Professional Documents
Culture Documents
Tabela de Pressão Da Transmissão
Tabela de Pressão Da Transmissão
Página 1 de 10
Fechar o SIS
Tela anterior
Teste e Ajustes
IT28G Integrated Toolcarrier and 924G, 924GZ and 928G Wheel Loaders
Número de Mídia -RENR6425-03 Data de Publicação -01/05/2003 Data de Atualização -29/05/2003
i01779978
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
2. Place the transmission direction and speed control lever (if equipped) in the NEUTRAL position and
in any speed position. Shift the transmission direction control switch (if equipped) to the NEUTRAL
position.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis... 15/04/2011
924G 924Gz Wheel Loader RBB00001-UP (MACHINE) POWERED BY 3056E E... Página 2 de 10
7. Allow only authorized personnel on the machine. Keep unauthorized personnel off the machine and in
clear sight of the operator.
Note: All tests and all adjustments must be made while the transmission oil is at normal operating
temperature.
NOTICE
Do not connect or disconnect hose fittings to or from the quick
disconnect nipples when there is pressure in the system. This will
prevent damage to the seals that are in the fitting.
Table 1
Required Tools
Part Number Description Qty
1U-5481 Pressure Gauge Group 1
1U-5482 Pressure Adapter Group 1
Test Procedures
Test for the Transmission Clutch Pressure
Use the following procedure to check the pressure of the direction clutch oil and the speed clutch oil.
Modulating valve for clutch 5 (5) (third speed and fourth speed)
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis... 15/04/2011
924G 924Gz Wheel Loader RBB00001-UP (MACHINE) POWERED BY 3056E E... Página 3 de 10
Illustration 1 g00913305
Illustration 2 g00913306
1. Install the correct hose assembly from the 1U-5482 Pressure Adapter Group on pressure tap (1)
through pressure tap (6). Attach the opposite end of the hose assembly to the 0 to 3400 kPa (0 to 580
psi) pressure gauge in the 1U-5481 Pressure Gauge Group .
2. Engage the parking brake. Shift the transmission direction and speed control lever to the NEUTRAL
position. Shift the transmission direction control switch to the NEUTRAL position (if equipped). Start
the engine and operate the engine at low idle.
3. Ensure that the transmission neutralizer override is enabled. The transmission neutralizer override is
enabled when the transmission neutralizer override switch is illuminated.
Note: The machine can drive through the service brakes when the machine is at high idle.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis... 15/04/2011
924G 924Gz Wheel Loader RBB00001-UP (MACHINE) POWERED BY 3056E E... Página 4 de 10
5. Depress the brake pedal and hold the brake pedal. Release the parking brake. Make sure that the
machine is in first speed. Watch the pressure gauges. Shift the transmission direction and speed
control lever from the NEUTRAL position to the FORWARD position. Increase the engine speed to
high idle. Make sure that the transmission oil is at normal operating temperature. The needle on the
pressure gauge for clutch 1 should rise. The needle on the pressure gauge for clutch 6 should rise. The
pressure readings must be within the values in Table 3.
With the transmission in the FORWARD position, shift through the remaining forward speeds and
note the clutch pressures for each speed. Return to the FIRST SPEED position. Use the transmission
direction and speed control lever. The pressure reading for each energized clutch must be within the
values in Table 3. This checks the pressure of all the speed clutches.
6. Perform Step 5 for all reverse speeds. The same pressure levels should be noted in all reverse speeds.
7. Perform 5 and 6 with the engine at low idle. The same pressures should be observed. If the pressures
are lower, there is a leak in the transmission control system.
Table 2
Clutch 1
(forward X X X
low)
Clutch 2
(forward X
high)
Clutch 3
X X X
(reverse)
Clutch 4
(second X X
speed)
Clutch 5
(third speed
X X X X
and fourth
speed)
Clutch 6
(first speed) X X
Table 3
Transmission Pressures
Pressure Tap Specification Actual Pressure
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis... 15/04/2011
924G 924Gz Wheel Loader RBB00001-UP (MACHINE) POWERED BY 3056E E... Página 5 de 10
The transmission clutches should have the same clutch pressure. If the pressure readings for all of the
transmission clutches are not within the values that are in Table 3, the transmission relief valve may need to
be adjusted. Refer to "Adjustment for the Transmission Pump Pressure" for the proper adjustment
procedure. If one of the transmission clutch pressures are not within the specification, check that the
modulating valve for that clutch is operating correctly.
Use the following procedure to check the pressure of the transmission lubrication oil.
Illustration 3 g00889657
The inlet for the transmission lubrication oil is located on the right side of the machine.
