Professional Documents
Culture Documents
Low Current DC Clamp Meter: Instruction Manual
Low Current DC Clamp Meter: Instruction Manual
TⅢ
MAX
60
0 (ADIFF)
(50/60Hz)
20
1s
ec
CAUTION 2.
OFF
40
SK-7830
00
SK
EN
30
C LA
MP
14. STORAGE TEMPERATURE & HUMIDITY : Opens and closes the clamp head. When measurement, open
CAUTION 4. Do not measure AC high-frequency current. Clamp
-20℃ to 60℃, 70%RH or lower in non-condensing. clamp head 15mm or wider and close it softly. Detach fingers from
head becomes heated and could damage the
15. TEMPERATURE COEFFICIENT : Accuracy in 23℃±5℃×0.1/℃ trigger after clamping a conductor.
instrument.
16. SAFETY LEVEL : CE Marking approved (IEC-61010-1, CAT Ⅲ
1: Do not make a measurement under large
FOR SAFETY MEASUREMENTS!! 300V, CATⅠ600V and EMC Test passed.)
temperature difference. In case that the clamp meter
17. POWER SUPPLY : 1.5V R6P (AA) batteries ×2
moved into high temperature place from low
5. MEASUREMENT PROCEDURES
18. POWER CONSUMPTION : 26mA max.
temperature, turn the power on and leave it for a 5-1. PREPARATION FOR USE
To prevent an electrical shock hazard to the operator and/or 19. CONTINUOUS OPERATING TIME : Approx. 60 hours (Alkaline
while to get it used to the surrounded temperature.
damage to the instrument, read this instruction manual carefully cell), Approx. 30 hours (Manganese cell) (in 40A/200A range, 0A 2: When measurement, open clamp head 15mm or 1. INSTRUCTION MANUAL
before using the Clamp Meter. WARNINGS with the symbol input) Read INSTRUCTION MANUAL carefully to understand the
wider and close it softly. Detach fingers from trigger
on the Clamp Meter and this instruction manual are highly 20. CONDUCTOR DIAMETER : φ20mm max. specification and functions correctly. 「3. SAFETY PRECAUTIONS」
after clamping a conductor.
important. 21. DIMENSIONS & WEIGHT : 203(H)×61(W)×30(D)mm, is higly important for safety measurement.
Important Symbols Approx. 230g (including batteries)
The symbol listed in IEC 61010-1 and ISO 3864 means 22. ACCESSORIES : 1011 Carrying Case, 1.5V R6P (AA) batteries 4. NAME ILLUSTRATION 2. BATTERY
"Caution (refer to instruction manual)". ×2, Instruction Manual Before using this instrument, install 2 of 1.5V R6P (AA) batteries
WARNING : The symbol in this manual advises the user refering to 「6-1. BATTERY REPLACEMENT」. Replace them in
2-2. MEASUREMENT SPECIFICATIONS DH Key
of an electrical shock hazard that could result in serious ( 0 ADJ (DIFF) Key the same way when "BAT" lights up on LCD.
injury or even death. (23℃±5℃、<80%RH in non-condensing) Safety Line FUNCTION Switch
CAUTION : The symbol in this manual advises the user of 3. OVERLOAD INDICATION
1. DC CURRENT ( mA, A) *Accuracy after zero adjustment "OL" lights up on LCD if measurement value exceeds maximum
an electrical shock hazard that could cause injury or S K -7 8 3 0
Accuracy Resolution Max.Input 4000mA
indicatable value of each measurement range (4050 digits or 2050
material damages. Range Current
DH
0 ADJ
(DIFF )
DH
TⅢ
600
X 20
0 (AD
DIF
1sec
0A
F)
J
<
OF
mA
/ 20
0A
SK
5. POLARITY : Auto-Polarity ("ー" indication in minus) Turns the power on and selects measurement functions. After
T DC
-7 8
30
CL
AM
P M
car security system or audio settings back-up. Too much dark current
the engine, or have LCD fuel DETACH INSTRUMENT FROM CIRCUIT
WHEN TO REPLACE BATTERY.
MAX. 200A
BATTERIES : 1.5V R6P×2 26mA MAX.
OVERVOLTAGE CAT.
Ⅲ 300V CAT.Ⅰ600V
causes battery runs out, but its measurement was difficult. SK-7830 solved fig.9
this problem and make it quick and easy. fig.6
③ Start measurement with any of car lamps remain lighting.
① Leave the car engine turned off for about 15 minutes after 6-2. PERIODICAL CHECK AND CALIBRATION
setting battery cable into the measurable condition. All electric Cannot measure dark current. Periodical check and calibration is necessary to make safety
Turn the all lamps off.
components such as door lamp, room lamp, and headlight measurements and to maintain the specified accuracy. The
must be turned off. Lock the all doors if measuring car has recommended check and calibration term is once a year and after
remote-control door lock function. the repair service. This service is available at KAISE AUTHORIZED
NOTE : Leaving time is different depending on the car SERVICE AGENCY through your local dealer.
functions, especially for the cars that ECU or other electric
components keep working for a certain period of time after
turning off the engine, or have LCD fuel meter.
fig.7 70-1201-7830-2 0807
5 6 7 8