Professional Documents
Culture Documents
DESIGN CALCULATION
FOR
PROJECT
RPEPL-BCW-ME-
Doc.No: - Rev
CLIENT
EPC
RAYS POWER EXPERT PVT.LTD, JAIPUR
RPEPL-BCW-ME-
Doc.No: - Rev
0 30/09/20 FOR
M.A M.A M.A
APPROVAL
REV INTLS SGN INTLS SGN INTLS SGN
DATE STATUS
NO PRPD. BY CHKD. BY APPR. BY
CONTENTS
1. GENERAL............................................................................................................................... 5
1.1. SCOPE........................................................................................................................................ 5
RPEPL-BCW-ME-
Doc.No: - Rev
4. DESIGN OF RC ELEMENTS................................................................................................11
4.1 3D VIEW..................................................................................................................................... 11
CONCRETE DESIGN
ANNEXURE -A (Foundation Design)
RPEPL-BCW-ME-
Doc.No: - Rev
1. GENERAL
1.1. SCOPE
This document covers the Analysis and Design of MCR building for Development of4.1 MW
proposed Solar Power project at Medinipur,W.B.The objective of this document is to design
the Foundations, Columns, Beams and Slab of MCR building.
RPEPL-BCW-ME-
Doc.No: - Rev
Density 25 kN/cum
N/sq
Concrete, Characteristic Strength 25
mm
M25
N/sq
Modulus of Elasticity 25000
mm
Specification IS 13920
High Strength Density 78.5 kN/cum
Reinforcing
N/sq.m
Steel Characteristic Strength 415
m
(TMT)
N/sq.m
Modulus of Elasticity 200000
m
Specification IS 1786
Basic wind speed : 50 m/s (180 km/h). (As per IS 875-Part 3 - 2015)
1.6. SOFTWARE REFERENCE
STAAD - Pro, Research Engineers Inc., Berkely, USA
In-house developed Ms-Excel Sheets.
The above software packages are used for the structural analysis and the same are carried
out in this document.
The MCR building is a Single Story RCC framed structure of length 5.0 m, breadth 5.0 m (both
from center to center of columns) and height 3.5 m (from Finished Floor Level to the top of
roof slab).
3. DESIGN PHILOSOPHY
The MCR building is designed using the structural analysis software package STAAD.Pro V8i
and in-house MS-Excel Sheets. The analysis is performed for self-weight of structural
members, other Dead Load on the members, Live Load & Seismic Loads. Various possible
load combinations of the above loads are listed in section 4.3 in accordance with IS-456:2000.
RPEPL-BCW-ME-
Doc.No: - Rev
LIVE LOAD
Live Load = 1.5 kN/m2
WIND LOAD
Wind Load on structure is calculated as per IS: 875 (Part-III)-2015. The Wind load have been
defined in STAAD for intensity of 1.075 KN/sqm.
RPEPL-BCW-ME-
Doc.No: - Rev
RPEPL-BCW-ME-
Doc.No: - Rev
4. DESIGN OF RC ELEMENTS
4.1 3D VIEW
RPEPL-BCW-ME-
Doc.No: - Rev
DEAD LOAD
LIVE LOAD
RPEPL-BCW-ME-
Doc.No: - Rev
RPEPL-BCW-ME-
Doc.No: - Rev
RPEPL-BCW-ME-
Doc.No: - Rev
using the suitable command following the relevant clauses of IS: 456 – 2000.
RPEPL-BCW-ME-
Doc.No: - Rev
56. TYPE 1 WX
57. INT 1 1.5 HEIG 10 20
58. UNIT MMS KN
59. LOAD 1 LOADTYPE DEAD TITLE DL
60. MEMBER LOAD
61. 37 TO 42 44 48 TO 50 52 UNI GY -0.01413
62. 34 TO 36 43 45 TO 47 51 UNI GY -0.007005
63. SELFWEIGHT Y -2.15
64. MEMBER LOAD
65. 70 TO 75 77 81 TO 83 85 UNI GY -0.002622
66. FLOOR LOAD
67. YRANGE 0 10000 FLOAD -3.75E-006 GY
68. UNIT METER KN
69. YRANGE 0 10 FLOAD -3.75 GY
70. UNIT MMS KN
71. LOAD 2 LOADTYPE LIVE REDUCIBLE TITLE LL
72. MEMBER LOAD
73. 20 TO 23 26 28 TO 31 33 TO 56 59 61 TO 64 66 TO 85 UNI GY -0.0015
74. UNIT METER KN
75. LOAD 3 LOADTYPE WIND TITLE WX
76. WIND LOAD X 1 TYPE 1 YR 0 10
77. WIND LOAD X -1 TYPE 1 YR 0 10
DXF IMPORT OF FIRST 123.DXF -- PAGE NO. 3
78. LOAD 4 LOADTYPE WIND TITLE WZ
79. WIND LOAD Z 1 TYPE 1 YR 0 10
80. WIND LOAD Z -1 TYPE 1 YR 0 10
81. LOAD COMB 5 GENERATED INDIAN CODE GENRAL_STRUCTURES 1 82. 1 1.5 2 1.5
83. LOAD COMB 6 GENERATED INDIAN CODE GENRAL_STRUCTURES 2 84. 1 1.2 2 1.2 3 1.2
85. LOAD COMB 7 GENERATED INDIAN CODE GENRAL_STRUCTURES 3 86. 1 1.2 2 1.2 4 1.2
87. LOAD COMB 8 GENERATED INDIAN CODE GENRAL_STRUCTURES 4 88. 1 1.2 2 1.2 3 -1.2
89. LOAD COMB 9 GENERATED INDIAN CODE GENRAL_STRUCTURES 5 90. 1 1.2 2 1.2 4 -1.2
91. LOAD COMB 10 GENERATED INDIAN CODE GENRAL_STRUCTURES 6 92. 1 1.2 2 1.2
93. LOAD COMB 11 GENERATED INDIAN CODE GENRAL_STRUCTURES 7 94. 1 1.5 3 1.5
95. LOAD COMB 12 GENERATED INDIAN CODE GENRAL_STRUCTURES 8 96. 1 1.5 4 1.5
97. LOAD COMB 13 GENERATED INDIAN CODE GENRAL_STRUCTURES 9 98. 1 1.5 3 -1.5
99. LOAD COMB 14 GENERATED INDIAN CODE GENRAL_STRUCTURES 10 100. 1 1.5 4 -1.5
101. LOAD COMB 15 GENERATED INDIAN CODE GENRAL_STRUCTURES 11 102. 1 1.5
103. LOAD COMB 16 GENERATED INDIAN CODE GENRAL_STRUCTURES 12 104. 1 0.9
!> END GENERATED DATA BLOCK
FLOOR LOAD
YRANGE 3.5 4 FLOAD -2.15 GY
LOAD 4 LOADTYPE Live REDUCIBLE TITLE IMPOSED LOAD
FLOOR LOAD
YRANGE 3.5 4 FLOAD -1.5 GY
LOAD 6 LOADTYPE Wind TITLE WX- DIR
WIND LOAD X -1 TYPE 1 YR -1.2 4.75
LOAD 7 LOADTYPE Wind TITLE WZ+ DIR
WIND LOAD Z 1 TYPE 1 YR -1.2 6.75
LOAD 8 LOADTYPE Wind TITLE WZ- DIR
WIND LOAD Z -1 TYPE 1 YR -1.2 4.75
LOAD 5 LOADTYPE Wind TITLE WX
WIND LOAD X 1 TYPE 1 YR -1.2 4.75
******************************************
* * * Limit State of serviceability
******************************************
LOAD COMB 101 1*DL+1*LL
3 1.0 4 1.0
RPEPL-BCW-ME-
Doc.No: - Rev
RPEPL-BCW-ME-
Doc.No: - Rev
RPEPL-BCW-ME-
Doc.No: - Rev
- Bottom Reinforcement(Mz) Bottom Reinforcement(Mx) Top Reinforcement(Mz) Top Reinforcement(Mx) Main Steel Trans Steel
1 Ø16 @ 85 mm c/c Ø16 @ 85 mm c/c Ø10 @ 55 mm c/c Ø10 @ 55 mm c/c N/A N/A
2 Ø16 @ 80 mm c/c Ø16 @ 80 mm c/c Ø10 @ 50 mm c/c Ø10 @ 50 mm c/c N/A N/A
3 Ø12 @ 50 mm c/c Ø12 @ 50 mm c/c Ø10 @ 60 mm c/c Ø10 @ 60 mm c/c N/A N/A
4 Ø16 @ 85 mm c/c Ø16 @ 85 mm c/c Ø10 @ 55 mm c/c Ø10 @ 55 mm c/c N/A N/A
7 Ø12 @ 50 mm c/c Ø12 @ 50 mm c/c Ø10 @ 60 mm c/c Ø10 @ 65 mm c/c N/A N/A
9 Ø16 @ 75 mm c/c Ø16 @ 75 mm c/c Ø10 @ 50 mm c/c Ø10 @ 50 mm c/c N/A N/A
10 Ø12 @ 60 mm c/c Ø12 @ 65 mm c/c Ø10 @ 75 mm c/c Ø8 @ 50 mm c/c N/A N/A
