Professional Documents
Culture Documents
CEILINGS
Panel Splice
Carrier Splice
® All TRAC® ceilings are designed to allow easy access. Panels or tiles may be
TRAC Ceilings 84R Curved Panel Ceiling lifted out or clipped off for maintenance or installation of concealed services.
TRAC® ceiling systems set the trend and command a very high market share
in India. The TRAC® range of metal and Glass Reinforced Gypsum ceilings
are specially designed for the Indian market, taking into account of building Cross Tee
design, construction practices and weather conditions.
ACOUSTICS
Suspended acoustical ceilings serve to provide sound absorption on the
most useful surface in a room. They help in reducing reverberant sound
intensity within a room. TRAC® ceilings are the most efficient sound
Inside Curve Outside Curve
absorbing ceilings available in the market today.
Human activity in offices and large public spaces generates noise resulting in
200F Ceiling System
reduced work efficiency. Acoustical (sound absorbing) ceiling systems help in
reducing build-up of reverberant noise because of their excellent sound
absorbing properties. This leads to a better working environment and
reduced annoyance due to high noise levels. GRG Open Cell Ceiling
1 2
NNOVATE NITIATE NTEGRATE
ACOUSTICS SOUND TRANSMISSION LOSS
Noise is major concern when designing indoor spaces. Room sound Sound transmission loss is a measurement of sound insulation between one
absorption is one of the most important factors in controlling built-up room and another. Some manufacturers provide sound transmission loss
reverberant noise and in reducing sound transmission between rooms. (attenuation) values for ceiling tiles. This information is of doubtful utility
because ceiling tiles are supported on grids and have penetrations through
When specifying the ceiling, the architect should ensure that the
them to accommodate light fittings and air conditioning diffusers. The overall
specifications incorporate acoustic performance requirements.
sound transmission loss of such a composite ceiling will be 10-20 dB lower
than the transmission loss of the ceiling panel or tile alone.
SOUND ABSORPTION
When designing for sound insulation between rooms, the partition
The sound absorbing efficiency of material is designated by its sound
separating the rooms is of major concern. To prevent flanking sound
absorption coefficient (a). This is usually measured and reported in octave
transmission through the suspended ceiling, it is important that partitions do
bands over the frequency range of 125-4000 Hz, together with the Noise
not stop at the ceiling, but are extended right up to the roof slab above. The
Reduction Coefficient (NRC), which is the average of the sound absorption
suspended ceiling should not be relied upon to give sound insulation
coefficient at 250, 500, 1000 and 2000 Hz. Sound absorption coefficient
between adjacent spaces.
data is given for all TRAC® ceilings. This enables calculation of noise
reduction or reverberation time.
The increasing use of hard finishes and stone/tile finishes in offices requires
the use of highly sound absorbent ceilings. TRAC® ceilings offer NRC values
of 0.75 upto 1.05 for different ceiling types.
Mineral Fiber Tile 0.13 0.29 0.47 0.58 0.57 0.54 0.48
GRG T 206, no holes 0.09 0.10 0.10 0.12 0.25 0.35 0.14
GRG T 206, no holes/25MW 0.20 0.40 0.55 0.10 0.21 0.50 0.32
FIRE RESISTANCE
All TRAC® ceilings provide Class 1 Surface Spread of Flame in accordance with BS 476-part 7 (1987). The materials are incombustible as per BS 476-part 4
(1970) and satisfy Class O as per BS 476-part 6 (1989).
3 4
NNOVATE NITIATE NTEGRATE
TRAC Ceilings
®
84R Interior & Exterior Ceilings
THE RIGHT CEILING FOR THE RIGHT APPLICATION DESIGN AND ENGINEERING SUPPORT 84R INTERIOR Flush join Profiles : Made of enamelled aluminium, for 100mmmodule
(16mm gap).
INTERARCH is a pioneer of coated metal architectural products in India and The Interarch Architectural Projects and Service Group (ASG) provides Material
has a consistent record of product innovation. Over the years, millions of customers with complete design, engineering, and drafting support. Suspension: By means of suspension rods and spring clips. One suspension
Panels: 84mm wide x 16mm deep, made out of 0.50mm aluminium alloy
square metres of INTERARCH architectural building products have been for every 1.5 to 2 sq.m.
