Professional Documents
Culture Documents
P/N: FF-1002-1
DESCRIPTION:
S/N: VB172-(1-2199)
Certification For:
SPACER ASSY 6’’ LONG. 2’’- 1502 (M x F)
Part No. FF-1002-1
W.O. # VB172
S/N: VB172-(1-2199)
BILL OF MATERIALS
CERTIFICATE OF CONFORMANCE
MATERIAL CLASS: AA
This is to certify that item(s) referenced above have been designed, manufactured, and shipped in
compliance with the requirements determined in the Tech-Seal International Inc. Quality Assurance
Manual Rev. C, dated January 1, 2017, based on API-Q1 9th Edition, ANSI/ISO/ASQ-Q9001:2015,
and tested in accordance with API 6A, 20th edition. All applicable design, calculations, analysis and
engineering specifications, procedures, and otherwise applicable purchase orders abide by these
requirements.
Tech-Seal International
Hydrostatic Test
All above stated material tested in accordance with API-6A, Edition 20.
The material chemistry, heat treatment and mechanical testing described below was furnished on Certifications by:
%C %Mn %P %S %Si %Cu %Ni %Cr %Mo %Ca %V %N %Ti %Al %W %Pb
.309 .65 .010 .005 .26 .15 .11 1.16 .23 .0009 .042 .0034 .023 .0001
MECHANICAL PROPERTIES CHARPY IMPACT PROPERTIES
ASTM A-370 REQUIREMENT ACTUAL 10MM x 10MM ACTUAL ACTUAL
.2% Offset Yield Strength (PSI) 110, 000 MIN 120 224.79 PSI Temperature (oF or oC) -75 oF
Tensile Strength (PSI) (.492 Dia) 125, 000 MIN 136 670.75 PSI Foot Pounds 30 , 29 , 31
% Elongation in 2" Gage Length 17% MIN 18.10 % CVN ORIENTATION Transverse Longitudinal
QTC Hardness (Two Brinell Readings) 277-277 HBW QTC size : 4.0” x 4.0” x 8.0” QTC Lot Number : 18A100
Second Temper/Age
HARDNESS
COMPONENT HARDNESS : 277-321 HBW NUMBER OF PIECES CHECKED: 1200
We hereby certify that the part(s) described above has been tested and complies with the terms of the order.This certificate meets the requirements of EN 10204,
Type 3.1, and is validated by an authorized representative, independent of manufacturing operations.
CERTIFIED BY: NGO DAC TRI POSITION TITLE:
TECHNICAL MANAGER
The material chemistry, heat treatment and mechanical testing described below was furnished on Certifications by:
%C %Mn %P %S %Si %Cu %Ni %Cr %Mo %Ca %V %Nb %Ti %Al %W %Pb
.33 .57 .013 .005 .28 .06 .05 1.09 .22 .0010 .037 .038
.2% Offset Yield Strength (PSI) 110, 000 MIN 128, 489.46 PSI Temperature (oF or oC) -75 oF
Tensile Strength (PSI) (.501 Dia) 125, 000 MIN 142, 264.00 PSI Foot Pounds 57 , 49 , 61
% Elongation in 2" Gage Length 17% MIN 20.85% CVN ORIENTATION Transverse Longitudinal
QTC Hardness (Two Brinell Readings) 285-285 HBW QTC Size: 4.0”x 4.0” x 8.0” QTC Lot Number: 18E361
Second Temper/Age
HARDNESS
COMPONENT HARDNESS : 277-321 HBW
NUMBER OF PIECES CHECKED: 1600
We hereby certify that the part(s) described above has been tested and complies with the terms of the order.This certificate meets the requirements of EN 10204,
Type 3.1, and is validated by an authorized representative, independent of manufacturing operations.
CERTIFIED BY: NGO DAC TRI POSITION TITLE:
TECHNICAL MANAGER
The material chemistry, heat treatment and mechanical testing described below was furnished on Certifications by:
%C %Mn %P %S %Si %Cu %Ni %Cr %Mo %Ca %V %Nb %Ti %Al %W %Pb
.32 .58 .010 .003 .28 .06 .05 1.08 .23 .0010 .036 .038
.2% Offset Yield Strength (PSI) 110, 000 MIN 116, 103.25 PSI Temperature (oF or oC) -75 oF
Tensile Strength (PSI) (.500 Dia) 125, 000 MIN 137, 691.68 PSI Foot Pounds 52 , 66 , 59
% Elongation in 2" Gage Length 17% MIN 18.75% CVN ORIENTATION Transverse Longitudinal
QTC Hardness (Two Brinell Readings) 277-277 HBW QTC Size: QTC Lot Number: The same lot
Normalize B: A: B: A:
0 O 0
Austenitize / Solution Annealed 1598 F 0.95 WATER B: 82 F 1598 F 0.95 WATER B: 82 OF
O
A: 82 F A: 82 OF
AIR AIR
First Temper / Age 1130 0F 1.45 1116 0F 1.45
Second Temper/Age
HARDNESS
COMPONENT HARDNESS : 277-321 HBW
NUMBER OF PIECES CHECKED: 1500
We hereby certify that the part(s) described above has been tested and complies with the terms of the order.This certificate meets the requirements of EN 10204,
Type 3.1, and is validated by an authorized representative, independent of manufacturing operations.
