Professional Documents
Culture Documents
INSTALLATION AND
USE MANUAL
NOV 2016
Please read this operating manual carefully before installing condensed aerosol generators
LIST OF ILLUSTRATIONS ____________________________________________________ 6
LIST OF TABLES ___________________________________________________________ 7
FOREWORD ______________________________________________________________ 8
1. Administration __________________________________________________________ 9
1.1. Scope. ___________________________________________________________________ 9
1.2. Purpose. _________________________________________________________________ 9
1.3. Trade Marks and Patent _____________________________________________________ 9
1.4. Units and Formulas._________________________________________________________ 9
1.5. Referenced publications ____________________________________________________ 10
1.6. Definitions _______________________________________________________________ 10
2. ENVIRONMENTAL SUMMARY ______________________________________________ 11
2.1. Significant New Alternatives Policy (SNAP List) __________________________________ 11
2.2. Condensed Aerosol Environmental Parameters _____________________________ 12
3. SAFETY SUMMARY ______________________________________________________ 13
3.1. General. _________________________________________________________________ 13
3.1.1. Health Effects. _____________________________________________________________________________ 13
3.2. Hazards to Personnel. ______________________________________________________ 13
3.2.1. Potential Hazards. __________________________________________________________________________ 13
3.2.2. Pre-discharge Alarms and Time Delays. _________________________________________________________ 13
3.2.2.1. Egress. ........................................................................................................................................................................................ 14
3.2.3. Reduced Visibility. __________________________________________________________________________ 14
3.2.4. Toxicity. __________________________________________________________________________________ 14
3.2.5. Thermal Hazards ___________________________________________________________________________ 14
LIST OF ILLUSTRATIONS
LIST OF TABLES
FOREWORD
This manual is written for those who are installing a condensed aerosol fire extinguishing systems for total
flooding applications.
assumes no responsibility for the application of any system other than those addressed in this manual.
The technical data contained in this manual are strictly limited for information only, believes this data to be
accurate, but they are published and presented without any warranty or guarantee whatsoever; disclaims
any liability for any use that may be made of the data and information contained herein by any and all other parties.
IMPORTANT NOTICES
Warranty Disclaimer
Firepro makes no warranties of any kind, either express or implied, including but not limited to
warranties of the firepro products for their fitness for a particular purpose.
Limitation of Liability
In no event, regardless of cause, FIREPRO shall sensate be liable for any indirect, special,
incidental, punitive or consequential damages of any kind, even if advised of the possibility of
such damages.
General
If any part of this disclaimer is determined to be invalid, vold, unenforceable or illegal, including,
but not limited to the warranty disclaimers and liability disclaimers and liability limitations set forth
above, then the invalid or unenforceable provision will be deemed superseded by a valid,
enforceable provision that most closely matches the intend of the original provision and the
remainder of the agreement shall remain in full force and effects. This disclaimer statement is
governed by the laws of Cyprus. You hereby consent to the exclusive jurisdiction and venue of
the Courts of Cyprus, in all disputes arising out of or relating to the use of this product.
Any question concerning the information presented in this manual should be addressed to:
1. Administration
SCOPE.
This manual is a comprehensive guide that contains all the necessary information to design, install, operate
and maintain the condensed aerosol fire extinguishing systems for total flooding applications.
However the manual does not address information related to fire detection.
PURPOSE.
This manual is prepared for the use by competent fire engineers as a basic knowledge of systems
and guidance of those charged with purchasing, designing, installing, operating, and maintaining
condensed aerosol fire extinguishing systems, so that system will function as intended throughout
its life.
The provisions of this manual are considered necessary to provide a sufficient level of protection from loss
of life and property from fire. The manual reflects the state of the art at the time the manual was issued.
TRADE MARKS AND PATENT
condensed aerosol fire extinguishing systems for total flooding applications is a registered trade
mark of:
Celanova Limited, Cyprus Registered Company, Certificate of Incorporation no. HE 142136
condensed aerosol fire extinguishing systems for total flooding applications is a proprietary patent
of:
Celanova Limited,
Cyprus Registered Company, Certificate of Incorporation no. HE 142136
6, Koumandarias & Spyrou Araouzou Str.
Tonia Court II, 6th Floor,
3036 Limassol
Cyprus
2. ENVIRONMENTAL SUMMARY
SIGNIFICANT NEW ALTERNATIVES POLICY (SNAP LIST)
Submission to the U.S. Environmental Protection Agency's (EPA) SNAP Program. The SNAP
Program was originally outlined in 59 FR 13044.
The official EPA document, issued by the Federal Register, is available at Vol. 71, No.
187/ Wednesday, September 27, 2006/ Rules and Regulations.
Under paragraph II, Listing Decisions: Fire Suppression and Explosion Protection – Total
Flooding, at pages 56363/56364.
The attention for the human health protection linked to the environmental protection developed in 1987 the Montreal
Protocol and the Kyoto Conference on 1997 sees http://www.unep.org/ozone)
Environmental parameters
ODP Zero
(Ozone Depletion Potential)
GWP Zero
(Global Warming Potential)
ALT Negligible
(Atmospheric Life Time)
3. SAFETY SUMMARY
GENERAL.
For Material Safety Data Sheet refers to Appendix A
The discharge of a aerosol extinguishing systems could potentially create a hazard to personnel
due to the nature of the aerosol.
Unnecessary exposure of personnel to either the agent or to the by-products generated by the
fire or the fire to be extinguished or extinguished should be avoided.
3.1.1. Health Effects.
The potential adverse health effects are minimal as:
Hazard for humans related to the FPC ( solid aerosol forming compound) has not been found.
Hazard to humans related to the aerosol released by the reaction of the solid compound (FPC) have not
been established because the TLV’s are not applicable, however it is reputed that hazard to humans are
not present when the aerosol is applied as guided by this manual.
Signs and symptoms related to the aerosol phase are only referred to acute exposure and /or chronic
overexposures. In a real life the exposure to the generated aerosol will occur accidentally only and will be
very short, like in the event of an accidental or unexpected discharge when occupant of the protected space
has not evacuated previously. The aerosol extinguishing system shall be installed in normally
unoccupied spaces and /or in spaces where personnel may be present utilizing suitable safeguards.
HAZARDS TO PERSONNEL.
