Professional Documents
Culture Documents
Report PDF
Report PDF
1
Company: Page: 1
Specifier: Project:
Address: Sub-Project I Pos. No.:
Phone I Fax: | Date: 09/07/2018
E-Mail:
Specifier's comments:
1 Input data
Anchor type and diameter: HIT-HY 200 + HIT-Z 1/2
Effective embedment depth: hef,opti = 70 mm (hef,limit = 93 mm)
Material: DIN EN ISO 4042
Evaluation Service Report: ESR-3187
Issued I Valid: -|-
Proof: Design method CSA A23.3-14 / Chem.
Stand-off installation: eb = 0 mm (no stand-off); t = 20 mm
Anchor plate: lx x ly x t = 508 mm x 458 mm x 20 mm; (Recommended plate thickness: not calculated
Profile: Square HSS (AISC); (L x W x T) = 305 mm x 305 mm x 6 mm
Base material: cracked concrete, fc' = 17.24 N/mm2; h = 150 mm, Temp. short/long: 20/20 °C
Installation: hammer drilled hole, Installation condition: Dry
Reinforcement: tension: condition B, shear: condition B; no supplemental splitting reinforcement present
edge reinforcement: none or < 15M bar
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.ca Profis Anchor 2.7.1
Company: Page: 2
Specifier: Project:
Address: Sub-Project I Pos. No.:
Phone I Fax: | Date: 09/07/2018
E-Mail:
3 Tension load
Load Nf [kN] Capacity Nr [kN] Utilization bN = Nf/Nr Status
Steel Strength* 0.999 35.405 3 OK
Pullout Strength* 0.999 31.620 4 OK
Sustained Tension Load Bond Strength* N/A N/A N/A N/A
Concrete Breakout Strength** 2.423 18.200 14 OK
* anchor having the highest loading **anchor group (anchors in tension)
Variables
n Ase,N [mm2] futa [N/mm2]
1 92 649.48
Calculations
Ns,uta [kN]
59.504
Results
Ns,uta [kN] fs R Nsar [kN] Nfa [kN]
59.504 0.850 0.700 35.405 0.999
Variables
y c,p la Ncpr,A [kN]
1.000 1.000 48.646
Calculations
-
-
Results
y c,p l a Ncpr,A [kN] fc R Ncpr [kN] Nfa [kN]
48.646 0.650 1.000 31.620 0.999
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.ca Profis Anchor 2.7.1
Company: Page: 3
Specifier: Project:
Address: Sub-Project I Pos. No.:
Phone I Fax: | Date: 09/07/2018
E-Mail:
Ncbgr = (AA ) y
Nc
Nc0
ec,N y ed,N y c,N y cp,N Nbr CSA A23.3-14 Eq. D.4
Ncbgr ≥ Nfa,g CSA A23.3-14 Table D.1
ANc see CSA A23.3-14, Part D.6.2.1, Fig. D.7
ANc0 = 9 h2ef CSA A23.3-14 Eq. D.5
( )
1
y ec,N = 2 e'N ≤ 1.0 CSA A23.3-14 Eq. D.8
1+
3 hef
y ed,N = 0.7 + 0.3 ( ca,min
1.5hef )
≤ 1.0 CSA A23.3-14 Eq. D.11
y cp,N = MAX (
ca,min 1.5hef
cac
,
cac )
≤ 1.0 CSA A23.3-14 Eq. D.13
1.5
Nbr = kc f c l a √fc hef R
'
CSA A23.3-14 Eq. D.6
Variables
hef [mm] e'1,N [mm] e'2,N [mm] ca,min [mm] y c,N
70 88 38 ∞ 1.000
Calculations
ANc [mm2] ANc0 [mm2] y ec1,N y ec2,N y ed,N y cp,N
182120 43911 0.542 0.734 1.000 1.000
Results
fc R Nbr [kN] Ncbgr [kN] Nfa,g [kN]
0.650 1.000 11.028 18.200 2.423
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.ca Profis Anchor 2.7.1
Company: Page: 4
Specifier: Project:
Address: Sub-Project I Pos. No.:
Phone I Fax: | Date: 09/07/2018
E-Mail:
4 Shear load
Load Vf [kN] Capacity Vr [kN] Utilization bV = Vf/Vr Status
Steel Strength* 1.675 14.466 12 OK
Steel failure (with lever arm)* N/A N/A N/A N/A
Pryout Strength (Concrete Breakout 10.050 107.263 10 OK
