Professional Documents
Culture Documents
When using the test leads, keep your fingers behind buzzer. Auto power off feature will be across with the object
the finger guards. disabled until Switching off and turning being measured.
on the Meter again.
Disconnect circuit power and discharge all high- The measured value shows Figure 4
voltage capacitors before testing. Press HOLD to enter and exit the on the display.
To avoid harm to you or damage to the Meter from HOLD Hold mode in any mode, the Meter Note
electric shock, please do not attempt to apply higher beeps. In each range, the Meter has an input impedance of
than 600V between the terminals and grounding. 10M .This loading effect can cause measurement
Replace the battery as soon as the battery indicator Display Symbols (See Figure 2) errors in high impedance circuits. If the circuit imped
appears. With a low battery, the Meter might -ance is less than or equal to 10k , the error is
produce false readings that can lead to electric negligible (0.1% or less).
shock and personal injury. When DC voltage measurement has been completed,
When servicing the Meter, use only the replacement disconnect the connection between the testing leads
parts with the same model or identical electrical and the circuit under test, and remove the testing leads
specifications. away from the input terminals of the Meter.
Overview The internal circuit of the Meter shall not be altered C. Measuring AC Voltage (See Figure 4)
This Operating Manual covers information on safety and at will to avoid damage of the Meter and any accident. AC Voltage measurement is an auto ranging measure
cautions. Please read the relevant information carefully Soft cloth and mild detergent should be used to -ment mode.
and observe all the Warnings and Notes strictly. clean the surface of the Meter when servicing. No Note:
Warning abrasive and solvent should be used to prevent Follow the same procedure as the DC Voltage Meas
the surface of the Meter from corrosion, damage Figure 2
To avoid electric shock or personal injury, read the -urement mode. When you using UT206A to carry
“Safety Information”carefully before using the Meter. and accident. out the measurement, use SELECT button to switch
Turn the Meter off when it is not in use and take Number Symbol Description between ACV and DCV.
Model UT205A and UT206A are AC clamp multimeters
out the battery when not using for a long time. 1 Data hold is active.
(hereafter referred to as "the Meter") with remarkable D. Measuring Resistance (See Figure 5)
features: versatile functions, stable operation, low power Constantly check the battery as it may leak when 2 AC Indicator for AC Voltage.
consumption and ergonomic structural design. They it has been using for some time,replace the battery The battery is low. Warning
can measure AC/DC voltage, AC current, resistance, as soon as leaking appears. A leaking battery will 3
Warning: To avoid false readings, which
To avoid damages to the Meter or to the devices
damage the Meter. could lead to possible electric shock or
diode, continuity, frequency and temperature(UT206A),etc. personal injury, replace the battery as soon under test, disconnect circuit power and discharge
Do not use or store the Meter in an environment as the battery indicator appears. all the high-voltage capacitors before measuring
Except where noted, the descriptions and instructions in of high temperat ure, humidity,explosive, inflamm
4 % Percent: Used for duty cycle measurements. resistance.
this Operating Manual apply to both the Model UT205A -able and strong magnetic field. The performance
5 A Indicator for AC current To measure resistance, connect the Meter as follows:
/UT206A of the Meter may deteriorate after dampened
Hertz. The unit of frequency. 1. Insert the red test lead into
International Electrical Symbols Hz, kHz, Kilohertz. 1x 10 3 or 1000 hertz. the terminal andthe
Unpacking Inspection 6
MHz 6
Megahertz. 1x10 or 1,000,000 hertz. black test lead into the
Open the package case and take out the Meter. Check the AC (Alternating Current) COM terminal.
7 ,k , Ohm. The unit of resistance.
following items carefully for any missing or damaged part: 2. Set the rotary switch to .
DC (Direct Current) kilohm. 1 x 10 3 or 1000 ohms.
M 3. Connect the test leads
Item Description Qty Megaohm. 1x10 6 or 1,000,000 ohms.
AC or DC across with the object
8 The continuity buzzer is on.
1 Operating Manual 1 pc Grounding being measured. Red Black
forward voltage drop reading of 0.5V to 0.8V; however, To enter or exit REL mode: C. AC Voltage
the reverse-voltage drop reading can vary depending Use rotary switch to select the measurement function
on the resistance of other pathways between the probe Overload
before selecting REL . If measurement function Range Resolution Accuracy Remarks
tips. Protection
changes manually after REL is selected, the Meter
Connect the test leads to the proper terminals as said exits the REL mode. 4V 1mV Input impedance around 10M .
above to avoid error display.The LCD will display OL Press REL to enter REL mode, auto ranging Displays RMS value of sine
40V 10mV (1.2%+5) 600V DC
indicating diode being tested is open or polarity is turns off, and the present measurement range is wave (mean value response).
reversed. The unit of diode is Volt (V), displaying the 400V 100mV 600V AC Frequency response:
locked and stored as the stored value. All the measure
forward voltage drop readings. -ments done after will be automatically subtract this 40Hz ~ 400Hz.