CERTIFIED BY: NGO DAC TRI POSITION TITLE:
TECHNICAL MANAGER
The material chemistry, heat treatment and mechanical testing described below was furnished on Certifications by:
CHEMICAL ANALYSIS
%C %Mn %P %S %Si %Cu %Ni %Cr %Mo %Ca %V %Nb %Ti %Al %W %Pb
.3210 .5458 .0163 .0095 .1886 .0127 .0240 1.0618 .2276 .0024 .0028 .0012 .0292
o o
.2% Offset Yield Strength (PSI) 110, 000 MIN 124,924.81 PSI Temperature ( F or C) -50 oF
Tensile Strength (PSI) (.252 Dia) 125, 000 MIN 140,916.52 PSI Foot Pounds 61 , 60 , 70
% Elongation in 1" Gage Length 15% MIN 19.40 % PSI CVN ORIENTATION Transverse Longitudinal
QTC Hardness (Two Brinell Readings) 285-285 HBW QTC Size: Ф 96 x 130mm QTC Lot number:
Normalize B: A: B: A:
O O
Austenitize / Solution Annealed B: F B: F
O
A: F A: OF
Second Temper/Age
HARDNESS
COMPONENT HARDNESS : 269-331 HBW NUMBER OF PIECES CHECKED: 40000
We hereby certify that the part(s) described above has been tested and complies with the terms of the order. This certificate meets the requirements of EN 10204,
Type 3.1, and is validated by an authorized representative, independent of manufacturing operations.
CERTIFIED BY: NGO DAC TRI POSITION TITLE:
TECHNICAL MANAGER
The material chemistry, heat treatment and mechanical testing described below was furnished on Certifications by:
CHEMICAL ANALYSIS
%C %Mn %P %S %Si %Cu %Ni %Cr %Mo %Ca %V %Nb %Ti %Al %W %Pb
.3182 .5468 .0174 .0092 .2061 .0103 .0214 1.0577 .2245 .0019 .0023 .0012 .0307
o o
.2% Offset Yield Strength (PSI) 110, 000 MIN 123,607.16 PSI Temperature ( F or C) -50 oF
Tensile Strength (PSI) (.248 Dia) 125, 000 MIN 139,790.93 PSI Foot Pounds 65 , 70 , 66
% Elongation in 1" Gage Length 15% MIN 19.90 % PSI CVN ORIENTATION Transverse Longitudinal
QTC Hardness (Two Brinell Readings) 285-285 HBW QTC Size: Ф 96 x 130mm QTC Lot number:
Normalize B: A: B: A:
O O
Austenitize / Solution Annealed B: F B: F
O
A: F A: OF
Second Temper/Age
HARDNESS
COMPONENT HARDNESS : 269-331 HBW NUMBER OF PIECES CHECKED: 18000
We hereby certify that the part(s) described above has been tested and complies with the terms of the order. This certificate meets the requirements of EN 10204,
Type 3.1, and is validated by an authorized representative, independent of manufacturing operations.
CERTIFIED BY: NGO DAC TRI POSITION TITLE:
TECHNICAL MANAGER
The material chemistry, heat treatment and mechanical testing described below was furnished on Certifications by:
CHEMICAL ANALYSIS
%C %Mn %P %S %Si %Cu %Ni %Cr %Mo %Ca %V %Nb %Ti %Al %W %Pb
.3206 .5534 .0167 .0089 .2141 .0090 .0225 1.0490 .2203 .0025 .0024 .0013 .0336
o o
.2% Offset Yield Strength (PSI) 110, 000 MIN 120,872.43 PSI Temperature ( F or C) -50 oF
Tensile Strength (PSI) (.253 Dia) 125, 000 MIN 136,889.29 PSI Foot Pounds 64, 73 , 72
% Elongation in 1" Gage Length 15% MIN 21.40 % PSI CVN ORIENTATION Transverse Longitudinal
QTC Hardness (Two Brinell Readings) 277-277 HBW QTC Size: Ф 96 x 130
Normalize B: A: B: A:
O O
Austenitize / Solution Annealed B: F B: F
O
A: F A: OF
Second Temper/Age
HARDNESS
COMPONENT HARDNESS : 269-331 HBW NUMBER OF PIECES CHECKED: 12000
We hereby certify that the part(s) described above has been tested and complies with the terms of the order. This certificate meets the requirements of EN 10204,
Type 3.1, and is validated by an authorized representative, independent of manufacturing operations.
