Professional Documents
Culture Documents
YELLOW : SYSTEM IS ON
INDICATOR LIGHTS
Main Breaker:
220v 100A
1SF – 1 NORMAL PRESSURE: 14-15 psi
OGF
NORMAL PRESSURE: 28 psi
PRESSURE GAGES
Critical Pressure: 80 psi
START UP OPERATION:
1. Turn ON main breaker located beside the wall.
-Main CB, RWP1, RWP2, FFP, HPP, System CB, DP 1&2, DP 3&4
NOTE: DO NOT turn ON breaker of EP and BW. EP is spare ONLY while BW is for BACKWASH OPERATION
ONLY.
OPERATION: AUTO
1. Select selector switch of “SYS SW” (System Switch) to A (Auto).
OPERATION: MANUAL
Manual operations is to test all pumps manually if all are functioning well.
3. Turn selector switch of RWP 2 SW (Raw Water Pump 2 Switch) and DP 1-2 SW (Dosing Pump 1-2
Switch) to M (Manual). This two selector switches are partners. So we should turn on both selector
switches.
4. Turn selector switch of FFP SW (Filter Feed Switch), DP 3-4 SW (Dosing Pump 3-4), and HPP SW
(High Pressure Pump) to M (Manual).
- Main CB, RWP1, RWP2, FFP, HPP, System CB, DP 1&2, DP 3&4
-- Main CB, RWP1, RWP2, FFP, HPP, System CB, DP 1&2, DP 3&4
5. DRAIN the existing water on the tanks of RWT (Raw Water Tank) and MT (Mixing Tank) by
turning the 3 pcs of gate valves counter clockwise. This is to secure the smell of the area during
long vacations.
Manual operations is to test all pumps manually if all are functioning well
1. Turn selector switch to “O” (OFF) of FFP SW (Filter Feed Switch), DP 3-4 SW (Dosing Pump 3-4), and
HPP SW (High Pressure Pump).
2. Turn selector switch to “O” (OFF) of RWP 2 SW (Raw Water Pump 2 Switch) and DP 1-2 SW (Dosing
Pump 1-2 Switch).
3. Turn selector switch to “O” (OFF) of RWP 1 SW (Raw Water Pump 1 Switch) to M (Manual)
TIMERS:
During automatic operations:
TIMER 1: Auto- after 10 seconds the RWP 1 and RWP 2 will operates.
TIMER 2: After RWP 1 and RWP 2 operates, it takes also 10 seconds to automatically pumps the FFPand
HHP.
TIMER 3: If any tank is in LOW LEVEL, it will buzz for a few seconds and RED indicator will light.
If the tanks reaches its normal level, the RED light will stop and it will back again to operate.
OPERATION: BACKWASH
Check gate valves of either 1SF or 2SF if it is open or close.
4. Check gate valves and DON’T FORGET to return it to its orientation for normal operation.
GREEN LIGHTS: RED LIGHTS:
SELECTOR SWITCHES:
A= Auto M= Manual
O= OFF T= Test
QMTOLP1
SYS SW = System switch. QMTOLP2
RWP 1 SW = Raw Water Pump 1 switch
RWP 2 SW = Raw Water Pump 2 switch
QMTOLP3 THERMAL OVERLOADS
DP 1-2 SW = Dosing Pump 1-2 switch QMTOLP4
FFP SW = Filter Feed Pump switch QMTOLP5
DP 3-4 SW = Dosing Pump 3-4 switch QMTOLP6
HPP SW = High Pressure Pump switch
EP SW = SPARE
BWP SW = Backwash Pump switch