Professional Documents
Culture Documents
)
Contractor:- Mettle Infra, Bhopal
DESIGN CALCULATION
UNDER- GROUND WATER RESERVOIR 50.0 K.L.
FOR
E.E. P.H.E. Salikheda, Astha, Sihore (M.P.),
Design Consideration
1. Design has been done as per IS : 3370 Part II, Part-IV, IS 456, SP16
2. Grade of Concrete is M30 as per IS : 456 - 2000.
3. Grade of Reinforcement Steel is Fe500 as per IS : 1786
4. Net Safe Bearing Capacity of soil has been considered as 15 T/m² at Founding Level, i.e 1.5 m
Design Methodology :
This design is for a RCC well to store water. This is designed as a cylindrical tank with hinged base.
Coefficients for tension shear and moments are taken from relevent table and methods from IS 3370(part IV).
Another moment for hoop stress generated from soil pressure has been considered .
All design moments/ shear has been derived for critical load case : empty tank with full earth pressure outside.
for calculation of earth pressure Earth pressure at rest has been considered.
Design Data
1. Inner Dia of water tank = 4.5m
2. Depth of water tank = 2.0m Below F.G.L. & + 1.30 m Above F.G.L.
Design of Circular Water Tank:
Design Parameters:
Water tank Dimension: Diameter (D): 4000 mm 4460
Depth below GL = 11000 mm Height above GL = 500 mm
Deoth of ground water table from top of base slab : 10000 mm
Wall thickness = 230 mm Base Slab thickness = 230 mm
Conc Grade : M30 Reinf Grade : Fe 500
st= 1.5 N/mm 2 sct = 2.0 N/mm 2 scc = 8.0 N/mm 2 scbc = 10.0 N/mm 2
Refer Table - 1 of IS 3370 (Part II): Refer Table - 21 of IS 456 : 2000
m =280 / ( 3 x scbc ) = 9.33
Liquid face sst = 190 N/mm 2 k = 93.33 / ( sst + 93.33 ) = 0.329 j=1-k/3= 0.89
(Cl. 4.4.3.1; IS 3370 :Part II) R = 1/2 scbc k j = 1.464 N/mm 2
Remote face sst = 190 N/mm 2 k = 93.33 / ( sst + 93.33 ) = 0.329 j=1-k/3= 0.89
(Cl. 4.4.3.1; IS 3370 :Part II) R = 1/2 scbc k j = 1.464 N/mm 2
When tank is empty=
sst = 230 N/mm 2 k = 93.33 / ( sst + 93.33 ) = 0.289 j=1-k/3= 0.904
R = 1/2 scbc k j = 1.306 N/mm 2
Density of Content = 10 kN / m3 Surcharge= 0 kN/m2
Densty of Conc. = 25 kN / m3 Net SBC of Soil = 120 kN/m2
Density of soil = 16 kN / m 3
230
AATVIK CONSULTANCY INFRASTRUCTURE 50 K.L. Under Ground Sump Well at Salikheda, Sihore (M.P.)
P.H.E.SIHORE (M.P.)
Contractor:- Mettle Infra, Bhopal
0.5 x 0 =
10000 11500 11000 0 kN / m2
5*9.5
230
10x11.5=
115 kN / m2 0.5 x (16 - 9.88) x 10 = 30.6 kN / m2
9.88 x 10= 98.8 kN / m2
Total pressure due to earth & water = + 30.6 + 98.8
= 129.4 kN/m2
Design of Tank Wall :
Case - I ( Inside Full & Outside no earth for wall) 4460
Refer Table - 9 of IS 3370 (Part-IV) 230 4000 230
For H /Dt
2
= 143.8 Coeff = 0.687
Max hoop tension occures at 0.7 H from top Free
Max Hoop tension = 0.687 x 115 x 4 / 2 =
= 158.01 kN/m H= 11500
Steel reqd= 158.01 x 1000 / 190 = 831.63 mm2
(Horizontal) Fixed
Provide 8 dia @ 110 c/c in each face.