11 Ø12 @ 65 mm c/c Ø12 @ 65 mm c/c Ø8 @ 50 mm c/c Ø8 @ 50 mm c/c N/A N/A
12 Ø16 @ 75 mm c/c Ø16 @ 75 mm c/c Ø10 @ 50 mm c/c Ø10 @ 50 mm c/c N/A N/A
16 Ø12 @ 50 mm c/c Ø12 @ 50 mm c/c Ø10 @ 60 mm c/c Ø10 @ 60 mm c/c N/A N/A
Design For Isolated Footing 16
Isolated Footing 1
RPEPL-BCW-ME-
Doc.No: - Rev
Input Values
Footing Geomtery
Design Type : Calculate Dimension
Footing Thickness (Ft) : 305.000 mm
Footing Length - X (Fl) : 1000.000 mm
Footing Width - Z (Fw) : 1000.000 mm
Eccentricity along X (Oxd) : 0.000 mm
Eccentricity along Z (Ozd) : 0.000 mm
Column Dimensions
Column Shape : Rectangular
Column Length - X (Pl) : 0.300 m
Column Width - Z (Pw) : 0.300 m
RPEPL-BCW-ME-
Doc.No: - Rev
Pedestal
Include Pedestal? No
Pedestal Shape : N/A
Pedestal Height (Ph) : N/A
Pedestal Length - X (Pl) : N/A
Pedestal Width - Z (Pw) : N/A
Design Parameters
Concrete and Rebar Properties
Unit Weight of Concrete : 25.000 kN/m3
Strength of Concrete : 25.000 N/mm2
Yield Strength of Steel : 415.000 N/mm2
Minimum Bar Size : Ø6
Maximum Bar Size : Ø32
Minimum Bar Spacing : 50.000 mm
Maximum Bar Spacing : 500.000 mm
Pedestal Clear Cover (P, CL) : 50.000 mm
Footing Clear Cover (F, CL) : 50.000 mm
Soil Properties
Soil Type : Drained
Unit Weight : 22.000 kN/m3
Soil Bearing Capacity : 100.000 kN/m2
Soil Surcharge : 0.000 kN/m2
Depth of Soil above Footing : 0.000 mm
Cohesion : 0.000 kN/m2
Min Percentage of Slab : 0.000
Sliding and Overturning
------------------------------------------------------
Load Combination
Load Combination Title
Number
1 DL
2 LL
3 WX
4 WZ
5 Generated Indian Code Genral_Structures 1
RPEPL-BCW-ME-
Doc.No: - Rev
RPEPL-BCW-ME-
Doc.No: - Rev
Design Calculations
Footing Size
RPEPL-BCW-ME-
Doc.No: - Rev
Area from initial length and width, A o = Lo X Wo = 1.000 m2 Min. area required from
------------------------------------------------------
Area of
Pressure at Pressure at Pressure at Pressure at footing in
Load Case corner 1 (q1) corner 2 (q2) corner 3 (q3) corner 4 (q4) uplift (Au)
(kN/m2) (kN/m2) (kN/m2) (kN/m2)
(m2)
RPEPL-BCW-ME-
Doc.No: - Rev
------------------------------------------------------
Check For Stability Against Overturning And Sliding
- Factor of safety against sliding Factor of safety against overturning
RPEPL-BCW-ME-
Doc.No: - Rev
------------------------------------------------------
Moment Calculation
Check Trial Depth against moment (w.r.t. X Axis)
ANNEX G G-1.1C
)=
Limit Moment Of Resistance (Mumax
RPEPL-BCW-ME-
Doc.No: - Rev
= 31938.902382 kNm
ANNEX G G-1.1C
)=
Limit Moment Of Resistance (Mumax
= 31938.902382 kNm
------------------------------------------------------
Shear Calculation
Check Trial Depth for one way shear (Along X Axis)
(Shear Plane Parallel to X Axis)
DX = 1.057 m
RPEPL-BCW-ME-
Doc.No: - Rev
Check Trial Depth for one way shear (Along Z Axis) (Shear Plane Parallel to Z
Axis)
DZ = 1.057 m
Shear Force(S) = 2531.548 kN
RPEPL-BCW-ME-
Doc.No: - Rev
Ks = = 1.000
Ks x Tc = 1250.0000 kN/m2
------------------------------------------------------
Reinforcement Calculation
Calculation of Maximum Bar Size
Along X Axis
Development Length(ld) =
= 1.289 m
Allowable Length(ldb) =
= 3.950 m
RPEPL-BCW-ME-
Doc.No: - Rev
Along Z Axis
Along Z Axis
RPEPL-BCW-ME-
Doc.No: - Rev
Smin <= S <= Smax and selected bar size < selected maximum bar size...
Along X Axis
RPEPL-BCW-ME-
Doc.No: - Rev
Smin <= S <= Smax and selected bar size < selected maximum bar size...
Along Z Axis
2047.296 kNm
Smin <= S <= Smax and selected bar size < selected maximum bar size... The reinforcement is
accepted.
RPEPL-BCW-ME-
Doc.No: - Rev
Ø10 @ 55 mm o.c.
Along X Axis
2047.296 kNm
Smin <= S <= Smax and selected bar size < selected maximum bar size... The reinforcement is
accepted.
Ø10 @ 55 mm o.c.
------------------------------------------------------
RPEPL-BCW-ME-
Doc.No: - Rev
Isolated Footing 2
Input Values
Footing Geomtery
Design Type : Calculate Dimension
Footing Thickness (Ft) : 305.000 mm
Footing Length - X (Fl) : 1000.000 mm
Footing Width - Z (Fw) : 1000.000 mm Eccentricity along X (Oxd) : 0.000
mm
Eccentricity along Z (Ozd) : 0.000 mm
RPEPL-BCW-ME-
Doc.No: - Rev
Column Dimensions
Column Shape : Rectangular
Column Length - X (Pl) : 0.300 m
Column Width - Z (Pw) : 0.300 m
Pedestal
Include Pedestal? No
Pedestal Shape : N/A
Pedestal Height (Ph) : N/A
Pedestal Length - X (Pl) : N/A
Pedestal Width - Z (Pw) : N/A
Design Parameters
Concrete and Rebar Properties
Unit Weight of Concrete : 25.000 kN/m3
Strength of Concrete : 25.000 N/mm2
Yield Strength of Steel : 415.000 N/mm2
Minimum Bar Size : Ø6
Maximum Bar Size : Ø32
Minimum Bar Spacing : 50.000 mm
Maximum Bar Spacing : 500.000 mm
Pedestal Clear Cover (P, CL) : 50.000 mm
Footing Clear Cover (F, CL) : 50.000 mm
Soil Properties
Soil Type : Drained
Unit Weight : 22.000 kN/m3
Soil Bearing Capacity : 100.000 kN/m2
Soil Surcharge : 0.000 kN/m2
Depth of Soil above Footing : 0.000 mm
Cohesion : 0.000 kN/m2
Min Percentage of Slab : 0.000
Sliding and Overturning
------------------------------------------------------
RPEPL-BCW-ME-
Doc.No: - Rev
Number
1 DL
2 LL
3 WX
4 WZ
RPEPL-BCW-ME-
Doc.No: - Rev
RPEPL-BCW-ME-
Doc.No: - Rev
Design Calculations
Footing Size
Area from initial length and width, A o = Lo X Wo = 1.000 m2 Min. area required from
------------------------------------------------------
Area of
Pressure at Pressure at Pressure at Pressure at footing in
Load Case corner 1 (q1) corner 2 (q2) corner 3 (q3) corner 4 (q4) uplift (Au)
(kN/m2) (kN/m2) (kN/m2) (kN/m2)
RPEPL-BCW-ME-
Doc.No: - Rev
(m2)
101 94.0016 95.6531 98.8619 97.2104 0.000
101 94.0016 95.6531 98.8619 97.2104 0.000
101 93.1672 95.4849 99.7328 97.4151 0.000
101 93.1672 95.4849 99.7328 97.4151 0.000
If Au is zero, there is no uplift and no pressure adjustment is necessary. Otherwise, to account for uplift, areas of negative pressure
will be set to zero and the pressure will be redistributed to remaining corners.
