Professional Documents
Culture Documents
Most problems getting the X10DR to work with your radio usually come down to simple things easily overlooked. These include: -
1/ Failing to use the XGALA audio level tool (download at x10dr.com) to program the X10DR Mic audio level output from the gateway
so that it matches the radio’s fist mic level.
2/ Failing to program the Gateway so that X10DR speaker level is loud but not distorted.
3/ Forgetting to program or jumper your radio’s interface connector to provide the REQUIRED function input/output on the specified
pins. These include: enabling Emergency input with active low, enabling COR with active low output, Setting radio Rx audio to be
muted when radio is squelched, setting external mic input for analog audio, etc. A number of Kenwood radios need a resistor/s
moved to allow external mic input on their accessory connector.
Other Issues
NO COR available:
Leave pin 6 of X10DR input isolated and let X10DR internal VOX create an internal COR function. There will usually be minimal lost Rx
audio, but if so maybe a syllable lost from Rx audio after no traffic for a while.
No Auto On/Off function:
Make sure the radio/device’s Mic Hi input has a DC voltage on it when powered ON
If not, fit a 100K resistor between X10DR Pin 4 and the host mobile radios switched B+ output.
Noisy Audio
95% of the time this is due to poor earthing of the radio or the X10DR gateway antenna, You can try soldering a ground strap on the
RJ45 exposed shield that plugs into the Gateway base and ground this to nearby vehicle chassis. (refer to X10DR Installation Instruction
Guide for more information- download at: www.x10dr.com)
XCA-M26 Suits Motorola 26 pin Mototrbo XCA-V15M Suits Vertex DB15HD Type 2
XCA-M26T Suits Motorola 26 pin MTM5400 XCA-V25 Suits Vertex DB25
XCA-M16 Suits Motorola 16 pin XCA-T15 Suits Tait DB15 (Non DMR)
XCA-M16T Suits Motorola 16 pin TETRA MTM800 XCA-T15D Suits Tait TM9300 DMR radio
XCA-APX Suits Motorola APX/XTL XCA-T15A Suits Tait DB15 (Non DMR) Emerg Pin1
XCA-VM9 Suits Kenwood/EFJ VM900 DB25 XCA-H26 Suits Hytera MD68/78X
XCA-K25 Suits Kenw.DB25: NX700/TK5710/TK7180 etc XCA-R25 Suits RELM/BK DB25
XCA-K25N Suits Kenw. DB25 NX700/TK5710/7180 Type 2 XCA-R15M Suits RELM/BK G/DMH DB15HD Type 2
XCA-K25A Suits Kenwood DB25 TK690/790 etc XCA-T26M Suits Teltronic DB26 Type 2
XCA-K25M Suits Kenwood DB25 TK690/790 etc Type 2 XCA-C26M Suits Airbus TMR DB26 Type 2
XCA-K15D Suits Kenwood DB15HD for NX720 XCA-HXGM Suits Harris XGT/M7300 Type 2
XCA-K15S Suits Kenwood DB15HD for TK8360/7360 XCA-H37 Suits Harris M7100
XCA-RJK Suits Kenwood simple low end radios Type 3 XCA-X44 Suits Harris XL-185/200 (DB44)
XCA-I25A Suits Icom DB25 XCA-X25 Suits Harris XL-185/200 (DB25)
XCA-I15M Suits Icom DB15HD Type 2 XCA-EXP Suits Cobham Satelite
XCA-RJi Suits Kenwood simple low end radios Type 3 XCA-XMC Converts XMC cables for 2nd Gen X10DR
XCA-G25M Suits GME DB25 Type 2 XMC-RJ45 Converts XIC cables for 1st Gen X10DR
XCA-SD6 Suits Simoco SDM600 XCA-RJ PTT & Emergency buffered output adaptor
XCA-SD7 Suits Simoco SDM700
XCA-SRG Suits Sepura SRG3900 XCA-GEN Generic RJ45-F adaptor for self assembly
XCA-SRM Suits Simoco SRM9000 XCA-U15M Generic partially term DB15 male Type 2
XCA-U25M Generic partially term DB25 male Type 2
*Interface diagrams are believed to be correct at time XCA-CUS New model- Custom configuration*
*MOQ 200 - Call for pricing-delivery
of publication or revision. If in doubt please check radio
manufacturer’s service manuals to confirm your requirement. XIC series Interface cables
XEC-4.5 Extension cables
Please advise if you find errors and they will be quickly rectified.
