Professional Documents
Culture Documents
Issue / Amendment
Description
Rev. Date
No.
0 07.01.2022 First Issue
Contract J110,
DOC. NO. : J110/DES/00135/-
Design & Construction of Jurong East Station & Viaduct
REV. NO. : 0
Including Addition & Alteration Works to the Existing
SHEET : 3 of 20
Jurong East Station for Jurong Region Line
FINAL STRUCTURAL ANALYSIS AND CALCULATION FOR
A&A WORKS AT SOUTHSIDE STAIRCASE
TABLE OF CONTENTS
1.0 INTRODUCTION .......................................................................................................................... 4
1.1 PROJECT DESCRIPTION AND SCOPE ............................................................................................................ 4
1.2 OBJECTIVES .......................................................................................................................................... 5
2.0 SITE DETAILS ............................................................................................................................... 7
2.1 ADJACENT STRUCTURES/ BUILDINGS ......................................................................................................... 7
3.0 PROPOSED STRUCTURE .............................................................................................................. 8
3.1 DESCRIPTION OF STRUCTURE ................................................................................................................... 8
3.1.1 JE5 Station ........................................................................................................................................ 8
3.2 Interface Between JE5 Station and Viaduct ................................................................................... 10
3.3 Provision for Future Development .................................................................................................. 11
4.0 STRUCTURAL SCHEMATIC ......................................................................................................... 13
4.1 FUNCTIONAL FRAMING......................................................................................................................... 13
4.2 LOAD TRANSFER AND LOAD PATH........................................................................................................... 13
4.2.1 Vertical Loads ................................................................................................................................. 13
4.2.2 Horizontal Loads............................................................................................................................. 13
4.3 STABILITY CONSIDERATION .................................................................................................................... 15
5.0 DESIGN CRITERIA & STANDARDS .............................................................................................. 16
6.0 DESIGN OF JE5 PILING .............................................................................................................. 16
List of Appendices
Appendix A Southern Staircase Structure Analysis and Design
Appendix B Check List Form A1 & A2
Appendix C Southern Staircase Piling Analysis and Design
Appendix D Check List Form for Piling A1 & A2
Contract J110,
DOC. NO. : J110/DES/00135/-
Design & Construction of Jurong East Station & Viaduct
REV. NO. : 0
Including Addition & Alteration Works to the Existing
SHEET : 4 of 20
Jurong East Station for Jurong Region Line
FINAL STRUCTURAL ANALYSIS AND CALCULATION FOR
A&A WORKS AT SOUTHSIDE STAIRCASE
1.0 INTRODUCTION
AECOM Singapore Pte Ltd has been appointed by DAELIM Industrial Co. Ltd. to provide
engineering consultancy services for Contract J110 design and construction of Jurong East
Station and Viaduct including Addition and Alteration works to the existing Jurong East
station for Jurong Region Line.
Contract J110 comprises the design and construction of proposed elevated JRL Jurong East
Station (JE5) adjacent to the existing North South Line (NSL) and East West Line (EWL)
Jurong East Station (JUR) (Figure 1.2), Addition and Alteration (A&A) works to the existing
JUR Station to integration with JRL Station, and associated elevated viaducts.
1.2 OBJECTIVES
This design report presents piling works of the new JE5 station (Figure 1.3).
The foundation design parameters for bored piles greater than 450mm diameter are
verified from 600mm diameter load test pile ULT-01 and those for bored piles less than or
equal to 450mm diameter are verified from 450mm diameter load test pile ULT-03. The
foundation design parameters adopted for geotechnical design of piling work under this
submission are summarized in Table 1.1 and Table 1.2.
Table 1.1 Foundation Design Parameters for Bored Pile > 450mm diameter
Contract J110,
DOC. NO. : J110/DES/00135/-
Design & Construction of Jurong East Station & Viaduct
REV. NO. : 0
Including Addition & Alteration Works to the Existing
SHEET : 6 of 20
Jurong East Station for Jurong Region Line
FINAL STRUCTURAL ANALYSIS AND CALCULATION FOR
A&A WORKS AT SOUTHSIDE STAIRCASE
Table 1.2 Foundation Design Parameters for Bored Pile < 450mm diameter
Contract J110,
DOC. NO. : J110/DES/00135/-
Design & Construction of Jurong East Station & Viaduct
REV. NO. : 0
Including Addition & Alteration Works to the Existing
SHEET : 7 of 20
Jurong East Station for Jurong Region Line
FINAL STRUCTURAL ANALYSIS AND CALCULATION FOR
A&A WORKS AT SOUTHSIDE STAIRCASE
It has been understood that there will be a future development, Jurong Hub (JH) to the
north of the JE5 Station. However, information such as the structural outline of the future
development is not available at this stage.
N
N
The proposed JE5 Station is a four storey structure (Figure 3.2 & 3.3). The column grids are
spaced at 12.5m c/c longitudinally. The building height of approximately 28m from the
ground level to roof top. Conventional cast in-situ RC beams, RC columns & walls and most
of slabs are proposed to form a rigid frame to resist vertical and horizontal wind & notional
loads. Composite slab with composite steel beam is proposed at the platform level that
interfaced between JE5 and JUR Station to minimize the impact to the train operation of
the existing MRT lines during construction. Steel structural framing system is adopted for
the proposed roof.
Deep Foundation Elements (DFE) consisting of bored are provided underneath the RC
columns and walls. Loads are transferred from floors to the vertical load bearing walls /
columns before landed to DFEs. At area adjacent to and below the existing station along
GL JRL-J.B, small diameter bored piles are proposed to avoid, and minimize impact to the
Contract J110,
DOC. NO. : J110/DES/00135/-
Design & Construction of Jurong East Station & Viaduct
REV. NO. : 0
Including Addition & Alteration Works to the Existing
SHEET : 9 of 20
Jurong East Station for Jurong Region Line
FINAL STRUCTURAL ANALYSIS AND CALCULATION FOR
A&A WORKS AT SOUTHSIDE STAIRCASE
existing structures, headroom, clearance, site constraints, existing viaduct structure during
piles installation. The layout plan (Figure 3.2) and typical section (Figure 3.3) as shown
below.
The south side viaduct is supported by JE5 Station beam with bearings at GL JRL J13 at Lower under
platform level and upper under platform level as shown in (Figure 3.6) between GL JRL JC & JRL JD.
The north side viaduct is supported by JE5 Station beam with bearings at GL JRL J1 at Lower under
platform level and upper under platform level as shown in (Figure 3.7) between GL JRL JC & JRL JD.
Figure 3.7 : North Side Viaducts Between J110/ J120 to JE5 Station
Two numbers of 12m width future link bridge toward J-cube is future development and will be connected
at JE5 station concourse level at GLJRL-JD / GLJRL-J1 to J2 OR GLJRL-JD / GLJRL-J2 to J3 as shown
in figure 3.9 and GLJRL-JD / GLJRL-J11 to J12. As shown in Figure 3.10. structural provision for link
bridge is provided as per the information as mention below.
Loads acted on the structure at JRL station concourse level is assumed to be 2600kN
SLS loading based on 12m width and 15m span bridge (half of the span to be loaded
on JRL station side)
Figure: 3.8: Future Link Bridge Connection between (GL JRL J.1 to J.2 OR GL JRL J.2 to J.3) AND (GL
JRL J.11 to J.12) at JE5 Station Concourse Level
Figure: 3.9: Future Link Bridge Connection between GL JRL J.1 to J.2 OR GL JRL J.2 to J.3 (at JE5 Station
Concourse Level)
Contract J110,
DOC. NO. : J110/DES/00135/-
Design & Construction of Jurong East Station & Viaduct
REV. NO. : 0
Including Addition & Alteration Works to the Existing
SHEET : 12 of 20
Jurong East Station for Jurong Region Line
FINAL STRUCTURAL ANALYSIS AND CALCULATION FOR
A&A WORKS AT SOUTHSIDE STAIRCASE
Figure: 3.10: Future Link Bridge Connection Between GL JRL J.11 to J.12 (at JE5 Station Concourse Level)
Station Concourse Level)
Contract J110,
DOC. NO. : J110/DES/00135/-
Design & Construction of Jurong East Station & Viaduct
REV. NO. : 0
Including Addition & Alteration Works to the Existing
SHEET : 13 of 20
Jurong East Station for Jurong Region Line
FINAL STRUCTURAL ANALYSIS AND CALCULATION FOR
A&A WORKS AT SOUTHSIDE STAIRCASE
The structural framing for JE5 Station consists of the combination of conventional cast in-
situ beam/ slab, flat slabs and composite slabs supported on RC columns which braced by
RC beams in both directions to improve the structural robustness. Steel beams with purlins
are adopted for the roof structure.
The gravity and lateral load imposed on the superstructure are typically braced and
transferred to piled foundation via pilecaps or ground beams to foundation.
The basic structural vertical load path of JE5 Station is shown in Figure 4.1.
The gravitational forces emanating from permanent load, imposed load on the roof and the
vertical load arising from wind load component acting on the roof are transferred to the
columns and walls through steel beams & purlins by bending and shear actions. Likewise,
the gravitational forces arising from permanent load and imposed load on other functional
floors are supported on slabs that transfer the loads to beams through bending and shear
actions. The beams in turn transfer the loads to columns and walls through bending and
shear actions.
The columns and walls via compression and bending actions transfer the loads to pile caps.
Pile caps then transfer the loads to DFEs through bending and shear actions. DFEs transfer
the loads to the ground by skin friction and end bearing actions.
The basic structural horizontal load path of JE5 Station is presented in Figure 4.2.
Contract J110,
DOC. NO. : J110/DES/00135/-
Design & Construction of Jurong East Station & Viaduct
REV. NO. : 0
Including Addition & Alteration Works to the Existing
SHEET : 14 of 20
Jurong East Station for Jurong Region Line
FINAL STRUCTURAL ANALYSIS AND CALCULATION FOR
A&A WORKS AT SOUTHSIDE STAIRCASE
Lateral wind load and Equivalent Horizontal Force (EHF) are transferred through façade
elements to the floors and roof by bending and shear actions. Diaphragm action of the
floors (slabs & beams) and roof (purlins & beams) transfers the load to walls and columns
through compression and bending actions. The structural frame comprising walls and
columns resists the wind forces and transfer them by bending and shear actions to the pile
caps supported on DFEs that transfer the loads to the ground by subgrade reactions of soil.
Equivalent Horizontal Force (EHF) shall be applied at each floor as shown in below diagram,
figure 4.2.
According to the latest layout, the topmost habitable structural floor level is Upper
Platform. The building height, according to BC3-2013, is 19.99m from Ground Level (SSL
9.875) to Upper Platform Level (SSL 29.865) which is less than 20m. Seismic action is not
necessary to consider in the design.
DFEs are proposed to support the JE5 Station. Global vertical stability is achieved through
skin friction and end bearing resistance from the soil onto the DFEs. Global lateral stability
is achieved by subgrade reactions of the soil resisted bending and shear actions of the DFEs.
The overturning due to lateral load will be resisted by push and pull effects from the DFEs
and structure self-weight. Owning to the regular geometry of this building and no basement
works involved, the DFEs are unlikely to be in tension. The structure loads are carried down
to the stiff ground layer through the DFEs, to minimize settlement of structures.
Contract J110,
DOC. NO. : J110/DES/00135/-
Design & Construction of Jurong East Station & Viaduct
REV. NO. : 0
Including Addition & Alteration Works to the Existing
SHEET : 16 of 20
Jurong East Station for Jurong Region Line
FINAL STRUCTURAL ANALYSIS AND CALCULATION FOR
A&A WORKS AT SOUTHSIDE STAIRCASE
Details of design criteria, standards, specification and relevant information can be referred
to the following document.
AIP A3-2 for Station & Hub Plaza Structure Document no: DOC/J110/DCS/DR/1005
3D FEM model was used to obtain pile loads. We have included the super structural framing
in Appendix A as reference only in this piling submission. The formal submission for the
super structures will be made in our upcoming JE5 superstructure submission. The loadings
extracted from the model are also summarized in Appendix A, which is the basis of our pile
design. The detailed design for structural and geotechnical capacity of piling is also attached
in Appendix A.
The piled foundation included pile size ranged from 450mm, 900mm to 1000mm. 450mm
diameter piles have been proposed to minimize impact to adjacent existing station.
Contract J110,
DOC. NO. : J110/DES/00135/-
Design & Construction of Jurong East Station & Viaduct
REV. NO. : 0
Including Addition & Alteration Works to the Existing
SHEET : 17 of 20
Jurong East Station for Jurong Region Line
FINAL STRUCTURAL ANALYSIS AND CALCULATION FOR
A&A WORKS AT SOUTHSIDE STAIRCASE
APPENDIX A
1 Structure Data
This chapter provides model geometry information, including items such as story levels, point coordinates, and
element connectivity.
2 Loads
This chapter provides loading information as applied to the model.
2.1 Load Patterns
Table 2.1 - Load Pattern Definitions
Self
Is Auto
Name Type Weight Auto Load
Load
Multiplier
~LLRF Yes Other 0
Acci Fx No Other 0
Acci Fy No Other 0
DL No Dead 1
LL No Live 0
NxDL No Notional 0 Auto
NxSDL No Notional 0 Auto
NyDL No Notional 0 Auto
NySDL No Notional 0 Auto
SDL No Super Dead 0
WIND No Wind 0 EUROCODE1 2005
WIND(1/2) Yes Wind 0 EUROCODE1 2005
WIND(2/2) Yes Wind 0 EUROCODE1 2005
Name Type
Modal Modal - Eigen
DL Linear Static
SDL Linear Static
LL Linear Static
Acci Fx Linear Static
Acci Fy Linear Static
WIND Linear Static
NL-0deg Linear Static
NL-90deg Linear Static
NL-180deg Linear Static
NL-270deg Linear Static
3 Analysis Results
This chapter provides analysis results.
3.1 Structure Results
Table 3.1 - Base Reactions
Step FX FY FZ MX MY MZ X Y Z
Output Case Case Type
Type kN kN kN kN-m kN-m kN-m m m m
DL LinStatic 0 0 37075.5 889603.61 -226047.81 -0.01 0 0 -20
Step FX FY FZ MX MY MZ X Y Z
Output Case Case Type
Type kN kN kN kN-m kN-m kN-m m m m
SLS 3 Combination Min 0 0 56721.5 1383548.14 -313771.94 -0.02 0 0 -20
Step FX FY FZ MX MY MZ X Y Z
Output Case Case Type
Type kN kN kN kN-m kN-m kN-m m m m
Set B-ENVE Combination Max 721.02 721.02 83435.27 2059527.01 -249067.15 17534.52 0 0 -20
Set B-ENVE Combination Min -721.02 -721.02 48067.68 1147362.04 -479368.01 -17534.56 0 0 -20
Step FX FY FZ MX MY MZ X Y Z
Output Case Case Type
Type kN kN kN kN-m kN-m kN-m m m m
Set C- ENVE Combination Max 721.02 721.02 64139.06 1589079.71 -249067.15 17534.52 0 0 -20
Set C- ENVE Combination Min -721.02 -721.02 48067.68 1147362.04 -372318.87 -17534.55 0 0 -20
Step X Y Z
Story Output Case Case Type Direction Drift Label
Type m m m
Upper Platform DL LinStatic X 1.6E-05 83 13.56 40.4 18.82
Upper Platform DL LinStatic Y 2.2E-05 391 4.75 34.72 18.82
Upper Platform SDL LinStatic X 8E-06 83 13.56 40.4 18.82
Upper Platform SDL LinStatic Y 9E-06 391 4.75 34.72 18.82
Upper Platform LL LinStatic X 8E-06 83 13.56 40.4 18.82
Upper Platform LL LinStatic Y 9E-06 391 4.75 34.72 18.82
Upper Platform Acci Fx LinStatic X 2.995E-07 76 13.56 35.22 18.82
Upper Platform Acci Fx LinStatic Y 1E-06 389 4.75 40.4 18.82
Upper Platform Acci Fy LinStatic X 1E-06 16 13.56 5 18.82
Upper Platform Acci Fy LinStatic Y 2E-06 389 4.75 40.4 18.82
Upper Platform NL-0deg LinStatic X 4E-06 16 13.56 5 18.82
Upper Platform NL-90deg LinStatic Y 1E-05 389 4.75 40.4 18.82
Upper Platform NL-180deg LinStatic X 4E-06 16 13.56 5 18.82
Upper Platform NL-270deg LinStatic Y 1E-05 389 4.75 40.4 18.82
Upper Platform Set B -UDCon1 Combination X 3.2E-05 83 13.56 40.4 18.82
Upper Platform Set B -UDCon1 Combination Y 4.2E-05 391 4.75 34.72 18.82
Upper Platform SLS 1 Combination X 3.2E-05 83 13.56 40.4 18.82
Upper Platform SLS 1 Combination Y 4E-05 391 4.75 34.72 18.82
Upper Platform ALL DL Combination X 2.4E-05 83 13.56 40.4 18.82
Upper Platform ALL DL Combination Y 3.1E-05 391 4.75 34.72 18.82
Upper Platform ALL LL Combination X 8E-06 83 13.56 40.4 18.82
Upper Platform ALL LL Combination Y 9E-06 391 4.75 34.72 18.82
Upper Platform ULS-A1 Combination X 2.7E-05 83 13.56 40.4 18.82
Upper Platform ULS-A1 Combination Y 3.5E-05 391 4.75 34.72 18.82
Upper Platform ULS-A2 Combination X 2.7E-05 83 13.56 40.4 18.82
Upper Platform ULS-A2 Combination Y 3.3E-05 391 4.75 34.72 18.82
Upper Platform DCmpD1 Combination X 2.4E-05 83 13.56 40.4 18.82
Upper Platform DCmpD1 Combination Y 3.1E-05 391 4.75 34.72 18.82
Upper Platform DCmpD2 Combination X 3.2E-05 83 13.56 40.4 18.82
Upper Platform DCmpD2 Combination Y 4E-05 391 4.75 34.72 18.82
Upper Platform DCmpS1 Combination X 3.2E-05 83 13.56 40.4 18.82
Upper Platform DCmpS1 Combination Y 4.2E-05 391 4.75 34.72 18.82
Step X Y Z
Story Output Case Case Type Direction Drift Label
Type m m m
Upper Platform DCmpS2 Combination X 4.4E-05 83 13.56 40.4 18.82
Upper Platform DCmpS2 Combination Y 5.6E-05 391 4.75 34.72 18.82
Upper Platform DCmpC1 Combination X 2.4E-05 83 13.56 40.4 18.82
Upper Platform DCmpC1 Combination Y 3.3E-05 391 4.75 34.72 18.82
Upper Platform Geo-Com1 Combination X 4.4E-05 83 13.56 40.4 18.82
Upper Platform Geo-Com1 Combination Y 5.6E-05 391 4.75 34.72 18.82
Upper Platform Geo-Com2 Combination X 3.4E-05 83 13.56 40.4 18.82
Upper Platform Geo-Com2 Combination Y 4.3E-05 391 4.75 34.72 18.82
Upper Platform SLS 2 Combination Max X 3.2E-05 83 13.56 40.4 18.82
Upper Platform SLS 2 Combination Max Y 4E-05 391 4.75 34.72 18.82
Upper Platform SLS 2 Combination Min X 3.2E-05 83 13.56 40.4 18.82
Upper Platform SLS 2 Combination Min Y 4E-05 391 4.75 34.72 18.82
Upper Platform SLS 3 Combination Max X 2.9E-05 83 13.56 40.4 18.82
Upper Platform SLS 3 Combination Max Y 3.7E-05 391 4.75 34.72 18.82
Upper Platform SLS 3 Combination Min X 2.9E-05 83 13.56 40.4 18.82
Upper Platform SLS 3 Combination Min Y 3.7E-05 391 4.75 34.72 18.82
Upper Platform SLS 4 Combination Max X 2.4E-05 83 13.56 40.4 18.82
Upper Platform SLS 4 Combination Max Y 3.1E-05 391 4.75 34.72 18.82
Upper Platform SLS 4 Combination Min X 2.4E-05 83 13.56 40.4 18.82
Upper Platform SLS 4 Combination Min Y 3.1E-05 391 4.75 34.72 18.82
Upper Platform SLS ENVE Combination Max X 2.4E-05 83 13.56 40.4 18.82
Upper Platform SLS ENVE Combination Max Y 4E-05 391 4.75 34.72 18.82
Upper Platform SLS ENVE Combination Min X 3.2E-05 83 13.56 40.4 18.82
Upper Platform SLS ENVE Combination Min Y 3.1E-05 391 4.75 34.72 18.82
Upper Platform Set B -UDCon2 Combination X 4.4E-05 83 13.56 40.4 18.82
Upper Platform Set B -UDCon2 Combination Y 5.6E-05 391 4.75 34.72 18.82
Upper Platform Set B -UDCon3 Combination Max X 4.4E-05 83 13.56 40.4 18.82
Upper Platform Set B -UDCon3 Combination Max Y 5.6E-05 391 4.75 34.72 18.82
Upper Platform Set B -UDCon3 Combination Min X 4.4E-05 83 13.56 40.4 18.82
Upper Platform Set B -UDCon3 Combination Min Y 5.6E-05 391 4.75 34.72 18.82
Upper Platform Set B -UDCon4 Combination Max X 4.1E-05 83 13.56 40.4 18.82
Upper Platform Set B -UDCon4 Combination Max Y 5.2E-05 391 4.75 34.72 18.82
Upper Platform Set B -UDCon4 Combination Min X 4.1E-05 83 13.56 40.4 18.82
Upper Platform Set B -UDCon4 Combination Min Y 5.2E-05 391 4.75 34.72 18.82
Upper Platform Set B -UDCon5 Combination Max X 3.2E-05 83 13.56 40.4 18.82
Upper Platform Set B -UDCon5 Combination Max Y 4.2E-05 391 4.75 34.72 18.82
Upper Platform Set B -UDCon5 Combination Min X 3.2E-05 83 13.56 40.4 18.82
Upper Platform Set B -UDCon5 Combination Min Y 4.2E-05 391 4.75 34.72 18.82
Upper Platform Set B -UDCon6 Combination Max X 2.4E-05 83 13.56 40.4 18.82
Upper Platform Set B -UDCon6 Combination Max Y 3.1E-05 391 4.75 34.72 18.82
Upper Platform Set B -UDCon6 Combination Min X 2.4E-05 83 13.56 40.4 18.82
Upper Platform Set B -UDCon6 Combination Min Y 3.1E-05 391 4.75 34.72 18.82
Upper Platform Set B -UDCon7-1 Combination X 4.6E-05 83 13.56 40.4 18.82
Upper Platform Set B -UDCon7-1 Combination Y 5.6E-05 391 4.75 34.72 18.82
Upper Platform Set B -UDCon7-2 Combination X 4.3E-05 83 13.56 40.4 18.82
Step X Y Z
Story Output Case Case Type Direction Drift Label
Type m m m
Upper Platform Set B -UDCon7-2 Combination Y 4.6E-05 391 4.75 34.72 18.82
Upper Platform Set B -UDCon7-3 Combination X 4.2E-05 83 13.56 40.4 18.82
Upper Platform Set B -UDCon7-3 Combination Y 5.6E-05 391 4.75 34.72 18.82
Upper Platform Set B -UDCon7-4 Combination X 4.5E-05 83 13.56 40.4 18.82
Upper Platform Set B -UDCon7-4 Combination Y 6.5E-05 391 4.75 34.72 18.82
Upper Platform Set B -UDCon8-1 Combination X 4.2E-05 83 13.56 40.4 18.82
Upper Platform Set B -UDCon8-1 Combination Y 5.2E-05 391 4.75 34.72 18.82
Upper Platform Set B -UDCon8-2 Combination X 3.9E-05 83 13.56 40.4 18.82
Upper Platform Set B -UDCon8-2 Combination Y 4.2E-05 391 4.75 34.72 18.82
Upper Platform Set B -UDCon8-3 Combination X 3.9E-05 83 13.56 40.4 18.82
Upper Platform Set B -UDCon8-3 Combination Y 5.1E-05 391 4.75 34.72 18.82
Upper Platform Set B -UDCon8-4 Combination X 4.2E-05 83 13.56 40.4 18.82
Upper Platform Set B -UDCon8-4 Combination Y 6.1E-05 391 4.75 34.72 18.82
Upper Platform Set B -UDCon9-1 Combination X 3.4E-05 83 13.56 40.4 18.82
Upper Platform Set B -UDCon9-1 Combination Y 4.2E-05 391 4.75 34.72 18.82
Upper Platform Set B -UDCon9-2 Combination X 3.1E-05 83 13.56 40.4 18.82
Upper Platform Set B -UDCon9-2 Combination Y 3.2E-05 391 4.75 34.72 18.82
Upper Platform Set B -UDCon9-3 Combination X 3E-05 83 13.56 40.4 18.82
Upper Platform Set B -UDCon9-3 Combination Y 4.2E-05 391 4.75 34.72 18.82
Upper Platform Set B -UDCon9-4 Combination X 3.3E-05 83 13.56 40.4 18.82
Upper Platform Set B -UDCon9-4 Combination Y 5.1E-05 391 4.75 34.72 18.82
Upper Platform Set B -UDCon10-1 Combination X 2.6E-05 83 13.56 40.4 18.82
Upper Platform Set B -UDCon10-1 Combination Y 3.1E-05 391 4.75 34.72 18.82
Upper Platform Set B -UDCon10-2 Combination X 2.3E-05 83 13.56 40.4 18.82
Upper Platform Set B -UDCon10-2 Combination Y 2.2E-05 391 4.75 34.72 18.82
Upper Platform Set B -UDCon10-3 Combination X 2.2E-05 83 13.56 40.4 18.82
Upper Platform Set B -UDCon10-3 Combination Y 3.1E-05 391 4.75 34.72 18.82
Upper Platform Set B -UDCon10-4 Combination X 2.5E-05 83 13.56 40.4 18.82
Upper Platform Set B -UDCon10-4 Combination Y 4E-05 391 4.75 34.72 18.82
Upper Platform Set B-ENVE Combination Max Y 6.5E-05 391 4.75 34.72 18.82
Upper Platform Set B-ENVE Combination Min X 4.6E-05 83 13.56 40.4 18.82
Upper Platform Set B-ENVE Combination Min Y 2.2E-05 391 4.75 34.72 18.82
Upper Platform Set C -UDCon1 Combination X 2.4E-05 83 13.56 40.4 18.82
Upper Platform Set C -UDCon1 Combination Y 3.1E-05 391 4.75 34.72 18.82
Upper Platform Set C -UDCon2 Combination X 3.4E-05 83 13.56 40.4 18.82
Upper Platform Set C -UDCon2 Combination Y 4.3E-05 391 4.75 34.72 18.82
Upper Platform Set C -UDCon3 Combination Max X 3.4E-05 83 13.56 40.4 18.82
Upper Platform Set C -UDCon3 Combination Max Y 4.3E-05 391 4.75 34.72 18.82
Upper Platform Set C -UDCon3 Combination Min X 3.4E-05 83 13.56 40.4 18.82
Upper Platform Set C -UDCon3 Combination Min Y 4.3E-05 391 4.75 34.72 18.82
Upper Platform Set C -UDCon4 Combination Max X 3.1E-05 83 13.56 40.4 18.82
Upper Platform Set C -UDCon4 Combination Max Y 3.9E-05 391 4.75 34.72 18.82
Upper Platform Set C -UDCon4 Combination Min X 3.1E-05 83 13.56 40.4 18.82
Upper Platform Set C -UDCon4 Combination Min Y 3.9E-05 391 4.75 34.72 18.82
Upper Platform Set C -UDCon5 Combination Max X 2.4E-05 83 13.56 40.4 18.82
Step X Y Z
Story Output Case Case Type Direction Drift Label
Type m m m
Upper Platform Set C -UDCon5 Combination Max Y 3.1E-05 391 4.75 34.72 18.82
Upper Platform Set C -UDCon5 Combination Min X 2.4E-05 83 13.56 40.4 18.82
Upper Platform Set C -UDCon5 Combination Min Y 3.1E-05 391 4.75 34.72 18.82
Upper Platform Set C -UDCon6-1 Combination X 3.6E-05 83 13.56 40.4 18.82
Upper Platform Set C -UDCon6-1 Combination Y 4.3E-05 391 4.75 34.72 18.82
Upper Platform Set C -UDCon6-2 Combination X 3.3E-05 83 13.56 40.4 18.82
Upper Platform Set C -UDCon6-2 Combination Y 3.4E-05 391 4.75 34.72 18.82
Upper Platform Set C -UDCon6-3 Combination X 3.2E-05 83 13.56 40.4 18.82
Upper Platform Set C -UDCon6-3 Combination Y 4.3E-05 391 4.75 34.72 18.82
Upper Platform Set C -UDCon6-4 Combination X 3.5E-05 83 13.56 40.4 18.82
Upper Platform Set C -UDCon6-4 Combination Y 5.2E-05 391 4.75 34.72 18.82
Upper Platform Set C -UDCon7-1 Combination X 3.3E-05 83 13.56 40.4 18.82
Upper Platform Set C -UDCon7-1 Combination Y 4E-05 391 4.75 34.72 18.82
Upper Platform Set C -UDCon7-2 Combination X 3E-05 83 13.56 40.4 18.82
Upper Platform Set C -UDCon7-2 Combination Y 3E-05 391 4.75 34.72 18.82
Upper Platform Set C -UDCon7-3 Combination X 2.9E-05 83 13.56 40.4 18.82
Upper Platform Set C -UDCon7-3 Combination Y 3.9E-05 391 4.75 34.72 18.82
Upper Platform Set C -UDCon7-4 Combination X 3.2E-05 83 13.56 40.4 18.82
Upper Platform Set C -UDCon7-4 Combination Y 4.9E-05 391 4.75 34.72 18.82
Upper Platform Set C -UDCon8-1 Combination X 2.6E-05 83 13.56 40.4 18.82
Upper Platform Set C -UDCon8-1 Combination Y 3.1E-05 391 4.75 34.72 18.82
Upper Platform Set C -UDCon8-2 Combination X 2.3E-05 83 13.56 40.4 18.82
Upper Platform Set C -UDCon8-2 Combination Y 2.2E-05 391 4.75 34.72 18.82
Upper Platform Set C -UDCon8-3 Combination X 2.2E-05 83 13.56 40.4 18.82
Upper Platform Set C -UDCon8-3 Combination Y 3.1E-05 391 4.75 34.72 18.82
Upper Platform Set C -UDCon8-4 Combination X 2.5E-05 83 13.56 40.4 18.82
Upper Platform Set C -UDCon8-4 Combination Y 4E-05 391 4.75 34.72 18.82
Upper Platform Set C- ENVE Combination Max Y 5.2E-05 391 4.75 34.72 18.82
Upper Platform Set C- ENVE Combination Min X 3.6E-05 83 13.56 40.4 18.82
Upper Platform Set C- ENVE Combination Min Y 2.2E-05 391 4.75 34.72 18.82
Lower Platform DL LinStatic X 1.1E-05 83 13.56 40.4 15.79
Lower Platform DL LinStatic Y 1.5E-05 16 13.56 5 15.79
Lower Platform SDL LinStatic X 6E-06 83 13.56 40.4 15.79
Lower Platform SDL LinStatic Y 6E-06 16 13.56 5 15.79
Lower Platform LL LinStatic X 8E-06 83 13.56 40.4 15.79
Lower Platform LL LinStatic Y 7E-06 16 13.56 5 15.79
Lower Platform Acci Fx LinStatic X 3.998E-07 74 5 35.22 15.79
Lower Platform Acci Fx LinStatic Y 1E-06 42 13.56 19.85 15.79
Lower Platform Acci Fy LinStatic Y 2E-06 24 5 10.18 15.79
Lower Platform NL-0deg LinStatic X 6E-06 15 5 5 15.79
Lower Platform NL-90deg LinStatic Y 1.2E-05 24 5 10.18 15.79
Lower Platform NL-180deg LinStatic X 6E-06 15 5 5 15.79
Lower Platform NL-270deg LinStatic Y 1.2E-05 24 5 10.18 15.79
