Professional Documents
Culture Documents
item_id=951
Home About Boysen News Facilities Products Colors MSDS Locate A Dealer Contact Us
Products
Featured Products
Premium Water Based Paints
Coatings
Boysen® Epoxy Primer
Oil Wood Stains
Coatings
Hi-Performance Elastomeric
Features:
Paint
Based Coatings PRINCIPAL USES: As a primer for topcoats of Epoxy Enamel or Acqua Epoxy™ to be applied on
metal, galvanized iron, wood and masonry
Surface Preparation Chemicals
PRACTICAL COVERAGE: 20-25 square meter / 4 liters / coat
Premium Economy
Elastomeric Paint
SURFACE DRY: 2-3 hours
PACKAGING: Boysen® Epoxy Primer comes in 4-liter cans, ¾ full packed with Curing Agent in a
1-liter can
AVAILABLE COLORS:
B-2200 White with curing agent #2202
B-2230 Gray with curing agent #2202
B-2277 Red Oxide with curing agent #2202
Instructions
1 of 2 5/27/2012 9:27 AM
Boysen® Epoxy Primer http://www.boysen.com.ph/products.do?item_id=951
SURFACE PREPARATION:
Concrete Flooring:
Remove oil and grease by detergent cleaning. For very smooth floors, acid etch smooth surfaces to
improve adhesion. Do this by mixing one (1) part muriatic acid to one (1) part water. Apply over
masonry and let stand for 2-3 minutes. Rinse with water. If available, rinse by pressure washing.
Finished acid etched texture should be similar to that of 40-60 grit sandpaper. Make sure that the
surfaces to be painted are clean and dry.
Caution: Adequate protection and ventilation should be provided when working with acids.
Metal:
Wipe the surface with rag soaked in paint thinner to remove dust, dirt, grease, oil, wax and other
foreign matter. For new G.I. sheets, etch the surface by applying 10% Boysen® Metal Etching
Solution #71 (dilute 1 part of B-71 to 9 parts water).
If repainting on surfaces with alkyd or lacquer based coatings, scrape off all paint. Remove oil and
grease by detergent cleaning followed by scuff sanding. To remove rust, wire brush or scrape
affected areas and apply Boysen® Metal Etching Solution #71. Let it stay for 10-15 minutes. Be sure
to wash off surface thoroughly with water, letting it dry before applying paint. Primer should be applied
immediately after treatment.
PAINTING SCHEDULE:
Concrete Flooring:
Mix three (3) parts of Boysen® Epoxy Primer White #2200 to one (1) part of its catalyst.
Allow twenty (20) minutes induction time. Dilute 1:1 ratio with Boysen® Epoxy Reducer #55. Apply as
primer coating on bare concrete. Let dry overnight. Topcoat with 2-3 coats of Boysen® Acqua
Epoxy™ or Boysen® Epoxy Enamel. Let dry overnight before recoating. Let cure for 3 days before
allowing foot traffic and 7 days for heavy duty use.
Metal:
Prime bare metal Boysen® Epoxy Red Oxide #2277 or Boysen® Epoxy Primer Gray #2230. Let dry
eight (8) hours before recoating. Topcoat with 2-3 coats of Boysen® Acqua Epoxy™ or Boysen®
Epoxy Enamel. Let dry overnight before recoating.
NOTE: For epoxy-primed surfaces, topcoat should be applied not more than seven (7) days after
priming to ensure good intercoat adhesion. Otherwise, re-priming is needed.
Choose Color
For technical reasons connected with color reproduction and paint manufacturing, these
patterns may not exactly match the paint color.
Home | About Boysen | News | Facilities | Products | Colors | MSDS | Newsletter | Locate A Dealer | Contact Us
© 2012 Boysen Paints. All Rights Reserved.
2 of 2 5/27/2012 9:27 AM