ASG can help you convert your most imaginative designs into reality. Shop AA3005/3105/5052 with stove enamelled coil coated finish / 0.45
installed in India and abroad.
drawings and detailed bill of quantities are prepared for all projects to ensure galvanised steel with stove enamelled coil coated finish. Panel Span: 1.3m max. with insulation, 1.5m max. without insulation.
TRAC® ceilings are available in a wide range of panel types for decorative correct product supply and application.
(Colour according to TRAC® colour chart and availability chart) Carrier Span: 1.3m max. spacing of suspension rods.
and functional applications. TRAC® ceilings are suitable for use in interior and
exterior areas in offices, hospitals, schools, restaurants, shops, hotels, Panel length upto approx 5m Finish
airports and other buildings. TRAC® ceilings are also suitable for industrial
When perforated, hole diameters are 2mm on 5mm centres (standard) or Coil Coated: Panels will be finished on exposed side with 20 microns
use and are specially suited to aggressive environments inside factory
1mm on 2.5mm centres (microperforated), the holes representing15% of polyester coil coating over primer and on rear side with a wash coat.
buildings.
the perforated area.
16
closures with recessed or flush join profiles for 16mm gap.
84
39
32
5 À2
5
31
47
16
2.5 À1
25
84 16 32
FLUSH PROFILE
(OPTIONAL)
Material Finish
Panels: 84mm wide x 16mm deep, made out of 0.60mm aluminium alloy Coil Coated: Panels will be finished on exposed side with coil coated stove
AA 3005 / 3105 / 5052 with stove enamelled coil coated finish. enamelled PVF2 or polyurethane paint with a wash coat on the rear side.
Absorption Coefficients
1.20
1.00
Absorption Coefficient
0.80
0.60
0.40
0.20
0.00
125 250 500 1000 2000 4000 NRC
...84R perf/25mm Mineral 0.20 0.69 0.96 0.91 0.96 0.86 0.88
Wool/200mm air space
Frequency, Hz
5 6
NNOVATE NITIATE NTEGRATE
84C/184C Interior & Exterior Ceilings 150F/200F Interior & Exterior Ceilings/75C & 150C Interior
84C/184C INTERIOR 150F INTERIOR / EXTERIOR 75C/150C INTERIOR
12.5
Material 184 INTERIOR TRAC® ceiling type 75/150C distinguishes itself from the other types
because of its smooth, closed appearance. The panels about each other
Panels: 84mm/184mm wide x 12.5mm deep, with a recessed flange of Material
with a narrow V-groove. They are installed to carrier profiles and can be
12.5
23.5mm, made out of 0.50mm aluminium alloy AA 3005/3105/5052 with Panels: 150mm wide x 17mm deep, made out of 0.60mm aluminium alloy simply demounted individually, by inserting a plain strip between the
stove enamelled coil coated finish 0.45mm galvanised steel with stove 84
AA 3105/3105/5052 with stove enamelled coil coated finish / 0.50mm profiles.
39
enamelled coil coated finish. galvanised steel with stove enamelled coil coated finish.
As with all TRAC® ceilings, the 75C/150C can be applied in all types of
(Colour according to TRAC® colour chart and availability chart) À2
(Colour according to TRAC® colour chart and availability chart)
5
5
32 buildings and because of their closed appearance they are particularly
Panel lengths up to approx. 5m Panel length upto approx 5m suitable for domestic applications: living rooms, kitchens, corridors etc.
Stringers: 34.5mm wide, 48mm deep made out of 0.95mm aluminium
Panel carriers: 32mm wide, 39mm deep, made out of 0.95mm aluminium 2.5 À1 Panels: 75mm/150mm wide x 15mm deep with bevelled groove between
alloy AA5052/0.60mm galvanised steel, with prongs to hold the panels in a
25
alloy AA 5052/0.6mm galvanised steel, with cutouts to hold the panels in a panels, made out of 0.50mm thick aluminium alloy AA 3005/3105/5052 or
module of 75 /150mm.
module of 100mm (84C) or 200mm (184C), gap 16mm closed. 0.5mm thick galvanised steel.
Suspension: By means of suspension rods and spring clips.
Suspension: By means of suspension rods and spring clips. One Panel Span: 1.5m max. with insulation, 1.8m max. without insulation. (Colour according to TRAC® colour chart and availability)
suspension for every 1.5 to 2 sq.m.
