................................................................................................................... 2
1.2. Customer ........................................................................................................................................... 2
1.3. Basic assumptions ............................................................................................................................. 2
2. Standards, reports, and design criteria ...................................................................................................... 3
2.1. States of design ................................................................................................................................. 3
2.2. Reference codes and standards ........................................................................................................ 3
2.3. General notes about calculations ...................................................................................................... 3
2.4. Units ................................................................................................................................................... 3
2.5. Software ............................................................................................................................................. 4
3. Product information .................................................................................................................................... 5
3.1. Used Hilti portfolio.............................................................................................................................. 5
3.2. Installation products ........................................................................................................................... 5
3.3. Anchors .............................................................................................................................................. 5
3.4. Product assumptions ......................................................................................................................... 5
4. Design input from the customer ................................................................................................................. 6
4.1. Input documents from the customer .................................................................................................. 6
4.2. Assumptions from Hilti ....................................................................................................................... 6
4.3. Loads ................................................................................................................................................. 6
4.3.1. Seismic Loads ............................................................................................................................... 6
4.3.2. Wind/Snow/Sand Loads ................................................................................................................ 6
4.3.3. Load cases .................................................................................................................................... 7
5. Summary of calculations ............................................................................................................................ 7
6. Design solutions and verifications ............................................................................................................ 10
7. Special Terms and Conditions of HILTI (“Hilti”) for Technical advice ..................................................... 15
8. Appendices ............................................................................................................................................... 16
8.1. Appendix 01 – Engineering Input Checklist/ Client Input ................................................................ 17
8.2. Appendix 02 – PROFIS Design reports ........................................................................................... 18
The company receiving this design package is solely responsible for confirming, reviewing and approving the adequacy and accuracy of all
information contained herein; and for verifying that the proposed solution is suitable for the intended applications.
1 / 18
Technical report
King Abdullah International Gardens
MO
1. Introduction
The Scope of this document is to provide proof of the structural integrity of designed supports according to the
Agreed Framework. It is important to notice that not all individual supports are calculated, but calculations are
done according to a common agreement.
This document was done according to the relevant regulations and approvals stated later in the document.
Chapter 7. “Appendices” forms an integral part of this documentation as amended from time to time as
indicated by the revision status in this document.
The is King Abdullah International Gardens composed of roof supports and Steel Structure supports which will
be grouped as follow for our framework definition:
• CDP, CWP, and Duct supports on the roof.
• Drain supports on the steel structure.
1.2. Customer
Name: Zaid Al Hussain Group
Contact person: N/A
Contact details \ Address information N/A
Hilti provides technical advice on their products, but load inputs and calculations should be verified and
checked by the customer project designer. It is also assumed that guidance in Instruction For Use is kept for
all products mentioned in present document and there is no need for capacity reduction from abnormal use of
products.
The company receiving this design package is solely responsible for confirming, reviewing and approving the adequacy and accuracy of all
information contained herein; and for verifying that the proposed solution is suitable for the intended applications.
2 / 18
Technical report
King Abdullah International Gardens
MO
Local Stress and deformation of members at places where the load is manually entered are not considered.
All connectors and strut connection interfaces provided by Hilti are developed considering local stress and
deformation in accordance with the Eurocode.
2.4. Units
The S.I (system international) metric system was used. The following table shows the unit associated with the
items of major interest for structural analysis purposes.
Item Unit
Length mm
Angles o (degree)
Forces kN
Moments kNm
The company receiving this design package is solely responsible for confirming, reviewing and approving the adequacy and accuracy of all
information contained herein; and for verifying that the proposed solution is suitable for the intended applications.
3 / 18
Technical report
King Abdullah International Gardens
MO
2.5. Software
The following software has been used in structural design.
Software Version
PROFIS Modular Supports Engineering 1746
Hilti PROFIS Installation 2.23.0
Hilti PROFIS Engineering 3.0.43
Hilti PROFIS Anchor 2.8.2
Hilti PROFIS Anchor Channel 1.7.4
Dlubal RSTAB 8.24
Fig 3: Software
The company receiving this design package is solely responsible for confirming, reviewing and approving the adequacy and accuracy of all
information contained herein; and for verifying that the proposed solution is suitable for the intended applications.
4 / 18
Technical report
King Abdullah International Gardens
MO
3. Product information
The values used in these calculations are based on the following documentation provided by Hilti.
Hilti has developed Internal Guidelines for definition essential characteristics and evaluation of the
performance of its Installation Products. Technical data has been provided from testing, analytical calculations
or finite element analysis or combination of these.
All used products are manufactured under a qualified Quality Management System in according with the
requirements of ISO 9001 and ISO 14001 standard. Hilti is taking full responsibility for its product quality from
development to end of the lifecycle.
3.3. Anchors
For all those anchors holding a European Technical Assessment (ETA) the technical data used in this report
is based and in accordance with the information given in the respective ETA. Additional Hilti technical data,
supplementing the ETA technical data, may be available, in which case, it will be clearly noted in calculation
reports.
For all those anchors not holding an ETA, the technical data used in this report is based on numerous tests
and evaluation criteria according to the current state-of-the-art and/or the relevant European applicable
regulations for the assessment of fasteners, which is the basis for obtaining an ETA.
The company receiving this design package is solely responsible for confirming, reviewing and approving the adequacy and accuracy of all
information contained herein; and for verifying that the proposed solution is suitable for the intended applications.
5 / 18
Technical report
King Abdullah International Gardens
MO
Additional Inputs:
• 2.2% seismic load
• 200% safety factor
• 3m spacing for CWP and 1.5m spacing for CDP
• 2.4m spacing for ducts
• Hot-dipped Galvanised Steel Supports
4.2. Assumptions from Hilti
Default values for deflections used are L/200 for beams and L/150 for cantilevers.
Load calculations as per summary sheet in section 5 of the report.
Duct weigths as per SMACNA.
Rubber inlay provided by customer.
Pipe clamp thickness = pipe OD + insulation.
Fixed point assumptions:
• Steel beam profile HE B 180
• Bending arm: 5m
• Tempreatures from 4.4 to 49°C
Duct fixations not included.
Only on drain riser considered.
4.3. Loads
Load actions are classified in EC1990 by their variation in time as permanent actions (G), variable actions (Q)
and accidental actions (A). For simplicity, we refer to all variable loads as Live loads and permanent loads as
Dead loads. For live loads, we use a partial safety factor of 1,5 for ULS. For dead loads, we use a partial safety
factor 1,35. For SLS safety factor is 1,0 for both load cases.
Pipes and ducts represent elements for which variations in time are considered as negligible by EN1990
definitions. Based on that, loads from pipes and ducts are assumed to be dead loads.
The company receiving this design package is solely responsible for confirming, reviewing and approving the adequacy and accuracy of all
information contained herein; and for verifying that the proposed solution is suitable for the intended applications.
6 / 18
Technical report
King Abdullah International Gardens
MO
The structural integrity for each one of the support solutions listed in Fig 4 has been checked. Calculations
have been done in PROFIS Installation, unless specified otherwise.
The calculations show that these solutions meet all requirements as specified by the customer, as well as the
relevant standards and regulations. Therefore, it can be stated that these solutions are safe for use.
The company receiving this design package is solely responsible for confirming, reviewing and approving the adequacy and accuracy of all
information contained herein; and for verifying that the proposed solution is suitable for the intended applications.
7 / 18
Technical report
King Abdullah International Gardens
MO
Summary Sheet
[SA-13162-SA]
CDP Pipes on Roof
Weight
Total
Pipe of Pipe Load Design
Type of Weight Insulation Total Support Safety Seismic Seismic Wind
Nominal Filled of Load of
pipe of Weight Weight spacing factor Factor Load load
size With pipe pipe
Valves
Water
mm kg/m kg/m kg/m kg/m m kN % kN % kn kN
CHW 50 0 7.5 0.74 8.24 3 0.25 200% 0.49 2.2% 0.01 0.76
CHW + GV 50 1.9 7.5 0.74 10.14 3 0.30 200% 0.61 2.2% 0.01 0.76
CHW 65 0 11.7 0.85 12.55 3 0.38 200% 0.75 2.2% 0.01 0.85
CHW + BFV 65 5.6 7.5 0.85 13.95 3 0.42 200% 0.84 2.2% 0.01 0.85
CHW 80 0 15.9 0.98 16.88 3 0.51 200% 1.01 2.2% 0.01 0.96
CHW 100 0 24.2 1.20 25.40 3 0.76 200% 1.52 2.2% 0.02 1.14
Drain to Steel
Weight of
Pipe
Type of pipe filled Support Safety Design Seismic Seismic Wind
Nominal
pipe with spacing factor Load Factor Load load
size
water
# mm kg/m m % kN (z-dir) % kN kN
DRAIN 110 24.2 3 200% 0.29 2.2% 0.01 0.79
DRAIN FP 110 24.2 6.9 200% 0.67 2.2% 0.01 1.82
The company receiving this design package is solely responsible for confirming, reviewing and approving the adequacy and accuracy of all
information contained herein; and for verifying that the proposed solution is suitable for the intended applications.
8 / 18
Technical report
King Abdullah International Gardens
MO
Ducts on Roof
Safety Factor
Spacing (m)
Size (mm)
Load (kN)
2/5P (kN)
1/5P (kN)
W (mm)
D (mm)
800x800 800 800 33.67 12.6 46.27 2.4 200% 2.22 0.89 0.44 2.20% 0.02 4.44
600x600 600 600 19.38 9.72 29.10 2.4 200% 1.40 0.56 0.28 2.20% 0.02 3.33
550x500 550 500 16.96 8.64 25.60 2.4 200% 1.23 0.49 0.25 2.20% 0.01 2.77
500x500 500 500 16.17 8.28 24.45 2.4 200% 1.17 0.47 0.23 2.20% 0.01 2.77
500x250 500 250 12.13 6.48 18.61 2.4 200% 0.89 0.36 0.18 2.20% 0.01 1.39
400x400 400 400 10.96 6.84 17.80 2.4 200% 0.85 0.34 0.17 2.20% 0.01 2.22
400x350 400 350 10.29 6.48 16.77 2.4 200% 0.81 0.32 0.16 2.20% 0.01 1.94
300x200 300 200 5.63 4.68 10.31 2.4 200% 0.49 0.20 0.10 2.20% 0.01 1.11
The company receiving this design package is solely responsible for confirming, reviewing and approving the adequacy and accuracy of all
information contained herein; and for verifying that the proposed solution is suitable for the intended applications.
9 / 18
Technical report
King Abdullah International Gardens
MO
CWP_GV Dia 50
Double
CWP_BFV Dia 50
Double
The company receiving this design package is solely responsible for confirming, reviewing and approving the adequacy and accuracy of all
information contained herein; and for verifying that the proposed solution is suitable for the intended applications.
10 / 18
Technical report
King Abdullah International Gardens
MO
DUCT 300x200 H
300
DUCT 400x350 H
300
The company receiving this design package is solely responsible for confirming, reviewing and approving the adequacy and accuracy of all
information contained herein; and for verifying that the proposed solution is suitable for the intended applications.
11 / 18
Technical report
King Abdullah International Gardens
MO
DUCT 400x400 H
2000
DUCT 500x250 H
300
DUCT 500x500 H
2200
DUCT 550x500 H
650
The company receiving this design package is solely responsible for confirming, reviewing and approving the adequacy and accuracy of all
information contained herein; and for verifying that the proposed solution is suitable for the intended applications.
12 / 18
Technical report
King Abdullah International Gardens
MO
DUCT 550x500 H
1675
DUCT 600x600 H
300
DUCT 800x800 H
700
DUCT 800x800 H
2200
The company receiving this design package is solely responsible for confirming, reviewing and approving the adequacy and accuracy of all
information contained herein; and for verifying that the proposed solution is suitable for the intended applications.
13 / 18
Technical report
King Abdullah International Gardens
MO
DRAIN FP
The company receiving this design package is solely responsible for confirming, reviewing and approving the adequacy and accuracy of all
information contained herein; and for verifying that the proposed solution is suitable for the intended applications.
14 / 18
Technical report
King Abdullah International Gardens
MO
2. Hilti generally provides the technical advice based on technical and legal provisions applicable at Hilti’s
place of establishment.
3. It is the Customer's responsibility to inform Hilti of all project or object related marginal conditions
relevant for Hilti's technical advice, and to check that the technical assumptions by Hilti are correct and
complete and immediately inform Hilti of any misalignments in text form. Hilti is not obliged to verify or check
the project and/or object related framework conditions reported by the Customer (e.g. to ensure compliance
with the actual on-site conditions, legal requirements or plausibility). This also applies when Hilti has inspected
or had access to an object, design documents, or similar technical information on the project or object. Object
or project related framework conditions shall be deemed to be the basis for Hilti's technical advice only when
Hilti has expressly confirmed this; for example, through the reproduction of, or reference to, documents
provided by Hilti in the technical consultation or separate written confirmation. It is the Customer's responsibility
to arrange and pay for the technical advice provided by Hilti.
4. The output is prepared based on the technical information that the Customer provides to Hilti, for Hilti
to provide a non-binding suggestion over the product to be used by the Customer in its project. Insofar as
Hilti's technical advice is based on object or project related framework conditions, it is the Customer's sole
responsibility to ensure and verify this advice is under the actual circumstances and correspond to the specific
application intended by the Customer. Even slight deviations in design or slight differences between the actual
conditions and those specified by the Customer to Hilti, which Hilti has used for providing the technical advice,
will require a technical re-evaluation and re-calculation, which shall be the Customer's sole responsibility to
arrange with Hilti.
5. Designs and calculations are carried out with the relevant Hilti Profis calculation software or R-stab
software, details about the software, its limitations and underlying measurement methods can be obtained
from Hilti. Hilti designs and calculations are based on codes, general design standards, and Hilti-published
data current as of their creation date. For Hilti component and connection design see published technical data,
including material and cross-section properties, allowable load values, factors of safety, methods of
calculation, and limiting factors.
6. When providing designs and calculations, Hilti does not consider the following technical requirements:
The company receiving this design package is solely responsible for confirming, reviewing and approving the adequacy and accuracy of all
information contained herein; and for verifying that the proposed solution is suitable for the intended applications.
15 / 18
Technical report
King Abdullah International Gardens
MO
If any of the above technical requirements need to be considered, Customer must specifically inquire with Hilti
whether this is possible. Hilti must agree in writing (typically mentioned in Technical report) to provide a solution
taking the above technical requirements into account, otherwise they are not considered.
7. If the bill of materials contains Hilti anchors, Profis MSE and/or Profis Engineering software is utilized
for the calculation. Load values of the anchors are published in the current Technical Manual.
Technical advice of direct fastening (DX) connections is based on FTM Hilti Fastening technology Manual.
8. In case of modification or additional object or project related framework conditions which require
additional technical advice from Hilti, Hilti may accept to do so at an additional charge to be agreed with the
Customer.
9. The technical advice refers exclusively to products sold by Hilti and it is not transferable to products
from other manufacturers. All technical solutions communicated as part of the technical advice are always
object or project specific and non-transferable. It is therefore the Customers' sole liability to decide whether
to acquire or not the product suggested by Hilti; the Product shall be sold on the sole basis of Hilti’s standard
product warranty.
10. Unless expressly stated or agreed otherwise, performance deadlines and dates in the technical advice
are always non-binding.
11. Technical recommendations made by Hilti to Customers are deemed to be non-binding and for the
only purpose to provide the Customer with an initial indication of technical feasibility of Hilti's products and a
provisional estimation of material costs. The Technical recommendations constitute a conceptual or detailed
design, and must be reviewed and approved by the appropriate and responsible person from the Customer’s
side. In particular regarding conformity with the data in the technical data sheets, technical manuals, operating
instructions and approvals of the respective Hilti products, the applicable laws and regulations, the recognized
engineering standards and the on-site conditions. The technical data sheets, technical manuals, operating
instructions and approvals for Hilti products can be viewed at https://www.hilti.sa/
or ordered from Hilti.
12. Hilti's liability is limited to direct damage caused by intent and gross negligence, so HILTI is not liable
for consequential damages, loss of business, damages or any other variation that impacts the assets of the
Customer or any third party.
13. Personal data, sensitive personal data, databases, and other information that may be considered
protected will be treated in accordance with Hilti data protection policy and in accordance with current
regulations.
14. Additionally, the Customer declares to know and accept the Hilti Terms and Conditions of Sale that
can be consulted in https://www.hilti.sa/content/hilti/META/SA/en/support/legal/index/terms.html
which are understood to be an integral part of this document. In case of contradiction between the Terms and
Conditions of Sale of Hilti and this document, the latter will always prevail.
8. Appendices
The company receiving this design package is solely responsible for confirming, reviewing and approving the adequacy and accuracy of all
information contained herein; and for verifying that the proposed solution is suitable for the intended applications.
16 / 18
Technical report
King Abdullah International Gardens
MO
The company receiving this design package is solely responsible for confirming, reviewing and approving the adequacy and accuracy of all
information contained herein; and for verifying that the proposed solution is suitable for the intended applications.
17 / 18
Technical report
King Abdullah International Gardens
MO
The company receiving this design package is solely responsible for confirming, reviewing and approving the adequacy and accuracy of all
information contained herein; and for verifying that the proposed solution is suitable for the intended applications.
18 / 18
Wind Pressure Design Calculation Project # : SA-13162-SF
Designed by : Amna Bin Ghelaita
Date : 29/2/2024
Exp = D
F= qz G Cf Af (29.4-1.si)
qz = 0.613 Kz Kzt Kd V2 (26.10-1.si)
2
qz = 1356.05 N/m
29/02/2024
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan
Hilti Aktiengesellschaft | Feldkircherstrasse 100 | Postfach 333 | 9494 Schaan
Phone: 1-800-879-8000 | Fax: 1-800-879-8000 | E-Mail: sales@hilti.com FixPoint Calculator Ver. 1.10.0.0
Vertical Bending
Loads are applied only to the fixed-point which is located at the center of the
coordinate system
Calculation basis
Geometry
Length, L m 6.6
Bending arm, B m 5
Total pipe length, Ltotal m 9.1
Actual span, S m 3
Min bending arm, Bmin m 0.97
Expansion, X mm -3.27
Distance, H m 0.15
Position of application Riser
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
PipeFL-9494 Schaan
Copyright (c) Hilti AG 2010,
Pipe
Pipe material
Operating temperature
Maximum temperature °C 49
Installation temperature °C 49
Minimum temperature °C 4.4
Temperature difference, ΔT K -44.6
Sliding element*
Name MT-FPS-SF OC
Item number 2330920
*The friction coefficient is not relevant for the calculation of the riser application.
The dead weights of the pipe shoes are considered for the fixed-point evaluation. The
dead weights of the MRG and MSG sliders are neglected.
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan
Hilti Aktiengesellschaft | Feldkircherstrasse 100 | Postfach 333 | 9494 Schaan
Phone: 1-800-879-8000 | Fax: 1-800-879-8000 | E-Mail: sales@hilti.com FixPoint Calculator Ver. 1.10.0.0
Calculation results
The Hilti fixed-point proposed by this software is designed for axial loads (all fixed-
points) and lateral loads (pipe shoes only). Impacts of any additional loads or any other
directional loads have to be manually checked and verified by the responsible
engineer.
Design loads are evaluated per EN 1993-1-1. The temperature reduction factor is
according EN 1993-1-2.
The software applies load factors according EN 1990 for the calculation of the fixed-
point forces. It uses a simplified, conservative approach:
Load combination Ultimate Limit State (ULS): 1.35∙L1+1.5∙L2+1.0∙L3
L1: Dead load: all gravity loads
L2: Live load: expansion, friction, pressure and spring forces
L3: Seismic load
The software is not verifying any pipe static calculation, but just using a simplified
approach according to Hilti standards.
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan
Expansion Pipe weight Construction weight Fixed-point weight
X [mm] Wpipe [kg] Wconstr. [kg] WFP [kg]
Hilti Aktiengesellschaft | Feldkircherstrasse 100 | Postfach 333 | 9494 Schaan
Phone: 1-800-879-8000 | Fax: 1-800-879-8000 | E-Mail: sales@hilti.com FixPoint Calculator Ver. 1.10.0.0
*
The seismic load value was calculated outside the FixPoint Calculator by the responsible engineer
Formulas used
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan
Hilti Aktiengesellschaft | Feldkircherstrasse 100 | Postfach 333 | 9494 Schaan
Phone: 1-800-879-8000 | Fax: 1-800-879-8000 | E-Mail: sales@hilti.com FixPoint Calculator Ver. 1.10.0.0
Fixed-point solution
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan
Some of the used interaction equations used in the FixPoint Calculator make use of the
variables H and h, which describe the distance of the center of the pipe to the base
material. This is necessary to account for the moment loading that the FixPoint is
exposed to. Within the interaction equation the acting forces are converted into
moments by multiplying with H or h.
H and h are of equal value, whereas h is given in the unit mm and H is given without a
unit.
This difference exists due to the different calculatory approaches used in different
interaction equations.
In some cases, a resistance value is given as -99. This indicates that the respective
load direction is not decisive for the failure of the connection.
Utilization 79.85 %
Interaction - Anchors
Utilization 21.19 %
Interaction - Anchors
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan
Hilti Aktiengesellschaft | Feldkircherstrasse 100 | Postfach 333 | 9494 Schaan
Phone: 1-800-879-8000 | Fax: 1-800-879-8000 | E-Mail: sales@hilti.com FixPoint Calculator Ver. 1.10.0.0
Interaction - Anchors
Utilization 21.11 %
Interaction - Anchors
Utilization 21.19 %
Part list
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan
Hilti Aktiengesellschaft | Feldkircherstrasse 100 | Postfach 333 | 9494 Schaan
Phone: 1-800-879-8000 | Fax: 1-800-879-8000 | E-Mail: sales@hilti.com FixPoint Calculator Ver. 1.10.0.0
Any and all information and data contained in the Software concern solely the use of
Hilti products and are based on the principles, formulas and security regulations in
accordance with Hilti's technical directions and operating, mounting and assembly
instructions, etc., that must be strictly complied with by the user. All figures contained
therein are average figures, and therefore use-specific tests are to be conducted prior
to using the relevant Hilti product. The results of the calculations carried out by means
of the Software are based essentially on the data you put in. Therefore, you bear the
sole responsibility for the absence of errors, the completeness and the relevance of the
data to be put in by you. Moreover, you bear sole responsibility for having the results
of the calculation checked and cleared by an expert, particularly with regard to
compliance with applicable norms and permits, prior to using them for your specific
facility. The Software serves only as an aid to interpret norms and permits without any
guarantee as to the absence of errors, the correctness and the relevance of the results
or suitability for a specific application.
Hilti will not be liable for consequences, such as the recovery of lost or damaged data
or programs, arising from a culpable breach of duty by you.
