Professional Documents
Culture Documents
- Added error for not answering the "does the material contain recyclate?" question for materials of
classification 5.x if their weight is >5g.
- Added errors for entering a range for either post-industrial or post-consumer recyclate where the
maximum value exceeds the minimum value by more than 20%.
More than one child with "rest" You have 2 or more children where
defined “rest” has been used as portion
Sum of fixed values and range The Percentages sum to > 100%
values too big
Sum of fixed values and range The Percentages sum to < 100%
values too small (probably because you’ve been
using an MSDS sheet for your data)
Non basic substances must be There are paths from the top of the
decomposed further tree to the bottom that do not
terminate in a basic substance (blue
triangle)
No percentage specified! Something has been added without a
portion being defined
Calculation yields a rest of 0%! Something is wrong with the
percentages so that you have an
item with “rest” with value 0
The referenced datasheet is not You have attached a datasheet that
internally released does not have a whole number
version
The referenced module ist not You have attached a module that
internally released does not have a whole number
version
This Classification can not be used You are trying to release a material
anymore. that was initially created with a
material classification that is no
longer valid
No symbol specified (mandatory for You trying to release a material that
this material classification) now requires a material symbol
(thermoplastics and elastomers)
Replace the default name of this You’ve left the system generated
datasheet/module by a meaningful name (e.g. “Component_133479”)
name
Recyclate information has not been You need to give an answer on the
entered Recyclate question
Instead of the forwarded version, the A forward version of an accepted
original MDS that your company MDS must not be referenced in the
accepted must be used. tree.
The chemical presence type has to For process chemicals, the presence
be specified. type within the material has to be
selected (for concentration > 0.1%).
The measured weight per item needs You have not stated a weight on a
to be higher than zero. component
The substance has been You are using an older material that
deactivated, while references in contains a substance that has been
previously created modules/MDSs deactivated
are still valid and can be sent.
The material contains deactivated You are using an older material that
substances. contains a substance that has been
deactivated
Ions do not exist in a pure manner see sheet SC90, check type 3
and cannot be an individual content
of a material.
This substance wildcard is only The wildcard is only allowed in
allowed within a preliminary MDS preliminary material MDSs. It must
material. not be used in materials for final
(PPAP/Initial Sample Report) MDSs.
Click on Correct and the system will take you to the ERROR No
area where you can add the quantity
The error message will tell you the parent that has the ERROR No
problem, you will have to investigate which children
have the problem
The error message will tell you the parent that has the ERROR No
problem, you will have to investigate which children
have the problem
The error message will tell you the parent that has the ERROR No
problem, you will have to investigate which children
have the problem
The error message will tell you the parent that has the ERROR No
problem, you will have to investigate which children
have the problem
Define and release your materials ERROR No
Click on Correct and the system will take you to the ERROR No
area and add the percentage
The error message will tell you the child that has the ERROR No
problem, you will have to investigate which other
children have the problem
Correct will take you to the tree where you can get the ERROR No
ID of the unreleased datasheet. Click on the modify
button in the details section to release it and come back
to this datasheet
See above ERROR No
Edit the material classification and select a new one ERROR, if the material No
is not productive
Edit the material symbol field and give it a valid material ERROR, if the material No
symbol (you may use the symbol wizard to generate a is not productive
valid symbol)
Click on Correct and the system will take you to the ERROR No
area where you can uncheck confidential
Edit the description and add in meaningful name ERROR, if node is not a No
reference
Click on Correct and the system will take you to the ERROR No
area where you can add the information
Replace the forward version with the accepted MDS. ERROR No
Edit the semi-component and enter the specific weight. ERROR, if the semi- No
component is not
productive
Click on Correct and the system will take you to the WARNING (May 9th, Yes
area where you can make the correction 2008: MDSs released by
the IMDS Steering
Committee have been
excluded)
Go to the material in question and add more detail – WARNING (May 9th, Yes
however, if this is a master batch, it may not be 2008: MDSs released by
necessary. the IMDS Steering
Committee have been
excluded)
Go to the component or semi-component in question WARNING Yes
and add a component or semi-component on the fly and
add the rest underneath
Click on Correct and the system will take you to the ERROR Yes
area where you can make the correction
Select either "Yes" or "No" for the "Does the material ERROR No
contain recyclate?" question.