Total Ast provide in both faces = 913.9 mm2 INCREASE
Minimum % of reinforcement (TMT bar) required: 0.21% H2/Dt = 143.8 wH= 115 kN/m2
Minimum reinforcement reqd in both faces: 2 x (0.21)/100 x 1000 x 230 = 966 mm2
Tensile stress in concrete:
=158010/((230x1000)+((9.33-1)x913.9)) = 0.66 N/mm2 < 1.5 N/mm2 (Table-1 I.S.3370 Part-II) O.K
Refer Table-10 of IS 3370 (Part- IV):
For H2/Dt = 143.8 Coeff = -0.0079 Max B.M occures at 1.0 H from top
Maximum B.M. per meter height (Tension at liquid face) : 0.0079 x 115 x 11.5^2 = 120.15 kN-m/m
Depth reqd. for uncracked section (D) = Ö (6x120.15x10^6)/(1000x2) = 600.37488 mm > 230 mm RECHECK
Clear cover at liquid face = 25 mm deff provided = 230- 25 - 8- 8/2 = 193 mm
Steel required in liquid face (Vertical) = (120.15 x 10^6) / (190 x 0.89 x 193) = 3681.48 mm2
Provide 8 dia @ 110 c/c = 457 mm 2
(Vertical Reinforcement at Liquid face) INCREASE
Minimum % of reinforcement (HYSD bar) required: 0.21% (in each direction)
Minimum reinforcement required: (0.21) / 100 x 1000 x 230 = 483 mm2 (in each face)
Check for Shear :
Refer Table-11 of IS 3370 Part(IV): For H2/Dt = 143.8 Coeff = 0.127
Maximum shear at base of liquid face : = 0.127 x 115 x 11.5 = 167.96 kN
Shear stress at base of liquid face : = 167.96 x 1000/(193 x 0.89 x 1000)= 0.98 N/mm2
> 0.26 N/mm 2
(Refer Table-80 of SP16) RECHECK
Case - ( Inside empty & Outside full of earth)
Refer Table - 9 of IS 3370 (Part IV):
For H2/Dt = 131.5 Coeff = 0.776 (For triangular load)
Max hoop comp. occures at 0.9 H from top= .536 x 129.4 x 4 / 2= 138.72 kN/m
AATVIK CONSULTANCY INFRASTRUCTURE 50 K.L. Under Ground Sump Well at Salikheda, Sihore (M.P.)
P.H.E.SIHORE (M.P.)
Contractor:- Mettle Infra, Bhopal
Free
11000
Hinged 10000
AATVIK CONSULTANCY INFRASTRUCTURE 50 K.L. Under Ground Sump Well at Salikheda, Sihore (M.P.)
P.H.E.SIHORE (M.P.)
Contractor:- Mettle Infra, Bhopal
From Table - 20 of I.S. 3370 (Part - IV) Max ( - ) Radial Moment coefficient = -0.125 act at 1.00 R
Maximum positive radial moment (Mr)= 0.125 x 66.247 x (4/ 2)^2= 30.25 kN-m/m
From Table - 20 of I.S. 3370 (Part - IV) Max. ( + ) Radial Moment coefficient = 0.075 act at 0.00 R
Maximum negative radial moment (Mr)= 0.075 x 60.5 x (4 / 2)^2= 18.15 kN-m/m
From Table - 20 of I.S. 3370 (Part - IV) Tangential Moment coefficient= 0.075 act at 0.00 R
Maximum Tangential moment (Mt)= 0.075 x 60.5 x (4/2)^2 = 18.15 kN-m/m
Net Moment will be = Ö (Mr +Mt )
2 2
= Ö (30.25^2 + 18.15^2 ) = 35.28 kN-m/m ( at support )
Net Moment will be = Ö (Mr2+Mt2) = Ö (18.15^2 + 18.15^2 ) = 25.67 kN-m/m ( at span )
Clear cover for Base slab : At liquid face = 25 mm At earth face = 35 mm
deff for liquid face reinforcement= 230 - 25 - 10 - 10 /2 = 190 mm
Steel reqd. at liquid face= 25.67 x 10^6 / ( 190 x 0.89 x 190) = 798.97 mm2
Provide 10 dia @ 160 c/c in both directions at liquid face = 490.9 mm2
deff for earth face reinforcement= 230 - 35 - 10 - 10 /2 = 180 mm
Steel reqd. at earth face= 35.28 x 10^6 / ( 190 x 0.904 x 180) = 1141.13 mm2
Provide 10 dia @ 150 c/c in both directions at earth face = 523.6 mm2
Minimum % of reinforcement (TMT bar) required: 0.21% (in each face)
Minimum reinforcement required: (0.21) / 100 x 1000 x 230= 483 mm2 (in each face)
Tension at base due to vertical wall=
Refer Table- 9 of I.S. 3370 (PART- IV) For H2/Dt = 143.8 Coeff near Base (At 0.9 H )= 0.265
Tension will be = 115 x 4/2 x 0.265 = 60.95 kN/m
Checking for uncracked section is required because bending tension is at liquid face.
At span it will be checked by 1 Ö (Radial moment2 + Tangential moment2) = 25.67 kN-m/m
2. Tension for vertical wall's reaction at base. = 60.95 kN/m
Check as Uncracked Section
Section Mark : Base Slab : Bending Tension at span (Liquid face)
M= 25.67 kN-m/m + if tension is at bottom T= 60.95 kN/m
- if tension is at top
Dimensions D= 230 b= 1000 d t' = 50
D= 230 mm A top y top= 115.1
b= 1000 mm
nD
d t' = 50 mm N. A. +M
A top = 5.24 cm 2
T
AATVIK CONSULTANCY INFRASTRUCTURE 50 K.L. Under Ground Sump Well at Salikheda, Sihore (M.P.)
P.H.E.SIHORE (M.P.)
Contractor:- Mettle Infra, Bhopal
230
11000
Plugging
R.C. DETAIL OF RING WALL
10 dia @ 150 c/c at bottom (earth face).
10 dia @ 150 c/c at bottom (earth face).(at support)
10 dia @ 220 c/c at bottom (earth face).(at span)
AATVIK CONSULTANCY INFRASTRUCTURE 50 K.L. Under Ground Sump Well at Salikheda, Sihore (M.P.)