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan
CDP Dia 25 Single H 150
Project: SA-13162-SF
Submitted by:
Date: 28/02/2024
Table of content
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 2 / 23
Version: 1.13.1
Support Details
Modular Support Spacing [mm] Undefined
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 3 / 23
Version: 1.13.1
Concrete
1.2 Nodes
X Y Z
No. No. Connector name Connector variant
[mm] [mm] [mm]
1 1 0.00 0.00 0.00 MT-BR-30 300 OC MT-BR-30 300 OC (C)
1.3 Members
Spring Constants
Releases
Member Translational Rotational
No. Cu,x Cu,y Cu,z Cφx Cφy Cφz
Ux Uy Uz φx φy φz
[kN/m] [kN/m] [kN/m] [kNm/Rad] [kNm/Rad] [kNm/Rad]
1.6 Gliders
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 4 / 23
Version: 1.13.1
2 Part list
2.1 Members
Quantity Weight
Position Item Number Description
[-] [kg]
Quantity Weight
Position Item Number Description
[-] [kg]
2.4 Other
Quantity Weight
Position Item Number Description
[-] [kg]
2 290029 Screw anchor HUS-HR 8x55 5/-/- 2 0.07
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 5 / 23
Version: 1.13.1
3 Load Types
3. Loads
Custom loads
Position Fx Fy Fz Mx My Mz
Load No. Load Type Members
[mm] [kN] [kN] [kN] [kNm] [kNm] [kNm]
1 Design 1 187.50 0.00 0.00 -0.09 0.00 0.00 0.00
2 Wind (+x) 1 187.50 0.01 0.00 0.00 0.00 0.00 0.00
3 Wind (-x) 1 187.50 -0.01 -0.00 -0.00 -0.00 -0.00 -0.00
4 Wind (+y) 1 187.50 0.00 0.01 0.00 0.00 0.00 0.00
5 Wind (-y) 1 187.50 -0.00 -0.01 -0.00 -0.00 -0.00 -0.00
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 6 / 23
Version: 1.13.1
Start End
Fx Fy Fz Mx My Mz
Load No. Load Type Members Position Position
[kN/m] [kN/m] [kN/m] [kNm/m] [kNm/m] [kNm/m]
[mm] [mm]
6 Self Weight Support 1 0.00 300.00 0.00 0.00 -0.02 0.00 0.00 0.00
7 Design Permanent ☑
8 Wind (+x) Variable ☐
9 Wind (-x) Variable ☐
10 Wind (+y) Variable ☐
11 Wind (-y) Variable ☐
1 Self Weight Support Permanent ☑
☑All loads in these load cases are converted to seismic in +/-X, +/-Y and +/-Z
☐Loads not considered for seismic load conversion
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 7 / 23
Version: 1.13.1
4 Load Combinations
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 8 / 23
Version: 1.13.1
5 Results
5.1.3 Members
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 9 / 23
Version: 1.13.1
5.2 Members
Iω M Wy Wz Wy
[mm⁶] [kg/m] [mm³] [mm³] [mm³]
8522000.00 2.17 -1004.46 -2443.24 -1004.46
5.2.2.1 Overview
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 10 / 23
Version: 1.13.1
*007b-ULS: SW_sup + Wind (-x). Respective Combination Equation: 1.35 * LC1 + 1.50 * LC9
Beam No. 1
*007b-ULS: SW_sup + Wind (-x). Respective Combination Equation: 1.35 * LC1 + 1.50 * LC9
Normal load
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 11 / 23
Version: 1.13.1
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 12 / 23
Version: 1.13.1
Torsion around X
Moment around Y
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 13 / 23
Version: 1.13.1
Moment around Z
Buckling ratio
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 14 / 23
Version: 1.13.1
Criteria
☑Maximum Allowable Deflection (Beam) L/200
☑Maximum Allowable Deflection (Cantilever)L/150
- Maximum Deflection (Absolute) -
☑No Deflection checks calculated for 1.50mm
Overview
Results
Reference
Member Max deflection Utilization
Load Combination number* Governing criteria Length Limit
No. [mm] [%]
[mm]
1 018-SLS Relative (Beam) 300.00 L/200 -0.00 0.00
*018-SLS: SW + Live + Snow + Wind (-y). Respective Combination Equation: 1.00 * LC1 + 1.00 * 0.60 * LC11
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 15 / 23
Version: 1.13.1
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 16 / 23
Version: 1.13.1
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 17 / 23
Version: 1.13.1
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 18 / 23
Version: 1.13.1
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 19 / 23
Version: 1.13.1
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 20 / 23
Version: 1.13.1
5.3 Connectors
5.3.1 Overview
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 21 / 23
Version: 1.13.1
5.4 Bases
5.4.1 Overview
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 22 / 23
Version: 1.13.1
Any and all information and data contained in the Software concern solely the use of Hilti products and based on the principles, formulas and security
regulations in accordance with Hilti's technical directions and operating, mounting and assembly instructions, etc., that must be strictly complied with by
the user. All figures contained therein are average figures, and therefore use-specific tests are to be conducted prior to using the relevant Hilti product.
The results of the calculations carried out by means of the Software are based essentially on the data you put in. Therefore, you bear the sole
responsibility for the absence of errors, the completeness and the relevance of the data to be put in by you. Moreover, you bear sole responsibility for
having the results of the calculation checked and cleared by an expert, particularly with regard to compliance with applicable norms and permits, prior
to using them for your specific facility. The Software servers only as an aid to interpret norms and permits without any guarantee as to the absence of
errors, the correctness and relevance ot the results or suitability for a specific application.
You must take all necessary and reasonable steps to prevent or limit damage caused by the Software. In particular, you must arrange for the regular
backup of programs and, if applicable, carry out the updates of that you are using the current and thus up-to-date version of the Software in each case
by carrying out manual updates via the Hilti Website. Hilti will not be liable for consequences, such as the recovery of lost or damaged data or
programs, arising from a culpable breach of duty by you.
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 23 / 23
CDP Dia 25 Single H 300
Project: SA-13162-SF
Submitted by:
Date: 28/02/2024
Table of content
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 2 / 21
Version: 1.13.1
Support Details
Modular Support Spacing [mm] Undefined
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 3 / 21
Version: 1.13.1
Concrete
1.2 Nodes
X Y Z
No. No. Connector name Connector variant
[mm] [mm] [mm]
1 1 0.00 0.00 0.00 MT-B-T OC MT-B-T OC (C)
1.3 Members
Spring Constants
Releases
Member Translational Rotational
No. Cu,x Cu,y Cu,z Cφx Cφy Cφz
Ux Uy Uz φx φy φz
[kN/m] [kN/m] [kN/m] [kNm/Rad] [kNm/Rad] [kNm/Rad]
1.6 Gliders
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 4 / 21
Version: 1.13.1
2 Part list
2.1 Members
Quantity Weight
Position Item Number Description
[-] [kg]
2 2272092 2-hole Baseplate MT-B-T OC 1 0.56
Quantity Weight
Position Item Number Description
[-] [kg]
2.4 Other
Quantity Weight
Position Item Number Description
[-] [kg]
3 2273256 Hexagon bolt MT-TLB OC 2 0.05
4 2272082 Twist-Lock MT-TL M10 OC 2 0.07
5 2105870 Stud anchor HST3-R M12x115 40/20 2 0.20
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 5 / 21
Version: 1.13.1
3 Load Types
3. Loads
Custom loads
Position Fx Fy Fz Mx My Mz
Load No. Load Type Members
[mm] [kN] [kN] [kN] [kNm] [kNm] [kNm]
1 Design 1 300.00 0.00 0.00 -0.09 0.00 0.00 0.00
2 Wind (+x) 1 300.00 0.01 -0.00 -0.00 -0.00 -0.00 -0.00
3 Wind (-x) 1 300.00 -0.01 -0.00 -0.00 -0.00 -0.00 -0.00
4 Self Weight Support 1 0.00 0.00 0.00 -0.01 0.00 0.00 0.00
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 6 / 21
Version: 1.13.1
Start End
Fx Fy Fz Mx My Mz
Load No. Load Type Members Position Position
[kN/m] [kN/m] [kN/m] [kNm/m] [kNm/m] [kNm/m]
[mm] [mm]
5 Self Weight Support 1 0.00 450.00 0.00 0.00 -0.01 0.00 0.00 0.00
7 Design Permanent ☑
8 Wind (+x) Variable ☐
9 Wind (-x) Variable ☐
1 Self Weight Support Permanent ☑
☑All loads in these load cases are converted to seismic in +/-X, +/-Y and +/-Z
☐Loads not considered for seismic load conversion
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 7 / 21
Version: 1.13.1
4 Load Combinations
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 8 / 21
Version: 1.13.1
5 Results
5.1.3 Members
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 9 / 21
Version: 1.13.1
5.2 Members
Iω M Wy Wz Wy
[mm⁶] [kg/m] [mm³] [mm³] [mm³]
8522000.00 1.49 -1004.46 -2443.24 -1004.46
5.2.2.1 Overview
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 10 / 21
Version: 1.13.1
*007b-ULS: SW_sup + Wind (-x). Respective Combination Equation: 1.35 * LC1 + 1.50 * LC9
Beam No. 1
*007b-ULS: SW_sup + Wind (-x). Respective Combination Equation: 1.35 * LC1 + 1.50 * LC9
Normal load
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 11 / 21
Version: 1.13.1
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 12 / 21
Version: 1.13.1
Torsion around X
Moment around Y
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 13 / 21
Version: 1.13.1
Moment around Z
Buckling ratio
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 14 / 21
Version: 1.13.1
Criteria
☑Maximum Allowable Deflection (Beam) L/200
☑Maximum Allowable Deflection (Cantilever)L/150
- Maximum Deflection (Absolute) -
☑No Deflection checks calculated for 1.50mm
Overview
Results
Reference
Member Max deflection Utilization
Load Combination number* Governing criteria Length Limit
No. [mm] [%]
[mm]
1 016-SLS Relative (Beam) 450.00 L/200 0.04 0.00
*016-SLS: SW + Live + Snow + Wind (-x). Respective Combination Equation: 1.00 * LC1 + 1.00 * 0.60 * LC9
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 15 / 21
Version: 1.13.1
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 16 / 21
Version: 1.13.1
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 17 / 21
Version: 1.13.1
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 18 / 21
Version: 1.13.1
5.3 Connectors
5.3.1 Overview
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 19 / 21
Version: 1.13.1
5.4 Bases
5.4.1 Overview
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 20 / 21
Version: 1.13.1
Any and all information and data contained in the Software concern solely the use of Hilti products and based on the principles, formulas and security
regulations in accordance with Hilti's technical directions and operating, mounting and assembly instructions, etc., that must be strictly complied with by
the user. All figures contained therein are average figures, and therefore use-specific tests are to be conducted prior to using the relevant Hilti product.
The results of the calculations carried out by means of the Software are based essentially on the data you put in. Therefore, you bear the sole
responsibility for the absence of errors, the completeness and the relevance of the data to be put in by you. Moreover, you bear sole responsibility for
having the results of the calculation checked and cleared by an expert, particularly with regard to compliance with applicable norms and permits, prior
to using them for your specific facility. The Software servers only as an aid to interpret norms and permits without any guarantee as to the absence of
errors, the correctness and relevance ot the results or suitability for a specific application.
You must take all necessary and reasonable steps to prevent or limit damage caused by the Software. In particular, you must arrange for the regular
backup of programs and, if applicable, carry out the updates of that you are using the current and thus up-to-date version of the Software in each case
by carrying out manual updates via the Hilti Website. Hilti will not be liable for consequences, such as the recovery of lost or damaged data or
programs, arising from a culpable breach of duty by you.
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 21 / 21
CDP Dia 40 Single H 300
Project: SA-13162-SF
Submitted by:
Date: 28/02/2024
Table of content
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 2 / 21
Version: 1.13.1
Support Details
Modular Support Spacing [mm] Undefined
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 3 / 21
Version: 1.13.1
Concrete
1.2 Nodes
X Y Z
No. No. Connector name Connector variant
[mm] [mm] [mm]
1 1 0.00 0.00 0.00 MT-B-T OC MT-B-T OC (C)
1.3 Members
Spring Constants
Releases
Member Translational Rotational
No. Cu,x Cu,y Cu,z Cφx Cφy Cφz
Ux Uy Uz φx φy φz
[kN/m] [kN/m] [kN/m] [kNm/Rad] [kNm/Rad] [kNm/Rad]
1.6 Gliders
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 4 / 21
Version: 1.13.1
2 Part list
2.1 Members
Quantity Weight
Position Item Number Description
[-] [kg]
2 2272092 2-hole Baseplate MT-B-T OC 1 0.56
Quantity Weight
Position Item Number Description
[-] [kg]
2.4 Other
Quantity Weight
Position Item Number Description
[-] [kg]
3 2273256 Hexagon bolt MT-TLB OC 2 0.05
4 2272082 Twist-Lock MT-TL M10 OC 2 0.07
5 2105870 Stud anchor HST3-R M12x115 40/20 2 0.20
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 5 / 21
Version: 1.13.1
3 Load Types
3. Loads
Custom loads
Position Fx Fy Fz Mx My Mz
Load No. Load Type Members
[mm] [kN] [kN] [kN] [kNm] [kNm] [kNm]
1 Design 1 300.00 0.00 0.00 -0.16 0.00 0.00 0.00
2 Wind (+x) 1 300.00 0.01 -0.00 -0.00 -0.00 -0.00 -0.00
3 Wind (-x) 1 300.00 -0.01 -0.00 -0.00 -0.00 -0.00 -0.00
4 Self Weight Support 1 0.00 0.00 0.00 -0.01 0.00 0.00 0.00
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 6 / 21
Version: 1.13.1
Start End
Fx Fy Fz Mx My Mz
Load No. Load Type Members Position Position
[kN/m] [kN/m] [kN/m] [kNm/m] [kNm/m] [kNm/m]
[mm] [mm]
5 Self Weight Support 1 0.00 465.00 0.00 0.00 -0.01 0.00 0.00 0.00
7 Design Permanent ☑
8 Wind (+x) Variable ☐
9 Wind (-x) Variable ☐
1 Self Weight Support Permanent ☑
☑All loads in these load cases are converted to seismic in +/-X, +/-Y and +/-Z
☐Loads not considered for seismic load conversion
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 7 / 21
Version: 1.13.1
4 Load Combinations
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 8 / 21
Version: 1.13.1
5 Results
5.1.3 Members
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 9 / 21
Version: 1.13.1
5.2 Members
Iω M Wy Wz Wy
[mm⁶] [kg/m] [mm³] [mm³] [mm³]
8522000.00 1.49 -1004.46 -2443.24 -1004.46
5.2.2.1 Overview
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 10 / 21
Version: 1.13.1
*007b-ULS: SW_sup + Wind (-x). Respective Combination Equation: 1.35 * LC1 + 1.50 * LC9
Beam No. 1
*007b-ULS: SW_sup + Wind (-x). Respective Combination Equation: 1.35 * LC1 + 1.50 * LC9
Normal load
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 11 / 21
Version: 1.13.1
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 12 / 21
Version: 1.13.1
Torsion around X
Moment around Y
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 13 / 21
Version: 1.13.1
Moment around Z
Buckling ratio
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 14 / 21
Version: 1.13.1
Criteria
☑Maximum Allowable Deflection (Beam) L/200
☑Maximum Allowable Deflection (Cantilever)L/150
- Maximum Deflection (Absolute) -
☑No Deflection checks calculated for 1.50mm
Overview
Results
Reference
Member Max deflection Utilization
Load Combination number* Governing criteria Length Limit
No. [mm] [%]
[mm]
1 016-SLS Relative (Beam) 465.00 L/200 0.04 0.00
*016-SLS: SW + Live + Snow + Wind (-x). Respective Combination Equation: 1.00 * LC1 + 1.00 * 0.60 * LC9
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 15 / 21
Version: 1.13.1
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 16 / 21
Version: 1.13.1
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 17 / 21
Version: 1.13.1
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 18 / 21
Version: 1.13.1
5.3 Connectors
5.3.1 Overview
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 19 / 21
Version: 1.13.1
5.4 Bases
5.4.1 Overview
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 20 / 21
Version: 1.13.1
Any and all information and data contained in the Software concern solely the use of Hilti products and based on the principles, formulas and security
regulations in accordance with Hilti's technical directions and operating, mounting and assembly instructions, etc., that must be strictly complied with by
the user. All figures contained therein are average figures, and therefore use-specific tests are to be conducted prior to using the relevant Hilti product.
The results of the calculations carried out by means of the Software are based essentially on the data you put in. Therefore, you bear the sole
responsibility for the absence of errors, the completeness and the relevance of the data to be put in by you. Moreover, you bear sole responsibility for
having the results of the calculation checked and cleared by an expert, particularly with regard to compliance with applicable norms and permits, prior
to using them for your specific facility. The Software servers only as an aid to interpret norms and permits without any guarantee as to the absence of
errors, the correctness and relevance ot the results or suitability for a specific application.
You must take all necessary and reasonable steps to prevent or limit damage caused by the Software. In particular, you must arrange for the regular
backup of programs and, if applicable, carry out the updates of that you are using the current and thus up-to-date version of the Software in each case
by carrying out manual updates via the Hilti Website. Hilti will not be liable for consequences, such as the recovery of lost or damaged data or
programs, arising from a culpable breach of duty by you.
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 21 / 21
CWP Dia 50 Double
Project: SA-13162-SF
Submitted by:
Date: 28/02/2024
Table of content
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 2 / 25
Version: 1.13.1
Support Details
Modular Support Spacing [mm] Undefined
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 3 / 25
Version: 1.13.1
Concrete
1.2 Nodes
X Y Z
No. No. Connector name Connector variant
[mm] [mm] [mm]
1 1 0.00 0.00 0.00 MT-B-O2 OC MT-B-O2 OC (C)
2 - 0.00 0.00 350.00 MT-C-LL1 OC MT-C-LL1 OC (C)
3 - 615.00 0.00 350.00 MT-C-LL1 OC MT-C-LL1 OC (C)
4 2 615.00 0.00 0.00 MT-B-O2 OC MT-B-O2 OC (C)
1.3 Members
Spring Constants
Releases
Member Translational Rotational
No. Cu,x Cu,y Cu,z Cφx Cφy Cφz
Ux Uy Uz φx φy φz
[kN/m] [kN/m] [kN/m] [kNm/Rad] [kNm/Rad] [kNm/Rad]
1.6 Gliders
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 4 / 25
Version: 1.13.1
2 Part list
2.1 Members
Quantity Weight
Position Item Number Description
[-] [kg]
3 2272096 2-hole Baseplate MT-B-O2 OC 2 2.05
Quantity Weight
Position Item Number Description
[-] [kg]
7 2272049 Angle connector MT-C-LL1 OC 2 0.67
2.4 Other
Quantity Weight
Position Item Number Description
[-] [kg]
4 2273256 Hexagon bolt MT-TLB OC 8 0.20
5 2272082 Twist-Lock MT-TL M10 OC 8 0.28
6 2105870 Stud anchor HST3-R M12x115 40/20 4 0.41
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 5 / 25
Version: 1.13.1
3 Load Types
3. Loads
Custom loads
Position Fx Fy Fz Mx My Mz
Load No. Load Type Members
[mm] [kN] [kN] [kN] [kNm] [kNm] [kNm]
1 Design 2 150.00 0.00 0.00 -0.49 0.00 0.00 0.00
2 Design 2 465.00 0.00 0.00 -0.49 0.00 0.00 0.00
3 Wind (+x) 2 465.00 0.76 -0.00 -0.00 -0.00 -0.00 -0.00
4 Wind (-x) 2 465.00 -0.76 -0.00 -0.00 -0.00 -0.00 -0.00
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 6 / 25
Version: 1.13.1
Start End
Fx Fy Fz Mx My Mz
Load No. Load Type Members Position Position
[kN/m] [kN/m] [kN/m] [kNm/m] [kNm/m] [kNm/m]
[mm] [mm]
17 Self Weight Support 1 0.00 350.00 0.00 0.00 -0.02 0.00 0.00 0.00
18 Self Weight Support 2 0.00 615.00 0.00 0.00 -0.02 0.00 0.00 0.00
19 Self Weight Support 3 0.00 350.00 0.00 0.00 -0.02 0.00 0.00 0.00
7 Design Permanent ☑
8 Wind (+x) Variable ☐
9 Wind (-x) Variable ☐
1 Self Weight Support Permanent ☑
☑All loads in these load cases are converted to seismic in +/-X, +/-Y and +/-Z
☐Loads not considered for seismic load conversion
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 7 / 25
Version: 1.13.1
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 8 / 25
Version: 1.13.1
4 Load Combinations
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 10 / 25
Version: 1.13.1
5 Results
5.1.3 Members
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 11 / 25
Version: 1.13.1
5.2 Members
Iω M Wy Wz Wy
[mm⁶] [kg/m] [mm³] [mm³] [mm³]
38410000.00 4.08 -2652.65 -3099.95 -2652.65
5.2.2.1 Overview
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 12 / 25
Version: 1.13.1
*007b-ULS: SW_sup + Wind (-x). Respective Combination Equation: 1.35 * LC1 + 1.50 * LC9
*006b-ULS: SW_sup + Wind (+x). Respective Combination Equation: 1.35 * LC1 + 1.50 * LC8
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 13 / 25
Version: 1.13.1
Beam No. 1
Beam No. 2
Beam No. 3
*007b-ULS: SW_sup + Wind (-x). Respective Combination Equation: 1.35 * LC1 + 1.50 * LC9
*006b-ULS: SW_sup + Wind (+x). Respective Combination Equation: 1.35 * LC1 + 1.50 * LC8
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 14 / 25
Version: 1.13.1
Normal load
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 15 / 25
Version: 1.13.1
Torsion around X
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 16 / 25
Version: 1.13.1
Moment around Y
Moment around Z
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 17 / 25
Version: 1.13.1
Buckling ratio
Criteria
☑Maximum Allowable Deflection (Beam) L/200
☑Maximum Allowable Deflection (Cantilever)L/150
- Maximum Deflection (Absolute) -
☑No Deflection checks calculated for 1.50mm
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 18 / 25
Version: 1.13.1
Overview
Results
Reference
Member Max deflection Utilization
Load Combination number* Governing criteria Length Limit
No. [mm] [%]
[mm]
1 016-SLS Relative (Beam) 350.00 L/200 -0.02 0.00
2 016-SLS Relative (Beam) 615.00 L/200 0.00 0.00
3 016-SLS Relative (Beam) 350.00 L/200 0.00 0.00
*016-SLS: SW + Live + Snow + Wind (-x). Respective Combination Equation: 1.00 * LC1 + 1.00 * 0.60 * LC9
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 19 / 25
Version: 1.13.1
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 20 / 25
Version: 1.13.1
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 21 / 25
Version: 1.13.1
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 22 / 25
Version: 1.13.1
5.3 Connectors
5.3.1 Overview
Connector: MT-C-LL1 OC
Fx Fy Fz Mx My Mz
Connector variant: MT-C-LL1 OC (C)
[kN] [kN] [kN] [kNm] [kNm] [kNm]
Node No. : 3
Local Forces: -0.58 0.00 -0.26 0.00 0.08 0.00
Resistance: 8.20 1.24 8.06 0.03 0.19 0.03
abs(Fx.ed/Fx.rd)+abs(Fy.ed/Fy.rd)+abs(Fz.ed/Fz.rd)+abs(Mx.ed/Mx.rd)+abs(
Equation:
My.ed/My.rd)+abs(Mz.ed/Mz.rd)
Utilization: 50.19 % OK
Governing Load
1.35 * LC1 + 1.50 * LC8
Combination
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 23 / 25
Version: 1.13.1
5.4 Bases
5.4.1 Overview
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 24 / 25
Version: 1.13.1
Any and all information and data contained in the Software concern solely the use of Hilti products and based on the principles, formulas and security
regulations in accordance with Hilti's technical directions and operating, mounting and assembly instructions, etc., that must be strictly complied with by
the user. All figures contained therein are average figures, and therefore use-specific tests are to be conducted prior to using the relevant Hilti product.