3.2.1. Potential Hazards.
Potential hazards to be considered for individual systems in the protected space and other areas
where the aerosol agent can migrate are the following:
1. Noise:
The discharge of a system or aerosol generator may cause noise loud enough to be startling
but insufficient to cause traumatic injury.
2. Turbulence:
The high-velocity discharge from generators’ outlets may dislodge light objects directly
involved or impinged by the generated aerosol stream. The system discharge may cause
turbulence inside the protected enclosures to move unsecured paper and light objects.
3. Reduced Visibility
When activated, the condensed aerosol generators reduce visibility both during and after
discharge period.
4. Thermal hazard:
The condensed aerosol discharges at elevated temperatures. Depending on the intended
application(s) of the aerosol system, the temperature and minimum clearance from the
discharge outlet are specified by the generators’ data sheets (see APPENDIX “C”).
Immediately after discharge, the aerosol generators can be hot; protective gloves should be
worn by personnel handling generators after discharge.
5. Eye irritation:
Direct contact with the aerosol solid particles being discharged by the system can result in
irritation of the eyes. Exposure of the condensed aerosol to the eyes should be avoided.
3.2.4. Toxicity.
See the Material Safety Data Sheet contained in Appendix A and chapters 3.1 and 3.1.1 of this manual.
3.2.5. Thermal Hazards
condensed aerosol generators shall not be employed at less than the minimum safe distance from
personnel and combustible materials as specified in chapter 5.1.2 and inside the Condensed
Aerosol Generators data sheets contained in appendix “C” of this manual.
Protective gloves shall be worn by personnel removing discharged condensed aerosol
generators.
Therefore, in the flame, during combustion, further to water and carbon dioxide (stable), only unstable
hydroxyl radicals are formed which allow the reaction to continue (phenomenon of auto catalysis).
Legend:
H2 hydrogen stable
O2 oxygen stable
OH- hydroxyl radicals unstable
H2O water stable
H+ hydrogen atoms unstable
O— Oxygen atoms unstable
CO+ + carbon monoxide unstable
CO2 carbon dioxide stable
<1 52
1÷2 19
2÷5 17
>5 12
ENVIRONMENTAL FACTORS
Despite that condensed aerosol extinguishing systems do not represent any significant
environmental concern the unnecessary emission of aerosol extinguishing systems shall be avoided.
All phases of design, installation, testing, and maintenance of condensed aerosol extinguishing
systems shall be performed with the goal of no emission to the environment.
Chemical
Compound CAS # % by Weight
Formula
Gas
Carbon Dioxide CO2 124-38-9 13%-14%
Nitrogen N2 7727-37-9 21%-22%
Water Vapor H2O 7732-18-5 10%-12%
Carbon Monoxide CO 1%-2%
Methane CH4
Hydrogen H2
Particulate
Potassium Carbonate K2CO3 584-08-7 47%-49%
Potassium Nitrate KNO3 7757-79-1 2%-3%
Potassium Chloride KCl 7447-40-7 < 1%
Other elements See KEMA --- <1%
report
Electrical Wire
Electrical Housing
Cover Plate
Electrical Initiator
Solid Aerosol Forming
Compound (FPC)
Metal Housing
Cooling Material
Sealing
The initiator is connected to the activation power circuit (minimum current required 0.8 A for 3-
4seconds) by heat resistant wires. The activation power will heat up the electric coil (4) thus the (5)
solid aerosol forming compound (FPC) will initiate an exothermal reaction. The heat developed will
transfer thorough the cylinder (7) outlets starting the exothermal reaction of the (9) FPC thus the
thermal energy will be sufficient to start the reaction of the whole mass of FPC contained inside the
aerosol generator, transforming the FPC into a particulate aerosol and carrier gases.
4 electric coil
Electrical values
Bridge resistance 1.6-3.0 Ohms( )
Ignition pulse From 1- 2 mWs/
no fire value < 20 mA t = 300s
Deployment
-54° C to 100° C
temperature
Storage temperature -54° C to 54° C
INTRODUCTION
7.1.1. Working documents
The design of a condensed aerosol total flooding fire extinguishing systems shall be prepared
only by a person qualified and experienced in designing extinguishing systems, in accordance with the
advice of the authority having jurisdiction.
Deviation from the working documents shall require the permission and the agreements of the authority
having jurisdiction.
The working documents shall include, as minimum requirement, the following:
7.1.1.1. Specifications.
Designation of the authority having jurisdiction,
Variances from the standard to be permitted by the authority having jurisdiction,
Design criteria,
System sequence of operations,
Functional testing to be performed after installation of the system,
System’s owner/user training requirements.
7.1.4.2. Extinguishment.
Class B Fuels:
The extinguishing application density of condensed aerosol for Class B fuels has been
determined by test as per UL 2775.
The minimum design application density for a Class B fuel hazard is the extinguishing application
density multiplied by a safety factor of 1.3.
Class A Fuels:
The extinguishing application density of condensed aerosol for Class A fuels has been
determined by test as per UL 2775.
The minimum design application density for a Class A Fuels fire hazard is the extinguishing
application density multiplied by a safety factor of 1.3.
Class C Fuel:
The minimum design application density of condensed aerosol for Class C hazards shall
be at least that for the Class of fire hazard being protected ‘’’’
Fuel combination:
For combinations of Class A and B fuels the design application density shall be the value for the fuel
requiring the greatest design application density.
Table 7.1.4.2
Class of Fire Extinguishing application Minimum design application
density density
ELECTRICAL CLEARANCES.
All system components shall be located to maintain no less than a minimum clearances from
energized electrical parts as per:
1. ANSI C2
2. NFPA 70
3. 29 CFR 1910, Subpart S
4. Canadian Electrical Code, CSA C22.1
Where the design basic insulation level (BIL) is not available, and where nominal voltage is used for the
design criteria, the highest minimum clearance listed for this group shall be used.
The selected clearance to ground shall satisfy the greater of the switching surge or BIL duty, rather than
being based on nominal voltage.
The clearance between non insulated, energized parts of the electrical system equipment and any portion
of the condensed aerosol extinguishing system shall not be less than the minimum clearance
provided elsewhere for electrical system insulations on any individual component
STORAGE CONDITIONS:
Temperature : between –54 and +54°C
Humidity : maximum 98% RH
This manual does not address information related to fire detection; however the following general information shall
be considered.
9.1.2. Raceways.
system initiating circuits and auxiliary equipment releasing circuits shall be installed in raceways.
