Professional Documents
Culture Documents
MANUAL
Chapter 3. Appendix
3.1 An Explanation of ICON 26
Chapter 1.
The manual is made for the CRT HELMON SERIES and DPRAM SERIES users.
And HYUNDAI ELEVATOR provides CRT program.
- People who can use software programs under the WINDOWS circumstance.
- People who can use the mouse clicking and double-clicking.
- People who can understand and hand of dialog box message
which appears when using the program.
ELMON 2000 Instruction manual
2. Introduction manual
Above screen is a page that program runs very first step. Up to disappearing
logo table form the screen, the program upload files which are necessary for
CRT to run.
This screen shows the locations of elevators in the building easily. It is usually made up of
drawing or bird's-eye view of the building.
How to use
You may see a monitoring program icon on the wallpaper of monitoring program installed
computer. When you double-click the icon, monitoring program will be run and you can see above
screen. There are use available lists on the top of the menu bar. The lists will be explained later.
When you want to shut down the program, you can use the shot down tap on the menu bar.
If you select elevator surveillance, a screen will be printed just like the above. The
picture above which is to show all the elevators(also escalators where escalators are
located), shows group(for apartments, the apartment's number) & the elevator number and
also the floor & status at the moment.
Also you can control each elevator. Regarding the elevator control, it will be explained
again further below. In the list, there is an item listed 'Return to Main Screen'. If you
select it, this function allows you to go to the main screen without exiting the elevator
surveillance screen. The icons below the function are connected directly to the function.
Thus if you click the icon, it performs the same function as selecting it from the list.
If you double click the group button from the above screen, the screen will change to
group screen. If you double click the elevator number, the screen will change to individual
screen. And, if you double click the picture image part, the screen will change to single
surveillance screen.
shows the elevator's floor location at the shows the downward movement by
moment by number picture
shows the upwards movement by picture shows the downward car status by
picture
shows the upward car status by picture shows waiting or getting on/off status
by picture
shows the elevators main power status by shows the checking of malfunctioning status
text by text
shows the automatic/manual run by text shows the parking information by text
shows the full load status by text status shows the elevator's phone and
communication by text
shows the surveillance/non-surveillance for corresponding cell phone by text
If you double click the group button from the total surveillance or individual surveillance
screen, the group surveillance screen will be printed just like the above. In the group
surveillance screen, it shows the elevators by each group and also the floor & status at the
moment. Unlike the total surveillance, it indicates according to the floor with its correct
pictures. If you double click the room number, you will go to the individual surveillance
screen. And, if you double click the total surveillance view button, you will go to the total
surveillance screen. The menu bar's and icon's function is the same as in the total
surveillance screen.
In the screen, the numbers that are vertical are for car call(the buttons that are pressed
to go to the targeted floor). If the car call button is pressed from inside the elevator, the
screen's floor number changes to green and when arrived at the targeted floor, the color
green goes away. Thus, it shows the car call's status.
shows the elevator's floor & status shows the downward movement by
together picture
shows the upwards movement by picture shows the downward car status by
picture
shows the upward car status by picture shows waiting or getting on/off status
by picture
shows the elevators main power status by shows the checking of malfunctioning status
text by text
shows the automatic/manual run by text shows the full load status by text
shows the surveillance/non-surveillance for corresponding cell phone by text
shows the elevator's phone and communication by text
If you double click the elevator number button from the total surveillance or individual
surveillance screen, the individual surveillance screen will be printed just like the above. In
the individual surveillance screen, it shows the elevators by each group and also the floor &
status at the moment. Unlike the total surveillance, it indicates according to the floor with
its correct pictures. If you double click the group button, you will go to the group
surveillance screen. And, if you double click the total surveillance view button, you will go
to the total surveillance screen. The menu bar's and icon's function is the same as in the
total surveillance screen.
In the screen, the numbers that are vertical are for car call(the buttons that are pressed
to go to the targeted floor). If the car call button is pressed from inside the elevator, the
screen's floor number changes to green and when arrived at the targeted floor, the color
green goes away. Thus, it shows the car call's status.
The triangle indicated by blue and red next to the car call is the hall call(the buttons that
are pressed outside the elevator). If you press the UP button to go up to get on the
elevator from the hall, the color changes to blue and if you press the DOWN button, it
changes to red. When arrived at the targeted floor, the color blue or red goes away.
The number pad is a function made to view the elevator's signal. From number 1 to 48
is made to save the A/S worker's A/S time defining each of the signals.
If you want use elevator's total surveillance, group/apartment's number surveillance, individual
surveillance...
--> select it from menu, tool bar, or double click the corresponding button.
If you double click the picture image on the total surveillance screen, the individual
surveillance screen will be printed just like the above. In the individual surveillance screen, it
shows the elevators by the corresponding car's number and also the floor & status at the
moment. Unlike the total surveillance, it indicates according to the floor with its correct
pictures.
In the screen, the numbers that are vertical are for car call(the buttons that are pressed
to go to the targeted floor). If the car call button is pressed from inside the elevator, the
screen's floor number changes to green and when arrived at the targeted floor, the color
green goes away. Thus, it shows the car call's status.
The triangle indicated by blue and red next to the car call is the hall call(the buttons that
are pressed outside the elevator). If you press the UP button to go up to get on the
elevator from the hall, the color changes to blue and if you press the DOWN button, it
changes to red. When arrived at the targeted floor, the color blue or red goes away.
The individual surveillance is a function only available on the total surveillance screen. It
is a function used when you don't want to go to the individual surveillance screen but
instead want to see only one car number which you pull up the above screen by double
clicking the corresponding car number's picture image. If you want to exit the above
screen, you just click on the 'X' on the upper right corner of the screen.
In case where the control command is not functioned properly, a box will pop up regarding the
reason and the check matter will go to the previous
state.
2.1.4 REPORT
Report can be shown on the screen by warning or control data and, if needed, can be
printed out by printer.
2.1.4.1 WARNING
Warning report is a data for warning occurrence detail occurred in each elevator.
Select
- Total - refer to warnings for all the
elevators.
- Elevator
Select group(apartment number) -
references the corresponding
group(apartment number).
Select elevator number - refer to the
corresponding
elevator number.
When you click on the "Inquiring" button after entering the inquiring data, the following
screen will appear.
Print Contents
Elevator number : "what group - what elevator number" or "what apartment number - what
elevator number".
Sort : Occurrence or Disfunction.
Code : corresponding set data.
Malfunctioning content : "fire, door opening, Break Error occurrence, power block, manual
run, parking run, and etc."
Occurrence Time : shows the malfunctioning time by "hour:minute:second".
Occurrence Date : shows the malfunctioning data by "year:months:day".
Button Description
Arrange by Time : shows the printed data after sorting in order of "occurrence time,
occurrence date".
Arrange by Number : shows the printed data after sorting in order of "elevator number,
occurrence time, occurrence date".
View : can view the expected print data by pages.
Print : prints the data on the current screen.
Close : Exits the current screen and returns to the MAIN program(Report's beginning
screen).
2.1.4.2 CONTROL
The control report is a data for controlling occurrence contents occurred in each elevator.
Selecting of the control inquiry
Enter the information to be found and then click the inquiry button, then the following screen
will appear.
Print Contents
Button Description
Arrange by time : Shows the output data in order of "occurrence time, occurrence date."
Arrange by an unit : Shows the output data in order of " an unit, occurrence time,
occurrence date."
Preview : The data to be printed can be viewed by pages.
Print : Print the data on the current screen.
Close : Close the current screen and return to the main program ( the intial screen of
report)
This is the function of handling by each level after received from the terminals and then
store warning or control data occurred in the elevator in the database.
Level 1 is a critical failure; therefore, the client system transfers the failure information. After
that, the client system is requested to inform A/S personnel(maintenance personnel) who is
assigned by the terminal host to notify the information immediately.
Level 2 is a critical failure; therefore, the client system transfer the failure information. After
that, the client system stores its information in the database and requests its contents
displayed on the screen.
Level 3 is a critical failure. The logger program of a terminal host displays contents of the
failure on the main screen and then stores the information in the database with animating
level 3 or warning sounds.
Level 4 is a slight failure. The logger program of a terminal host does not display the
contents of the fault on the main screen and then stores its information in the database with
animating level3 or warning sounds.
Level 5 is a very slight failure. As this will be set depending on the jobsite situation, the
failure does not be displayed. If this is in normal state, the sign indicating normal state will
be animated
instructions
First select warning menu on the main screen, then after the warning screen will pop up.
This is the automatic running program with surveillance programs.
This program does not be ended because this must always receive the failure information.
Instructions
From the main menu, choose system managing menu select changing password then you
will be able to find user reset password box.
If your password file is damaged, you will see message box and it will print out with
message. Then please contact HYUNDAI ELEVATOR.
If user wants to change user's old ID, please use following direction. At the first, input your
old ID into old ID section, then input new user ID into new ID section. He clicks change
button. (If old ID is 01-Hong, enter '01-Hong' into user ID section.)
Changing password, 1. Select user ID which wants to change password, then input current
password. 2. Input new password into new password section, input same new password to
confirmed new password section then click change password button. If you click cancel
button your password will not be changed.
2.1.7 EXIT
If you exit a surveillance program, the screen you can enter exit password will pop up. Exit
password can not be changed during elevator control. Password will
be notified to a user.
malfunctioning alert
program exit
HELMON 2000
_____________________________________________
running downward
running upward
5. paging
upward paging
downward paging
call icon
6. communication icon