The results of the calculations carried out by means of the Software are based essentially on the data you put in. Therefore, you bear the sole
responsibility for the absence of errors, the completeness and the relevance of the data to be put in by you. Moreover, you bear sole responsibility for
having the results of the calculation checked and cleared by an expert, particularly with regard to compliance with applicable norms and permits, prior
to using them for your specific facility. The Software servers only as an aid to interpret norms and permits without any guarantee as to the absence of
errors, the correctness and relevance ot the results or suitability for a specific application.
You must take all necessary and reasonable steps to prevent or limit damage caused by the Software. In particular, you must arrange for the regular
backup of programs and, if applicable, carry out the updates of that you are using the current and thus up-to-date version of the Software in each case
by carrying out manual updates via the Hilti Website. Hilti will not be liable for consequences, such as the recovery of lost or damaged data or
programs, arising from a culpable breach of duty by you.
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 25 / 25
CWP Dia 65-80 Double
Project: SA-13162-SF
Submitted by:
Date: 28/02/2024
Table of content
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 2 / 25
Version: 1.13.1
Support Details
Modular Support Spacing [mm] Undefined
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 3 / 25
Version: 1.13.1
Concrete
1.2 Nodes
X Y Z
No. No. Connector name Connector variant
[mm] [mm] [mm]
1 1 0.00 0.00 0.00 MT-B-O2 OC MT-B-O2 OC (C)
2 - 0.00 0.00 350.00 MT-C-LL1 OC MT-C-LL1 OC (C)
3 - 715.00 0.00 350.00 MT-C-LL1 OC MT-C-LL1 OC (C)
4 2 715.00 0.00 0.00 MT-B-O2 OC MT-B-O2 OC (C)
1.3 Members
Spring Constants
Releases
Member Translational Rotational
No. Cu,x Cu,y Cu,z Cφx Cφy Cφz
Ux Uy Uz φx φy φz
[kN/m] [kN/m] [kN/m] [kNm/Rad] [kNm/Rad] [kNm/Rad]
1.6 Gliders
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 4 / 25
Version: 1.13.1
2 Part list
2.1 Members
Quantity Weight
Position Item Number Description
[-] [kg]
3 2272096 2-hole Baseplate MT-B-O2 OC 2 2.05
Quantity Weight
Position Item Number Description
[-] [kg]
7 2272049 Angle connector MT-C-LL1 OC 2 0.67
2.4 Other
Quantity Weight
Position Item Number Description
[-] [kg]
4 2273256 Hexagon bolt MT-TLB OC 8 0.20
5 2272082 Twist-Lock MT-TL M10 OC 8 0.28
6 2105870 Stud anchor HST3-R M12x115 40/20 4 0.41
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 5 / 25
Version: 1.13.1
3 Load Types
3. Loads
Custom loads
Position Fx Fy Fz Mx My Mz
Load No. Load Type Members
[mm] [kN] [kN] [kN] [kNm] [kNm] [kNm]
1 Design 2 165.00 0.00 0.00 -1.01 0.00 0.00 0.00
2 Design 2 550.00 0.00 0.00 -1.01 0.00 0.00 0.00
3 Wind (+x) 2 550.00 0.96 0.00 0.00 0.00 0.00 0.00
4 Wind (-x) 2 550.00 -0.96 -0.00 -0.00 -0.00 -0.00 -0.00
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 6 / 25
Version: 1.13.1
Start End
Fx Fy Fz Mx My Mz
Load No. Load Type Members Position Position
[kN/m] [kN/m] [kN/m] [kNm/m] [kNm/m] [kNm/m]
[mm] [mm]
17 Self Weight Support 1 0.00 350.00 0.00 0.00 -0.02 0.00 0.00 0.00
18 Self Weight Support 2 0.00 715.00 0.00 0.00 -0.02 0.00 0.00 0.00
19 Self Weight Support 3 0.00 350.00 0.00 0.00 -0.02 0.00 0.00 0.00
7 Design Permanent ☑
8 Wind (+x) Variable ☐
9 Wind (-x) Variable ☐
1 Self Weight Support Permanent ☑
☑All loads in these load cases are converted to seismic in +/-X, +/-Y and +/-Z
☐Loads not considered for seismic load conversion
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 7 / 25
Version: 1.13.1
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 8 / 25
Version: 1.13.1
4 Load Combinations
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 10 / 25
Version: 1.13.1
5 Results
5.1.3 Members
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 11 / 25
Version: 1.13.1
5.2 Members
Iω M Wy Wz Wy
[mm⁶] [kg/m] [mm³] [mm³] [mm³]
38410000.00 4.08 -2652.65 -3099.95 -2652.65
5.2.2.1 Overview
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 12 / 25
Version: 1.13.1
*007b-ULS: SW_sup + Wind (-x). Respective Combination Equation: 1.35 * LC1 + 1.50 * LC9
*004b-ULS: SW_sup + Design Loads. Respective Combination Equation: 1.35 * LC1 + 1.00 * LC7
*006b-ULS: SW_sup + Wind (+x). Respective Combination Equation: 1.35 * LC1 + 1.50 * LC8
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 13 / 25
Version: 1.13.1
Beam No. 1
Beam No. 2
Beam No. 3
*007b-ULS: SW_sup + Wind (-x). Respective Combination Equation: 1.35 * LC1 + 1.50 * LC9
*004b-ULS: SW_sup + Design Loads. Respective Combination Equation: 1.35 * LC1 + 1.00 * LC7
*006b-ULS: SW_sup + Wind (+x). Respective Combination Equation: 1.35 * LC1 + 1.50 * LC8
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 14 / 25
Version: 1.13.1
Normal load
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 15 / 25
Version: 1.13.1
Torsion around X
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 16 / 25
Version: 1.13.1
Moment around Y
Moment around Z
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 17 / 25
Version: 1.13.1
Buckling ratio
Criteria
☑Maximum Allowable Deflection (Beam) L/200
☑Maximum Allowable Deflection (Cantilever)L/150
- Maximum Deflection (Absolute) -
☑No Deflection checks calculated for 1.50mm
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 18 / 25
Version: 1.13.1
Overview
Results
Reference
Member Max deflection Utilization
Load Combination number* Governing criteria Length Limit
No. [mm] [%]
[mm]
1 016-SLS Relative (Beam) 350.00 L/200 -0.06 0.00
2 016-SLS Relative (Beam) 715.00 L/200 0.00 0.00
3 016-SLS Relative (Beam) 350.00 L/200 -0.00 0.00
*016-SLS: SW + Live + Snow + Wind (-x). Respective Combination Equation: 1.00 * LC1 + 1.00 * 0.60 * LC9
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 19 / 25
Version: 1.13.1
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 20 / 25
Version: 1.13.1
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 21 / 25
Version: 1.13.1
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 22 / 25
Version: 1.13.1
5.3 Connectors
5.3.1 Overview
Connector: MT-C-LL1 OC
Fx Fy Fz Mx My Mz
Connector variant: MT-C-LL1 OC (C)
[kN] [kN] [kN] [kNm] [kNm] [kNm]
Node No. : 2
Local Forces: -0.42 0.00 -1.02 0.00 0.10 0.00
Resistance: 8.20 1.24 8.06 0.03 0.19 0.03
abs(Fx.ed/Fx.rd)+abs(Fy.ed/Fy.rd)+abs(Fz.ed/Fz.rd)+abs(Mx.ed/Mx.rd)+abs(
Equation:
My.ed/My.rd)+abs(Mz.ed/Mz.rd)
Utilization: 70.27 % OK
Governing Load
1.35 * LC1 + 1.00 * LC7
Combination
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 23 / 25
Version: 1.13.1
5.4 Bases
5.4.1 Overview
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 24 / 25
Version: 1.13.1
Any and all information and data contained in the Software concern solely the use of Hilti products and based on the principles, formulas and security
regulations in accordance with Hilti's technical directions and operating, mounting and assembly instructions, etc., that must be strictly complied with by
the user. All figures contained therein are average figures, and therefore use-specific tests are to be conducted prior to using the relevant Hilti product.
The results of the calculations carried out by means of the Software are based essentially on the data you put in. Therefore, you bear the sole
responsibility for the absence of errors, the completeness and the relevance of the data to be put in by you. Moreover, you bear sole responsibility for
having the results of the calculation checked and cleared by an expert, particularly with regard to compliance with applicable norms and permits, prior
to using them for your specific facility. The Software servers only as an aid to interpret norms and permits without any guarantee as to the absence of
errors, the correctness and relevance ot the results or suitability for a specific application.
You must take all necessary and reasonable steps to prevent or limit damage caused by the Software. In particular, you must arrange for the regular
backup of programs and, if applicable, carry out the updates of that you are using the current and thus up-to-date version of the Software in each case
by carrying out manual updates via the Hilti Website. Hilti will not be liable for consequences, such as the recovery of lost or damaged data or
programs, arising from a culpable breach of duty by you.
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 25 / 25
CWP Dia 100 Double
Project: SA-13162-SF
Submitted by:
Date: 28/02/2024
Table of content
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 2 / 25
Version: 1.13.1
Support Details
Modular Support Spacing [mm] Undefined
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 3 / 25
Version: 1.13.1
Concrete
1.2 Nodes
X Y Z
No. No. Connector name Connector variant
[mm] [mm] [mm]
1 1 0.00 0.00 0.00 MT-B-O2 OC MT-B-O2 OC (C)
2 - 0.00 0.00 350.00 MT-C-LL1 OC MT-C-LL1 OC (C)
3 - 735.00 0.00 350.00 MT-C-LL1 OC MT-C-LL1 OC (C)
4 2 735.00 0.00 0.00 MT-B-O2 OC MT-B-O2 OC (C)
1.3 Members
Spring Constants
Releases
Member Translational Rotational
No. Cu,x Cu,y Cu,z Cφx Cφy Cφz
Ux Uy Uz φx φy φz
[kN/m] [kN/m] [kN/m] [kNm/Rad] [kNm/Rad] [kNm/Rad]
2 no no no no yes yes - - - - 0.001 0.001
2 no no no no yes yes - - - - 0.001 0.001
1.6 Gliders
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 4 / 25
Version: 1.13.1
2 Part list
2.1 Members
Quantity Weight
Position Item Number Description
[-] [kg]
3 2272096 2-hole Baseplate MT-B-O2 OC 2 2.05
Quantity Weight
Position Item Number Description
[-] [kg]
7 2272049 Angle connector MT-C-LL1 OC 2 0.67
2.4 Other
Quantity Weight
Position Item Number Description
[-] [kg]
4 2273256 Hexagon bolt MT-TLB OC 8 0.20
5 2272082 Twist-Lock MT-TL M10 OC 8 0.28
6 2105870 Stud anchor HST3-R M12x115 40/20 4 0.41
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 5 / 25
Version: 1.13.1
3 Load Types
3. Loads
Custom loads
Position Fx Fy Fz Mx My Mz
Load No. Load Type Members
[mm] [kN] [kN] [kN] [kNm] [kNm] [kNm]
1 Design 2 175.00 0.00 0.00 -1.52 0.00 0.00 0.00
2 Design 2 560.00 0.00 0.00 -1.52 0.00 0.00 0.00
3 Wind (+x) 2 560.00 1.14 -0.00 -0.00 -0.00 -0.00 -0.00
4 Wind (-x) 2 560.00 -1.14 -0.00 -0.00 -0.00 -0.00 -0.00
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 6 / 25
Version: 1.13.1
Start End
Fx Fy Fz Mx My Mz
Load No. Load Type Members Position Position
[kN/m] [kN/m] [kN/m] [kNm/m] [kNm/m] [kNm/m]
[mm] [mm]
17 Self Weight Support 1 0.00 350.00 0.00 0.00 -0.02 0.00 0.00 0.00
18 Self Weight Support 2 0.00 735.00 0.00 0.00 -0.02 0.00 0.00 0.00
19 Self Weight Support 3 0.00 350.00 0.00 0.00 -0.02 0.00 0.00 0.00
7 Design Permanent ☑
8 Wind (+x) Variable ☐
9 Wind (-x) Variable ☐
1 Self Weight Support Permanent ☑
☑All loads in these load cases are converted to seismic in +/-X, +/-Y and +/-Z
☐Loads not considered for seismic load conversion
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 7 / 25
Version: 1.13.1
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 8 / 25
Version: 1.13.1
4 Load Combinations
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 10 / 25
Version: 1.13.1
5 Results
5.1.3 Members
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 11 / 25
Version: 1.13.1
5.2 Members
Iω M Wy Wz Wy
[mm⁶] [kg/m] [mm³] [mm³] [mm³]
38410000.00 4.08 -2652.65 -3099.95 -2652.65
5.2.2.1 Overview
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 12 / 25
Version: 1.13.1
*006b-ULS: SW_sup + Wind (+x). Respective Combination Equation: 1.35 * LC1 + 1.50 * LC8
*004b-ULS: SW_sup + Design Loads. Respective Combination Equation: 1.35 * LC1 + 1.00 * LC7
*007b-ULS: SW_sup + Wind (-x). Respective Combination Equation: 1.35 * LC1 + 1.50 * LC9
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 13 / 25
Version: 1.13.1
Beam No. 1
Beam No. 2
Beam No. 3
*006b-ULS: SW_sup + Wind (+x). Respective Combination Equation: 1.35 * LC1 + 1.50 * LC8
*004b-ULS: SW_sup + Design Loads. Respective Combination Equation: 1.35 * LC1 + 1.00 * LC7
*007b-ULS: SW_sup + Wind (-x). Respective Combination Equation: 1.35 * LC1 + 1.50 * LC9
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 14 / 25
Version: 1.13.1
Normal load
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 15 / 25
Version: 1.13.1
Torsion around X
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 16 / 25
Version: 1.13.1
Moment around Y
Moment around Z
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 17 / 25
Version: 1.13.1
Buckling ratio
Criteria
☑Maximum Allowable Deflection (Beam) L/200
☑Maximum Allowable Deflection (Cantilever)L/150
- Maximum Deflection (Absolute) -
☑No Deflection checks calculated for 1.50mm
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 18 / 25
Version: 1.13.1
Overview
Results
Reference
Member Max deflection Utilization
Load Combination number* Governing criteria Length Limit
No. [mm] [%]
[mm]
1 016-SLS Relative (Beam) 350.00 L/200 -0.01 0.00
2 016-SLS Relative (Beam) 735.00 L/200 -0.00 0.00
3 016-SLS Relative (Beam) 350.00 L/200 -0.00 0.00
*016-SLS: SW + Live + Snow + Wind (-x). Respective Combination Equation: 1.00 * LC1 + 1.00 * 0.60 * LC9
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 19 / 25
Version: 1.13.1
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 20 / 25
Version: 1.13.1
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 21 / 25
Version: 1.13.1
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 22 / 25
Version: 1.13.1
5.3 Connectors
5.3.1 Overview
Connector: MT-C-LL1 OC
Fx Fy Fz Mx My Mz
Connector variant: MT-C-LL1 OC (C)
[kN] [kN] [kN] [kNm] [kNm] [kNm]
Node No. : 2
Local Forces: -0.00 0.00 -1.53 0.00 0.00 0.00
Resistance: 8.06 1.24 8.06 0.03 0.19 0.03
abs(Fx.ed/Fx.rd)+abs(Fy.ed/Fy.rd)+abs(Fz.ed/Fz.rd)+abs(Mx.ed/Mx.rd)+abs(
Equation:
My.ed/My.rd)+abs(Mz.ed/Mz.rd)
Utilization: 18.98 % OK
Governing Load
1.35 * LC1 + 1.00 * LC7
Combination
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 23 / 25
Version: 1.13.1
5.4 Bases
5.4.1 Overview
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 24 / 25
Version: 1.13.1
Any and all information and data contained in the Software concern solely the use of Hilti products and based on the principles, formulas and security
regulations in accordance with Hilti's technical directions and operating, mounting and assembly instructions, etc., that must be strictly complied with by
the user. All figures contained therein are average figures, and therefore use-specific tests are to be conducted prior to using the relevant Hilti product.
The results of the calculations carried out by means of the Software are based essentially on the data you put in. Therefore, you bear the sole
responsibility for the absence of errors, the completeness and the relevance of the data to be put in by you. Moreover, you bear sole responsibility for
having the results of the calculation checked and cleared by an expert, particularly with regard to compliance with applicable norms and permits, prior
to using them for your specific facility. The Software servers only as an aid to interpret norms and permits without any guarantee as to the absence of
errors, the correctness and relevance ot the results or suitability for a specific application.
You must take all necessary and reasonable steps to prevent or limit damage caused by the Software. In particular, you must arrange for the regular
backup of programs and, if applicable, carry out the updates of that you are using the current and thus up-to-date version of the Software in each case
by carrying out manual updates via the Hilti Website. Hilti will not be liable for consequences, such as the recovery of lost or damaged data or
programs, arising from a culpable breach of duty by you.
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 25 / 25
CWP_BFV Dia 65 Double
Project: SA-13162-SF
Submitted by:
Date: 28/02/2024
Table of content
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 2 / 25
Version: 1.13.1
Support Details
Modular Support Spacing [mm] Undefined
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 3 / 25
Version: 1.13.1
Concrete
1.2 Nodes
X Y Z
No. No. Connector name Connector variant
[mm] [mm] [mm]
1 1 0.00 0.00 0.00 MT-B-O2 OC MT-B-O2 OC (C)
2 - 0.00 0.00 350.00 MT-C-LL1 OC MT-C-LL1 OC (C)
3 - 650.00 0.00 350.00 MT-C-LL1 OC MT-C-LL1 OC (C)
4 2 650.00 0.00 0.00 MT-B-O2 OC MT-B-O2 OC (C)
1.3 Members
Spring Constants
Releases
Member Translational Rotational
No. Cu,x Cu,y Cu,z Cφx Cφy Cφz
Ux Uy Uz φx φy φz
[kN/m] [kN/m] [kN/m] [kNm/Rad] [kNm/Rad] [kNm/Rad]
3 no no no no yes yes - - - - 0.001 0.001
1.6 Gliders
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 4 / 25
Version: 1.13.1
2 Part list
2.1 Members
Quantity Weight
Position Item Number Description
[-] [kg]
3 2272096 2-hole Baseplate MT-B-O2 OC 2 2.05
Quantity Weight
Position Item Number Description
[-] [kg]
7 2272049 Angle connector MT-C-LL1 OC 2 0.67
2.4 Other
Quantity Weight
Position Item Number Description
[-] [kg]
4 2273256 Hexagon bolt MT-TLB OC 8 0.20
5 2272082 Twist-Lock MT-TL M10 OC 8 0.28
6 2105870 Stud anchor HST3-R M12x115 40/20 4 0.41
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 5 / 25
Version: 1.13.1
3 Load Types
3. Loads
Custom loads
Position Fx Fy Fz Mx My Mz
Load No. Load Type Members
[mm] [kN] [kN] [kN] [kNm] [kNm] [kNm]
1 Design 2 150.00 0.00 0.00 -0.84 0.00 0.00 0.00
2 Design 2 500.00 0.00 0.00 -0.84 0.00 0.00 0.00
5 Wind (+x) 2 500.00 0.85 0.00 0.00 0.00 0.00 0.00
6 Wind (-x) 2 500.00 -0.85 -0.00 -0.00 -0.00 -0.00 -0.00
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 6 / 25
Version: 1.13.1
Start End
Fx Fy Fz Mx My Mz
Load No. Load Type Members Position Position
[kN/m] [kN/m] [kN/m] [kNm/m] [kNm/m] [kNm/m]
[mm] [mm]
19 Self Weight Support 1 0.00 350.00 0.00 0.00 -0.02 0.00 0.00 0.00
20 Self Weight Support 2 0.00 650.00 0.00 0.00 -0.02 0.00 0.00 0.00
21 Self Weight Support 3 0.00 350.00 0.00 0.00 -0.02 0.00 0.00 0.00
7 Design Permanent ☑
8 Wind (+x) Variable ☐
9 Wind (-x) Variable ☐
1 Self Weight Support Permanent ☑
☑All loads in these load cases are converted to seismic in +/-X, +/-Y and +/-Z
☐Loads not considered for seismic load conversion
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 7 / 25
Version: 1.13.1
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 8 / 25
Version: 1.13.1
4 Load Combinations
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 10 / 25
Version: 1.13.1
5 Results
5.1.3 Members
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 11 / 25
Version: 1.13.1
5.2 Members
Iω M Wy Wz Wy
[mm⁶] [kg/m] [mm³] [mm³] [mm³]
38410000.00 4.08 -2652.65 -3099.95 -2652.65
5.2.2.1 Overview
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 12 / 25
Version: 1.13.1
*006b-ULS: SW_sup + Wind (+x). Respective Combination Equation: 1.35 * LC1 + 1.50 * LC8
*007b-ULS: SW_sup + Wind (-x). Respective Combination Equation: 1.35 * LC1 + 1.50 * LC9
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 13 / 25
Version: 1.13.1
Beam No. 1
Beam No. 2
Beam No. 3
*006b-ULS: SW_sup + Wind (+x). Respective Combination Equation: 1.35 * LC1 + 1.50 * LC8
*007b-ULS: SW_sup + Wind (-x). Respective Combination Equation: 1.35 * LC1 + 1.50 * LC9
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 14 / 25
Version: 1.13.1
Normal load
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 15 / 25
Version: 1.13.1
Torsion around X
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 16 / 25
Version: 1.13.1
Moment around Y
Moment around Z
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 17 / 25
Version: 1.13.1
Buckling ratio
Criteria
☑Maximum Allowable Deflection (Beam) L/200
☑Maximum Allowable Deflection (Cantilever)L/150
- Maximum Deflection (Absolute) -
☑No Deflection checks calculated for 1.50mm
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 18 / 25
Version: 1.13.1
Overview
Results
Reference
Member Max deflection Utilization
Load Combination number* Governing criteria Length Limit
No. [mm] [%]
[mm]
1 016-SLS Relative (Beam) 350.00 L/200 -0.03 0.00
2 016-SLS Relative (Beam) 650.00 L/200 0.00 0.00
3 016-SLS Relative (Beam) 350.00 L/200 -0.00 0.00
*016-SLS: SW + Live + Snow + Wind (-x). Respective Combination Equation: 1.00 * LC1 + 1.00 * 0.60 * LC9
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 19 / 25
Version: 1.13.1
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 20 / 25
Version: 1.13.1
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 21 / 25
Version: 1.13.1
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 22 / 25
Version: 1.13.1
5.3 Connectors
5.3.1 Overview
Connector: MT-C-LL1 OC
Fx Fy Fz Mx My Mz
Connector variant: MT-C-LL1 OC (C)
[kN] [kN] [kN] [kNm] [kNm] [kNm]
Node No. : 2
Local Forces: -1.00 0.00 -0.35 0.00 0.13 0.00
Resistance: 8.20 1.24 8.06 0.03 0.19 0.03
abs(Fx.ed/Fx.rd)+abs(Fy.ed/Fy.rd)+abs(Fz.ed/Fz.rd)+abs(Mx.ed/Mx.rd)+abs(
Equation:
My.ed/My.rd)+abs(Mz.ed/Mz.rd)
Utilization: 81.97 % OK
Governing Load
1.35 * LC1 + 1.50 * LC9
Combination
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 23 / 25
Version: 1.13.1
5.4 Bases
5.4.1 Overview
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 24 / 25
Version: 1.13.1
Any and all information and data contained in the Software concern solely the use of Hilti products and based on the principles, formulas and security
regulations in accordance with Hilti's technical directions and operating, mounting and assembly instructions, etc., that must be strictly complied with by
the user. All figures contained therein are average figures, and therefore use-specific tests are to be conducted prior to using the relevant Hilti product.
The results of the calculations carried out by means of the Software are based essentially on the data you put in. Therefore, you bear the sole
responsibility for the absence of errors, the completeness and the relevance of the data to be put in by you. Moreover, you bear sole responsibility for
having the results of the calculation checked and cleared by an expert, particularly with regard to compliance with applicable norms and permits, prior
to using them for your specific facility. The Software servers only as an aid to interpret norms and permits without any guarantee as to the absence of
errors, the correctness and relevance ot the results or suitability for a specific application.
You must take all necessary and reasonable steps to prevent or limit damage caused by the Software. In particular, you must arrange for the regular
backup of programs and, if applicable, carry out the updates of that you are using the current and thus up-to-date version of the Software in each case
by carrying out manual updates via the Hilti Website. Hilti will not be liable for consequences, such as the recovery of lost or damaged data or
programs, arising from a culpable breach of duty by you.
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 25 / 25
CWP_GV Dia 50 Double
Project: SA-13162-SF
Submitted by:
Date: 28/02/2024
Table of content
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 2 / 25
Version: 1.13.1
Support Details
Modular Support Spacing [mm] Undefined
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 3 / 25
Version: 1.13.1
Concrete
1.2 Nodes
X Y Z
No. No. Connector name Connector variant
[mm] [mm] [mm]
1 1 0.00 0.00 0.00 MT-B-O2 OC MT-B-O2 OC (C)
2 - 0.00 0.00 350.00 MT-C-LL1 OC MT-C-LL1 OC (C)
3 - 560.00 0.00 350.00 MT-C-LL1 OC MT-C-LL1 OC (C)
4 2 560.00 0.00 0.00 MT-B-O2 OC MT-B-O2 OC (C)
1.3 Members
Spring Constants
Releases
Member Translational Rotational
No. Cu,x Cu,y Cu,z Cφx Cφy Cφz
Ux Uy Uz φx φy φz
[kN/m] [kN/m] [kN/m] [kNm/Rad] [kNm/Rad] [kNm/Rad]
1.6 Gliders
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 4 / 25
Version: 1.13.1
2 Part list
2.1 Members
Quantity Weight
Position Item Number Description
[-] [kg]
3 2272096 2-hole Baseplate MT-B-O2 OC 2 2.05
Quantity Weight
Position Item Number Description
[-] [kg]
7 2272049 Angle connector MT-C-LL1 OC 2 0.67
2.4 Other
Quantity Weight
Position Item Number Description
[-] [kg]
4 2273256 Hexagon bolt MT-TLB OC 8 0.20
5 2272082 Twist-Lock MT-TL M10 OC 8 0.28
6 2105870 Stud anchor HST3-R M12x115 40/20 4 0.41
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 5 / 25
Version: 1.13.1
3 Load Types
3. Loads
Custom loads
Position Fx Fy Fz Mx My Mz
Load No. Load Type Members
[mm] [kN] [kN] [kN] [kNm] [kNm] [kNm]
1 Design 2 150.00 0.00 0.00 -0.61 0.00 0.00 0.00
2 Design 2 410.00 0.00 0.00 -0.61 0.00 0.00 0.00
3 Wind (+x) 2 410.00 0.76 -0.00 -0.00 -0.00 -0.00 -0.00
4 Wind (-x) 2 410.00 -0.76 -0.00 -0.00 -0.00 -0.00 -0.00
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 6 / 25
Version: 1.13.1
Start End
Fx Fy Fz Mx My Mz
Load No. Load Type Members Position Position
[kN/m] [kN/m] [kN/m] [kNm/m] [kNm/m] [kNm/m]
[mm] [mm]
17 Self Weight Support 1 0.00 350.00 0.00 0.00 -0.02 0.00 0.00 0.00
18 Self Weight Support 2 0.00 560.00 0.00 0.00 -0.02 0.00 0.00 0.00
19 Self Weight Support 3 0.00 350.00 0.00 0.00 -0.02 0.00 0.00 0.00
7 Design Permanent ☑
8 Wind (+x) Variable ☐
9 Wind (-x) Variable ☐
1 Self Weight Support Permanent ☑
☑All loads in these load cases are converted to seismic in +/-X, +/-Y and +/-Z
☐Loads not considered for seismic load conversion
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 7 / 25
Version: 1.13.1
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 8 / 25
Version: 1.13.1
4 Load Combinations
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 10 / 25
Version: 1.13.1
5 Results
5.1.3 Members
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 11 / 25
Version: 1.13.1
5.2 Members
Iω M Wy Wz Wy
[mm⁶] [kg/m] [mm³] [mm³] [mm³]
38410000.00 4.08 -2652.65 -3099.95 -2652.65
5.2.2.1 Overview
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 12 / 25
Version: 1.13.1
*007b-ULS: SW_sup + Wind (-x). Respective Combination Equation: 1.35 * LC1 + 1.50 * LC9
*006b-ULS: SW_sup + Wind (+x). Respective Combination Equation: 1.35 * LC1 + 1.50 * LC8
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 13 / 25
Version: 1.13.1
Beam No. 1
Beam No. 2
Beam No. 3
*007b-ULS: SW_sup + Wind (-x). Respective Combination Equation: 1.35 * LC1 + 1.50 * LC9
*006b-ULS: SW_sup + Wind (+x). Respective Combination Equation: 1.35 * LC1 + 1.50 * LC8
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 14 / 25
Version: 1.13.1
Normal load
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 15 / 25
Version: 1.13.1
Torsion around X
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 16 / 25
Version: 1.13.1
Moment around Y
Moment around Z
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 17 / 25
Version: 1.13.1
Buckling ratio
Criteria
☑Maximum Allowable Deflection (Beam) L/200
☑Maximum Allowable Deflection (Cantilever)L/150
- Maximum Deflection (Absolute) -
☑No Deflection checks calculated for 1.50mm
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 18 / 25
Version: 1.13.1
Overview
Results
Reference
Member Max deflection Utilization
Load Combination number* Governing criteria Length Limit
No. [mm] [%]
[mm]
1 016-SLS Relative (Beam) 350.00 L/200 -0.02 0.00
2 016-SLS Relative (Beam) 560.00 L/200 0.00 0.00
3 016-SLS Relative (Beam) 350.00 L/200 -0.00 0.00
*016-SLS: SW + Live + Snow + Wind (-x). Respective Combination Equation: 1.00 * LC1 + 1.00 * 0.60 * LC9
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 19 / 25
Version: 1.13.1
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 20 / 25
Version: 1.13.1
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 21 / 25
Version: 1.13.1
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 22 / 25
Version: 1.13.1
5.3 Connectors
5.3.1 Overview
Connector: MT-C-LL1 OC
Fx Fy Fz Mx My Mz
Connector variant: MT-C-LL1 OC (C)
[kN] [kN] [kN] [kNm] [kNm] [kNm]
Node No. : 3
Local Forces: -0.57 0.00 -0.29 0.00 0.08 0.00
Resistance: 8.20 1.24 8.06 0.03 0.19 0.03
abs(Fx.ed/Fx.rd)+abs(Fy.ed/Fy.rd)+abs(Fz.ed/Fz.rd)+abs(Mx.ed/Mx.rd)+abs(
Equation:
My.ed/My.rd)+abs(Mz.ed/Mz.rd)
Utilization: 51.06 % OK
Governing Load
1.35 * LC1 + 1.50 * LC8
Combination
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 23 / 25
Version: 1.13.1
5.4 Bases
5.4.1 Overview
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 24 / 25
Version: 1.13.1
Any and all information and data contained in the Software concern solely the use of Hilti products and based on the principles, formulas and security
regulations in accordance with Hilti's technical directions and operating, mounting and assembly instructions, etc., that must be strictly complied with by
the user. All figures contained therein are average figures, and therefore use-specific tests are to be conducted prior to using the relevant Hilti product.
The results of the calculations carried out by means of the Software are based essentially on the data you put in. Therefore, you bear the sole
responsibility for the absence of errors, the completeness and the relevance of the data to be put in by you. Moreover, you bear sole responsibility for
having the results of the calculation checked and cleared by an expert, particularly with regard to compliance with applicable norms and permits, prior
to using them for your specific facility. The Software servers only as an aid to interpret norms and permits without any guarantee as to the absence of
errors, the correctness and relevance ot the results or suitability for a specific application.
You must take all necessary and reasonable steps to prevent or limit damage caused by the Software. In particular, you must arrange for the regular
backup of programs and, if applicable, carry out the updates of that you are using the current and thus up-to-date version of the Software in each case
by carrying out manual updates via the Hilti Website. Hilti will not be liable for consequences, such as the recovery of lost or damaged data or
programs, arising from a culpable breach of duty by you.
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 25 / 25
DRAIN Dia 110
Project: SA-13162-SF
Submitted by:
Date: 28/02/2024
Table of content
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 2 / 25
Version: 1.13.1
Support Details
Modular Support Spacing [mm] Undefined
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 3 / 25
Version: 1.13.1
1.1 Supports
Steel
Rotation
Node No. No. Orientation Steel grade Profile
[°]
1 1 Vertical ASTM A36/A36M W 12x136 0.00
1.2 Nodes
X Y Z
No. No. Connector name Connector variant
[mm] [mm] [mm]
1 1 0.00 0.00 0.00 MT-B-O2 OC MT-B-O2 OC (C_DF)
1.3 Members
Spring Constants
Releases
Member Translational Rotational
No. Cu,x Cu,y Cu,z Cφx Cφy Cφz
Ux Uy Uz φx φy φz
[kN/m] [kN/m] [kN/m] [kNm/Rad] [kNm/Rad] [kNm/Rad]
1.6 Gliders
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 4 / 25
Version: 1.13.1
2 Part list
2.1 Members
Quantity Weight
Position Item Number Description
[-] [kg]
2 2272096 2-hole Baseplate MT-B-O2 OC 1 1.03
Quantity Weight
Position Item Number Description
[-] [kg]
2.4 Other
Quantity Weight
Position Item Number Description
[-] [kg]
3 2273256 Hexagon bolt MT-TLB OC 2 0.05
4 2272082 Twist-Lock MT-TL M10 OC 2 0.07
5 2360102 Support plate FX 3-SP S 2 0.00
6 2184477 Flat washer 10 10,5x20x2 ISO 7089 A4 200 4 0.01
7 2194340 Threaded stud X-BT-MR M10/15 SN 8 2 0.02
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 5 / 25
Version: 1.13.1
3 Load Types
3. Loads
Custom loads
Position Fx Fy Fz Mx My Mz
Load No. Load Type Members
[mm] [kN] [kN] [kN] [kNm] [kNm] [kNm]
1 Design 1 210.00 0.00 0.00 -0.29 0.00 0.00 0.00
2 Wind (+y) 1 210.00 0.00 0.79 0.00 0.00 0.00 0.00
3 Wind (-y) 1 210.00 -0.00 -0.79 -0.00 -0.00 -0.00 -0.00
4 Seismic (+x) 1 210.00 0.01 -0.00 -0.00 -0.00 -0.00 -0.00
5 Seismic (-x) 1 210.00 -0.01 -0.00 -0.00 -0.00 -0.00 -0.00
6 Seismic (+y) 1 210.00 0.00 0.01 0.00 0.00 0.00 0.00
7 Seismic (-y) 1 210.00 -0.00 -0.01 -0.00 -0.00 -0.00 -0.00
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 6 / 25
Version: 1.13.1
Start End
Fx Fy Fz Mx My Mz
Load No. Load Type Members Position Position
[kN/m] [kN/m] [kN/m] [kNm/m] [kNm/m] [kNm/m]
[mm] [mm]
11 Self Weight Support 1 0.00 390.00 0.00 0.00 -0.02 0.00 0.00 0.00
7 Design Permanent ☑
8 Wind (+x) Variable ☐
9 Wind (-x) Variable ☐
10 Wind (+y) Variable ☐
11 Wind (-y) Variable ☐
1 Self Weight Support Permanent ☑
☑All loads in these load cases are converted to seismic in +/-X, +/-Y and +/-Z
☐Loads not considered for seismic load conversion
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 7 / 25
Version: 1.13.1
4 Load Combinations
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 8 / 25
Version: 1.13.1
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 9 / 25
Version: 1.13.1
5 Results
5.1.3 Members
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 10 / 25
Version: 1.13.1
5.2 Members
Iω M Wy Wz Wy
[mm⁶] [kg/m] [mm³] [mm³] [mm³]
38410000.00 2.04 -2652.65 -3099.95 -2652.65
5.2.2.1 Overview
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 11 / 25
Version: 1.13.1
*009b-ULS: SW_sup + Wind (-y). Respective Combination Equation: 1.35 * LC1 + 1.50 * LC11
Beam No. 1
*009b-ULS: SW_sup + Wind (-y). Respective Combination Equation: 1.35 * LC1 + 1.50 * LC11
Normal load
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 12 / 25
Version: 1.13.1
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 13 / 25
Version: 1.13.1
Torsion around X
Moment around Y
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 14 / 25
Version: 1.13.1
Moment around Z
Buckling ratio
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 15 / 25
Version: 1.13.1
Criteria
☑Maximum Allowable Deflection (Beam) L/200
☑Maximum Allowable Deflection (Cantilever)L/150
- Maximum Deflection (Absolute) -
☑No Deflection checks calculated for 1.50mm
Overview
Results
Reference
Member Max deflection Utilization
Load Combination number* Governing criteria Length Limit
No. [mm] [%]
[mm]
1 018-SLS Relative (Beam) 390.00 L/200 0.08 0.00
*018-SLS: SW + Live + Snow + Wind (-y). Respective Combination Equation: 1.00 * LC1 + 1.00 * 0.60 * LC11
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 16 / 25
Version: 1.13.1
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 17 / 25
Version: 1.13.1
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 18 / 25
Version: 1.13.1
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 19 / 25
Version: 1.13.1
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 20 / 25
Version: 1.13.1
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 21 / 25
Version: 1.13.1
5.3 Connectors
5.3.1 Overview
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 22 / 25
Version: 1.13.1
5.4 Bases
5.4.1 Overview
Fx Fy Fz Mx My Mz
Node No. 1.
[kN] [kN] [kN] [kNm] [kNm] [kNm]
Local Forces: 0.00 -0.02 1.18 0.00 -0.25 -0.00
Anchors X-BT-MR M10/15 SN 8
Base material
Thickness 6.00 [mm]
Governing Load
1.35 * LC1 + 1.50 * LC11
Combination
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 23 / 25
Version: 1.13.1
Calculation method
Standard
Anchor Design Checks
abs(Fx.ed/Fx.rd) ⋜ 1;abs(Fy.ed/Fy.rd) ⋜ 1;abs(Fz.ed/Fz.rd) ⋜ 1;abs(Mx.ed/Mx.rd) ⋜ 1;abs(My.ed/My.rd) ⋜ 1;abs(Mz.ed/Mz.rd) ⋜
1;
abs(Fx.ed/Fx.rd)+abs(Fy.ed/Fy.rd)+abs(Fz.ed/Fz.rd)+abs(Mx.ed/Mx.rd)+abs(My.ed/My.rd)+abs(Mz.ed/Mz.rd) ⋜ 1.2;
Resistance:
Anchor no. Vy Vz
1 - ✔
2 ✔ Friction Lock
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 24 / 25
Version: 1.13.1
Any and all information and data contained in the Software concern solely the use of Hilti products and based on the principles, formulas and security
regulations in accordance with Hilti's technical directions and operating, mounting and assembly instructions, etc., that must be strictly complied with by
the user. All figures contained therein are average figures, and therefore use-specific tests are to be conducted prior to using the relevant Hilti product.
The results of the calculations carried out by means of the Software are based essentially on the data you put in. Therefore, you bear the sole
responsibility for the absence of errors, the completeness and the relevance of the data to be put in by you. Moreover, you bear sole responsibility for
having the results of the calculation checked and cleared by an expert, particularly with regard to compliance with applicable norms and permits, prior
to using them for your specific facility. The Software servers only as an aid to interpret norms and permits without any guarantee as to the absence of
errors, the correctness and relevance ot the results or suitability for a specific application.
You must take all necessary and reasonable steps to prevent or limit damage caused by the Software. In particular, you must arrange for the regular
backup of programs and, if applicable, carry out the updates of that you are using the current and thus up-to-date version of the Software in each case
by carrying out manual updates via the Hilti Website. Hilti will not be liable for consequences, such as the recovery of lost or damaged data or
programs, arising from a culpable breach of duty by you.
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 25 / 25
DUCT 300x200 H 300
Project: SA-13162-SF
Submitted by:
Date: 04/03/2024
Table of content
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 2 / 25
Version: 1.13.1
Support Details
Modular Support Spacing [mm] Undefined
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 3 / 25
Version: 1.13.1
Concrete
1.2 Nodes
X Y Z
No. No. Connector name Connector variant
[mm] [mm] [mm]
1 1 0.00 0.00 0.00 MT-B-O2 OC MT-B-O2 OC (C)
2 - 0.00 0.00 300.00 MT-C-LL1 OC MT-C-LL1 OC (C)
3 - 650.00 0.00 300.00 MT-C-LL1 OC MT-C-LL1 OC (C)
4 2 650.00 0.00 0.00 MT-B-O2 OC MT-B-O2 OC (C)
1.3 Members
Spring Constants
Releases
Member Translational Rotational
No. Cu,x Cu,y Cu,z Cφx Cφy Cφz
Ux Uy Uz φx φy φz
[kN/m] [kN/m] [kN/m] [kNm/Rad] [kNm/Rad] [kNm/Rad]
2 no no no no yes yes - - - - 0.001 0.001
2 no no no no yes yes - - - - 0.001 0.001
1.6 Gliders
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 4 / 25
Version: 1.13.1
2 Part list
2.1 Members
Quantity Weight
Position Item Number Description
[-] [kg]
3 2272096 2-hole Baseplate MT-B-O2 OC 2 2.05
Quantity Weight
Position Item Number Description
[-] [kg]
7 2272049 Angle connector MT-C-LL1 OC 2 0.67
2.4 Other
Quantity Weight
Position Item Number Description
[-] [kg]
4 2273256 Hexagon bolt MT-TLB OC 8 0.20
5 2272082 Twist-Lock MT-TL M10 OC 8 0.28
6 2105870 Stud anchor HST3-R M12x115 40/20 4 0.41
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 5 / 25
Version: 1.13.1
3 Load Types
3. Loads
Custom loads
Position Fx Fy Fz Mx My Mz
Load No. Load Type Members
[mm] [kN] [kN] [kN] [kNm] [kNm] [kNm]
1 Design 2 175.00 0.00 0.00 -0.20 0.00 0.00 0.00
2 Design 2 475.00 0.00 0.00 -0.20 0.00 0.00 0.00
3 Design 2 325.00 0.00 0.00 -0.10 0.00 0.00 0.00
4 Wind (+x) 2 325.00 1.11 0.00 0.00 0.00 0.00 0.00
5 Wind (-x) 2 325.00 -1.11 -0.00 -0.00 -0.00 -0.00 -0.00
6 Seismic (+x) 2 325.00 0.01 0.00 0.00 0.00 0.00 0.00
7 Seismic (-x) 2 325.00 -0.01 -0.00 -0.00 -0.00 -0.00 -0.00
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 6 / 25
Version: 1.13.1
Start End
Fx Fy Fz Mx My Mz
Load No. Load Type Members Position Position
[kN/m] [kN/m] [kN/m] [kNm/m] [kNm/m] [kNm/m]
[mm] [mm]
14 Self Weight Support 1 0.00 300.00 0.00 0.00 -0.02 0.00 0.00 0.00
15 Self Weight Support 2 0.00 650.00 0.00 0.00 -0.02 0.00 0.00 0.00
16 Self Weight Support 3 0.00 300.00 0.00 0.00 -0.02 0.00 0.00 0.00
7 Design Permanent ☑
8 Wind (+x) Variable ☐
9 Wind (-x) Variable ☐
1 Self Weight Support Permanent ☑
☑All loads in these load cases are converted to seismic in +/-X, +/-Y and +/-Z
☐Loads not considered for seismic load conversion
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 7 / 25
Version: 1.13.1
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 8 / 25
Version: 1.13.1
4 Load Combinations
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 10 / 25
Version: 1.13.1
5 Results
5.1.3 Members
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 11 / 25
Version: 1.13.1
5.2 Members
Iω M Wy Wz Wy
[mm⁶] [kg/m] [mm³] [mm³] [mm³]
38410000.00 4.08 -2652.65 -3099.95 -2652.65
5.2.2.1 Overview
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 12 / 25
Version: 1.13.1
*006b-ULS: SW_sup + Wind (+x). Respective Combination Equation: 1.35 * LC1 + 1.50 * LC8
*004b-ULS: SW_sup + Design Loads. Respective Combination Equation: 1.35 * LC1 + 1.00 * LC7
*007b-ULS: SW_sup + Wind (-x). Respective Combination Equation: 1.35 * LC1 + 1.50 * LC9
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 13 / 25
Version: 1.13.1
Beam No. 1
Beam No. 2
Beam No. 3
*006b-ULS: SW_sup + Wind (+x). Respective Combination Equation: 1.35 * LC1 + 1.50 * LC8
*004b-ULS: SW_sup + Design Loads. Respective Combination Equation: 1.35 * LC1 + 1.00 * LC7
*007b-ULS: SW_sup + Wind (-x). Respective Combination Equation: 1.35 * LC1 + 1.50 * LC9
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 14 / 25
Version: 1.13.1
Normal load
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 15 / 25
Version: 1.13.1
Torsion around X
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 16 / 25
Version: 1.13.1
Moment around Y
Moment around Z
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 17 / 25
Version: 1.13.1
Buckling ratio
Criteria
☑Maximum Allowable Deflection (Beam) L/200
☑Maximum Allowable Deflection (Cantilever)L/150
- Maximum Deflection (Absolute) -
☑No Deflection checks calculated for 1.50mm
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 18 / 25
Version: 1.13.1
Overview
Results
Reference
Member Max deflection Utilization
Load Combination number* Governing criteria Length Limit
No. [mm] [%]
[mm]
1 016-SLS Relative (Beam) 300.00 L/200 -0.06 0.00
2 016-SLS Relative (Beam) 650.00 L/200 -0.00 0.00
3 016-SLS Relative (Beam) 300.00 L/200 -0.00 0.00
*016-SLS: SW + Live + Snow + Wind (-x). Respective Combination Equation: 1.00 * LC1 + 1.00 * 0.60 * LC9
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 19 / 25
Version: 1.13.1
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 20 / 25
Version: 1.13.1
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 21 / 25
Version: 1.13.1
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 22 / 25
Version: 1.13.1
5.3 Connectors
5.3.1 Overview
Connector: MT-C-LL1 OC
Fx Fy Fz Mx My Mz
Connector variant: MT-C-LL1 OC (C)
[kN] [kN] [kN] [kNm] [kNm] [kNm]
Node No. : 2
Local Forces: 0.83 0.00 -0.01 0.00 -0.00 -0.00
Resistance: 8.06 1.24 8.06 0.03 0.19 0.03
abs(Fx.ed/Fx.rd)+abs(Fy.ed/Fy.rd)+abs(Fz.ed/Fz.rd)+abs(Mx.ed/Mx.rd)+abs(
Equation:
My.ed/My.rd)+abs(Mz.ed/Mz.rd)
Utilization: 10.42 % OK
Governing Load
1.35 * LC1 + 1.50 * LC8
Combination
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 23 / 25
Version: 1.13.1
5.4 Bases
5.4.1 Overview
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 24 / 25
Version: 1.13.1
Any and all information and data contained in the Software concern solely the use of Hilti products and based on the principles, formulas and security
regulations in accordance with Hilti's technical directions and operating, mounting and assembly instructions, etc., that must be strictly complied with by
the user. All figures contained therein are average figures, and therefore use-specific tests are to be conducted prior to using the relevant Hilti product.