S
1
shield DC Ground shield/drain Shield 3A FB fuse
8*
2
__
Vbus
__
USB / MAP ID Ground
4
MAP ID 2 MAP ID 1
6
SW B+ Power Ground
8
18cm
Spkr
- Spkr+
10
Tx Audio Audio Ground
11
12
Aux Audio Out 1 / RxD Rx Audio
13
14
INSTALLATION NOTES:
_
Aux Audio Out 2 / TxD Ground
15
16
as required WH
_
GP5 1 (PTT) Ground
_
17
18
Shielded black
connects battery RED
_
GP5 2 (Monitor)
19
GP5 6
_
20
Female 3A
_
21
22
GP5 3 (Chan Act) GP 5 7
Emerg Sw GP5 8
_
23
50cm 24
25
26
Ign Sense VIP 1 (Ext Alarm)
Copyright WCL 2020 Rear View Date: Aug 12th 2019 Revision: 2
XMC-M26 Mototrbo Set-up P 1/4
Conventional & Connect Series Now Select GPIO Physical Pins
Under Accessories
- Set Pin#17 to Ext Mic PTT*
-Set RX Audio type to : Filtered Squelch
-Active
level Low
-Set Pin #21 to PL/Talkgroup Detect*
-Active level : Low
* not applicable to Connect Series
Connect Plus: In Option Board CPS:
In “General Settings”:Leave Hot Mic Source Front
Accessory
S
1 Battery
DC Ground shield/drain Shield 3A FB fuse
shield 8
D+ D
- _
2
__
Vbus
__
USB / MAP ID Ground
4
MAP ID 2 MAP ID 1
6
18cm SW B+ Power Ground
8
Spkr
- Spkr+
10
11
12
Rx Audio
13
14
Tx Audio
INSTALLATION NOTES: Un-stripped
as required WH
_
Aux Audio Out 2 / TxD
15
16
Shielded black
_
GP5 1 (PTT)
17
Ground
_
18
connects battery RED
Female 3A
_
GP5 2 (Monitor) 19 GP5 6
_
20
Connects to drain/shield
_
21
22
GP5 3 (Chan Act) GP5 7
_
23
24
25
26
S
1 may sound in Secure Mic depending on radio’s COR
shield DC Ground shield/drain Shield 3A FB fuse
7 performance.
BEWARE:
Motorola 16 Pin before attempting connection for GTX/LTS refer their
specific service manual.
18cm
50cm
Note:
Motorola have over the years used the 16 pin
connector on a wide variety of models.You
Female RJ45 shielded should check the radio programming and/or
jumpering to ensure correct operation of the
Remote/ footswitch/Handle bar PTT Br BAT81S or similiar
8 WH X10DR unit.
Ext PTT to radio Wh/Br
7 3
COR/ Audio unmute from radio Gr **Emergency function needs to be
6
Mic Lo Wh/Bl programmed into the radio and Pin 9 assigned
5 7 to become operational.
