Professional Documents
Culture Documents
CTP Mantenimiento
CTP Mantenimiento
Output Device
653-01284B-EN Rev A
Internal 732-00108B-EN Rev A
Operational Lights and What They Mean
Error Light Flashing yellow An error has occurred and the job is suspended.
Imaging Plates Using Different Workflows
The output device receives the job in the Kodak Print Console
1 In the Kodak® Prinergy® workflow management software,
software.
click OK to submit the file.
Prinergy
Prinergy Evo
The output device receives the job in the Print Console software.
Imaging a Plate
1 Ensure the device is ready. 2 In the workflow software, Ensure that the correct plate is available 3 Remove the slip sheet.
submit the file. for loading.
4 Position plate on the load ramp. 5 Lower the plate gently until it touches 6 Align the plate on the load ramp.
the registration pins.
Media alignment
label
Plate imaging.
Operator Maintenance and Operations
Operations
OFF
Plate roller * 9 Clean Monthly
Every three
Edge detection strip * 10 Clean
months
Note: This document is not intended as a substitute for the Trendsetter 400/800 Help or the Trendsetter Output
Devices Safety Guide. See these documents for a more detailed explanation. Software may appear differently,
depending on the version of Print Console in use.
Replacing the Air Supply Filters
1 Turn off the compressed air.
Warning: Remove air pressure from the Air supply filter kit
device before replacing an air filter. For full (part number 332-00003)
details, see the Trendsetter 400/800 Help
and the Trendsetter Output Devices Safety Guide.
0 psi
7 Turn on the
compressed air.
80 psi
Cleaning Inside the Output Device
1 To open the front panel:
In the Print Console software, Rotate the two latches and lift
a unlock the front panel. b Warning: To avoid the risk of electrical
the front panel. shock, do not allow liquids to run freely into
the output device.
Replacing the Intake Air Filter
1 Remove the fan box panel: 2 Remove the old intake air filter from
inside the fan box panel.
Push the upper corners of Lift the fan box panel
a b
the fan box panel in until you up and out.
hear both latches click.
3 Install the new intake air filter. 5 Replace the fan box panel:
Clean the intake air filter frame. 4
Lift the fan box panel and lower it Push the upper corners of the fan
a b
onto the locating pins. box panel in until you hear both
latches click.
Locating pin
Replacing the Universal Debris Removal Cabinet Filter
1 Ensure that your output device is not 2 Open the cabinet lid. Press down with the 3 Remove the particulate filter. Lift the 4 Place the used filter in a bag for
imaging a plate or film and that the heel of your hand while releasing the latch filter straight up using the handle. disposal. A bag is provided with
UDRC power indicator light is off. with your fingers. the replacement filter.
Best Practice: Always have a spare Caution: The black hole in the top
UDRC filter on hand for when the filter of the filter has a very sharp edge.
needs to be replaced. Do not touch the hole when lifting
the filter to avoid cutting your fingers.
5 Clean the interior of the UDRC filter compartment. 6 Install the particulate filter in the filter 7 Close the cabinet lid. Press down on 8 In the Print Console software, click Eject and
Vacuum the dust collected around the tube in the compartment with the gasket facing up. the lid, until you hear the latch click. follow the Print Console instructions.
center of the inner lid. Remove all filter residue from
the inner lid and interior surface.
Gasket
Removing a Flyoff
Caution: Wear protective gloves when
To open the front panel: handling plates.
1
The device suspends activity. In the Print Console Rotate the two latches and lift Caution: If you have an implanted cardiac
a b
software, unlock the the front panel. pacemaker, ensure that magnetic clamps are
front panel. kept more than 7 cm (2.75 in.) away from the
pacemaker.
2 Rotate the drum to expose the 3 Slide the trailing-edge clamps 4 Fold over the corners of 5 Press the leading-edge clamps 6 Clean out any debris left
trailing-edge clamps. off the plate. the plate. to free the plate. behind.
In the Print Console software, click Reposition the trailing-edge clamps: Close the front panel and the 10 In the Print Console software, click
7 8 9
Media Removed. Slide the trailing-edge clamps into top panel. Resume.
a Align the trailing-edge clamps. b
position.
Eastman Kodak Company
343 State Street
Rochester, NY 4650 U.S.A.