Stringer Span: 1.5m max. spacing of suspension rods. Panel lengths upto approx 5 m.
Panel Span: 1.3m max. with insulation, 1.6m max. without insulation. When perforated, hole diameters are 2mm on 5mm centres (standard) or
Finish
Carrier Span: 1.3m max. spacing of suspension rods. 1mm on 2.5mm centres (micro-perforated), the holes representing 15% of
Coil Coated: Panels will be finished on exposed side with 20 microns the perforated area (150C only).
Finish polyester coil coating over primer and on the rear side with a wash coat. Panel Carriers: 32mm wide, 39mm deep made out of 0.95mm aluminium
Coil Coated: Panels will be finished on exposed side with 20 microns of 0.6mm galvanised steel, with prongs to hold panel in a module of 15mm.
polyester coil coating over primer and on the rear side with a wash coat. Suspension: By means of G.I. rod hangers and suspension clips.
Panel Span: 1.3m max. with insulation, 1.5m max. without insulation.
84C EXTERIOR
Carrier Span: 1.3m max. spacing of suspension rods.
Material
Finish
84C ceilings can also be used for exterior applications when suspended by
Coil Coated: Panels will be finished on exposed side with 20 microns
rigid suspension rods or mounted on a steel substructure. 84C exterior
polyster coil coating over primer and on the rear with a wash coat.
ceiling is available in 0.50mm aluminium alloy AA 3005/3105/5052 with
stove enamelled coil coated finish.
®
(Colour according to TRAC colour chart and availability chart)
Absorption Coefficients
Panel Span: 800mm max.
EXTERIOR 1.00
Absorption Coefficient,
Carrier Span: 500mm max. spacing of suspension angles.
Material 0.80
Finish
Panels: 150mm wide x 17mm deep, made out of 0.60mm aluminium alloy 0.60
Coil Coated: Panels will be finished on exposed side with coil coated stove AA 3105 / 5050 with stove enamelled coil coated finish / 0.50mm galvanised
0.40
enamelled PVF2 or polyurethane paint with a wash coat on the rear side. steel with stove enamelled coil coated finish.
0.20
150 C perf./25mm Mineral Wool / 0.30 0.74 0.88 0.58 0.71 0.70 0.73
200 mm air space
Frequency, Hz 125 250 500 1k 2k 4k NRC Stringers: 34.5mm wide, 48mm deep made out of 0.95mm aluminium
Frequency,Hz
84Cperf/25mm Mineral 84C Ceiling System alloy AA 5052/0.60mm galvanised steel, with prongs to hold the panels in
Wool/200mm air space 0.38 0.90 1.08 10.2 1.10 0.79 1.03 module of 150mm.
Absorption Coefficients Suspension: By means of rigid suspension angles or mounted on a steel Sound Absorption Data
sub-structure.
1.20 Frequency, Hz 125 250 500 1k 2k 4k NRC
Panel Span: 1000mm max.
1.00
150C perf/25mm Mineral
Stringer Span: 500mm max. spacing of suspension angles. Wool/200mm air space 0.30 0.74 0.88 0.58 0.71 0.70 0.73
Absorption Coefficient,
0.80
Finish
45
12.5
0.60 Coil Coated: Panels will be finished on exposed side with coil coated stove
84 16 32 enamelled PVF2/ polyurethane/SMP paint with a wash coat on rear side.
15
0.40
39
0.20 150/75
32 SUSPENSION ANGLE
PANEL CARRIER AT 500mm C/C
48
0.00 SUSPENSION CLIP
125 250 500 1000 2000 4000 NRC
17
84C perf/25mm Mineral Wool/200mm 0.38 0.90 1.08 1.02 1.10 0.79 1.03 150/200
air space
7 8
NNOVATE NITIATE NTEGRATE
Tiles and plank ceilings are available with clip-in, lay-in and C grid C-Grid Suspension System
Tile & Plank Design Ceilings suspension systems. The C-grid suspension system consists of exposed C-shaped runners which
Clip-In System are installed parallel to each other or in a square grid to form continuous
The clip-in system consists of 0.5mm galvanised steel clip in profile which is main courses. The planks are hooked onto these grids.