Ext Mic Hi Output/Radio On detect Bl
4 2
Radio Receive audio Wh/Gr
3 11
Emergency output to radio Or
2 9**
Power nominal +12VDC Wh/Or
Battery
S
1
DC Ground shield/drain Shield 3A FB fuse
shield 8
Motorola 16 Pin
18cm
50cm
Battery
(Red)
1 Power nominal +12VDC
1
S
SH DC Ground 3A FB fuse
SH
shield 1
RJ45 Ignition
shielded 25
Female SPK + 20
Motorola
style SPK - 26
Motorola
XTL/APX 26 Pin
18cm
VIEW FROM WIRESI
DE
HDDB26P SPKR+
20 7
connector SPKR-
26 13
CHAN ACT
19 6
I
GNI
TION
25 12
Shielded Black 18 5
female SW B+
24 11
17 4
MIC HI
23 10
Speaker
4A PTT
16 3
blade fuse connector 22 9
EMERGENCY
15 2
RED 18AWG RX_FI
LT_AUDI
O
WH GROUND
21 8
(hi temp) 14 1
3.1meter
RED Shield
UL1332 (18#)
22AWG 3A
50cm 50cm
Copyright WCL 2020 Date: April 22nd 2020 Revision: 4
XCA-VM9 Interface cable:
for Kenwood/EFJViking VM900
Male DB25 for EFJ pigtail UDDI/PVP
Notes:
Program radio connector
pin 4: Emergency Input
Interface brd DB25 shielded male
8 Remote/ Handle Bar PTT
8
BAT81S or similiar 7 Ext PTT to radio WH
7 1
6 COR/ Radio Speaker unmute
6 6
5 Mic Lo
5 19
Battery
(Red)
1 Power nominal +12VDC
1
S
SH DC Ground
SH
shield
24 3A FB fuse
as required WH
connects battery RED
3A
Female
50cm
Shielded Black
18cm
3 17
JSB SWB+
14
2 Emergency Output Battery
2 8 (Red)
1 Power nominal +12VDC
S
1
shield SH DC Ground 3A FB fuse
SH 7
RJ45 DB25 shielded male
shielded
Female
as required WH
connects battery RED
3A
Female Un-stripped
50cm
Shielded Black
RJ45 shielded to DB25
- Male molded style
18cm
DB24 Pin 4: I/O = Input, Function = Ext PTT (voice) Active = Low, Debounce=Yes
DB24 Pin 8: I/O = Input, Function = Emergency Active = Low, Debounce=Yes
DB24 Pin 24: I/O = Output, Function = TOR, Active = Low
Mic PTT Mic Line = Connect, Mi2 = Disconnect, DI Line =Disconnect, With QT/DQT=Yes, With STE=Yes
Ext PTT Mic Line = Disconnect, Mi2 = Connect, DI Line =Disconnect , With QT/DQT=Yes, With STE=Yes
DI level = -1
DEO level = +4
S
Female RJ45 shielded
DB25 shielded male
Refer Kenwood TK690 service manual.
Remote/Handle bar PTT
8 Pin 13 ships from the factory as a Data
Ext PTT to radio
7 4 4 21 input. Swapping the 0 ohm resistor
COR/ Audio unmute from radio
6 23 24 20 from R641 to R640 changes pin 13 to
Mic Lo
5 25 25 25 the required analog Mic Hi input.
Ext Mic Hi Output/Radio On
4 8.2K 13 6 6
Radio Receive audio TK-*90 Radio Control Unit PCB
3 17 17 17
100K
Emergency output to radio
2 5 13 13
Power nominal +12VDC
1 14 14 14
shield DC Ground shield/drain
7 shield shield
DEFAULT
Pin Outs Pin Outs Pin Outs
TK690/ NX700 TK8150
TK590/ TK8180/ etc
etc TK5710/
etc
50cm
RED
3A
S
Female RJ45 shielded DB25 shielded male
Set external Mic sensitivity for “low”when
Remote/Handle bar PTT
8 available in the field programmer.
Ext PTT to radio
7 4
COR/ Audio unmute from radio
6 24
Mic Lo
5 25
Ext Mic Hi Output/Radio On
4 8.2K 6
Radio Receive audio
3 17
100K
Emergency output to radio
2 8
Power nominal +12VDC
1 14
shield DC Ground shield/drain
7
50cm
RED
3A
Once one side is loose, do the same for the other side.
Complete
3 4
JSB SWB+ 1
2 Emergency Output Battery TK7360 Radios
2 7 (Red)
1 Power nominal +12VDC ??
S
1
SH
shield SH DC Ground 15
3A FB fuse
as required WH
connects battery RED
3A
Female
Shielded Black
50cm
18cm
3 3
JSB SWB+ 1 NX3720 Radios
2 Emergency Output Battery Move radio chip jumper R613 to R612
2 7 (Red) Move radio chip jumper R659 to R601
1 Power nominal +12VDC
S
1
SH
shield SH DC Ground 15
3A FB fuse
as required WH
connects battery RED
3A
Female
Shielded Black
50cm
18cm
3
JSB SWB+ Plug dual 3.5 “Y” adaptor into radio speaker
14 socket. Plug 3.5 plug from XCA into one 3.5 jack
2 Emergency Output Battery
2 7 Plug radio external spk into other 3.5 jack.