Unless shielded and grounded, alternating current (AC) and direct current (DC) wiring shall not be
combined in a common conduit or raceway.
Ceiling
ILLUSTRATION 10b:
RECOMMENDED condensed aerosol arrangement
ILLUSTRATION 10c:
WRONG condensed aerosol arrangement
The location of generators shown above is incorrect. The generators aerosol outlets are pointing the
aerosol stream in the direction of the opening (a door).
If the door will left open at the time of the generators activation the generated aerosol will escape from
the protected volume. Thus depleting the aerosol design factor that may result in failure to extinguish the fire.
ILLUSTRATION 10d:
ALLOWED condensed aerosol arrangement
The condensed aerosol generators shall be positioned in the protected space/volume so that the
aerosol flow does not obstruct/impede the evacuation of personnel.
ILLUSTRATION 11.1:
2
3
LEGEND
1 Power supply with outlet between 6-36V DC
2 Manual Release Button (Hand-operated switch)
3 condensed aerosol generators connected units
These condensed aerosol units require a minimum of 0.8 A activation current each. The power
may be delivered by a 6-36V battery pack. Care shall be taken in observing the maximum current required.
ILLUSTRATION11.1.1a:
6
5
7
1
3
2
LEGEND
1 Abort Button (Isolation Switch) 2 Extinguishing Control Panel
3 Manual Release Button (Hand-operated switch) 4 Bell, Siren
5 Automatic fire alarm detectors 6 condensed aerosol generators
Aerosol Generators are activated two by two in sequence through the sequential activators array. Low power
consumption from panel during activation of the aerosol generators.
ILLUSTRATION11.1.1b:
6 5
1 7
3
2
LEGEND
1 Abort Button (Isolation Switch) 2 Extinguishing Control Panel
3 Manual Release Button (Hand-operated switch) 4 Bell, Siren
5 Automatic fire alarm detectors 6 condensed aerosol generators
Control panel back-up batteries at 100% capacity: 16 Aerosol Generators can be used in series connection.
Control panel back-up batteries at 65% capacity: 4 Aerosol Generators can be used in series connection.
ILLUSTRATION 11.1.1c:
ILLUSTRATION 11.1.1d:
12.2.3.2.Field circuits
All field circuits shall be free of ground faults and short circuits.
Where field circuitry is being measured, all electronic components, such as smoke and flame detectors or
special electronic equipment for other detectors or their mounting bases, shall be removed and jumpers shall
be installed to prevent the possibility of damage within these devices.
Components shall be replaced after measuring.
12.2.3.3.Power Supply
Power shall be supplied to the control unit from a separate dedicated source that will not be shut down on
system operation.
Reliable primary and 24-hour minimum standby sources of energy shall be used to provide for operation of
the detection, signaling, control, and actuation requirements of the system.
RESIDUE
14.3.1. Instructions
VERY IMPORTANT:
- Disassemble or switch off the drive from the fire detection system and ensure that it
cannot be switched on;
- Disconnect the power wires from the condensed aerosol generators and
ensure that they cannot be connected;
- Ensure that you are standing firmly and comply with the rules for working at height
(Working Conditions Act);
- Remove the condensed aerosol generators by unscrewing the bolts and
nuts fixing them;
- Carefully remove the condensed aerosol generators from the brackets
and place it on a stable surface;
- After removing the condensed aerosol generators, put the fire detection
and alarm installation back into operation in accordance with the guidance of the
Authority Having Jurisdiction.
- If the condensed aerosol generators are still warm (after activation), wear
heat-resistant gloves.
Systems Ltd.
Systems Ltd.
Systems Ltd.
Systems Ltd.
Systems Ltd.
17. Disclaimer
17.1 The data in the above material safety data sheet reflect the current state of knowledge of our product and shall be
used only as a guideline. No binding statements as to the contractually agreed product characteristics may be inferred
there from.
THE FOLLOWING REFERENCED PUBLICATIONS ARE EXCERPT FROM NFPA 2010 STANDARD FOR FIXED AEROSOL
FIRE-EXTINGUISHING SYSTEMS 2015 EDITION.
THEY ARE ADOPTED IN THIS MANUAL AS A CONSISTENT REFERENCE WITH THE CODE.
GENERAL.
The documents or portion thereof listed in this chapter are referenced within this manual and shall be
considered part of the guidance of this manual.
NFPA PUBLICATION.
National Fire Protection Association, 1 Batterymarch Park, Quincy, MA 02169-7471
NFPA 2010 Standard for Fixed Aerosol Fire-Extinguishing Systems – 2015 Edition
NFPA 70 National Electrical Code® , 2014 Edition
NFPA 72 National Fire Alarm Code® , 2016 Edition
NFPA 2001 Standard on Clean Agent Fire Extinguishing Systems - 2015 Edition
ANSI PUBLICATION.
American National Standard Institute, Inc., 25 West 43 rd Street, 4th Floor; New York, NY10036
ANSI C2, National Electrical Safety Code, 2012
IMO PUBLICATION.
International Maritime Organization, 4 Albert Embankments, London, SE1 7SR, United Kingdom.
IMO MSC/Circ.1270, Guidelines for the Approval of Fixed Aerosol Fire-Extinguishing Systems
Equivalent to Fixed Gas Fire-Extinguishing Systems, as Referred to in SOLAS 74, for Machinery
Spaces; 2008 Edition
ISO PUBLICATION.
International Organization for Standardization, 1, Rue de Varembe, Case postale 56, CH-1211 Geneve 20,
Switzerland.
ISO /lEC Guide 7, Requirements for Standards Suitable for Use for Conformity Assessment, 1994.
THE FOLLOWING DEFINITIONS ARE EXCERPT FROM NFPA 2010 STANDARD FOR FIXED AEROSOL FIRE-EXTINGUISHING
SYSTEMS 2015 EDITION.
THEY ARE ADOPTED IN THIS MANUAL AS A CONSISTENT REFERENCE WITH THE CODE.
The definitions contained in this chapter shall apply to the terms used in this manual. Where terms are not defined
in this chapter or within another chapter, they shall be defined using their ordinary accepted meanings within the
context in witch they are used.
Merriam-Webster’s Collegiate Dictionary, 11th edition, shall be the source for the ordinarily accepted meaning.
GENERAL
20.1.1. Approved.
Acceptable to the authority having jurisdiction.