Lower Platform Set B -UDCon1 Combination X 2.3E-05 83 13.56 40.4 15.79
Lower Platform Set B -UDCon1 Combination Y 2.8E-05 16 13.56 5 15.79
Step X Y Z
Story Output Case Case Type Direction Drift Label
Type m m m
Lower Platform SLS 1 Combination X 2.5E-05 83 13.56 40.4 15.79
Lower Platform SLS 1 Combination Y 2.8E-05 16 13.56 5 15.79
Lower Platform ALL DL Combination X 1.7E-05 83 13.56 40.4 15.79
Lower Platform ALL DL Combination Y 2.1E-05 16 13.56 5 15.79
Lower Platform ALL LL Combination X 8E-06 83 13.56 40.4 15.79
Lower Platform ALL LL Combination Y 7E-06 16 13.56 5 15.79
Lower Platform ULS-A1 Combination X 2.1E-05 83 13.56 40.4 15.79
Lower Platform ULS-A1 Combination Y 2.4E-05 16 13.56 5 15.79
Lower Platform ULS-A2 Combination X 2E-05 83 13.56 40.4 15.79
Lower Platform ULS-A2 Combination Y 2.2E-05 16 13.56 5 15.79
Lower Platform DCmpD1 Combination X 1.7E-05 83 13.56 40.4 15.79
Lower Platform DCmpD1 Combination Y 2.1E-05 16 13.56 5 15.79
Lower Platform DCmpD2 Combination X 2.5E-05 83 13.56 40.4 15.79
Lower Platform DCmpD2 Combination Y 2.8E-05 16 13.56 5 15.79
Lower Platform DCmpS1 Combination X 2.3E-05 83 13.56 40.4 15.79
Lower Platform DCmpS1 Combination Y 2.8E-05 16 13.56 5 15.79
Lower Platform DCmpS2 Combination X 3.5E-05 83 13.56 40.4 15.79
Lower Platform DCmpS2 Combination Y 3.9E-05 16 13.56 5 15.79
Lower Platform DCmpC1 Combination X 1.7E-05 83 13.56 40.4 15.79
Lower Platform DCmpC1 Combination Y 2.3E-05 16 13.56 5 15.79
Lower Platform Geo-Com1 Combination X 3.5E-05 83 13.56 40.4 15.79
Lower Platform Geo-Com1 Combination Y 3.9E-05 16 13.56 5 15.79
Lower Platform Geo-Com2 Combination X 2.8E-05 83 13.56 40.4 15.79
Lower Platform Geo-Com2 Combination Y 3E-05 16 13.56 5 15.79
Lower Platform SLS 2 Combination Max X 2.5E-05 83 13.56 40.4 15.79
Lower Platform SLS 2 Combination Max Y 2.8E-05 16 13.56 5 15.79
Lower Platform SLS 2 Combination Min X 2.5E-05 83 13.56 40.4 15.79
Lower Platform SLS 2 Combination Min Y 2.8E-05 16 13.56 5 15.79
Lower Platform SLS 3 Combination Max X 2.3E-05 83 13.56 40.4 15.79
Lower Platform SLS 3 Combination Max Y 2.6E-05 16 13.56 5 15.79
Lower Platform SLS 3 Combination Min X 2.3E-05 83 13.56 40.4 15.79
Lower Platform SLS 3 Combination Min Y 2.6E-05 16 13.56 5 15.79
Lower Platform SLS 4 Combination Max X 1.7E-05 83 13.56 40.4 15.79
Lower Platform SLS 4 Combination Max Y 2.1E-05 16 13.56 5 15.79
Lower Platform SLS 4 Combination Min X 1.7E-05 83 13.56 40.4 15.79
Lower Platform SLS 4 Combination Min Y 2.1E-05 16 13.56 5 15.79
Lower Platform SLS ENVE Combination Max X 1.7E-05 83 13.56 40.4 15.79
Lower Platform SLS ENVE Combination Max Y 2.8E-05 16 13.56 5 15.79
Lower Platform SLS ENVE Combination Min X 2.5E-05 83 13.56 40.4 15.79
Lower Platform SLS ENVE Combination Min Y 2.1E-05 16 13.56 5 15.79
Lower Platform Set B -UDCon2 Combination X 3.5E-05 83 13.56 40.4 15.79
Lower Platform Set B -UDCon2 Combination Y 3.9E-05 16 13.56 5 15.79
Lower Platform Set B -UDCon3 Combination Max X 3.5E-05 83 13.56 40.4 15.79
Lower Platform Set B -UDCon3 Combination Max Y 3.9E-05 16 13.56 5 15.79
Lower Platform Set B -UDCon3 Combination Min X 3.5E-05 83 13.56 40.4 15.79
Step X Y Z
Story Output Case Case Type Direction Drift Label
Type m m m
Lower Platform Set B -UDCon3 Combination Min Y 3.9E-05 16 13.56 5 15.79
Lower Platform Set B -UDCon4 Combination Max X 3.2E-05 83 13.56 40.4 15.79
Lower Platform Set B -UDCon4 Combination Max Y 3.6E-05 16 13.56 5 15.79
Lower Platform Set B -UDCon4 Combination Min X 3.2E-05 83 13.56 40.4 15.79
Lower Platform Set B -UDCon4 Combination Min Y 3.6E-05 16 13.56 5 15.79
Lower Platform Set B -UDCon5 Combination Max X 2.3E-05 83 13.56 40.4 15.79
Lower Platform Set B -UDCon5 Combination Max Y 2.8E-05 16 13.56 5 15.79
Lower Platform Set B -UDCon5 Combination Min X 2.3E-05 83 13.56 40.4 15.79
Lower Platform Set B -UDCon5 Combination Min Y 2.8E-05 16 13.56 5 15.79
Lower Platform Set B -UDCon6 Combination Max X 1.7E-05 83 13.56 40.4 15.79
Lower Platform Set B -UDCon6 Combination Max Y 2.1E-05 16 13.56 5 15.79
Lower Platform Set B -UDCon6 Combination Min X 1.7E-05 83 13.56 40.4 15.79
Lower Platform Set B -UDCon6 Combination Min Y 2.1E-05 16 13.56 5 15.79
Lower Platform Set B -UDCon7-1 Combination X 3.8E-05 83 13.56 40.4 15.79
Lower Platform Set B -UDCon7-1 Combination Y 3.9E-05 16 13.56 5 15.79
Lower Platform Set B -UDCon7-2 Combination X 3.4E-05 83 13.56 40.4 15.79
Lower Platform Set B -UDCon7-2 Combination Y 3E-05 16 13.56 5 15.79
Lower Platform Set B -UDCon7-3 Combination X 3.3E-05 83 13.56 40.4 15.79
Lower Platform Set B -UDCon7-3 Combination Y 3.9E-05 16 13.56 5 15.79
Lower Platform Set B -UDCon7-4 Combination X 3.6E-05 83 13.56 40.4 15.79
Lower Platform Set B -UDCon7-4 Combination Y 4.8E-05 16 13.56 5 15.79
Lower Platform Set B -UDCon8-1 Combination X 3.4E-05 83 13.56 40.4 15.79
Lower Platform Set B -UDCon8-1 Combination Y 3.6E-05 16 13.56 5 15.79
Lower Platform Set B -UDCon8-2 Combination X 3.1E-05 83 13.56 40.4 15.79
Lower Platform Set B -UDCon8-2 Combination Y 2.7E-05 16 13.56 5 15.79
Lower Platform Set B -UDCon8-3 Combination X 2.9E-05 83 13.56 40.4 15.79
Lower Platform Set B -UDCon8-3 Combination Y 3.6E-05 16 13.56 5 15.79
Lower Platform Set B -UDCon8-4 Combination X 3.3E-05 83 13.56 40.4 15.79
Lower Platform Set B -UDCon8-4 Combination Y 4.5E-05 16 13.56 5 15.79
Lower Platform Set B -UDCon9-1 Combination X 2.6E-05 83 13.56 40.4 15.79
Lower Platform Set B -UDCon9-1 Combination Y 2.9E-05 16 13.56 5 15.79
Lower Platform Set B -UDCon9-2 Combination X 2.2E-05 83 13.56 40.4 15.79
Lower Platform Set B -UDCon9-2 Combination Y 1.9E-05 16 13.56 5 15.79
Lower Platform Set B -UDCon9-3 Combination X 2.1E-05 83 13.56 40.4 15.79
Lower Platform Set B -UDCon9-3 Combination Y 2.8E-05 16 13.56 5 15.79
Lower Platform Set B -UDCon9-4 Combination X 2.4E-05 83 13.56 40.4 15.79
Lower Platform Set B -UDCon9-4 Combination Y 3.7E-05 16 13.56 5 15.79
Lower Platform Set B -UDCon10-1 Combination X 2E-05 83 13.56 40.4 15.79
Lower Platform Set B -UDCon10-1 Combination Y 2.1E-05 16 13.56 5 15.79
Lower Platform Set B -UDCon10-2 Combination X 1.6E-05 83 13.56 40.4 15.79
Lower Platform Set B -UDCon10-2 Combination Y 1.2E-05 16 13.56 5 15.79
Lower Platform Set B -UDCon10-3 Combination X 1.5E-05 83 13.56 40.4 15.79
Lower Platform Set B -UDCon10-3 Combination Y 2.1E-05 16 13.56 5 15.79
Lower Platform Set B -UDCon10-4 Combination X 1.8E-05 83 13.56 40.4 15.79
Lower Platform Set B -UDCon10-4 Combination Y 3E-05 16 13.56 5 15.79
Step X Y Z
Story Output Case Case Type Direction Drift Label
Type m m m
Lower Platform Set B-ENVE Combination Max X 1.5E-05 83 13.56 40.4 15.79
Lower Platform Set B-ENVE Combination Max Y 4.8E-05 16 13.56 5 15.79
Lower Platform Set B-ENVE Combination Min X 3.8E-05 83 13.56 40.4 15.79
Lower Platform Set B-ENVE Combination Min Y 1.2E-05 16 13.56 5 15.79
Lower Platform Set C -UDCon1 Combination X 1.7E-05 83 13.56 40.4 15.79
Lower Platform Set C -UDCon1 Combination Y 2.1E-05 16 13.56 5 15.79
Lower Platform Set C -UDCon2 Combination X 2.8E-05 83 13.56 40.4 15.79
Lower Platform Set C -UDCon2 Combination Y 3E-05 16 13.56 5 15.79
Lower Platform Set C -UDCon3 Combination Max X 2.8E-05 83 13.56 40.4 15.79
Lower Platform Set C -UDCon3 Combination Max Y 3E-05 16 13.56 5 15.79
Lower Platform Set C -UDCon3 Combination Min X 2.8E-05 83 13.56 40.4 15.79
Lower Platform Set C -UDCon3 Combination Min Y 3E-05 16 13.56 5 15.79
Lower Platform Set C -UDCon4 Combination Max X 2.4E-05 83 13.56 40.4 15.79
Lower Platform Set C -UDCon4 Combination Max Y 2.7E-05 16 13.56 5 15.79
Lower Platform Set C -UDCon4 Combination Min X 2.4E-05 83 13.56 40.4 15.79
Lower Platform Set C -UDCon4 Combination Min Y 2.7E-05 16 13.56 5 15.79
Lower Platform Set C -UDCon5 Combination Max X 1.7E-05 83 13.56 40.4 15.79
Lower Platform Set C -UDCon5 Combination Max Y 2.1E-05 16 13.56 5 15.79
Lower Platform Set C -UDCon5 Combination Min X 1.7E-05 83 13.56 40.4 15.79
Lower Platform Set C -UDCon5 Combination Min Y 2.1E-05 16 13.56 5 15.79
Lower Platform Set C -UDCon6-1 Combination X 3E-05 83 13.56 40.4 15.79
Lower Platform Set C -UDCon6-1 Combination Y 3.1E-05 16 13.56 5 15.79
Lower Platform Set C -UDCon6-2 Combination X 2.7E-05 83 13.56 40.4 15.79
Lower Platform Set C -UDCon6-2 Combination Y 2.1E-05 16 13.56 5 15.79
Lower Platform Set C -UDCon6-3 Combination X 2.5E-05 83 13.56 40.4 15.79
Lower Platform Set C -UDCon6-3 Combination Y 3E-05 16 13.56 5 15.79
Lower Platform Set C -UDCon6-4 Combination X 2.9E-05 83 13.56 40.4 15.79
Lower Platform Set C -UDCon6-4 Combination Y 3.9E-05 16 13.56 5 15.79
Lower Platform Set C -UDCon7-1 Combination X 2.7E-05 83 13.56 40.4 15.79
Lower Platform Set C -UDCon7-1 Combination Y 2.8E-05 16 13.56 5 15.79
Lower Platform Set C -UDCon7-2 Combination X 2.3E-05 83 13.56 40.4 15.79
Lower Platform Set C -UDCon7-2 Combination Y 1.8E-05 16 13.56 5 15.79
Lower Platform Set C -UDCon7-3 Combination X 2.2E-05 83 13.56 40.4 15.79
Lower Platform Set C -UDCon7-3 Combination Y 2.7E-05 16 13.56 5 15.79
Lower Platform Set C -UDCon7-4 Combination X 2.6E-05 83 13.56 40.4 15.79
Lower Platform Set C -UDCon7-4 Combination Y 3.7E-05 16 13.56 5 15.79
Lower Platform Set C -UDCon8-1 Combination X 2E-05 83 13.56 40.4 15.79
Lower Platform Set C -UDCon8-1 Combination Y 2.1E-05 16 13.56 5 15.79
Lower Platform Set C -UDCon8-2 Combination X 1.6E-05 83 13.56 40.4 15.79
Lower Platform Set C -UDCon8-2 Combination Y 1.2E-05 16 13.56 5 15.79
Lower Platform Set C -UDCon8-3 Combination X 1.5E-05 83 13.56 40.4 15.79
Lower Platform Set C -UDCon8-3 Combination Y 2.1E-05 16 13.56 5 15.79
Lower Platform Set C -UDCon8-4 Combination X 1.8E-05 83 13.56 40.4 15.79
Lower Platform Set C -UDCon8-4 Combination Y 3E-05 16 13.56 5 15.79
Lower Platform Set C- ENVE Combination Max X 1.5E-05 83 13.56 40.4 15.79
Step X Y Z
Story Output Case Case Type Direction Drift Label
Type m m m
Lower Platform Set C- ENVE Combination Max Y 3.9E-05 16 13.56 5 15.79
Lower Platform Set C- ENVE Combination Min X 3E-05 83 13.56 40.4 15.79
Lower Platform Set C- ENVE Combination Min Y 1.2E-05 16 13.56 5 15.79
Staircase landing level 2 DL LinStatic X 1E-05 42 13.56 19.85 13.48
Staircase landing level 2 DL LinStatic Y 1.4E-05 16 13.56 5 13.48
Staircase landing level 2 SDL LinStatic X 7E-06 74 5 35.22 13.48
Staircase landing level 2 SDL LinStatic Y 5E-06 16 13.56 5 13.48
Staircase landing level 2 LL LinStatic X 7E-06 74 5 35.22 13.48
Staircase landing level 2 LL LinStatic Y 7E-06 16 13.56 5 13.48
Staircase landing level 2 Acci Fx LinStatic X 3.476E-07 76 13.56 35.22 13.48
Staircase landing level 2 Acci Fx LinStatic Y 1E-06 42 13.56 19.85 13.48
Staircase landing level 2 Acci Fy LinStatic Y 2E-06 24 5 10.18 13.48
Staircase landing level 2 NL-0deg LinStatic X 4E-06 15 5 5 13.48
Staircase landing level 2 NL-0deg LinStatic Y 1E-06 81 5 40.4 13.48
Staircase landing level 2 NL-90deg LinStatic Y 1.1E-05 24 5 10.18 13.48
Staircase landing level 2 NL-180deg LinStatic X 4E-06 15 5 5 13.48
Staircase landing level 2 NL-180deg LinStatic Y 1E-06 81 5 40.4 13.48
Staircase landing level 2 NL-270deg LinStatic Y 1.1E-05 24 5 10.18 13.48
Staircase landing level 2 Set B -UDCon1 Combination X 1.9E-05 81 5 40.4 13.48
Staircase landing level 2 Set B -UDCon1 Combination Y 2.7E-05 16 13.56 5 13.48
Staircase landing level 2 SLS 1 Combination X 2.1E-05 74 5 35.22 13.48
Staircase landing level 2 SLS 1 Combination Y 2.6E-05 16 13.56 5 13.48
Staircase landing level 2 ALL DL Combination X 1.4E-05 81 5 40.4 13.48
Staircase landing level 2 ALL DL Combination Y 2E-05 16 13.56 5 13.48
Staircase landing level 2 ALL LL Combination X 7E-06 74 5 35.22 13.48
Staircase landing level 2 ALL LL Combination Y 7E-06 16 13.56 5 13.48
Staircase landing level 2 ULS-A1 Combination X 1.7E-05 81 5 40.4 13.48
Staircase landing level 2 ULS-A1 Combination Y 2.3E-05 16 13.56 5 13.48
Staircase landing level 2 ULS-A2 Combination X 1.6E-05 81 5 40.4 13.48
Staircase landing level 2 ULS-A2 Combination Y 2.1E-05 16 13.56 5 13.48
Staircase landing level 2 DCmpD1 Combination X 1.4E-05 81 5 40.4 13.48
Staircase landing level 2 DCmpD1 Combination Y 2E-05 16 13.56 5 13.48
Staircase landing level 2 DCmpD2 Combination X 2.1E-05 74 5 35.22 13.48
Staircase landing level 2 DCmpD2 Combination Y 2.6E-05 16 13.56 5 13.48
Staircase landing level 2 DCmpS1 Combination X 1.9E-05 81 5 40.4 13.48
Staircase landing level 2 DCmpS1 Combination Y 2.7E-05 16 13.56 5 13.48
Staircase landing level 2 DCmpS2 Combination X 2.9E-05 74 5 35.22 13.48
Staircase landing level 2 DCmpS2 Combination Y 3.6E-05 16 13.56 5 13.48
Staircase landing level 2 DCmpC1 Combination X 1.6E-05 42 13.56 19.85 13.48
Staircase landing level 2 DCmpC1 Combination Y 2.2E-05 16 13.56 5 13.48
Staircase landing level 2 Geo-Com1 Combination X 2.9E-05 74 5 35.22 13.48
