You are on page 1of 6

402-00-1 Power window controller and switch 402-00-1

Chapter 402-00 Power window switch


Applicable Vehicle: CHANGAN HONOR

Catalogue
Instruction and operation

Power window controller and switch……………………………………………………………………… 402-00-2

Disassemble and installation

Power window controller and switch……………………………………………………………………… 402-00-3

Wring circuit principle

Power window controller and switch………………………………………………………………………… 402-00-4

Definition of PIN of power window

Power window controller and switch……………………………………………………………………… 402-00-5

Inspection and maintenance

Power window controller and switch……………………………………………………………………… 402-00-6

HONOR
402-00-2 Power window switch 402-00-2

DESCRIPTION AND OPERATION

Power window switch

Instruction and operation

All the vehicle window glass of this vehicle adopt the


electric elevation type, when the vehicle door glass is
required to be elevated, only the button of the glass lifter is
required to be pressed. The complete vehicle door glass
lifter buttons are installed inside the driver’s vehicle door,
the buttons on other vehicle door control the correspond-
ing vehicle door glass. The front button(Figure:1)is
locking button,when the locking button is pressed, the
ascending or descending of the other three vehicle door
glasses except the driver’s vehicle door can be locked or
released.

Button 1 locking button。


Button 2 the driver’s vehicle door glass lifter button。
Button 3 the co-driver’s vehicle door glass lifter button.。
Button 4 the riser button of the left rear vehicle door
glass.。
Button 5 the riser button of the right rear vehicle door
glass.。

The door glass lifter button, the button is pressed, when the
time is larger than 300 ms, the vehicle door glass will be
automatically descended.
When the button is lifted during the automatic descending
process, the vehicle door glass descends (the glass is
closed).。

Auto-descending function in the driver’s door.

HONOR
402-00-3 Power window switch 402-00-3

Power window switch

Disassembly and Installation

Figure one: Main power window switch Figure two: Auxiliary power window switch

Figure three: Middle door power window switch

Assembling Method:
As the pictures shows, all the switches adopt the clip-fixing way. Place the rear end part to the installing po-
sition, press the reed and finish the installation.
Disassembling Method:
When disassembling, use the tool to push the reed and uplift the switch to remove it

HONOR
402-00-3 Power window switch 402-00-3

Power window switch wiring circuit principle

Figure one: Main power window switch

Figure two: Auxiliary power window switch Figure three: Middle door power window switch

HONOR
402-00-5 Power window controller and switch 402-00-5

Definition of PIN of power window

Definition of PIN of main power window

FL Window Motor control signal(FL)


GND Grounding
B+ Battery
LOCK Lock button signal
FR Window Motor control signal(FR)
RR Window Motor control signal(RR)
AUTO Auto control of FL door window signal
RL Window Motor control signal(RL)

Definition of PIN of auxiliary power window

B Battery
FR-R Window Motor control signal(FR)
GND Grounding

Definition of PIN of middle door power window

GND Grounding
SD Middle window Motor control signal

HONOR
402-00-6 Power window switch 402-00-6

Inspection and maintenance


a. All the power window switches are not work
Step one:Inspect whether the ignition switch is turn to ON position
No,Turn the ignition switch to ON position
Yes,Turn to step two;
Step two:Inspect whether the fuse was melted in the engine compartment
Yes,Replace it;
No, Inspect the main power window switch and BCM, if they are normal, measure the voltage of
window switch control pins: 2.0—3.0 V when ascending; less than 1.0V when descending; if no voltage
shows, inspect the wiring harness or BCM
b. Inspect the wiring circuit connection of the power window (Main power window for example)

FL Window ascending: The resistance between pin FL of power window connector and GND is 4.7K ohm,
after connect to BCM, the voltage between pin FL and GND is at the range of 2.0V—3.0V

FL Window descending: The resistance between pin FL of power window connector and GND is 300 ohm,
after connect to BCM, the voltage between pin FL and GND is less than 1.0V

FL AUTO descending: The resistance between pin AUTO of power window connector and GND is 300 ohm,
after connect to BCM, the voltage between pin AUTO and GND is less than 1.0V

FR Window ascending: The resistance between pin FR of power window connector and GND is 4.7K ohm,
after connect to BCM, the voltage between pin FR and GND is at the range of 2.0V—3.0V

FR Window descending: The resistance between pin FR of power window connector and GND is 300 ohm,
after connect to BCM, the voltage between pin FR and GND is less than 1.0V

RL Window ascending: The resistance between pin RL of power window connector and GND is 4.7K ohm,
after connect to BCM, the voltage between pin RL and GND is at the range of 2.0V—3.0V

RL Window descending: The resistance between pin RL of power window connector and GND is 300 ohm,
after connect to BCM, the voltage between pin RL and GND is less than 1.0V

RR Window ascending: The resistance between pin RR of power window connector and GND is 4.7K ohm,
after connect to BCM, the voltage between pin RRand GND is at the range of 2.0V—3.0V

RR Window descending: The resistance between pin RR of main power window connector and GND is 300
ohm, after connect to BCM, the voltage between pin RR and GND is less than 1.0V

All above inspection was performed normally, if the power window switch is still have problem, please in-
spect the power window motor and harness respectively or BCM
c. Lock button wiring harness connection
Lock : Disconnect the pin LOCK of main power window switch connector and GND
Unlock: The resistance of pin LOCK of main power window switch connector and GND is 300 ohm

All above inspection was performed normally, if the other power window switches are normal, please inspect the
main power window switch and harness or BCM

HONOR

You might also like