20.1.2. Authority Having Jurisdiction (AHJ).
An organization, office, or individual responsible for enforcing the requirements of a code or standard, or
for approving equipment, materials, an installation, or a procedure.
20.1.3. Listed.
Equipment, materials, or services included in a list published by an organization that is acceptable to the
authority having jurisdiction and concerned with evaluation of products or services, that maintains periodic
inspection of production of listed equipment or materials or periodic evaluation of services, and whose
listing states that either the equipment, material, or service meets appropriate designated standards or has
been tested and found suitable for a specified purpose.
20.1.4. Shall.
Indicates a mandatory requirement.
20.1.5. Should.
Indicates a recommendation or that which is advised but not required.
20.1.6. Standard.
A document, the main text of which contains only mandatory provisions using the word "shall" to indicate
requirements and which is in a form generally suitable for mandatory reference by another standard or
code or for adoption into law. Non-mandatory provisions shall be located in an appendix or annex, footnote,
or fine-print note and are not to be considered a part of the requirements of a standard.
APPENDIX “C”
DATA SHEETS
NOV 2016
FirePro ® Condensed Aerosol generators: Legend of symbol
Activation Mode Max volume protected
Electrical activation
A Ma 3
X
x
m
Max volume protected for Class “A” Fire
X
B x
Ma 3
m
Max volume protected for Class “B” Fire
XX
C x
Ma 3
m
Max volume protected for Class “C” Fire
XX
Classification of fires
Following the EN 2 Classification of Fire the fire classification iden- Following the NFPA 10 Standard for portable fire extinguisher the
tify the combustible material originating the fire: fire classification identify the combustible material originating the fire:
CLASS
nature (such as paper, wood, plastics and so on), Fire in ordinary combustible materials such as
“A”
“A”
in which combustion normally takes place with the wood, cloth, paper, rubber and many plastics.
formation of glowing embers.
CLASS
CLASS
“D” 1
CLASS
“E” 2
CLASS
“K” 3
K
“F”
Fire involving cooking oils and fat and such like. Fire involving cooking grease, fats and oils.
(*) Comite Europeen de Normalisation (CEN standard EN2) closely follows ISO standard 3941
(1) FirePro ® is not suitable to extinguish Class D fires (see technical manual)
Note:
(2) Code of practice definition, not included inside EN2
(3) Not tested to Class K fires
discharge outlet
Weight (g)
Number of
(m)
(s)
Diameter
Height
Electrical
Gross
Max
Min
Net
T1
T2
T3
2
Length
Height
Width
T2 Aerosol stream temperature from generator discharge outlet equal or less than 200° C
T3 Aerosol stream temperature from generator discharge outlet equal or less than 75° C
(1) In case of generator’s system activation failure the FPC (FirePro. solid compound) will start by itself the aerosol forming reaction when reaching
the temperature of 300° C.
3000 3000
2500 2500
2000 2000
1500 1500
1000 1000
900 900
800 800
700 700
600 600
0500 0500
400 400
300 300
200 200
Generator outlet
Generator outlet
Distance From
Distance From
100 100
0 0
FP-500S
FP-80T FP-100S FP-200S
mm
mm
FP-20SE FP-20T FP-40S FP-40T FP-80S
20
40
20
40
80
80 5
2 0
0
100 0
0
0 0
100 100
200 200
300 300
400 400
500 0500
600 600
700 700
800 800
900 900
1000 1000
1500 1500
2000 2000
2500 2500
3000 3000
Generator outlet
Generator outlet
Distance From
Distance From
FP-1200 FP-2000
FP-1200 FP-2000
FP-3000
FP-3000
FP-4200T
FP-4200
FP-5700
FP-5700
mm
mm
0 0
100 100
200 200
300 300
400 400
500 0500
600 600
700 700
800 800
900 900
1000 1000
1500 1500
2000 2000
2500 2500
3000 3000
3500 3500
4000 4000
4500 4500
5000 5000
5500 5500
6000 6000
6500 6500
LEGEND
Maximum Height Of installation => Discharge Length
7000 7000
0
Minimum clearance from persons => >75 C = L3
7500 7500
Minimum clearance from combustible materials => >2000 C = L2
8000
Minimum clearance from construction structure => >4000 C = L1 8000
8500 8500
500
400
300
100
FP-20SE
0
A Max 3
0 . 18
m B Max 3
0.18
m C Max 3
0.18
m
20
0 LEGEND
100 Maximum Height Of installation
Technical Data
Mass of FPC (Aerosol Generating Solid Compound) 20 g
Weight Tolerance
Generators gross weight
310 g ± 5%
Activation mode/s Electrically
Value of activation 6/12/24/36 V D/C 0.8 A 3-4 s
FPC activation device Heating elements with 1.6-3.6 Ω Resistance
Activation line supervision current (Max) 5 mA
Min. Max
Aerosol discharge time
3 seconds 6 seconds
Number of discharge outlet 2
Height Diameter
Generator dimension
165 mm 32 mm
Self-activation temperature of FPC 300° C
Classes of Fire A B C D K
(NFPA 2010) √ √ √ NO NO
Generator Coverage Constraints Min ht: 0.45 m Max area: 0.55 m2 Max throw: 0.27 m
Maximum height of installation 1.0 m
From persons From combustible material From Generator’s Casing
Minimum clearance (mm)
100 mm 0 mm 6.4 mm
ODP1 GWP2 ALT3
Environmental parameters
Zero Zero Negligible4
Electrical conductivity Corrosion Oxygen depletion After discharge
Technical Parameters
Nil up to 75KV Negligible4 Negligible4