Click on Correct and the system will take you to the ERROR Yes
area where you can make the correction
Click on Correct and the system will take you to the ERROR Yes
area where you can make the correction
Change the min or max value so the difference is not ERROR No
greater than 20%.
(WARNING from
September 25th, 2019)
Change the min or max value so the difference is not ERROR No
greater than 20%.
(WARNING from
September 25th, 2019)
The error message will tell you the parent that has the WARNING Yes
problem, you will have create a new version of the
material and correct, then remove this material and add
in new one
Click on Correct and the system will take you to the ERROR, if component is Yes
area where you can make the correction not a reference, else
WARNING
Go to the component where the material is first attached ERROR, if the mds Yes
and answer the question (may require going to another containing the
component) component is not
productive, else
WARNING
Contact your supplier and ask for a new version of the WARNING Yes
MDS with an updated reference.
The error message will tell you the parent that has the ERROR Yes
problem, you will have to create a new version of the
material and correct, then remove this material and add
in new one – may require several iterations to get to the
top of the tree.
Contact your supplier and ask for a new version of the WARNING Yes
MDS with an updated reference.
ERROR Yes
ERROR Yes
See instructions following this section – may require ERROR, if own Yes
several iterations of copy/new version and release component, or OEM,
else WARNING
Choose another available application for the PAH ERROR, if own Yes
substance in the elastomer material. component, or OEM,
else WARNING
See instructions following this section – may require ERROR, if application Yes
several iterations of copy/new version and release can be changed (in edit
mode), else WARNING
see sheet SC90, check type 1 WARNING Yes
Replace the referenced module or mark it as "not WARNING Yes (within own
obsolete" Modules(MDSs)
Replace the referenced datasheet or mark it as "not WARNING Yes (within own
obsolete" Modules(MDSs)
For data modified
for OEM
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
Yes
Yes
No
No
No
No
Yes
No
No
No
No
Yes
No
No
No
Yes
Yes
No
No
No
No
No
No
No
No
No
No
No
No
No
No
Message Meaning
Contact must be specified The contact person was not selected
yet and is undefined
For data modified
Fix Type for OEM
Select the contact person ERROR No
Message Meaning
Item- /Mat.-No. has to be specified!
You have not placed information in a
required field
Material-No. has to be specified! You have not placed information in a
required field
Part/Item No. has to be specified! You have not placed information in a
required field
the company was deleted Your recipient company is no longer
available
You cannot send or propose an MDS You are trying to send to another Org
to your own company or one of its Unit of the same roof company
org-units.
A new recipient part number or This is violation of Rec001 Rule
supplier code requires a new MDS ID 3.2.2.A.
You have created a new version of
an already sent/proposed MDS, but
used a new part/item number or
supplier code for a recipient org unit
who has already received a previous
version.
Please register at least a public norm You have a material with no norm or
or a Toyota inhouse norm standard. This material is referenced
in a (semi)component with a weight
of at least 5g.
Please enter a correct index of the
Renault part.
E-mail address of the RENAULT
DESIGNER in charge of the part has
to be entered.
Please enter a correct index of the
standard.
Substance and Material cannot be a On the level below a material there
child of a material at the same level. can only be substances or materials
but no mixture of both.
The recipient does not accept
Preliminary MDSs.
Please confirm that all referenced When sending an MDS to Nissan the
Wildcard Substances do not refer to checkbox "Referenced Wildcard
GADSL Substances. Substances do not refer to GADSL
Substances" needs to be selected.
Either correct the part/item number and/or supplier code WARNING common
or create a new MDS and use the part/item number and
supplier code when adding the recipient there.
Either correct the part/item number and/or supplier code WARNING common
or create a new Version of one of the listed MDS IDs
and use the part/item number and supplier code when
adding the recipient there.
Create a new version of the MDS IDs that have WARNING common
previously been sent/proposed to the recipients. In
these MDSs you can reference the original accepted
MDS.