TRAC® tile and plank design ceiling system has been developed to meet courses. Spacing between runners corresponds to the exposed length of
both practical and aesthetical requirements of modern ceilings. The major the plank. When a square grid is required, this is made by incorporating used as the primary suspension and if required, as a secondary suspension. This system features:
advantages of the TRAC® tile/plank system are innovative suspension shorter C-shaped cross members that are butt-jointed against the main This system features: • the advantage of the possibility to fix partition walls to the strong C-Grid
systems, optional rigid grid system for suspension of exterior ceilings, choice • a rigid grid system to ensure a level ceiling and
runner and tied with a special cross piece bracket. This system is only • an exposed wide suspension system which accentuates the grid pattern
of tile material, extensive range of colours and finishes and a choice of • a hidden suspension system for an uncluttered, monolithic ceiling
suitable for interior use. The C runners are suspended from the roof slab and allows easy access to the plenum
perforations and flexibility in design specially with the plank ceiling system. appearance
The tile/plank ceiling systems are offered in stove enamelled coil coated with special suspension shoes and GI suspension angles at a maximum
steel and aluminium and powder coated steel and aluminium finishes and distance of 1200mm centre to centre. Alternative Lay-Out
offer the advantage of easy cleaning, non-static properties and inert material.
Edge Cover Profile
Incandescent and halogen type spot lights can be easily incorporated in the
Tiles/planks are trimmed along the wall perimeter by means of 19x19mm
tile ceilings and fluorescent fittings within the plank ceilings. HOOK AND BUTTERFLY CLIP
roll formed steel or aluminium edge cover profile.
Tiles CROSS TEE
Paint Finish
Tiles are manufactured out of coil coated galvanised steel/aluminium alloy TRAC LAY- IN TILE TRAC LAY- IN TILE / PLANK
Steel tiles/planks: Steel tiles/planks are finished on exposed side with 20 EDGE COVER PROFILE
(TEGULAR) (SQUARE EDGE)
AA 3105/3005/5202 on advanced equipment, which includes several
micron polyester coil coating over primer in approved shade and backing WALL
levelling stages in the manufacturing process. For the clip-in tile, two sides of Lay-In System
coat on rear surface (nominal 5 microns), or with a 50 micron epoxy
each tile are raised and pipped and stopped to ensure positive engagement
polyester powder coating on exposed surface. Straight Joints
into the spring tee yet allow demounting of individual tiles.
Aluminium tiles/planks: Aluminium tiles/planks are finished on exposed
For the lay-in system, the tiles have a flange on each end which lays on the METAL FASTENER
side with 20 micron polyester coil coating over primer in approved shade R.C.C. SLAB
exposed grid. All tiles have square/bevelled edges.
and backing coat on rear surface (nominal 5 microns), or with a 50 micron
CEILING BRACKET
Planks epoxy polyester powder coating on exposed surface. Wall angles are
SUSPENSION ANGLE
Planks are manufactured out of coil coated aluminium alloy finished with 50 micron epoxy polyester powder coating paint in broken
AA 3105/3005/5202 galvanised steel produced on advanced equipment white shade. SUSPENSION SHOE
Clip-in planks: The short sides of each plank are raised and pipped and TRAC® tiles and planks are also available with perforations for providing C-GRID C-GRID 0.7
WALL
stopped to ensure positive engagement into the spring tee, yet allow acoustic performance characteristics. TRAC tiles and planks are perforated ®
C Grid Suspensions System
demounting of the individual planks as a standard with 2.5mm dia. holes at 5.5mm centre to centre in a regular
Lay-in and C-Grid planks: These planks have a flange on each end, which pattern. Other special/non-standard perforations are also available. Tiles
lay on the exposed grid or C-grid. The planks can be laid and easily removed and planks when backed with 25mm thick resin bonded mineral wool Combined Tile Sizes
CEILING BRACKET
without the aid of special tools. Planks over 1500mm in length have an (48 kg/m2) provide good sound absorption. Tiles and planks are also AT 1200mm C/C G.I. SUSPENSION ANGLE
AT 1200 mm C/C
additional stiffening flange on the long side. available with a factory applied acoustic tissue to the back side, which HOLD ON CLAMP’
AT 1200MM C/C (Max.)
clamps at max. 1200mm centre to centre along the clip in profile. This rigid 25mm Mineral Wool 0.50 1.00 1.02 1.07 1.06 1.05 1.04
Lay-In System
suspension is also suitable for exterior use. The lay-in system comprises the Trac 8011 exposed grid suspension. This
Absorption Coefficients
grid features stab-in coupling and is demountable.
