Professional Documents
Culture Documents
Floors in Scope 1
Project Defaults
Ceiling Type Drop Ceiling
Factory startup is not required. If you want a Lutron technician to program/commission your system, please contact your local rep Where To Buy or Lutron.
Selected Solution
Description Vive PowPaks are installed on junction boxes above the ceiling and low voltage 0-10V control wires are routed to each fixture. Pico wireless
keypads are used for local control and can be easily mounted over existing wallboxes, or where no wallbox exists. Fixtures sharing the same 0-10V
wiring will be controlled together as a zone.
This tool is intended to be used for budgetary project estimates and does not replace detailed submittal and design documentation. It assumes a square footprint for each
floor of the building with adjacent spaces to fully utilize the wireless coverage of each Vive hub. The system must be designed and installed in accordance with Lutron
device and system specifications. Please consult with a Lutron sales representative to discuss the details of your project and refer to the Vive Design Guide to learn more
about designing a Vive system.
Ceiling Height 10 ft 0 in
Classroom (8)
Ceiling Height 10 ft 0 in
Ceiling Height 10 ft 0 in
Corridor (2)
Ceiling Height 10 ft 0 in
Restroom (3)
Ceiling Height 10 ft 0 in
Ceiling Height 10 ft 0 in
Atrium (1)
Ceiling Height 12 ft 0 in
Stairwell (4)
Ceiling Height 10 ft 0 in
SharedEquipment (2)
Disclaimer
THIS INFORMATION HAS BEEN GENERATED BY A SOFTWARE PROGRAM THAT IS INTENDED TO BE USED FOR BUDGETARY PROJECT ESTIMATES AND DOES NOT
REPLACE DETAILED SUBMITTAL AND DESIGN DOCUMENTATION, AND EXCLUSIVELY FOR PROJECTS IN THE UNITED STATES & CANADA ONLY; FINAL LABOR NUMBERS
MAY VARY DEPENDING ON INSTALLATION CONDITIONS AND SPECIFIC PROJECT SITE REQUIREMENTS.
THIS INFORMATION AND ALL OTHER INFORMATION WITHIN AND GENERATED BY THE SOFTWARE PROGRAM INCLUDING, BUT NOT LIMITED TO, ALL PROPOSALS,
ESTIMATES, AND SOLUTIONS (COLLECTIVELY, THE “INFORMATION”) HAS BEEN GENERATED BASED ON CERTAIN ASSUMPTIONS AND DEFAULT FIGURES AND ON DATA
ENTERED BY YOU OR A THIRD PARTY OTHER THAN LUTRON. THE ASSUMPTIONS AND DEFAULT FIGURES MAY NOT BE APPLICABLE TO YOUR PARTICULAR PROJECT.
LUTRON IS NOT RESPONSIBLE FOR ANY ENTRIES, ALTERATIONS, ERRORS, OMISSIONS, OR MISREPRESENTATIONS MADE BY YOU OR ANY OTHER PERSON WHO
ENTERS DATA INTO OR WHO ALTERS DATA IN THE SOFTWARE PROGRAM THAT GENERATES THE INFORMATION.
LUTRON HOPES THE QuEst-D TOOL IS HELPFUL TO YOU. WHILE LUTRON STRIVES TO ENSURE THAT THE INFORMATION PROVIDED BY THE TOOL IS ACCURATE, THE
QuEst-D TOOL AND ALL ESTIMATES ARE PROVIDED “AS IS”. LUTRON EXPRESSLY DISCLAIMS ALL WARRANTIES, WHETHER EXPRESS, IMPLIED, OR STATUTORY.
LUTRON DOES NOT ASSUME EITHER THE RISK OF THE COST OF ANY PROJECTS OR INACCURATE ESTIMATES OR ITS INFORMATION.
CODE COMPLIANCE: THE SOLUTIONS FEATURE SUMMARIZES THE LIGHTING AND RECEPTACLE CONTROL REQUIREMENTS FOR COMMERCIAL BUILDINGS.
IT IS FOR INFORMATIONAL PURPOSES ONLY. IT IS NOT MEANT TO REPLACE YOUR STATE OR LOCAL JURISDICTION’S OFFICIAL ENERGY CODE. PLEASE REFER TO
YOUR LOCAL BUILDING ENERGY CODE OR THE APPLICABLE AUTHORITY HAVING JURISDICTION OVER YOUR SPECIFIC REQUIREMENTS. ONLY THE AUTHORITY
HAVING JURISDICTION CAN GUARANTEE CODE COMPLIANCE.
[1]Note: the figures quoted in the QuEst-D tool also do not necessarily depict the actual prices charged for installation by any electrical contractor, and actual charges
may vary based on numerous factors. Labor installation times and quote estimates published by the tool are derived from NECA Manual of Labor Units 2011-2012 report (Copyright:
2011) and adjusted to apply to Lutron’s products and/or systems. Labor cost estimates are based upon: (i) NECA’s labor unit estimates over certain product/system-specific installation
activities, such as termination of low- and line-voltage wiring, and mounting control devices ; and (ii) internal Lutron product installation data generated from third-party contractor’s
information and Lutron’s own experience. Estimates do NOT cover all aspects of lighting control product/system installation, including but not limited to, the actual running of low- and
line-voltage wiring between devices and light fixtures, light fixture-installation, and any supervision time.
[2]Note: QuEst-D assumes a square footprint for each floor of the building with adjacent spaces to fully utilize the wireless coverage of each Vive hub. The system must be
designed and installed in accordance with Lutron device and system specifications. Please consult with a Lutron sales representative to discuss the details of your project and refer to
the Vive Design Guide to learn more about designing a Vive system.
© Lutron Electronics Co., Inc. Page 12 of 12