Use the "Apply application modifications to all OEMs in WARNING common, any
the recipient list" function to apply the changes you OEM
made for one OEM to all other OEMs in the recipient
list.
Use the "Apply polymeric parts marking modifications to WARNING common, any
all OEMs in the recipient list" function to apply the OEM
changes you made for one OEM to all other OEMs in
the recipient list.
Modify and correct ERROR Daimler AG /
Chrysler LLC
Modify and correct ERROR Daimler AG /
Chrysler LLC
Create component and add semi-component or ERROR FORD
materials beneath. If expecting Material, create similar
structure
ERROR Renault
ERROR Renault
ERROR Renault
ERROR Renault
ERROR Renault
ERROR Nissan
WARNING Nissan
No
No
No
No
No
No
No
Exclusively
Exclusively
No
No
No
No
No
No
Yes
No
No
No
No
No
No
No
No
No
No
Meldung Bedeutung
Gewicht muss größer als 0 sein Sie haben vergessen, einem
referenzierten Werkstoff oder
Halbzeug ein Gewicht zuzuordnen.
Die Anzahl muß mindestens ein Sie haben vergessen, für ein
Stück betragen! hinzugefügtes Teil die Anzahl
anzugeben.
Mehr als ein Rest definiert Sie haben 2 oder mehr Referenzen,
wo „Rest“ als Anteil angegeben
wurde
Summe von Festwerten und Die Prozentzahlen ergeben > 100%
Intervallwerten zu gross
Das referenzierte Modul ist nicht Sie haben ein MDB referenziert, das
intern freigegeben keine volle Versions-Nummer hat,
sondern *.0x
Diese Klassifizierung darf nicht mehr Sie versuchen, einen Werkstoff mit
verwendet werden. einer Klassifizierung freizugeben, die
nicht mehr gültig ist
Kein Symbol angegeben (Pflichtfeld Sie versuchen, einen Werkstoff
bei dieser Werkstoffklassifizierung) freizugeben, der jetzt ein Werkstoff-
Symbol erfordert.
Mehr als 10% nicht definierte Vorgaben der Richtlinie 001 werden
Reinstoffe. (“Nicht definiert” sind verletzt (mehr als 10% nicht-
Reinstoff-Joker oder vertrauliche spezifizierte Reinstoffe verwendet)
Reinstoffe).
Der Unterschied zwischen dem The difference between the min and
Minimumwert und dem Maximumwert max portion of recyclate content is
für den Rezyklatanteil aus too large.
Altmaterialien überschreitet den
erlaubten Wert von 20
Reinstoff und Werkstoff können kein Auf der Ebene unter einem Werkstoff
Bestandteil eines Werkstoffes auf können Reinstoffe oder Werkstoffe
derselben Ebene sein. referenziert sein, aber keine
Mischung aus beidem.
Das gemessene Einzelgewicht muß Sie haben für ein Teil kein Gewicht
größer als 0 sein. angegeben
Frage nach Kennzeichnung der Sie haben die Frage nach der
Polymerwerkstoffe wurde nicht Polymerkennzeichnung nicht
beantwortet beantwortet
Vorläufige MDB dürfen nur in einem Ein Baum sollte keine Knoten
MDB/Modul referenziert werden, das enthalten, die „Vorläufige MDB“ sind,
ebenfalls vorläufig ist. wenn der oberste Knoten kein
„Vorläufiges MDB“ ist.
Dieses Element Ein Element kann nicht mehr
(MDB/Modul/Reinstoff) wurde verwendet werden (z.B. eine
während des Kopiervorgangs als gelöschte Referenz). Deshalb wir es
Platzhalter erstellt. Bitte tauschen Sie während des Kopiervorganges für
es mit Hilfe des "Ersetzen" Knopfes ein Ersetzen markiert.
aus.
Die Anwendung "Not applicable" für Sie haben eine Anwendung von
PAHs ist nicht gültig für Werkstoffe PAHs gewählt, die für das
mit einem Gewicht über 1000g. angegebene Gewicht nicht möglich
ist
Nur gültige Anwendungen können für Sie verwenden eine Anwendung, die
Reinstoffe verwendet werden! nicht mehr gültig ist.