Lay-in-System: Suspension system is standard 24mm table exposed metal 1.20
grid. Grid features 38mm high main runners and cross tees, roll formed
This system features :
from galvanised steel to BS 2989 Z-18 zinc coating. The main runners 1.00 • easy access to the plenum
WALL
feature bayonet ends and the cross tees stab ends for quick and simple • a rigid fire rated grid to ensure a level ceiling and an exposed grid
Absorption Coefficient,
Perf tile/acoustic tissue 0.48 0.93 0.62 0.69 0.80 0.75 0.76
600 300 0.7 0.5
X
C-grid System: The suspension system consists of exposed C shaped Perf tile/25mm Mineral Wool
f
runners which are installed parallel to each other to form continuous main 305 1264 0.7 0.6
d
e
Frequency, Hz
g
9 10
NNOVATE NITIATE NTEGRATE
distort and showed only a minimal increase in weight. Unlike most other 1200mm along the length of the tee. The tees would be in filled with
®
TRAC GRG Ceiling ceiling materials, this important attribute can often be used to speed up the
building program by installing the ceiling before the building is fully
1200mm and 600mm cross tees. The grid manufacturers
recommendations should be followed at all times.
weathertight. Note: All perimeter tiles may be supported on only 3 sides without risk of
GRG TILES
sagging. Tiles can easily be cut by using a carpenters fine tooth saw; the
TILES lines should be placed face down on a flat, clean surface for cutting.
Composition
®
Sound Absorption Data
The TRAC GRG range of ceiling tiles are manufactured from glass
Frequency, Hz 125 250 500 1k 2k 4k NRC
reinforced gypsum and comprise non-combustible gypsum casting
plaster reinforced with a glass fibre membrane resulting in a light weight, GRG T 206, no holes/25 MW 0.20 0.40 0.55 0.10 0.21 0.50 0.32
strong and prestressed panel. GRG T 206, no holes 0.09 0.10 0.10 0.12 0.25 0.35 0.14
Surface Finish
The plaster has a silky smooth or textured moulded finish. Absorption Coefficients
Colour 0.60
The tiles are normally supplied in their natural white finish and can be 0.50
pre-decorated to order.
Absorption Coefficient, a
0.40
Dimensions
0.30
All designer tiles are designed for installation on a standard 600x600mm
module 24mm table exposed metal grid and are precision made to within 0.20
upon the gypsum source. GRG T 206, no holes/25 MW 0.20 0.40 0.55 0.10 0.21 0.50 0.32
GRG T 206, no holes 0.09 0.10 0.10 0.12 0.25 0.35 0.14
2
Tile Kg/tile Kg/m Frequency, Hz
11 12
NNOVATE NITIATE NTEGRATE
Accessories List of major projects where TRAC® ceiling system has been used
13 14
NNOVATE NITIATE NTEGRATE
Regional Offices and Manufacturing Units
Interarch Building Products offer turnkey operations with regional offices and project control
NNOVATE NITIATE NTEGRATE
centres for marketing, sales and coordination at all locations across India.
Chandigarh
M/s. Interarch Building Products Pvt. Ltd. M/s. Interarch Building Products Pvt. Ltd.
Plot No: 29, Udyog Vihar, Plot No: D-1/1, SIPCOT Industrial Park, Mambakkam,
M/s. Interarch Building Products Pvt. Ltd. M/s. Interarch Building Products Pvt. Ltd.
Plot No: 14, Sector - 2, Plot No: A, Khasra No: 276-A,
Integrated Industrial Estate, Pantnagar 2 KM on Kichha - Rudrapur Road,
Ahmedabad Bhopal
Rudrapur - 263 153 (Uttarakhand) Kichha - 263 148
Indore
Kolkata Mob: 09319268211 Distt: Udham Singh Nagar (Uttarakhand)
Mob: 09760690304
Mumbai
Pune
For faster processing of enquiries from - Ahmedabad, Bangalore, Baroda, Bhopal, Chennai, Chandigarh,
Hyderabad Hyderabad, Indore, Kolkata, Kochi, Mumbai, Nagpur, Pune, please contact:
Regional Office
Manufacturing Unit
15 16
NNOVATE NITIATE NTEGRATE