(Red)
1 Power nominal +12VDC Set Radio volume control for normal listening
S
1
shield SH DC Ground 3A FB fuse level, then use programmer to adjust X10DR
SH 15 Rx audio level on gateway cradle for desired
RJ45 DB15HD shielded male
listening level from X10DR Spk Mic.
shielded
Female Y adaptor sourcing:
http://www.amazon.com/Headphone-Splitter-
3.5mm
Stereo-3-5mm-Adapter/dp/B0002ZPK4O or
mono similiar. (can be mono)
18cm
S
1
SH
DC Ground 6 3A FB fuse
3.5mm
mono
plug
Connect
Sleeves 3.5mm
mono
jack
50cm
Female RJ45 shielded male
Shielded Black
3A
BATT
Spk Connection:
S
Battery
Female RJ45 shielded Pin 19: EPTT
100K
2 15
Power nominal +12VDC
1 11
DC Ground shield/drain
shield 14
as required WH
connects battery RED
Female 3A
Shielded Black 50cm
18cm
S
14 - Ext PTT
Female RJ45 shielded
Remote/ footswitch/Handle bar PTT BAT81S or similiar
8 WH
Ext PTT to radio
7 14
COR/ Audio unmute from radio
6 11
Mic Lo
5 3
Ext Mic Hi Output/Radio On detect
4 13 DB15HD (VGA style) shielded male
Radio Receive audio
3 7
Emergency output to radio
100K
2 4
Power nominal +12VDC
1 15
DC Ground shield/drain
shield 1
18cm
INSTALLATION NOTES:
as required WH
Female
Shielded Black
connects battery RED
3A
Connects to drain/shield
DB15HD (VGA style)
D-SUB CONNECTOR
50cm molded -MALE
S
1 Battery
shield
DC Ground 3A FB fuse
7
shield/drain
Battery
3A
50cm
S
Female RJ45 shielded DB25 shielded male
Remote/ footswitch/Handle bar PTT BAT81S or similiar
8 WH
Ext PTT to radio
7 3
COR/ Audio unmute from radio
6 6
Mic Lo
5 2
Ext Mic Hi Output/Radio On
4 5
Radio Receive audio
3 8
100K
Emergency output to radio
2 11
Power nominal +12VDC
1 7
shield DC Ground shield/drain
9
10
YEL Ignition
10cm
Ignition YEL
as required WH
connects battery RED
Female 3A
50cm
Shielded Black
Un-stripped
18cm
NOTES:
3A FB fuse Radio Programming:
Battery
S
Female RJ45 shielded Pin 5 Call knockdown*
BAT81S or similiar WH Pin 6 PTT
Remote/ footswitch/Handle bar PTT
8 2 Pin 14 Emerg Input
Ext PTT to radio
7 6 Pin 15 Valid signal
COR/ Audio unmute from radio
6 15
Mic Lo 2.2k
5 7 * requires a custom XSJB
Ext Mic Hi Output/Radio On detect
4 4 DB15 shielded male
accessory
Radio Receive audio
3 1
Emergency output to radio
2 14
Power nominal +12VDC 2.2k
1 3
shield
DC Ground shield/drain
2.2k
13
5*
PUR
as required WH
3A
connects battery RED
Knock down input PUR
Female
Shielded Black
Un-stripped
50cm
18cm
NOTES:
3A FB fuse Radio Programming:
Battery
S
Female RJ45 shielded DB26HD-Female
PRGM_IO1 = Output, Active
Low, Speaker-ON
Remote/ footswitch/Handle bar PTT BAT81S or similiar
8 WH
Ext PTT to radio
7 16&20 Yellow is Radio Ignition On/Off
COR/ Audio unmute from radio
6 14 control wire.