Summary of adjusted Pressures at Four Corner
Pressure at Pressure at Pressure at Pressure at
corner 1 (q1) corner 2 (q2) corner 3 (q3) corner 4 (q4)
Load Case
------------------------------------------------------
Check For Stability Against Overturning And Sliding
- Factor of safety against sliding Factor of safety against overturning
RPEPL-BCW-ME-
Doc.No: - Rev
------------------------------------------------------
Moment Calculation
Check Trial Depth against moment (w.r.t. X Axis)
ANNEX G G-1.1C
RPEPL-BCW-ME-
Doc.No: - Rev
)=
PROJECT: DEVELOPMENT OF 4.1MW SOLAR 4.1MW-ED-CRA-F11-01 00
PV PLANT, MEDINIPUR,W.B
Date: 12/10/2021 Page 39 of 159
DESIGN CALCULATION FOR MCR
BUILDING FOR 4.1 MW AT
MEDINIPUR,W.B.
ANNEX G G-1.1C
)=
Limit Moment Of Resistance (Mumax
= 42187.105729 kNm
------------------------------------------------------
Shear Calculation
Check Trial Depth for one way shear (Along X Axis)
(Shear Plane Parallel to X Axis)
DX = 1.157 m
RPEPL-BCW-ME-
Doc.No: - Rev
Check Trial Depth for one way shear (Along Z Axis) (Shear Plane Parallel to Z
Axis)
DZ = 1.157 m
Shear Force(S) = 3002.702 kN
RPEPL-BCW-ME-
Doc.No: - Rev
Ks = = 1.000
Ks x Tc = 1250.0000 kN/m2
------------------------------------------------------
Reinforcement Calculation
Calculation of Maximum Bar Size
Along X Axis
Development Length(ld) =
= 1.289 m
Allowable Length(ldb) =
= 4.375 m
RPEPL-BCW-ME-
Doc.No: - Rev
Along Z Axis
Along Z Axis
RPEPL-BCW-ME-
Doc.No: - Rev
Smin <= S <= Smax and selected bar size < selected maximum bar size...
Along X Axis
RPEPL-BCW-ME-
Doc.No: - Rev
Smin <= S <= Smax and selected bar size < selected maximum bar size...
Along Z Axis
3010.874 kNm
Smin <= S <= Smax and selected bar size < selected maximum bar size... The reinforcement is
accepted.
RPEPL-BCW-ME-
Doc.No: - Rev
Ø10 @ 50 mm o.c.
Along X Axis
3010.874 kNm
Smin <= S <= Smax and selected bar size < selected maximum bar size... The reinforcement is
accepted.
Ø10 @ 50 mm o.c.
------------------------------------------------------
RPEPL-BCW-ME-
Doc.No: - Rev
Isolated Footing 3
Input Values
Footing Geomtery
Design Type : Calculate Dimension
Footing Thickness (Ft) : 305.000 mm
Footing Length - X (Fl) : 1000.000 mm
Footing Width - Z (Fw) : 1000.000 mm Eccentricity along X (Oxd) : 0.000
mm
Eccentricity along Z (Ozd) : 0.000 mm
RPEPL-BCW-ME-
Doc.No: - Rev
Column Dimensions
Column Shape : Rectangular
Column Length - X (Pl) : 0.300 m
Column Width - Z (Pw) : 0.300 m
Pedestal
Include Pedestal? No
Pedestal Shape : N/A
Pedestal Height (Ph) : N/A
Pedestal Length - X (Pl) : N/A
Pedestal Width - Z (Pw) : N/A
Design Parameters
Concrete and Rebar Properties
Unit Weight of Concrete : 25.000 kN/m3
Strength of Concrete : 25.000 N/mm2
Yield Strength of Steel : 415.000 N/mm2
Minimum Bar Size : Ø6
Maximum Bar Size : Ø32
Minimum Bar Spacing : 50.000 mm
Maximum Bar Spacing : 500.000 mm
Pedestal Clear Cover (P, CL) : 50.000 mm
Footing Clear Cover (F, CL) : 50.000 mm
Soil Properties
Soil Type : Drained
Unit Weight : 22.000 kN/m3
Soil Bearing Capacity : 100.000 kN/m2
Soil Surcharge : 0.000 kN/m2
Depth of Soil above Footing : 0.000 mm
Cohesion : 0.000 kN/m2
Min Percentage of Slab : 0.000
Sliding and Overturning
------------------------------------------------------
RPEPL-BCW-ME-
Doc.No: - Rev
Number
1 DL
2 LL
3 WX
4 WZ
RPEPL-BCW-ME-
Doc.No: - Rev
RPEPL-BCW-ME-
Doc.No: - Rev
Design Calculations
Footing Size
Area from initial length and width, A o = Lo X Wo = 1.000 m2 Min. area required from
------------------------------------------------------
Area of
Pressure at Pressure at Pressure at Pressure at footing in
Load Case corner 1 (q1) corner 2 (q2) corner 3 (q3) corner 4 (q4) uplift (Au)
(kN/m2) (kN/m2) (kN/m2) (kN/m2)
RPEPL-BCW-ME-
Doc.No: - Rev
(m2)
101 95.5821 95.8248 98.7819 98.5393 0.000
101 95.5491 95.8946 99.7760 99.4305 0.000
101 95.5491 95.8946 99.7760 99.4305 0.000
101 95.5491 95.8946 99.7760 99.4305 0.000
If Au is zero, there is no uplift and no pressure adjustment is necessary. Otherwise, to account for uplift, areas of negative pressure
will be set to zero and the pressure will be redistributed to remaining corners.
Summary of adjusted Pressures at Four Corner
Pressure at Pressure at Pressure at Pressure at
corner 1 (q1) corner 2 (q2) corner 3 (q3) corner 4 (q4)
Load Case
------------------------------------------------------
Check For Stability Against Overturning And Sliding
- Factor of safety against sliding Factor of safety against overturning
RPEPL-BCW-ME-
Doc.No: - Rev
------------------------------------------------------
Moment Calculation
Check Trial Depth against moment (w.r.t. X Axis)
ANNEX G G-1.1C
RPEPL-BCW-ME-
Doc.No: - Rev
)=
PROJECT: DEVELOPMENT OF 4.1MW SOLAR 4.1MW-ED-CRA-F11-01 00
PV PLANT, MEDINIPUR,W.B
Date: 12/10/2021 Page 53 of 159
DESIGN CALCULATION FOR MCR
BUILDING FOR 4.1 MW AT
MEDINIPUR,W.B.