CERTIFIED BY: NGO DAC TRI POSITION TITLE:
TECHNICAL MANAGER
The material chemistry, heat treatment and mechanical testing described below was furnished on Certifications by:
CHEMICAL ANALYSIS
%C %Mn %P %S %Si %Cu %Ni %Cr %Mo %Ca %V %Nb %Ti %Al %W %Pb
.3252 .5576 .0145 .0060 .2058 .0098 .0249 1.0548 .2249 .0016 .0013 .0366
o o
.2% Offset Yield Strength (PSI) 110, 000 MIN 124, 785.53 PSI Temperature ( F or C) -50 oF
Tensile Strength (PSI) (.249 Dia) 125, 000 MIN 139, 548.56 PSI Foot Pounds 64 , 62 , 66
% Elongation in 1" Gage Length 15% MIN 17.90 % PSI CVN ORIENTATION Transverse Longitudinal
QTC Hardness (Two Brinell Readings) 277-277 HBW QTC Size: Ф 96mm x 130mm
Normalize B: A: B: A:
O O
Austenitize / Solution Annealed B: F B: F
O
A: F A: OF
Second Temper/Age
HARDNESS
COMPONENT HARDNESS : 269-331 HBW NUMBER OF PIECES CHECKED: 46000
We hereby certify that the part(s) described above has been tested and complies with the terms of the order. This certificate meets the requirements of EN 10204,
Type 3.1, and is validated by an authorized representative, independent of manufacturing operations.
CERTIFIED BY: NGO DAC TRI POSITION TITLE:
TECHNICAL MANAGER
The material chemistry, heat treatment and mechanical testing described below was furnished on Certifications by:
%C %Mn %P %S %Si %Cu %Ni %Cr %Mo %Ca %V %Nb %Ti %Al %W %Pb
.33 .60 .010 .003 .28 .07 .05 1.08 .23 .0009 .038 .038
.2% Offset Yield Strength (PSI) 110, 000 MIN 129, 394.47 PSI Temperature (oF or oC) -75 oF
Tensile Strength (PSI) (.499 Dia) 125, 000 MIN 142, 743.24 PSI Foot Pounds 92 , 77 , 77
% Elongation in 2" Gage Length 17% MIN 20.50% CVN ORIENTATION Transverse Longitudinal
QTC Hardness (Two Brinell Readings) 285-285 HBW QTC Size: 4.0”x 4.0” x 8.0” QTC Lot Number: 18E110
Second Temper/Age
HARDNESS
COMPONENT HARDNESS : 277-321 HBW
NUMBER OF PIECES CHECKED: 9500
We hereby certify that the part(s) described above has been tested and complies with the terms of the order.This certificate meets the requirements of EN 10204,
Type 3.1, and is validated by an authorized representative, independent of manufacturing operations.
CERTIFIED BY: NGO DAC TRI POSITION TITLE:
TECHNICAL MANAGER
The material chemistry, heat treatment and mechanical testing described below was furnished on Certifications by:
%C %Mn %P %S %Si %Cu %Ni %Cr %Mo %Ca %V %Nb %Ti %Al %W %Pb
.32 .60 .009 .005 .30 .07 .15 1.08 .23 .0011 .039 .040
.2% Offset Yield Strength (PSI) 110, 000 MIN 116, 822.29 PSI Temperature (oF or oC) -75 oF
Tensile Strength (PSI) (.501 Dia) 125, 000 MIN 135, 238.51 PSI Foot Pounds 38 , 28 , 27
% Elongation in 2" Gage Length 17% MIN 19.65% CVN ORIENTATION Transverse Longitudinal
QTC Hardness (Two Brinell Readings) 277-277 HBW QTC Size: 4.0”x 4.0” x 8.0” QTC Lot Number: 18E110
Second Temper/Age
HARDNESS
COMPONENT HARDNESS : 277-321 HBW
NUMBER OF PIECES CHECKED: 8700
We hereby certify that the part(s) described above has been tested and complies with the terms of the order.This certificate meets the requirements of EN 10204,
Type 3.1, and is validated by an authorized representative, independent of manufacturing operations.
