Professional Documents
Culture Documents
Pressure Vessel Code Asme Section Viii Division 1
Pressure Vessel Code Asme Section Viii Division 1
Organisation
General, Construction General, Material,
Similar to Division 2
Type & Material U, UG, Design, Fabrication
KG, KM, KD, KF,
UW, UF, UB, UCS, and others AG, AM,
KR, KE, KT, KS
UNF, UCI, UCD, UHT, AD, AF, AR, AI, AT,
ULT AS
Welding and Different types with butt Extensive Butt welds and
Fabrication welds and others use/requirement of extensive use of
butt welds and full other construction
penetration welds methods such as
including non threaded, layered,
pressure wire-wound,
attachment welds interlocking
stripwound and
others
Symbols :
t = min. required thickness
P = internal design pressure
R = inside radius of shell
S = max. allowable stress value (Sec II D)
E = joint efficiency (UW-12)
Cylindrical Shells (UG-27)
PR or SEt
t P
SE 0.6 P R 0.6t
2. Longitudinal Stress (Circumferential Joints).
t ≤ 0.5R, P ≤ 1.25SE
or
PR 2SEt
t P
2SE 0.4 P R 0.4t
Relevant when additional loadings are applicable
Thickness Calculation based on Outside
diameter(Appendix 1-1)
PR 2SEt
t or P
2 SE 0.2 P R 0.2t
Based on Outside Diameter (Appendix 1-1)
PR0 or 2 SEt
t P
2 SE 0.8 P R0 0.8t
PD 2SEt cos
t or P D 1.2t cos
2 cos ( SE 0.6 P )
t
PD or P
4 SEt cos
4 cos ( SE 0.4 P ) D 0.8t cos
t
PD0 or P
4 SEt cos
4 cos ( SE 1.4 P ) D0 2.8t cos
Formed Heads
Table 1-4.1
Values of factor K
(Use nearest Values of D/2h; Interpolation Unnecessary)
Ellipsoidal Heads (UG-32) (Appendix 1-4)
(Continued…)
t/L ≥ 0.002
Inside Depth = ¼ Inside diameter
PD 2 SEt
t or P
2 SE 0.2 P D 0.2t
t/L ≥ 0.002
PDK 2 SEt
t OR P
2 SE 0.2 P KD 0.2t
PD0 K 2SEt
t OR P
2 SE 2 P( K 0.1) KD0 2t ( K 0.1)
2
Where 1 D
K 2
6 2h
Torispherical Heads (UG-32) (Appendix 1-4)
Table 1-4.2
Values of factor M
(Use nearest Values of L/r; Interpolation Unnecessary)
Torispherical Heads (UG-32) (Appendix 1-4)
(Continued…)
t/L ≥ 0.002
Knuckle radius = 6% of inside crown radius
Inside crown radius = outside diameter of skirt
0.885PL SEt
t or P
SE 0.1P 0.885L 0.1t
Where minimum tensile strength > 70,000 psi
PLM 2 SEt
t or P
2 SE 0.2 P LM 0.2t
PL0 M 2SEt
t or P
2 SE P( M 0.2) ML0 t ( M 0.2)
1 L
Where M 3
4 r
Hemispherical Heads (UG-32) (Appendix 1-4)
t ≤ 0.356L, P≤ 0.665SE
PL 2 SEt
t or P
2 SE 0.2 P L 0.2t
20 103 0.4536
S 2
14.062 Kg / mm 2
(25.4)
Total Pressure at Bottom Tan line P = Internal Pressure + Liquid Pressure
Liquid Pressure = ρ*g*h
= 1200 x 9.81 x 4
= 47088 N/m² kg m
=47088/9.81x1000000 Kg/mm² 47088 2
m sec 2
= 0.0048 kg/mm²
so, Total Design Pressure P= 0.12+0.0048 = 0.1248 kg/mm²
Sample Problem (Continued…)
13.13 3
16.13mm
Required Thickness for Longitudinal Stress
P= 0.1248 ≤ 1.25SE=14.94 kg/mm² (So condition Satisfied)
PR 0.1248 1253
t C 3
2SE 0.4 P (2 14.062 0.85 0.4 0.1248)
6.512 3
9.512mm
Sample Problem (Continued…)
2:1 Ellipsoidal head as per UG-32 (Solution)
Design pressure P=0.12 Kg/mm²
Corroded Inside radius R=1253mm
Corrosion Allowance C= 3 mm
Joint Efficiency E=0.85
Allowable stress S= 14.062 kg/mm ² at 482°F (Sec-IID)
D 2500
Inside Depth h 3 3 628mm
4 4
1 D 1 2506 2
2
Factor K K 2 2
6 2h 6 2 628
1mm
Sample Problem (Continued…)
Required Thickness at top
PDK
t C
2 SE 0.2 P
0.12 2506 1
3
2 14.062 0.85 0.2 0.12
15.59mm
Sample Problem (Continued…)
1 L 1 2500
Factor M M 3 3
4 r
4 300
1.47 mm
Sample Problem (Continued…)
Required thickness
PL 0.1263 1253
t C 3
2 SE 0.2 P 2 14.062 0.85 0.2 0.1263
9.63mm
Design for External Pressure
and compressive stresses