The results of the calculations carried out by means of the Software are based essentially on the data you put in. Therefore, you bear the sole
responsibility for the absence of errors, the completeness and the relevance of the data to be put in by you. Moreover, you bear sole responsibility for
having the results of the calculation checked and cleared by an expert, particularly with regard to compliance with applicable norms and permits, prior
to using them for your specific facility. The Software servers only as an aid to interpret norms and permits without any guarantee as to the absence of
errors, the correctness and relevance ot the results or suitability for a specific application.
You must take all necessary and reasonable steps to prevent or limit damage caused by the Software. In particular, you must arrange for the regular
backup of programs and, if applicable, carry out the updates of that you are using the current and thus up-to-date version of the Software in each case
by carrying out manual updates via the Hilti Website. Hilti will not be liable for consequences, such as the recovery of lost or damaged data or
programs, arising from a culpable breach of duty by you.
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 25 / 25
DUCT 400x350 H 300
Project: SA-13162-SF
Submitted by:
Date: 04/03/2024
Table of content
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 2 / 23
Version: 1.13.1
Support Details
Modular Support Spacing [mm] Undefined
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 3 / 23
Version: 1.13.1
Concrete
1.2 Nodes
X Y Z
No. No. Connector name Connector variant
[mm] [mm] [mm]
1 1 0.00 0.00 0.00 MT-B-O2 OC MT-B-O2 OC (C)
2 - 0.00 0.00 300.00 MT-C-LL1 OC MT-C-LL1 OC (C)
3 - 750.00 0.00 300.00 MT-C-LL1 OC MT-C-LL1 OC (C)
4 2 750.00 0.00 0.00 MT-B-O2 OC MT-B-O2 OC (C)
1.3 Members
Spring Constants
Releases
Member Translational Rotational
No. Cu,x Cu,y Cu,z Cφx Cφy Cφz
Ux Uy Uz φx φy φz
[kN/m] [kN/m] [kN/m] [kNm/Rad] [kNm/Rad] [kNm/Rad]
2 no no no no yes yes - - - - 0.001 0.001
2 no no no no yes yes - - - - 0.001 0.001
1.6 Gliders
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 4 / 23
Version: 1.13.1
2 Part list
2.1 Members
Quantity Weight
Position Item Number Description
[-] [kg]
3 2272096 2-hole Baseplate MT-B-O2 OC 2 2.05
Quantity Weight
Position Item Number Description
[-] [kg]
7 2272049 Angle connector MT-C-LL1 OC 2 0.67
2.4 Other
Quantity Weight
Position Item Number Description
[-] [kg]
4 2273256 Hexagon bolt MT-TLB OC 8 0.20
5 2272082 Twist-Lock MT-TL M10 OC 8 0.28
6 2105870 Stud anchor HST3-R M12x115 40/20 4 0.41
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 5 / 23
Version: 1.13.1
3 Load Types
3. Loads
Custom loads
Position Fx Fy Fz Mx My Mz
Load No. Load Type Members
[mm] [kN] [kN] [kN] [kNm] [kNm] [kNm]
1 Design 2 175.00 0.00 0.00 -0.32 0.00 0.00 0.00
2 Design 2 575.00 0.00 0.00 -0.32 0.00 0.00 0.00
3 Design 2 375.00 0.00 0.00 -0.16 0.00 0.00 0.00
4 Wind (+x) 2 375.00 1.94 0.00 0.00 0.00 0.00 0.00
5 Wind (-x) 2 375.00 -1.94 -0.00 -0.00 -0.00 -0.00 -0.00
6 Self Weight Support 1 0.00 0.00 0.00 -0.01 0.00 0.00 0.00
7 Self Weight Support 1 300.00 0.00 0.00 -0.00 0.00 0.00 0.00
8 Self Weight Support 2 750.00 0.00 0.00 -0.00 0.00 0.00 0.00
9 Self Weight Support 3 300.00 0.00 0.00 -0.01 0.00 0.00 0.00
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 6 / 23
Version: 1.13.1
Start End
Fx Fy Fz Mx My Mz
Load No. Load Type Members Position Position
[kN/m] [kN/m] [kN/m] [kNm/m] [kNm/m] [kNm/m]
[mm] [mm]
10 Self Weight Support 1 0.00 300.00 0.00 0.00 -0.02 0.00 0.00 0.00
11 Self Weight Support 2 0.00 750.00 0.00 0.00 -0.02 0.00 0.00 0.00
12 Self Weight Support 3 0.00 300.00 0.00 0.00 -0.02 0.00 0.00 0.00
7 Design Permanent ☑
8 Wind (+x) Variable ☐
9 Wind (-x) Variable ☐
1 Self Weight Support Permanent ☑
☑All loads in these load cases are converted to seismic in +/-X, +/-Y and +/-Z
☐Loads not considered for seismic load conversion
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 7 / 23
Version: 1.13.1
4 Load Combinations
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 8 / 23
Version: 1.13.1
5 Results
5.1.3 Members
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 9 / 23
Version: 1.13.1
5.2 Members
Iω M Wy Wz Wy
[mm⁶] [kg/m] [mm³] [mm³] [mm³]
38410000.00 4.08 -2652.65 -3099.95 -2652.65
5.2.2.1 Overview
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 10 / 23
Version: 1.13.1
*006b-ULS: SW_sup + Wind (+x). Respective Combination Equation: 1.35 * LC1 + 1.50 * LC8
*004b-ULS: SW_sup + Design Loads. Respective Combination Equation: 1.35 * LC1 + 1.00 * LC7
*007b-ULS: SW_sup + Wind (-x). Respective Combination Equation: 1.35 * LC1 + 1.50 * LC9
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 11 / 23
Version: 1.13.1
Beam No. 1
Beam No. 2
Beam No. 3
*006b-ULS: SW_sup + Wind (+x). Respective Combination Equation: 1.35 * LC1 + 1.50 * LC8
*004b-ULS: SW_sup + Design Loads. Respective Combination Equation: 1.35 * LC1 + 1.00 * LC7
*007b-ULS: SW_sup + Wind (-x). Respective Combination Equation: 1.35 * LC1 + 1.50 * LC9
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 12 / 23
Version: 1.13.1
Normal load
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 13 / 23
Version: 1.13.1
Torsion around X
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 14 / 23
Version: 1.13.1
Moment around Y
Moment around Z
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 15 / 23
Version: 1.13.1
Buckling ratio
Criteria
☑Maximum Allowable Deflection (Beam) L/200
☑Maximum Allowable Deflection (Cantilever)L/150
- Maximum Deflection (Absolute) -
☑No Deflection checks calculated for 1.50mm
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 16 / 23
Version: 1.13.1
Overview
Results
Reference
Member Max deflection Utilization
Load Combination number* Governing criteria Length Limit
No. [mm] [%]
[mm]
1 016-SLS Relative (Beam) 300.00 L/200 -0.05 0.00
2 016-SLS Relative (Beam) 750.00 L/200 -0.00 0.00
3 016-SLS Relative (Beam) 300.00 L/200 -0.00 0.00
*016-SLS: SW + Live + Snow + Wind (-x). Respective Combination Equation: 1.00 * LC1 + 1.00 * 0.60 * LC9
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 17 / 23
Version: 1.13.1
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 18 / 23
Version: 1.13.1
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 19 / 23
Version: 1.13.1
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 20 / 23
Version: 1.13.1
5.3 Connectors
5.3.1 Overview
Connector: MT-C-LL1 OC
Fx Fy Fz Mx My Mz
Connector variant: MT-C-LL1 OC (C)
[kN] [kN] [kN] [kNm] [kNm] [kNm]
Node No. : 2
Local Forces: 1.45 0.00 -0.01 0.00 -0.00 -0.00
Resistance: 8.06 1.24 8.06 0.03 0.19 0.03
abs(Fx.ed/Fx.rd)+abs(Fy.ed/Fy.rd)+abs(Fz.ed/Fz.rd)+abs(Mx.ed/Mx.rd)+abs(
Equation:
My.ed/My.rd)+abs(Mz.ed/Mz.rd)
Utilization: 18.16 % OK
Governing Load
1.35 * LC1 + 1.50 * LC8
Combination
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 21 / 23
Version: 1.13.1
5.4 Bases
5.4.1 Overview
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 22 / 23
Version: 1.13.1
Any and all information and data contained in the Software concern solely the use of Hilti products and based on the principles, formulas and security
regulations in accordance with Hilti's technical directions and operating, mounting and assembly instructions, etc., that must be strictly complied with by
the user. All figures contained therein are average figures, and therefore use-specific tests are to be conducted prior to using the relevant Hilti product.
The results of the calculations carried out by means of the Software are based essentially on the data you put in. Therefore, you bear the sole
responsibility for the absence of errors, the completeness and the relevance of the data to be put in by you. Moreover, you bear sole responsibility for
having the results of the calculation checked and cleared by an expert, particularly with regard to compliance with applicable norms and permits, prior
to using them for your specific facility. The Software servers only as an aid to interpret norms and permits without any guarantee as to the absence of
errors, the correctness and relevance ot the results or suitability for a specific application.
You must take all necessary and reasonable steps to prevent or limit damage caused by the Software. In particular, you must arrange for the regular
backup of programs and, if applicable, carry out the updates of that you are using the current and thus up-to-date version of the Software in each case
by carrying out manual updates via the Hilti Website. Hilti will not be liable for consequences, such as the recovery of lost or damaged data or
programs, arising from a culpable breach of duty by you.
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 23 / 23
DUCT 400x400 H 2000
Project: SA-13162-SF
Submitted by:
Date: 04/03/2024
Table of content
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 2 / 25
Version: 1.13.1
Support Details
Modular Support Spacing [mm] Undefined
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 3 / 25
Version: 1.13.1
Concrete
1.2 Nodes
X Y Z
No. No. Connector name Connector variant
[mm] [mm] [mm]
1 1 0.00 0.00 0.00 MT-B-GS T OC MT-B-GS T OC (C_MT-80)
2 - 0.00 0.00 2000.00 MT-C-GS A OC MT-C-GS A OC (C_D_CS)
3 - 750.00 0.00 2000.00 MT-C-GS A OC MT-C-GS A OC (C_D_CS)
4 2 750.00 0.00 0.00 MT-B-GS T OC MT-B-GS T OC (C_MT-80)
5 3 -350.00 0.00 0.00 MT-B-GS AB OC MT-B-GS AB OC (C)
6 - 0.00 0.00 350.00 MT-AB-G T OC MT-AB-G T OC (C_D)
7 4 1099.60 0.00 0.00 MT-B-GS AB OC MT-B-GS AB OC (C)
8 - 750.00 0.00 349.60 MT-AB-G T OC MT-AB-G T OC (C_D)
1.3 Members
Spring Constants
Releases
Member Translational Rotational
No. Cu,x Cu,y Cu,z Cφx Cφy Cφz
Ux Uy Uz φx φy φz
[kN/m] [kN/m] [kN/m] [kNm/Rad] [kNm/Rad] [kNm/Rad]
4 no no no no yes yes - - - - 0.000 0.000
4 no no no no yes yes - - - - 0.000 0.000
5 no no no no yes yes - - - - 0.000 0.000
5 no no no no yes yes - - - - 0.000 0.000
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 4 / 25
Version: 1.13.1
1.6 Gliders
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 5 / 25
Version: 1.13.1
2 Part list
2.1 Members
Quantity Weight
Position Item Number Description
[-] [kg]
5 2272100 Baseplate MT-B-GS T OC 2 4.33
9 2332787 Baseplate MT-B-GS AB OC 2 3.30
Quantity Weight
Position Item Number Description
[-] [kg]
8 2272068 Angle connector MT-C-GS A OC adjustable 4 1.56
11 2272116 Angle brace MT-AB-G T OC adjustable 4 1.39
2.4 Other
Quantity Weight
Position Item Number Description
[-] [kg]
6 2272084 Thread forming bolt MT-TFB OC 52 1.48
7 2105870 Stud anchor HST3-R M12x115 40/20 4 0.41
10 2018429 Anchor rod HIT-Z-R M12x105 4 0.41
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 6 / 25
Version: 1.13.1
3 Load Types
3. Loads
Custom loads
Position Fx Fy Fz Mx My Mz
Load No. Load Type Members
[mm] [kN] [kN] [kN] [kNm] [kNm] [kNm]
1 Design 2 175.00 0.00 0.00 -0.34 0.00 0.00 0.00
2 Design 2 575.00 0.00 0.00 -0.34 0.00 0.00 0.00
3 Design 2 375.00 0.00 0.00 -0.17 0.00 0.00 0.00
4 Wind (+x) 2 375.00 2.22 0.00 0.00 0.00 0.00 0.00
5 Wind (-x) 2 375.00 -2.22 -0.00 -0.00 -0.00 -0.00 -0.00
6 Self Weight Support 1 0.00 0.00 0.00 -0.02 0.00 0.00 0.00
7 Self Weight Support 1 2000.00 0.00 0.00 -0.01 0.00 0.00 0.00
8 Self Weight Support 2 750.00 0.00 0.00 -0.01 0.00 0.00 0.00
9 Self Weight Support 3 2000.00 0.00 0.00 -0.02 0.00 0.00 0.00
10 Self Weight Support 4 0.00 0.00 0.00 -0.02 0.00 0.00 0.00
11 Self Weight Support 1 350.00 0.00 0.00 -0.01 0.00 0.00 0.00
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 7 / 25
Version: 1.13.1
Start End
Fx Fy Fz Mx My Mz
Load No. Load Type Members Position Position
[kN/m] [kN/m] [kN/m] [kNm/m] [kNm/m] [kNm/m]
[mm] [mm]
14 Self Weight Support 1 0.00 2000.00 0.00 0.00 -0.06 0.00 0.00 0.00
15 Self Weight Support 2 0.00 750.00 0.00 0.00 -0.04 0.00 0.00 0.00
16 Self Weight Support 3 0.00 2000.00 0.00 0.00 -0.06 0.00 0.00 0.00
17 Self Weight Support 4 0.00 494.97 0.00 0.00 -0.04 0.00 0.00 0.00
18 Self Weight Support 5 0.00 494.41 0.00 0.00 -0.04 0.00 0.00 0.00
7 Design Permanent ☑
8 Wind (+x) Variable ☐
9 Wind (-x) Variable ☐
1 Self Weight Support Permanent ☑
☑All loads in these load cases are converted to seismic in +/-X, +/-Y and +/-Z
☐Loads not considered for seismic load conversion
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 8 / 25
Version: 1.13.1
4 Load Combinations
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 9 / 25
Version: 1.13.1
5 Results
5.1.3 Members
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 10 / 25
Version: 1.13.1
5.2 Members
Iω M Wy Wz Wy
[mm⁶] [kg/m] [mm³] [mm³] [mm³]
40950000.00 12.12 -17594.40 -9801.32 -17594.40
Iω M Wy Wz Wy
[mm⁶] [kg/m] [mm³] [mm³] [mm³]
2039000.00 3.91 -6349.48 -6349.48 -6349.48
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 11 / 25
Version: 1.13.1
5.2.2.1 Overview
*006b-ULS: SW_sup + Wind (+x). Respective Combination Equation: 1.35 * LC1 + 1.50 * LC8
*007b-ULS: SW_sup + Wind (-x). Respective Combination Equation: 1.35 * LC1 + 1.50 * LC9
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 12 / 25
Version: 1.13.1
Beam No. 1
Beam No. 2
Beam No. 3
Beam No. 4
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 13 / 25
Version: 1.13.1
Beam No. 5
*006b-ULS: SW_sup + Wind (+x). Respective Combination Equation: 1.35 * LC1 + 1.50 * LC8
*007b-ULS: SW_sup + Wind (-x). Respective Combination Equation: 1.35 * LC1 + 1.50 * LC9
Normal load
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 14 / 25
Version: 1.13.1
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 15 / 25
Version: 1.13.1
Torsion around X
Moment around Y
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 16 / 25
Version: 1.13.1
Moment around Z
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 17 / 25
Version: 1.13.1
Buckling ratio
Criteria
☑Maximum Allowable Deflection (Beam) L/200
☑Maximum Allowable Deflection (Cantilever)L/150
- Maximum Deflection (Absolute) -
☑No Deflection checks calculated for 1.50mm
Overview
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 18 / 25
Version: 1.13.1
Results
Reference
Member Max deflection Utilization
Load Combination number* Governing criteria Length Limit
No. [mm] [%]
[mm]
1 007-SLS Relative(Cantilever) 1650.00 L/150 5.40 49.07
2 016-SLS Relative (Beam) 750.00 L/200 0.01 0.00
3 006-SLS Relative(Cantilever) 1650.40 L/150 -5.40 49.06
4 016-SLS Relative (Beam) 494.97 L/200 0.03 0.00
5 016-SLS Relative (Beam) 494.41 L/200 -0.03 0.00
*007-SLS: SW + Wind (-x). Respective Combination Equation: 1.00 * LC1 + 1.00 * LC9
*016-SLS: SW + Live + Snow + Wind (-x). Respective Combination Equation: 1.00 * LC1 + 1.00 * 0.60 * LC9
*006-SLS: SW + Wind (+x). Respective Combination Equation: 1.00 * LC1 + 1.00 * LC8
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 19 / 25
Version: 1.13.1
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 20 / 25
Version: 1.13.1
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 21 / 25
Version: 1.13.1
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 22 / 25
Version: 1.13.1
5.3 Connectors
5.3.1 Overview
Connector: MT-C-GS A OC
Fx Fy Fz Mx My Mz
Connector variant: MT-C-GS A OC (C_D_CS)
[kN] [kN] [kN] [kNm] [kNm] [kNm]
Node No. : 2
Local Forces: 1.66 0.00 -2.80 0.00 1.06 0.00
Resistance: 25.24 10.59 41.34 1.06 2.21 0.40
abs(Fx.ed/Fx.rd)+abs(Fy.ed/Fy.rd)+abs(Fz.ed/Fz.rd)+abs(Mx.ed/Mx.rd)+abs(
Equation:
My.ed/My.rd)+abs(Mz.ed/Mz.rd)
Utilization: 61.11 % OK
Governing Load
1.00 * LC1 + 1.50 * LC8
Combination
Connector: MT-AB-G T OC
Fx Fy Fz Mx My Mz
Connector variant: MT-AB-G T OC (C_D)
[kN] [kN] [kN] [kNm] [kNm] [kNm]
Node No. : 8
Local Forces: 10.02 -0.01 -0.00 -0.00 0.00 -0.00
Resistance: 32.03 6.44 1.83
Equation: (( Fx.ed^2 + Fy.ed^2 )^0.5)/Fx.rd + Fz.ed / Fz.rd+Mx.ed/Mx.rd
Utilization: 31.29 % OK
Governing Load
1.00 * LC1 + 1.50 * LC9
Combination
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 23 / 25
Version: 1.13.1
5.4 Bases
5.4.1 Overview
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 24 / 25
Version: 1.13.1
Any and all information and data contained in the Software concern solely the use of Hilti products and based on the principles, formulas and security
regulations in accordance with Hilti's technical directions and operating, mounting and assembly instructions, etc., that must be strictly complied with by
the user. All figures contained therein are average figures, and therefore use-specific tests are to be conducted prior to using the relevant Hilti product.
The results of the calculations carried out by means of the Software are based essentially on the data you put in. Therefore, you bear the sole
responsibility for the absence of errors, the completeness and the relevance of the data to be put in by you. Moreover, you bear sole responsibility for
having the results of the calculation checked and cleared by an expert, particularly with regard to compliance with applicable norms and permits, prior
to using them for your specific facility. The Software servers only as an aid to interpret norms and permits without any guarantee as to the absence of
errors, the correctness and relevance ot the results or suitability for a specific application.
You must take all necessary and reasonable steps to prevent or limit damage caused by the Software. In particular, you must arrange for the regular
backup of programs and, if applicable, carry out the updates of that you are using the current and thus up-to-date version of the Software in each case
by carrying out manual updates via the Hilti Website. Hilti will not be liable for consequences, such as the recovery of lost or damaged data or
programs, arising from a culpable breach of duty by you.
