Professional Documents
Culture Documents
The terms in this list are used in the meaning of the picture
PLAN = show the plan of structures
SHEAR FORCE DIAGRAM [ Fy] = show Each shear force in vertical direction(same as local axis Y direction of member ) of member sees
BENDING MOMENT DIAGRAM [ Mz] = show Each bending moment about the majoir axis(same as local axis about Z direction of member) of member sees
Displacements [ DL+OP] in Y DIR = show Each the dispalcements in vertical direction(same as Y Gobal axis) of member sees for load combinations of
DL (structure selfweight+ super imposed dead load + opearting of piping loads)
Displacements [ DL+OP] in Z DIR = show Each the dispalcements in horizontal direction(same as Z Gobal axis) of member sees for load combinations of
DL (structure selfweight+ super imposed dead load + opearting of piping loads)
Displacements [ DL+OP] in X DIR = show Each the dispalcements in horizontal direction(same as X Gobal axis) of member sees for load combinations of
DL (structure selfweight+ super imposed dead load + opearting of piping loads)
AXIL FORCE DIAGRAM [DL+ OP] = show Each the axial force of member sees for load combinations of
DL (structure selfweight+ super imposed dead load + opearting of piping loads)
REACTIONS [ DL+OP] , IN Y DIR = show Each the support reactions (the vertical forces only same as Y Gobal axis ) sees for load combinations of
DL (structure selfweight+ super imposed dead load + opearting of piping loads)
Ratio = show dividing result of the maximum stress and the allowable stress of each beam sees.
the maximum stress was calculated from service load combination [ more than 1.0 is fails but less than 1.0 is Pass ]
Beam Force Detail Summary = The summation of the maximum force in all 6 directions of the beam which
beams have been grouped for the purpose connection design in the next step
H‐400x400x13x21, service load , [ MSJ1 ] = This is the summation of the H beam size 400x400x13x21 mm which it's calculated from
the service load combination for the purpose connection design of moment joint splice plate type that MSJ1 name
Max Von Mis = The maximum Von Mises stress used for check the local elements of structure fail
The terms in this list are used in the meaning of the analysis and steel design from Staad pro program
UNIT METER KG = We set the unit for force is kiligram and for the length is meter under this declare message
UNIT INCHES KIP = We set the unit for force is kilopounds and for the length is inches under this declare message
START GROUP DEFINITION = This declare is for purpose we create the group of memebr for find the maximum forces that represent from each groups
actual the groups is for Connection design .
START MY MZ ( sub title of member release) = members which release both the bending moment about Y dir (local axis) and Z dir (local axis) of the one end (start node) of beam
END MY MZ ( sub title of member release) = members which release both the bending moment about Y dir (local axis) and Z dir (local axis) of the one end (end node) of beam
START MPZ 0.85 ( sub title of member release) = members which release only the bending moment 85% about Z dir (local axis) of the one end (end node) of beam
JOINT LOAD = applied load at node of member ( this load is point load only)
458 FY ‐1.42288 the vetical load [ Fy , Gobal axis] is 1.4288 KIPS on node that number 458
JOINT LOAD = applied load at node of member ( this load is point load only) on node that number 458
499 FX ‐0.0544385 FY 0.28685 FZ 0.07575 in X dir is ‐0.0544385 KIPS , in Y dir is 0.28685 KIPS ,and in Z dir is 0.07575 KIPS that the direction are coressponding to Gobal axis
MEMBER LOAD = applied load on member ( such as uniform distribution load or point load )
826 CON GY ‐2.883413 47.64 the vetical load [ Gy , Gobal axis] is 47.64 KIPS at 2.833 meter of member that number 826
REFERENCE LOAD = the combination load of ( LOAD 4 x load factor = 1.0 ) + ( LOAD 5 x load factor =1.0 )+ ( LOAD 6 x load factor =1.0)
R4 1.0 R5 1.0 R6 1.0
LOAD COMB 10 DL + OP = this service load combination in No 10 which it's compose of structure selfweight+ super imposed deadload plus operation piping load
1 1.0 3 1.0 that it was calculate from the primary load No. 1.0 x load factor =1.0 + the primary load No. 3 x load factor = 1.0
Remark the service load combination used for pipling or soils design and steel design and check service states limited
LOAD COMB 12 1.2DL + 1.6OP = this factored load combination in No. 12 which it's compose of structure selfweight+ super imposed deadload plus operation piping load
1 1.2 3 1.6 that it was calculate from the primary load No. 1 x load factor =1.2 + the primary load No. 3 x load factor = 1.6
Remark the factored load combination used for anchorage to concrete design and RC designand check strength states limited
PARAMETER 1 = For set the all parameter that use for AISC CODE steel structure design
CODE AISC
FU 4E+07 MEMB 18 21 ..., etc = applied the ultimate strength 4x10^7 kg/m^2 to member number 18, number 21 .,, etc ( All of member was assigned )
FYLD 2.501E+07 MEMB 18 21 ..., etc = applied the yeilding strength 2.501x10^7 kg/m^2 to member number 18, number 21 .,, etc ( All of member was assigned )
UNB 8.8 MEMB 18 21 ..., etc = applied the unbrace length support at the bottom flange of member that it's 8.8 meter to member number 18, number 21 .,, etc
UNT 8.8 MEMB 18 21 ..., etc = applied the unbrace length support at the Top flange of member that it's 8.8 meter to member number 18, number 21 .,, etc
CB 1.2 MEMB 18 21 ..., etc = applied the lateral torsion buckling factor of beam that it's a value 1.2 to member number 18, number 21 .,, etc
KY 0.8 MEMB 18 = applied the column buckling factor about Y direction (same as local member cross section) that it's a value 0.8 to member number 18
KZ 0.8 MEMB 18 = applied the column buckling factor about Z direction (same as local member cross section) that it's a value 0.8 to member number 18
TRACK 2 ALL = applied the maximum data detail for steel design to all member that we want to shown in this report