Staircase landing level 2 Geo-Com1 Combination Y 3.6E-05 16 13.56 5 13.48
Staircase landing level 2 Geo-Com2 Combination X 2.3E-05 74 5 35.22 13.48
Staircase landing level 2 Geo-Com2 Combination Y 2.8E-05 16 13.56 5 13.48
Staircase landing level 2 SLS 2 Combination Max X 2.1E-05 74 5 35.22 13.48
Step X Y Z
Story Output Case Case Type Direction Drift Label
Type m m m
Staircase landing level 2 SLS 2 Combination Max Y 2.6E-05 16 13.56 5 13.48
Staircase landing level 2 SLS 2 Combination Min X 2.1E-05 74 5 35.22 13.48
Staircase landing level 2 SLS 2 Combination Min Y 2.6E-05 16 13.56 5 13.48
Staircase landing level 2 SLS 3 Combination Max X 1.9E-05 81 5 40.4 13.48
Staircase landing level 2 SLS 3 Combination Max Y 2.4E-05 16 13.56 5 13.48
Staircase landing level 2 SLS 3 Combination Min X 1.9E-05 81 5 40.4 13.48
Staircase landing level 2 SLS 3 Combination Min Y 2.4E-05 16 13.56 5 13.48
Staircase landing level 2 SLS 4 Combination Max X 1.4E-05 81 5 40.4 13.48
Staircase landing level 2 SLS 4 Combination Max Y 2E-05 16 13.56 5 13.48
Staircase landing level 2 SLS 4 Combination Min X 1.4E-05 81 5 40.4 13.48
Staircase landing level 2 SLS 4 Combination Min Y 2E-05 16 13.56 5 13.48
Staircase landing level 2 SLS ENVE Combination Max X 1.4E-05 81 5 40.4 13.48
Staircase landing level 2 SLS ENVE Combination Max Y 2.6E-05 16 13.56 5 13.48
Staircase landing level 2 SLS ENVE Combination Min X 2.1E-05 74 5 35.22 13.48
Staircase landing level 2 SLS ENVE Combination Min Y 2E-05 16 13.56 5 13.48
Staircase landing level 2 Set B -UDCon2 Combination X 2.9E-05 74 5 35.22 13.48
Staircase landing level 2 Set B -UDCon2 Combination Y 3.6E-05 16 13.56 5 13.48
Staircase landing level 2 Set B -UDCon3 Combination Max X 2.9E-05 74 5 35.22 13.48
Staircase landing level 2 Set B -UDCon3 Combination Max Y 3.6E-05 16 13.56 5 13.48
Staircase landing level 2 Set B -UDCon3 Combination Min X 2.9E-05 74 5 35.22 13.48
Staircase landing level 2 Set B -UDCon3 Combination Min Y 3.6E-05 16 13.56 5 13.48
Staircase landing level 2 Set B -UDCon4 Combination Max X 2.6E-05 81 5 40.4 13.48
Staircase landing level 2 Set B -UDCon4 Combination Max Y 3.4E-05 16 13.56 5 13.48
Staircase landing level 2 Set B -UDCon4 Combination Min X 2.6E-05 81 5 40.4 13.48
Staircase landing level 2 Set B -UDCon4 Combination Min Y 3.4E-05 16 13.56 5 13.48
Staircase landing level 2 Set B -UDCon5 Combination Max X 1.9E-05 81 5 40.4 13.48
Staircase landing level 2 Set B -UDCon5 Combination Max Y 2.7E-05 16 13.56 5 13.48
Staircase landing level 2 Set B -UDCon5 Combination Min X 1.9E-05 81 5 40.4 13.48
Staircase landing level 2 Set B -UDCon5 Combination Min Y 2.7E-05 16 13.56 5 13.48
Staircase landing level 2 Set B -UDCon6 Combination Max X 1.4E-05 81 5 40.4 13.48
Staircase landing level 2 Set B -UDCon6 Combination Max Y 2E-05 16 13.56 5 13.48
Staircase landing level 2 Set B -UDCon6 Combination Min X 1.4E-05 81 5 40.4 13.48
Staircase landing level 2 Set B -UDCon6 Combination Min Y 2E-05 16 13.56 5 13.48
Staircase landing level 2 Set B -UDCon7-1 Combination X 3.1E-05 81 5 40.4 13.48
Staircase landing level 2 Set B -UDCon7-1 Combination Y 3.7E-05 16 13.56 5 13.48
Staircase landing level 2 Set B -UDCon7-2 Combination X 2.8E-05 81 5 40.4 13.48
Staircase landing level 2 Set B -UDCon7-2 Combination Y 2.8E-05 16 13.56 5 13.48
Staircase landing level 2 Set B -UDCon7-3 Combination X 2.7E-05 74 5 35.22 13.48
Staircase landing level 2 Set B -UDCon7-3 Combination Y 3.6E-05 16 13.56 5 13.48
Staircase landing level 2 Set B -UDCon7-4 Combination X 3.1E-05 74 5 35.22 13.48
Staircase landing level 2 Set B -UDCon7-4 Combination Y 4.5E-05 16 13.56 5 13.48
Staircase landing level 2 Set B -UDCon8-1 Combination X 2.8E-05 81 5 40.4 13.48
Staircase landing level 2 Set B -UDCon8-1 Combination Y 3.4E-05 16 13.56 5 13.48
Staircase landing level 2 Set B -UDCon8-2 Combination X 2.5E-05 81 5 40.4 13.48
Staircase landing level 2 Set B -UDCon8-2 Combination Y 2.5E-05 16 13.56 5 13.48
Step X Y Z
Story Output Case Case Type Direction Drift Label
Type m m m
Staircase landing level 2 Set B -UDCon8-3 Combination X 2.4E-05 74 5 35.22 13.48
Staircase landing level 2 Set B -UDCon8-3 Combination Y 3.3E-05 16 13.56 5 13.48
Staircase landing level 2 Set B -UDCon8-4 Combination X 2.8E-05 74 5 35.22 13.48
Staircase landing level 2 Set B -UDCon8-4 Combination Y 4.2E-05 16 13.56 5 13.48
Staircase landing level 2 Set B -UDCon9-1 Combination X 2.1E-05 81 5 40.4 13.48
Staircase landing level 2 Set B -UDCon9-1 Combination Y 2.7E-05 16 13.56 5 13.48
Staircase landing level 2 Set B -UDCon9-2 Combination X 1.8E-05 81 5 40.4 13.48
Staircase landing level 2 Set B -UDCon9-2 Combination Y 1.8E-05 16 13.56 5 13.48
Staircase landing level 2 Set B -UDCon9-3 Combination X 1.7E-05 74 5 35.22 13.48
Staircase landing level 2 Set B -UDCon9-3 Combination Y 2.6E-05 16 13.56 5 13.48
Staircase landing level 2 Set B -UDCon9-4 Combination X 2E-05 74 5 35.22 13.48
Staircase landing level 2 Set B -UDCon9-4 Combination Y 3.5E-05 16 13.56 5 13.48
Staircase landing level 2 Set B -UDCon10-1 Combination X 1.6E-05 81 5 40.4 13.48
Staircase landing level 2 Set B -UDCon10-1 Combination Y 2E-05 16 13.56 5 13.48
Staircase landing level 2 Set B -UDCon10-2 Combination X 1.3E-05 50 5 25.03 13.48
Staircase landing level 2 Set B -UDCon10-2 Combination Y 1.1E-05 16 13.56 5 13.48
Staircase landing level 2 Set B -UDCon10-3 Combination X 1.2E-05 74 5 35.22 13.48
Staircase landing level 2 Set B -UDCon10-3 Combination Y 2E-05 16 13.56 5 13.48
Staircase landing level 2 Set B -UDCon10-4 Combination X 1.6E-05 74 5 35.22 13.48
Staircase landing level 2 Set B -UDCon10-4 Combination Y 2.8E-05 16 13.56 5 13.48
Staircase landing level 2 Set B-ENVE Combination Max X 1.2E-05 74 5 35.22 13.48
Staircase landing level 2 Set B-ENVE Combination Max Y 4.5E-05 16 13.56 5 13.48
Staircase landing level 2 Set B-ENVE Combination Min X 3.1E-05 81 5 40.4 13.48
Staircase landing level 2 Set B-ENVE Combination Min Y 1.1E-05 16 13.56 5 13.48
Staircase landing level 2 Set C -UDCon1 Combination X 1.4E-05 81 5 40.4 13.48
Staircase landing level 2 Set C -UDCon1 Combination Y 2E-05 16 13.56 5 13.48
Staircase landing level 2 Set C -UDCon2 Combination X 2.3E-05 74 5 35.22 13.48
Staircase landing level 2 Set C -UDCon2 Combination Y 2.8E-05 16 13.56 5 13.48
Staircase landing level 2 Set C -UDCon3 Combination Max X 2.3E-05 74 5 35.22 13.48
Staircase landing level 2 Set C -UDCon3 Combination Max Y 2.8E-05 16 13.56 5 13.48
Staircase landing level 2 Set C -UDCon3 Combination Min X 2.3E-05 74 5 35.22 13.48
Staircase landing level 2 Set C -UDCon3 Combination Min Y 2.8E-05 16 13.56 5 13.48
Staircase landing level 2 Set C -UDCon4 Combination Max X 2E-05 74 5 35.22 13.48
Staircase landing level 2 Set C -UDCon4 Combination Max Y 2.6E-05 16 13.56 5 13.48
Staircase landing level 2 Set C -UDCon4 Combination Min X 2E-05 74 5 35.22 13.48
Staircase landing level 2 Set C -UDCon4 Combination Min Y 2.6E-05 16 13.56 5 13.48
Staircase landing level 2 Set C -UDCon5 Combination Max X 1.4E-05 81 5 40.4 13.48
Staircase landing level 2 Set C -UDCon5 Combination Max Y 2E-05 16 13.56 5 13.48
Staircase landing level 2 Set C -UDCon5 Combination Min X 1.4E-05 81 5 40.4 13.48
Staircase landing level 2 Set C -UDCon5 Combination Min Y 2E-05 16 13.56 5 13.48
Staircase landing level 2 Set C -UDCon6-1 Combination X 2.5E-05 81 5 40.4 13.48
Staircase landing level 2 Set C -UDCon6-1 Combination Y 2.8E-05 16 13.56 5 13.48
Staircase landing level 2 Set C -UDCon6-2 Combination X 2.2E-05 81 5 40.4 13.48
Staircase landing level 2 Set C -UDCon6-2 Combination Y 2E-05 16 13.56 5 13.48
Staircase landing level 2 Set C -UDCon6-3 Combination X 2.1E-05 74 5 35.22 13.48
Step X Y Z
Story Output Case Case Type Direction Drift Label
Type m m m
Staircase landing level 2 Set C -UDCon6-3 Combination Y 2.8E-05 16 13.56 5 13.48
Staircase landing level 2 Set C -UDCon6-4 Combination X 2.5E-05 74 5 35.22 13.48
Staircase landing level 2 Set C -UDCon6-4 Combination Y 3.7E-05 16 13.56 5 13.48
Staircase landing level 2 Set C -UDCon7-1 Combination X 2.2E-05 81 5 40.4 13.48
Staircase landing level 2 Set C -UDCon7-1 Combination Y 2.6E-05 16 13.56 5 13.48
Staircase landing level 2 Set C -UDCon7-2 Combination X 1.9E-05 81 5 40.4 13.48
Staircase landing level 2 Set C -UDCon7-2 Combination Y 1.7E-05 16 13.56 5 13.48
Staircase landing level 2 Set C -UDCon7-3 Combination X 1.8E-05 74 5 35.22 13.48
Staircase landing level 2 Set C -UDCon7-3 Combination Y 2.6E-05 16 13.56 5 13.48
Staircase landing level 2 Set C -UDCon7-4 Combination X 2.2E-05 74 5 35.22 13.48
Staircase landing level 2 Set C -UDCon7-4 Combination Y 3.4E-05 16 13.56 5 13.48
Staircase landing level 2 Set C -UDCon8-1 Combination X 1.6E-05 81 5 40.4 13.48
Staircase landing level 2 Set C -UDCon8-1 Combination Y 2E-05 16 13.56 5 13.48
Staircase landing level 2 Set C -UDCon8-2 Combination X 1.3E-05 50 5 25.03 13.48
Staircase landing level 2 Set C -UDCon8-2 Combination Y 1.1E-05 16 13.56 5 13.48
Staircase landing level 2 Set C -UDCon8-3 Combination X 1.2E-05 74 5 35.22 13.48
Staircase landing level 2 Set C -UDCon8-3 Combination Y 2E-05 16 13.56 5 13.48
Staircase landing level 2 Set C -UDCon8-4 Combination X 1.6E-05 74 5 35.22 13.48
Staircase landing level 2 Set C -UDCon8-4 Combination Y 2.8E-05 16 13.56 5 13.48
Staircase landing level 2 Set C- ENVE Combination Max X 1.2E-05 74 5 35.22 13.48
Staircase landing level 2 Set C- ENVE Combination Max Y 3.7E-05 16 13.56 5 13.48
Staircase landing level 2 Set C- ENVE Combination Min X 2.5E-05 81 5 40.4 13.48
Staircase landing level 2 Set C- ENVE Combination Min Y 1.1E-05 16 13.56 5 13.48
Staircase landig level 1 DL LinStatic X 1.2E-05 41 5 19.85 11.17
Staircase landig level 1 DL LinStatic Y 1.6E-05 16 13.56 5 11.17
Staircase landig level 1 SDL LinStatic X 5E-06 76 13.56 35.22 11.17
Staircase landig level 1 SDL LinStatic Y 5E-06 51 13.56 25.03 11.17
Staircase landig level 1 LL LinStatic X 5E-06 24 5 10.18 11.17
Staircase landig level 1 LL LinStatic Y 7E-06 16 13.56 5 11.17
Staircase landig level 1 Acci Fx LinStatic X 4.846E-07 76 13.56 35.22 11.17
Staircase landig level 1 Acci Fx LinStatic Y 1E-06 51 13.56 25.03 11.17
Staircase landig level 1 Acci Fy LinStatic Y 2E-06 51 13.56 25.03 11.17
Staircase landig level 1 NL-0deg LinStatic X 4E-06 16 13.56 5 11.17
Staircase landig level 1 NL-0deg LinStatic Y 1E-06 81 5 40.4 11.17
Staircase landig level 1 NL-90deg LinStatic Y 1E-05 15 5 5 11.17
Staircase landig level 1 NL-180deg LinStatic X 4E-06 16 13.56 5 11.17
Staircase landig level 1 NL-180deg LinStatic Y 1E-06 81 5 40.4 11.17
Staircase landig level 1 NL-270deg LinStatic Y 1E-05 15 5 5 11.17
Staircase landig level 1 Set B -UDCon1 Combination X 2.1E-05 81 5 40.4 11.17
Staircase landig level 1 Set B -UDCon1 Combination Y 2.9E-05 16 13.56 5 11.17
Staircase landig level 1 SLS 1 Combination X 2E-05 81 5 40.4 11.17
Staircase landig level 1 SLS 1 Combination Y 2.8E-05 16 13.56 5 11.17
Staircase landig level 1 ALL DL Combination X 1.5E-05 81 5 40.4 11.17
Staircase landig level 1 ALL DL Combination Y 2.1E-05 16 13.56 5 11.17
Staircase landig level 1 ALL LL Combination X 5E-06 24 5 10.18 11.17
Step X Y Z
Story Output Case Case Type Direction Drift Label
Type m m m
Staircase landig level 1 ALL LL Combination Y 7E-06 16 13.56 5 11.17
Staircase landig level 1 ULS-A1 Combination X 1.7E-05 81 5 40.4 11.17
Staircase landig level 1 ULS-A1 Combination Y 2.4E-05 16 13.56 5 11.17
Staircase landig level 1 ULS-A2 Combination X 1.7E-05 24 5 10.18 11.17
Staircase landig level 1 ULS-A2 Combination Y 2.2E-05 16 13.56 5 11.17
Staircase landig level 1 DCmpD1 Combination X 1.5E-05 81 5 40.4 11.17
Staircase landig level 1 DCmpD1 Combination Y 2.1E-05 16 13.56 5 11.17
Staircase landig level 1 DCmpD2 Combination X 2E-05 81 5 40.4 11.17
Staircase landig level 1 DCmpD2 Combination Y 2.8E-05 16 13.56 5 11.17
Staircase landig level 1 DCmpS1 Combination X 2.1E-05 81 5 40.4 11.17
Staircase landig level 1 DCmpS1 Combination Y 2.9E-05 16 13.56 5 11.17
Staircase landig level 1 DCmpS2 Combination X 2.7E-05 81 5 40.4 11.17
Staircase landig level 1 DCmpS2 Combination Y 3.9E-05 16 13.56 5 11.17
Staircase landig level 1 DCmpC1 Combination X 1.8E-05 41 5 19.85 11.17
Staircase landig level 1 DCmpC1 Combination Y 2.4E-05 16 13.56 5 11.17
Staircase landig level 1 Geo-Com1 Combination X 2.7E-05 81 5 40.4 11.17
Staircase landig level 1 Geo-Com1 Combination Y 3.9E-05 16 13.56 5 11.17
Staircase landig level 1 Geo-Com2 Combination X 2.1E-05 81 5 40.4 11.17
Staircase landig level 1 Geo-Com2 Combination Y 3E-05 16 13.56 5 11.17
Staircase landig level 1 SLS 2 Combination Max X 2E-05 81 5 40.4 11.17
Staircase landig level 1 SLS 2 Combination Max Y 2.8E-05 16 13.56 5 11.17