IS : 3370 ( Part IV ) - 1967
Table - 9 TENSION IN CIRCULAR RING WALL, FIXED BASE, FREE TOP AND SUBJECT TO TRIANGULAR LOA
( Clause 3.1.1 )
D
T = Coefficient x w H R kg / m t R
H
w = Density of liquid
Positive sign indicates Tension
wH
H 2 / Dt = 143.8
H2 / D t 0.0 H 0.1 H 0.2 H 0.3 H 0.4 H 0.5 H 0.6 H 0.7 H
0.4 0.149 0.134 0.120 0.101 0.082 0.066 0.049 0.029
0.8 0.263 0.239 0.215 0.109 0.160 0.130 0.096 0.063
1.2 0.283 0.271 0.254 0.234 0.209 0.180 0.142 0.099
1.6 0.265 0.268 0.268 0.266 0.250 0.226 0.185 0.134
2.0 0.234 0.251 0.273 0.285 0.285 0.274 0.232 0.172
3.0 0.134 0.203 0.267 0.322 0.357 0.362 0.330 0.262
4.0 0.067 0.164 0.256 0.339 0.403 0.429 0.409 0.334
5.0 0.025 0.137 0.245 0.346 0.428 0.477 0.469 0.398
6.0 0.018 0.119 0.234 0.344 0.441 0.504 0.514 0.447
8.0 -0.001 0.104 0.218 0.335 0.443 0.534 0.575 0.530
10.0 -0.001 0.098 0.208 0.323 0.437 0.542 0.608 0.589
12.0 -0.005 0.097 0.202 0.312 0.429 0.543 0.628 0.633
14.0 -0.002 0.098 0.200 0.306 0.420 0.539 0.639 0.666
16.0 0.000 0.099 0.199 0.304 0.412 0.531 0.641 0.687
M = Coefficient x w H 3 kgm / m t R
H
w = Density of liquid
Positive sign indicates Tension on the outside
wH
H 2 / Dt = 143.8
H /Dt
2
0.1 H 0.2 H 0.3 H 0.4 H 0.5 H 0.6 H 0.7 H 0.8 H
0.4 0.0005 0.0014 0.0021 0.0007 -0.0042 -0.0150 -0.0302 -0.0529
0.8 0.0011 0.0037 0.0063 0.0080 0.0070 0.0023 -0.0068 -0.0024
1.2 0.0012 0.0042 0.0077 0.0103 0.0112 0.0090 0.0022 -0.0108
1.6 0.0011 0.0041 0.0075 0.0107 0.0121 0.0111 0.0058 -0.0051
2.0 0.0010 0.0035 0.0068 0.0099 0.0120 0.0115 0.0075 -0.0021
3.0 0.0006 0.0024 0.0047 0.0071 0.0090 0.0097 0.0077 0.0012
4.0 0.0003 0.0015 0.0028 0.0047 0.0066 0.0077 0.0069 0.0023
5.0 0.0002 0.0008 0.0016 0.0029 0.0046 0.0059 0.0059 0.0028
6.0 0.0001 0.0003 0.0008 0.0019 0.0032 0.0046 0.0051 0.0029
8.0 0.0000 0.0001 0.0002 0.0008 0.0016 0.0028 0.0038 0.0029
10.0 0.0000 0.0000 0.0001 0.0004 0.0007 0.0019 0.0029 0.0028
12.0 0.0000 -0.0001 0.0001 0.0002 0.0003 0.0013 0.0023 0.0026
14.0 0.0000 0.0000 0.0000 0.0000 0.0001 0.0008 0.0019 0.0023
16.0 0.0000 0.0000 -0.0001 -0.0002 -0.0001 0.0004 0.0013 0.0019
0.8 H 0.9 H
0.014 0.004
0.034 0.010
0.054 0.016
0.075 0.023
0.104 0.031
0.157 0.052
0.210 0.073
0.259 0.092
0.301 0.112
0.381 0.151
0.440 0.179
0.494 0.211
0.541 0.241
0.582 0.265
0.5820 0.2650
0.5820 0.2650
0.5820 0.2650
0.7 H
0.0001 -0.0079
0.0001 -0.0079
0.0001 -0.0079
0.0001 -0.0079
0.0001 -0.0079
IS : 3370 ( Part IV ) - 1967
Table - 11 SHEAR AT BASE OF CYLINICAL WALL
( Clause 3.1.1, 3.1.2 and 3.1.3 )
V = Coefficient x w H 2 kg ( triangular )
p H kg ( rectangular )
M / H kg ( moment at base )
w = Density of liquid
Positive sign indicates Shear acting inward
H 2 / Dt = 143.8
Triangular Rectangular Triangular or Moment
Load Load Rect. Load at
H2 / D t Fixed Base Fixed Base Hinged Base Edge
0.4 0.436 0.755 0.245 -1.58
0.8 0.374 0.552 0.234 -1.75
1.2 0.339 0.460 0.220 -2.00
1.6 0.317 0.407 0.204 -2.28
2.0 0.299 0.370 0.189 -2.57
3.0 0.262 0.310 0.158 -3.18
4.0 0.236 0.271 0.137 -3.68
5.0 0.213 0.243 0.121 -4.10
6.0 0.197 0.222 0.110 -4.49
8.0 0.174 0.193 0.096 -5.18
10.0 0.158 0.172 0.087 -5.81
12.0 0.145 0.158 0.079 -6.38
14.0 0.135 0.147 0.073 -6.88
16.0 0.127 0.137 0.068 -7.36
T = Coefficient x w H R kg / m t R
H
w = Density of liquid
Positive sign indicates Tension
wH
H 2 / Dt = 131.5
H2 / D t 0.0 H 0.1 H 0.2 H 0.3 H 0.4 H 0.5 H 0.6 H 0.7 H
0.4 0.474 0.440 0.395 0.352 0.308 0.264 0.215 0.165
0.8 0.423 0.402 0.381 0.358 0.330 0.297 0.249 0.202
1.2 0.350 0.355 0.361 0.362 0.358 0.342 0.309 0.256
1.6 0.271 0.303 0.341 0.369 0.385 0.385 0.362 0.314
2.0 0.205 0.260 0.321 0.373 0.411 0.434 0.419 0.369
3.0 0.074 0.179 0.281 0.375 0.449 0.506 0.519 0.479
4.0 0.017 0.137 0.253 0.367 0.469 0.545 0.579 0.553
5.0 -0.008 0.114 0.235 0.356 0.469 0.562 0.617 0.606
6.0 -0.011 0.103 0.223 0.343 0.463 0.566 0.639 0.643
8.0 -0.015 0.096 0.208 0.324 0.443 0.564 0.661 0.697
10.0 -0.008 0.095 0.200 0.311 0.428 0.552 0.666 0.730
12.0 -0.002 0.097 0.197 0.302 0.417 0.541 0.664 0.750
14.0 0.000 0.098 0.197 0.299 0.408 0.531 0.659 0.761
16.0 0.002 0.100 0.198 0.299 0.403 0.521 0.650 0.764
M = Coefficient x ( w H 3 + p H 2 ) kgm / m t R
H
w = Density of liquid
Positive sign indicates Tension on the outside
p wH
H 2 / Dt = 131.5
H /Dt
2
0.1 H 0.2 H 0.3 H 0.4 H 0.5 H 0.6 H 0.7 H 0.8 H
0.4 0.0020 0.0072 0.0151 0.0230 0.0301 0.0348 0.0357 0.0312
0.8 0.0019 0.0064 0.0133 0.0207 0.0271 0.0319 0.0329 0.0292
1.2 0.0016 0.0058 0.0111 0.0177 0.0237 0.0280 0.0296 0.0263
1.6 0.0012 0.0044 0.0091 0.0145 0.0195 0.0236 0.0255 0.0232
2.0 0.0009 0.0033 0.0073 0.0114 0.0158 0.0199 0.0219 0.0205
3.0 0.0004 0.0018 0.0040 0.0063 0.0092 0.0127 0.0152 0.0153
4.0 0.0001 0.0007 0.0016 0.0033 0.0057 0.0083 0.0109 0.0118
5.0 0.0000 0.0001 0.0006 0.0016 0.0034 0.0057 0.0080 0.0094
6.0 0.0000 0.0000 0.0002 0.0008 0.0019 0.0039 0.0062 0.0078
8.0 0.0000 0.0000 -0.0002 0.0000 0.0007 0.0020 0.0038 0.0057
10.0 0.0000 0.0000 -0.0002 -0.0001 0.0002 0.0011 0.0025 0.0043
12.0 0.0000 0.0000 -0.0001 -0.0002 0.0000 0.0005 0.0017 0.0032
14.0 0.0000 0.0000 -0.0001 -0.0001 -0.0001 0.0000 0.0012 0.0026
16.0 0.0000 0.0000 0.0000 -0.0001 -0.0002 -0.0004 0.0008 0.0022
0.8 H 0.9 H
0.111 0.057
0.145 0.076
0.186 0.098
0.233 0.124
0.280 0.151
0.375 0.210
0.447 0.256
0.503 0.294
0.547 0.327
0.621 0.386
0.678 0.433
0.720 0.477
0.752 0.513
0.776 0.536
0.7760 0.5360
0.7760 0.5360
0.0029 0.0000
0.0029 0.0000
0.0029 0.0000
IS : 3370 ( Part IV ) - 1967
Table - 14 TENSION IN CIRCULAR RING, HINGED BASE, FREE TOP AND SUBJECT TO
( Clause 3.1.3 ) RECTANGULAR LOAD
D
T = Coefficient x p R kg / m t R
H
16.0 1.0020 1.0000 0.9980 0.9990 1.0030 1.0210 1.0500 1.0640 0.9760
16.0 1.0020 1.0000 0.9980 0.9990 1.0030 1.0210 1.0500 1.0640 0.9760
131.5 1.0020 1.0000 0.9980 0.9990 1.0030 1.0210 1.0500 1.0640 0.9760
0.9 H
0.154
0.166
0.198
0.224
0.251
0.310
0.356
0.394
0.427
0.486
0.533
0.577
0.613
0.636
0.6360
0.6360
0.6360 0.7 H
IS : 3370 ( Part IV ) - 1967
Table - 15 TENSION IN CIRCULAR RING, FIXED BASE, FREE TOP WITH SHEAR 'V'
( Clause 3.1.4 and 3.1.5 ) PER METRE APPLIED AT TOP
V D
T = Coefficient x V R / H kg / m t R
H
H 2 / Dt = 0.3
H2 / D t 0.0 H 0.1 H 0.2 H 0.3 H 0.4 H 0.5 H 0.6 H 0.7 H