2. Install the correct hose assembly from the 1U-5482 Pressure Adapter Group on pressure tap (7).
Attach the opposite end of the hose assembly to the 0 to 400 kPa (0 to 58 psi) pressure gauge in the
1U-5481 Pressure Gauge Group .
3. Start the engine and operate the engine at high idle. Observe the pressure gauge. With the oil at
normal operating temperature, the lubrication oil pressure must be within the values in Table 3.
Table 4
Transmission Pressure
Pressure Tap Specification Actual Pressure
Transmission lubrication
170 ± 34 kPa (25 ± 5 psi)
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis... 15/04/2011
924G 924Gz Wheel Loader RBB00001-UP (MACHINE) POWERED BY 3056E E... Página 6 de 10
Illustration 4 g00913310
1. Install the correct hose assembly from the 1U-5482 Pressure Adapter Group on pressure tap (8) .
Attach the opposite end of the hose assembly to the 0 to 3400 kPa (0 to 580 psi) pressure gauge in the
1U-5481 Pressure Gauge Group .
2. Start the engine and operate the engine at high idle. Observe the pressure gauge. With the oil at
normal operating temperature, the transmission oil pump pressure must be within the values in Table
5.
Table 5
Transmission Pressure
Pressure Tap Specification Actual Pressure
Illustration 5 g00913312
The transmission relief valve (10) is located below the modulating valves.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis... 15/04/2011
924G 924Gz Wheel Loader RBB00001-UP (MACHINE) POWERED BY 3056E E... Página 7 de 10
Illustration 6 g00889597
If the transmission oil pump pressure at pressure tap (8) is not within the values in Table 6, adjust the spring
of the transmission relief valve (10). Use the following procedure.
Turning the adjustment screw clockwise increases pump pressure. Turning the adjustment screw
counterclockwise decreases pump pressure. One full turn of the adjustment screw changes pump
pressure 160 kPa (23 psi).
4. Check the transmission oil pump pressure again. Make sure that the transmission oil pump pressure is
within the value in Table 6.
Table 6
Transmission Pressure
Pressure Tap Specification Actual Pressure
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis... 15/04/2011
924G 924Gz Wheel Loader RBB00001-UP (MACHINE) POWERED BY 3056E E... Página 8 de 10
Illustration 7 g00913315
Illustration 8 g00913316
Pressure tap (13) is located on the transmission relief valve. The transmission relief valve is located below
the modulating valves.
1. Install the correct hose assembly from the 1U-5482 Pressure Adapter Group on pressure tap (13).
Attach the opposite end of the hose assembly to the 0 to 2000 kPa (0 to 290 psi) pressure gauge in the
1U-5481 Pressure Gauge Group .
2. Start the engine and operate the engine at high idle. Observe the pressure gauge. With the oil at
normal operating temperature, the torque converter inlet pressure must be below the values in Table 7.
Table 7
Transmission Pressure
Pressure Tap Specification Actual Pressure
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis... 15/04/2011
924G 924Gz Wheel Loader RBB00001-UP (MACHINE) POWERED BY 3056E E... Página 9 de 10
Illustration 9 g00910058
Illustration 10 g00913318
1. Install the correct hose assembly from the 1U-5482 Pressure Adapter Group on pressure tap (14).
Attach the opposite end of the hose assembly to the 0 to 2000 kPa (0 to 290 psi) pressure gauge in the
1U-5481 Pressure Gauge Group .
2. Start the engine and operate the engine at high idle. Observe the pressure gauge. With the oil at
normal operating temperature, the torque converter inlet pressure must be within the values in Table 8.
Table 8
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis... 15/04/2011
924G 924Gz Wheel Loader RBB00001-UP (MACHINE) POWERED BY 3056E... Página 10 de 10
Transmission Pressure
Pressure Tap Specification Actual Pressure
Transmission Pressures
Table 9
Transmission Pressure
Actual Pressure
Pressure Tap Specification
Modulating valve for clutch 1 (forward low) 2400 ± 170 kPa (350 ± 25
psi)
Modulating valve for clutch 2 (forward high) 2400 ± 170 kPa (350 ± 25
psi)
Modulating valve for clutch 4 (second speed) 2400 ± 170 kPa (350 ± 25
psi)
Modulating valve for clutch 6 (first speed) 2400 ± 170 kPa (350 ± 25
psi)
Transmission lubrication
170 ± 34 kPa (25 ± 5 psi)
Direitos Autorais 1993 - 2011 Caterpillar Inc. Fri Apr 15 12:22:34 UTC-0300 2011
Todos os Direitos Reservados.
Rede Particular Para Licenciados SIS.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis... 15/04/2011