Strength controls)**
Concrete edge failure in direction ** N/A N/A N/A N/A
* anchor having the highest loading **anchor group (relevant anchors)
Variables
n Ase,V [mm2] futa [N/mm2]
1 92 649.48
Calculations
Vs,uta [kN]
26.182
Results
Vs,uta [kN] fs R Vsar [kN] Vfa [kN]
26.182 0.850 0.650 14.466 1.675
( )
1
y ec,N = 2 e'N ≤ 1.0 CSA A23.3-14 Eq. D.8
1+
3 hef
y ed,N = 0.7 + 0.3 ( ca,min
1.5hef )
≤ 1.0 CSA A23.3-14 Eq. D.11
y cp,N = MAX (
ca,min 1.5hef
cac
,
cac )
≤ 1.0 CSA A23.3-14 Eq. D.13
1.5
Nbr = kc f c l a √fc hef R
'
CSA A23.3-14 Eq. D.6
Variables
kcp hef [mm] e'1,N [mm] e'2,N [mm] ca,min [mm]
2 70 0 0 ∞
Calculations
ANc [mm2] ANc0 [mm2] y ec1,N y ec2,N y ed,N y cp,N
213552 43911 1.000 1.000 1.000 1.000
Results
fc Nbr [kN] Vcpg [kN] R Vcpgr [kN] Vfa,g [kN]
0.650 11.028 107.263 1.000 107.263 10.050
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.ca Profis Anchor 2.7.1
Company: Page: 5
Specifier: Project:
Address: Sub-Project I Pos. No.:
Phone I Fax: | Date: 09/07/2018
E-Mail:
6 Warnings
• Load re-distributions on the anchors due to elastic deformations of the anchor plate are not considered. The anchor plate is assumed to be
sufficiently stiff, in order not to be deformed when subjected to the loading!
Input data and results must be checked for agreement with the
existing conditions and for plausibility!
• Condition A applies when supplementary reinforcement is used. The R factor is increased for non-steel Design Strengths except Pullout
Strength and Pryout strength. Condition B applies when supplementary reinforcement is not used and for Pullout Strength and Pryout
Strength. Refer to your local standard.
• Checking the transfer of loads into the base material is required in accordance with CSA A23.3!
• Installation of Hilti adhesive anchor systems shall be performed by personnel trained to install Hilti adhesive anchors. CSA A23.3-14 Annex
D, Clause D.10.1
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.ca Profis Anchor 2.7.1
Company: Page: 6
Specifier: Project:
Address: Sub-Project I Pos. No.:
Phone I Fax: | Date: 09/07/2018
E-Mail:
7 Installation data
Anchor plate, steel: - Anchor type and diameter: HIT-HY 200 + HIT-Z 1/2
Profile: Square HSS (AISC); 305 x 305 x 6 mm Installation torque: 0.040 kNm
Hole diameter in the fixture: df = 14 mm Hole diameter in the base material: 14 mm
Plate thickness (input): 20 mm Hole depth in the base material: 95 mm
Recommended plate thickness: not calculated Minimum thickness of the base material: 127 mm
Drilling method: Hammer drilled
Cleaning: No cleaning of the drilled hole is required
254 254
79
1 2
229
150
3 4 x
150
229
5 6
79
42 425 42
Coordinates Anchor mm
Anchor x y c-x c+x c-y c+y Anchor x y c-x c+x c-y c+y
1 -213 150 - - - - 4 213 0 - - - -
2 213 150 - - - - 5 -213 -150 - - - -
3 -213 0 - - - - 6 213 -150 - - - -
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.ca Profis Anchor 2.7.1
Company: Page: 7
Specifier: Project:
Address: Sub-Project I Pos. No.:
Phone I Fax: | Date: 09/07/2018
E-Mail:
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan