Professional Documents
Culture Documents
TM
QUALCOMM CDMA TECHNOLOGIES H T T P : / / W W W. C D M AT E C H . C O M ENABLING THE FUTURE OF COMMUNICATIONS
MSM6500 ™ CHIPSET SOLUTION
Q U A L C O M M , I N C O R P O R AT E D CDMA TECHNOLOGIES 5775 MOREHOUSE DRIVE SAN DIEGO, CA 92121 T (858) 658-5005 F (858) 658-1556 cdma-technologies@qualcomm.com
QUALCOMM CDMA TECHNOLOGIES H T T P : / / W W W. C D M AT E C H . C O M ENABLING THE FUTURE OF COMMUNICATIONS TM
The Mobile Station (MS) collects measurements from the GPS MSM6500 Device Features
constellation and the cellular/PCS network, and then sends the The MSM6500 system solution consists of the MSM6500, RFL6000,
information to the Position Determination Entity (PDE), which RFR6000, RFT6100 or RTR6300, PM6650, DMSS™ (Dual-Mode
optimizes the position location calculation based on existing Subscriber Software™) and SURF6500™ platform, and features:
information. gpsOne technology will enable consumer-priced,
position-capable CDMA handsets. The chipset block diagram • CDMA2000 1xEV-DO (IS-856) support
illustrates the baseline architecture for the MSM6500 and • CDMA2000 1X (IS-2000)
CDMA/GPS terminal devices. • GSM/GPRS support, 3GPP compliant Revision 99 class B,
multi-slot class 10 data services
The MSM6500 chipset and system software is also capable of • Receive diversity on CDMA2000 1X and 1xEV-DO systems
operating in a standalone gpsOne mode, in which the handset acts • High-performance ARM926EJ-S microprocessor core with
as a GPS receiver. memory management unit (MMU)
PM6650
Color LCD, Spkr, Vibrator,
Power-on
Keypad,
LED Drivers
Camera Flash,
Drivers Sequencing I
USB TCXO Cntrl, RUIM,
Transceiver Sleep Osc, SD Card
RTC
Bluetooth RF SMPS Vregs SMPS Vreg Vregs for RUIM,
For MSM For USB/OTG USB, WLAN,
MEM, PA
MPP Smart
Digital/Analog Thermal Charging
I/Os Control System
MSM6500
Mobile Station Modem
PC UART1 Bluetooth RFR6000 RFL6000
Connectivity Baseband
UART2/UIM Processor
Test/Debug PCS I/Q D
System Mixer Rx I
UART3/UIM USB PCS P
On-The-Go L
I/Q CELL I/Q SAW E
ARM926EJ-S TM HK ADCs Low-pass Mixer Rx X
Filters CELL E
R
NAND Flash SAW
NOR Flash External Memory Enhanced SBI
Interface MPEG4 LO Generation
LP-SDRAM Control and SBI
Encoder Distribution
PSRAN
ETM9
Rx
Camera Diversity Rx Rx PLL Rx VCO
Interface Engine ADCs GPS
Color LCD
Interface GPS I/Q GPS
LCD
1 2 3 gpsOne xxx6RFR RFR6000 Mixer
GPS
BPF
4 5 6
Keypad 7 Enhanced Processor LNA
8 9 PCS I/Q
General- RF
* 0 # Mixer Rx
Ringer Purpose Interface PCS
Interface
CDMA
General-Purpose Interface Bus Processor I/Q I/Q CELL I/Q SAW
SAW PCS
RFT6100 PA
MSM6500 Chipset Architecture Configured for 1X/1xEV-DO with Receive Dual Diversity
3
• Java hardware acceleration through Jazelle core for faster Java- • Integrated USB OTG controller to enable direct connectivity to USB
based games and other applets enabled accessories, such as printers, digital cameras, keyboards
• Advanced QDSP4000 DSP cores and CD-ROMs
• Integrated MPEG-4 decoder/encoder for streaming Video-On- • Direct interface support for cost-effective low-voltage, high-
Demand (VOD) and video-mail applications performance memory such as low-power SDRAM, page-mode
• Integrated JPEG decoder/encoder for camera-based applications NAND Flash, page and burst-mode NOR Flash among others
• Integrated 2D/3D graphics accelerator engine for a more enhanced • Direct interface with advanced color LCD controllers and displays
user experience • Direct interface to digital camera module
• Integrated Bluetooth baseband processor for wireless connectivity to • Voice Recognition (PureVoice VR™), including speaker-independent
peripherals digit dialing
• Integrated gpsOne functionality that is capable of operating in • Multimedia Card (MMC) support
standalone mode • Removable Universal Identity Module (R-UIM) card interface