0.4 -1.57 -1.32 -1.08 -0.86 -0.65 -0.47 -0.31 -0.18
0.8 -3.09 -2.55 -2.04 -1.57 -1.15 -0.80 -0.51 -0.28
1.2 -3.95 -3.17 -2.44 -1.79 -1.25 -0.81 -0.48 -0.25
1.6 -4.57 -3.54 -2.60 -1.80 -1.17 -0.69 -0.36 -0.16
2.0 -5.12 -3.83 -2.68 -1.74 -1.02 -0.52 -0.21 -0.05
3.0 -6.32 -4.37 -2.70 -1.43 -0.58 -0.02 0.15 0.19
4.0 -7.34 -4.73 -2.60 -1.10 -0.19 0.26 0.38 0.33
5.0 -8.22 -4.99 -2.45 -0.79 0.11 0.47 0.50 0.37
6.0 -9.02 -5.17 -2.27 -0.50 0.34 0.59 0.53 0.35
8.0 -10.42 -5.36 -1.85 -0.02 0.63 0.66 0.46 0.24
10.0 -11.67 -5.43 -1.43 0.36 0.78 0.62 0.33 0.12
12.0 -12.76 -5.41 -1.03 0.63 0.83 0.52 0.21 0.04
14.0 -13.77 -5.34 -0.68 0.80 0.81 0.42 0.13 0.00
16.0 -14.74 -5.22 -0.33 0.96 0.76 0.32 0.05 -0.04
* When this table is used for shear applied at the base, while the top is fixed, 0.0 H is the bottom
of the wall and 1.0 H is the top. Shear acting inward is positive, outward is negative.
V
0.8 H 0.9 H
-0.08 -0.02
-0.13 -0.03
-0.10 -0.02
-0.05 -0.01
0.01 0.01
0.13 0.04
0.19 0.06
0.20 0.06
0.17 0.01
0.09 0.01
0.02 0.00
-0.02 0.00
-0.03 -0.01
-0.05 -0.02
-0.0800 -0.0200
-0.0800 -0.0200
-0.0800 -0.0200
T = Coefficient x M R / H 2 kg / m t R
H
* When this table is used for moment applied at the top, while the top is hinged, 0.0 H is the bottom of the
wall and 1.0 H is the top. Moment applied at an edge is positive wfen it causes outward rotation at that edge.
M = Coefficient x M kgm / m t R
H
Positive sign indicates Tension in outside
M M
H / Dt =
2
0.3
H2 / D t 0.1 H 0.2 H 0.3 H 0.4 H 0.5 H 0.6 H 0.7 H 0.8 H
0.4 0.013 0.051 0.109 0.196 0.296 0.414 0.547 0.692
0.8 0.009 0.040 0.090 0.164 0.253 0.375 0.503 0.659
1.2 0.006 0.027 0.063 0.125 0.206 0.316 0.454 0.616
1.6 0.003 0.011 0.035 0.078 0.152 0.253 0.393 0.570
2.0 -0.002 -0.002 0.012 0.034 0.096 0.193 0.340 0.519
3.0 -0.007 -0.022 -0.030 -0.029 0.010 0.087 0.227 0.426
4.0 -0.008 -0.026 -0.044 -0.051 -0.034 0.023 0.150 0.354
5.0 -0.007 -0.024 -0.045 -0.061 -0.057 -0.015 0.095 0.296
6.0 -0.005 -0.018 -0.040 -0.058 -0.065 -0.037 0.057 0.252
8.0 -0.001 -0.009 -0.022 -0.044 -0.068 -0.062 0.002 0.178
10.0 0.000 -0.002 -0.009 -0.028 -0.053 -0.067 -0.031 0.123
12.0 0.000 0.000 -0.003 -0.016 -0.040 -0.064 -0.049 0.081
14.0 0.000 0.000 0.000 -0.008 -0.029 -0.059 -0.060 0.048
16.0 0.000 0.000 0.002 -0.003 -0.021 -0.051 -0.066 0.025
* When this table is used for moment applied at the top, while the top is hinged, 0.0 H is the bottom of the
wall and 1.0 H is the top. Moment applied at an edge is positive wfen it causes outward rotation at that edge.
TH MOMENT PER METRE,
0.8 H 0.9 H
0.80 0.44
1.39 0.80
2.22 1.37
3.13 2.01
4.08 2.75
6.58 4.73
8.82 6.81
11.03 9.02
13.08 11.41
16.52 16.06
19.48 20.87
21.80 25.73
23.50 30.34
24.53 34.65
0.8000 0.4400
0.8000 0.4400
0.8000 0.4400
0.8430 1.0000
0.8430 1.0000
0.8430 1.0000
M = Coefficient x p H 2 kgm / m t R
H
M = Coefficient x V H kgm / m t R
H
* When this table is used for shear applied at the base, while the top is fixed, 0.0 H is the bottom
of the wall and 1.0 H is the top. Shear acting inward is positive, outward is negative.
