Professional Documents
Culture Documents
5703 Updating Guide_WP
Version:1.0
Date: 15/07/2014
By: Guofang
Content
1. Preparation‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐3
a. Download cable‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐4
b. Driver, Tool and Code‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐5
2. Note‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐6
3. Procedure‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐7
4. Step‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐8
a. Driver installation‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐8
b. Update‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐‐13
Preparation
1. Download cable
Part name: 5pin USB cable
2. Driver, Tool and Code
Version Address Note
FTP://124.127.119.45
Driver simpleio driver
TOOLS/Qualcomm/
FTP://124.127.119.45
Tool MicrosftFFutool update tool
TOOLS/Qualcomm/
FTP://124.127.119.45
Code 5703XX_XXXX_VXXXX software code
SOFTWARE/5703/
Note
1. Do not insert SIM card when you update software.
2. Check software version in “setting>about phone>phone information” before updating,
make sure it matches the version you want to update.
3. This update tool can only works with Win7 or Win 8 system, and should use administrator
mode to update.
4. Check software version is normal or not after updating.
Step
1. Install the driver.
(1) Power off handset, press power key, after the phone vibrates, then press voice up key, the
phone will enter download mode, interface as below:
(2) Connect USB cable and click to install the driver. After install the
driver successfully, you can find “WP8 UEFI UBS Simple I/O” port in device manager. As below:
2. Update.
(1) With Win7 or Win8 32 bit system, Open in
“MicrosftFFutool\32\ImageDesigner” file, with Win7 or Win8 64 bit system, open
in “MicrosftFFutool\64\ImageDesigner” file, then select “Flash a
Windows Phone image onto your phone”, then click “Next”
(2) Click “Change” and select “.FFU” file in software code.
(3) Click “Flash” to start upgrade.
(4) Complete upgrade.