Staircase landig level 1 SLS 2 Combination Min X 2E-05 81 5 40.4 11.17
Staircase landig level 1 SLS 2 Combination Min Y 2.8E-05 16 13.56 5 11.17
Staircase landig level 1 SLS 3 Combination Max X 1.8E-05 81 5 40.4 11.17
Staircase landig level 1 SLS 3 Combination Max Y 2.6E-05 16 13.56 5 11.17
Staircase landig level 1 SLS 3 Combination Min X 1.8E-05 81 5 40.4 11.17
Staircase landig level 1 SLS 3 Combination Min Y 2.6E-05 16 13.56 5 11.17
Staircase landig level 1 SLS 4 Combination Max X 1.5E-05 81 5 40.4 11.17
Staircase landig level 1 SLS 4 Combination Max Y 2.1E-05 16 13.56 5 11.17
Staircase landig level 1 SLS 4 Combination Min X 1.5E-05 81 5 40.4 11.17
Staircase landig level 1 SLS 4 Combination Min Y 2.1E-05 16 13.56 5 11.17
Staircase landig level 1 SLS ENVE Combination Max X 1.5E-05 81 5 40.4 11.17
Staircase landig level 1 SLS ENVE Combination Max Y 2.8E-05 16 13.56 5 11.17
Staircase landig level 1 SLS ENVE Combination Min X 2E-05 81 5 40.4 11.17
Staircase landig level 1 SLS ENVE Combination Min Y 2.1E-05 16 13.56 5 11.17
Staircase landig level 1 Set B -UDCon2 Combination X 2.7E-05 81 5 40.4 11.17
Staircase landig level 1 Set B -UDCon2 Combination Y 3.9E-05 16 13.56 5 11.17
Staircase landig level 1 Set B -UDCon3 Combination Max X 2.7E-05 81 5 40.4 11.17
Staircase landig level 1 Set B -UDCon3 Combination Max Y 3.9E-05 16 13.56 5 11.17
Staircase landig level 1 Set B -UDCon3 Combination Min X 2.7E-05 81 5 40.4 11.17
Staircase landig level 1 Set B -UDCon3 Combination Min Y 3.9E-05 16 13.56 5 11.17
Staircase landig level 1 Set B -UDCon4 Combination Max X 2.5E-05 81 5 40.4 11.17
Staircase landig level 1 Set B -UDCon4 Combination Max Y 3.6E-05 16 13.56 5 11.17
Staircase landig level 1 Set B -UDCon4 Combination Min X 2.5E-05 81 5 40.4 11.17
Staircase landig level 1 Set B -UDCon4 Combination Min Y 3.6E-05 16 13.56 5 11.17
Step X Y Z
Story Output Case Case Type Direction Drift Label
Type m m m
Staircase landig level 1 Set B -UDCon5 Combination Max X 2.1E-05 81 5 40.4 11.17
Staircase landig level 1 Set B -UDCon5 Combination Max Y 2.9E-05 16 13.56 5 11.17
Staircase landig level 1 Set B -UDCon5 Combination Min X 2.1E-05 81 5 40.4 11.17
Staircase landig level 1 Set B -UDCon5 Combination Min Y 2.9E-05 16 13.56 5 11.17
Staircase landig level 1 Set B -UDCon6 Combination Max X 1.5E-05 81 5 40.4 11.17
Staircase landig level 1 Set B -UDCon6 Combination Max Y 2.1E-05 16 13.56 5 11.17
Staircase landig level 1 Set B -UDCon6 Combination Min X 1.5E-05 81 5 40.4 11.17
Staircase landig level 1 Set B -UDCon6 Combination Min Y 2.1E-05 16 13.56 5 11.17
Staircase landig level 1 Set B -UDCon7-1 Combination X 3.1E-05 24 5 10.18 11.17
Staircase landig level 1 Set B -UDCon7-1 Combination Y 3.9E-05 16 13.56 5 11.17
Staircase landig level 1 Set B -UDCon7-2 Combination X 2.9E-05 24 5 10.18 11.17
Staircase landig level 1 Set B -UDCon7-2 Combination Y 3.1E-05 16 13.56 5 11.17
Staircase landig level 1 Set B -UDCon7-3 Combination X 2.5E-05 81 5 40.4 11.17
Staircase landig level 1 Set B -UDCon7-3 Combination Y 3.9E-05 16 13.56 5 11.17
Staircase landig level 1 Set B -UDCon7-4 Combination X 2.7E-05 81 5 40.4 11.17
Staircase landig level 1 Set B -UDCon7-4 Combination Y 4.7E-05 16 13.56 5 11.17
Staircase landig level 1 Set B -UDCon8-1 Combination X 2.9E-05 24 5 10.18 11.17
Staircase landig level 1 Set B -UDCon8-1 Combination Y 3.6E-05 16 13.56 5 11.17
Staircase landig level 1 Set B -UDCon8-2 Combination X 2.7E-05 24 5 10.18 11.17
Staircase landig level 1 Set B -UDCon8-2 Combination Y 2.8E-05 16 13.56 5 11.17
Staircase landig level 1 Set B -UDCon8-3 Combination X 2.3E-05 81 5 40.4 11.17
Staircase landig level 1 Set B -UDCon8-3 Combination Y 3.6E-05 16 13.56 5 11.17
Staircase landig level 1 Set B -UDCon8-4 Combination X 2.5E-05 81 5 40.4 11.17
Staircase landig level 1 Set B -UDCon8-4 Combination Y 4.4E-05 16 13.56 5 11.17
Staircase landig level 1 Set B -UDCon9-1 Combination X 2.3E-05 24 5 10.18 11.17
Staircase landig level 1 Set B -UDCon9-1 Combination Y 2.9E-05 16 13.56 5 11.17
Staircase landig level 1 Set B -UDCon9-2 Combination X 2.2E-05 24 5 10.18 11.17
Staircase landig level 1 Set B -UDCon9-2 Combination Y 2.1E-05 16 13.56 5 11.17
Staircase landig level 1 Set B -UDCon9-3 Combination X 1.8E-05 81 5 40.4 11.17
Staircase landig level 1 Set B -UDCon9-3 Combination Y 2.8E-05 16 13.56 5 11.17
Staircase landig level 1 Set B -UDCon9-4 Combination X 2.1E-05 81 5 40.4 11.17
Staircase landig level 1 Set B -UDCon9-4 Combination Y 3.7E-05 16 13.56 5 11.17
Staircase landig level 1 Set B -UDCon10-1 Combination X 1.8E-05 24 5 10.18 11.17
Staircase landig level 1 Set B -UDCon10-1 Combination Y 2.1E-05 16 13.56 5 11.17
Staircase landig level 1 Set B -UDCon10-2 Combination X 1.7E-05 24 5 10.18 11.17
Staircase landig level 1 Set B -UDCon10-2 Combination Y 1.3E-05 16 13.56 5 11.17
Staircase landig level 1 Set B -UDCon10-3 Combination X 1.3E-05 81 5 40.4 11.17
Staircase landig level 1 Set B -UDCon10-3 Combination Y 2.1E-05 16 13.56 5 11.17
Staircase landig level 1 Set B -UDCon10-4 Combination X 1.6E-05 81 5 40.4 11.17
Staircase landig level 1 Set B -UDCon10-4 Combination Y 2.9E-05 16 13.56 5 11.17
Staircase landig level 1 Set B-ENVE Combination Max X 1.3E-05 81 5 40.4 11.17
Staircase landig level 1 Set B-ENVE Combination Max Y 4.7E-05 16 13.56 5 11.17
Staircase landig level 1 Set B-ENVE Combination Min X 3.1E-05 24 5 10.18 11.17
Staircase landig level 1 Set B-ENVE Combination Min Y 1.3E-05 16 13.56 5 11.17
Staircase landig level 1 Set C -UDCon1 Combination X 1.5E-05 81 5 40.4 11.17
Step X Y Z
Story Output Case Case Type Direction Drift Label
Type m m m
Staircase landig level 1 Set C -UDCon1 Combination Y 2.1E-05 16 13.56 5 11.17
Staircase landig level 1 Set C -UDCon2 Combination X 2.1E-05 81 5 40.4 11.17
Staircase landig level 1 Set C -UDCon2 Combination Y 3E-05 16 13.56 5 11.17
Staircase landig level 1 Set C -UDCon3 Combination Max X 2.1E-05 81 5 40.4 11.17
Staircase landig level 1 Set C -UDCon3 Combination Max Y 3E-05 16 13.56 5 11.17
Staircase landig level 1 Set C -UDCon3 Combination Min X 2.1E-05 81 5 40.4 11.17
Staircase landig level 1 Set C -UDCon3 Combination Min Y 3E-05 16 13.56 5 11.17
Staircase landig level 1 Set C -UDCon4 Combination Max X 1.9E-05 81 5 40.4 11.17
Staircase landig level 1 Set C -UDCon4 Combination Max Y 2.7E-05 16 13.56 5 11.17
Staircase landig level 1 Set C -UDCon4 Combination Min X 1.9E-05 81 5 40.4 11.17
Staircase landig level 1 Set C -UDCon4 Combination Min Y 2.7E-05 16 13.56 5 11.17
Staircase landig level 1 Set C -UDCon5 Combination Max X 1.5E-05 81 5 40.4 11.17
Staircase landig level 1 Set C -UDCon5 Combination Max Y 2.1E-05 16 13.56 5 11.17
Staircase landig level 1 Set C -UDCon5 Combination Min X 1.5E-05 81 5 40.4 11.17
Staircase landig level 1 Set C -UDCon5 Combination Min Y 2.1E-05 16 13.56 5 11.17
Staircase landig level 1 Set C -UDCon6-1 Combination X 2.5E-05 24 5 10.18 11.17
Staircase landig level 1 Set C -UDCon6-1 Combination Y 3E-05 16 13.56 5 11.17
Staircase landig level 1 Set C -UDCon6-2 Combination X 2.3E-05 24 5 10.18 11.17
Staircase landig level 1 Set C -UDCon6-2 Combination Y 2.2E-05 16 13.56 5 11.17
Staircase landig level 1 Set C -UDCon6-3 Combination X 1.9E-05 81 5 40.4 11.17
Staircase landig level 1 Set C -UDCon6-3 Combination Y 3E-05 16 13.56 5 11.17
Staircase landig level 1 Set C -UDCon6-4 Combination X 2.1E-05 81 5 40.4 11.17
Staircase landig level 1 Set C -UDCon6-4 Combination Y 3.8E-05 16 13.56 5 11.17
Staircase landig level 1 Set C -UDCon7-1 Combination X 2.3E-05 24 5 10.18 11.17
Staircase landig level 1 Set C -UDCon7-1 Combination Y 2.8E-05 16 13.56 5 11.17
Staircase landig level 1 Set C -UDCon7-2 Combination X 2.1E-05 24 5 10.18 11.17
Staircase landig level 1 Set C -UDCon7-2 Combination Y 1.9E-05 16 13.56 5 11.17
Staircase landig level 1 Set C -UDCon7-3 Combination X 1.7E-05 81 5 40.4 11.17
Staircase landig level 1 Set C -UDCon7-3 Combination Y 2.7E-05 16 13.56 5 11.17
Staircase landig level 1 Set C -UDCon7-4 Combination X 2E-05 81 5 40.4 11.17
Staircase landig level 1 Set C -UDCon7-4 Combination Y 3.5E-05 16 13.56 5 11.17
Staircase landig level 1 Set C -UDCon8-1 Combination X 1.8E-05 24 5 10.18 11.17
Staircase landig level 1 Set C -UDCon8-1 Combination Y 2.1E-05 16 13.56 5 11.17
Staircase landig level 1 Set C -UDCon8-2 Combination X 1.7E-05 24 5 10.18 11.17
Staircase landig level 1 Set C -UDCon8-2 Combination Y 1.3E-05 16 13.56 5 11.17
Staircase landig level 1 Set C -UDCon8-3 Combination X 1.3E-05 81 5 40.4 11.17
Staircase landig level 1 Set C -UDCon8-3 Combination Y 2.1E-05 16 13.56 5 11.17
Staircase landig level 1 Set C -UDCon8-4 Combination X 1.6E-05 81 5 40.4 11.17
Staircase landig level 1 Set C -UDCon8-4 Combination Y 2.9E-05 16 13.56 5 11.17
Staircase landig level 1 Set C- ENVE Combination Max X 1.3E-05 81 5 40.4 11.17
Staircase landig level 1 Set C- ENVE Combination Max Y 3.8E-05 16 13.56 5 11.17
Staircase landig level 1 Set C- ENVE Combination Min X 2.5E-05 24 5 10.18 11.17
Staircase landig level 1 Set C- ENVE Combination Min Y 1.3E-05 16 13.56 5 11.17
Concourse DL LinStatic X 0.000101 146 13.56 48.58 8.86
Concourse DL LinStatic Y 1.7E-05 425 7.9 0 8.86
Step X Y Z
Story Output Case Case Type Direction Drift Label
Type m m m
Concourse SDL LinStatic X 0.000113 146 13.56 48.58 8.86
Concourse LL LinStatic X 5.7E-05 146 13.56 48.58 8.86
Concourse Acci Fx LinStatic X 6E-06 99 21.31 26.725 8.86
Concourse Acci Fy LinStatic X 6E-06 277 -6.2 0 8.86
Concourse Acci Fy LinStatic Y 1.7E-05 99 21.31 26.725 8.86
Concourse NL-0deg LinStatic X 0.000226 277 -6.2 0 8.86
Concourse NL-90deg LinStatic X 1.8E-05 277 -6.2 0 8.86
Concourse NL-90deg LinStatic Y 6.5E-05 420 3.15 0 8.86
Concourse NL-180deg LinStatic X 0.000226 277 -6.2 0 8.86
Concourse NL-270deg LinStatic X 1.8E-05 277 -6.2 0 8.86
Concourse NL-270deg LinStatic Y 6.5E-05 420 3.15 0 8.86
Concourse Set B -UDCon1 Combination X 0.000288 146 13.56 48.58 8.86
Concourse SLS 1 Combination X 0.000271 146 13.56 48.58 8.86
Concourse ALL DL Combination X 0.000214 146 13.56 48.58 8.86
Concourse ALL LL Combination X 5.7E-05 146 13.56 48.58 8.86
Concourse ULS-A1 Combination X 0.000237 146 13.56 48.58 8.86
Concourse ULS-A2 Combination X 0.000234 146 13.56 48.58 8.86
Concourse DCmpD1 Combination X 0.000214 146 13.56 48.58 8.86
Concourse DCmpD2 Combination X 0.000271 146 13.56 48.58 8.86
Concourse DCmpS1 Combination X 0.000288 146 13.56 48.58 8.86
Concourse DCmpS2 Combination X 0.000374 146 13.56 48.58 8.86
Concourse DCmpC1 Combination X 0.000151 146 13.56 48.58 8.86
Concourse DCmpC1 Combination Y 2.5E-05 425 7.9 0 8.86
Concourse Geo-Com1 Combination X 0.000374 146 13.56 48.58 8.86
Concourse Geo-Com2 Combination X 0.000288 146 13.56 48.58 8.86
Concourse SLS 2 Combination Max X 0.000271 146 13.56 48.58 8.86
Concourse SLS 2 Combination Min X 0.000271 146 13.56 48.58 8.86
Concourse SLS 3 Combination Max X 0.000254 146 13.56 48.58 8.86
Concourse SLS 3 Combination Min X 0.000254 146 13.56 48.58 8.86
Concourse SLS 4 Combination Max X 0.000214 146 13.56 48.58 8.86
Concourse SLS 4 Combination Min X 0.000214 146 13.56 48.58 8.86
Concourse SLS ENVE Combination Max X 0.000214 146 13.56 48.58 8.86
Concourse SLS ENVE Combination Min X 0.000271 146 13.56 48.58 8.86
Concourse Set B -UDCon2 Combination X 0.000374 146 13.56 48.58 8.86
Concourse Set B -UDCon3 Combination Max X 0.000374 146 13.56 48.58 8.86
Concourse Set B -UDCon3 Combination Min X 0.000374 146 13.56 48.58 8.86
Concourse Set B -UDCon4 Combination Max X 0.000348 146 13.56 48.58 8.86
Concourse Set B -UDCon4 Combination Min X 0.000348 146 13.56 48.58 8.86
Concourse Set B -UDCon5 Combination Max X 0.000288 146 13.56 48.58 8.86
Concourse Set B -UDCon5 Combination Min X 0.000288 146 13.56 48.58 8.86
Concourse Set B -UDCon6 Combination Max X 0.000214 146 13.56 48.58 8.86
Concourse Set B -UDCon6 Combination Min X 0.000214 146 13.56 48.58 8.86
Concourse Set B -UDCon7-1 Combination X 0.000364 146 13.56 48.58 8.86
Concourse Set B -UDCon7-2 Combination X 0.000368 146 13.56 48.58 8.86
Concourse Set B -UDCon7-2 Combination Y 5.4E-05 420 3.15 0 8.86
Step X Y Z
Story Output Case Case Type Direction Drift Label
Type m m m
Concourse Set B -UDCon7-3 Combination X 0.000428 277 -6.2 0 8.86
Concourse Set B -UDCon7-4 Combination X 0.000379 146 13.56 48.58 8.86
Concourse Set B -UDCon8-1 Combination X 0.000339 146 13.56 48.58 8.86
Concourse Set B -UDCon8-2 Combination X 0.000343 146 13.56 48.58 8.86
Concourse Set B -UDCon8-2 Combination Y 5.3E-05 420 3.15 0 8.86
Concourse Set B -UDCon8-3 Combination X 0.000412 277 -6.2 0 8.86
Concourse Set B -UDCon8-4 Combination X 0.000354 146 13.56 48.58 8.86
Concourse Set B -UDCon8-4 Combination Y 7.7E-05 420 3.15 0 8.86