SUBJECT TO RECTANGULAR LOAD
0.9 H 1.0 H
-0.2593 -0.3310
-0.1325 -0.1835
-0.0815 -0.1178
-0.0529 -0.0876
-0.0389 -0.0719
-0.0223 -0.0483
-0.0145 -0.0365
-0.0101 -0.0293
-0.0073 -0.0242
-0.0040 -0.0184
-0.0022 -0.0147
-0.0012 -0.0123
-0.0007 -0.0105
-0.0005 -0.0091
-0.0005 -0.0091
-0.0005 -0.0091
V
0.9 H 1.0 H
0.535 0.578
0.214 0.208
0.084 0.062
0.030 0.004
0.006 -0.019
-0.010 -0.024
-0.010 -0.019
-0.007 -0.011
-0.005 -0.006
-0.002 -0.001
-0.001 0.000
0.000 0.000
0.000 0.000
0.000 0.000
0.5350 0.5780
0.5350 0.5780
0.5350 0.5780
T = Coefficient x w H R kg / m t R
H
w = Density of liquid
Positive sign indicates Tension
wH
H 2 / Dt = 131.5
H2 / D t 0.0 H 0.1 H 0.2 H 0.3 H 0.4 H 0.5 H 0.6 H 0.7 H
0.4 0.149 0.134 0.120 0.101 0.082 0.066 0.049 0.029
0.8 0.263 0.239 0.215 0.109 0.160 0.130 0.096 0.063
1.2 0.283 0.271 0.254 0.234 0.209 0.180 0.142 0.099
1.6 0.265 0.268 0.268 0.266 0.250 0.226 0.185 0.134
2.0 0.234 0.251 0.273 0.285 0.285 0.274 0.232 0.172
3.0 0.134 0.203 0.267 0.322 0.357 0.362 0.330 0.262
4.0 0.067 0.164 0.256 0.339 0.403 0.429 0.409 0.334
5.0 0.025 0.137 0.245 0.346 0.428 0.477 0.469 0.398
6.0 0.018 0.119 0.234 0.344 0.441 0.504 0.514 0.447
8.0 -0.001 0.104 0.218 0.335 0.443 0.534 0.575 0.530
10.0 -0.001 0.098 0.208 0.323 0.437 0.542 0.608 0.589
12.0 -0.005 0.097 0.202 0.312 0.429 0.543 0.628 0.633
14.0 -0.002 0.098 0.200 0.306 0.420 0.539 0.639 0.666
16.0 0.000 0.099 0.199 0.304 0.412 0.531 0.641 0.687
M = Coefficient x w H 3 kgm / m t R
H
w = Density of liquid
Positive sign indicates Tension on the outside
wH
H 2 / Dt = 131.50
H /Dt
2
0.1 H 0.2 H 0.3 H 0.4 H 0.5 H 0.6 H 0.7 H 0.8 H
0.4 0.0005 0.0014 0.0021 0.0007 -0.0042 -0.0150 -0.0302 -0.0529
0.8 0.0011 0.0037 0.0063 0.0080 0.0070 0.0023 -0.0068 -0.0024
1.2 0.0012 0.0042 0.0077 0.0103 0.0112 0.0090 0.0022 -0.0108
1.6 0.0011 0.0041 0.0075 0.0107 0.0121 0.0111 0.0058 -0.0051
2.0 0.0010 0.0035 0.0068 0.0099 0.0120 0.0115 0.0075 -0.0021
3.0 0.0006 0.0024 0.0047 0.0071 0.0090 0.0097 0.0077 0.0012
4.0 0.0003 0.0015 0.0028 0.0047 0.0066 0.0077 0.0069 0.0023
5.0 0.0002 0.0008 0.0016 0.0029 0.0046 0.0059 0.0059 0.0028
6.0 0.0001 0.0003 0.0008 0.0019 0.0032 0.0046 0.0051 0.0029
8.0 0.0000 0.0001 0.0002 0.0008 0.0016 0.0028 0.0038 0.0029
10.0 0.0000 0.0000 0.0001 0.0004 0.0007 0.0019 0.0029 0.0028
12.0 0.0000 -0.0001 0.0001 0.0002 0.0003 0.0013 0.0023 0.0026
14.0 0.0000 0.0000 0.0000 0.0000 0.0001 0.0008 0.0019 0.0023
16.0 0.0000 0.0000 -0.0001 -0.0002 -0.0001 0.0004 0.0013 0.0019
0.8 H 0.9 H
0.014 0.004
0.034 0.010
0.054 0.016
0.075 0.023
0.104 0.031
0.157 0.052
0.210 0.073
0.259 0.092
0.301 0.112
0.381 0.151
0.440 0.179
0.494 0.211
0.541 0.241
0.582 0.265
0.5820 0.2650
0.5820 0.2650
0.0001 -0.0079
0.0001 -0.0079
T = Coefficient x w H R kg / m t R
H
w = Density of liquid
Positive sign indicates Tension
wH
H 2 / Dt = 0.3
H2 / D t 0.0 H 0.1 H 0.2 H 0.3 H 0.4 H 0.5 H 0.6 H 0.7 H
0.4 0.149 0.134 0.120 0.101 0.082 0.066 0.049 0.029