1 ODP: Ozone Depletion Potential 3 ALT: Atmospheric Life Time
Note
2 GWP: Global Worming Potential 4 Within the parameters for use
FP-20T
20
0
100
300 A Max 3
0.18
m
Max 3
0.18
m
Max 3
0.18
m
400
500
LEGEND
Maximum Height Of installation
600
Minimum clearance from persons
700
Minimum clearance from combustible materials
800
1000
Technical Data
Mass of FPC (Aerosol Generating Solid Compound) 20 g
Weight Tolerance
Generators gross weight
310 g ± 5%
Activation mode/s Electrically
Value of activation 6/12/24/36 V D/C 0.8 A 3-4 s
FPC activation device Heating elements with 1.6-3.6 Ω Resistance
Activation line supervision current (Max) 5 mA
Min. Max
Aerosol discharge time
3 seconds 6 seconds
Number of discharge outlet 1
Height Diameter
Generator dimension
165 mm 32 mm
Self-activation temperature of FPC 300° C
Classes of Fire A B C D K
(NFPA 2010) √ √ √ NO NO
Generator Coverage Constraints Min ht: 0.45 m Max area: 0.55 m2 Max throw: 1.14 m
Maximum height of installation 1.0 m
From persons From combustible material From Generator’s Casing
Minimum clearance (mm)
0 mm 0 mm 6.4 mm
ODP1 GWP2 ALT3
Environmental parameters
Zero Zero Negligible4
Electrical conductivity Corrosion Oxygen depletion After discharge
Technical Parameters
Nil up to 75KV Negligible4 Negligible4
1 ODP: Ozone Depletion Potential 3 ALT: Atmospheric Life Time
Note
2 GWP: Global Worming Potential 4 Within the parameters for use
500
400
300
100
FP-40S
A Max 3
0.36
m B Max 3
0.36
m C Max 3
0.36
m
40
0 LEGEND
100 Maximum Height Of installation
Technical Data
Mass of FPC (Aerosol Generating Solid Compound) 40 g
Weight Tolerance
Generators gross weight
610 g ± 5%
Activation mode/s Electrically
Value of activation 6/12/24/36 V D/C 0.8 A 3-4 s
FPC activation device Heating elements with 1.6-3.6 Ω Resistance
Activation line supervision current (Max) 5 mA
Min. Max
Aerosol discharge time
5 seconds 10 seconds
Number of discharge outlet 2
Height Diameter
Generator dimension
140 mm 51 mm
Self-activation temperature of FPC 300° C
Classes of Fire A B C D K
(NFPA 2010) √ √ √ NO NO
Generator Coverage Constraints Min ht: 0.45 m Max area: 1.08 m2 Max throw: 0.54 m
Maximum height of installation 1m
From persons From combustible material From Generator’s Casing
Minimum clearance (mm)
100 mm 0 mm 6.4 mm
ODP1 GWP2 ALT3
Environmental parameters
Zero Zero Negligible4
Electrical conductivity Corrosion Oxygen depletion After discharge
Technical Parameters
Nil up to 75KV Negligible4 Negligible4
1 ODP: Ozone Depletion Potential 3 ALT: Atmospheric Life Time
Note
2 GWP: Global Worming Potential 4 Within the parameters for use
40
0
100
300
A Max 3
0.36
m B Max 3
0.36
m C Max 3
0.36
m
400
500 LEGEND
Maximum Height Of installation
600
Minimum clearance from persons
700
1000
Technical Data
Mass of FPC (Aerosol Generating Solid Compound) 40 g
Weight Tolerance
Generators gross weight
615 g ± 5%
Activation mode/s Electrically
Value of activation 6/12/24/36 V D/C 0.8 A 3-4 s
FPC activation device Heating elements with 1.6-3.6 Ω Resistance
Activation line supervision current (Max) 5 mA
Min. Max
Aerosol discharge time
5 seconds 10 seconds
Number of discharge outlet 1
Height Diameter
Generator dimension
140 mm 51 mm
Self-activation temperature of FPC 300° C
Classes of Fire A B C D K
(NFPA 2010) √ √ √ NO NO
Generator Coverage Constraints Min ht: 0.45 m Max area: 1.08 m2 Max throw: 1.47 m
Maximum height of installation 1m
From persons From combustible material From Generator’s Casing
Minimum clearance (mm)
0 mm 0 mm 6.4 mm
ODP1 GWP2 ALT3
Environmental parameters
Zero Zero Negligible4
Electrical conductivity Corrosion Oxygen depletion After discharge
Technical Parameters
Nil up to 75KV Negligible4 Negligible4
1 ODP: Ozone Depletion Potential 3 ALT: Atmospheric Life Time
Note
2 GWP: Global Worming Potential 4 Within the parameters for use
1000
900
700
600
500
B C
100
0
FP-80S
A Max 3
0.73
m
Max 3
0.73
m
Max 3
0.73
m
80
0 LEGEND
100
Maximum Height Of installation
200
300
Minimum clearance from persons
400
500
600 Minimum clearance from combustible materials
700
Technical Data
Mass of FPC (Aerosol Generating Solid Compound) 80 g
Weight Tolerance
Generators gross weight
870 g ± 5%
Activation mode/s Electrically
Value of activation 6/12/24/36 V D/C 0.8 A 3-4 s
FPC activation device Heating elements with 1.6-3.6 Ω Resistance
Activation line supervision current (Max) 5 mA
Min. Max
Aerosol discharge time
5 seconds 10 seconds
Number of discharge outlet 2
Height Diameter
Generator dimension
185 mm 51 mm
Self-activation temperature of FPC 300° C
Classes of Fire A B C D K
(NFPA 2010) √ √ √ NO NO
Generator Coverage Constraints Min ht: 0.45 m Max area: 2.12 m2 Max throw: 1.06 m
Maximum height of installation 2m
From persons From combustible material From Generator’s Casing
Minimum clearance (mm)
100 mm 0 mm 6.4 mm
ODP1 GWP2 ALT3
Environmental parameters
Zero Zero Negligible4
Electrical conductivity Corrosion Oxygen depletion After discharge
Technical Parameters
Nil up to 75KV Negligible4 Negligible4
1 ODP: Ozone Depletion Potential 3 ALT: Atmospheric Life Time
Note
2 GWP: Global Worming Potential 4 Within the parameters for use
FP-80T
80
0
100
200
600
