Professional Documents
Culture Documents
MT4W SERIES
Power supply 100 240VAC 50/60Hz I12 24VDC at moment of power on. All outputs are off during startup compensation time setting after power is supplied.
Allowable voltage range 90 to 110% Setting range: 00.0 to 99.9 (unit: sec), Factory default: 00.0
▣ Parameter
Power consumption 5VA I5W
INSTRUCTION MANUAL
Display method 7 Segment LED display (red (Character height: 14.2mm
23℃±5℃ DC Type: F.S.±0.1% rdg±2digit / AC Type: F.S.±0.3% rdg±3digit Parameter Display Function Note
Display accuracy DC/AC Type: F.S.+0.3% rdg +3digit max. only for 5A terminal Input type Selectable RMS/AVG in AC type Available AC type only.
10℃ to 50℃ DC/AC Type: F.S.±0.5% rdg±3digit
N-T
Input range Selection of input range
Input DC Voltage/Current, AC Voltage/Current, AC Frequency
N-R
Display Selection of display type Setting range: STND, SCAL, FREQ
Max. allowable input 110% for each measured input range D SP
A/D conversion method ΣΔ (Sigma Delta ADC STND Standard Standard scale range Display Max. display value of STND
Sampling cycle DC type: 50ms, AC type: 16.6ms FREQ Frequency Frequency display Available AC type only.
Max. indication range 1999 to 9999 (4digit) SCAL Scale Scale range These are displayed at SCAL
• Relay output Contact capacity: 250VAC 3A, 30VDC 3A/Contact composition: N.O (1a) High scale Set max. value of display range It sets max. display value/min. display
Preset output value ( 1999 to 9999)
H-SC
• NPN/PNP Open Collector output 12 24VDC ±2V 50mA Max. (Load resistance) Low scale Set min. value of display range
PA1
(Parameter1) L-SC
• RS485 communication output Baud rate:1200/2400/4800/9600, Communication method : 2 wire It is dispayed at SCAL /FREQ only and set
Sub output DOT Dot Set decimal point position the decimal point position
half duplex,Synchronous method: Asynchronous method , Protocol : Modbus type
(Transmission
Thank you or choos ng our Auton cs products output)
• Serial/BCD output NPN Open collector output, 12 24VDC Max. 50mA (Resistive load) Correct High limit value
NbH Input bias high of display value STND/ SCAL: Correction range 0.100 to 5.000
FREQ: Correction range 0.100 to 9.999
Please read the following safety considerations before use.
• DC4 20mA output Resolution: 12,000 division (Load resistance max. 600Ω), Response time:Max. 450ms
Insulation resistance Over 100MΩ (at 500VDC megger between external terminal and case Correct Low limit value
NbL Input bias low of display value Setting range: 99 to +99
Dielectric stength 2,000VAC for 1minute between external terminal and case
▣ Safety Considerations
Input bias Set display index of
Noise immunity ±2kV the square wave noise (pulse width: 1㎲) by the noise simulator Setting range: 10 2, 10 , 10 , 10
NbE exponent frequency mode
Mechanical 0.75mm amplitude at frequency of 10 to 55Hz (for 1 min) in each X, Y, Z direction for 2 hours
Vibration Set operation mode of Setting range: OFF, lST, hST, LhST,
※‘Please observe all safety considerations for safe and proper product operation to avoid hazards Malfunction 0.5mm amplitude at frequency of 10 to 55Hz (for 1 min in each X, Y, Z direction for 10 min OUtT Out type preset output
Mechanical 100m/s² (approx. 10G in each X, Y, Z direction for 3 times
HhST, LlST, LdST
※ symbol represents caution due to special circumstances in which hazards may occur Shock HYS Hysteresis Set hysteresis value Setting range: 1 to 10% F.S.