Concourse Set B -UDCon9-1 Combination X 0.000279 146 13.56 48.58 8.86
Concourse Set B -UDCon9-2 Combination X 0.000283 146 13.56 48.58 8.86
Concourse Set B -UDCon9-2 Combination Y 5.3E-05 420 3.15 0 8.86
Concourse Set B -UDCon9-3 Combination X 0.000376 277 -6.2 0 8.86
Concourse Set B -UDCon9-4 Combination X 0.000294 146 13.56 48.58 8.86
Concourse Set B -UDCon9-4 Combination Y 7.7E-05 420 3.15 0 8.86
Concourse Set B -UDCon10-1 Combination X 0.000204 146 13.56 48.58 8.86
Concourse Set B -UDCon10-2 Combination X 0.000208 146 13.56 48.58 8.86
Concourse Set B -UDCon10-2 Combination Y 5.6E-05 420 3.15 0 8.86
Concourse Set B -UDCon10-3 Combination X 0.000337 277 -6.2 0 8.86
Concourse Set B -UDCon10-4 Combination X 0.000219 146 13.56 48.58 8.86
Concourse Set B -UDCon10-4 Combination Y 7.4E-05 420 3.15 0 8.86
Concourse Set B-ENVE Combination Max X 0.000204 146 13.56 48.58 8.86
Concourse Set B-ENVE Combination Max Y 5.6E-05 420 3.15 0 8.86
Concourse Set B-ENVE Combination Min X 0.000428 277 -6.2 0 8.86
Concourse Set B-ENVE Combination Min Y 7.7E-05 420 3.15 0 8.86
Concourse Set C -UDCon1 Combination X 0.000214 146 13.56 48.58 8.86
Concourse Set C -UDCon2 Combination X 0.000288 146 13.56 48.58 8.86
Concourse Set C -UDCon3 Combination Max X 0.000288 146 13.56 48.58 8.86
Concourse Set C -UDCon3 Combination Min X 0.000288 146 13.56 48.58 8.86
Concourse Set C -UDCon4 Combination Max X 0.000265 146 13.56 48.58 8.86
Concourse Set C -UDCon4 Combination Min X 0.000265 146 13.56 48.58 8.86
Concourse Set C -UDCon5 Combination Max X 0.000214 146 13.56 48.58 8.86
Concourse Set C -UDCon5 Combination Min X 0.000214 146 13.56 48.58 8.86
Concourse Set C -UDCon6-1 Combination X 0.000278 146 13.56 48.58 8.86
Concourse Set C -UDCon6-2 Combination X 0.000282 146 13.56 48.58 8.86
Concourse Set C -UDCon6-2 Combination Y 5.7E-05 420 3.15 0 8.86
Concourse Set C -UDCon6-3 Combination X 0.000382 277 -6.2 0 8.86
Concourse Set C -UDCon6-4 Combination X 0.000293 146 13.56 48.58 8.86
Concourse Set C -UDCon6-4 Combination Y 7.3E-05 420 3.15 0 8.86
Concourse Set C -UDCon7-1 Combination X 0.000256 146 13.56 48.58 8.86
Concourse Set C -UDCon7-2 Combination X 0.00026 146 13.56 48.58 8.86
Concourse Set C -UDCon7-2 Combination Y 5.6E-05 420 3.15 0 8.86
Concourse Set C -UDCon7-3 Combination X 0.000369 277 -6.2 0 8.86
Concourse Set C -UDCon7-4 Combination X 0.000271 146 13.56 48.58 8.86
Concourse Set C -UDCon7-4 Combination Y 7.3E-05 420 3.15 0 8.86
Concourse Set C -UDCon8-1 Combination X 0.000204 146 13.56 48.58 8.86
Step X Y Z
Story Output Case Case Type Direction Drift Label
Type m m m
Concourse Set C -UDCon8-2 Combination X 0.000208 146 13.56 48.58 8.86
Concourse Set C -UDCon8-2 Combination Y 5.6E-05 420 3.15 0 8.86
Concourse Set C -UDCon8-3 Combination X 0.000337 277 -6.2 0 8.86
Concourse Set C -UDCon8-4 Combination X 0.000219 146 13.56 48.58 8.86
Concourse Set C -UDCon8-4 Combination Y 7.4E-05 420 3.15 0 8.86
Concourse Set C- ENVE Combination Max X 0.000204 146 13.56 48.58 8.86
Concourse Set C- ENVE Combination Max Y 5.7E-05 420 3.15 0 8.86
Concourse Set C- ENVE Combination Min X 0.000382 277 -6.2 0 8.86
Concourse Set C- ENVE Combination Min Y 7.4E-05 420 3.15 0 8.86
Ground- walkway Rf DL LinStatic X 2.5E-05 50 5 25.03 5.93
Ground- walkway Rf DL LinStatic Y 2.9E-05 24 5 10.18 5.93
Ground- walkway Rf SDL LinStatic X 8E-06 81 5 40.4 5.93
Ground- walkway Rf SDL LinStatic Y 6E-06 24 5 10.18 5.93
Ground- walkway Rf LL LinStatic X 1E-05 50 5 25.03 5.93
Ground- walkway Rf LL LinStatic Y 1.1E-05 24 5 10.18 5.93
Ground- walkway Rf Acci Fx LinStatic X 2.568E-07 51 13.56 25.03 5.93
Ground- walkway Rf Acci Fx LinStatic Y 4.706E-07 50 5 25.03 5.93
Ground- walkway Rf Acci Fy LinStatic X 1E-06 26 13.56 10.18 5.93
Ground- walkway Rf Acci Fy LinStatic Y 1E-06 15 5 5 5.93
Ground- walkway Rf NL-0deg LinStatic X 4E-06 41 5 19.85 5.93
Ground- walkway Rf NL-90deg LinStatic Y 1.1E-05 41 5 19.85 5.93
Ground- walkway Rf NL-180deg LinStatic X 4E-06 41 5 19.85 5.93
Ground- walkway Rf NL-270deg LinStatic Y 1.1E-05 41 5 19.85 5.93
Ground- walkway Rf Set B -UDCon1 Combination X 4.4E-05 50 5 25.03 5.93
Ground- walkway Rf Set B -UDCon1 Combination Y 4.8E-05 24 5 10.18 5.93
Ground- walkway Rf SLS 1 Combination X 4.3E-05 50 5 25.03 5.93
Ground- walkway Rf SLS 1 Combination Y 4.6E-05 24 5 10.18 5.93
Ground- walkway Rf ALL DL Combination X 3.2E-05 50 5 25.03 5.93
Ground- walkway Rf ALL DL Combination Y 3.5E-05 24 5 10.18 5.93
Ground- walkway Rf ALL LL Combination X 1E-05 50 5 25.03 5.93
Ground- walkway Rf ALL LL Combination Y 1.1E-05 24 5 10.18 5.93
Ground- walkway Rf ULS-A1 Combination X 3.7E-05 50 5 25.03 5.93
Ground- walkway Rf ULS-A1 Combination Y 4E-05 24 5 10.18 5.93
Ground- walkway Rf ULS-A2 Combination X 3.6E-05 50 5 25.03 5.93
Ground- walkway Rf ULS-A2 Combination Y 3.9E-05 24 5 10.18 5.93
Ground- walkway Rf DCmpD1 Combination X 3.2E-05 50 5 25.03 5.93
Ground- walkway Rf DCmpD1 Combination Y 3.5E-05 24 5 10.18 5.93
Ground- walkway Rf DCmpD2 Combination X 4.3E-05 50 5 25.03 5.93
Ground- walkway Rf DCmpD2 Combination Y 4.6E-05 24 5 10.18 5.93
Ground- walkway Rf DCmpS1 Combination X 4.4E-05 50 5 25.03 5.93
Ground- walkway Rf DCmpS1 Combination Y 4.8E-05 24 5 10.18 5.93
Ground- walkway Rf DCmpS2 Combination X 5.9E-05 50 5 25.03 5.93
Ground- walkway Rf DCmpS2 Combination Y 6.4E-05 24 5 10.18 5.93
Ground- walkway Rf DCmpC1 Combination X 3.8E-05 50 5 25.03 5.93
Ground- walkway Rf DCmpC1 Combination Y 4.4E-05 24 5 10.18 5.93
Step X Y Z
Story Output Case Case Type Direction Drift Label
Type m m m
Ground- walkway Rf Geo-Com1 Combination X 5.9E-05 50 5 25.03 5.93
Ground- walkway Rf Geo-Com1 Combination Y 6.4E-05 24 5 10.18 5.93
Ground- walkway Rf Geo-Com2 Combination X 4.6E-05 50 5 25.03 5.93
Ground- walkway Rf Geo-Com2 Combination Y 5E-05 24 5 10.18 5.93
Ground- walkway Rf SLS 2 Combination Max X 4.3E-05 50 5 25.03 5.93
Ground- walkway Rf SLS 2 Combination Max Y 4.6E-05 24 5 10.18 5.93
Ground- walkway Rf SLS 2 Combination Min X 4.3E-05 50 5 25.03 5.93
Ground- walkway Rf SLS 2 Combination Min Y 4.6E-05 24 5 10.18 5.93
Ground- walkway Rf SLS 3 Combination Max X 4E-05 50 5 25.03 5.93
Ground- walkway Rf SLS 3 Combination Max Y 4.3E-05 24 5 10.18 5.93
Ground- walkway Rf SLS 3 Combination Min X 4E-05 50 5 25.03 5.93
Ground- walkway Rf SLS 3 Combination Min Y 4.3E-05 24 5 10.18 5.93
Ground- walkway Rf SLS 4 Combination Max X 3.2E-05 50 5 25.03 5.93
Ground- walkway Rf SLS 4 Combination Max Y 3.5E-05 24 5 10.18 5.93
Ground- walkway Rf SLS 4 Combination Min X 3.2E-05 50 5 25.03 5.93
Ground- walkway Rf SLS 4 Combination Min Y 3.5E-05 24 5 10.18 5.93
Ground- walkway Rf SLS ENVE Combination Max X 3.2E-05 50 5 25.03 5.93
Ground- walkway Rf SLS ENVE Combination Max Y 4.6E-05 24 5 10.18 5.93
Ground- walkway Rf SLS ENVE Combination Min X 4.3E-05 50 5 25.03 5.93
Ground- walkway Rf SLS ENVE Combination Min Y 3.5E-05 24 5 10.18 5.93
Ground- walkway Rf Set B -UDCon2 Combination X 5.9E-05 50 5 25.03 5.93
Ground- walkway Rf Set B -UDCon2 Combination Y 6.4E-05 24 5 10.18 5.93
Ground- walkway Rf Set B -UDCon3 Combination Max X 5.9E-05 50 5 25.03 5.93
Ground- walkway Rf Set B -UDCon3 Combination Max Y 6.4E-05 24 5 10.18 5.93
Ground- walkway Rf Set B -UDCon3 Combination Min X 5.9E-05 50 5 25.03 5.93
Ground- walkway Rf Set B -UDCon3 Combination Min Y 6.4E-05 24 5 10.18 5.93
Ground- walkway Rf Set B -UDCon4 Combination Max X 5.5E-05 50 5 25.03 5.93
Ground- walkway Rf Set B -UDCon4 Combination Max Y 5.9E-05 24 5 10.18 5.93
Ground- walkway Rf Set B -UDCon4 Combination Min X 5.5E-05 50 5 25.03 5.93
Ground- walkway Rf Set B -UDCon4 Combination Min Y 5.9E-05 24 5 10.18 5.93
Ground- walkway Rf Set B -UDCon5 Combination Max X 4.4E-05 50 5 25.03 5.93
Ground- walkway Rf Set B -UDCon5 Combination Max Y 4.8E-05 24 5 10.18 5.93
Ground- walkway Rf Set B -UDCon5 Combination Min X 4.4E-05 50 5 25.03 5.93
Ground- walkway Rf Set B -UDCon5 Combination Min Y 4.8E-05 24 5 10.18 5.93
Ground- walkway Rf Set B -UDCon6 Combination Max X 3.2E-05 50 5 25.03 5.93
Ground- walkway Rf Set B -UDCon6 Combination Max Y 3.5E-05 24 5 10.18 5.93
Ground- walkway Rf Set B -UDCon6 Combination Min X 3.2E-05 50 5 25.03 5.93
Ground- walkway Rf Set B -UDCon6 Combination Min Y 3.5E-05 24 5 10.18 5.93
Ground- walkway Rf Set B -UDCon7-1 Combination X 6.3E-05 50 5 25.03 5.93
Ground- walkway Rf Set B -UDCon7-1 Combination Y 6.5E-05 24 5 10.18 5.93
Ground- walkway Rf Set B -UDCon7-2 Combination X 5.9E-05 50 5 25.03 5.93
Ground- walkway Rf Set B -UDCon7-2 Combination Y 5.7E-05 24 5 10.18 5.93
Ground- walkway Rf Set B -UDCon7-3 Combination X 5.6E-05 50 5 25.03 5.93
Ground- walkway Rf Set B -UDCon7-3 Combination Y 6.4E-05 24 5 10.18 5.93
Ground- walkway Rf Set B -UDCon7-4 Combination X 6E-05 50 5 25.03 5.93
Step X Y Z
Story Output Case Case Type Direction Drift Label
Type m m m
Ground- walkway Rf Set B -UDCon7-4 Combination Y 7.1E-05 24 5 10.18 5.93
Ground- walkway Rf Set B -UDCon8-1 Combination X 5.8E-05 50 5 25.03 5.93
Ground- walkway Rf Set B -UDCon8-1 Combination Y 6E-05 24 5 10.18 5.93
Ground- walkway Rf Set B -UDCon8-2 Combination X 5.4E-05 50 5 25.03 5.93
Ground- walkway Rf Set B -UDCon8-2 Combination Y 5.2E-05 24 5 10.18 5.93
Ground- walkway Rf Set B -UDCon8-3 Combination X 5.1E-05 50 5 25.03 5.93
Ground- walkway Rf Set B -UDCon8-3 Combination Y 5.9E-05 24 5 10.18 5.93
Ground- walkway Rf Set B -UDCon8-4 Combination X 5.5E-05 50 5 25.03 5.93
Ground- walkway Rf Set B -UDCon8-4 Combination Y 6.6E-05 24 5 10.18 5.93
Ground- walkway Rf Set B -UDCon9-1 Combination X 4.7E-05 50 5 25.03 5.93
Ground- walkway Rf Set B -UDCon9-1 Combination Y 4.8E-05 24 5 10.18 5.93
Ground- walkway Rf Set B -UDCon9-2 Combination X 4.3E-05 50 5 25.03 5.93
Ground- walkway Rf Set B -UDCon9-2 Combination Y 4.1E-05 24 5 10.18 5.93
Ground- walkway Rf Set B -UDCon9-3 Combination X 4E-05 50 5 25.03 5.93
Ground- walkway Rf Set B -UDCon9-3 Combination Y 4.8E-05 24 5 10.18 5.93
Ground- walkway Rf Set B -UDCon9-4 Combination X 4.4E-05 50 5 25.03 5.93
Ground- walkway Rf Set B -UDCon9-4 Combination Y 5.5E-05 24 5 10.18 5.93
Ground- walkway Rf Set B -UDCon10-1 Combination X 3.6E-05 50 5 25.03 5.93
Ground- walkway Rf Set B -UDCon10-1 Combination Y 3.6E-05 24 5 10.18 5.93
Ground- walkway Rf Set B -UDCon10-2 Combination X 3.2E-05 50 5 25.03 5.93
Ground- walkway Rf Set B -UDCon10-2 Combination Y 2.8E-05 24 5 10.18 5.93
Ground- walkway Rf Set B -UDCon10-3 Combination X 2.9E-05 50 5 25.03 5.93
Ground- walkway Rf Set B -UDCon10-3 Combination Y 3.5E-05 24 5 10.18 5.93
Ground- walkway Rf Set B -UDCon10-4 Combination X 3.3E-05 50 5 25.03 5.93
Ground- walkway Rf Set B -UDCon10-4 Combination Y 4.3E-05 24 5 10.18 5.93
Ground- walkway Rf Set B-ENVE Combination Max X 2.9E-05 50 5 25.03 5.93
Ground- walkway Rf Set B-ENVE Combination Max Y 7.1E-05 24 5 10.18 5.93
Ground- walkway Rf Set B-ENVE Combination Min X 6.3E-05 50 5 25.03 5.93
Ground- walkway Rf Set C -UDCon1 Combination X 3.2E-05 50 5 25.03 5.93
Ground- walkway Rf Set C -UDCon1 Combination Y 3.5E-05 24 5 10.18 5.93
Ground- walkway Rf Set C -UDCon2 Combination X 4.6E-05 50 5 25.03 5.93
Ground- walkway Rf Set C -UDCon2 Combination Y 5E-05 24 5 10.18 5.93
Ground- walkway Rf Set C -UDCon3 Combination Max X 4.6E-05 50 5 25.03 5.93
Ground- walkway Rf Set C -UDCon3 Combination Max Y 5E-05 24 5 10.18 5.93
Ground- walkway Rf Set C -UDCon3 Combination Min X 4.6E-05 50 5 25.03 5.93
Ground- walkway Rf Set C -UDCon3 Combination Min Y 5E-05 24 5 10.18 5.93
Ground- walkway Rf Set C -UDCon4 Combination Max X 4.2E-05 50 5 25.03 5.93
Ground- walkway Rf Set C -UDCon4 Combination Max Y 4.5E-05 24 5 10.18 5.93
Ground- walkway Rf Set C -UDCon4 Combination Min X 4.2E-05 50 5 25.03 5.93
Ground- walkway Rf Set C -UDCon4 Combination Min Y 4.5E-05 24 5 10.18 5.93
Ground- walkway Rf Set C -UDCon5 Combination Max X 3.2E-05 50 5 25.03 5.93
Ground- walkway Rf Set C -UDCon5 Combination Max Y 3.5E-05 24 5 10.18 5.93
Ground- walkway Rf Set C -UDCon5 Combination Min X 3.2E-05 50 5 25.03 5.93
Ground- walkway Rf Set C -UDCon5 Combination Min Y 3.5E-05 24 5 10.18 5.93
Ground- walkway Rf Set C -UDCon6-1 Combination X 5E-05 50 5 25.03 5.93
Step X Y Z
Story Output Case Case Type Direction Drift Label
Type m m m
Ground- walkway Rf Set C -UDCon6-1 Combination Y 5E-05 24 5 10.18 5.93
Ground- walkway Rf Set C -UDCon6-2 Combination X 4.6E-05 50 5 25.03 5.93
Ground- walkway Rf Set C -UDCon6-2 Combination Y 4.3E-05 24 5 10.18 5.93
Ground- walkway Rf Set C -UDCon6-3 Combination X 4.2E-05 50 5 25.03 5.93
Ground- walkway Rf Set C -UDCon6-3 Combination Y 4.9E-05 24 5 10.18 5.93
Ground- walkway Rf Set C -UDCon6-4 Combination X 4.6E-05 50 5 25.03 5.93
Ground- walkway Rf Set C -UDCon6-4 Combination Y 5.7E-05 24 5 10.18 5.93