Der Werkstoff enthält mehr als {0}% siehe Blatt SC90, Checktyp 2
"{1}", hat aber eine unpassende
Klassifizierung {2}.
Der Werkstoff enthält mehr als {0}% siehe Blatt SC90, Checktyp 2
Reinstoffe der Gruppe "{1}", hat aber
eine unpassende Klassifizierung {2}.
Eine Flüssigkeit oder ein gasförmiger siehe Blatt SC90, Checktyp 3
Reinstoff ist normalerweise nicht in
einem festen Material enthalten.
Für Teile mit einem Gewicht von {1} Die Abweichung ist zu hoch (das
darf die Abweichung {0} nicht erlaubte Maximum hängt vom
überschreiten Gewicht des jeweiligen Teils ab)
Das Modul wurde bereits als obsolet Obsolete Module sollten nicht
markiert referenziert werden
Das Datasheet wurde bereits als Obsolete Datenblätter sollten nicht
obsolet markiert referenzeirt werden
Innerhalb
Korrektur Typ Referenzen
Klicken Sie auf „Korrigieren“, und das System wird Sie FEHLER Nein
zu der Stelle leiten, wo ein Gewicht angegeben werden
muß
Klicken Sie auf „Korrigieren“, und das System wird Sie FEHLER Nein
zu der Stelle leiten, wo die Anzahl angegeben werden
muß
Die Fehlermeldung zeigt an, welcher Knoten das FEHLER Nein
Problem verursacht. Sie müssen die Unterknoten
herausfinden.
Die Fehlermeldung zeigt an, welcher Knoten das FEHLER Nein
Problem verursacht. Sie müssen die Unterknoten
herausfinden.
Die Fehlermeldung zeigt an, welcher Knoten das FEHLER Nein
Problem verursacht. Sie müssen die Unterknoten
herausfinden.
Die Fehlermeldung zeigt an, welcher Knoten das FEHLER Nein
Problem verursacht. Sie müssen die Unterknoten
herausfinden.
Geben Sie die Reinstoffe in Ihrem Werkstoff an. FEHLER Nein
Klicken Sie auf Korrigieren, und das System wird Sie an FEHLER Nein
die Stelle leiten, an der Sie die Prozentzahl hinzufügen
können
Die Fehlermeldung zeigt an, welcher Knoten das FEHLER Nein
Problem verursacht. Sie müssen die Unterknoten
herausfinden.
„Korrigieren“ bringt Sie zu der Stelle im Baum, wo Sie FEHLER Nein
die ID des nicht freigegebenen Datenblattes ersehen
können. Suchen Sie dieses Datenblatt, geben Sie es
frei und gehen Sie zurück zum Original-MDB
Ändern Sie die Beschreibung und geben Sie einen FEHLER, wenn der Nein
sinnvollen Namen ein. Knoten keine Referenz
ist
Klicken Sie auf „Korrigieren“, und das System wird Sie FEHLER Nein
zu der Stelle leiten, wo Sie die Information hinzufügen
können
Ersetzen Sie die weitergeleitete Version mit dem FEHLER Nein
akzeptierten MDB.
Bearbeiten Sie das Halbzeug und geben das FEHLER, wenn das Nein
spezifische Gewicht an. Halbzeug nicht
freigegeben ist
Klicken Sie auf „Korrigieren“, und das System wird Sie WARNUNG Ja
zu der Stelle leiten, wo Sie die Änderung vornehmen (08.05.2008: Vom
können. IMDS Steering
Committee zur
Verfügung gestellte
MDB sind
ausgenommen)
Klicken Sie auf „Korrigieren“, und das System wird Sie FEHLER Ja
zu der Stelle leiten, wo Sie die Änderung vornehmen
können.
Entfernen Sie die Markierung als "vertraulich" FEHLER, falls der Ja
Werkstoff noch nicht
produktiv ist
Wählen Sie entweder "Ja" or "Nein" für die Frage FEHLER Nein
"Enthält der Werkstoff Rezyklat?"
Klicken Sie auf „Korrigieren“, und das System wird Sie FEHLER Ja
zu der Stelle leiten, wo Sie die Änderung vornehmen
können.