ANNEX G G-1.1C
)=
Limit Moment Of Resistance (Mumax
= 27308.239555 kNm
------------------------------------------------------
Shear Calculation
Check Trial Depth for one way shear (Along X Axis)
(Shear Plane Parallel to X Axis)
DX = 1.005 m
RPEPL-BCW-ME-
Doc.No: - Rev
Check Trial Depth for one way shear (Along Z Axis) (Shear Plane Parallel to Z
Axis)
DZ = 1.005 m
Shear Force(S) = 2326.369 kN
RPEPL-BCW-ME-
Doc.No: - Rev
Ks = = 1.000
Ks x Tc = 1250.0000 kN/m2
------------------------------------------------------
Reinforcement Calculation
Calculation of Maximum Bar Size
Along X Axis
Development Length(ld) =
= 1.289 m
Allowable Length(ldb) =
= 3.725 m
RPEPL-BCW-ME-
Doc.No: - Rev
Along Z Axis
Along Z Axis
RPEPL-BCW-ME-
Doc.No: - Rev
Smin <= S <= Smax and selected bar size < selected maximum bar size...
Along X Axis
RPEPL-BCW-ME-
Doc.No: - Rev
Smin <= S <= Smax and selected bar size < selected maximum bar size...
Along Z Axis
1643.800 kNm
Smin <= S <= Smax and selected bar size < selected maximum bar size... The reinforcement is
accepted.
RPEPL-BCW-ME-
Doc.No: - Rev
Ø10 @ 60 mm o.c.
Along X Axis
1643.800 kNm
Smin <= S <= Smax and selected bar size < selected maximum bar size... The reinforcement is
accepted.
Ø10 @ 60 mm o.c.
------------------------------------------------------
RPEPL-BCW-ME-
Doc.No: - Rev
Isolated Footing 4
Input Values
Footing Geomtery
Design Type : Calculate Dimension
Footing Thickness (Ft) : 305.000 mm
Footing Length - X (Fl) : 1000.000 mm
Footing Width - Z (Fw) : 1000.000 mm Eccentricity along X (Oxd) : 0.000
mm
Eccentricity along Z (Ozd) : 0.000 mm
RPEPL-BCW-ME-
Doc.No: - Rev
Column Dimensions
Column Shape : Rectangular
Column Length - X (Pl) : 0.300 m
Column Width - Z (Pw) : 0.300 m
Pedestal
Include Pedestal? No
Pedestal Shape : N/A
Pedestal Height (Ph) : N/A
Pedestal Length - X (Pl) : N/A
Pedestal Width - Z (Pw) : N/A
Design Parameters
Concrete and Rebar Properties
Unit Weight of Concrete : 25.000 kN/m3
Strength of Concrete : 25.000 N/mm2
Yield Strength of Steel : 415.000 N/mm2
Minimum Bar Size : Ø6
Maximum Bar Size : Ø32
Minimum Bar Spacing : 50.000 mm
Maximum Bar Spacing : 500.000 mm
Pedestal Clear Cover (P, CL) : 50.000 mm
Footing Clear Cover (F, CL) : 50.000 mm
Soil Properties
Soil Type : Drained
Unit Weight : 22.000 kN/m3
Soil Bearing Capacity : 100.000 kN/m2
Soil Surcharge : 0.000 kN/m2
Depth of Soil above Footing : 0.000 mm
Cohesion : 0.000 kN/m2
Min Percentage of Slab : 0.000
Sliding and Overturning
------------------------------------------------------
RPEPL-BCW-ME-
Doc.No: - Rev
Number
1 DL
2 LL
3 WX
4 WZ
RPEPL-BCW-ME-
Doc.No: - Rev
RPEPL-BCW-ME-
Doc.No: - Rev
Design Calculations
Footing Size
Area from initial length and width, A o = Lo X Wo = 1.000 m2 Min. area required from
------------------------------------------------------
Area of
Pressure at Pressure at Pressure at Pressure at footing in
Load Case corner 1 (q1) corner 2 (q2) corner 3 (q3) corner 4 (q4) uplift (Au)
(kN/m2) (kN/m2) (kN/m2) (kN/m2)
RPEPL-BCW-ME-
Doc.No: - Rev
(m2)
101 99.3463 99.5112 97.9797 97.8148 0.000
101 99.3463 99.5112 97.9797 97.8148 0.000
101 99.3463 99.5112 97.9797 97.8148 0.000
101 99.3463 99.5112 97.9797 97.8148 0.000
If Au is zero, there is no uplift and no pressure adjustment is necessary. Otherwise, to account for uplift, areas of negative pressure
will be set to zero and the pressure will be redistributed to remaining corners.
Summary of adjusted Pressures at Four Corner
Pressure at Pressure at Pressure at Pressure at
corner 1 (q1) corner 2 (q2) corner 3 (q3) corner 4 (q4)
Load Case
------------------------------------------------------
Check For Stability Against Overturning And Sliding
- Factor of safety against sliding Factor of safety against overturning
RPEPL-BCW-ME-
Doc.No: - Rev
------------------------------------------------------
Moment Calculation
Check Trial Depth against moment (w.r.t. X Axis)
ANNEX G G-1.1C
RPEPL-BCW-ME-
Doc.No: - Rev
)=
PROJECT: DEVELOPMENT OF 4.1MW SOLAR 4.1MW-ED-CRA-F11-01 00
PV PLANT, MEDINIPUR,W.B
Date: 12/10/2021 Page 67 of 159
DESIGN CALCULATION FOR MCR
BUILDING FOR 4.1 MW AT
MEDINIPUR,W.B.
ANNEX G G-1.1C
)=
Limit Moment Of Resistance (Mumax
= 31434.799513 kNm
------------------------------------------------------
Shear Calculation
Check Trial Depth for one way shear (Along X Axis)
(Shear Plane Parallel to X Axis)
DX = 1.055 m
RPEPL-BCW-ME-
Doc.No: - Rev
Check Trial Depth for one way shear (Along Z Axis) (Shear Plane Parallel to Z
Axis)
DZ = 1.055 m
Shear Force(S) = 2502.014 kN
RPEPL-BCW-ME-
Doc.No: - Rev
Ks = = 1.000
Ks x Tc = 1250.0000 kN/m2
------------------------------------------------------
Reinforcement Calculation
Calculation of Maximum Bar Size
Along X Axis
Development Length(ld) =
= 1.289 m
Allowable Length(ldb) =
= 3.900 m
RPEPL-BCW-ME-
Doc.No: - Rev
Along Z Axis
Along Z Axis
RPEPL-BCW-ME-
Doc.No: - Rev
Smin <= S <= Smax and selected bar size < selected maximum bar size...
Along X Axis
RPEPL-BCW-ME-
Doc.No: - Rev
Smin <= S <= Smax and selected bar size < selected maximum bar size...
Along Z Axis
1968.826 kNm
Smin <= S <= Smax and selected bar size < selected maximum bar size... The reinforcement is
accepted.
RPEPL-BCW-ME-
Doc.No: - Rev
Ø10 @ 55 mm o.c.
Along X Axis
1968.826 kNm
Smin <= S <= Smax and selected bar size < selected maximum bar size... The reinforcement is
accepted.
Ø10 @ 55 mm o.c.