Malfunction 300m/s² (approx. 30G) in each X, Y, Z direction for 3 times Startup compen
Warning Failure to follow these instructions may result in serious injury or death Relay Mechanical Min. 20,000,000 operations STaT sation time Set startup compensation time. Setting range: 00 to 99.9sec
life cycle Malfunction Min. 100,000 operations (250VAC 3A Load current) Set monitoring delay time
Caution Failure to follow these instructions may result in personal injury or product damage. Ambient PEkT Peak time for peak value (sec
Setting range: 00 to 30sec
10 to 50℃, Storage: 20 to 60℃
Environ temperature Setting range: 0.1 to 5.0 sec
Warning ment Ambient D sT Display time Set sampling time (sec) (Variable by 0.1sec)
35 to 85%RH, Storage: 35 to 85%RH
1. Fail-safe device must be installed when using the unit with machinery that may cause serious injury or humidity Set usage of front side zero NO: Not use front side zero adjustment key
Double insulation or reinforced insulation ZERO Zero Key adjustment key YES: Use front side zero adjustment key
substantial economic loss. (e.g. nuclear power control, medical equipment, ships, vehicles, railways, Insulation type
PA2
(Parameter2)
aircraft, combustion apparatus, safety equipment, crime/disaster prevention devices, etc.) (Mark: IQ] , dielectric strength between the measuring input part and the power part: 1kV) HOLD: Use external terminal as Hold terminal
Set external terminal (6, 7)
Failure to follow this instruction may result in personal injury, economic loss or fire. Approval ᜢ ᜧ Iᜢ EV N Event Input function
ZERO: Use external terminal as zero point
2. Do not use the unit in the place where flammable/explosive/corrosive gas, high humidity, direct adjustment terminal
Weight※ Approx. 326g (approx. 211g
sunlight, radiant heat, vibration, impact, or salinity may be present. Set the upper value output
※1: The weight includes packaging. The weight in parenthesis is for unit only. FS-H Full scale High point or PV output Min. set range: Min. 10% F.S.
Failure to follow this instruction may result in explosion or fire.
3. Install on a device panel to use. ※ Environment resistance is rated at no freezing or condensation. Set the lower value output
FS-L Full scale Low point or PV output Max. set range: Max. FS H 10%
▣ Measurement Input [PA 1: IN-R]
Failure to follow this instruction may result in fire or electric shock.
4. Do not connect, repair, or inspect the unit while connected to a power source. ADRS Address Set communication address Setting range: 01 to 99
Failure to follow this instruction may result in fire or electric shock. Bit per second Set baudrate (bps) Setting range: 1200, 2400, 4800, 9600
5. Check 'Connections' before wiring. Measured input Input BPS
Type Display range [STND] Prescale Display range [SCAL] Lock Set lock function Setting range: OFF, LOC1, LOC2, LOC3
Failure to follow this instruction may result in fire. and range impedance LOC
6. Do not disassemble or modify the unit. 0 500V [ 500V] 4.33348MΩ 0.0 to 500.0 (fixed) hSET High set Set High setting value Setting range can be set within the
Failure to follow this instruction may result in fire or electric shock. 0 100V [100V] 4.33348MΩ 0.0 to 100.0 (fixed) PA 0 Low set Set Low setting value display range of STND/ SCAL
DOT Display range
lSET
(Parameter0)
Caution High peak Max. value by data monitoring Initializes the monitored data value by
~
0 50V [ 50V] 433.48㏀ 0.00 to 50.00 (fixed) hPEK
I 0 1999 to 9999 Low peak Min. value by data monitoring pressing any one of ll\]ll1]1l§] keys.