Ground- walkway Rf Set C -UDCon7-1 Combination X 4.5E-05 50 5 25.03 5.93
Ground- walkway Rf Set C -UDCon7-1 Combination Y 4.6E-05 24 5 10.18 5.93
Ground- walkway Rf Set C -UDCon7-2 Combination X 4.2E-05 50 5 25.03 5.93
Ground- walkway Rf Set C -UDCon7-2 Combination Y 3.8E-05 24 5 10.18 5.93
Ground- walkway Rf Set C -UDCon7-3 Combination X 3.8E-05 50 5 25.03 5.93
Ground- walkway Rf Set C -UDCon7-3 Combination Y 4.5E-05 24 5 10.18 5.93
Ground- walkway Rf Set C -UDCon7-4 Combination X 4.2E-05 50 5 25.03 5.93
Ground- walkway Rf Set C -UDCon7-4 Combination Y 5.2E-05 24 5 10.18 5.93
Ground- walkway Rf Set C -UDCon8-1 Combination X 3.6E-05 50 5 25.03 5.93
Ground- walkway Rf Set C -UDCon8-1 Combination Y 3.6E-05 24 5 10.18 5.93
Ground- walkway Rf Set C -UDCon8-2 Combination X 3.2E-05 50 5 25.03 5.93
Ground- walkway Rf Set C -UDCon8-2 Combination Y 2.8E-05 24 5 10.18 5.93
Ground- walkway Rf Set C -UDCon8-3 Combination X 2.9E-05 50 5 25.03 5.93
Ground- walkway Rf Set C -UDCon8-3 Combination Y 3.5E-05 24 5 10.18 5.93
Ground- walkway Rf Set C -UDCon8-4 Combination X 3.3E-05 50 5 25.03 5.93
Ground- walkway Rf Set C -UDCon8-4 Combination Y 4.3E-05 24 5 10.18 5.93
Ground- walkway Rf Set C- ENVE Combination Max X 2.9E-05 50 5 25.03 5.93
Ground- walkway Rf Set C- ENVE Combination Max Y 5.7E-05 24 5 10.18 5.93
Ground- walkway Rf Set C- ENVE Combination Min X 5E-05 50 5 25.03 5.93
Ground- walkway Rf Set C- ENVE Combination Min Y 2.8E-05 24 5 10.18 5.93
Ground DL LinStatic X 1.8E-05 113 5 9.18 3
Ground DL LinStatic Y 2.8E-05 113 5 9.18 3
Ground SDL LinStatic X 1.1E-05 146 13.56 48.58 3
Ground SDL LinStatic Y 1.2E-05 113 5 9.18 3
Ground LL LinStatic X 1.3E-05 401 6.31 0 3
Ground LL LinStatic Y 1.6E-05 113 5 9.18 3
Ground Acci Fx LinStatic X 3E-06 92 6.1 48.58 3
Ground Acci Fx LinStatic Y 3E-06 51 13.56 25.03 3
Ground Acci Fy LinStatic X 9E-06 92 6.1 48.58 3
Ground Acci Fy LinStatic Y 1.2E-05 83 13.56 40.4 3
Ground NL-0deg LinStatic X 3.7E-05 177 13.56 0 3
Ground NL-90deg LinStatic Y 6.4E-05 146 13.56 48.58 3
Ground NL-180deg LinStatic X 3.7E-05 177 13.56 0 3
Ground NL-270deg LinStatic Y 6.4E-05 146 13.56 48.58 3
Ground Set B -UDCon1 Combination X 3.7E-05 146 13.56 48.58 3
Ground Set B -UDCon1 Combination Y 5.5E-05 113 5 9.18 3
Ground SLS 1 Combination X 3.9E-05 401 6.31 0 3
Ground SLS 1 Combination Y 5.6E-05 113 5 9.18 3
Step X Y Z
Story Output Case Case Type Direction Drift Label
Type m m m
Ground ALL DL Combination X 2.8E-05 146 13.56 48.58 3
Ground ALL DL Combination Y 4.1E-05 113 5 9.18 3
Ground ALL LL Combination X 1.3E-05 401 6.31 0 3
Ground ALL LL Combination Y 1.6E-05 113 5 9.18 3
Ground ULS-A1 Combination X 3.5E-05 146 13.56 48.58 3
Ground ULS-A1 Combination Y 4.9E-05 113 5 9.18 3
Ground ULS-A2 Combination X 3.7E-05 401 6.31 0 3
Ground ULS-A2 Combination Y 3.8E-05 113 5 9.18 3
Ground DCmpD1 Combination X 2.8E-05 146 13.56 48.58 3
Ground DCmpD1 Combination Y 4.1E-05 113 5 9.18 3
Ground DCmpD2 Combination X 3.9E-05 401 6.31 0 3
Ground DCmpD2 Combination Y 5.6E-05 113 5 9.18 3
Ground DCmpS1 Combination X 3.7E-05 146 13.56 48.58 3
Ground DCmpS1 Combination Y 5.5E-05 113 5 9.18 3
Ground DCmpS2 Combination X 5.5E-05 401 6.31 0 3
Ground DCmpS2 Combination Y 7.8E-05 113 5 9.18 3
Ground DCmpC1 Combination X 2.7E-05 113 5 9.18 3
Ground DCmpC1 Combination Y 4.3E-05 113 5 9.18 3
Ground Geo-Com1 Combination X 5.5E-05 401 6.31 0 3
Ground Geo-Com1 Combination Y 7.8E-05 113 5 9.18 3
Ground Geo-Com2 Combination X 4.3E-05 401 6.31 0 3
Ground Geo-Com2 Combination Y 6.1E-05 113 5 9.18 3
Ground SLS 2 Combination Max X 3.9E-05 401 6.31 0 3
Ground SLS 2 Combination Max Y 5.6E-05 113 5 9.18 3
Ground SLS 2 Combination Min X 3.9E-05 401 6.31 0 3
Ground SLS 2 Combination Min Y 5.6E-05 113 5 9.18 3
Ground SLS 3 Combination Max X 3.5E-05 401 6.31 0 3
Ground SLS 3 Combination Max Y 5.2E-05 113 5 9.18 3
Ground SLS 3 Combination Min X 3.5E-05 401 6.31 0 3
Ground SLS 3 Combination Min Y 5.2E-05 113 5 9.18 3
Ground SLS 4 Combination Max X 2.8E-05 146 13.56 48.58 3
Ground SLS 4 Combination Max Y 4.1E-05 113 5 9.18 3
Ground SLS 4 Combination Min X 2.8E-05 146 13.56 48.58 3
Ground SLS 4 Combination Min Y 4.1E-05 113 5 9.18 3
Ground SLS ENVE Combination Max X 3.9E-05 401 6.31 0 3
Ground SLS ENVE Combination Max Y 4.1E-05 113 5 9.18 3
Ground SLS ENVE Combination Min X 2.8E-05 146 13.56 48.58 3
Ground SLS ENVE Combination Min Y 5.6E-05 113 5 9.18 3
Ground Set B -UDCon2 Combination X 5.5E-05 401 6.31 0 3
Ground Set B -UDCon2 Combination Y 7.8E-05 113 5 9.18 3
Ground Set B -UDCon3 Combination Max X 5.5E-05 401 6.31 0 3
Ground Set B -UDCon3 Combination Max Y 7.8E-05 113 5 9.18 3
Ground Set B -UDCon3 Combination Min X 5.5E-05 401 6.31 0 3
Ground Set B -UDCon3 Combination Min Y 7.8E-05 113 5 9.18 3
Ground Set B -UDCon4 Combination Max X 4.9E-05 401 6.31 0 3
Step X Y Z
Story Output Case Case Type Direction Drift Label
Type m m m
Ground Set B -UDCon4 Combination Max Y 7.1E-05 113 5 9.18 3
Ground Set B -UDCon4 Combination Min X 4.9E-05 401 6.31 0 3
Ground Set B -UDCon4 Combination Min Y 7.1E-05 113 5 9.18 3
Ground Set B -UDCon5 Combination Max X 3.7E-05 146 13.56 48.58 3
Ground Set B -UDCon5 Combination Max Y 5.5E-05 113 5 9.18 3
Ground Set B -UDCon5 Combination Min X 3.7E-05 146 13.56 48.58 3
Ground Set B -UDCon5 Combination Min Y 5.5E-05 113 5 9.18 3
Ground Set B -UDCon6 Combination Max X 2.8E-05 146 13.56 48.58 3
Ground Set B -UDCon6 Combination Max Y 4.1E-05 113 5 9.18 3
Ground Set B -UDCon6 Combination Min X 2.8E-05 146 13.56 48.58 3
Ground Set B -UDCon6 Combination Min Y 4.1E-05 113 5 9.18 3
Ground Set B -UDCon7-1 Combination X 9.1E-05 401 6.31 0 3
Ground Set B -UDCon7-1 Combination Y 8E-05 113 5 9.18 3
Ground Set B -UDCon7-2 Combination X 7.4E-05 401 6.31 0 3
Ground Set B -UDCon7-2 Combination Y 2.1E-05 113 5 9.18 3
Ground Set B -UDCon7-3 Combination X 3.1E-05 81 5 40.4 3
Ground Set B -UDCon7-3 Combination Y 7.7E-05 113 5 9.18 3
Ground Set B -UDCon7-4 Combination X 7.4E-05 146 13.56 48.58 3
Ground Set B -UDCon7-4 Combination Y 0.000135 113 5 9.18 3
Ground Set B -UDCon8-1 Combination X 8.6E-05 401 6.31 0 3
Ground Set B -UDCon8-1 Combination Y 7.3E-05 113 5 9.18 3
Ground Set B -UDCon8-2 Combination X 6.9E-05 401 6.31 0 3
Ground Set B -UDCon8-3 Combination X 2.6E-05 81 5 40.4 3
Ground Set B -UDCon8-3 Combination Y 7E-05 113 5 9.18 3
Ground Set B -UDCon8-4 Combination X 6.9E-05 146 13.56 48.58 3
Ground Set B -UDCon8-4 Combination Y 0.000128 113 5 9.18 3
Ground Set B -UDCon9-1 Combination X 7.2E-05 401 6.31 0 3
Ground Set B -UDCon9-1 Combination Y 5.6E-05 113 5 9.18 3
Ground Set B -UDCon9-2 Combination X 5.5E-05 401 6.31 0 3
Ground Set B -UDCon9-2 Combination Y 1.9E-05 83 13.56 40.4 3
Ground Set B -UDCon9-3 Combination X 1.5E-05 81 5 40.4 3
Ground Set B -UDCon9-3 Combination Y 5.3E-05 113 5 9.18 3
Ground Set B -UDCon9-4 Combination X 5.8E-05 146 13.56 48.58 3
Ground Set B -UDCon9-4 Combination Y 0.000113 51 13.56 25.03 3
Ground Set B -UDCon10-1 Combination X 6.3E-05 401 6.31 0 3
Ground Set B -UDCon10-1 Combination Y 4.2E-05 113 5 9.18 3
Ground Set B -UDCon10-2 Combination X 4.6E-05 401 6.31 0 3
Ground Set B -UDCon10-2 Combination Y 3.1E-05 83 13.56 40.4 3
Ground Set B -UDCon10-3 Combination Y 4.1E-05 16 13.56 5 3
Ground Set B -UDCon10-4 Combination X 4.8E-05 146 13.56 48.58 3
Ground Set B -UDCon10-4 Combination Y 0.0001 51 13.56 25.03 3
Ground Set B-ENVE Combination Max X 9.1E-05 401 6.31 0 3
Ground Set B-ENVE Combination Max Y 3.1E-05 83 13.56 40.4 3
Ground Set B-ENVE Combination Min Y 0.000135 113 5 9.18 3
Ground Set C -UDCon1 Combination X 2.8E-05 146 13.56 48.58 3
Step X Y Z
Story Output Case Case Type Direction Drift Label
Type m m m
Ground Set C -UDCon1 Combination Y 4.1E-05 113 5 9.18 3
Ground Set C -UDCon2 Combination X 4.3E-05 401 6.31 0 3
Ground Set C -UDCon2 Combination Y 6.1E-05 113 5 9.18 3
Ground Set C -UDCon3 Combination Max X 4.3E-05 401 6.31 0 3
Ground Set C -UDCon3 Combination Max Y 6.1E-05 113 5 9.18 3
Ground Set C -UDCon3 Combination Min X 4.3E-05 401 6.31 0 3
Ground Set C -UDCon3 Combination Min Y 6.1E-05 113 5 9.18 3
Ground Set C -UDCon4 Combination Max X 3.8E-05 401 6.31 0 3
Ground Set C -UDCon4 Combination Max Y 5.5E-05 113 5 9.18 3
Ground Set C -UDCon4 Combination Min X 3.8E-05 401 6.31 0 3
Ground Set C -UDCon4 Combination Min Y 5.5E-05 113 5 9.18 3
Ground Set C -UDCon5 Combination Max X 2.8E-05 146 13.56 48.58 3
Ground Set C -UDCon5 Combination Max Y 4.1E-05 113 5 9.18 3
Ground Set C -UDCon5 Combination Min X 2.8E-05 146 13.56 48.58 3
Ground Set C -UDCon5 Combination Min Y 4.1E-05 113 5 9.18 3
Ground Set C -UDCon6-1 Combination X 8E-05 401 6.31 0 3
Ground Set C -UDCon6-1 Combination Y 6.3E-05 113 5 9.18 3
Ground Set C -UDCon6-2 Combination X 6.2E-05 401 6.31 0 3
Ground Set C -UDCon6-2 Combination Y 1.4E-05 83 13.56 40.4 3
Ground Set C -UDCon6-3 Combination X 1.9E-05 74 5 35.22 3
Ground Set C -UDCon6-3 Combination Y 5.9E-05 113 5 9.18 3
Ground Set C -UDCon6-4 Combination X 6.2E-05 146 13.56 48.58 3
Ground Set C -UDCon6-4 Combination Y 0.000118 113 5 9.18 3
Ground Set C -UDCon7-1 Combination X 7.5E-05 401 6.31 0 3
Ground Set C -UDCon7-1 Combination Y 5.6E-05 113 5 9.18 3
Ground Set C -UDCon7-2 Combination X 5.8E-05 401 6.31 0 3
Ground Set C -UDCon7-2 Combination Y 1.9E-05 83 13.56 40.4 3
Ground Set C -UDCon7-3 Combination X 1.5E-05 74 5 35.22 3
Ground Set C -UDCon7-3 Combination Y 5.3E-05 113 5 9.18 3
Ground Set C -UDCon7-4 Combination X 5.8E-05 146 13.56 48.58 3
Ground Set C -UDCon7-4 Combination Y 0.000113 51 13.56 25.03 3
Ground Set C -UDCon8-1 Combination X 6.3E-05 401 6.31 0 3
Ground Set C -UDCon8-1 Combination Y 4.2E-05 113 5 9.18 3
Ground Set C -UDCon8-2 Combination X 4.6E-05 401 6.31 0 3
Ground Set C -UDCon8-2 Combination Y 3.1E-05 83 13.56 40.4 3
Ground Set C -UDCon8-3 Combination Y 4.1E-05 16 13.56 5 3
Ground Set C -UDCon8-4 Combination X 4.8E-05 146 13.56 48.58 3
Ground Set C -UDCon8-4 Combination Y 0.0001 51 13.56 25.03 3
Ground Set C- ENVE Combination Max X 8E-05 401 6.31 0 3
Ground Set C- ENVE Combination Max Y 3.1E-05 83 13.56 40.4 3
Ground Set C- ENVE Combination Min Y 0.000118 113 5 9.18 3
Step P VX VY T
Story Output Case Case Type Location
Type kN kN kN kN-m
Upper Platform Geo-Com1 Combination Bottom 5428.73 130.92 50.58 -4767.02
Upper Platform Geo-Com2 Combination Top 2009.06 101.82 39.23 -3707.81
Upper Platform Geo-Com2 Combination Bottom 4079.31 101.82 39.23 -3707.81
Upper Platform SLS 2 Combination Max Top 1916.9 94.14 36.43 -3427.2
Upper Platform SLS 2 Combination Max Bottom 3987.14 94.14 36.43 -3427.2
Upper Platform SLS 2 Combination Min Top 1916.9 94.14 36.43 -3427.2
Upper Platform SLS 2 Combination Min Bottom 3987.14 94.14 36.43 -3427.2
Upper Platform SLS 3 Combination Max Top 1824.73 86.45 33.63 -3146.59
Upper Platform SLS 3 Combination Max Bottom 3894.98 86.45 33.63 -3146.59
Upper Platform SLS 3 Combination Min Top 1824.73 86.45 33.63 -3146.59
Upper Platform SLS 3 Combination Min Bottom 3894.98 86.45 33.63 -3146.59
Upper Platform SLS 4 Combination Max Top 1609.68 68.53 27.09 -2491.83
Upper Platform SLS 4 Combination Max Bottom 3679.92 68.53 27.09 -2491.83
Upper Platform SLS 4 Combination Min Top 1609.68 68.53 27.09 -2491.83
Upper Platform SLS 4 Combination Min Bottom 3679.92 68.53 27.09 -2491.83
Upper Platform SLS ENVE Combination Max Top 1916.9 94.14 36.43 -2491.83
Upper Platform SLS ENVE Combination Max Bottom 3987.14 94.14 36.43 -2491.83
Upper Platform SLS ENVE Combination Min Top 1609.68 68.53 27.09 -3427.2
Upper Platform SLS ENVE Combination Min Bottom 3679.92 68.53 27.09 -3427.2
Upper Platform Set B -UDCon2 Combination Top 2633.89 130.92 50.58 -4767.02
Upper Platform Set B -UDCon2 Combination Bottom 5428.73 130.92 50.58 -4767.02
Upper Platform Set B -UDCon3 Combination Max Top 2633.89 130.92 50.58 -4767.02
Upper Platform Set B -UDCon3 Combination Max Bottom 5428.73 130.92 50.58 -4767.02
Upper Platform Set B -UDCon3 Combination Min Top 2633.89 130.92 50.58 -4767.02
Upper Platform Set B -UDCon3 Combination Min Bottom 5428.73 130.92 50.58 -4767.02
Upper Platform Set B -UDCon4 Combination Max Top 2495.64 119.4 46.38 -4346.1
Upper Platform Set B -UDCon4 Combination Max Bottom 5290.48 119.4 46.38 -4346.11
Upper Platform Set B -UDCon4 Combination Min Top 2495.64 119.4 46.38 -4346.1
Upper Platform Set B -UDCon4 Combination Min Bottom 5290.48 119.4 46.38 -4346.11
Upper Platform Set B -UDCon5 Combination Max Top 2173.06 92.52 36.58 -3363.97
Upper Platform Set B -UDCon5 Combination Max Bottom 4967.9 92.52 36.58 -3363.97
Upper Platform Set B -UDCon5 Combination Min Top 2173.06 92.52 36.58 -3363.97
Upper Platform Set B -UDCon5 Combination Min Bottom 4967.9 92.52 36.58 -3363.97
