Professional Documents
Culture Documents
MD Elements
MD Elements
What is the property of matter that causes it to resist any change in its motion
or state of rest?
A. Momentum
B. Inertia
C. Kinetic Energy
D. Section modulus
3. In manufacturing, what is the operation of cutting out flat area to some desired
shape and is usually the first step in a series of operation?
A. Turning
B. Facing
C. Blanking
D. Finishing
4. What is the algebraic difference between a size and the corresponding basic
size?
A. Tolerance
B. Deviation
C. Allowance
D. Lim
5. It is a computational method used for solving complex shapes, such as those
found in machinery; replaces the complex shape with a set of simple elements
interconnected at a finite set of a specific purpose. What is this computational
method?
A. Finite element analysis
B. Fault free analysis
C. Numerical method of analysis
D. Synthesis
8. When preparing to tap a hole, the size of the drill will be:
A. equal to the size of the tap
B. smaller than the size of the tap
C. larger than the size of the tap
D. none of the above
14. The cylinder of piston type steam engine are counter bored to:
A. give a larger head clearance
B. prevent piston rings from wearing a groove in the cylinder at the end of
the stroke
C. give a larger volumetric clearance
D. prevent piston rings from slipping on the piston
15. Which of the following is not true for an instant center or centro of planar
linkages?
A. Centro is a point common to two bodies having the same velocity in
each.
B. Centro is a point in one body about which another body actually turns.
C. Centro is a point in one body about which another body tends to turn.
D. Centro is a point in one body about which another body does not rotate.
16. Twist drills are usually considered suitable machining holes having a length less
than
A. two times their diameter
B. ten times their diameter
C. five times their diameter
D. twenty times their diameter
19. Manufactured from aluminum oxide have the same expected life as carbide
tools but can operate at speeds from two to three times higher. They operate
below 1100°C.
A. Sintered carbides
B. Ceramic tools
C. Diamonds
D. Cast nonferrous
20. Which of the following contains tungsten or chromium and retains its hardness
up to approximately 1100°F, a property known as red hardness
A. Ceramic tool
B. Diamonds
C. High speed steel
D. Carbon tool steel
21. How do you call a statistical data used to identify the most likely failure modes?
A. Finite element analysis
B. Fault free analysis
C. Failure analysis
D. Random analysis
22. Which of the following are the compositions of stainless steel 302?
A. 18 % chromium and 8 % nickel
B. 18 % nickel and 8 % chromium
C. 18 % chromium and 8 % phosphor bronze
D. 18 % bronze and 8 % vanadium
23. This alloy (nickel, iron, chromium, cobalt is a non-magnetic, corrosion resistant
material suitable for sub-zero temperatures and temperatures up to about 750
degrees F., provided that torsional stresses are kept below 75,000 pounds per
square inch. It is precipitation-hardened to produce harnesses of 48 to 50
Rockwell C and is used in watch and instrument springs.
A. Elinvar
B. Inconel
C. Monel
D. Dynavar
24. What is the difference of the values of the Wahl factor and the Bergstrasser
factor, in percentage?
A. 1 %
B. Greater than 1 %
C. Less than 1 %
D. 0.5 %
25. Which of the following threads are used for power screw?
A. Square thread, Acme thread, & Unified thread
B. Square thread, Unified thread, & Acme thread
C. Acme thread, Unified thread, & Buttress thread
D. Square thread, Acme thread, & Buttress thread
26. When two elastic bodies collide, which of the following laws can be used to
solve for the resulting velocity?
A. Avogadro’s law
B. Conservation of momentum and conservation of energy
C. Dalton’s law of partial pressure
D. Conservation of energy
27. Which of the following process affects the changes in properties of materials?
A. Shaping
B. Sintering
C. Hardening
D. Anodizing
30. Which of the following chisels would be used for cutting oil grooves?
A. diamond-point chisel
B. round-nose chisel
C. cold chisel
D. hot chisel
31. After a piece of piece of pipe has been cut, the hole is cleaned out with a:
A. piper reamer
B. pipe taper
C. pipe cleaner
D. hole cleaner
34. A piece of mild steel held against an emery wheel will give off:
A. bright shiny sparks
B. light straw colored sparks
C. no sparks
D. green sparks
39. The maximum-strain theory which apples only in elastic range of stresses are
also known as _____
A. Hooke’s Law
B. Stress-strain Theory
C. Saint Venant’s Theory
D. Cataligno’s Theory
40. Which of the following is the statement of how the total moment is derived
from a number of forces acting simultaneously at a point?
A. Goodman’s theorem
B. Soderberg’s theorem
C. Varignon’s theorem
D. Cataligno’s theorem
41. These springs are made from one or more flat strips of brass, bronze, steel or
other materials loaded as cantilevers or simple beam.
A. Torsion springs
B. Garter springs
C. Leaf springs
D. Drawbar springs
43. For an American Standard Screw Threads, what does 6-32 UNC designate?
A. Size 6, 32 threads per inch, coarse thread
B. 6 inches’ basic diameter, 32 threads per inch, coarse thread
C. Size 6, 32 threads per inch, fine thread
D. 32 inches’ basic diameter, 6 threads per inch, coarse thread
44. Which of the following gases is typically used in nitriding process of surface
hardening?
A. Nitrogen gas
B. Ammonia gas
C. Carbon dioxide
D. Hydrogen gas
45. This is the trade name for a patented alloy made up chiefly of cobalt,
chromium, and tungsten in varying proportions. What is this trade name?
A. Stellite
B. Stainless steel
C. Carboloy
D. Copper
46. It is called as the transformation of concepts and ideas into useful machinery.
What is this?
A. Design
B. Analysis
C. Synthesis
D. Theorem
47. What do you call a material having different properties in all directions at point
in solid?
A. Isotropic material
B. Orthotropic material
C. Anisotropic material
D. Ceramic material
48. What do you call a type of bolt threaded on both ends and can be used
where a through bolt is impossible?
A. Coupling bolt
B. Stud bolt
C. Machine bolt
D. Carriage bolt
53. If a piston ring is to be made 1/64” larger in diameter per inch diameter of the
cylinder which it is to fit, the required diameter for a piston ring to fit an 8”
cylinder will be:
A. 8 – ¼”
B. 8 – 3/16”
C. 8 - 1/8”
D. 8 – 5/32”
54. Twist drills are usually considered suitable machining holes having a length less
than:
A. two times their diameter
B. five times their diameter
C. ten times their diameter
D. twenty times their diameter
55. If muriatic acid is used as a flux, the soldered area must be cleaned thoroughly
afterwards to prevent:
A. anyone touching it from getting burned
B. remaining acid from eating the metal
C. the acid from evaporating the solder disintegrating
D. none of the above
57. What is the lip clearance angle of twist drill for generated work?
A. 3 – 6°
B. 12 – 15°
C. 8 – 10°
D. 18 – 22°
59. An instrument for measuring the degree of surface roughness in micro inches.
A. Caliper
B. Profilometer
C. Micrometer
D. Sclerescope
60. Is the process of cold works where a limited amount of material, resulted to a
higher strength and it leaves a surface under compressive stress?
A. surface finishing
B. surfacing
C. smoothing
D. surface rolling