700 LEGEND
800 Maximum Height Of installation
900
Minimum clearance from persons
1000
1100
Minimum clearance from combustible materials
Technical Data
Mass of FPC (Aerosol Generating Solid Compound) 80 g
Weight Tolerance
Generators gross weight
840 g ± 5%
Activation mode/s Electrically
Value of activation 6/12/24/36 V D/C 0.8 A 3-4 s
FPC activation device Heating elements with 1.6-3.6 Ω Resistance
Activation line supervision current (Max) 5 mA
Min. Max
Aerosol discharge time
5 seconds 10 seconds
Number of discharge outlet 1
Height Diameter
Generator dimension
185 mm 51 mm
Self-activation temperature of FPC 300° C
Classes of Fire A B C D K
(NFPA 2010) √ √ √ NO NO
Generator Coverage Constraints Min ht: 0.45 m Max area: 2.12 m2 Max throw: 2.34 m
Maximum height of installation 2m
From persons From combustible material From Generator’s Casing
Minimum clearance (mm)
0 mm 0 mm 6.4 mm
ODP1 GWP2 ALT3
Environmental parameters
Zero Zero Negligible4
Electrical conductivity Corrosion Oxygen depletion After discharge
Technical Parameters
Nil up to 75KV Negligible4 Negligible4
1 ODP: Ozone Depletion Potential 3 ALT: Atmospheric Life Time
Note
2 GWP: Global Worming Potential 4 Within the parameters for use
FP-100S
100
100
300
A Max 3
0.91
m B Max 3
0.91
m C Max 3
0.91
m
400
500 LEGEND
Maximum Height Of installation
600
Minimum clearance from persons
700
1000
Technical Data
Mass of FPC (Aerosol Generating Solid Compound) 100 g
Weight Tolerance
Generators gross weight
1370 g ± 5%
Activation mode/s Electrically
Value of activation 6/12/24/36 V D/C 0.8 A 3-4 s
FPC activation device Heating elements with 1.6-3.6 Ω Resistance
Activation line supervision current (Max) 5 mA
Min. Max
Aerosol discharge time
5 seconds 10 seconds
Number of discharge outlet 1
Height Diameter
Generator dimension
155 mm 84 mm
Self-activation temperature of FPC 300° C
Classes of Fire A B C D K
(NFPA 2010) √ √ √ NO NO
Generator Coverage Constraints Min ht: 0.45 m Max area: 2.65 m2 Max throw: 1.82 m
Maximum height of installation 1m
From persons From combustible material From Generator’s Casing
Minimum clearance (mm)
200 mm 0 mm 6.4 mm
ODP1 GWP2 ALT3
Environmental parameters
Zero Zero Negligible4
Electrical conductivity Corrosion Oxygen depletion After discharge
Technical Parameters
Nil up to 75KV Negligible4 Negligible4
1 ODP: Ozone Depletion Potential 3 ALT: Atmospheric Life Time
Note
2 GWP: Global Worming Potential 4 Within the parameters for use
FP-200S
2
0
0
0
100
200
600
700 LEGEND
800 Maximum Height Of installation
900
Minimum clearance from persons
1000
1100
Minimum clearance from combustible materials
Technical Data
Mass of FPC (Aerosol Generating Solid Compound) 200 g
Weight Tolerance
Generators gross weight
1840 g ± 5%
Activation mode/s Electrically
Value of activation 6/12/24/36 V D/C 0.8 A 3-4 s
FPC activation device Heating elements with 1.6-3.6 Ω Resistance
Activation line supervision current (Max) 5 mA
Min. Max
Aerosol discharge time
5 seconds 10 seconds
Number of discharge outlet 1
Height Diameter
Generator dimension
185 mm 84 mm
Self-activation temperature of FPC 300° C
Classes of Fire A B C D K
(NFPA 2010) √ √ √ NO NO
Generator Coverage Constraints Min ht: 0.45 m Max area: 5.29 m2 Max throw: 2.57 m
Maximum height of installation 2m
From persons From combustible material From Generator’s Casing
Minimum clearance (mm)
300 mm 0 mm 6.4 mm
ODP1 GWP2 ALT3
Environmental parameters
Zero Zero Negligible4
Electrical conductivity Corrosion Oxygen depletion After discharge
Technical Parameters
Nil up to 75KV Negligible4 Negligible4
1 ODP: Ozone Depletion Potential 3 ALT: Atmospheric Life Time
Note
2 GWP: Global Worming Potential 4 Within the parameters for use
FP-500S
5
0
0
0
100
200
600
700 LEGEND
800 Maximum Height Of installation
900
Minimum clearance from persons
1000
1100
Minimum clearance from combustible materials
Technical Data
Mass of FPC (Aerosol Generating Solid Compound) 500 g
Weight Tolerance
Generators gross weight
1840 g ± 5%
Activation mode/s Electrically
Value of activation 6/12/24/36 V D/C 0.8 A 3-4 s
FPC activation device Heating elements with 1.6-3.6 Ω Resistance
Activation line supervision current (Max) 5 mA
Min. Max
Aerosol discharge time
5 seconds 10 seconds
Number of discharge outlet 1
Height Diameter
Generator dimension
185 mm 84 mm
Self-activation temperature of FPC 300° C
Classes of Fire A B C D K
(NFPA 2010) √ √ √ NO NO
Generator Coverage Constraints Min ht: 0.45 m Max area: 5.29 m2
Maximum height of installation 2m
From persons From combustible material From Generator’s Casing
Minimum clearance (mm)
500 mm 100 mm 6.4 mm
ODP1 GWP2 ALT3
Environmental parameters
Zero Zero Negligible4
Electrical conductivity Corrosion Oxygen depletion After discharge
Technical Parameters
Nil up to 75KV Negligible4 Negligible4
1 ODP: Ozone Depletion Potential 3 ALT: Atmospheric Life Time
Note
2 GWP: Global Worming Potential 4 Within the parameters for use
FP-1200
0
100
200
300
400
A B C
600
700
800 Max 3 Max 3 Max 3
9m 9m 9m
1000
900
10.9 10.9 10.9
LEGEND
1500
Maximum Height Of installation
3100
3200
Minimum clearance from construction structure
3300
3400
3500
Technical Data