600V 1V (1.5%+5)
When diode and continuity testing has been completed, stored value.
disconnect the connection between the testing leads Press REL again to exit REL mode and return D. Resistance
and the circuit under test, and remove the testing leads to common measurement mode.If you want to enter
away from the input terminals of the Meter. the auto ranging measurement mode or other ranges, Range Resolution Accuracy Overload Protection
F. Measuring Frequency and Duty Cycle please turn the rotary switch or power off the Meter
400 0.1 (1.2%+2)
and start again.
(See Figure 7) 500V DC or AC
UT205A is designed with frequency and duty cycle The SELECT Button 4k 1 (1%+2)
functions, but only frequency for UT206A. It uses for selecting the required measurement function 40k 10
To measure frequency and duty cycle, connect the when there is more than one function at one position (1%+2)
of the rotary switch. 400k 100 500V DC or AC
Meter as follows:
1. UT205A Turning on the Display Backlight 4M 1k (1.2%+2)
a. Insert the red test lead 40M 10k (1.5%+2)
Warning
into the Hz% terminal
and the black test lead In order to avoid the hazard arising from mistaken
readings in insufficient light or poor vision, please E. Diode and Continuity Test
into the COM terminal. Hz%
use Display Backlight function.
b. Set the rotary switch to Hz ; Function Range Resolution Overload Remarks
press Hz% button to switch Red Black Press and hold button for over 2 seconds to turn
between Hz and Duty cycle the Display Backlight on. Displays the nearest value
Diode 1mV
measurement mode. Press button again to turn the Display Backlight of forward voltage drop
c. Or set the rotary to ACV or Figure 7 off, otherwise it will stay on continuously. 500V DC or AC
DCV range, then press Hz% button to switch into Hz Buzzer beeps when
Sleep Mode Continuity 0.1 100
and Duty cycle measurement mode. But the accuracy
will have a little difference based on the input frequency To preserve battery life, the Meter automatically turns
off if you do not turn the rotary switch or press any button
and wave. F. Frequency (auto-ranging)
d. Connect the test leads across with the object being for around 15 minutes.
measured.The measured frequency value or duty The Meter can be activated by turning the rotary switch Range Resolution Accuracy Overload Protection Remarks
cycle value shows on the display. or pressing the effective button, it will return to Amplitude a:
working mode. 10Hz- Min (0.1%+3) 500V DC or VAC 1MHz: 300mV rms a 30V rms;
2. UT206A
10MHz 0.001Hz 1MHz: 600mV rms a 5V rms
a. Insert the red test lead into the Hz terminal and the
black test lead into the COM terminal.
General Specifications
b. Set the rotary switch to Hz. Maximum Voltage between G. Duty Cycle (Model UT205A only)
c. Connect the test leads across with the object being any Terminals and Grounding: 600V rms or 600V DC.
Range Resolution Accuracy Overload Protection
measured. The measured frequency value shows on Maximum Current Measurement: 1000A.
the display. of Transformer Jaw: 0.1%-99.9% 0.1% For reference only 500V DC or AC
Maximum Jaw Opening: 40mm.
Note
Maximum Display: Digital: 3999 H. Temperature (Model UT206A only)
When frequency and duty cycle measurement has
been completed, disconnect the connection between Overload Display: OL Range Resolution Accuracy Overload Protection
the testing leads and the circuit under test, and remove Range: Auto
o o
the testing leads away from the input terminals of the Polarity Display: Negative display: “-“ -40 C~0 C (4%+4)
Meter. Measurement Speed: Updates 3 times/second. o
1 C~400 C
o
1C
o
(2%+8) 500V DC or AC
o o o
Temperature: Operating: 0 C to +40 C (32 F to+104 F).
o
Make sure the test leads are removed from the input terminals.
Frequency resp
Operation of Hold Mode 400A 0.1A (1.5%+5) -onse 50Hz~ To replace the battery:
800A (2%+5) 60Hz.Display
Warning RMS value of
1. Turn the rotary switch of the Meter to OFF position and remove all the
To avoid possibility of electric shock, do not use 1000A 1A sine wave(mean connections from the terminals.
>800A (3%+5) value response). 2. Remove the screw from the battery compartment, and separate the battery
Hold mode to determine if circuits are without power. Figure 9
The Hold mode will not capture unstable or noisy compartment from the case bottom.
readings. B. DC Voltage 3. Remove the battery from the battery compartment.
4. Replace the battery with a new 9V battery (NEDA1604, 6F22 or 006P) .
The Hold mode is applicable to all measurement Range Resolution Accuracy Overload Protection Remarks
functions. 5. Rejoin the case bottom and battery compartment, and reinstall the screw.
400mV 100 V (0.8%+3)
Press HOLD to enter Hold mode; the Meter beeps.
Press HOLD again or turn the rotary switch to exit Hold 4V 1mV ** END **
mode; the Meter beeps. 600V DC Input impedance:
40V 10mV (0.8%+1) 600V AC
In Hold mode, is displayed. around 10M .
400V 100mV
The Use of Relative Value Mode (UT206A only)
The REL mode applies to all measurement functions 600V 1V (1%+3)
except frequency and duty cycle. It subtracts a stored
value from the present measurement value and displays
the result.
For instance, if the stored value is 20.0V and the
present measurement value is 22.0V, the reading would
be 2.0V. If a new measurement value is equal to the
stored value then display 0.0V.