Klicken Sie auf „Korrigieren“, und das System wird Sie FEHLER Ja
zu der Stelle leiten, wo Sie die Änderung vornehmen
können.
Ändern Sie den minimalen, bzw. maximalen Rezyklat- FEHLER Nein
Anteil, so dass die Differenz nicht mehr als 20% beträgt.
(WARNUNG ab dem
25.09.2019)
Klicken Sie auf „Korrigieren“, und das System wird Sie FEHLER, wenn das Ja
zu der Stelle leiten, wo Sie die Änderung vornehmen Teil keine Referenz ist,
können. ansonsten WARNUNG
Gehen Sie zu dem Teil, in dem der Werkstoff zuerst FEHLER, wenn das Ja
referenziert ist und beantworten Sie die Frage MDB, das dieses Teil
(eventuell müssen Sie direkt zu einem referenzierten beinhaltet nicht
Teil gehen) freigegeben ist,
ansonsten WARNUNG
Klicken Sie auf „Korrigieren“, und das System wird Sie WARNUNG Ja
zu der Stelle leiten, wo Sie die Änderung vornehmen
können.
FEHLER Ja
FEHLER Ja
Erstellen Sie eine Kopie/neue Version des Werkstoffes, FEHLER, wenn ein Ja
korrigieren Sie den Fehler – eventuell müssen Sie dies eigenes Teil oder
an mehreren Stellen im Baum ändern oder die MDBs OEM-Empfänger,
neu anfordern ansonsten WARNUNG
Erstellen Sie eine Kopie/neue Version des Werkstoffes, FEHLER, wenn ein Ja
korrigieren Sie den Fehler – eventuell müssen Sie dies eigenes Teil oder
an mehreren Stellen im Baum ändern oder die MDBs OEM-Empfänger,
neu anfordern ansonsten WARNUNG
Ersetzen Sie die Referenz durch die neue Version WARNUNG, wenn das Nein
Modul/MDB nicht
freigegeben ist
Einen zweiten Reinstoff hinzufügen WARNUNG (falls kein Ja
Standard-Werkstoff)
Nein
Nein
Nein
Nein
Nein
Nein
Nein
Nein
Nein
Nein
Nein
Nein
Nein
Nein
Nein
Nein
Nein
Nein
Nein
Nein
Nein
Nein
Nein
Nein
Nein
Nein
Nein
Nein
Nein
Ja
Ja
Nein
Nein
Nein
Nein
Ja
Nein
Nein
Nein
Nein
Ja
Nein
Nein
Nein
Ja
Ja
Nein
Nein
Nein
Nein
Nein
Nein
Nein
Nein
Nein
Nein
Nein
Nein
Nein
Nein
Meldung Bedeutung
Ansprechpartner muss bestimmt Der Ansprechpartner wurde nicht
werden ausgewählt und ist undefiniert
Korrektur Typ
Den Ansprechpartner auswählen FEHLER
Für Daten, die für OEMs
bearbeitet wurden
Nein
Meldung Bedeutung
Es muß eine Sach- /Mat.-Nr. Sie haben in ein Pflichtfeld keine
angegeben werden! Informationen eingetragen
Es muß eine Werkstoff-Nr. Sie haben in ein Pflichtfeld keine
angegeben werden! Informationen eingetragen
Es muß eine Teil-/Sach-Nr. Sie haben in ein Pflichtfeld keine
angegeben werden! Informationen eingetragen
Die Firma wurde gelöscht Ihre Empfängerfirma ist nicht mehr
verfügbar
Sie können ein MDB nicht an die Sie versuchen, das MDB an eine
eigene Firma oder eine ihrer Org.- andere Org.-Einheit der gleichen
Einheiten senden/vorschlagen. Firma zu senden
Eine neue Teil-/Sach-Nummer Dies ist ein Verstoß gegen die
erfordert eine neue MDB ID Rec001 Regel 3.2.2.A.
Sie haben eine neue Version eines
bereits gesendeten/vorgeschlagenen
MDBs erstellt, aber eine neue
Teil-/Sach-oder Lieferanten-Nummer
für eine Empfänger-Org.-Einheit
verwendet, die bereits eine frühere
Version des MDBs empfangen hat.