0 10V [10V] 433.48㏀ 0.00 to 10.00 (fixed)
1. W
hen connecting the power/measurement input and relay output, use AWG 24(0.20mm2) to AWG
▣ Parameter Setting ▣ Parameter 0
DC Volt
lPEK
0 5V 43.48㏀ 0.000 to 5.000 (fixed )0 199.9 to 999.9
15(1.65mm2) cable and tighten the terminal screw with a tightening torque of 0.98 to 1.18N.m. 5V
Use proper cables for the rated load current. 0 1V [1V] 43.48㏀ 0.000 to 1.000 (fixed) )00 19.99 to 99.99
Failure to follow this instruction may result in fire or malfunction due to contact failure. 0 250mV [ )25V] 2.28㏀ 0.0 to 250.0 (fixed) )000 1.999 to 9.999 RUN ※Press 1ml key in RUN mode and it
enters PA 0 group. RUN
2. Use the unit within the rated specifications. 0 50mV [ 50MV] 2.28㏀ 0.00 to 50.00 (fixed) key sec
(Display range is variable ※Press 1ml key for over 3 sec in RUN
key
Failure to follow this instruction may result in fire or product damage. key touch
3. Use dry cloth to clean the unit, and do not use water or organic solvent. 0 5A [ 5A] 0.022Ω 0.000 to 5.000 (fixed) according to decimal point key sec
mode, it displays [PA1]. Set preset High limit value. (It is not displayed
Failure to follow this instruction may result in fire or electric shock.
4. Keep the product away from metal chip, dust, and wire residue which flow into the unit.
Failure to follow this instruction may result in fire or product damage. DC
0 2A
0 500mA
0 200mA
[ 2A]
[ )5A]
[ )2A]
0.022Ω
0.222Ω
0.222Ω
0.000 to 2.000 (fixed)
0.0 to 500.0 (fixed)
0.0 to 200.0 (fixed)
position.)
PA2
key 2 sec
key sec
※Press 1ml key for over 5 sec in RUN
mode, it displays [PA2] after [PA1].
When pressing key continually,
it stops displaying at [PA2].
ct~hSET when OUtT mode value of PA2 is OFF)
※Change the value with keys.
Set preset Low limit value. (It is not displayed
lSET when OUtT mode value of PA2 is OFF)
▣ Front Panel Identification ▣ Panel Cut-Out
Ampere 0 50mA [ 50MA] 2.222Ω 0.00 to 50.00 (fixed) ※It is advanced to current display parameter releasing ※Change the value with keys.
4 20mA [ 4 20] 2.222Ω 4.00 to 20.00 (fixed) whose 30% to 100% of the input J~
key at [PA1] or [PA2]. It displays High limit monitoring
range includs the max. value of the ※Press key for over 3 sec in any parameter groups, it
(Unit:mm) 0 5mA [ 5MA] 22.222Ω 0.000 to 5.000 (fixed) value (High peak) in RUN mode.
1. HI: High output indication of preset input range to measure.
1
2
2 GO: GO output indication of preset
6 3 LO: Low output indication of preset
Min. 116
45
0 2mA
0 500V
0 250V
[ 2MA]
[ 500V]
[ 250V]
22.222Ω
5.01092MΩ
5.01092MΩ
0.000 to 2.000 (fixed)
0.0 to 500.0 (fixed)
0.0 to 250.0 (fixed)
When the max. input value is
under the 30% of the input
returns to RUN mode.
※If any key is not entered for 60 sec in each parameter, it
returns to RUN mode.
※After returning to RUN mode, press !lQii!,] key within 2
::]~~~@§]
hPEK
It is initialized by pressing any one of
-----: Itvalue
keys.
displays High limit monitoring
3
4 5
4.
5.
: MODE Key
Control key
6. Unit label part
※There are no 1, 2, 3 output
Min. 52.0
92 8
6
AC Volt
0 110V
0 50V
0 20V
[110P]
[ 50V]
[ 20V]
1.11092MΩ
1.11092MΩ
200.92㏀
0.0 to 440.0 (fixed)
0.00 to 50.00 (fixed)
0.00 to 20.00 (fixed)
terminal range, display accuracy is
degraded.
When the max. input value is over
the 100%, it may result in input
sec, it returns to previous parameter. (Refer to the below
descriptions of each parameter group.)
※PA 0 group cannot be entered when preset output mode
. . . ·~~~@§]
: lPEK (Low peak) in RUN mode.
It is initialized by pressing any one of
keys.
※If PEK T of Parameter2 is set as '00 S',
of [PA2] group is OFF. hPEK and lPEK are not displayed.
indication in Indication type. 0 10V [10V] 200.92㏀ 0.00 to 10.00 (fixed) terminal damage.