Mass of FPC (Aerosol Generating Solid Compound) 1200 g
Weight Tolerance
Generators gross weight
10900 g ± 5%
Activation mode/s Electrically
Value of activation 6/12/24/36 V D/C 0.8 A 3-4 s
FPC activation device Heating elements with 1.6-3.6 Ω Resistance
Activation line supervision current (Max) 5 mA
Min. Max
Aerosol discharge time
15 seconds 20 seconds
Number of discharge outlet 1
Height Width Length
Generator dimension
167 mm 216 mm 300 mm
Self-activation temperature of FPC 300° C
Classes of Fire A B C D K
(NFPA 2010) √ √ √ NO NO
Generator Coverage Constraints Min ht: 0.45 m Max area: 32 m2
Maximum height of installation 3.5 m
From persons From combustible material From Generator’s Casing
Minimum clearance (mm)
1500 mm 0 mm 6.4 mm
ODP1 GWP2 ALT3
Environmental parameters
Zero Zero Negligible4
Electrical conductivity Corrosion Oxygen depletion After discharge
Technical Parameters
Nil up to 75KV Negligible4 Negligible4
1 ODP: Ozone Depletion Potential 3 ALT: Atmospheric Life Time
Note
2 GWP: Global Worming Potential 4 Within the parameters for use
FP-2000
0
100
200
300
400
A B C
600
700
800 Max 3 Max 3 Max 3
1m 1m 1m
1000
900
18.3 18.3 18.3
LEGEND
1500
Maximum Height Of installation
3100
3200
Minimum clearance from construction structure
3300
3400
3500
Technical Data
Mass of FPC (Aerosol Generating Solid Compound) 2000 g
Weight Tolerance
Generators gross weight
15500 g ± 5%
Activation mode/s Electrically
Value of activation 6/12/24/36 V D/C 0.8 A 3-4 s
FPC activation device Heating elements with 1.6-3.6 Ω Resistance
Activation line supervision current (Max) 5 mA
Min. Max
Aerosol discharge time
15 seconds 20 seconds
Number of discharge outlet 1
Height Width Length
Generator dimension
185 mm 300 mm 300 mm
Self-activation temperature of FPC 300° C
Classes of Fire A B C D K
(NFPA 2010) √ √ √ NO NO
Generator Coverage Constraints Min ht: 0.45 m Max area: 32.03 m2
Maximum height of installation 3.5 m
From persons From combustible material From Generator’s Casing
Minimum clearance (mm)
1500 mm 0 mm 6.4 mm
ODP1 GWP2 ALT3
Environmental parameters
Zero Zero Negligible4
Electrical conductivity Corrosion Oxygen depletion After discharge
Technical Parameters
Nil up to 75KV Negligible4 Negligible4
1 ODP: Ozone Depletion Potential 3 ALT: Atmospheric Life Time
Note
2 GWP: Global Worming Potential 4 Within the parameters for use
FP-3000
0
100
200
300
400
A B C
600
700
800 Max 3 Max 3 Max 3
7m 7m 7m
1000
900
27.4 27.4 27.4
LEGEND
1500
Maximum Height Of installation
3100
3200
Minimum clearance from construction structure
3300
3400
3500
Technical Data
Mass of FPC (Aerosol Generating Solid Compound) 3000 g
Weight Tolerance
Generators gross weight
16300 g ± 5%
Activation mode/s Electrically
Value of activation 6/12/24/36 V D/C 0.8 A 3-4 s
FPC activation device Heating elements with 1.6-3.6 Ω Resistance
Activation line supervision current (Max) 5 mA
Min. Max
Aerosol discharge time
15 seconds 20 seconds
Number of discharge outlet 1
Height Width Length
Generator dimension
185 mm 300 mm 300 mm
Self-activation temperature of FPC 300° C
Classes of Fire A B C D K
(NFPA 2010) √ √ √ NO NO
Generator Coverage Constraints Min ht: 0.45 m Max area: 32.03 m2
Maximum height of installation 3.5 m
From persons From combustible material From Generator’s Casing
Minimum clearance (mm)
2000 mm 600 mm 6.4 mm
ODP1 GWP2 ALT3
Environmental parameters
Zero Zero Negligible4
Electrical conductivity Corrosion Oxygen depletion After discharge
Technical Parameters
Nil up to 75KV Negligible4 Negligible4
1 ODP: Ozone Depletion Potential 3 ALT: Atmospheric Life Time
Note
2 GWP: Global Worming Potential 4 Within the parameters for use
FP-4200T
0
100
200
300
400
A B C
600
700
800 Max 3 Max 3 Max 3
6m 6m 6m
1000
900
38.4 38.4 38.4
LEGEND
1500
Maximum Height Of installation
4600
4700
Minimum clearance from construction structure
4800
4900
5000
Technical Data
Mass of FPC (Aerosol Generating Solid Compound) 4200 g
Weight Tolerance
Generators gross weight
23600 g ± 5%
Activation mode/s Electrically
Value of activation 6/12/24/36 V D/C 0.8 A 3-4 s
FPC activation device Heating elements with 1.6-3.6 Ω Resistance
Activation line supervision current (Max) 5 mA
Min. Max
Aerosol discharge time
15 seconds 20 seconds
Number of discharge outlet 1
Height Width Length
Generator dimension
300 mm 300 mm 300 mm
Self-activation temperature of FPC 300° C
Classes of Fire A B C D K
(NFPA 2010) √ √ √ NO NO
Generator Coverage Constraints Min ht: 0.45 m Max area: 32 m2
Maximum height of installation 5m
From persons From combustible material From Generator’s Casing
Minimum clearance (mm)
2300 mm 990 mm 6.4 mm
ODP1 GWP2 ALT3
Environmental parameters
Zero Zero Negligible4
Electrical conductivity Corrosion Oxygen depletion After discharge
Technical Parameters
Nil up to 75KV Negligible4 Negligible4
1 ODP: Ozone Depletion Potential 3 ALT: Atmospheric Life Time
Note
2 GWP: Global Worming Potential 4 Within the parameters for use
FP-5700
0
100
200
300
400
A B C
600
700
800 Max 3 Max 3 Max 3
9m 9m 9m
1000
900
52.1 52.1 52.1
LEGEND
1500
Maximum Height Of installation
Technical Data
Mass of FPC (Aerosol Generating Solid Compound) 5700 g