Mic Lo
5 5
Ext Mic Hi Output/Radio On detect
4 10k 7
Radio Receive audio 10k
3 8
Emergency output to radio 100k
2 13
Power nominal +12VDC
1 4
shield
DC Ground shield/drain
10k
11
17
26
YEL ( Ignition)
DB26HD - Female
molded style
as required WH
3A
connects battery RED
Ignition control YEL
Female
Shielded Black
Un-stripped
50cm
18cm
RED 24AWG -normally this is ignition sense input, but some SRM9000 models may be
internally modified/jumpered to make this an emergency input. In such cases join RED to BLU BLK (Spk socket)
Orange.
RED
"YELLOW"CRIMP
RED 24AWG ignition In JOINERS FITTED
BLACK
ORANGE- Emerg Output
DB15 -M
PURPLE - Handle bar PTT D-SUB CONNECTOR
BLUE
1
BLACK
2
150cm DB15 -F
D-SUB
DB15 -HD-M
D-SUB
24AWG*15C +ADB
NOTES:
3A FB fuse Radio Programming:
Battery Pin 13 COR/Spk unmute
S
Female RJ45 shielded
HDB15 (VGA Style)
Pin 14 Emerg Input
shielded male
8
7
Ext PTT to radio
6
6
COR/ Audio unmute from radio
13
5
Mic Lo
3
4
Ext Mic Hi Output/Radio On detect 8.2K
0.47uF
1
3
Radio Receive audio
2
Emergency output to radio
100K
2 14
Power nominal +12VDC
1 4
shield
DC Ground shield/drain
15
50cm
3A FB fuse
Battery
S
RJ45 shielded female DB25 shielded male
100K
2 Emergency output to radio
2
1 Power nominal +12VDC
14
DC Ground shield/drain
shield 7&18
50cm
DB25P
D-Sub connecto-MALE
RED
3A
3 17
JSB SWB+
14
2 Emergency Output Battery
2 2 (Red)
1 Power nominal +12VDC
S
1
shield SH DC Ground 3A FB fuse
SH 7
RJ45
shielded DB25 shielded male
Female
as required WH
connects battery RED
3A
Female Un-stripped
50cm
Shielded Black
RJ45 shielded to DB25
- Male molded style
18cm
Notes:
3A FB fuse Program Radio connector
Battery 2- Send Mic to radio spk*
S
RJ45 shielded female
DB15 shielded male 4- ignition sense
Remote/ footswitch/Handle bar PTT BAT81S or similiar 5- Emerg in
8 WH
Ext PTT to radio 10 - Busy out
7 2&12
COR/ Audio unmute from radio 12 - PTT in
6 10
Mic Lo 13 - Audio tap out
5 15
Ext Mic Hi Output/Radio On detect 14 - Audio Tap In
4 14
Radio Receive audio
3 13
2.2K
Emergency output to radio * when radio permits
2 5
Power nominal +12VDC
1 4
DC Ground shield/drain
shield 15
1K
18cm
S
RJ45 shielded female
DB15 shielded male
4- ignition sense
Remote/ footswitch/Handle bar PTT BAT81S or similiar WH
5- Emerg in
8
Ext PTT to radio 7 - Audio Tap In (T3)
7 2&12
COR/ Audio unmute from radio 10 - Busy out
6 10
Mic Lo 12 - PTT in
5 15
Ext Mic Hi Output/Radio On detect 1uF 13 - Audio tap out
4 7
Radio Receive audio
3 13
100K
Emergency output to radio
600
2 5 * when radio permits
Power nominal +12VDC Use gateway tuner to increase gateway
1 4 audio outout to +12dBm
DC Ground shield/drain
shield 15
1uF
100k 8
22K
1K
18cm
S
RJ45 shielded female J1A 4- ignition sense
J8A
Remote/ footswitch/Handle bar PTT J8 WH 1- Emerg in
8
7 Ext PTT to radio
2&12 10 - Busy out
COR/ Audio unmute from radio 12 - PTT in
6 10
Mic Lo 13 - Audio tap out
5 15
4 Ext Mic Hi Output/Radio On detect
14 14 - Audio Tap In
Radio Receive audio
3 13
Emergency output to radio J2 * when radio permits
2 1
12Volt DC J1
1 4
shield DC Ground J9 shield
PCB-X10-033-2A J10 YEL (ignition sense)
18cm
5
5 Mic Lo 17
8.2K
J4P Ext Mic Hi Output(AC/8.2)
J4I Ext Mic Hi Output(AC) 7
1uF 4 Ext Mic Hi Output (DC)
4
3 Radio Receive audio