▣ Connections
0 2V
0 1V
[ 2V]
[1V]
20.92㏀
20.92㏀
0.000 to 2.000 (fixed)
0.000 to 1.000 (fixed)
▣ Parameter 1
※In case of 0 to 110V [110P] RUN Item Range of measured input
※Use teminals of size specified below. 0 5A [ 5A] 0.02Ω 0.000 to 5.000 (fixed) of AC voltage range and using
※Use the Copper conductor wire with the temperature class 60℃. 0 2.5A [ @5A] 0.02Ω 0.000 to 2.500 (fixed) key for 3 sec MT4W DV 500V
P.T (potential transformer) for
00V 50V 0V 5V V )25V 50MV 500V
a b 0 1A [1A] 0.102Ω 0.000 to 1.000 (fixed) 440V/110VAC, if 110V is input, MT4W DA 5A 2A )5A )2A 50MA 4 20 5MA 2MA 5A
AC
1~111
PA1
0 500mA [ )5A] 0.202Ω 0.0 to 500.0 (fixed) and the unit displays 440V MT4W AV
a b Min. Max. Ampere Select measured input specification.
500V 250V 0P(※) 50V 20V 0V 2V V 500V
0 250mA [ )25A] 0.202Ω 0.0 to 250.0 (fixed) automatically by preset scale MT4W AA 5A @5A
3.5mm 7.0mm value for P.T user's convenient. Refer to " Measurement Input".
a N-R A )5A )25A ) A 50MA 5A
<Forked> 0 100mA [ )1A] 1.022Ω 0.0 to 100.0 (fixed) 0P is standard specification of 440/110P. .
<Input> 0 50mA [ 50MA] 1.022Ω 0.00 to 50.00 (fixed) Select the display method of measuring input.
※When "HHHH" or "LLLL" is flashes with a certain measurement input, disconnect power supply and then check the cables. Setting range: STND, SCAL, FREQ.
● MT4W-DV-□□ ※
● MT4W-DA-□□ ※ D SP
Refer to "00 Measurement Input". (FREQ mode is only for AC measuring type.)
ID D D D D D D D DI
1 2 3 4 5 6 7 8 9
ID DD DD DD D DI
1 2 3 4 5 6 7 8 9 ▣ Display Cycle Delay Function [PA 2 : DIsT] Select measurement method when it is AC input.
ll : 250mVDC /50mVDC
5VDC /1VDC
50VDC /10VDC
500VDC /100VDC
I A l-J ffi &
COM
HOLD/
ZERO
+ -
SOURCE
12-24VDC 5W
100-240VACᜠ
~l
5A/2A
J
5mA/2mA
50mA/4-20mA
500mA/200mA
COM
L-J
HOLD/
ZERO
ffi&+ -
SOURCE
12-24VDC 5W
100-240VACᜠ
In some applications the measured input may fluctuate which in turn causes the display to fluctuate.
By adjusting the display cycle delay function time at DIS T of parameter 2, the operator can adjust the display time
within a range of 0.1 sec to 5 sec. For example, if the operator sets the display cycle time to 4.0 sec,
the display value displayed will be the average input value over 4 sec and also will show any changes if any every 4 sec.
N-T
Setting range: AUG, RMS (Average: AVG/Root mean square: RMS)
r
50/60Hz 5VA 50/60Hz 5VA value of standard DOT Setting range: DOT (Refer to "00 AC Frequency
● MT4W-AV-□□ ● MT4W-AA-□□
※ ※
STND
specification. ] ~ 0, )0, )00, )000 Measurement Function Part".)
Display Value Function
...
Display value is fixed. Set display value for max.
