Heat Shrink MV Terminations
Heat Shrinkable Termination System for Cables
Cy Ret) alg
Universal Selection Procedure
Simplified selection table
allows quick selection based
fon conductor cross. section
and voltage class for either
polymeric or MIND paper
Insulated cables (For MI draining
cll cables, contact your local
representative)
Simple modification codes
permit easy specification of
‘optional accessory kits
Enhanced range-taking ability
means that one kit fits more
conductor sizes, reducing
stocking requirements
+ Unlimited shelf life allows
stocking of economic quantities
without product spoilage
‘Simplified Cable Preparation
Improved treatment of screen
ccut back is compatible with all
state of the art screen removal
techniques
No tap
required
No. polishing of polymeric
insulation surface
+ No special preparation
of sectored, or eccentric
conductors, or of cable that is
curved after unreeling from the
cable drum
+ Cable preparation steps are
simiiar to those for Raychem
Joints
ing of insulation
‘Simplified Installation
Components are lightweight,
‘and non-shattering
CClear instruction sheets
Common installation procedure
for polymeric and MIND paper
cables
Factory engineered kit permits
rapid on-site installation
te.com/energy
+ No mechanical stress at
insulation screen cutback
+ Termination accommodates
same bending radius as cable
+ Visual confirmation of correct
assembly sequence possible
after installation
+ Rain skirts can be installed to
allow either top or bottom feed
+ No. soldering of earthing
accessories required
Outstanding Long-Term Reliability
+ Fully sealed against water
ingress from the environment
for from within the conductor
strands
+ Polymeric materials load
eycle with the cable without
mechanically stressing
termination components and
sealants
+ Unsurpassed performance in
polluted environments, proven
over three decades
EPKT/HVT
=TE
Page 73Heat Shrink MV Terminations
Terminations System Designer
‘This worksheet enables you to arrive at a part number for an EPKT termination,
Choose one figure from the left-hand colurnn of each table,
‘Typical part number:
EPKT- 17C3MOH3
Voltage (Umax) ———___
Cable size
Number of cores
Dielectric
Location
Length (S-core-cables)
[jy fora kv A175 kV
Dielectric of insulation type:
[eo | erovrcor
Length (only 3 Core) | of the terminated portion (all)
[pe —___|______teresonm in noose and vinesoy |
Ha for 1200 lone
te.com/energy Page 74Heat Shrink MV Terminations
TIkV MIND Paper Seroened/Bolted Cables Single Core without Armour
Catalogue Reference (ross Section
‘una come)
STANDARD TAIL LENGTHS:
Sold at sat of three
co
TIkV MIND Paper Screened/Belted Cables 3/Core with or without armour
Catalogue Reference ‘cross Section
outdoor one
STANDARO TAIL LENGTHS: Con
s/oore
22kV MIND Paper Screened/Belted Cables Single Core without Armour
Catalogue Reference ‘cross Section
outdoor one
STANDARD TAIL LENGTHS: i/o
Sold at sat of three
22kV MIND Paper Screened/Belted Cables 3/Core with
C018 indo
or without armour
Catalogue Reference ‘cross Section
outdoor one
STANDARD TAIL LENGTHS: i/Core indoor = 140mm, Outs
te.com/energy
C018 not
Page 75Heat Shrink MV Terminations
les Single Core without Armour
Catalogue Reference: ‘cross Section
Outdoor tom)
STANDARD TAIL LENGTHS: Core indoor» 700mm Outsoor» 850m
2/Core indoor = 750mm Outdoor
tof hee
‘33KV MIND Paper Screened Cables 3/Core with or without armour
Catalogue Reference Catalogue Reference, Cross Section
Indoor Outdoor comm)
Ener ease aad 3570
PRT 6644-77 PRT 6520-07 95.50
EPKT 6650-97 [Epa 6926.97 185-300
ERT 66560 EPKT 6532-PT 400
STANDARD TAIL LENGTHS: Core indoor» 700mm Outsoor» 850m
5 [Care indoor = 750mm Outdoor = 800mm
tecom/eneray pace «TEHeat Shrink MV Terminations
Terminations System Designer
‘This worksheet enables you to arrive at a part number for an HVT termination.
Choose one figure from the left-hand colurnn of each table,
‘Typical part number:
HVTi- 7C3MH3
Location
Veltage (Umax)
cable size
Number of cores oo
Dielectric
Lenath (3-core-cables)
Location ‘of the termination
Voltage in kV
orld kV 4175 kV
LLenath (only 3 Core) | of the terminated portion (aD)
[a {or 650mm ong (rin for VAY outdoor and 6K ndoo
ry for 1200 ln
te.com/energy Page 77