CERTIFIED BY: NGO DAC TRI POSITION TITLE:
TECHNICAL MANAGER
The material chemistry, heat treatment and mechanical testing described below was furnished on Certifications by:
%C %Mn %P %S %Si %Cu %Ni %Cr %Mo %Ca %V %Nb %Ti %Al %W %Pb
.31 .58 .009 .005 .28 .05 .04 1.07 .23 .0014 .04 .04
.2% Offset Yield Strength (PSI) 110, 000 MIN 125, 372.59 PSI Temperature (oF or oC) -75 oF
Tensile Strength (PSI) (.251 Dia) 125, 000 MIN 139, 422.23 PSI Foot Pounds 70 , 77 , 80
% Elongation in 1" Gage Length 17% MIN 20.80% CVN ORIENTATION Transverse Longitudinal
QTC Hardness (Two Brinell Readings) 277-277 HBW QTC Size: QTC Lot Number: The same lot
Second Temper/Age
HARDNESS
COMPONENT HARDNESS : 277-321 HBW
NUMBER OF PIECES CHECKED: 10600
We hereby certify that the part(s) described above has been tested and complies with the terms of the order.This certificate meets the requirements of EN 10204,
Type 3.1, and is validated by an authorized representative, independent of manufacturing operations.
CERTIFIED BY: NGO DAC TRI POSITION TITLE:
TECHNICAL MANAGER
The material chemistry, heat treatment and mechanical testing described below was furnished on Certifications by:
%C %Mn %P %S %Si %Cu %Ni %Cr %Mo %Ca %V %Nb %Ti %Al %W %Pb
.32 .59 .009 .003 .29 .06 .04 1.08 .22 .0013 .037 .038
.2% Offset Yield Strength (PSI) 110, 000 MIN 118, 077.95 PSI Temperature (oF or oC) -75 oF
Tensile Strength (PSI) (.503 Dia) 125, 000 MIN 135, 301.63 PSI Foot Pounds 48 , 49 , 61
% Elongation in 2" Gage Length 17% MIN 20.30% CVN ORIENTATION Transverse Longitudinal
QTC Hardness (Two Brinell Readings) 277-277 HBW QTC Size: 4.0”x 4.0” x 8.0” QTC Lot Number: 18E110
Second Temper/Age
HARDNESS
COMPONENT HARDNESS : 277-321 HBW
NUMBER OF PIECES CHECKED: 10600
We hereby certify that the part(s) described above has been tested and complies with the terms of the order.This certificate meets the requirements of EN 10204,
Type 3.1, and is validated by an authorized representative, independent of manufacturing operations.
CERTIFIED BY: NGO DAC TRI POSITION TITLE:
TECHNICAL MANAGER
The material chemistry, heat treatment and mechanical testing described below was furnished on Certifications by:
%C %Mn %P %S %Si %Cu %Ni %Cr %Mo %Ca %V %Nb %Ti %Al %W %Pb
.32 .59 .010 .003 .29 .07 .05 1.09 .24 .0012 .041 .042
.2% Offset Yield Strength (PSI) 110, 000 MIN 113, 432.67 PSI Temperature (oF or oC) -75 oF
Tensile Strength (PSI) (.501 Dia) 125, 000 MIN 130, 439.92 PSI Foot Pounds 85 , 69 , 61
% Elongation in 2" Gage Length 17% MIN 20.40% CVN ORIENTATION Transverse Longitudinal
QTC Hardness (Two Brinell Readings) 277-277 HBW QTC Size: 4.0”x 4.0” x 8.0” QTC Lot Number: 18E110
Second Temper/Age
HARDNESS
COMPONENT HARDNESS : 277-321 HBW
NUMBER OF PIECES CHECKED: 10400
We hereby certify that the part(s) described above has been tested and complies with the terms of the order.This certificate meets the requirements of EN 10204,
Type 3.1, and is validated by an authorized representative, independent of manufacturing operations.
CERTIFIED BY: NGO DAC TRI POSITION TITLE:
TECHNICAL MANAGER
The material chemistry, heat treatment and mechanical testing described below was furnished on Certifications by:
%C %Mn %P %S %Si %Cu %Ni %Cr %Mo %Ca %V %Nb %Ti %Al %W %Pb
.32 .58 .011 .005 .30 .09 .06 1.09 .24 .0012 .041 .043
.2% Offset Yield Strength (PSI) 110, 000 MIN 135, 288.75 PSI Temperature (oF or oC) -75 oF
Tensile Strength (PSI) (.500 Dia) 125, 000 MIN 147, 772.51 PSI Foot Pounds 35 , 41 , 36
% Elongation in 2" Gage Length 17% MIN 20.25% CVN ORIENTATION Transverse Longitudinal
QTC Hardness (Two Brinell Readings) 293-293 HBW QTC Size: 4.0”x 4.0” x 8.0” QTC Lot Number: 18G900
Second Temper/Age
HARDNESS
COMPONENT HARDNESS : 277-321 HBW
NUMBER OF PIECES CHECKED: 10400
We hereby certify that the part(s) described above has been tested and complies with the terms of the order.This certificate meets the requirements of EN 10204,
Type 3.1, and is validated by an authorized representative, independent of manufacturing operations.
CERTIFIED BY: NGO DAC TRI POSITION TITLE:
TECHNICAL MANAGER