------------------------------------------------------
RPEPL-BCW-ME-
Doc.No: - Rev
Isolated Footing 7
Input Values
Footing Geomtery
Design Type : Calculate Dimension
Footing Thickness (Ft) : 305.000 mm
Footing Length - X (Fl) : 1000.000 mm
Footing Width - Z (Fw) : 1000.000 mm Eccentricity along X (Oxd) : 0.000
mm
Eccentricity along Z (Ozd) : 0.000 mm
RPEPL-BCW-ME-
Doc.No: - Rev
Column Dimensions
Column Shape : Rectangular
Column Length - X (Pl) : 0.300 m
Column Width - Z (Pw) : 0.300 m
Pedestal
Include Pedestal? No
Pedestal Shape : N/A
Pedestal Height (Ph) : N/A
Pedestal Length - X (Pl) : N/A
Pedestal Width - Z (Pw) : N/A
Design Parameters
Concrete and Rebar Properties
Unit Weight of Concrete : 25.000 kN/m3
Strength of Concrete : 25.000 N/mm2
Yield Strength of Steel : 415.000 N/mm2
Minimum Bar Size : Ø6
Maximum Bar Size : Ø32
Minimum Bar Spacing : 50.000 mm
Maximum Bar Spacing : 500.000 mm
Pedestal Clear Cover (P, CL) : 50.000 mm
Footing Clear Cover (F, CL) : 50.000 mm
Soil Properties
Soil Type : Drained
Unit Weight : 22.000 kN/m3
Soil Bearing Capacity : 100.000 kN/m2
Soil Surcharge : 0.000 kN/m2
Depth of Soil above Footing : 0.000 mm
Cohesion : 0.000 kN/m2
Min Percentage of Slab : 0.000
Sliding and Overturning
------------------------------------------------------
RPEPL-BCW-ME-
Doc.No: - Rev
Number
1 DL
2 LL
3 WX
4 WZ
RPEPL-BCW-ME-
Doc.No: - Rev
RPEPL-BCW-ME-
Doc.No: - Rev
Design Calculations
Footing Size
Area from initial length and width, A o = Lo X Wo = 1.000 m2 Min. area required from
------------------------------------------------------
Area of
Pressure at Pressure at Pressure at Pressure at footing in
Load Case corner 1 (q1) corner 2 (q2) corner 3 (q3) corner 4 (q4) uplift (Au)
(kN/m2) (kN/m2) (kN/m2) (kN/m2)
RPEPL-BCW-ME-
Doc.No: - Rev
(m2)
101 95.0021 98.7958 87.1615 83.3678 0.000
101 94.5977 99.4661 84.3011 79.4326 0.000
101 95.0021 98.7958 87.1615 83.3678 0.000
101 95.0021 98.7958 87.1615 83.3678 0.000
If Au is zero, there is no uplift and no pressure adjustment is necessary. Otherwise, to account for uplift, areas of negative pressure
will be set to zero and the pressure will be redistributed to remaining corners.
Summary of adjusted Pressures at Four Corner
Pressure at Pressure at Pressure at Pressure at
corner 1 (q1) corner 2 (q2) corner 3 (q3) corner 4 (q4)
Load Case
------------------------------------------------------
Check For Stability Against Overturning And Sliding
- Factor of safety against sliding Factor of safety against overturning
RPEPL-BCW-ME-
Doc.No: - Rev
------------------------------------------------------
Moment Calculation
Check Trial Depth against moment (w.r.t. X Axis)
ANNEX G G-1.1C
RPEPL-BCW-ME-
Doc.No: - Rev
)=
PROJECT: DEVELOPMENT OF 4.1MW SOLAR 4.1MW-ED-CRA-F11-01 00
PV PLANT, MEDINIPUR,W.B
Date: 12/10/2021 Page 81 of 159
DESIGN CALCULATION FOR MCR
BUILDING FOR 4.1 MW AT
MEDINIPUR,W.B.
ANNEX G G-1.1C
)=
Limit Moment Of Resistance (Mumax
= 21015.772382 kNm
------------------------------------------------------
Shear Calculation
Check Trial Depth for one way shear (Along X Axis)
(Shear Plane Parallel to X Axis)
DX = 0.905 m
RPEPL-BCW-ME-
Doc.No: - Rev
Check Trial Depth for one way shear (Along Z Axis) (Shear Plane Parallel to Z
Axis)
DZ = 0.905 m
Shear Force(S) = 2000.921 kN
RPEPL-BCW-ME-
Doc.No: - Rev
Ks = = 1.000
Ks x Tc = 1250.0000 kN/m2
------------------------------------------------------
Reinforcement Calculation
Calculation of Maximum Bar Size
Along X Axis
Development Length(ld) =
= 1.289 m
Allowable Length(ldb) =
= 3.525 m
RPEPL-BCW-ME-
Doc.No: - Rev
Along Z Axis
Along Z Axis
RPEPL-BCW-ME-
Doc.No: - Rev
Smin <= S <= Smax and selected bar size < selected maximum bar size...
Along X Axis
RPEPL-BCW-ME-
Doc.No: - Rev
Smin <= S <= Smax and selected bar size < selected maximum bar size...
Along Z Axis
1266.874 kNm
Smin <= S <= Smax and selected bar size < selected maximum bar size... The reinforcement is
accepted.
RPEPL-BCW-ME-
Doc.No: - Rev
Ø10 @ 65 mm o.c.
Along X Axis
1266.874 kNm
Smin <= S <= Smax and selected bar size < selected maximum bar size... The reinforcement is
accepted.
Ø10 @ 60 mm o.c.
------------------------------------------------------
RPEPL-BCW-ME-
Doc.No: - Rev
Isolated Footing 9
Input Values
Footing Geomtery
Design Type : Calculate Dimension
Footing Thickness (Ft) : 305.000 mm
Footing Length - X (Fl) : 1000.000 mm
Footing Width - Z (Fw) : 1000.000 mm Eccentricity along X (Oxd) : 0.000
mm
Eccentricity along Z (Ozd) : 0.000 mm
RPEPL-BCW-ME-
Doc.No: - Rev
Column Dimensions
Column Shape : Rectangular
Column Length - X (Pl) : 0.300 m
Column Width - Z (Pw) : 0.300 m
Pedestal
Include Pedestal? No
Pedestal Shape : N/A
Pedestal Height (Ph) : N/A
Pedestal Length - X (Pl) : N/A
Pedestal Width - Z (Pw) : N/A
Design Parameters
Concrete and Rebar Properties
Unit Weight of Concrete : 25.000 kN/m3
Strength of Concrete : 25.000 N/mm2
Yield Strength of Steel : 415.000 N/mm2
Minimum Bar Size : Ø6
Maximum Bar Size : Ø32
Minimum Bar Spacing : 50.000 mm
Maximum Bar Spacing : 500.000 mm
Pedestal Clear Cover (P, CL) : 50.000 mm
Footing Clear Cover (F, CL) : 50.000 mm
Soil Properties
Soil Type : Drained
Unit Weight : 22.000 kN/m3
Soil Bearing Capacity : 100.000 kN/m2
Soil Surcharge : 0.000 kN/m2
Depth of Soil above Footing : 0.000 mm
Cohesion : 0.000 kN/m2
Min Percentage of Slab : 0.000
Sliding and Overturning
------------------------------------------------------
RPEPL-BCW-ME-
Doc.No: - Rev
Number
1 DL
2 LL
3 WX
4 WZ
RPEPL-BCW-ME-
Doc.No: - Rev
RPEPL-BCW-ME-
Doc.No: - Rev
Design Calculations
Footing Size
Area from initial length and width, A o = Lo X Wo = 1.000 m2 Min. area required from
------------------------------------------------------
Area of
Pressure at Pressure at Pressure at Pressure at footing in
Load Case corner 1 (q1) corner 2 (q2) corner 3 (q3) corner 4 (q4) uplift (Au)
(kN/m2) (kN/m2) (kN/m2) (kN/m2)
RPEPL-BCW-ME-
Doc.No: - Rev
(m2)
101 90.7700 93.9958 99.8882 96.6625 0.000
101 90.7700 93.9958 99.8882 96.6625 0.000
101 90.7700 93.9958 99.8882 96.6625 0.000
101 90.7700 93.9958 99.8882 96.6625 0.000
If Au is zero, there is no uplift and no pressure adjustment is necessary. Otherwise, to account for uplift, areas of negative pressure
will be set to zero and the pressure will be redistributed to remaining corners.
Summary of adjusted Pressures at Four Corner
Pressure at Pressure at Pressure at Pressure at
corner 1 (q1) corner 2 (q2) corner 3 (q3) corner 4 (q4)
Load Case
------------------------------------------------------
Check For Stability Against Overturning And Sliding
- Factor of safety against sliding Factor of safety against overturning
RPEPL-BCW-ME-
Doc.No: - Rev
------------------------------------------------------
Moment Calculation
Check Trial Depth against moment (w.r.t. X Axis)
ANNEX G G-1.1C
RPEPL-BCW-ME-
Doc.No: - Rev
)=
PROJECT: DEVELOPMENT OF 4.1MW SOLAR 4.1MW-ED-CRA-F11-01 00
PV PLANT, MEDINIPUR,W.B
Date: 12/10/2021 Page 95 of 159
DESIGN CALCULATION FOR MCR
BUILDING FOR 4.1 MW AT
MEDINIPUR,W.B.