Compressive forces caused by dead weight, wind, earthquake, internal
vacuum
Can cause elastic instability (buckling)
Vessel must have adequate stiffness
– Extra thickness
– Circumferential stiffening rings
ASME procedures for cylindrical shells, heads, conical sections. Function
of:
– Material
– Diameter
– Unstiffened length
– Temperature
– Thickness
Subsection B -
Requirements pertaining to methods of
Fabrication of Pressure Vessels
Part UW : Requirements for Pressure vessels fabricated
by Welding
General UW-1 to UW-3
Materials UW-5
Design UW-8 to UW-21
Fabrication UW-26 to UW-42
Inspection and Tests UW-46 to UW-53
Markings and Reports UW-60
Pressure Relief Devices UW-65
Part UF : Requirements for Pressure vessel fabricated by
Forging
Part UB : Requirements for Pressure vessel fabricated by
Brazing
Part UW
UW-2 - Service Restrictions
(a) Lethal Service
(b) Low Temperature Service
(c) Steam Service
(d) Direct fired Service
(a) Lethal Service
- Vessels with lethal substances, all butt welds shall be full radiographed.
CS/LAS vessels shall be post weld heat treated.
- It shall be responsibility of user to specify – if vessel is for lethal service.
- All “category A” joints shall be “type (1)”
- All “category B & C” joints shall be “type (1) or (2)”
- All “category D” shall be full penetration welds.
(b) Low Temperature Service
- All “category A” joints shall be “type (1)”
- All “category B” joints shall be “type (1) or (2)”
- All “category C” joints shall be full penetration welds.
- All “category D” shall be full penetration welds.
Part UW (Continued..)
UW-2 - Service Restrictions
(5) All category A and D butt welds with joint efficiency [of full
radiography]
(a) Cat. A and B butt welds of vessel sections or heads
shall be of type (1) or (2).
(b) Cat. B or C butt welds (not including those in nozzles
except as required above) which intersect Cat.A butt
welds or connect seamless vessel sections or heads
shall meet spot radiography requirement.
(7) UT may be substituted for closing seam if RT is not possible.
Part UW (Continued..)
UW-11 - Radiographic Examination
(b) Spot Radiography
- Butt weld joints of type (1) or (2) which are not required to be
fully radiographed.
-If spot radiography is specified for entire vessel, radiography is
not required of Cat B and C butt welds in nozzles that exceed
neither 10” size not 29 mm thickness
(c) No Radiography
- No radiography is required when vessel is designed for external
pressure only or where joint efficiency is as per table UW-12 (C)
Part UW (Continued..)
UW-12 - Joint Efficiency
Heads Attached to
Shells
Part UW (Continued..)
UW-13 Attachment
Detail
Heads Attached to
Shells (continued..)
Part UW (Continued..)
UW-13 Attachment
Detail
Heads Attached to
Shells (continued..)
Part UW (Continued..)
UW-13 Attachment
Detail
Attachments of
Pressure Parts to
flat plates
Part UW (Continued..)
UW-13 Attachment Detail
Attachments of Pressure Parts to flat plates (Continued..)
Part UW (Continued..)
UW-13 Attachment Detail
Pressure Parts with butt welded hubs
Part UW (Continued..)
UW-16 Nozzle welded to shells
Part UW (Continued..)
UW-16 Nozzle welded to shells (continued)
Part UW (Continued..)
UW-16 Nozzle welded to shells (continued)
Part UW (Continued..)
UW-16 Nozzle welded to shells (continued)
Subsection C -Requirements pertaining
to Classes of Materials
Part UCS
Impact Test
Exemption
Curve
Part UCS (Continued…)
Low Temperature Operations
UCS-66 -Materials
-General Notes on Assignment of Materials to Curves: