Professional Documents
Culture Documents
Note: Encircle the letter of only one answer which you think is most appropriate.
a. 1100 mm
b. 1105 mm
c. 1095 mm
d. 1110 mm
4. In thickness formula for internal pressure for shell, term ‘E’ refers
to:
--------------------------------------------------------------------------------------------------------------------------------------------------------------
/conversion/tmp/scratch/481697101.doc
6/27/2020 / 8:03:11 AM / NCD
Professional Training and Consultation
API 510 Preparatory
20 – 31 August 2005, Al-Khobar
Page 2 of 7
a. 10 psi
b. 43.3 psi
c. 4.33 psi
d. None of the above
a. API 510 ,
b. ASME Sec. 1,
c. ASME Sec. VIII Div. 1,
d. None of these
a. API 510
b. API 570
c. ASME Section VIII Div.1
d. None of above
a. Longitudinal joints
b. Circumferential joints, shell to shell
c. Shell to hemispherical head joint
d. a and c above
a. Torispherical
b. Hemispherical
c. Ellipsoidal
d. All will be same
--------------------------------------------------------------------------------------------------------------------------------------------------------------
/conversion/tmp/scratch/481697101.doc
6/27/2020 / 8:03:11 AM / NCD
Professional Training and Consultation
API 510 Preparatory
20 – 31 August 2005, Al-Khobar
Page 3 of 7
a. 3 to 1 min
b. 4 to 1 min
c. 3 to 2 min
d. 1 to 2 min
11. ASME Sec VIII Div. 1 specifies different acceptance level for weld
reinforcement, which of the following statements are true in your
opinion?
--------------------------------------------------------------------------------------------------------------------------------------------------------------
/conversion/tmp/scratch/481697101.doc
6/27/2020 / 8:03:11 AM / NCD
Professional Training and Consultation
API 510 Preparatory
20 – 31 August 2005, Al-Khobar
Page 1 of 7
14. A Pressure Vessel is designed for 0.85 joint efficiency with full
penetration welds. RT requirement will be:
a. Nil
b. Spot
c. 100 %
d. T-joints radiography
a. 25 inch, 4 inch
b. 50 inch, 3 inch
c. 50 inch, 3¾ inch
d. 25 inch, 2 inch
16. If there is a conflict between ASME VIII & API 510 Code, for
vessels in-service:
17. Two head to shell joints, one joining a seamless Hemisph, head
to shell was radiographed for full length and the other joint
joining seamless std. torisph. head to shell was spot
radiographed, The weld joint efficiency for each of these heads
respectively will be:
a. 1, 0.85
b. 1, 1
c. 0.85, 1
d. 0.85, 0.85
--------------------------------------------------------------------------------------------------------------------------------------------------------------
/conversion/tmp/scratch/481697101.doc
6/27/2020 / 8:03:11 AM / NCD
Professional Training and Consultation
API 510 Preparatory
20 – 31 August 2005, Al-Khobar
Page 2 of 7
19. Vessel MAWP for tall vertical vessel will normally be:
a. RT3 means E = 1
b. RT2 means E = 0.85
c. RT1 and RT2 may mean E = 1
d. RT4 means spot radiography
---------------------End-----------------------
Q. ANSWER REFERENCE
--------------------------------------------------------------------------------------------------------------------------------------------------------------
/conversion/tmp/scratch/481697101.doc
6/27/2020 / 8:03:11 AM / NCD
Professional Training and Consultation
API 510 Preparatory
20 – 31 August 2005, Al-Khobar
Page 3 of 7
--------------------------------------------------------------------------------------------------------------------------------------------------------------
/conversion/tmp/scratch/481697101.doc
6/27/2020 / 8:03:11 AM / NCD