• Integrated wideband stereo codec for digital audio applications • Multi-band operation; Cellular, PCS, EGSM, and DCS frequency
• Qtunes audio decoder bands along with GPS and Bluetooth technology
• Support for multiple vocoders; EVRC, and 13K QCELP®, Adaptive • Support for QCT’s BREWapi platform
Multiple Rate (AMR), Full Rate (FR), Enhanced FR (EFR), and Half • Advanced 409-pin 0.5 mm pitch CSP packaging technology
Rate (HR) (14 mm x 14 mm)
PM6650
Color LCD, Spkr, Vibrator,
Keypad, Power-on
Camera Flash, Sequencing
LED Drivers Drivers
MSM6500
Mobile Station Modem RFL
RFR6000
6000
PC UART1 Bluetooth
Connectivity Baseband GPS
UART2/UIM Processor BPF
Test/Debug GPS I/Q
System
UART3/UIM
RFR6000 Mixer GPS
USB LNA
On-The-Go PCS I/Q
Mixer Rx
ARM926EJ-S TM PCS
HK ADCs I/Q SAW
NAND Flash I/Q CELL I/Q
External Low-pass Mixer Rx
NOR Flash Memory Filters CELL
LP-SDRAM Interface Rx Rx
PSRAN SAW
Diversity ADCs
ETM9 Engine
SBI C P
Control E C
SBI LO Generation
and L S
Camera GPS
Interface Control
VCO
Distribution RFL6000 L DDI
D I
LCD
PLL D U PPL
Color U P L
1 2 3 LCD Interface VCTCXO Rx
P L E EX
L E XE
4 5 6 gpsOne 19.2 MHz VCO E X E
Keypad 7 8 9 Enhanced Processor X E RR
E R
* 0 # General- R
Ringer Purpose RF
Interface CDMA Interface RTR6300 UHF Rx
General-Purpose Interface Bus Processor PLL
IxEV-DO Rx I
Rx
Processor GSM GSM
QDSP4000 LPF LNA
Launchpad Rx
GSM/GPRS SAW
Applications Processor Tx DACs
Rx Q
Demodulator Rx Switchplexer
GSM DCS
Second LPF LNA
Speaker SAW
MP3
Wideband Enhanced
MPEG4
UHF LO DCS GSM
Stereo
Encoder Rx\Tx Generator
CODEC PA PA
PLL
SBI
External Mode Selection MODE Select Tx
Interface Tx I CELL CELL
PA DAC LPF
SAW CELL
Tx
MMC MMC Controller Game Engine Modulator Tx
Tx Q PCS PCS
R-UIM R-UIM Controller Java Accelerator LPF LPF
SAW PCS
MSM6500 Chipset Architecture Configured for Receive Dual Diversity 1X/1xEV-DO with Dual-Band GSM/GPRS
QUALCOMM CDMA TECHNOLOGIES H T T P : / / W W W. C D M AT E C H . C O M ENABLING THE FUTURE OF COMMUNICATIONS TM
RFL6000 Device Description Included on the chip is the GPS LNA as well as the entire GPS VCO,
Integrated into the RFL6000 device are two low- including resonant components. The Rx PLL, which resides on the
noise amplifiers (LNAs): a cellular LNA and PCS transmit companion chipset (the RFT6100 device), is switched
LNA. Both LNAs utilize three gain settings that between the GPS Voltage Control Oscillator (VCO) and the external
are programmable through the SBI. Rx VCO.
Operating modes—sleep, Rx, and Rx/Tx—as Extension of standby time is achieved by selective circuit power
well as LNA bias currents are all automatically adjusted via software down, gain control and bias current. These features, along with all
to minimize DC power consumption. Depending on handset status, radioOne chipset functions, are controlled by the MSM.
the LNA bias current adjusts to meet RF performance requirements
with minimal power consumption. The RFR6000 device is designed to operate with 2.7 to 3.1 V power
supplies and is compatible with single-cell Li-Ion batteries.
The RFL6000 device is fabricated using SiGe BiCMOS process, Compatibility to the lower voltage (1.8 to 3.1 V) is assured when
which is suited for high performance RF circuits, and is packaged in VDDM is connected to the MSM pad voltage.
a very small 16-pin bump chip carrier (16-pin BCC++).
The RFR6000 chip is fabricated using a SiGe BiCMOS process,
RFL6000 Device Features which provides high-frequency, high-precision analog circuits as well
• Reduction in component count, space and cost via radioOne as low-power CMOS functions. Package type is 40 BCCP, which
chipset that eliminates receiver and transmitter IF includes a large ground slug for improved grounding, mechanical
• Two integrated LNAs with programmable gain steps strength and thermal conductivity.