100K
3 8
JSB SWB+ 4
2 Emergency Output Battery
2 14 (Red)
1 Power nominal +12VDC
S
1
SH
shield SH DC Ground 2 3A FB fuse
PHOTO:TO BE
RJ45 6
shielded Internal Spk. Enable (cut) Orange UPDATED
13
Female External Speaker - Grey
9
External Speaker + Grey
18
External alarm out Purple
5
Ignition sense Yellow
26
Remote PTT WH 3A
connects battery RED
Ignition Sense YEL
Female Ext Alarm Out PUR
Shielded Black Spk + GRY
Spk- GRY
Ext Spk Select ORG Orange-Cut forInt Spk
18cm
Notes:
Program radio Pin 23 for “cor”.(radio
speaker unmute)
Radio Emergency input is open circuit
trigger (active high)
3A FB fuse
Battery
S
Female RJ45 shielded
g 10k 9
1 Power nominal +12VDC s
100k
20
21
8.2k 7
DC Ground ESD5Z12T1G ESD5Z12T1G
shield 4
as required WH
connects battery RED
3A
Female
50cm
Shielded Black
18cm
Notes:
Program radio Pin 1 for Emergency.
3A FB fuse
Battery
S
Female RJ45 shielded DB15HD (VGA styl;e) shielded male
100K
Emergency output to radio
2 1*
Power nominal +12VDC
1 15
shield
DC Ground shield/drain
6
50cm
RED
3A
3A FB fuse
Battery
S
Female RJ45 shielded DB26HDM shielded male
BAT81S or similiar
Remote/ footswitch/Handle bar PTT
8 WH
Ext PTT to radio 23*
7
COR/ Audio unmute from radio 26***
6
Mic Lo 13
5
Ext Mic Hi Output/Radio On detect 8*
4
Radio Receive audio 9
3
100K
Emergency output to radio 24**
2
Power nominal +12VDC 22
1
shield
DC Ground shield/drain
shield
DB26HDM - Male
as required WH
molded style
connects battery RED
3A
Female
50cm
Shielded Black
18cm
3A FB fuse
Battery
S
Female RJ45 shielded
5
N/A
1k
8
100k
14
10k
7 Ext PTT to radio d
g
6 COR/ Audio unmute from radio s
2N7002 16
5 Mic Lo
9
10k
4 Ext Mic Hi Output/Radio On
8
3 detect DB26HDM shielded female
18
2 Radio Receive audio
4
1 Emergency output to radio
Power nominal +12VDC
shield/drain
shield 10
DC Ground
DB26HDM - Female
as required WH molded style
connects battery RED
3A
Female
50cm
Shielded Black
18cm
Notes:
Use RPM to select I/O and
function required.
S
Female RJ45 shielded DB44 shielded male
100K
Emergency output to radio
2 25
Power nominal +12VDC
1 28
shield
DC Ground shield/drain
7
as required WH
connects battery RED
3A
Female
50cm
Shielded Black
18cm
Notes:
Use RPM to select I/O and
function required.
S
Female RJ45 shielded DB37 shielded male
shield
DC Ground shield/drain
7
as required WH
connects battery RED
3A
Female
50cm
Shielded Black
18cm
8
Remote/Handle bar PTT WH Program Radio Connector
7
Ext PTT to radio 2 - program for Ext_Unmute (Active Lo)
35 35 - program for Ext_PTT
6
Ext_Audio unmute from radio 34 - program for Emergency
2
5
Mic Lo
3 Gateway Audio Level Adjustment
4
Ext Mic Hi Output/Radio On detect
5 Set Gateway Audio Out to “18”
3
Radio Receive audio
20 VOX sensitivity
Emergency output to radio
2 34 Set VOX sensitivity for “60”
1
Power nominal +12VDC
11
shield
DC Ground
7
shield/drain
28
27
UL1007 22#,
Speaker Socket
TYCO 61314-6
and 1-480318-0, or
equivalent
18cm
WH
Female
Shielded
Black
Grey
BLK
Speaker Socket
TYCO 61314-6
and 1-480318-0, or
equivalent
165cm
S
Female RJ45 shielded DB25 shielded Male
shield
DC Ground shield/drain
1
as required WH
connects battery RED
3A
Female
50cm
Shielded Black
18cm
Notes:
Use RPM Radio Programmer to assign
RJ45 shielded to DB25 I/O functions:.