ANNEX G G-1.1C
)=
Limit Moment Of Resistance (Mumax
= 49173.660108 kNm
------------------------------------------------------
Shear Calculation
Check Trial Depth for one way shear (Along X Axis)
(Shear Plane Parallel to X Axis)
DX = 1.207 m
RPEPL-BCW-ME-
Doc.No: - Rev
Check Trial Depth for one way shear (Along Z Axis) (Shear Plane Parallel to Z
Axis)
DZ = 1.207 m
Shear Force(S) = 3308.411 kN
RPEPL-BCW-ME-
Doc.No: - Rev
Ks = = 1.000
Ks x Tc = 1250.0000 kN/m2
------------------------------------------------------
Reinforcement Calculation
Calculation of Maximum Bar Size
Along X Axis
Development Length(ld) =
= 1.289 m
Allowable Length(ldb) =
= 4.700 m
RPEPL-BCW-ME-
Doc.No: - Rev
Along Z Axis
Along Z Axis
RPEPL-BCW-ME-
Doc.No: - Rev
Smin <= S <= Smax and selected bar size < selected maximum bar size...
Along X Axis
RPEPL-BCW-ME-
Doc.No: - Rev
Smin <= S <= Smax and selected bar size < selected maximum bar size...
Along Z Axis
3869.398 kNm
Smin <= S <= Smax and selected bar size < selected maximum bar size... The reinforcement is
accepted.
RPEPL-BCW-ME-
Doc.No: - Rev
Ø10 @ 50 mm o.c.
Along X Axis
3869.398 kNm
Smin <= S <= Smax and selected bar size < selected maximum bar size... The reinforcement is
accepted.
Ø10 @ 50 mm o.c.
------------------------------------------------------
RPEPL-BCW-ME-
Doc.No: - Rev
Isolated Footing 10
Input Values
Footing Geomtery
Design Type : Calculate Dimension
Footing Thickness (Ft) : 305.000 mm
Footing Length - X (Fl) : 1000.000 mm
Footing Width - Z (Fw) : 1000.000 mm Eccentricity along X (Oxd) : 0.000
mm
Eccentricity along Z (Ozd) : 0.000 mm
RPEPL-BCW-ME-
Doc.No: - Rev
Column Dimensions
Column Shape : Rectangular
Column Length - X (Pl) : 0.300 m
Column Width - Z (Pw) : 0.300 m
Pedestal
Include Pedestal? No
Pedestal Shape : N/A
Pedestal Height (Ph) : N/A
Pedestal Length - X (Pl) : N/A
Pedestal Width - Z (Pw) : N/A
Design Parameters
Concrete and Rebar Properties
Unit Weight of Concrete : 25.000 kN/m3
Strength of Concrete : 25.000 N/mm2
Yield Strength of Steel : 415.000 N/mm2
Minimum Bar Size : Ø6
Maximum Bar Size : Ø32
Minimum Bar Spacing : 50.000 mm
Maximum Bar Spacing : 500.000 mm
Pedestal Clear Cover (P, CL) : 50.000 mm
Footing Clear Cover (F, CL) : 50.000 mm
Soil Properties
Soil Type : Drained
Unit Weight : 22.000 kN/m3
Soil Bearing Capacity : 100.000 kN/m2
Soil Surcharge : 0.000 kN/m2
Depth of Soil above Footing : 0.000 mm
Cohesion : 0.000 kN/m2
Min Percentage of Slab : 0.000
Sliding and Overturning
------------------------------------------------------
RPEPL-BCW-ME-
Doc.No: - Rev
Number
1 DL
2 LL
3 WX
4 WZ
RPEPL-BCW-ME-
Doc.No: - Rev
RPEPL-BCW-ME-
Doc.No: - Rev
Design Calculations
Footing Size
Area from initial length and width, A o = Lo X Wo = 1.000 m2 Min. area required from
------------------------------------------------------
Area of
Pressure at Pressure at Pressure at Pressure at footing in
Load Case corner 1 (q1) corner 2 (q2) corner 3 (q3) corner 4 (q4) uplift (Au)
(kN/m2) (kN/m2) (kN/m2) (kN/m2)
RPEPL-BCW-ME-
Doc.No: - Rev
(m2)
101 86.1581 94.3425 98.6470 90.4626 0.000
101 86.1581 94.3425 98.6470 90.4626 0.000
101 86.1581 94.3425 98.6470 90.4626 0.000
101 86.1581 94.3425 98.6470 90.4626 0.000
If Au is zero, there is no uplift and no pressure adjustment is necessary. Otherwise, to account for uplift, areas of negative pressure
will be set to zero and the pressure will be redistributed to remaining corners.
Summary of adjusted Pressures at Four Corner
Pressure at Pressure at Pressure at Pressure at
corner 1 (q1) corner 2 (q2) corner 3 (q3) corner 4 (q4)
Load Case
------------------------------------------------------
Check For Stability Against Overturning And Sliding
- Factor of safety against sliding Factor of safety against overturning
RPEPL-BCW-ME-
Doc.No: - Rev
------------------------------------------------------
Moment Calculation
Check Trial Depth against moment (w.r.t. X Axis)
RPEPL-BCW-ME-
Doc.No: - Rev
)=
PROJECT: DEVELOPMENT OF 4.1MW SOLAR 4.1MW-ED-CRA-F11-01 00
PV PLANT, MEDINIPUR,W.B
Date: 12/10/2021 Page 109 of 159
DESIGN CALCULATION FOR MCR
BUILDING FOR 4.1 MW AT
MEDINIPUR,W.B.
)=
Limit Moment Of Resistance (Mumax
= 9843.238474 kNm
------------------------------------------------------
Shear Calculation
Check Trial Depth for one way shear (Along X Axis)
(Shear Plane Parallel to X Axis)
DX = 0.705 m
RPEPL-BCW-ME-
Doc.No: - Rev
Check Trial Depth for one way shear (Along Z Axis) (Shear Plane Parallel to Z
Axis)
DZ = 0.705 m
Shear Force(S) = 1312.291 kN
RPEPL-BCW-ME-
Doc.No: - Rev
Ks = = 1.000
Ks x Tc = 1250.0000 kN/m2
------------------------------------------------------
Reinforcement Calculation
Calculation of Maximum Bar Size
Along X Axis
Development Length(ld) =
= 1.289 m
Allowable Length(ldb) =
= 2.675 m
RPEPL-BCW-ME-
Doc.No: - Rev
Along Z Axis
Along Z Axis
RPEPL-BCW-ME-
Doc.No: - Rev
Smin <= S <= Smax and selected bar size < selected maximum bar size...
Along X Axis
RPEPL-BCW-ME-
Doc.No: - Rev
Smin <= S <= Smax and selected bar size < selected maximum bar size...
Along Z Axis
449.500 kNm
Smin <= S <= Smax and selected bar size < selected maximum bar size... The reinforcement is
accepted.
RPEPL-BCW-ME-
Doc.No: - Rev
Ø8 @ 50 mm o.c.
Along X Axis
449.500 kNm
Smin <= S <= Smax and selected bar size < selected maximum bar size... The reinforcement is
accepted.
Ø10 @ 75 mm o.c.