Die Kombination der Teil-/Sach- Dies ist ein Verstoß gegen die
Nummer "{0}" und der Lieferanten- Rec001 Regel 3.2.2.B.
Nummer "{1}" wurde bereits für Die Teil-/Sach- oder Lieferanten-
folgende MDB ID(s) verwendet: {2}. Nummer, die Sie für den Empfänger
verwendet haben, wurde bereits in
einem anderen MDB des selben
Typs mit anderer MDB ID verwendet,
das ebenfalls von Ihrer Org.-Einheit
an diese Empfänger-Org.-Einheit
gesendet/vorgeschlagen wurde.
Tragen Sie bitte wenigstens eine Sie haben für den Werkstoff keine
öffentliche Norm oder eine Toyota Norm/Standard eingegeben. Dieser
Hausnorm ein Werkstoff ist in einem Halbzeug oder
Teil referenziert, das ein Gewicht von
mindestens 5g hat.
Bitte geben Sie den korrekten Index
des Renault-Teils ein.
Die E-Mail-Addresse des Renault-
Designers, der für das Teil zuständig
ist, muß eingegeben werden.
Fügen Sie die Teil-/Sach-Nr. für dieses Teil hinzu FEHLER allgemein
Erstellen Sie eine neue Version der MDB IDs, die WARNUNG allgemein
bereits an die Empfänger gesendet/vorgeschlagen
wurden. In diesem MDB können Sie dann das originale
akzeptiere MDB referenzieren.
Verwenden Sie die "Anwendungs-Änderungen für alle WARNUNG allgemein, nur
OEMs in der Empfängerliste übernehmen"-Funktion, um OEM
Ihre Änderungen für alle OEMs in the Empfängerliste zu
übernehmen
Verwenden Sie die "Änderungen der Kennzeichnungen WARNUNG allgemein, nur
der Polymerwerkstoffe für alle OEMs in der OEM
Empfängerliste übernehmen"-Funktion, um Ihre
Änderungen für alle OEMs in the Empfängerliste zu
übernehmen
FEHLER Renault
FEHLER Renault
FEHLER Renault
FEHLER Renault
FEHLER Renault
Setzen Sie den Haken in Nissans Empfängerdaten FEHLER Nissan
Geben Sie ein Symbol ein oder ersetzen Sie den FEHLER Nissan
Werkstoff
FEHLER Nissan
WARNUNG Nissan
Nein
Nein
Nein
Nein
Nein
Nein
Nein
Ausschließlich
Ausschließlich
Nein
Nein
Nein
Nein
Nein
Nein
Ja
Nein
Nein
Nein
Nein
Nein
Nein
Nein
Nein
No
Nein
Material Substance Check (SC90)
Within the "Material Substance Check (SC90)", there are 3 types of checks:
Common to all checks is, that every material within the ingredients tree will be
checked. If a content check fails, a warning message will be generated.
For the first check, the data in Sheet "SC90_SUBST" applies. According to the
material classification, either there must or there must not be the defined content.
The "must" content can either be a single substance or a group of substances.
These must be contained over a certain percent limit. For the "must not" content, a
substance group and the percent limit is defined.
For the second check, the data in Sheet "SC90_CLASSIF" applies. For several
substances or substance groups, the sum of the percent values are calculated. If
the sums are above the defined limits (usually 50%), the material classification is
checked against the list of suitable classifications.
The third check examines the material for special substance in 3 different
substance groups:
1. Liquids and Gases: If a liquid or gas is contained to more than 1% and the
material is not of classification 9.x, a warning message will be generated. An
exception for this rule is water (7732-18-5), which can be contained without limit
in a material of classification 7.1.
2. Reactive Substances: If a reactive substance is contained to more than 1%, a
warning message will be generated.
3. Ions: If ions are contained to more than 1%, a warning message will be
generated.
Materials supplied by the IMDS Steering Committee will be excluded from any check.
Semicomponents published by ZVEI-Rec019 (CompanyId 102677) will also be
excluded from any check.
