Professional Documents
Culture Documents
Stroke 2
Repeatability 0.001* NC NC NC NC
BLUE −
Cable Oil resistant φ5 / 2 cores ●Precautions for Tool Setters for CNC Lathes…P11-2
Tensile strength 30N, Minimum bending R7 ●Precautions for Sensor Connecting…P13-2
LED lamp Default : LED ON / Operating : LED OFF ●Cable Options…P13-4
Operating temperature range 0°
C-60°C (Ice-free) ●Technical Guide…P14-1
* Repeatability of the tool setter alone
11-3 No.10-2E
H4A Linear Type Tool Setter Series for CNC Lathes
www.metrol.co.jp/en
20
(40)
23
34
4 2
20 4-φ4.5
3
23 LED lamp
34
5
10.5
4-Tungsten carbide φ5
(49.5)
30
φ16.5
5
B
●Protective covers
9
O-Ring S20
Select a type that prevents coolant
-0.10
from entering through the gap and
φ23 -0.15 accumulating inside.
φ16
U type (standard)
Upward, sideways
Gap
1-Direction □ ① □⑤
2-Direction □ ① ② □①③ □①⑤
No. of detecting
3-Direction □ ① ② ③ □①②⑤ □①③⑤
direction
4-Direction □ ① ② ③ ④ □①②③⑤
5-Direction □ ① ② ③ ④ ⑤
Cable options
Company
How to order
1. Spec sheet 2. Selection 3. Confirmation 4. Order
Dept. / Title
E-mail E-mail E-mail
Name
Quotation
&
Address Order
“T24E-04-19”
TEL
Please fill out the The drawing of Check the drawing The quotation is sent
specification sheet specific model based to select/confirm and you can place
FAX and send to Metrol. on spec sheet is sent . the specific model. an order.
E-mail: touchsensor@metrol.co.jp
E-mail PDF sheet is available for download at www.metrol.co.jp/en
FAX: +81-42-528-1442 touchsensor@metrol.co.jp
- Copy this page and use repeatedly. -
No.10-2E
11-4
Tool Setter Series for CNC Lathes
Tool Setter for CNC Lathes www.metrol.co.jp/en
■Tool setters for CNC lathe are used for precise tool
bit positioning, and detection of the wear and
breakage.
■A type which opposite side size of the contact has
been reduced to the maximum and can swing in 4
directions.
11-5 No.10-2E
H4E Swing Contact Type Tool Setter Series for CNC Lathes
www.metrol.co.jp/en
H4E 4-φ4.5
Spot facing φ7.5 D4
0.01/7
0.01/5 A B
21.2
15
38
7
5
φ4
Contact 7
0.01/7
3
0.01/7 A
0.01/5 B
5
(28.2)
37
8.8
21.2
B
8.5
-0.10
φ23 -0.15
Cable options
Company
How to order
1. Spec sheet 2. Selection 3. Confirmation 4. Order
Dept. / Title
E-mail E-mail E-mail
Name
Quotation
&
Address Order
“T24E-04-19”
TEL
Please fill out the The drawing of Check the drawing The quotation is sent
specification sheet specific model based to select/confirm and you can place
FAX and send to Metrol. on spec sheet is sent . the specific model. an order.
E-mail: touchsensor@metrol.co.jp
E-mail PDF sheet is available for download at www.metrol.co.jp/en
FAX: +81-42-528-1442 touchsensor@metrol.co.jp
- Copy this page and use repeatedly. -
No.10-2E
11-6