Professional Documents
Culture Documents
Mechanics of Materials: Pure Bending
Mechanics of Materials: Pure Bending
CHAPTER MECHANICS OF
4 MATERIALS
Ferdinand P. Beer
E. Russell Johnston, Jr.
John T. DeWolf
Lecture Notes:
Pure Bending
J. Walt Oler
Texas Tech University
Pure Bending
Pure Bending Example 4.03
Other Loading Types Reinforced Concrete Beams
Symmetric Member in Pure Bending Sample Problem 4.4
Bending Deformations Stress Concentrations
Strain Due to Bending Plastic Deformations
Beam Section Properties Members Made of an Elastoplastic Material
Properties of American Standard Shapes Plastic Deformations of Members With a Single
Deformations in a Transverse Cross Section Plane of S...
Sample Problem 4.2 Residual Stresses
Bending of Members Made of Several Example 4.05, 4.06
Materials Eccentric Axial Loading in a Plane of Symmetry
Example 4.03 Example 4.07
Reinforced Concrete Beams Sample Problem 4.8
Sample Problem 4.4 Unsymmetric Bending
Stress Concentrations Example 4.08
Plastic Deformations General Case of Eccentric Axial Loading
Members Made of an Elastoplastic Material
Pure Bending
Bending Deformations
Beam with a plane of symmetry in pure
bending:
• member remains symmetric
• bends uniformly to form a circular arc
• cross-sectional plane passes through arc center
and remains planar
• length of top decreases and length of bottom
increases
• a neutral surface must exist that is parallel to the
upper and lower surfaces and for which the length
does not change
• stresses and strains are negative (compressive)
above the neutral plane and positive (tension)
below it
© 2002 The McGraw-Hill Companies, Inc. All rights reserved. 4-6
Edition
Third
MECHANICS OF MATERIALS Beer • Johnston • DeWolf
3
yA 114 10
Y 38 mm
A 3000
I x I A d 2 12
1 bh3 A d 2
1 90 203 1800 12 2 1 30 403 1200 182
12 12
I 868 103 mm 868 10-9 m 4
Example 4.03
SOLUTION:
• Transform the bar to an equivalent cross
section made entirely of brass
Example 4.03
SOLUTION:
• Transform the bar to an equivalent cross section
made entirely of brass.
Es 29 106 psi
n 1.933
Eb 15 106 psi
bT 0.4 in 1.933 0.75 in 0.4 in 2.25 in
nAs 8.06 24 85 in 4.95 in 2
2
Stress Concentrations
Plastic Deformations
• For any member subjected to pure bending
y
x m strain varies linearly across the section
c
• If the member is made of a linearly elastic material,
the neutral axis passes through the section centroid
My
and x
I
Plastic Deformations
• When the maximum stress is equal to the ultimate
strength of the material, failure occurs and the
corresponding moment MU is referred to as the
ultimate bending moment.
Residual Stresses
• Plastic zones develop in a member made of an
elastoplastic material if the bending moment is
large enough.
• Radius of curvature:
• Maximum elastic moment: Y 240 10 6 Pa
Y
200 109 Pa
E
I 2 2 2 3 3 2
bc 3 50 10 m 60 10 m
c 3 1.2 10 3
120 10 6 m3 y
Y Y
I
M Y Y 120 10 6 m3 240 MPa
c yY 40 10 3 m
28.8 kN m 33.3 m
Y 1.2 10 3
225 m
Example 4.07
SOLUTION:
• Find the equivalent centric load and
bending moment
Example 4.07
• Normal stress due to a
centric load
A c 2 0.25 in 2
0.1963 in 2
P 160 lb
0
A 0.1963 in 2
815 psi
Example 4.07
SOLUTION:
• Determine an equivalent centric load and
bending moment.
Unsymmetric Bending
• Analysis of pure bending has been limited
to members subjected to bending couples
acting in a plane of symmetry.
Unsymmetric Bending
• 0 Fx x dA m dA
y
c
or 0 y dA
y
Wish to determine the conditions under • M M z m dA
y
c
which the neutral axis of a cross section σ I
of arbitrary shape coincides with the or M m I I z moment of inertia
c
axis of the couple as shown. defines stress distribution
Unsymmetric Bending
Superposition is applied to determine stresses in
the most general case of unsymmetric bending.
• Resolve the couple vector into components along
the principle centroidal axes.
M z M cos M y M sin
Example 4.08
SOLUTION:
• Resolve the couple vector into
components along the principle
centroidal axes and calculate the
corresponding maximum stresses.
M z M cos M y M sin
Example 4.08
• Resolve the couple vector into components and calculate
the corresponding maximum stresses.
M z 1600 lb in cos 30 1386 lb in
M y 1600 lb in sin 30 800 lb in
1 1.5 in 3.5 in 3 5.359 in 4
I z 12
1 3.5 in 1.5 in 3 0.9844 in 4
I y 12
The largest tensile stress due to M z occurs along AB
M z y 1386 lb in 1.75 in
1 4
452.6 psi
Iz 5.359 in
The largest tensile stress due to M z occurs along AD
2
M yz
800 lb in 0.75 in 609.5 psi
Iy 0.9844 in 4
Example 4.08
72.4o