------------------------------------------------------
RPEPL-BCW-ME-
Doc.No: - Rev
Isolated Footing 11
Input Values
Footing Geomtery
Design Type : Calculate Dimension
Footing Thickness (Ft) : 305.000 mm
Footing Length - X (Fl) : 1000.000 mm
Footing Width - Z (Fw) : 1000.000 mm Eccentricity along X (Oxd) : 0.000
mm
Eccentricity along Z (Ozd) : 0.000 mm
RPEPL-BCW-ME-
Doc.No: - Rev
Column Dimensions
Column Shape : Rectangular
Column Length - X (Pl) : 0.300 m
Column Width - Z (Pw) : 0.300 m
Pedestal
Include Pedestal? No
Pedestal Shape : N/A
Pedestal Height (Ph) : N/A
Pedestal Length - X (Pl) : N/A
Pedestal Width - Z (Pw) : N/A
Design Parameters
Concrete and Rebar Properties
Unit Weight of Concrete : 25.000 kN/m3
Strength of Concrete : 25.000 N/mm2
Yield Strength of Steel : 415.000 N/mm2
Minimum Bar Size : Ø6
Maximum Bar Size : Ø32
Minimum Bar Spacing : 50.000 mm
Maximum Bar Spacing : 500.000 mm
Pedestal Clear Cover (P, CL) : 50.000 mm
Footing Clear Cover (F, CL) : 50.000 mm
Soil Properties
Soil Type : Drained
Unit Weight : 22.000 kN/m3
Soil Bearing Capacity : 100.000 kN/m2
Soil Surcharge : 0.000 kN/m2
Depth of Soil above Footing : 0.000 mm
Cohesion : 0.000 kN/m2
Min Percentage of Slab : 0.000
Sliding and Overturning
------------------------------------------------------
RPEPL-BCW-ME-
Doc.No: - Rev
Number
1 DL
2 LL
3 WX
4 WZ
RPEPL-BCW-ME-
Doc.No: - Rev
RPEPL-BCW-ME-
Doc.No: - Rev
Design Calculations
Footing Size
Area from initial length and width, A o = Lo X Wo = 1.000 m2 Min. area required from
------------------------------------------------------
Area of
Pressure at Pressure at Pressure at Pressure at footing in
Load Case corner 1 (q1) corner 2 (q2) corner 3 (q3) corner 4 (q4) uplift (Au)
(kN/m2) (kN/m2) (kN/m2) (kN/m2)
RPEPL-BCW-ME-
Doc.No: - Rev
(m2)
101 94.1615 85.4872 89.6981 98.3725 0.000
101 94.1615 85.4872 89.6981 98.3725 0.000
101 94.1615 85.4872 89.6981 98.3725 0.000
101 93.8253 82.8776 87.8174 98.7650 0.000
If Au is zero, there is no uplift and no pressure adjustment is necessary. Otherwise, to account for uplift, areas of negative pressure
will be set to zero and the pressure will be redistributed to remaining corners.
Summary of adjusted Pressures at Four Corner
Pressure at Pressure at Pressure at Pressure at
corner 1 (q1) corner 2 (q2) corner 3 (q3) corner 4 (q4)
Load Case
------------------------------------------------------
Check For Stability Against Overturning And Sliding
- Factor of safety against sliding Factor of safety against overturning
RPEPL-BCW-ME-
Doc.No: - Rev
------------------------------------------------------
Moment Calculation
Check Trial Depth against moment (w.r.t. X Axis)
ANNEX G G-1.1C
RPEPL-BCW-ME-
Doc.No: - Rev
ANNEX G G-1.1C
)=
Limit Moment Of Resistance (Mumax
= 11583.447700 kNm
------------------------------------------------------
Shear Calculation
Check Trial Depth for one way shear (Along X Axis)
(Shear Plane Parallel to X Axis)
RPEPL-BCW-ME-
Doc.No: - Rev
DX = 0.755 m
Shear Force(S) = 1307.329 kN
Check Trial Depth for one way shear (Along Z Axis) (Shear Plane Parallel to Z
Axis)
DZ = 0.755 m
Shear Force(S) = 1342.852 kN
RPEPL-BCW-ME-
Doc.No: - Rev
Ks = = 1.000
Ks x Tc = 1250.0000 kN/m2
------------------------------------------------------
Reinforcement Calculation
Calculation of Maximum Bar Size
Along X Axis
Development Length(ld) =
= 1.289 m
Allowable Length(ldb) =
= 2.750 m
RPEPL-BCW-ME-
Doc.No: - Rev
Along Z Axis
Along Z Axis
RPEPL-BCW-ME-
Doc.No: - Rev
Smin <= S <= Smax and selected bar size < selected maximum bar size...
Along X Axis
RPEPL-BCW-ME-
Doc.No: - Rev
Smin <= S <= Smax and selected bar size < selected maximum bar size...
Along Z Axis
519.086 kNm
Smin <= S <= Smax and selected bar size < selected maximum bar size... The reinforcement is
accepted.
RPEPL-BCW-ME-
Doc.No: - Rev
Ø8 @ 50 mm o.c.
Along X Axis
519.086 kNm
Smin <= S <= Smax and selected bar size < selected maximum bar size... The reinforcement is
accepted.
Ø8 @ 50 mm o.c.
------------------------------------------------------
RPEPL-BCW-ME-
Doc.No: - Rev
Isolated Footing 12
Input Values
Footing Geomtery
Design Type : Calculate Dimension
Footing Thickness (Ft) : 305.000 mm
Footing Length - X (Fl) : 1000.000 mm
Footing Width - Z (Fw) : 1000.000 mm Eccentricity along X (Oxd) : 0.000
mm
Eccentricity along Z (Ozd) : 0.000 mm
RPEPL-BCW-ME-
Doc.No: - Rev
Column Dimensions
Column Shape : Rectangular
Column Length - X (Pl) : 0.300 m
Column Width - Z (Pw) : 0.300 m
Pedestal
Include Pedestal? No
Pedestal Shape : N/A
Pedestal Height (Ph) : N/A
Pedestal Length - X (Pl) : N/A
Pedestal Width - Z (Pw) : N/A
Design Parameters
Concrete and Rebar Properties
Unit Weight of Concrete : 25.000 kN/m3
Strength of Concrete : 25.000 N/mm2
Yield Strength of Steel : 415.000 N/mm2
Minimum Bar Size : Ø6
Maximum Bar Size : Ø32
Minimum Bar Spacing : 50.000 mm
Maximum Bar Spacing : 500.000 mm
Pedestal Clear Cover (P, CL) : 50.000 mm
Footing Clear Cover (F, CL) : 50.000 mm
Soil Properties
Soil Type : Drained
Unit Weight : 22.000 kN/m3
Soil Bearing Capacity : 100.000 kN/m2
Soil Surcharge : 0.000 kN/m2
Depth of Soil above Footing : 0.000 mm
Cohesion : 0.000 kN/m2
Min Percentage of Slab : 0.000
Sliding and Overturning
------------------------------------------------------
RPEPL-BCW-ME-
Doc.No: - Rev
Number
1 DL
2 LL
3 WX
4 WZ
RPEPL-BCW-ME-
Doc.No: - Rev
RPEPL-BCW-ME-
Doc.No: - Rev
Design Calculations
Footing Size
Area from initial length and width, A o = Lo X Wo = 1.000 m2 Min. area required from
------------------------------------------------------
Area of
Pressure at Pressure at Pressure at Pressure at footing in
Load Case corner 1 (q1) corner 2 (q2) corner 3 (q3) corner 4 (q4) uplift (Au)
(kN/m2) (kN/m2) (kN/m2) (kN/m2)
RPEPL-BCW-ME-
Doc.No: - Rev
(m2)
101 93.4426 90.0145 95.8164 99.2445 0.000
101 93.4426 90.0145 95.8164 99.2445 0.000
101 93.4426 90.0145 95.8164 99.2445 0.000
101 92.2562 87.6471 95.3301 99.9393 0.000
If Au is zero, there is no uplift and no pressure adjustment is necessary. Otherwise, to account for uplift, areas of negative pressure
will be set to zero and the pressure will be redistributed to remaining corners.
