Professional Documents
Culture Documents
)The maximum stress to which a standardized test specimen may be subjected without a permanent
deformation..
a.)Endurance Limit
b.)Elastic limit
c.)Proportional limit
d.)Plastic limit
5.)it is the characteristic of exhibiting different properties when tested in different directions
a.)Allotropy
b.)Isentropic
c.)Anistropy
d.)Isotropic
6.)It is one in which specimen supported at both ends as a simple beam is broken by the impact strength
of the metal
a.)Charpy Test
b.)Rockwell test
c.)Izod test
d.)Universal test
7.)Steel that has been deoxidized with a strong deoxidizing agent such as silicon or aluminum in order to
eliminate a reaction between the carbon and oxygen during solidification
a.)Carbon Steel
b.)Killed Steel
c.)Tool Steel
d.)Structural Steel
8.)Involves the loss of ductility because of a physical or chemical change of the material is known as
a.)Embrittlement
b.)Cold Shortness
c.)Pitting
d.)Decarburization
14.)Which of the following chisels would be used for cutting oil grooves
a.)Diamond point chisel
b.)Cold chisel
c.)Round nose chisel
d.)Hot chisel
25.)Which of the following contact points metals has highest melting point
a.)Silver
b.)Tungsten
c.)Gold
d.)Copper
28.)Which of the following metals gets deposited to provide an undercut for chromium
a.)Copper
b.)Silver
c.)Bronze
d.)Lead
32.)Hands taps are provided in sets of three…Which of the following set of three..
a.)Taper, plug and end
b.)Taper,plug and bottom
c.)Short,taper and bottom
d.)Short, medium and long
34.)Which of the following size of the drill is used in preparing to tap a hole.
a.)Equal to the size of the tap
b.)Larger than the size of the trap
c.)Smaller than the size of the tap
d.)Non of these
36.)When preparing to tap a hole for a pipe fitting the size of the drill will be.
a.)Larger than the tap size
b.)Smaller than the tap size
c.)Equal to the tap size
d.)None of these
38.)How do you call the tool used when cutting a hole in the side of a round piece of metal?
a.)Vise
b.)V block
c.)Jaw holder
d.)Chuck
41.)Select from the conductors below that has the least electrical conductivity.
a.)Lead
b.)Tin
c.)Zinc
d.)Aluminum
45.)Any heating and cooling of steel that produces a rounded or globular form of carbide.
a.)Spheroidizing
b.)malleability
c.)Graphitizing
d.)Normalizing
46.)Steel that has been hammered rolled or drawn in the process of manufacture.
a.)Wrought Steel
b.)Rimmed Steel
c.)Killed Steel
d.)Stainless steel
50.)If you wanted to check the face of a pump slide valve or other flat-faced valve,you could check for
truenee on a:
a.)Flat Board
b.)Pieces of glass
c.)Surface plate
d.)Bearing plate
Answers:
1.)Elastic limit
2.)Stiffness
3.)Artificial Aging
4.)Brittleness
5.)Anistropy
6.)Charpy test
7.)Killed steel
8.)Embrittlement
9.)Soft Iron
10.)Nickel,Cobalt and steel
11.)National Coarse
12.)National File
13.)Reamer
14.)Round nose chisel
15.)half round
16.)File card
17.)#80
18.)Z
19.)Shank
20.)All three mentioned
21.)Graphite
22.)all of these
23.)Mica
24.)Mercury-oxide
25.)Gold
26.)Silver
27.)Silicon sheet steel
28.)Bronze
29.)Dilute potassium hydroxide
30.)Square
31.)Tap
32.)Taper,plug and bottom
33.)Taper
34.)Smaller than the size of the tap
35.)Tapered
36.)Equal to the size of the tap
37.)Monel
38.)V block
39.)Margins
40.)Silver zinc
41.)Lead
42.)carbon
43.)Any of these
44.)Silver
45.)Spheroidizing
46.)Wrought Steel
47.)Cobalt
48.)Monel
49.)Copper
50.)Surface plate