0.8 0.263 0.239 0.215 0.109 0.160 0.130 0.096 0.063
1.2 0.283 0.271 0.254 0.234 0.209 0.180 0.142 0.099
1.6 0.265 0.268 0.268 0.266 0.250 0.226 0.185 0.134
2.0 0.234 0.251 0.273 0.285 0.285 0.274 0.232 0.172
3.0 0.134 0.203 0.267 0.322 0.357 0.362 0.330 0.262
4.0 0.067 0.164 0.256 0.339 0.403 0.429 0.409 0.334
5.0 0.025 0.137 0.245 0.346 0.428 0.477 0.469 0.398
6.0 0.018 0.119 0.234 0.344 0.441 0.504 0.514 0.447
8.0 -0.001 0.104 0.218 0.335 0.443 0.534 0.575 0.530
10.0 -0.001 0.098 0.208 0.323 0.437 0.542 0.608 0.589
12.0 -0.005 0.097 0.202 0.312 0.429 0.543 0.628 0.633
14.0 -0.002 0.098 0.200 0.306 0.420 0.539 0.639 0.666
16.0 0.000 0.099 0.199 0.304 0.412 0.531 0.641 0.687
M = Coefficient x w H 3 kgm / m t R
H
w = Density of liquid
Positive sign indicates Tension on the outside
wH
H 2 / Dt = 0.3
H /Dt
2
0.1 H 0.2 H 0.3 H 0.4 H 0.5 H 0.6 H 0.7 H 0.8 H
0.4 0.0005 0.0014 0.0021 0.0007 -0.0042 -0.0150 -0.0302 -0.0529
0.8 0.0011 0.0037 0.0063 0.0080 0.0070 0.0023 -0.0068 -0.0024
1.2 0.0012 0.0042 0.0077 0.0103 0.0112 0.0090 0.0022 -0.0108
1.6 0.0011 0.0041 0.0075 0.0107 0.0121 0.0111 0.0058 -0.0051
2.0 0.0010 0.0035 0.0068 0.0099 0.0120 0.0115 0.0075 -0.0021
3.0 0.0006 0.0024 0.0047 0.0071 0.0090 0.0097 0.0077 0.0012
4.0 0.0003 0.0015 0.0028 0.0047 0.0066 0.0077 0.0069 0.0023
5.0 0.0002 0.0008 0.0016 0.0029 0.0046 0.0059 0.0059 0.0028
6.0 0.0001 0.0003 0.0008 0.0019 0.0032 0.0046 0.0051 0.0029
8.0 0.0000 0.0001 0.0002 0.0008 0.0016 0.0028 0.0038 0.0029
10.0 0.0000 0.0000 0.0001 0.0004 0.0007 0.0019 0.0029 0.0028
12.0 0.0000 -0.0001 0.0001 0.0002 0.0003 0.0013 0.0023 0.0026
14.0 0.0000 0.0000 0.0000 0.0000 0.0001 0.0008 0.0019 0.0023
16.0 0.0000 0.0000 -0.0001 -0.0002 -0.0001 0.0004 0.0013 0.0019
0.8 H 0.9 H
0.014 0.004
0.034 0.010
0.054 0.016
0.075 0.023
0.104 0.031
0.157 0.052
0.210 0.073
0.259 0.092
0.301 0.112
0.381 0.151
0.440 0.179
0.494 0.211
0.541 0.241
0.582 0.265
0.0140 0.0040
0.0140 0.0040
-0.0816 -0.1205
-0.0816 -0.1205
-0.0816 -0.1205
IS : 3370 ( Part IV ) - 1967
Table - 9 TENSION IN CIRCULAR RING WALL, FIXED BASE, FREE TOP AND SUBJECT TO TRIANGULAR LOA
( Clause 3.1.1 )
D
T = Coefficient x w H R kg / m t R
H
w = Density of liquid
Positive sign indicates Tension
wH
H 2 / Dt = 0.3
H2 / D t 0.0 H 0.1 H 0.2 H 0.3 H 0.4 H 0.5 H 0.6 H 0.7 H
0.4 0.149 0.134 0.120 0.101 0.082 0.066 0.049 0.029
0.8 0.263 0.239 0.215 0.109 0.160 0.130 0.096 0.063
1.2 0.283 0.271 0.254 0.234 0.209 0.180 0.142 0.099
1.6 0.265 0.268 0.268 0.266 0.250 0.226 0.185 0.134
2.0 0.234 0.251 0.273 0.285 0.285 0.274 0.232 0.172
3.0 0.134 0.203 0.267 0.322 0.357 0.362 0.330 0.262
4.0 0.067 0.164 0.256 0.339 0.403 0.429 0.409 0.334
5.0 0.025 0.137 0.245 0.346 0.428 0.477 0.469 0.398
6.0 0.018 0.119 0.234 0.344 0.441 0.504 0.514 0.447
8.0 -0.001 0.104 0.218 0.335 0.443 0.534 0.575 0.530
10.0 -0.001 0.098 0.208 0.323 0.437 0.542 0.608 0.589
12.0 -0.005 0.097 0.202 0.312 0.429 0.543 0.628 0.633