Summary of adjusted Pressures at Four Corner
Pressure at Pressure at Pressure at Pressure at
corner 1 (q1) corner 2 (q2) corner 3 (q3) corner 4 (q4)
Load Case
------------------------------------------------------
Check For Stability Against Overturning And Sliding
- Factor of safety against sliding Factor of safety against overturning
RPEPL-BCW-ME-
Doc.No: - Rev
------------------------------------------------------
Moment Calculation
Check Trial Depth against moment (w.r.t. X Axis)
ANNEX G G-1.1C
RPEPL-BCW-ME-
Doc.No: - Rev
)=
PROJECT: DEVELOPMENT OF 4.1MW SOLAR 4.1MW-ED-CRA-F11-01 00
PV PLANT, MEDINIPUR,W.B
Date: 12/10/2021 Page 137 of 159
DESIGN CALCULATION FOR MCR
BUILDING FOR 4.1 MW AT
MEDINIPUR,W.B.
ANNEX G G-1.1C
)=
Limit Moment Of Resistance (Mumax
= 48922.774087 kNm
------------------------------------------------------
Shear Calculation
Check Trial Depth for one way shear (Along X Axis)
(Shear Plane Parallel to X Axis)
DX = 1.207 m
RPEPL-BCW-ME-
Doc.No: - Rev
Check Trial Depth for one way shear (Along Z Axis) (Shear Plane Parallel to Z
Axis)
DZ = 1.207 m
Shear Force(S) = 3280.819 kN
RPEPL-BCW-ME-
Doc.No: - Rev
Ks = = 1.000
Ks x Tc = 1250.0000 kN/m2
------------------------------------------------------
Reinforcement Calculation
Calculation of Maximum Bar Size
Along X Axis
Development Length(ld) =
= 1.289 m
Allowable Length(ldb) =
= 4.675 m
RPEPL-BCW-ME-
Doc.No: - Rev
Along Z Axis
Along Z Axis
RPEPL-BCW-ME-
Doc.No: - Rev
Smin <= S <= Smax and selected bar size < selected maximum bar size...
Along X Axis
RPEPL-BCW-ME-
Doc.No: - Rev
Smin <= S <= Smax and selected bar size < selected maximum bar size...
Along Z Axis
3809.241 kNm
Smin <= S <= Smax and selected bar size < selected maximum bar size... The reinforcement is
accepted.
RPEPL-BCW-ME-
Doc.No: - Rev
Ø10 @ 50 mm o.c.
Along X Axis
3809.241 kNm
Smin <= S <= Smax and selected bar size < selected maximum bar size... The reinforcement is
accepted.
Ø10 @ 50 mm o.c.
------------------------------------------------------
RPEPL-BCW-ME-
Doc.No: - Rev
Isolated Footing 16
Input Values
Footing Geomtery
Design Type : Calculate Dimension
Footing Thickness (Ft) : 305.000 mm
Footing Length - X (Fl) : 1000.000 mm
Footing Width - Z (Fw) : 1000.000 mm Eccentricity along X (Oxd) : 0.000
mm
Eccentricity along Z (Ozd) : 0.000 mm
RPEPL-BCW-ME-
Doc.No: - Rev
Column Dimensions
Column Shape : Rectangular
Column Length - X (Pl) : 0.300 m
Column Width - Z (Pw) : 0.300 m
Pedestal
Include Pedestal? No
Pedestal Shape : N/A
Pedestal Height (Ph) : N/A
Pedestal Length - X (Pl) : N/A
Pedestal Width - Z (Pw) : N/A
Design Parameters
Concrete and Rebar Properties
Unit Weight of Concrete : 25.000 kN/m3
Strength of Concrete : 25.000 N/mm2
Yield Strength of Steel : 415.000 N/mm2
Minimum Bar Size : Ø6
Maximum Bar Size : Ø32
Minimum Bar Spacing : 50.000 mm
Maximum Bar Spacing : 500.000 mm
Pedestal Clear Cover (P, CL) : 50.000 mm
Footing Clear Cover (F, CL) : 50.000 mm
Soil Properties
Soil Type : Drained
Unit Weight : 22.000 kN/m3
Soil Bearing Capacity : 100.000 kN/m2
Soil Surcharge : 0.000 kN/m2
Depth of Soil above Footing : 0.000 mm
Cohesion : 0.000 kN/m2
Min Percentage of Slab : 0.000
Sliding and Overturning
------------------------------------------------------
RPEPL-BCW-ME-
Doc.No: - Rev
Number
1 DL
2 LL
3 WX
4 WZ
RPEPL-BCW-ME-
Doc.No: - Rev
RPEPL-BCW-ME-
Doc.No: - Rev
Design Calculations
Footing Size
Area from initial length and width, A o = Lo X Wo = 1.000 m2 Min. area required from
------------------------------------------------------
Area of
Pressure at Pressure at Pressure at Pressure at footing in
Load Case corner 1 (q1) corner 2 (q2) corner 3 (q3) corner 4 (q4) uplift (Au)
(kN/m2) (kN/m2) (kN/m2) (kN/m2)
RPEPL-BCW-ME-
Doc.No: - Rev
(m2)
101 99.6786 91.7212 76.2463 84.2037 0.000
101 99.3872 93.0673 81.0215 87.3414 0.000
101 99.3872 93.0673 81.0215 87.3414 0.000
101 99.3872 93.0673 81.0215 87.3414 0.000
If Au is zero, there is no uplift and no pressure adjustment is necessary. Otherwise, to account for uplift, areas of negative pressure
will be set to zero and the pressure will be redistributed to remaining corners.
Summary of adjusted Pressures at Four Corner
Pressure at Pressure at Pressure at Pressure at
corner 1 (q1) corner 2 (q2) corner 3 (q3) corner 4 (q4)
Load Case
------------------------------------------------------
Check For Stability Against Overturning And Sliding
- Factor of safety against sliding Factor of safety against overturning
RPEPL-BCW-ME-
Doc.No: - Rev
------------------------------------------------------
Moment Calculation
Check Trial Depth against moment (w.r.t. X Axis)
ANNEX G G-1.1C
RPEPL-BCW-ME-
Doc.No: - Rev
)=
PROJECT: DEVELOPMENT OF 4.1MW SOLAR 4.1MW-ED-CRA-F11-01 00
PV PLANT, MEDINIPUR,W.B
Date: 12/10/2021 Page 151 of 159
DESIGN CALCULATION FOR MCR
BUILDING FOR 4.1 MW AT
MEDINIPUR,W.B.
ANNEX G G-1.1C
)=
Limit Moment Of Resistance (Mumax
= 24501.533686 kNm
------------------------------------------------------
Shear Calculation
Check Trial Depth for one way shear (Along X Axis)
(Shear Plane Parallel to X Axis)
DX = 0.955 m
RPEPL-BCW-ME-
Doc.No: - Rev
Check Trial Depth for one way shear (Along Z Axis) (Shear Plane Parallel to Z
Axis)
DZ = 0.955 m
Shear Force(S) = 2135.914 kN
RPEPL-BCW-ME-
Doc.No: - Rev
Ks = = 1.000
Ks x Tc = 1250.0000 kN/m2
------------------------------------------------------
Reinforcement Calculation
Calculation of Maximum Bar Size
Along X Axis
Development Length(ld) =
= 1.289 m
Allowable Length(ldb) =
= 3.700 m
RPEPL-BCW-ME-
Doc.No: - Rev
Along Z Axis
Along Z Axis
RPEPL-BCW-ME-
Doc.No: - Rev
Smin <= S <= Smax and selected bar size < selected maximum bar size...
Along X Axis
RPEPL-BCW-ME-
Doc.No: - Rev
Smin <= S <= Smax and selected bar size < selected maximum bar size...
Along Z Axis
1535.597 kNm
Smin <= S <= Smax and selected bar size < selected maximum bar size... The reinforcement is
accepted.
RPEPL-BCW-ME-
Doc.No: - Rev
Ø10 @ 60 mm o.c.
Along X Axis
1535.597 kNm
Smin <= S <= Smax and selected bar size < selected maximum bar size... The reinforcement is
accepted.
Ø10 @ 60 mm o.c.
------------------------------------------------------
RPEPL-BCW-ME-
Doc.No: - Rev
RPEPL-BCW-ME-
Doc.No: - Rev