Professional Documents
Culture Documents
STAAD - Pro & STAAD Advanced Concrete Designer RCDC: Design of Two-Storey Reinforced-Concrete Residential Structure Using
STAAD - Pro & STAAD Advanced Concrete Designer RCDC: Design of Two-Storey Reinforced-Concrete Residential Structure Using
Main objectives
1) Calculate Wind Pressure for Components and Cladding per NSCP 20
2) Design the Roof Truss and Purlins per NSCP 2015/AISC 360-10 by LR
3) Derive dead load and live load values per NSCP 2015
4) Discuss NSCP 2015/UBC 97 Seismic parameters input to STAAD
5) Design the concrete elements in STAAD Advanced Concrete Designe
(beams, slabs, columns and footings)
SIDENTIAL STRUCTURE USING
Concrete Designer RCDC
STORIES (LEVELS)
Footing to GF 1.8
GF to 2F 3
2F - Roof Beam 3
Roof Beam - Apex 2
9.8
Roof mean Height for wind load calculation
7.00 m
Roof Slope = 22.62deg
40km
STORIES (LEVELS)
Levels Storey Height (m)
Footing to GF 14
GF to 2F 3
2F - Roof Beam 3
Roof Beam - Apex 2
22
PROPERTIES
Beams Columns Slabs fc' fy
RB250x400 RC450X350 S115 20.68 Mpa 275 Mpa
(3000psi) (Gr40)
LOADS
Dead Load
1) Selfweight
Concrete unit weight = 24 kN/m3
2) Member Load
150mm CHB 3.11 kN/m per meter height
100mm CHB 2.98 kN/m per meter height
Live Load
1.9 kN/m2 0.60 kN/m2
Seismic Parameters
UBC 97 / NSCP 2015
Zone = 4
Seismic Source Type = A
Importance Factor ( I ) = 1.0 (Standard Occupancy)
R = 8.5 - Special Moment Frame
Structure is located 40km from seismic source
Ct = 0.0731
Wind Parameters
Wind (ASCE 7-10 / NSCP 2015)
Vwind = 250 kph
I = 1.0
Exposure = B (typical residential structure in urban area)
=
Low‐Rise Buildings : Component and Cladding
Simplified Procedure
ASCE 7-10
PURLINS (EFFECTIVE ARE
Zone
1
2.14
-3.62
PURLIN SPACING =
1.07
-1.81
Pnet = λ Kzt Pnet9
6.68
-13.52
PURLINS (EFFECTIVE AREA = 2.25 m2)
350kph
Zone
2 3 MEAN HEIGHT 7m
2.14 0 kn/m2 WIDTH 8m
-5.96 0 kn/m2 LENGTH 12
PURLIN SPACING = 0.5 a .8m
0.75
PARAMETERS T = Ct (hn) sec UBC Eq. (30-8)
Z 0.4 = 0.341 sec
I 1 < 0.70 sec therefore Ft = 0;
Rwx 8.5
Rwz 8.5
Na 1
Nv 1 V= CvIW KN UBC Eq. (30-4)
S 4 RT
Ct 0.0731 = 386.90 KN
hn 7.8
W 1753.2
Cv 0.64
Ca 0.44
If Ft≠ 0:
Ft = 0.07TV UBC Eq. (30-14)
= 9.24 KN
< 0.25V = 96.73
1 1.400 D
1 1.200 D + 1.600 Lp
1 1.420 D + 0.500 Lp + 1.250 E1
1 1.420 D + 0.500 Lp + 1.250 E2
1 1.420 D + 0.500 Lp - 1.250 E1
1 1.420 D + 0.500 Lp - 1.250 E2
1 1.420 D + 1.250 E1
1 1.420 D + 1.250 E2
1 1.420 D - 1.250 E1
1 1.420 D - 1.250 E2
1 0.680 D + 1.250 E1
1 0.680 D + 1.250 E2
1 0.680 D - 1.250 E1
1 0.680 D - 1.250 E2
E = ρ Eh + Ev
1.25
= 1.25 Eh
Ev = 0.5 Ca I DL
0.5 0.44 1 DL
= DL
= 0.22 DL