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 25 / 25
DUCT 500x250 H 300
Project: SA-13162-SF
Submitted by:
Date: 04/03/2024
Table of content
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 2 / 23
Version: 1.13.1
Support Details
Modular Support Spacing [mm] Undefined
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 3 / 23
Version: 1.13.1
Concrete
1.2 Nodes
X Y Z
No. No. Connector name Connector variant
[mm] [mm] [mm]
1 1 0.00 0.00 0.00 MT-B-O2 OC MT-B-O2 OC (C)
2 - 0.00 0.00 300.00 MT-C-LL1 OC MT-C-LL1 OC (C)
3 - 850.00 0.00 300.00 MT-C-LL1 OC MT-C-LL1 OC (C)
4 2 850.00 0.00 0.00 MT-B-O2 OC MT-B-O2 OC (C)
1.3 Members
Spring Constants
Releases
Member Translational Rotational
No. Cu,x Cu,y Cu,z Cφx Cφy Cφz
Ux Uy Uz φx φy φz
[kN/m] [kN/m] [kN/m] [kNm/Rad] [kNm/Rad] [kNm/Rad]
2 no no no no yes yes - - - - 0.001 0.001
2 no no no no yes yes - - - - 0.001 0.001
1.6 Gliders
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 4 / 23
Version: 1.13.1
2 Part list
2.1 Members
Quantity Weight
Position Item Number Description
[-] [kg]
3 2272096 2-hole Baseplate MT-B-O2 OC 2 2.05
Quantity Weight
Position Item Number Description
[-] [kg]
7 2272049 Angle connector MT-C-LL1 OC 2 0.67
2.4 Other
Quantity Weight
Position Item Number Description
[-] [kg]
4 2273256 Hexagon bolt MT-TLB OC 8 0.20
5 2272082 Twist-Lock MT-TL M10 OC 8 0.28
6 2105870 Stud anchor HST3-R M12x115 40/20 4 0.41
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 5 / 23
Version: 1.13.1
3 Load Types
3. Loads
Custom loads
Position Fx Fy Fz Mx My Mz
Load No. Load Type Members
[mm] [kN] [kN] [kN] [kNm] [kNm] [kNm]
1 Design 2 175.00 0.00 0.00 -0.36 0.00 0.00 0.00
2 Design 2 675.00 0.00 0.00 -0.36 0.00 0.00 0.00
3 Design 2 424.00 0.00 0.00 -0.18 0.00 0.00 0.00
4 Wind (+x) 2 425.00 1.39 -0.00 -0.00 -0.00 -0.00 -0.00
5 Wind (-x) 2 425.00 -1.39 -0.00 -0.00 -0.00 -0.00 -0.00
6 Self Weight Support 1 0.00 0.00 0.00 -0.01 0.00 0.00 0.00
7 Self Weight Support 1 300.00 0.00 0.00 -0.00 0.00 0.00 0.00
8 Self Weight Support 2 850.00 0.00 0.00 -0.00 0.00 0.00 0.00
9 Self Weight Support 3 300.00 0.00 0.00 -0.01 0.00 0.00 0.00
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 6 / 23
Version: 1.13.1
Start End
Fx Fy Fz Mx My Mz
Load No. Load Type Members Position Position
[kN/m] [kN/m] [kN/m] [kNm/m] [kNm/m] [kNm/m]
[mm] [mm]
10 Self Weight Support 1 0.00 300.00 0.00 0.00 -0.02 0.00 0.00 0.00
11 Self Weight Support 2 0.00 850.00 0.00 0.00 -0.02 0.00 0.00 0.00
12 Self Weight Support 3 0.00 300.00 0.00 0.00 -0.02 0.00 0.00 0.00
7 Design Permanent ☑
8 Wind (+x) Variable ☐
9 Wind (-x) Variable ☐
1 Self Weight Support Permanent ☑
☑All loads in these load cases are converted to seismic in +/-X, +/-Y and +/-Z
☐Loads not considered for seismic load conversion
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 7 / 23
Version: 1.13.1
4 Load Combinations
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 8 / 23
Version: 1.13.1
5 Results
5.1.3 Members
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 9 / 23
Version: 1.13.1
5.2 Members
Iω M Wy Wz Wy
[mm⁶] [kg/m] [mm³] [mm³] [mm³]
38410000.00 4.08 -2652.65 -3099.95 -2652.65
5.2.2.1 Overview
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 10 / 23
Version: 1.13.1
*006b-ULS: SW_sup + Wind (+x). Respective Combination Equation: 1.35 * LC1 + 1.50 * LC8
*004b-ULS: SW_sup + Design Loads. Respective Combination Equation: 1.35 * LC1 + 1.00 * LC7
*007b-ULS: SW_sup + Wind (-x). Respective Combination Equation: 1.35 * LC1 + 1.50 * LC9
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 11 / 23
Version: 1.13.1
Beam No. 1
Beam No. 2
Beam No. 3
*006b-ULS: SW_sup + Wind (+x). Respective Combination Equation: 1.35 * LC1 + 1.50 * LC8
*004b-ULS: SW_sup + Design Loads. Respective Combination Equation: 1.35 * LC1 + 1.00 * LC7
*007b-ULS: SW_sup + Wind (-x). Respective Combination Equation: 1.35 * LC1 + 1.50 * LC9
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 12 / 23
Version: 1.13.1
Normal load
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 13 / 23
Version: 1.13.1
Torsion around X
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 14 / 23
Version: 1.13.1
Moment around Y
Moment around Z
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 15 / 23
Version: 1.13.1
Buckling ratio
Criteria
☑Maximum Allowable Deflection (Beam) L/200
☑Maximum Allowable Deflection (Cantilever)L/150
- Maximum Deflection (Absolute) -
☑No Deflection checks calculated for 1.50mm
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 16 / 23
Version: 1.13.1
Overview
Results
Reference
Member Max deflection Utilization
Load Combination number* Governing criteria Length Limit
No. [mm] [%]
[mm]
1 016-SLS Relative (Beam) 300.00 L/200 -0.02 0.00
2 016-SLS Relative (Beam) 850.00 L/200 -0.00 0.00
3 016-SLS Relative (Beam) 300.00 L/200 -0.00 0.00
*016-SLS: SW + Live + Snow + Wind (-x). Respective Combination Equation: 1.00 * LC1 + 1.00 * 0.60 * LC9
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 17 / 23
Version: 1.13.1
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 18 / 23
Version: 1.13.1
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 19 / 23
Version: 1.13.1
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 20 / 23
Version: 1.13.1
5.3 Connectors
5.3.1 Overview
Connector: MT-C-LL1 OC
Fx Fy Fz Mx My Mz
Connector variant: MT-C-LL1 OC (C)
[kN] [kN] [kN] [kNm] [kNm] [kNm]
Node No. : 2
Local Forces: 1.04 0.00 -0.01 0.00 -0.00 -0.00
Resistance: 8.06 1.24 8.06 0.03 0.19 0.03
abs(Fx.ed/Fx.rd)+abs(Fy.ed/Fy.rd)+abs(Fz.ed/Fz.rd)+abs(Mx.ed/Mx.rd)+abs(
Equation:
My.ed/My.rd)+abs(Mz.ed/Mz.rd)
Utilization: 13.06 % OK
Governing Load
1.35 * LC1 + 1.50 * LC8
Combination
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 21 / 23
Version: 1.13.1
5.4 Bases
5.4.1 Overview
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 22 / 23
Version: 1.13.1
Any and all information and data contained in the Software concern solely the use of Hilti products and based on the principles, formulas and security
regulations in accordance with Hilti's technical directions and operating, mounting and assembly instructions, etc., that must be strictly complied with by
the user. All figures contained therein are average figures, and therefore use-specific tests are to be conducted prior to using the relevant Hilti product.
The results of the calculations carried out by means of the Software are based essentially on the data you put in. Therefore, you bear the sole
responsibility for the absence of errors, the completeness and the relevance of the data to be put in by you. Moreover, you bear sole responsibility for
having the results of the calculation checked and cleared by an expert, particularly with regard to compliance with applicable norms and permits, prior
to using them for your specific facility. The Software servers only as an aid to interpret norms and permits without any guarantee as to the absence of
errors, the correctness and relevance ot the results or suitability for a specific application.
You must take all necessary and reasonable steps to prevent or limit damage caused by the Software. In particular, you must arrange for the regular
backup of programs and, if applicable, carry out the updates of that you are using the current and thus up-to-date version of the Software in each case
by carrying out manual updates via the Hilti Website. Hilti will not be liable for consequences, such as the recovery of lost or damaged data or
programs, arising from a culpable breach of duty by you.
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 23 / 23
DUCT 500x500 H 2200
Project: SA-13162-SF
Submitted by:
Date: 04/03/2024
Table of content
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 2 / 25
Version: 1.13.1
Support Details
Modular Support Spacing [mm] Undefined
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 3 / 25
Version: 1.13.1
Concrete
1.2 Nodes
X Y Z
No. No. Connector name Connector variant
[mm] [mm] [mm]
1 1 0.00 0.00 0.00 MT-B-GS T OC MT-B-GS T OC (C_MT-80)
2 - 0.00 0.00 2200.00 MT-C-GS A OC MT-C-GS A OC (C_D_CS)
3 - 850.00 0.00 2200.00 MT-C-GS A OC MT-C-GS A OC (C_D_CS)
4 2 850.00 0.00 0.00 MT-B-GS T OC MT-B-GS T OC (C_MT-80)
5 3 350.00 0.00 0.00 MT-B-GS AB OC MT-B-GS AB OC (C)
6 - -0.00 0.00 350.00 MT-AB-G T OC MT-AB-G T OC (C_D)
7 4 500.00 0.00 0.00 MT-B-GS AB OC MT-B-GS AB OC (C)
8 - 850.00 0.00 350.00 MT-AB-G T OC MT-AB-G T OC (C_D)
1.3 Members
Spring Constants
Releases
Member Translational Rotational
No. Cu,x Cu,y Cu,z Cφx Cφy Cφz
Ux Uy Uz φx φy φz
[kN/m] [kN/m] [kN/m] [kNm/Rad] [kNm/Rad] [kNm/Rad]
4 no no no no yes yes - - - - 0.000 0.000
4 no no no no yes yes - - - - 0.000 0.000
5 no no no no yes yes - - - - 0.000 0.000
5 no no no no yes yes - - - - 0.000 0.000
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 4 / 25
Version: 1.13.1
1.6 Gliders
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 5 / 25
Version: 1.13.1
2 Part list
2.1 Members
Quantity Weight
Position Item Number Description
[-] [kg]
4 2272100 Baseplate MT-B-GS T OC 2 4.33
8 2332787 Baseplate MT-B-GS AB OC 2 3.30
Quantity Weight
Position Item Number Description
[-] [kg]
7 2272068 Angle connector MT-C-GS A OC adjustable 4 1.56
10 2272116 Angle brace MT-AB-G T OC adjustable 4 1.39
2.4 Other
Quantity Weight
Position Item Number Description
[-] [kg]
5 2272084 Thread forming bolt MT-TFB OC 52 1.48
6 2105870 Stud anchor HST3-R M12x115 40/20 4 0.41
9 2018429 Anchor rod HIT-Z-R M12x105 4 0.41
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 6 / 25
Version: 1.13.1
3 Load Types
3. Loads
Custom loads
Position Fx Fy Fz Mx My Mz
Load No. Load Type Members
[mm] [kN] [kN] [kN] [kNm] [kNm] [kNm]
1 Design 2 175.00 0.00 0.00 -0.47 0.00 0.00 0.00
2 Design 2 675.00 0.00 0.00 -0.47 0.00 0.00 0.00
3 Design 2 425.00 0.00 0.00 -0.23 0.00 0.00 0.00
4 Wind (+x) 2 425.00 2.77 -0.00 -0.00 -0.00 -0.00 -0.00
5 Wind (-x) 2 425.00 -2.77 -0.00 -0.00 -0.00 -0.00 -0.00
6 Self Weight Support 1 0.00 0.00 0.00 -0.02 0.00 0.00 0.00
7 Self Weight Support 1 2200.00 0.00 0.00 -0.01 0.00 0.00 0.00
8 Self Weight Support 2 850.00 0.00 0.00 -0.01 0.00 0.00 0.00
9 Self Weight Support 3 2200.00 0.00 0.00 -0.02 0.00 0.00 0.00
10 Self Weight Support 4 0.00 0.00 0.00 -0.02 0.00 0.00 0.00
11 Self Weight Support 1 350.00 0.00 0.00 -0.01 0.00 0.00 0.00
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 7 / 25
Version: 1.13.1
Start End
Fx Fy Fz Mx My Mz
Load No. Load Type Members Position Position
[kN/m] [kN/m] [kN/m] [kNm/m] [kNm/m] [kNm/m]
[mm] [mm]
14 Self Weight Support 1 0.00 2200.00 0.00 0.00 -0.06 0.00 0.00 0.00
15 Self Weight Support 2 0.00 850.00 0.00 0.00 -0.04 0.00 0.00 0.00
16 Self Weight Support 3 0.00 2200.00 0.00 0.00 -0.06 0.00 0.00 0.00
17 Self Weight Support 4 0.00 494.97 0.00 0.00 -0.04 0.00 0.00 0.00
18 Self Weight Support 5 0.00 494.97 0.00 0.00 -0.04 0.00 0.00 0.00
7 Design Permanent ☑
8 Wind (+x) Variable ☐
9 Wind (-x) Variable ☐
1 Self Weight Support Permanent ☑
☑All loads in these load cases are converted to seismic in +/-X, +/-Y and +/-Z
☐Loads not considered for seismic load conversion
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 8 / 25
Version: 1.13.1
4 Load Combinations
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 9 / 25
Version: 1.13.1
5 Results
5.1.3 Members
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 10 / 25
Version: 1.13.1
5.2 Members
Iω M Wy Wz Wy
[mm⁶] [kg/m] [mm³] [mm³] [mm³]
40950000.00 12.12 -17594.40 -9801.32 -17594.40
Iω M Wy Wz Wy
[mm⁶] [kg/m] [mm³] [mm³] [mm³]
2039000.00 3.91 -6349.48 -6349.48 -6349.48
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 11 / 25
Version: 1.13.1
5.2.2.1 Overview
*007b-ULS: SW_sup + Wind (-x). Respective Combination Equation: 1.35 * LC1 + 1.50 * LC9
*006b-ULS: SW_sup + Wind (+x). Respective Combination Equation: 1.35 * LC1 + 1.50 * LC8
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 12 / 25
Version: 1.13.1
Beam No. 1
Beam No. 2
Beam No. 3
Beam No. 4
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 13 / 25
Version: 1.13.1
Beam No. 5
*007b-ULS: SW_sup + Wind (-x). Respective Combination Equation: 1.35 * LC1 + 1.50 * LC9
*006b-ULS: SW_sup + Wind (+x). Respective Combination Equation: 1.35 * LC1 + 1.50 * LC8
Normal load
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 14 / 25
Version: 1.13.1
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 15 / 25
Version: 1.13.1
Torsion around X
Moment around Y
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 16 / 25
Version: 1.13.1
Moment around Z
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 17 / 25
Version: 1.13.1
Buckling ratio
Criteria
☑Maximum Allowable Deflection (Beam) L/200
☑Maximum Allowable Deflection (Cantilever)L/150
- Maximum Deflection (Absolute) -
☑No Deflection checks calculated for 1.50mm
Overview
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 18 / 25
Version: 1.13.1
Results
Reference
Member Max deflection Utilization
Load Combination number* Governing criteria Length Limit
No. [mm] [%]
[mm]
1 006-SLS Relative(Cantilever) 1850.00 L/150 -9.38 76.07
2 016-SLS Relative (Beam) 850.00 L/200 0.03 0.00
3 007-SLS Relative(Cantilever) 1850.00 L/150 9.38 76.07
4 016-SLS Relative (Beam) 494.97 L/200 -0.05 0.00
5 016-SLS Relative (Beam) 494.97 L/200 0.05 0.00
*006-SLS: SW + Wind (+x). Respective Combination Equation: 1.00 * LC1 + 1.00 * LC8
*016-SLS: SW + Live + Snow + Wind (-x). Respective Combination Equation: 1.00 * LC1 + 1.00 * 0.60 * LC9
*007-SLS: SW + Wind (-x). Respective Combination Equation: 1.00 * LC1 + 1.00 * LC9
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 19 / 25
Version: 1.13.1
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 20 / 25
Version: 1.13.1
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 21 / 25
Version: 1.13.1
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 22 / 25
Version: 1.13.1
5.3 Connectors
5.3.1 Overview
Connector: MT-C-GS A OC
Fx Fy Fz Mx My Mz
Connector variant: MT-C-GS A OC (C_D_CS)
[kN] [kN] [kN] [kNm] [kNm] [kNm]
Node No. : 2
Local Forces: 2.08 0.00 -3.42 0.00 1.46 0.00
Resistance: 25.24 10.59 41.34 1.06 2.21 0.40
abs(Fx.ed/Fx.rd)+abs(Fy.ed/Fy.rd)+abs(Fz.ed/Fz.rd)+abs(Mx.ed/Mx.rd)+abs(
Equation:
My.ed/My.rd)+abs(Mz.ed/Mz.rd)
Utilization: 82.47 % OK
Governing Load
1.00 * LC1 + 1.50 * LC8
Combination
Connector: MT-AB-G T OC
Fx Fy Fz Mx My Mz
Connector variant: MT-AB-G T OC (C_D)
[kN] [kN] [kN] [kNm] [kNm] [kNm]
Node No. : 6
Local Forces: 13.52 -0.01 0.00 0.00 0.00 -0.00
Resistance: 32.03 6.44 1.83
Equation: (( Fx.ed^2 + Fy.ed^2 )^0.5)/Fx.rd + Fz.ed / Fz.rd+Mx.ed/Mx.rd
Utilization: 42.19 % OK
Governing Load
1.35 * LC1 + 1.50 * LC9
Combination
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 23 / 25
Version: 1.13.1
5.4 Bases
5.4.1 Overview
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 24 / 25
Version: 1.13.1
Any and all information and data contained in the Software concern solely the use of Hilti products and based on the principles, formulas and security
regulations in accordance with Hilti's technical directions and operating, mounting and assembly instructions, etc., that must be strictly complied with by
the user. All figures contained therein are average figures, and therefore use-specific tests are to be conducted prior to using the relevant Hilti product.
The results of the calculations carried out by means of the Software are based essentially on the data you put in. Therefore, you bear the sole
responsibility for the absence of errors, the completeness and the relevance of the data to be put in by you. Moreover, you bear sole responsibility for
having the results of the calculation checked and cleared by an expert, particularly with regard to compliance with applicable norms and permits, prior
to using them for your specific facility. The Software servers only as an aid to interpret norms and permits without any guarantee as to the absence of
errors, the correctness and relevance ot the results or suitability for a specific application.
You must take all necessary and reasonable steps to prevent or limit damage caused by the Software. In particular, you must arrange for the regular
backup of programs and, if applicable, carry out the updates of that you are using the current and thus up-to-date version of the Software in each case
by carrying out manual updates via the Hilti Website. Hilti will not be liable for consequences, such as the recovery of lost or damaged data or
programs, arising from a culpable breach of duty by you.
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 25 / 25
DUCT 550x500 H 650
Project: SA-13162-SF
Submitted by:
Date: 04/03/2024
Table of content
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 2 / 24
Version: 1.13.1
Support Details
Modular Support Spacing [mm] Undefined
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 3 / 24
Version: 1.13.1
Concrete
1.2 Nodes
X Y Z
No. No. Connector name Connector variant
[mm] [mm] [mm]
1 1 0.00 0.00 0.00 MT-B-O2 OC MT-B-O2 OC (C)
2 - 0.00 0.00 650.00 MT-C-LL1 OC MT-C-LL1 OC (C)
3 - 900.00 0.00 650.00 MT-C-LL1 OC MT-C-LL1 OC (C)
4 2 900.00 0.00 0.00 MT-B-O2 OC MT-B-O2 OC (C)
5 3 300.00 0.00 0.00 MT-AB A OC MT-AB A OC (C)
6 - 0.00 0.00 300.00 MT-AB A OC MT-AB A OC (C)
7 4 600.00 0.00 0.00 MT-AB A OC MT-AB A OC (C)
8 - 900.00 0.00 300.00 MT-AB A OC MT-AB A OC (C)
1.3 Members
Spring Constants
Releases
Member Translational Rotational
No. Cu,x Cu,y Cu,z Cφx Cφy Cφz
Ux Uy Uz φx φy φz
[kN/m] [kN/m] [kN/m] [kNm/Rad] [kNm/Rad] [kNm/Rad]
2 no no no no yes yes - - - - 0.001 0.001
2 no no no no yes yes - - - - 0.001 0.001
4 no no no no yes yes - - - - 0.000 0.000
4 no no no no yes yes - - - - 0.000 0.000
5 no no no no yes yes - - - - 0.000 0.000
5 no no no no yes yes - - - - 0.000 0.000
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 4 / 24
Version: 1.13.1
1.6 Gliders
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 5 / 24
Version: 1.13.1
2 Part list
2.1 Members
Quantity Weight
Position Item Number Description
[-] [kg]
4 2272096 2-hole Baseplate MT-B-O2 OC 2 2.05
9 2346396 Angle brace MT-AB A OC set adjustable 4 1.77
Quantity Weight
Position Item Number Description
[-] [kg]
8 2272049 Angle connector MT-C-LL1 OC 2 0.67
9 2346396 Angle brace MT-AB A OC set adjustable 4 1.77
2.4 Other
Quantity Weight
Position Item Number Description
[-] [kg]
5 2273256 Hexagon bolt MT-TLB OC 12 0.30
6 2272082 Twist-Lock MT-TL M10 OC 12 0.42
7 2105870 Stud anchor HST3-R M12x115 40/20 8 0.81
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 6 / 24
Version: 1.13.1
3 Load Types
3. Loads
Custom loads
Position Fx Fy Fz Mx My Mz
Load No. Load Type Members
[mm] [kN] [kN] [kN] [kNm] [kNm] [kNm]
1 Design 2 175.00 0.00 0.00 -0.49 0.00 0.00 0.00
2 Design 2 725.00 0.00 0.00 -0.49 0.00 0.00 0.00
3 Design 2 450.00 0.00 0.00 -0.25 0.00 0.00 0.00
4 Wind (+x) 2 450.00 2.77 -0.00 -0.00 -0.00 -0.00 -0.00
5 Wind (-x) 2 450.00 -2.77 -0.00 -0.00 -0.00 -0.00 -0.00
6 Self Weight Support 1 0.00 0.00 0.00 -0.01 0.00 0.00 0.00
7 Self Weight Support 1 650.00 0.00 0.00 -0.00 0.00 0.00 0.00
8 Self Weight Support 2 900.00 0.00 0.00 -0.00 0.00 0.00 0.00
9 Self Weight Support 3 650.00 0.00 0.00 -0.01 0.00 0.00 0.00
10 Self Weight Support 4 0.00 0.00 0.00 -0.00 0.00 0.00 0.00
11 Self Weight Support 1 300.00 0.00 0.00 -0.00 0.00 0.00 0.00
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 7 / 24
Version: 1.13.1
Start End
Fx Fy Fz Mx My Mz
Load No. Load Type Members Position Position
[kN/m] [kN/m] [kN/m] [kNm/m] [kNm/m] [kNm/m]
[mm] [mm]
14 Self Weight Support 1 0.00 650.00 0.00 0.00 -0.04 0.00 0.00 0.00
15 Self Weight Support 2 0.00 900.00 0.00 0.00 -0.02 0.00 0.00 0.00
16 Self Weight Support 3 0.00 650.00 0.00 0.00 -0.04 0.00 0.00 0.00
17 Self Weight Support 4 0.00 424.26 0.00 0.00 -0.02 0.00 0.00 0.00
18 Self Weight Support 5 0.00 424.26 0.00 0.00 -0.02 0.00 0.00 0.00
7 Design Permanent ☑
8 Wind (+x) Variable ☐
9 Wind (-x) Variable ☐
1 Self Weight Support Permanent ☑
☑All loads in these load cases are converted to seismic in +/-X, +/-Y and +/-Z
☐Loads not considered for seismic load conversion
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 8 / 24
Version: 1.13.1
4 Load Combinations
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 9 / 24
Version: 1.13.1
5 Results
5.1.3 Members
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 10 / 24
Version: 1.13.1
5.2 Members
Iω M Wy Wz Wy
[mm⁶] [kg/m] [mm³] [mm³] [mm³]
158106000.00 7.71 -7804.06 -8037.37 -7804.06
Iω M Wy Wz Wy
[mm⁶] [kg/m] [mm³] [mm³] [mm³]
38410000.00 2.04 -2652.65 -3099.95 -2652.65
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 11 / 24
Version: 1.13.1
5.2.2.1 Overview
*007b-ULS: SW_sup + Wind (-x). Respective Combination Equation: 1.35 * LC1 + 1.50 * LC9
*004b-ULS: SW_sup + Design Loads. Respective Combination Equation: 1.35 * LC1 + 1.00 * LC7
*006b-ULS: SW_sup + Wind (+x). Respective Combination Equation: 1.35 * LC1 + 1.50 * LC8
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 12 / 24
Version: 1.13.1
Beam No. 1
Beam No. 2
Beam No. 3
Beam No. 4
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 13 / 24
Version: 1.13.1
Beam No. 5
*007b-ULS: SW_sup + Wind (-x). Respective Combination Equation: 1.35 * LC1 + 1.50 * LC9
*004b-ULS: SW_sup + Design Loads. Respective Combination Equation: 1.35 * LC1 + 1.00 * LC7
*006b-ULS: SW_sup + Wind (+x). Respective Combination Equation: 1.35 * LC1 + 1.50 * LC8
Normal load
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 14 / 24
Version: 1.13.1
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 15 / 24
Version: 1.13.1
Torsion around X
Moment around Y
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 16 / 24
Version: 1.13.1
Moment around Z
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 17 / 24
Version: 1.13.1
Buckling ratio
Criteria
☑Maximum Allowable Deflection (Beam) L/200
☑Maximum Allowable Deflection (Cantilever)L/150
- Maximum Deflection (Absolute) -
☑No Deflection checks calculated for 1.50mm
Overview
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 18 / 24
Version: 1.13.1
Results
Reference
Member Max deflection Utilization
Load Combination number* Governing criteria Length Limit
No. [mm] [%]
[mm]
1 016-SLS Relative (Beam) 650.00 L/200 -0.07 0.00
2 016-SLS Relative (Beam) 900.00 L/200 0.01 0.00
3 016-SLS Relative (Beam) 650.00 L/200 -0.00 0.00
4 016-SLS Relative (Beam) 424.26 L/200 -0.03 0.00
5 016-SLS Relative (Beam) 424.26 L/200 0.03 0.00
*016-SLS: SW + Live + Snow + Wind (-x). Respective Combination Equation: 1.00 * LC1 + 1.00 * 0.60 * LC9
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 19 / 24
Version: 1.13.1
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 20 / 24
Version: 1.13.1
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 21 / 24
Version: 1.13.1
5.3 Connectors
5.3.1 Overview
Connector: MT-C-LL1 OC
Fx Fy Fz Mx My Mz
Connector variant: MT-C-LL1 OC (C)
[kN] [kN] [kN] [kNm] [kNm] [kNm]
Node No. : 2
Local Forces: 2.08 0.00 -0.01 0.00 -0.00 -0.00
Resistance: 8.06 1.24 8.06 0.03 0.19 0.03
abs(Fx.ed/Fx.rd)+abs(Fy.ed/Fy.rd)+abs(Fz.ed/Fz.rd)+abs(Mx.ed/Mx.rd)+abs(
Equation:
My.ed/My.rd)+abs(Mz.ed/Mz.rd)
Utilization: 25.93 % OK
Governing Load
1.35 * LC1 + 1.50 * LC8
Combination
Connector: MT-AB A OC
Fx Fy Fz Mx My Mz
Connector variant: MT-AB A OC (C)
[kN] [kN] [kN] [kNm] [kNm] [kNm]
Node No. : 6
Local Forces: 6.81 0.00 0.00 0.00 0.00 0.00
Resistance: 7.39 0.10 0.10 0.10 0.00 0.00
Equation: ((Fx.ed^2+Fz.ed^2)^0.5)/Fx.Rd + Fy.ed/Fy.Rd + Mx.ed/Mx.rd
Utilization: 92.19 % OK
Governing Load
1.35 * LC1 + 1.50 * LC9
Combination
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 22 / 24
Version: 1.13.1
5.4 Bases
5.4.1 Overview
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 23 / 24
Version: 1.13.1
Any and all information and data contained in the Software concern solely the use of Hilti products and based on the principles, formulas and security
regulations in accordance with Hilti's technical directions and operating, mounting and assembly instructions, etc., that must be strictly complied with by
the user. All figures contained therein are average figures, and therefore use-specific tests are to be conducted prior to using the relevant Hilti product.
The results of the calculations carried out by means of the Software are based essentially on the data you put in. Therefore, you bear the sole
responsibility for the absence of errors, the completeness and the relevance of the data to be put in by you. Moreover, you bear sole responsibility for
having the results of the calculation checked and cleared by an expert, particularly with regard to compliance with applicable norms and permits, prior
to using them for your specific facility. The Software servers only as an aid to interpret norms and permits without any guarantee as to the absence of
errors, the correctness and relevance ot the results or suitability for a specific application.
You must take all necessary and reasonable steps to prevent or limit damage caused by the Software. In particular, you must arrange for the regular
backup of programs and, if applicable, carry out the updates of that you are using the current and thus up-to-date version of the Software in each case
by carrying out manual updates via the Hilti Website. Hilti will not be liable for consequences, such as the recovery of lost or damaged data or
programs, arising from a culpable breach of duty by you.
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 24 / 24
DUCT 550x500 H 1675
Project: SA-13162-SF
Submitted by:
Date: 04/03/2024
Table of content
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 2 / 25
Version: 1.13.1
Support Details
Modular Support Spacing [mm] Undefined
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 3 / 25
Version: 1.13.1
Concrete
1.2 Nodes
X Y Z
No. No. Connector name Connector variant
[mm] [mm] [mm]
1 - 0.00 0.00 1675.00 MT-C-GSP T OC MT-C-GSP T OC (C_D)
2 1 0.00 0.00 0.00 MT-B-GS T OC MT-B-GS T OC (C_MT-80)
3 2 900.00 0.00 0.00 MT-B-GS T OC MT-B-GS T OC (C_MT-80)
4 - 900.00 0.00 1675.00 MT-C-GSP T OC MT-C-GSP T OC (C_D)
5 3 350.00 0.00 0.00 MT-B-GS AB OC MT-B-GS AB OC (C)
6 - -0.00 0.00 350.00 MT-AB-G T OC MT-AB-G T OC (C_D)
7 4 550.00 0.00 0.00 MT-B-GS AB OC MT-B-GS AB OC (C)
8 - 900.00 0.00 350.00 MT-AB-G T OC MT-AB-G T OC (C_D)
1.3 Members
Spring Constants
Releases
Member Translational Rotational
No. Cu,x Cu,y Cu,z Cφx Cφy Cφz
Ux Uy Uz φx φy φz
[kN/m] [kN/m] [kN/m] [kNm/Rad] [kNm/Rad] [kNm/Rad]
4 no no no no yes yes - - - - 0.000 0.000
4 no no no no yes yes - - - - 0.000 0.000
5 no no no no yes yes - - - - 0.000 0.000
5 no no no no yes yes - - - - 0.000 0.000
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 4 / 25
Version: 1.13.1
1.6 Gliders
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 5 / 25
Version: 1.13.1
2 Part list
2.1 Members
Quantity Weight
Position Item Number Description
[-] [kg]
6 2272100 Baseplate MT-B-GS T OC 2 4.33
8 2332787 Baseplate MT-B-GS AB OC 2 3.30
Quantity Weight
Position Item Number Description
[-] [kg]
4 2272074 Connector MT-C-GSP T OC plate 4 1.73
10 2272116 Angle brace MT-AB-G T OC adjustable 4 1.39
2.4 Other
Quantity Weight
Position Item Number Description
[-] [kg]
5 2272084 Thread forming bolt MT-TFB OC 52 1.48
7 2105870 Stud anchor HST3-R M12x115 40/20 4 0.41
9 2018429 Anchor rod HIT-Z-R M12x105 4 0.41
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 6 / 25
Version: 1.13.1
3 Load Types
3. Loads
Custom loads
Position Fx Fy Fz Mx My Mz
Load No. Load Type Members
[mm] [kN] [kN] [kN] [kNm] [kNm] [kNm]
1 Design 1 175.00 0.00 0.00 -0.49 0.00 0.00 0.00
2 Design 1 725.00 0.00 0.00 -0.49 0.00 0.00 0.00
3 Design 1 450.00 0.00 0.00 -0.25 0.00 0.00 0.00
4 Wind (+x) 1 450.00 2.77 -0.00 -0.00 -0.00 -0.00 -0.00
5 Wind (-x) 1 450.00 -2.77 -0.00 -0.00 -0.00 -0.00 -0.00
6 Self Weight Support 1 0.00 0.00 0.00 -0.01 0.00 0.00 0.00
7 Self Weight Support 2 0.00 0.00 0.00 -0.02 0.00 0.00 0.00
8 Self Weight Support 3 0.00 0.00 0.00 -0.02 0.00 0.00 0.00
9 Self Weight Support 1 900.00 0.00 0.00 -0.01 0.00 0.00 0.00
10 Self Weight Support 4 0.00 0.00 0.00 -0.02 0.00 0.00 0.00
11 Self Weight Support 2 350.00 0.00 0.00 -0.01 0.00 0.00 0.00
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 7 / 25
Version: 1.13.1
Start End
Fx Fy Fz Mx My Mz
Load No. Load Type Members Position Position
[kN/m] [kN/m] [kN/m] [kNm/m] [kNm/m] [kNm/m]
[mm] [mm]
14 Self Weight Support 1 0.00 900.00 0.00 0.00 -0.04 0.00 0.00 0.00
15 Self Weight Support 2 0.00 1675.00 0.00 0.00 -0.06 0.00 0.00 0.00
16 Self Weight Support 3 0.00 1675.00 0.00 0.00 -0.06 0.00 0.00 0.00
17 Self Weight Support 4 0.00 494.97 0.00 0.00 -0.04 0.00 0.00 0.00
18 Self Weight Support 5 0.00 494.97 0.00 0.00 -0.04 0.00 0.00 0.00
7 Design Permanent ☑
8 Wind (+x) Variable ☐
9 Wind (-x) Variable ☐
1 Self Weight Support Permanent ☑
☑All loads in these load cases are converted to seismic in +/-X, +/-Y and +/-Z
☐Loads not considered for seismic load conversion
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 8 / 25
Version: 1.13.1
4 Load Combinations
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 9 / 25
Version: 1.13.1
5 Results
5.1.3 Members
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 10 / 25
Version: 1.13.1
5.2 Members
Iω M Wy Wz Wy
[mm⁶] [kg/m] [mm³] [mm³] [mm³]
2039000.00 3.91 -6349.48 -6349.48 -6349.48
Iω M Wy Wz Wy
[mm⁶] [kg/m] [mm³] [mm³] [mm³]
40950000.00 12.12 -17594.40 -9801.32 -17594.40
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 11 / 25
Version: 1.13.1
5.2.2.1 Overview
*007b-ULS: SW_sup + Wind (-x). Respective Combination Equation: 1.35 * LC1 + 1.50 * LC9
*006b-ULS: SW_sup + Wind (+x). Respective Combination Equation: 1.35 * LC1 + 1.50 * LC8
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 12 / 25
Version: 1.13.1
Beam No. 1
Beam No. 2
Beam No. 3
Beam No. 4
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 13 / 25
Version: 1.13.1
Beam No. 5
*007b-ULS: SW_sup + Wind (-x). Respective Combination Equation: 1.35 * LC1 + 1.50 * LC9
*006b-ULS: SW_sup + Wind (+x). Respective Combination Equation: 1.35 * LC1 + 1.50 * LC8
Normal load
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 14 / 25
Version: 1.13.1
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 15 / 25
Version: 1.13.1
Torsion around X
Moment around Y
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 16 / 25
Version: 1.13.1
Moment around Z
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 17 / 25
Version: 1.13.1
Buckling ratio
Criteria
☑Maximum Allowable Deflection (Beam) L/200
☑Maximum Allowable Deflection (Cantilever)L/150
- Maximum Deflection (Absolute) -
☑No Deflection checks calculated for 1.50mm
Overview
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 18 / 25
Version: 1.13.1
Results
Reference
Member Max deflection Utilization
Load Combination number* Governing criteria Length Limit
No. [mm] [%]
[mm]
1 016-SLS Relative (Beam) 900.00 L/200 0.02 0.00
2 006-SLS Relative(Cantilever) 1325.00 L/150 4.20 47.60
3 007-SLS Relative(Cantilever) 1325.00 L/150 4.20 47.60
4 016-SLS Relative (Beam) 494.97 L/200 -0.04 0.00
5 016-SLS Relative (Beam) 494.97 L/200 0.04 0.00
*016-SLS: SW + Live + Snow + Wind (-x). Respective Combination Equation: 1.00 * LC1 + 1.00 * 0.60 * LC9
*006-SLS: SW + Wind (+x). Respective Combination Equation: 1.00 * LC1 + 1.00 * LC8
*007-SLS: SW + Wind (-x). Respective Combination Equation: 1.00 * LC1 + 1.00 * LC9
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 19 / 25
Version: 1.13.1
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 20 / 25
Version: 1.13.1
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 21 / 25
Version: 1.13.1
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 22 / 25
Version: 1.13.1
5.3 Connectors
5.3.1 Overview
Connector: MT-C-GSP T OC
Fx Fy Fz Mx My Mz
Connector variant: MT-C-GSP T OC (C_D)
[kN] [kN] [kN] [kNm] [kNm] [kNm]
Node No. : 1
Local Forces: -2.08 0.00 2.15 0.00 0.96 0.00
Resistance: 69.99 8.88 10.65 0.40 1.25 0.57
abs(Fx.ed/Fx.rd)+abs(Fy.ed/Fy.rd)+abs(Fz.ed/Fz.rd)+abs(Mx.ed/Mx.rd)+abs(
Equation:
My.ed/My.rd)+abs(Mz.ed/Mz.rd)
Utilization: 99.87 % OK
Governing Load
1.35 * LC1 + 1.50 * LC9
Combination
Connector: MT-AB-G T OC
Fx Fy Fz Mx My Mz
Connector variant: MT-AB-G T OC (C_D)
[kN] [kN] [kN] [kNm] [kNm] [kNm]
Node No. : 6
Local Forces: 10.83 -0.01 0.00 0.00 0.00 -0.00
Resistance: 32.03 6.44 1.83
Equation: (( Fx.ed^2 + Fy.ed^2 )^0.5)/Fx.rd + Fz.ed / Fz.rd+Mx.ed/Mx.rd
Utilization: 33.82 % OK
Governing Load
1.35 * LC1 + 1.50 * LC9
Combination
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 23 / 25
Version: 1.13.1
5.4 Bases
5.4.1 Overview
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 24 / 25
Version: 1.13.1
Any and all information and data contained in the Software concern solely the use of Hilti products and based on the principles, formulas and security
regulations in accordance with Hilti's technical directions and operating, mounting and assembly instructions, etc., that must be strictly complied with by
the user. All figures contained therein are average figures, and therefore use-specific tests are to be conducted prior to using the relevant Hilti product.
The results of the calculations carried out by means of the Software are based essentially on the data you put in. Therefore, you bear the sole
responsibility for the absence of errors, the completeness and the relevance of the data to be put in by you. Moreover, you bear sole responsibility for
having the results of the calculation checked and cleared by an expert, particularly with regard to compliance with applicable norms and permits, prior
to using them for your specific facility. The Software servers only as an aid to interpret norms and permits without any guarantee as to the absence of
errors, the correctness and relevance ot the results or suitability for a specific application.
You must take all necessary and reasonable steps to prevent or limit damage caused by the Software. In particular, you must arrange for the regular
backup of programs and, if applicable, carry out the updates of that you are using the current and thus up-to-date version of the Software in each case
by carrying out manual updates via the Hilti Website. Hilti will not be liable for consequences, such as the recovery of lost or damaged data or
programs, arising from a culpable breach of duty by you.
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 25 / 25
DUCT 600x600 H 300
Project: SA-13162-SF
Submitted by:
Date: 04/03/2024
Table of content
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 2 / 24
Version: 1.13.1
Support Details
Modular Support Spacing [mm] Undefined
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 3 / 24
Version: 1.13.1
Concrete
1.2 Nodes
X Y Z
No. No. Connector name Connector variant
[mm] [mm] [mm]
1 1 0.00 0.00 0.00 MT-B-O2 OC MT-B-O2 OC (C)
2 - 0.00 0.00 300.00 MT-C-LL1 OC MT-C-LL1 OC (C)
3 - 950.00 0.00 300.00 MT-C-LL1 OC MT-C-LL1 OC (C)
4 2 950.00 0.00 0.00 MT-B-O2 OC MT-B-O2 OC (C)
5 3 270.00 0.00 0.00 MT-AB A OC MT-AB A OC (C)
6 - 0.00 0.00 270.00 MT-AB A OC MT-AB A OC (C)
7 4 680.00 0.00 0.00 MT-AB A OC MT-AB A OC (C)
8 - 950.00 0.00 270.00 MT-AB A OC MT-AB A OC (C)
1.3 Members
Spring Constants
Releases
Member Translational Rotational
No. Cu,x Cu,y Cu,z Cφx Cφy Cφz
Ux Uy Uz φx φy φz
[kN/m] [kN/m] [kN/m] [kNm/Rad] [kNm/Rad] [kNm/Rad]
2 no no no no yes yes - - - - 0.001 0.001
2 no no no no yes yes - - - - 0.001 0.001
4 no no no no yes yes - - - - 0.000 0.000
4 no no no no yes yes - - - - 0.000 0.000
5 no no no no yes yes - - - - 0.000 0.000
5 no no no no yes yes - - - - 0.000 0.000
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 4 / 24
Version: 1.13.1
1.6 Gliders
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 5 / 24
Version: 1.13.1
2 Part list
2.1 Members
Quantity Weight
Position Item Number Description
[-] [kg]
4 2272096 2-hole Baseplate MT-B-O2 OC 2 2.05
9 2346396 Angle brace MT-AB A OC set adjustable 4 1.77
Quantity Weight
Position Item Number Description
[-] [kg]
8 2272049 Angle connector MT-C-LL1 OC 2 0.67
9 2346396 Angle brace MT-AB A OC set adjustable 4 1.77
2.4 Other
Quantity Weight
Position Item Number Description
[-] [kg]
5 2273256 Hexagon bolt MT-TLB OC 12 0.30
6 2272082 Twist-Lock MT-TL M10 OC 12 0.42
7 2105870 Stud anchor HST3-R M12x115 40/20 8 0.81
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 6 / 24
Version: 1.13.1
3 Load Types
3. Loads
Custom loads
Position Fx Fy Fz Mx My Mz
Load No. Load Type Members
[mm] [kN] [kN] [kN] [kNm] [kNm] [kNm]
1 Design 2 175.00 0.00 0.00 -0.56 0.00 0.00 0.00
2 Design 2 775.00 0.00 0.00 -0.56 0.00 0.00 0.00
3 Design 2 475.00 0.00 0.00 -0.28 0.00 0.00 0.00
4 Wind (+x) 2 475.00 3.33 0.00 0.00 0.00 0.00 0.00
5 Wind (-x) 2 475.00 -3.33 -0.00 -0.00 -0.00 -0.00 -0.00
6 Self Weight Support 1 0.00 0.00 0.00 -0.01 0.00 0.00 0.00
7 Self Weight Support 1 300.00 0.00 0.00 -0.00 0.00 0.00 0.00
8 Self Weight Support 2 950.00 0.00 0.00 -0.00 0.00 0.00 0.00
9 Self Weight Support 3 300.00 0.00 0.00 -0.01 0.00 0.00 0.00
10 Self Weight Support 4 0.00 0.00 0.00 -0.00 0.00 0.00 0.00
11 Self Weight Support 1 270.00 0.00 0.00 -0.00 0.00 0.00 0.00
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 7 / 24
Version: 1.13.1
Start End
Fx Fy Fz Mx My Mz
Load No. Load Type Members Position Position
[kN/m] [kN/m] [kN/m] [kNm/m] [kNm/m] [kNm/m]
[mm] [mm]
14 Self Weight Support 1 0.00 300.00 0.00 0.00 -0.02 0.00 0.00 0.00
15 Self Weight Support 2 0.00 950.00 0.00 0.00 -0.02 0.00 0.00 0.00
16 Self Weight Support 3 0.00 300.00 0.00 0.00 -0.02 0.00 0.00 0.00
17 Self Weight Support 4 0.00 381.84 0.00 0.00 -0.02 0.00 0.00 0.00
18 Self Weight Support 5 0.00 381.84 0.00 0.00 -0.02 0.00 0.00 0.00
7 Design Permanent ☑
8 Wind (+x) Variable ☐
9 Wind (-x) Variable ☐
1 Self Weight Support Permanent ☑
☑All loads in these load cases are converted to seismic in +/-X, +/-Y and +/-Z
☐Loads not considered for seismic load conversion
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 8 / 24
Version: 1.13.1
4 Load Combinations
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 9 / 24
Version: 1.13.1
5 Results
5.1.3 Members
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 10 / 24
Version: 1.13.1
5.2 Members
Iω M Wy Wz Wy
[mm⁶] [kg/m] [mm³] [mm³] [mm³]
38410000.00 4.08 -2652.65 -3099.95 -2652.65
5.2.2.1 Overview
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 11 / 24
Version: 1.13.1
*007b-ULS: SW_sup + Wind (-x). Respective Combination Equation: 1.35 * LC1 + 1.50 * LC9
*004b-ULS: SW_sup + Design Loads. Respective Combination Equation: 1.35 * LC1 + 1.00 * LC7
*006b-ULS: SW_sup + Wind (+x). Respective Combination Equation: 1.35 * LC1 + 1.50 * LC8
Beam No. 1
Beam No. 2
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 12 / 24
Version: 1.13.1
Beam No. 3
Beam No. 4
Beam No. 5
*007b-ULS: SW_sup + Wind (-x). Respective Combination Equation: 1.35 * LC1 + 1.50 * LC9
*004b-ULS: SW_sup + Design Loads. Respective Combination Equation: 1.35 * LC1 + 1.00 * LC7
*006b-ULS: SW_sup + Wind (+x). Respective Combination Equation: 1.35 * LC1 + 1.50 * LC8
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 13 / 24
Version: 1.13.1
Normal load
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 14 / 24
Version: 1.13.1
Torsion around X
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 15 / 24
Version: 1.13.1
Moment around Y
Moment around Z
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 16 / 24
Version: 1.13.1
Buckling ratio
Criteria
☑Maximum Allowable Deflection (Beam) L/200
☑Maximum Allowable Deflection (Cantilever)L/150
- Maximum Deflection (Absolute) -
☑No Deflection checks calculated for 1.50mm
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 17 / 24
Version: 1.13.1
Overview
Results
Reference
Member Max deflection Utilization
Load Combination number* Governing criteria Length Limit
No. [mm] [%]
[mm]
1 016-SLS Relative (Beam) 300.00 L/200 -0.04 0.00
2 016-SLS Relative (Beam) 950.00 L/200 0.01 0.00
3 016-SLS Relative (Beam) 300.00 L/200 0.00 0.00
4 016-SLS Relative (Beam) 381.84 L/200 -0.02 0.00
5 016-SLS Relative (Beam) 381.84 L/200 0.02 0.00
*016-SLS: SW + Live + Snow + Wind (-x). Respective Combination Equation: 1.00 * LC1 + 1.00 * 0.60 * LC9
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 18 / 24
Version: 1.13.1
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 19 / 24
Version: 1.13.1
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 20 / 24
Version: 1.13.1
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 21 / 24
Version: 1.13.1
5.3 Connectors
5.3.1 Overview
Connector: MT-C-LL1 OC
Fx Fy Fz Mx My Mz
Connector variant: MT-C-LL1 OC (C)
[kN] [kN] [kN] [kNm] [kNm] [kNm]
Node No. : 2
Local Forces: 2.50 0.00 -0.01 0.00 -0.00 -0.00
Resistance: 8.06 1.24 8.06 0.03 0.19 0.03
abs(Fx.ed/Fx.rd)+abs(Fy.ed/Fy.rd)+abs(Fz.ed/Fz.rd)+abs(Mx.ed/Mx.rd)+abs(
Equation:
My.ed/My.rd)+abs(Mz.ed/Mz.rd)
Utilization: 31.20 % OK
Governing Load
1.35 * LC1 + 1.50 * LC8
Combination
Connector: MT-AB A OC
Fx Fy Fz Mx My Mz
Connector variant: MT-AB A OC (C)
[kN] [kN] [kN] [kNm] [kNm] [kNm]
Node No. : 6
Local Forces: -3.94 0.00 0.00 0.00 0.00 0.00
Resistance: 7.39 0.10 0.10 0.10 0.00 0.00
Equation: ((Fx.ed^2+Fz.ed^2)^0.5)/Fx.Rd + Fy.ed/Fy.Rd + Mx.ed/Mx.rd
Utilization: 53.30 % OK
Governing Load
1.35 * LC1 + 1.50 * LC8
Combination
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 22 / 24
Version: 1.13.1
5.4 Bases
5.4.1 Overview
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 23 / 24
Version: 1.13.1
Any and all information and data contained in the Software concern solely the use of Hilti products and based on the principles, formulas and security
regulations in accordance with Hilti's technical directions and operating, mounting and assembly instructions, etc., that must be strictly complied with by
the user. All figures contained therein are average figures, and therefore use-specific tests are to be conducted prior to using the relevant Hilti product.
The results of the calculations carried out by means of the Software are based essentially on the data you put in. Therefore, you bear the sole
responsibility for the absence of errors, the completeness and the relevance of the data to be put in by you. Moreover, you bear sole responsibility for
having the results of the calculation checked and cleared by an expert, particularly with regard to compliance with applicable norms and permits, prior
to using them for your specific facility. The Software servers only as an aid to interpret norms and permits without any guarantee as to the absence of
errors, the correctness and relevance ot the results or suitability for a specific application.
You must take all necessary and reasonable steps to prevent or limit damage caused by the Software. In particular, you must arrange for the regular
backup of programs and, if applicable, carry out the updates of that you are using the current and thus up-to-date version of the Software in each case
by carrying out manual updates via the Hilti Website. Hilti will not be liable for consequences, such as the recovery of lost or damaged data or
programs, arising from a culpable breach of duty by you.
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 24 / 24
DUCT 800x800 H 700
Project: SA-13162-SF
Submitted by:
Date: 04/03/2024
Table of content
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 2 / 27
Version: 1.13.1
Support Details
Modular Support Spacing [mm] Undefined
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 3 / 27
Version: 1.13.1
Concrete
1.2 Nodes
X Y Z
No. No. Connector name Connector variant
[mm] [mm] [mm]
1 1 0.00 0.00 0.00 MT-B-O2B OC MT-B-O2B OC (C)
2 - 0.00 0.00 700.00 MT-C-GS OC MT-C-GS OC (C_D)
3 - 1150.00 0.00 700.00 MT-C-GS OC MT-C-GS OC (C_D)
4 2 1150.00 0.00 0.00 MT-B-O2B OC MT-B-O2B OC (C)
5 3 350.00 0.00 0.00 MT-AB A OC MT-AB A OC (C)
6 - 0.00 0.00 350.00 MT-AB A OC MT-AB A OC (C)
7 4 800.00 0.00 0.00 MT-AB A OC MT-AB A OC (C)
8 - 1150.00 0.00 350.00 MT-AB A OC MT-AB A OC (C)
1.3 Members
Spring Constants
Releases
Member Translational Rotational
No. Cu,x Cu,y Cu,z Cφx Cφy Cφz
Ux Uy Uz φx φy φz
[kN/m] [kN/m] [kN/m] [kNm/Rad] [kNm/Rad] [kNm/Rad]
4 no no no no yes yes - - - - 0.000 0.000
4 no no no no yes yes - - - - 0.000 0.000
5 no no no no yes yes - - - - 0.000 0.000
5 no no no no yes yes - - - - 0.000 0.000
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 4 / 27
Version: 1.13.1
1.6 Gliders
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 5 / 27
Version: 1.13.1
2 Part list
2.1 Members
Quantity Weight
Position Item Number Description
[-] [kg]
4 2282213 2-hole Baseplate MT-B-O2B OC 2 4.14
9 2346396 Angle brace MT-AB A OC set adjustable 4 1.77
Quantity Weight
Position Item Number Description
[-] [kg]
8 2272064 Angle connector MT-C-GS OC 4 1.60
9 2346396 Angle brace MT-AB A OC set adjustable 4 1.77
2.4 Other
Quantity Weight
Position Item Number Description
[-] [kg]
5 2273256 Hexagon bolt MT-TLB OC 28 0.71
6 2272082 Twist-Lock MT-TL M10 OC 28 0.98
7 2105870 Stud anchor HST3-R M12x115 40/20 8 0.81
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 6 / 27
Version: 1.13.1
3 Load Types
3. Loads
Custom loads
Position Fx Fy Fz Mx My Mz
Load No. Load Type Members
[mm] [kN] [kN] [kN] [kNm] [kNm] [kNm]
1 Design 2 575.00 0.00 0.00 -0.44 0.00 0.00 0.00
2 Design 2 175.00 0.00 0.00 -0.89 0.00 0.00 0.00
3 Design 2 975.00 0.00 0.00 -0.89 0.00 0.00 0.00
4 Seismic (+x) 2 575.00 0.02 0.00 0.00 0.00 0.00 0.00
5 Seismic (-x) 2 575.00 -0.02 -0.00 -0.00 -0.00 -0.00 -0.00
6 Seismic (+y) 2 575.00 0.00 0.02 0.00 0.00 0.00 0.00
7 Seismic (-y) 2 575.00 -0.00 -0.02 -0.00 -0.00 -0.00 -0.00
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 7 / 27
Version: 1.13.1
Start End
Fx Fy Fz Mx My Mz
Load No. Load Type Members Position Position
[kN/m] [kN/m] [kN/m] [kNm/m] [kNm/m] [kNm/m]
[mm] [mm]
18 Self Weight Support 1 0.00 700.00 0.00 0.00 -0.04 0.00 0.00 0.00
19 Self Weight Support 2 0.00 1150.00 0.00 0.00 -0.04 0.00 0.00 0.00
20 Self Weight Support 3 0.00 700.00 0.00 0.00 -0.04 0.00 0.00 0.00
21 Self Weight Support 4 0.00 494.97 0.00 0.00 -0.02 0.00 0.00 0.00
22 Self Weight Support 5 0.00 494.97 0.00 0.00 -0.02 0.00 0.00 0.00
7 Design Permanent ☑
8 Wind (+x) Variable ☐
9 Wind (-x) Variable ☐
1 Self Weight Support Permanent ☑
☑All loads in these load cases are converted to seismic in +/-X, +/-Y and +/-Z
☐Loads not considered for seismic load conversion
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 8 / 27
Version: 1.13.1
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 9 / 27
Version: 1.13.1
4 Load Combinations
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 11 / 27
Version: 1.13.1
5 Results
5.1.3 Members
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 12 / 27
Version: 1.13.1
5.2 Members
Iω M Wy Wz Wy
[mm⁶] [kg/m] [mm³] [mm³] [mm³]
154300000.00 8.40 -7048.65 -6199.90 -7048.65
Iω M Wy Wz Wy
[mm⁶] [kg/m] [mm³] [mm³] [mm³]
38410000.00 4.08 -2652.65 -3099.95 -2652.65
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 13 / 27
Version: 1.13.1
5.2.2.1 Overview
*007b-ULS: SW_sup + Wind (-x). Respective Combination Equation: 1.35 * LC1 + 1.50 * LC9
*006b-ULS: SW_sup + Wind (+x). Respective Combination Equation: 1.35 * LC1 + 1.50 * LC8
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 14 / 27
Version: 1.13.1
Beam No. 1
Beam No. 2
Beam No. 3
Beam No. 4
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 15 / 27
Version: 1.13.1
Beam No. 5
*007b-ULS: SW_sup + Wind (-x). Respective Combination Equation: 1.35 * LC1 + 1.50 * LC9
*006b-ULS: SW_sup + Wind (+x). Respective Combination Equation: 1.35 * LC1 + 1.50 * LC8
Normal load
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 16 / 27
Version: 1.13.1
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 17 / 27
Version: 1.13.1
Torsion around X
Moment around Y
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 18 / 27
Version: 1.13.1
Moment around Z
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 19 / 27
Version: 1.13.1
Buckling ratio
Criteria
☑Maximum Allowable Deflection (Beam) L/200
☑Maximum Allowable Deflection (Cantilever)L/150
- Maximum Deflection (Absolute) -
☑No Deflection checks calculated for 1.50mm
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 20 / 27
Version: 1.13.1
Overview
Results
Reference
Member Max deflection Utilization
Load Combination number* Governing criteria Length Limit
No. [mm] [%]
[mm]
1 016-SLS Relative (Beam) 700.00 L/200 -0.03 0.00
2 016-SLS Relative (Beam) 1150.00 L/200 0.01 0.00
3 016-SLS Relative (Beam) 700.00 L/200 -0.00 0.00
4 016-SLS Relative (Beam) 494.97 L/200 0.04 0.00
5 016-SLS Relative (Beam) 494.97 L/200 -0.05 0.00
*016-SLS: SW + Live + Snow + Wind (-x). Respective Combination Equation: 1.00 * LC1 + 1.00 * 0.60 * LC9
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 21 / 27
Version: 1.13.1
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 22 / 27
Version: 1.13.1
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 23 / 27
Version: 1.13.1
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 24 / 27
Version: 1.13.1
5.3 Connectors
5.3.1 Overview
Connector: MT-C-GS OC
Fx Fy Fz Mx My Mz
Connector variant: MT-C-GS OC (C_D)
[kN] [kN] [kN] [kNm] [kNm] [kNm]
Node No. : 2
Local Forces: -3.34 -0.00 1.00 0.00 -0.56 0.00
Resistance: 16.23 1.72 14.41 0.31 1.47 0.17
abs(Fx.ed/Fx.rd)+abs(Fy.ed/Fy.rd)+abs(Fz.ed/Fz.rd)+abs(Mx.ed/Mx.rd)+abs(
Equation:
My.ed/My.rd)+abs(Mz.ed/Mz.rd)
Utilization: 65.70 % OK
Governing Load
1.35 * LC1 + 1.50 * LC9
Combination
Connector: MT-AB A OC
Fx Fy Fz Mx My Mz
Connector variant: MT-AB A OC (C)
[kN] [kN] [kN] [kNm] [kNm] [kNm]
Node No. : 6
Local Forces: 7.18 0.00 0.00 0.00 -0.00 0.00
Resistance: 7.39 0.10 0.10 0.10 0.00 0.00
Equation: ((Fx.ed^2+Fz.ed^2)^0.5)/Fx.Rd + Fy.ed/Fy.Rd + Mx.ed/Mx.rd
Utilization: 97.10 % OK
Governing Load
1.35 * LC1 + 1.50 * LC9
Combination
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 25 / 27
Version: 1.13.1
5.4 Bases
5.4.1 Overview
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 26 / 27
Version: 1.13.1
Any and all information and data contained in the Software concern solely the use of Hilti products and based on the principles, formulas and security
regulations in accordance with Hilti's technical directions and operating, mounting and assembly instructions, etc., that must be strictly complied with by
the user. All figures contained therein are average figures, and therefore use-specific tests are to be conducted prior to using the relevant Hilti product.
The results of the calculations carried out by means of the Software are based essentially on the data you put in. Therefore, you bear the sole
responsibility for the absence of errors, the completeness and the relevance of the data to be put in by you. Moreover, you bear sole responsibility for
having the results of the calculation checked and cleared by an expert, particularly with regard to compliance with applicable norms and permits, prior
to using them for your specific facility. The Software servers only as an aid to interpret norms and permits without any guarantee as to the absence of
errors, the correctness and relevance ot the results or suitability for a specific application.
You must take all necessary and reasonable steps to prevent or limit damage caused by the Software. In particular, you must arrange for the regular
backup of programs and, if applicable, carry out the updates of that you are using the current and thus up-to-date version of the Software in each case
by carrying out manual updates via the Hilti Website. Hilti will not be liable for consequences, such as the recovery of lost or damaged data or
programs, arising from a culpable breach of duty by you.
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 27 / 27
DUCT 800x800 H 2200
Project: SA-13162-SF
Submitted by:
Date: 04/03/2024
Table of content
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 2 / 27
Version: 1.13.1
Support Details
Modular Support Spacing [mm] Undefined
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 3 / 27
Version: 1.13.1
Concrete
1.2 Nodes
X Y Z
No. No. Connector name Connector variant
[mm] [mm] [mm]
1 1 0.00 0.00 0.00 MT-B-GS T OC MT-B-GS T OC (C_MT-80)
2 - 0.00 0.00 2200.00 MT-C-GLP T A OC MT-C-GLP T A OC (C_D)
3 - 1150.00 0.00 2200.00 MT-C-GLP T A OC MT-C-GLP T A OC (C_D)
4 2 1150.00 0.00 0.00 MT-B-GS T OC MT-B-GS T OC (C_MT-80)
5 3 400.00 0.00 0.00 MT-B-GS AB OC MT-B-GS AB OC (C)
6 - 0.00 0.00 400.00 MT-AB-G T OC MT-AB-G T OC (C_D)
7 4 750.00 0.00 0.00 MT-B-GS AB OC MT-B-GS AB OC (C)
8 - 1150.00 0.00 400.00 MT-AB-G T OC MT-AB-G T OC (C_D)
1.3 Members
Spring Constants
Releases
Member Translational Rotational
No. Cu,x Cu,y Cu,z Cφx Cφy Cφz
Ux Uy Uz φx φy φz
[kN/m] [kN/m] [kN/m] [kNm/Rad] [kNm/Rad] [kNm/Rad]
4 no no no no yes yes - - - - 0.000 0.000
4 no no no no yes yes - - - - 0.000 0.000
5 no no no no yes yes - - - - 0.000 0.000
5 no no no no yes yes - - - - 0.000 0.000
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 4 / 27
Version: 1.13.1
1.6 Gliders
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 5 / 27
Version: 1.13.1
2 Part list
2.1 Members
Quantity Weight
Position Item Number Description
[-] [kg]
4 2272100 Baseplate MT-B-GS T OC 2 4.33
8 2332787 Baseplate MT-B-GS AB OC 2 3.30
Quantity Weight
Position Item Number Description
[-] [kg]
7 2332784 Connector MT-C-GLP T A OC 4 3.77
10 2272116 Angle brace MT-AB-G T OC adjustable 4 1.39
2.4 Other
Quantity Weight
Position Item Number Description
[-] [kg]
5 2272084 Thread forming bolt MT-TFB OC 84 2.39
6 2105870 Stud anchor HST3-R M12x115 40/20 4 0.41
9 2018429 Anchor rod HIT-Z-R M12x105 4 0.41
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 6 / 27
Version: 1.13.1
3 Load Types
3. Loads
Custom loads
Position Fx Fy Fz Mx My Mz
Load No. Load Type Members
[mm] [kN] [kN] [kN] [kNm] [kNm] [kNm]
1 Design 2 175.00 0.00 0.00 -0.89 0.00 0.00 0.00
2 Design 2 975.00 0.00 0.00 -0.89 0.00 0.00 0.00
3 Design 2 575.00 0.00 0.00 -0.44 0.00 0.00 0.00
4 Wind (+x) 2 575.00 4.44 -0.00 -0.00 -0.00 -0.00 -0.00
5 Wind (-x) 2 575.00 -4.44 -0.00 -0.00 -0.00 -0.00 -0.00
6 Seismic (+x) 2 575.00 0.02 0.00 0.00 0.00 0.00 0.00
7 Seismic (-x) 2 575.00 -0.02 -0.00 -0.00 -0.00 -0.00 -0.00
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 7 / 27
Version: 1.13.1
Start End
Fx Fy Fz Mx My Mz
Load No. Load Type Members Position Position
[kN/m] [kN/m] [kN/m] [kNm/m] [kNm/m] [kNm/m]
[mm] [mm]
18 Self Weight Support 1 0.00 2200.00 0.00 0.00 -0.06 0.00 0.00 0.00
19 Self Weight Support 2 0.00 1150.00 0.00 0.00 -0.06 0.00 0.00 0.00
20 Self Weight Support 3 0.00 2200.00 0.00 0.00 -0.06 0.00 0.00 0.00
21 Self Weight Support 4 0.00 565.69 0.00 0.00 -0.04 0.00 0.00 0.00
22 Self Weight Support 5 0.00 565.69 0.00 0.00 -0.04 0.00 0.00 0.00
7 Design Permanent ☑
8 Wind (+x) Variable ☐
9 Wind (-x) Variable ☐
1 Self Weight Support Permanent ☑
☑All loads in these load cases are converted to seismic in +/-X, +/-Y and +/-Z
☐Loads not considered for seismic load conversion
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 8 / 27
Version: 1.13.1
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 9 / 27
Version: 1.13.1
4 Load Combinations
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 11 / 27
Version: 1.13.1
5 Results
5.1.3 Members
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 12 / 27
Version: 1.13.1
5.2 Members
Iω M Wy Wz Wy
[mm⁶] [kg/m] [mm³] [mm³] [mm³]
40950000.00 12.12 -17594.40 -9801.32 -17594.40
Iω M Wy Wz Wy
[mm⁶] [kg/m] [mm³] [mm³] [mm³]
2039000.00 7.82 -6349.48 -6349.48 -6349.48
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 13 / 27
Version: 1.13.1
5.2.2.1 Overview
*007b-ULS: SW_sup + Wind (-x). Respective Combination Equation: 1.35 * LC1 + 1.50 * LC9
*006b-ULS: SW_sup + Wind (+x). Respective Combination Equation: 1.35 * LC1 + 1.50 * LC8
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 14 / 27
Version: 1.13.1
Beam No. 1
Beam No. 2
Beam No. 3
Beam No. 4
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 15 / 27
Version: 1.13.1
Beam No. 5
*007b-ULS: SW_sup + Wind (-x). Respective Combination Equation: 1.35 * LC1 + 1.50 * LC9
*006b-ULS: SW_sup + Wind (+x). Respective Combination Equation: 1.35 * LC1 + 1.50 * LC8
Normal load
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 16 / 27
Version: 1.13.1
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 17 / 27
Version: 1.13.1
Torsion around X
Moment around Y
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 18 / 27
Version: 1.13.1
Moment around Z
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 19 / 27
Version: 1.13.1
Buckling ratio
Criteria
☑Maximum Allowable Deflection (Beam) L/200
☑Maximum Allowable Deflection (Cantilever)L/150
- Maximum Deflection (Absolute) -
☑No Deflection checks calculated for 1.50mm
Overview
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 20 / 27
Version: 1.13.1
Results
Reference
Member Max deflection Utilization
Load Combination number* Governing criteria Length Limit
No. [mm] [%]
[mm]
1 006-SLS Relative(Cantilever) 1800.00 L/150 -9.67 80.56
2 016-SLS Relative (Beam) 1150.00 L/200 0.05 0.00
3 007-SLS Relative(Cantilever) 1800.00 L/150 9.67 80.56
4 016-SLS Relative (Beam) 565.69 L/200 -0.08 0.00
5 016-SLS Relative (Beam) 565.69 L/200 0.07 0.00
*006-SLS: SW + Wind (+x). Respective Combination Equation: 1.00 * LC1 + 1.00 * LC8
*016-SLS: SW + Live + Snow + Wind (-x). Respective Combination Equation: 1.00 * LC1 + 1.00 * 0.60 * LC9
*007-SLS: SW + Wind (-x). Respective Combination Equation: 1.00 * LC1 + 1.00 * LC9
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 21 / 27
Version: 1.13.1
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 22 / 27
Version: 1.13.1
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 23 / 27
Version: 1.13.1
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 24 / 27
Version: 1.13.1
5.3 Connectors
5.3.1 Overview
Connector: MT-C-GLP T A OC
Fx Fy Fz Mx My Mz
Connector variant: MT-C-GLP T A OC (C_D)
[kN] [kN] [kN] [kNm] [kNm] [kNm]
Node No. : 2
Local Forces: -3.33 -0.00 5.15 0.00 -2.94 0.00
Resistance: 99.18 6.50 37.07 1.55 3.83 2.71
abs(Fx.ed/Fx.rd)+abs(Fy.ed/Fy.rd)+abs(Fz.ed/Fz.rd)+abs(Mx.ed/Mx.rd)+abs(
Equation:
My.ed/My.rd)+abs(Mz.ed/Mz.rd)
Utilization: 93.96 % OK
Governing Load
1.35 * LC1 + 1.50 * LC9
Combination
Connector: MT-AB-G T OC
Fx Fy Fz Mx My Mz
Connector variant: MT-AB-G T OC (C_D)
[kN] [kN] [kN] [kNm] [kNm] [kNm]
Node No. : 6
Local Forces: 17.23 -0.01 0.00 0.00 0.00 0.00
Resistance: 32.03 6.44 1.83
Equation: (( Fx.ed^2 + Fy.ed^2 )^0.5)/Fx.rd + Fz.ed / Fz.rd+Mx.ed/Mx.rd
Utilization: 53.80 % OK
Governing Load
1.35 * LC1 + 1.50 * LC9
Combination
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 25 / 27
Version: 1.13.1
5.4 Bases
5.4.1 Overview
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 26 / 27
Version: 1.13.1
Any and all information and data contained in the Software concern solely the use of Hilti products and based on the principles, formulas and security
regulations in accordance with Hilti's technical directions and operating, mounting and assembly instructions, etc., that must be strictly complied with by
the user. All figures contained therein are average figures, and therefore use-specific tests are to be conducted prior to using the relevant Hilti product.
The results of the calculations carried out by means of the Software are based essentially on the data you put in. Therefore, you bear the sole
responsibility for the absence of errors, the completeness and the relevance of the data to be put in by you. Moreover, you bear sole responsibility for
having the results of the calculation checked and cleared by an expert, particularly with regard to compliance with applicable norms and permits, prior
to using them for your specific facility. The Software servers only as an aid to interpret norms and permits without any guarantee as to the absence of
errors, the correctness and relevance ot the results or suitability for a specific application.
You must take all necessary and reasonable steps to prevent or limit damage caused by the Software. In particular, you must arrange for the regular
backup of programs and, if applicable, carry out the updates of that you are using the current and thus up-to-date version of the Software in each case
by carrying out manual updates via the Hilti Website. Hilti will not be liable for consequences, such as the recovery of lost or damaged data or
programs, arising from a culpable breach of duty by you.
Data and results must be checked for agreement with existing conditions and for plausibility. Changes may be necessary.
Copyright (c) Hilti AG 2010, FL-9494 Schaan 27 / 27