ID DD DD DD D DI
1 2 3 4 5 6 7 8 9
ID DD DD DD D DI
1 2 3 4 5 6 7 8 9
[PA 0: hPEK/lPEK,PA 2: PEkT]
This function is to initialize parameter as factory difault. H-SC input of measured input
~~·
2VACᜠ/1VACᜠ
20VACᜠ/10VACᜠ
110VACᜠ/50VACᜠ
500VACᜠ/250VACᜠ
COM
J HOLD/
GJ
ZERO
+ -
ffi&
SOURCE
12-24VDC 5W
100-240VACᜠ
l~ d 100mA/50mA
500mA/250mA
1A
5A/2.5A
COM
HOLD/
w ®&
ZERO
+ -
SOURCE
12-24VDC 5W
100-240VACᜠ
50/60Hz 5VA
It monitors Max./Min. display value based on the current
displays value and then displays the data at hPEK, lPEK
of parameter 0. Set the delay time (0 to 30 sec) at PEkT
RUN
Press for over 5 sec
l~ Set display value for min.
L-SC input of measured inputc
5A RUN mode.
10 11 12 13 14 15 10 11 12 13 14 15 ※Monitoring function is not displayed when the delay time
.~
(NPN OPEN COLLEC OR Collector) (NPN OPEN COLLEC OR Collector) The devication value is saved at INbL automatically.
12-24VDC Max. 50mA 12-24VDC 12-24VDC Max. 50mA 12-24VDC
[PA 1 : INbH/ INbL] Press one
N-R 250V
It adjusts the indication value of the optioanl Select either Hold input by No.6, 7 terminal or zero
125V
Max. 50mA Max. 50mA
COM1 HI LO 0V COM2 DA A COM1 HI LO 0V COM2 DA A configured input value as zero by force, zero point point setting by external signal.
1 3 5 7 9 11 13 15 17 19
It corrects display value error of measured input. EV N
HOLD: Display value holding, ZERO: Zero point
1 3 5 7 9 11 13 15 17 19 error can be adjusted with 3 ways as below.
INB L: ±99 [Adjust deviation of low value] ]~ adjustment by hold terminal.
● NPN Open Collector output+RS485 output[8] ● PNP open collector output+RS485 output[9] INB H: 5.000 to 0.100 [Correct gradient (%) of high value] When zero point adjustment with front key and
Hold terminal is finished normally, zero point Set high limit value for DC 20mA output position of PV putput. D SP
Diplay value= (Measured value INB H) + INB L FS-H ※When changing input range and prescale mode, the setting 5. When confitming the setting value with
2 4 6 8 10 12 14 16 18 20 2 4 6 8 10 12 14 16 18 20 of measurement terminal is displayed and the
When the measured range is 0 to 500V, and the display values of FS H, FS L are changed automatically as max.
key, the changed setting value flashes
+24VDC B (- SG Main Out +24VDC B (- SG Main Out adjusted value is saved at INbL automatically. and min. value of input range.
GO 30mA Max. (NPN Open GO 30mA Max. (PNP Open range is 0 to 500.0. If the low display value is "1 2" to twice and enters into the next setting.
RS485 0V input, set 12 as the INbL value to display "0 0" by Input correc Input external FS-L Set low limit value for 4mA output position of PV output.
RS485 Collector) Collector) Operation Front side key
tion value signal
12-24VDC 12-24VDC adjusting the offset of the low value. 6. It returns RUN mode from parameter by
COM1 HI LO
1 3 5
0V A (+ SG
7 9 11 13 15 17 19
Max. 50mA COM1 HI LO
1 3 5
0V A (+ SG
7 9 11 13 15 17 19
Max. 50mA
The display value to the 500V measured input varies by
adjusting the offset of the low value. If this display value
PA1: Direct
input
Press ,
Short circuit
external Hold
:.:.J~ Set address of RS485 communication output.
ADRS Setting range: 01 to 99 pressing 1ml key for 3 sec.
key for 3sec
Description correction terminal no.
is "501 0", calculate 500.0/501.0 (the desired display at the at
::x==::x==::x== against X input value by correction function[ INbH] and α time 9.000 Indication
D3 Data 1 2 3 4 5 6 8 9 10 11 12 13 14 15 16 1 18 19 20 1 2 used as correction function of max. display value[ H SC]. Y 6.000 value for 1. Follow instructions in 'Cautions during Use'. Otherwise, It may cause unexpected accidents.
β time
[~ measured
~
Digit D2 Output DP D C B A DP D C B A DP D C B A DP D C B A DP D Adjustment range is 0.100 to 5.000 and multiply current βY ~ 2. 12-24VDC power supply should be insulated and limited voltage/current or Class 2, SELV power supply device.
3.000 input Input
signal D1 Clock gradient. .. V ..... 3. Install a power switch or circuit breaker in the easily accessible place for supplying or disconnecting the
1.000 1value
D0 Ex)Input:200mVDC , Display:3.000 for MT4W DV type 0 X power.
Data H H L H H H H H L L L H H L H H H H H L H 0.2 0.4 0.6 0.8 1V
A ①Select 0 1VDC (1V) for measured input in Parameter 1.
Data [ B
H
H
: L
L
: H
L
: L
H
:
uq ta
tw
tb
②Standard specification in input: 0 1VDC and 1.000
therefore it has to be 15.000[ H SC] for 1VDC (Input)
in order to display 3.000 for 200mVDC (Input).
Input value
Setting method H SC
① Unavailable
L SC
0.000
INbH
1.000
Note
4. Keep away from high voltage lines or power lines to prevent inductive noise.
In case installing power line and input signal line closely, use line filter or varistor at power line and shielded
wire at input signal line.
signal
C
=tttl L H H H Latch
But it is unable due to setting range is 9.999 ② 7.500 0.000 2.000 In this case, any Do not use near the equipment which generates strong magnetic force or high frequency noise.
rnfhl
D Display 5.000 0.000 3.000 setting methods
H H H H H
4 3 @ 1 In this case, please check below chart.
dot Please set as INbH H SC = 15.000 ④ 3.750 0.000 4.000 display the same Connection with the line filter Connection with the varistor
H H L H H *When clock pulse change High to Low, Data will be output. display value.
3.000 0.000 5.000
Install the ine filter
Display
If measured inputs are 'a' or 'b' and particular values are 'A' or 'B', it will display a=A, b=B as below graph. H: Hysterisis Earth ground
,,,,11,1
lSET
Display Display Display Display Display Display
value value B valueB value B value a b value A No output
B
a b
OFF 5. This unit may be used in the following environments.
A
A A GO If it is equal or lower than Low setting value, LO output is ON. ①Indoors (in the environment condition rated in 'Specifications')
A a b
a b a b A a b B
lST LO H If it is higher than Low setting value, GO output is ON. ②Altitude max. 2,000m
B
Input value Input value Input value Input value Input value Input value
Pollution degree 2
HI
: : e7! H If it is equal or higher than High setting value, HI output is ON.
-
LLLL Flashes when measuremnet input is exceeded the min. allowable input ( 10%) HI LO output is ON when it is equal or higher than Low setting value.
~ ~ !1•
H
D HH Turns ON when display input is exceeded the max. display range (9999) or H SC setting value HhST GO HI output is ON when it is equal or higher than High setting value.
LO H GO output is ON when it is lower than Low/High setting value.
D LL Turns ON when display input is exceeded the min. display range ( 1999) or L SC setting value
F HH Turns ON when input frequency is exceeded the max. display value of measured range HI , :HI: LO output is ON when it is lower than Low setting value.
OVER Flashes when it exceeds zero range (±99)
※Error display is released automatically when it is in the measured and display range.
LlST GO
LO
. . . .;. , :■ '
:
H
:
HI output is ON when it is equal or lower than High setting value.
GO output is ON when it is higher than Low/High setting value.
It is operated same with L ST but LO output does not operated under
~::
※'LLLL' is displayed when the input specification is DC. GO initial Low setting value, and it is ON from under next Low setting value.
※After flashing 'OVER' 2 times when it exceeds the zero range, it returns to RUN mode.
※The above specifications are subject to change and some models may be discontinued without notice.
LdST LO ! i,:, -
H
If this is higher than Low setting value, GO output is ON.
※Be sure to follow cautions written in the instruction manual and the technical descriptions (catalog, homepage). ※ hSETis displayed according to the setting of output operation mode, when user sets "OFF", hSET/ lSETare not displayed. Autonics