Professional Documents
Culture Documents
Parts list:
1. 3. 3. 9.
1.
11.
4. 5. 5. 10.
12.
4.
4. 13.
7.
8.
2. 14.
6. 8.
Note:
Put any loose parts ordered on the ground and check the numbers! Shed there, where necessary,
rough parts are smooth. Check before you glued, or glueing the right parts.
Read the installation requirements before you begin. Good luck with the installation!
step 2.
Push al the slats together so that there is even spacing on
each side. Screw only the centre slat down using screws in
the pre-drilled holes*
*Before tightening has screwed this slats, first apply a very
thin layer of glue (Tec7) in the middle of the bar screwing.
step 3.
Space the slats out evenly, from the centre attached slat, so
that the shortest outside slats are even with end of the curve
on the back supports, and then attach.
Use a thin slat as a template. When the top is nice and round,
you can the slats glued (Tec7) and screw.
step 4.
Attach the legs (1) to the sides (8) using four screws in the
pre-drilled holes as shown. Line up the screws with the pilot
8. 8. holes on the leg. Each leg and side are marked either “L” for
1. left and “R” for right, and should be matched together.
1.
8.
step 5.
Place the two sides (8) marked “L” and “R” facing each other
with the legs on the outside. The “R” should be on the right
side of the chair (as sitting) Attach the front slat (12) to the
front of the sides as shown. Using four screws and use Tec7.
12.
6.
8.
step
Place back assembly into the cut out area on the sides as
shown, attach with two screws through the pre-drilled holes.
Don’t forget Tec7!
step 8.
3. Attach each arm support(3) to the tops of the legs with
4. two screws. Push a triangle (4) into the right angled corner
(lining up the two pre-drilled holes in the leg and the centre
pre-drilled hole on the arm support) and attach with three
screws. Repeat on the other side. Use Tec7.
step 9.
Attach the top of the struts (7) to the underside of the top
back support (11) with two screws in the pre-drilled holes.
If the back assembly is noticeably leaning off centre, grasp it
firmly and move it left or right until the bottom of the struts
7.
can be attached without twisting or bending them. Attach the
7. bottom of the struts to the sides with one screw each for now.
Do not apply glue here yet.
step 10.
Attach the back of the arm (5) to the strut with one screw
through the pre-drilled hole on the strut. Attach the front
of the arm to the arm support (3) with two screws from the
under side.
First drill a hole with 3 mm wood drill bit Use glue Tec7!
step 11.
Place the chair on a flat surface and make sure it is sitting
solid on both legs and both sides. If it is not sitting flat,
remove the single screw holding the bottom of the strut
down and move the strut up or down to compensate. When
the adjustments are done, attach the struts with two screws
each (and glue Tec7).
step 12.
Attach the additional arm support (#6) to the inside of the
struts, underneath the back of the arms through the pre-dril-
led holes with four screws.
6. Pre-drill with a wood drill bit (3 mm) is recommended.
step 13.
Knock the caps under the legs and fit the brass plate on the
front of the chair.
step 14.
Remove any adhesive from the chair and sanding rough parts
smooth. Your seat is ready for use.
You have chosen a kit box . The supplier is responsible for the supplied loose
parts. You are responsible for assembling !
Use only the screws ! These are made of stainless steel and do not rust .
Use only a Canadian Bitje , guaranteed to turn the screws otherwise broken.
Use for bonding only Tec7 . This adhesive is suitable for indoor and outdoor use . In all weathers . Always
bonding portion light rub , not both parts !
Cedar wood is light and delicate. So beware of dents . Tighten the screws . But beware : fixed is fixed !
If you follow the above steps carefully , you can mount the seat in a good way . We wish you much fun with the
bear chair , and refer to service to our website .
info@the-bearchair.nl
www.the-bearchair.nl
0343-513741