• Cellular LNA supports CDMA and FM modes
– Cellular bands of operation in China, Japan, Korea, and the RFR6000 Device Features
United States • Compatibility with QCT’s radioOne Zero IF chipset that eliminates
– Three CDMA gain settings the entire IF and reduces component count and space
– Two FM gain settings • Single- or multi-band operation (cellular, PCS, GPS)
• PCS LNA supports PCS CDMA operation • Single- or multimode operation: cellular CDMA, PCS CDMA,
– PCS bands of operation in China, Korea, and the United States cellular FM and GPS
– Three CDMA gain settings • Full downconversion—RF to baseband
• Programmable mode and bias control to reduce DC power • Receive path circuitry
consumption – GPS LNA
• High reverse isolation – Stepped gain control
• Efficient three-line SBI – Three-quadrature down converter
• Low power consumption – Band-specific low-pass filter
• Small package: 16-pin BCC++ (4 mm x 4 mm) • Baseband amplifiers with DC offset adjustment
• SiGe BiCMOS process fabrication • Need for only one single-band external VCO (Rx VCO) for all
CDMA bands of operation for entire radioOne chipset.
RFR6000 Device Description • Includes entire on-chip GPS VCO—including resonant circuit
The RFR6000 device is the radioOne zero IF • Individual circuit power on/off controls
downconverter. The device has three mixers • Power reduction feature control and extended handset standby
which, when combined with the RFL6000 time
device, provide full RF-to-baseband – Selective circuit power-down
downconversion for the cellular, PCS and GPS – Gain and bias controls
bands. The LO generation block produces all LO • Low power supply voltage (2.7 to 3.1 V), low power dissipation
signals, and only one external single-band VCO is required for all – Compatible with lower MSM voltage (1.8 to 3.0 Vdd)
CDMA frequency bands of operation. • Small, thermally efficient package (40 BCC++)
7
powerOne Series PM6650 Device Description • SMPS voltage control for optimized PA Vdd and bias control for
The MSM6500 device also interfaces directly with maximum talk-time performance
the first in QCT’s new powerOne series power • SMPS voltage generation for white LEDs used for Color LCD
management ICs, the PM6650 device. The PM6650 backlighting
solution provides battery management and charging • USB OTG transceiver included
functions, including a USB charging option, and • Configurable Multi-Purpose Pins (MPPs) for digital or analog I/O utility
voltage regulation for the various MSM power functions such as general-purpose LED drivers, USIM or SD-Card-
regimes, the radioOne chipset and all other MSM-supported peripheral level translation, programmable resistors or digital switches
features. Exceptional power savings are realized through the use of a • High-current LED driver for Camera Flash application
switch-mode power supply (SMPS) from the PM6650 device to regulate • Speaker driver with programmable gain, turn-on time, and muting;
the MSM’s core voltage. All voltages generated for the MSM and single-ended or differential operation (drives external 8-ohm
radioOne RF chips are optimized for handset system control with the speakers with volume-controlled 500 mW)
MSM6500 system software. • Real-time clock for tracking time, calendar functions, programmed
durations and generating associated alarms
The PM6650 chip offers unparalleled integration of power • TCXO Control provides warm-up, synchronization, and buffering of
management functions for CDMA terminals, affording a tremendous the TCXO signal for optimal QPH/catnap timing and maximum
savings in size and BOM for handset design. Integrated features standby-time performance
include a color LCD backlight driver, USB OTG transceiver, R-UIM and • Automated power-on recovery from sudden momentary power loss
SD Card interface, PA bias control, speaker driver, real-time clock, • Support for coin cell back-up battery (including charging)
TCXO control, and various general housekeeping and interface • 84 BCCS dual-row bump chip carrier package (7 mm x 7 mm)
functions, making the PM6650 chip the ideal power management
solution for feature-rich terminals. QUALCOMM's Complete Solution — Our Commitment to our Partners
QUALCOMM CDMA Technologies is enabling the future of
PM6650 Features communications. We work closely with our manufacturer and operator
• Complete battery management, voltage regulation, general partners to develop solutions that meet market needs today and provide
housekeeping and user-interface functions for UMTS terminals the technology foundation for the wireless communications of tomorrow.
• Compatible with QUALCOMM’s radioOne ZIF chipset and all MSM- Our world-class CDMA engineers create detailed reference designs to
supported peripheral features accelerate testing and deployment for our partners. And our chipsets
• Trickle, fast, constant voltage and pulsed charging modes for the and system software are fully integrated and able to bring advanced
main battery, with current monitoring for over-current protection features and functionality to today's wireless devices. With QUALCOMM
• Available USB charging option with automatic charging source CDMA Technologies, manufacturers and operators can offer
selection sophisticated wireless solutions that succeed in the global marketplace.
• Complex power management, including MSM power-on sequencing
and control, and dynamic voltage scaling for maximum power savings
• Switch-mode power supply (SMPS), which provides high-efficiency
voltage regulation for the MSM core, and 1.8 V high-speed external
bus interface and memory circuits
QUALCOMM CDMA TECHNOLOGIES H T T P : / / W W W. C D M AT E C H . C O M ENABLING THE FUTURE OF COMMUNICATIONS TM
MSM6500 ™ CHIPSET SOLUTION
Q U A L C O M M , I N C O R P O R AT E D CDMA TECHNOLOGIES 5775 MOREHOUSE DRIVE SAN DIEGO, CA 92121 T (858) 658-5005 F (858) 658-1556 cdma-technologies@qualcomm.com