Weight Tolerance
Generators gross weight
26400 g ± 5%
Activation mode/s Electrically
Value of activation 6/12/24/36 V D/C 0.8 A 3-4 s
FPC activation device Heating elements with 1.6-3.6 Ω Resistance
Activation line supervision current (Max) 5 mA
Min. Max
Aerosol discharge time
15 seconds 20 seconds
Number of discharge outlet 1
Height Width Length
Generator dimension
300 mm 300 mm 300 mm
Self-activation temperature of FPC 300° C
Classes of Fire A B C D K
(NFPA 2010) √ √ √ NO NO
Generator Coverage Constraints Min ht: 0.45 m Max area: 32 m2
Maximum height of installation 8.4 m
From persons From combustible material From Generator’s Casing
Minimum clearance (mm)
2000 mm 600 mm 6.4 mm
ODP1 GWP2 ALT3
Environmental parameters
Zero Zero Negligible4
Electrical conductivity Corrosion Oxygen depletion After discharge
Technical Parameters
Nil up to 75KV Negligible4 Negligible4
1 ODP: Ozone Depletion Potential 3 ALT: Atmospheric Life Time
Note
2 GWP: Global Worming Potential 4 Within the parameters for use
APPENDIX “D”
INSTALLATION DRAWINGS
NOV 2016
2 1
3
78
4 5
Installation Options
5 1 BRACKET C20BR
4 1 BOTTOM OUTLET COVER PLATE C20BOCS
55.0
3 1 HOUSING TUBE C20HTS
2 1 THERMOCONNECTOR C1-2-5THC
1 1 TOP OUTLET COVER PLATE C20TOCS
Quantity
Position
Type /
Denomination
DWG. Number
4 5
Installation Options
5 1 BRACKET C20BR
4 1 BOTTOM OUTLET COVER PLATE C20BOCS
55.0
3 1 HOUSING TUBE C20THT
2 1 BTA BLISTER ASSEMBLY BTABLASS
1 1 TOP COVER PLATE C2TTCP
Quantity
Position
Type /
Denomination
DWG. Number
Installation Options
Type /
Denomination
DWG. Number
Installation Options
Type /
Denomination
DWG. Number
Installation Options
Type /
Denomination
DWG. Number
Installation Options
.0
Ø6
Quantity
Position
Type /
Denomination
DWG. Number
Installation Options
.0
Ø6
Quantity
Position
Type /
Denomination
DWG. Number
Top View
Iso View (Top)
Installation Options
26.0
4 1 HOUSING TUBE C2HT
3 1 ANGLE BRACKET SUPPORT C1-2-5ABS
2 1 IGNITER C1-2-5IGN
1 1 BTA BLISTER PART 2 BTABLP2
21.5
6.0
Quantity
Ø
Position
Type /
Denomination
DWG. Number
Installation Options
26.0
5 1 HOUSING EXIT COVER C5HEC
4 1 HOUSING TUBE C5HT
21.5
Quantity
Position
Type /
Denomination
DWG. Number
PART LIST
21.5
1 2
3
Top View
Iso View (Top)
Installation Options
5 1 AEROSOL OUTLET
0
52.0
4 1
0.
GENERATOR
Ø1
Type /
Denomination
DWG. Number
216
3
Bottom View 6
Iso View(Bottom)
292
167
CEILING WALL
Installation Options
6 1 OUTLET B12EHTC
1 1 THERMOCONNECTOR BTHC
81.4
Quantity
Position
Type /
41.4
Denomination
DWG. Number
PART LIST
FirePro Systems Ltd FP-1200
Condensed aerosol generator FP-1200S
Fixing Drills DRAWING NUMBER: ID-1200/S TITLE:
DATE: 15/04/10 INSTALLATION DRAWING
5
216
3
2
300
Bottom View 6
Iso View(Bottom)
292
167
CEILING WALL
Installation Options
6 1 OUTLET B12EHTC
Quantity
Position
Type /
41.4
Denomination
DWG. Number
PART LIST
FirePro Systems Ltd FP-1200T
Condensed aerosol generator FP-1200TS
Fixing Drills DRAWING NUMBER: ID-1200T/TS TITLE:
DATE: 05/01/16 INSTALLATION DRAWING
300
300
4
6
Bottom View
Iso View(Bottom)
310
185
CEILING WALL
Installation Options
6 1 OUTLET B203057EHTC
1 1 THERMOCONNECTOR BTHC
81.4
Quantity
Position
Type /
Denomination
41.4
DWG. Number
PART LIST
300
2
6
Bottom View 4
Iso View(Bottom)
310
185
CEILING WALL
Installation Options
6 1 OUTLET B203057EHTC
5 1 BRACKET B122030BRKT
35 235 35 4 2 EXTERNAL HOUSING BRACKET SUPPORT BAEHBS
3 1 GENERATOR B20TAS
Type /
Denomination
40
DWG. Number
PART LIST
41.4
300
4
6
Bottom View
Iso View(Bottom)
310
185
CEILING WALL
Installation Options
6 1 OUTLET B203057EHTC
1 1 THERMOCONNECTOR BTHC
81.4
Quantity
Position
Type /
Denomination
41.4
DWG. Number
PART LIST
300
2
6
Bottom View 4
Iso View(Bottom)
310
185
CEILING WALL
Installation Options
6 1 OUTLET B203057EHTC
5 1 BRACKET B122030BRKT
35 235 35 4 2 EXTERNAL HOUSING BRACKET SUPPORT BAEHBS
3 1 GENERATOR B30TAS
Type /
Denomination
40
DWG. Number
PART LIST
41.4
300
5
Bottom View
Iso View(Bottom)
415
300
CEILING WALL
Installation Options
305.0
5 2 BOLT FOR BRACKET SUPPORT BABBS
35.0 235.0 35.0 4 1 BRACKET B57BRKT
3 1 GENERATOR B42AS
Quantity
Position
Type /
Denomination
71.4
DWG. Number
PART LIST
FirePro Systems Ltd FP-4200T
Condensed aerosol generator FP-4200TS
Fixing Drills DRAWING NUMBER: ID-4200T/TS TITLE:
DATE: 02/10/14 INSTALLATION DRAWING
300
300
4
Bottom View
Iso View(Bottom)
415
300
CEILING WALL
Installation Options
6 1 OUTLET B203057EHTC
305.0
5 1 BRACKET B57BRKT
35.0 235.0 35.0 4 1 EXTERNAL HOUSING BRACKET SUPPORT BAEHBS
3 1 HOUSING B57EHSW
1 1 THERMOCONNECTOR BTHC
111.4
Quantity
Position
Type /
Denomination
71.4
DWG. Number
PART LIST
FirePro Systems Ltd FP-5700
Condensed aerosol generator FP-5700S
Fixing Drills DRAWING NUMBER: ID-5700/S TITLE:
DATE: 15/04/10 INSTALLATION DRAWING
300
300
5
Bottom View
Iso View(Bottom)
415
300
CEILING WALL
Installation Options
305.0
5 2 BOLT FOR BRACKET SUPPORT BABBS
35.0 235.0 35.0 4 1 BRACKET B57BRKT
3 1 GENERATOR B57TAS
Quantity
Position
Type /
Denomination
71.4
DWG. Number
PART LIST
FirePro Systems Ltd FP-5700T
Condensed aerosol generator FP-5700TS
Fixing Drills DRAWING NUMBER: ID-5700T/TS TITLE:
DATE: 05/01/16 INSTALLATION DRAWING