Female RJ45 shielded - Male molded style
Program Radio Connector
8
Remote/Handle bar PTT BAT81S or similiar
WH 2 - program for Ext_Unmute (Active Lo)
7
Ext PTT to radio 35 - program for Ext_PTT
3 34 - program for Emergency
6
Ext_Audio unmute from radio
22
5
Mic Lo Gateway Audio Level Adjustment
12 Set Gateway Audio Out to “18”
4
Ext Mic Hi Output/Radio On detect
24
3
Radio Receive audio VOX sensitivity
16 Set VOX sensitivity for “60”
2
Emergency output to radio
21
1
Power nominal +12VDC
25
shield
DC Ground
10
shield/drain
Female
Shielded Black
WH
18cm
3 2
JSB SWB+ 3
2 Emergency Output Battery
2 5 (Red)
1 Power nominal +12VDC
S
1
SH
shield SH DC Ground 15 3A FB fuse
as required WH
connects battery RED
3A
Female
Shielded Black
50cm
18cm
50cm
26#4P+AB OD:6.0MM
DB15 Receptacle
- Male- Molded
100K
shield 9 &SH
1
DB15 Plug
- Female
100K
1
1 DC Power nominal +12VDC
shield/drain
shield DC Ground
Switched B+ nominal +12VDC
suggested interface
NOTES:
1/Connect 100K resistor between pins 4 and radio switched B+ output so X10DR turns on when 12VDC
is applied. Other wise connect to PIn one so is always on. Gateway can be manually turne off
Pin 4 connects to external device Mic Hi input should be capacitively coupled: 0.47-1uF
2/ Note: If host radio Mic Hi has DC voltage only when radio is powered on (Electret Mic Bias) 100K
and 0.47uF cap not required.
3/ If remote PTT is used then active ground switch should be via a series diode to protect Gateway
input circuitry
* if Audio unmute indicate is not available from host device leave pin unconnected ( X10DR will de-
tect receive audio to enable handset speaker.
Female RJ45
shielded
Male DB25
unterminated
7
COR/ Audio unmute from radio yel
6
Mic Lo grn
5
Ext Mic Hi Output red
4
Radio Receive audio blk
3
Not Used org
2
Power nominal +12VDC blu
1
S
External Mic Audio to be enabled. For auto off/on some radios 3A FB fuse
require a 100K resistor to be fitted between SwB+ and the Mic
Mic Hi output (pin 4) * also refer X10DR manual page.
50cm
RED
3A
DB25M -RJ45F
Female RJ45
shielded
Male DB15
unterminated
7
6
COR/ Audio unmute from radio yel
5
Mic Lo grn
4
Ext Mic Hi Output red
3
Radio Receive audio blk
2
Not Used org
1
Power nominal +12VDC blu
Always check the radio service manual and radio programming
guide details to ensure the right connections are provided on
the designated pins of the radios interface connector*. Battery
Note: some radios require standard jumpers to be fitted to allow
S
External Mic Audio to be enabled. For auto off/on some radios 3A FB fuse
require a 100K resistor to be fitted between SwB+ and the Mic
Mic Hi output (pin 4) * also refer X10DR manual page.
50cm
RED
3A
DB15M -RJ45F
8
Remote/ footswitch/Handle bar PTT
8
7
Ext PTT to radio
7
6
COR/ Audio unmute from radio 6
5
Mic Lo 5
4
Ext Mic Hi Output/Radio On detect 4
3
Radio Receive audio 3
2
Emergency output to radio 2
1
Power nominal +12VDC 1
DC Ground shield/drain
shield shield
50-620 cm
26#4P+AB OD:6.0MM
450 cm
26#4P+AB OD:6.0MM