To calculate the percent value of a substance, a worst case scenario is used. This
means either the fix or rest value, or the minimum or maximum of a range. The
minimum value is used for the "must contain" check. For all other checks the
maximum value is used. For a substance group, the sum of all substances within
the material which belong to the group is calculated.
Classification Classification name Must contain
1 Steel and iron materials
1.1 Steels / cast steel / sintered steel Fe ≥ 50%
1.1.1 unalloyed, low alloyed Fe ≥ 65%
1.1.2 highly alloyed Fe ≥ 30%
1.2 Cast iron Fe ≥ 50%
Cast iron with lamellar graphite /
1.2.1 tempered cast iron Fe ≥ 70%
Cast iron with nodular graphite /
1.2.2 vermicular cast iron Fe ≥ 55%
1.2.3 Highly alloyed cast iron Fe ≥ 14%
2.1 Aluminum and aluminum alloys Al ≥ 50%
2.1.1 Cast aluminum alloys Al ≥ 50%
2.1.2 Wrought aluminum alloys Al ≥ 50%
Mg or Magnesium powder
(stabilized) or a sum of
2.2 Magnesium and magnesium alloys both ≥ 50%
Mg or Magnesium powder
(stabilized) or a sum of
2.2.1 Cast magnesium alloys both ≥ 50%
Mg or Magnesium powder
(stabilized) or a sum of
2.2.2 Wrought magnesium alloys both ≥ 50%
2.3 Titanium and titanium alloys Ti ≥ 50%
Heavy metals, cast and wrought
3 alloys
Copper (e.g. copper amounts in
3.1 cable harnesses) Cu ≥ 93%
3.2 Copper alloys Cu ≥ 48%
Sum of Zinc substances ≥
3.3 Zinc alloys 70%
3.4 Nickel alloys Ni ≥ 50%
3.5 Lead Pb ≥ 50%
4 Special metals
Sum of Platinum and
4.1 Platinum / rhodium Rhodium ≥ 50%
Other metals or their sum
4.2 Other special metals ≥ 50 %
5 Polymer materials
5.1 Thermoplastics
Sum of substances
containing …poly… in their
names excluding sum of
5.1.a filled Thermoplastics Basic Duromers ≥ 23%
Sum of substances
containing …poly…in their
names excluding sum of
5.1.b unfilled Thermoplastics Basic Duromers ≥ 25%
Sum of substances
containing …poly…in their
names excluding sum of
5.2 Thermoplastic elastomers Basic Duromers ≥ 25%
Sum of Basic Rubbers or
substances containing …
poly… in their names
excluding Basic Polymers
and Basic Duromers and ≥
5.3 Elastomers / elastomeric compounds 10%
Sum of substances
containing …poly… in their
names excluding sum of
5.4 Duromers Basic Polymers ≥ 15%
Sum of substances
containing …poly… in their
5.4.1 Polyurethane names ≥ 25%
Sum of substances
containing …poly… in their
names excluding sum of
5.4.2 Unsaturated polyester Basic Polymers ≥ 15%
Sum of substances
containing …poly… in their
names excluding sum of
5.4.3 Other duromers Basic Polymers ≥ 15%
Polymeric compounds (e.g.
5.5 inseparable laminated trim parts)
Sum of substances
containing …poly… in their
5.5.1 Plastics (in polymeric compounds) names ≥ 25%
6.3 Underseal -
Other materials and material
7 compounds (scope of mixture)
9.1 Fuels -
9.2 Lubricants -
9.5 Refrigerant -
9.7 Preservative -
7439-89-6 -
7439-89-6 -
7439-89-6 -
7439-89-6 -
7439-89-6 -
7439-89-6 -
7439-89-6 -
7429-90-5 -
7429-90-5 -
7429-90-5 -
Chk: Magnesium -
Chk: Magnesium -
Chk: Magnesium -
7440-32-6 -
7440-50-8 -
7440-50-8 -
Chk: Zinc -
7440-02-0 -
7439-92-1 -
Special metals -
5.x, 6.x, 7.2, 7.3, 8.x, 9.2, 9.3, 9.4, 9.7, 9.8