14.0 -0.002 0.098 0.200 0.306 0.420 0.539 0.639 0.666
16.0 0.000 0.099 0.199 0.304 0.412 0.531 0.641 0.687
M = Coefficient x w H 3 kgm / m t R
H
w = Density of liquid
Positive sign indicates Tension on the outside
wH
H 2 / Dt = 0.3
H /Dt
2
0.1 H 0.2 H 0.3 H 0.4 H 0.5 H 0.6 H 0.7 H 0.8 H
0.4 0.0005 0.0014 0.0021 0.0007 -0.0042 -0.0150 -0.0302 -0.0529
0.8 0.0011 0.0037 0.0063 0.0080 0.0070 0.0023 -0.0068 -0.0024
1.2 0.0012 0.0042 0.0077 0.0103 0.0112 0.0090 0.0022 -0.0108
1.6 0.0011 0.0041 0.0075 0.0107 0.0121 0.0111 0.0058 -0.0051
2.0 0.0010 0.0035 0.0068 0.0099 0.0120 0.0115 0.0075 -0.0021
3.0 0.0006 0.0024 0.0047 0.0071 0.0090 0.0097 0.0077 0.0012
4.0 0.0003 0.0015 0.0028 0.0047 0.0066 0.0077 0.0069 0.0023
5.0 0.0002 0.0008 0.0016 0.0029 0.0046 0.0059 0.0059 0.0028
6.0 0.0001 0.0003 0.0008 0.0019 0.0032 0.0046 0.0051 0.0029
8.0 0.0000 0.0001 0.0002 0.0008 0.0016 0.0028 0.0038 0.0029
10.0 0.0000 0.0000 0.0001 0.0004 0.0007 0.0019 0.0029 0.0028
12.0 0.0000 -0.0001 0.0001 0.0002 0.0003 0.0013 0.0023 0.0026
14.0 0.0000 0.0000 0.0000 0.0000 0.0001 0.0008 0.0019 0.0023
16.0 0.0000 0.0000 -0.0001 -0.0002 -0.0001 0.0004 0.0013 0.0019
0.8 H 0.9 H
0.014 0.004
0.034 0.010
0.054 0.016
0.075 0.023
0.104 0.031
0.157 0.052
0.210 0.073
0.259 0.092
0.301 0.112
0.381 0.151
0.440 0.179
0.494 0.211
0.541 0.241
0.582 0.265
0.0140 0.0040
0.0140 0.0040
-0.0816 -0.1205
-0.0816 -0.1205
-0.0816 -0.1205
IS : 3370 ( Part IV ) - 1967
Table - 11 SHEAR AT BASE OF CYLINICAL WALL
( Clause 3.1.1, 3.1.2 and 3.1.3 )
V = Coefficient x w H 2 kg ( triangular )
p H kg ( rectangular )
M / H kg ( moment at base )
w = Density of liquid
Positive sign indicates Shear acting inward
H 2 / Dt = 131.5
Triangular Rectangular Triangular or Moment
Load Load Rect. Load at
H2 / D t Fixed Base Fixed Base Hinged Base Edge
0.4 0.436 0.755 0.245 -1.58
0.8 0.374 0.552 0.234 -1.75
1.2 0.339 0.460 0.220 -2.00
1.6 0.317 0.407 0.204 -2.28
2.0 0.299 0.370 0.189 -2.57
3.0 0.262 0.310 0.158 -3.18
4.0 0.236 0.271 0.137 -3.68
5.0 0.213 0.243 0.121 -4.10
6.0 0.197 0.222 0.110 -4.49
8.0 0.174 0.193 0.096 -5.18
10.0 0.158 0.172 0.087 -5.81
12.0 0.145 0.158 0.079 -6.38
14.0 0.135 0.147 0.073 -6.88
16.0 0.127 0.137 0.068 -7.36
V = Coefficient x w H 2 kg ( triangular )
p H kg ( rectangular )
M / H kg ( moment at base )
w = Density of liquid
Positive sign indicates Shear acting inward
H 2 / Dt = 0.3
Triangular Rectangular Triangular or Moment
Load Load Rect. Load at
H2 / D t Fixed Base Fixed Base Hinged Base Edge
0.4 0.436 0.755 0.245 -1.58
0.8 0.374 0.552 0.234 -1.75
1.2 0.339 0.460 0.220 -2.00
1.6 0.317 0.407 0.204 -2.28
2.0 0.299 0.370 0.189 -2.57
3.0 0.262 0.310 0.158 -3.18
4.0 0.236 0.271 0.137 -3.68
5.0 0.213 0.243 0.121 -4.10
6.0 0.197 0.222 0.110 -4.49
8.0 0.174 0.193 0.096 -5.18
10.0 0.158 0.172 0.087 -5.81
12.0 0.145 0.158 0.079 -6.38
14.0 0.135 0.147 0.073 -6.88
16.0 0.127 0.137 0.068 -7.36
M = Coefficient x p R 2 kgm / m