Upper Platform Set B -UDCon6 Combination Max Top 1609.68 68.53 27.09 -2491.83
Upper Platform Set B -UDCon6 Combination Max Bottom 3679.92 68.53 27.09 -2491.83
Upper Platform Set B -UDCon6 Combination Min Top 1609.68 68.53 27.09 -2491.83
Upper Platform Set B -UDCon6 Combination Min Bottom 3679.92 68.53 27.09 -2491.83
Upper Platform Set B -UDCon7-1 Combination Top 2633.88 112.49 50.42 -4353.07
Upper Platform Set B -UDCon7-1 Combination Bottom 5428.71 81.44 50.42 -3646.22
Upper Platform Set B -UDCon7-2 Combination Top 2633.9 130.91 32.4 -4934.9
Upper Platform Set B -UDCon7-2 Combination Bottom 5428.73 130.91 1.34 -5221.56
Upper Platform Set B -UDCon7-3 Combination Top 2633.91 149.35 50.74 -5180.96
Upper Platform Set B -UDCon7-3 Combination Bottom 5428.74 180.41 50.74 -5887.82
Upper Platform Set B -UDCon7-4 Combination Top 2633.89 130.94 68.77 -4599.13
Step P VX VY T
Story Output Case Case Type Location
Type kN kN kN kN-m
Upper Platform Set B -UDCon7-4 Combination Bottom 5428.72 130.94 99.82 -4312.48
Upper Platform Set B -UDCon8-1 Combination Top 2495.63 100.97 46.22 -3932.16
Upper Platform Set B -UDCon8-1 Combination Bottom 5290.46 69.92 46.22 -3225.31
Upper Platform Set B -UDCon8-2 Combination Top 2495.65 119.39 28.19 -4513.99
Upper Platform Set B -UDCon8-2 Combination Bottom 5290.48 119.39 -2.86 -4800.65
Upper Platform Set B -UDCon8-3 Combination Top 2495.66 137.83 46.54 -4760.05
Upper Platform Set B -UDCon8-3 Combination Bottom 5290.49 168.89 46.54 -5466.91
Upper Platform Set B -UDCon8-4 Combination Top 2495.64 119.42 64.57 -4178.22
Upper Platform Set B -UDCon8-4 Combination Bottom 5290.47 119.42 95.62 -3891.57
Upper Platform Set B -UDCon9-1 Combination Top 2173.05 74.09 36.42 -2950.02
Upper Platform Set B -UDCon9-1 Combination Bottom 4967.88 43.03 36.42 -2243.17
Upper Platform Set B -UDCon9-2 Combination Top 2173.07 92.5 18.39 -3531.86
Upper Platform Set B -UDCon9-2 Combination Bottom 4967.9 92.5 -12.66 -3818.51
Upper Platform Set B -UDCon9-3 Combination Top 2173.08 110.95 36.74 -3777.91
Upper Platform Set B -UDCon9-3 Combination Bottom 4967.91 142 36.74 -4484.77
Upper Platform Set B -UDCon9-4 Combination Top 2173.06 92.53 54.76 -3196.08
Upper Platform Set B -UDCon9-4 Combination Bottom 4967.89 92.53 85.82 -2909.43
Upper Platform Set B -UDCon10-1 Combination Top 1609.66 50.1 26.93 -2077.88
Upper Platform Set B -UDCon10-1 Combination Bottom 3679.91 19.05 26.93 -1371.03
Upper Platform Set B -UDCon10-2 Combination Top 1609.68 68.52 8.91 -2659.71
Upper Platform Set B -UDCon10-2 Combination Bottom 3679.93 68.52 -22.15 -2946.37
Upper Platform Set B -UDCon10-3 Combination Top 1609.69 86.96 27.25 -2905.77
Upper Platform Set B -UDCon10-3 Combination Bottom 3679.94 118.02 27.25 -3612.63
Upper Platform Set B -UDCon10-4 Combination Top 1609.67 68.55 45.28 -2323.94
Upper Platform Set B -UDCon10-4 Combination Bottom 3679.92 68.55 76.33 -2037.29
Upper Platform Set B-ENVE Combination Max Top 2633.91 149.35 68.77 -2077.88
Upper Platform Set B-ENVE Combination Max Bottom 5428.74 180.41 99.82 -1371.03
Upper Platform Set B-ENVE Combination Min Top 1609.66 50.1 8.91 -5180.96
Upper Platform Set B-ENVE Combination Min Bottom 3679.91 19.05 -22.15 -5887.82
Upper Platform Set C -UDCon1 Combination Top 1609.68 68.53 27.09 -2491.83
Upper Platform Set C -UDCon1 Combination Bottom 3679.92 68.53 27.09 -2491.83
Upper Platform Set C -UDCon2 Combination Top 2009.06 101.82 39.23 -3707.81
Upper Platform Set C -UDCon2 Combination Bottom 4079.31 101.82 39.23 -3707.81
Upper Platform Set C -UDCon3 Combination Max Top 2009.06 101.82 39.23 -3707.81
Upper Platform Set C -UDCon3 Combination Max Bottom 4079.31 101.82 39.23 -3707.81
Upper Platform Set C -UDCon3 Combination Min Top 2009.06 101.82 39.23 -3707.81
Upper Platform Set C -UDCon3 Combination Min Bottom 4079.31 101.82 39.23 -3707.81
Upper Platform Set C -UDCon4 Combination Max Top 1889.25 91.83 35.59 -3343.01
Upper Platform Set C -UDCon4 Combination Max Bottom 3959.49 91.83 35.59 -3343.02
Upper Platform Set C -UDCon4 Combination Min Top 1889.25 91.83 35.59 -3343.01
Upper Platform Set C -UDCon4 Combination Min Bottom 3959.49 91.83 35.59 -3343.02
Upper Platform Set C -UDCon5 Combination Max Top 1609.68 68.53 27.09 -2491.83
Upper Platform Set C -UDCon5 Combination Max Bottom 3679.92 68.53 27.09 -2491.83
Upper Platform Set C -UDCon5 Combination Min Top 1609.68 68.53 27.09 -2491.83
Step P VX VY T
Story Output Case Case Type Location
Type kN kN kN kN-m
Upper Platform Set C -UDCon5 Combination Min Bottom 3679.92 68.53 27.09 -2491.83
Upper Platform Set C -UDCon6-1 Combination Top 2009.05 83.39 39.07 -3293.86
Upper Platform Set C -UDCon6-1 Combination Bottom 4079.3 52.33 39.07 -2587.01
Upper Platform Set C -UDCon6-2 Combination Top 2009.07 101.8 21.05 -3875.69
Upper Platform Set C -UDCon6-2 Combination Bottom 4079.32 101.8 -10.01 -4162.35
Upper Platform Set C -UDCon6-3 Combination Top 2009.08 120.25 39.39 -4121.75
Upper Platform Set C -UDCon6-3 Combination Bottom 4079.32 151.3 39.39 -4828.61
Upper Platform Set C -UDCon6-4 Combination Top 2009.06 101.83 57.42 -3539.92
Upper Platform Set C -UDCon6-4 Combination Bottom 4079.3 101.83 88.47 -3253.27
Upper Platform Set C -UDCon7-1 Combination Top 1889.23 73.4 35.43 -2929.07
Upper Platform Set C -UDCon7-1 Combination Bottom 3959.48 42.35 35.43 -2222.21
Upper Platform Set C -UDCon7-2 Combination Top 1889.25 91.82 17.4 -3510.9
Upper Platform Set C -UDCon7-2 Combination Bottom 3959.5 91.82 -13.65 -3797.56
Upper Platform Set C -UDCon7-3 Combination Top 1889.26 110.26 35.75 -3756.96
Upper Platform Set C -UDCon7-3 Combination Bottom 3959.51 141.32 35.75 -4463.82
Upper Platform Set C -UDCon7-4 Combination Top 1889.24 91.85 53.78 -3175.13
Upper Platform Set C -UDCon7-4 Combination Bottom 3959.49 91.85 84.83 -2888.48
Upper Platform Set C -UDCon8-1 Combination Top 1609.66 50.1 26.93 -2077.88
Upper Platform Set C -UDCon8-1 Combination Bottom 3679.91 19.05 26.93 -1371.03
Upper Platform Set C -UDCon8-2 Combination Top 1609.68 68.52 8.91 -2659.71
Upper Platform Set C -UDCon8-2 Combination Bottom 3679.93 68.52 -22.15 -2946.37
Upper Platform Set C -UDCon8-3 Combination Top 1609.69 86.96 27.25 -2905.77
Upper Platform Set C -UDCon8-3 Combination Bottom 3679.94 118.02 27.25 -3612.63
Upper Platform Set C -UDCon8-4 Combination Top 1609.67 68.55 45.28 -2323.94
Upper Platform Set C -UDCon8-4 Combination Bottom 3679.92 68.55 76.33 -2037.29
Upper Platform Set C- ENVE Combination Max Top 2009.08 120.25 57.42 -2077.88
Upper Platform Set C- ENVE Combination Max Bottom 4079.32 151.3 88.47 -1371.03
Upper Platform Set C- ENVE Combination Min Top 1609.66 50.1 8.91 -4121.75
Upper Platform Set C- ENVE Combination Min Bottom 3679.91 19.05 -22.15 -4828.61
Lower Platform DL LinStatic Top 4961.33 -139.86 135.13 4324.95
Lower Platform DL LinStatic Bottom 6522.31 -139.86 135.13 4324.95
Lower Platform SDL LinStatic Top 1247.03 -67.67 54.08 2045.69
Lower Platform SDL LinStatic Bottom 1247.03 -67.67 54.08 2045.7
Lower Platform LL LinStatic Top 1491.14 -81.57 71.12 2408.85
Lower Platform LL LinStatic Bottom 1491.14 -81.57 71.12 2408.85
Lower Platform Acci Fx LinStatic Top -0.08 13.72 -3 -493.57
Lower Platform Acci Fx LinStatic Bottom -0.08 13.72 -3 -493.57
Lower Platform Acci Fy LinStatic Top -0.14 6.3 33.63 525.35
Lower Platform Acci Fy LinStatic Bottom -0.14 6.3 33.63 525.35
Lower Platform WIND LinStatic Max Top 0 0 0 0
Lower Platform WIND LinStatic Max Bottom 0 0 0 0
Lower Platform WIND LinStatic Min Top 0 0 0 0
Lower Platform WIND LinStatic Min Bottom 0 0 0 0
Lower Platform NL-0deg LinStatic Top -1.83 109.92 3.88 -1824.52
Step P VX VY T
Story Output Case Case Type Location
Type kN kN kN kN-m
Lower Platform NL-0deg LinStatic Bottom -1.83 86.5 3.88 -1295.39
Lower Platform NL-90deg LinStatic Top -0.31 18.53 142.21 1354.29
Lower Platform NL-90deg LinStatic Bottom -0.31 18.53 118.79 1136.99
Lower Platform NL-180deg LinStatic Top 1.83 -109.92 -3.88 1824.52
Lower Platform NL-180deg LinStatic Bottom 1.83 -86.5 -3.88 1295.39
Lower Platform NL-270deg LinStatic Top 0.31 -18.53 -142.21 -1354.29
Lower Platform NL-270deg LinStatic Bottom 0.31 -18.53 -118.79 -1136.99
Lower Platform Set B -UDCon1 Combination Top 8381.28 -280.16 255.43 8600.36
Lower Platform Set B -UDCon1 Combination Bottom 10488.61 -280.16 255.43 8600.38
Lower Platform SLS 1 Combination Top 7699.49 -289.1 260.33 8779.49
Lower Platform SLS 1 Combination Bottom 9260.48 -289.1 260.33 8779.5
Lower Platform ALL DL Combination Top 6208.36 -207.53 189.21 6370.64
Lower Platform ALL DL Combination Bottom 7769.34 -207.53 189.21 6370.65
Lower Platform ALL LL Combination Top 1491.14 -81.57 71.12 2408.85
Lower Platform ALL LL Combination Bottom 1491.14 -81.57 71.12 2408.85
Lower Platform ULS-A1 Combination Top 6804.74 -226.44 214.66 6840.61
Lower Platform ULS-A1 Combination Bottom 8365.72 -226.44 214.66 6840.62
Lower Platform ULS-A2 Combination Top 6804.67 -233.85 251.29 7859.53
Lower Platform ULS-A2 Combination Bottom 8365.65 -233.85 251.29 7859.54
Lower Platform DCmpD1 Combination Top 6208.36 -207.53 189.21 6370.64
Lower Platform DCmpD1 Combination Bottom 7769.34 -207.53 189.21 6370.65
Lower Platform DCmpD2 Combination Top 7699.49 -289.1 260.33 8779.49
Lower Platform DCmpD2 Combination Bottom 9260.48 -289.1 260.33 8779.5
Lower Platform DCmpS1 Combination Top 8381.28 -280.16 255.43 8600.36
Lower Platform DCmpS1 Combination Bottom 10488.61 -280.16 255.43 8600.38
Lower Platform DCmpS2 Combination Top 10617.99 -402.51 362.12 12213.64
Lower Platform DCmpS2 Combination Bottom 12725.31 -402.51 362.12 12213.65
Lower Platform DCmpC1 Combination Top 7441.99 -209.78 202.7 6487.42
Lower Platform DCmpC1 Combination Bottom 9783.47 -209.78 202.7 6487.43
Lower Platform Geo-Com1 Combination Top 10617.99 -402.51 362.12 12213.64
Lower Platform Geo-Com1 Combination Bottom 12725.31 -402.51 362.12 12213.65
Lower Platform Geo-Com2 Combination Top 8146.84 -313.57 281.67 9502.14
Lower Platform Geo-Com2 Combination Bottom 9707.82 -313.57 281.67 9502.16
Lower Platform SLS 2 Combination Max Top 7699.49 -289.1 260.33 8779.49
Lower Platform SLS 2 Combination Max Bottom 9260.48 -289.1 260.33 8779.5
Lower Platform SLS 2 Combination Min Top 7699.49 -289.1 260.33 8779.49
Lower Platform SLS 2 Combination Min Bottom 9260.48 -289.1 260.33 8779.5
Lower Platform SLS 3 Combination Max Top 7252.15 -264.63 239 8056.83
Lower Platform SLS 3 Combination Max Bottom 8813.14 -264.63 239 8056.85
Lower Platform SLS 3 Combination Min Top 7252.15 -264.63 239 8056.83
Lower Platform SLS 3 Combination Min Bottom 8813.14 -264.63 239 8056.85
Lower Platform SLS 4 Combination Max Top 6208.36 -207.53 189.21 6370.64
Lower Platform SLS 4 Combination Max Bottom 7769.34 -207.53 189.21 6370.65
Lower Platform SLS 4 Combination Min Top 6208.36 -207.53 189.21 6370.64
Step P VX VY T
Story Output Case Case Type Location
Type kN kN kN kN-m
Lower Platform SLS 4 Combination Min Bottom 7769.34 -207.53 189.21 6370.65
Lower Platform SLS ENVE Combination Max Top 7699.49 -207.53 260.33 8779.49
Lower Platform SLS ENVE Combination Max Bottom 9260.48 -207.53 260.33 8779.5
Lower Platform SLS ENVE Combination Min Top 6208.36 -289.1 189.21 6370.64
Lower Platform SLS ENVE Combination Min Bottom 7769.34 -289.1 189.21 6370.65
Lower Platform Set B -UDCon2 Combination Top 10617.99 -402.51 362.12 12213.64
Lower Platform Set B -UDCon2 Combination Bottom 12725.31 -402.51 362.12 12213.65
Lower Platform Set B -UDCon3 Combination Max Top 10617.99 -402.51 362.12 12213.64
Lower Platform Set B -UDCon3 Combination Max Bottom 12725.31 -402.51 362.12 12213.65
Lower Platform Set B -UDCon3 Combination Min Top 10617.99 -402.51 362.12 12213.64
Lower Platform Set B -UDCon3 Combination Min Bottom 12725.31 -402.51 362.12 12213.65
Lower Platform Set B -UDCon4 Combination Max Top 9946.98 -365.81 330.11 11129.65
Lower Platform Set B -UDCon4 Combination Max Bottom 12054.3 -365.81 330.11 11129.67
Lower Platform Set B -UDCon4 Combination Min Top 9946.98 -365.81 330.11 11129.65
Lower Platform Set B -UDCon4 Combination Min Bottom 12054.3 -365.81 330.11 11129.67
Lower Platform Set B -UDCon5 Combination Max Top 8381.28 -280.16 255.43 8600.36
Lower Platform Set B -UDCon5 Combination Max Bottom 10488.61 -280.16 255.43 8600.38
Lower Platform Set B -UDCon5 Combination Min Top 8381.28 -280.16 255.43 8600.36
Lower Platform Set B -UDCon5 Combination Min Bottom 10488.61 -280.16 255.43 8600.38
Lower Platform Set B -UDCon6 Combination Max Top 6208.36 -207.53 189.21 6370.64
Lower Platform Set B -UDCon6 Combination Max Bottom 7769.34 -207.53 189.21 6370.65
Lower Platform Set B -UDCon6 Combination Min Top 6208.36 -207.53 189.21 6370.64
Lower Platform Set B -UDCon6 Combination Min Bottom 7769.34 -207.53 189.21 6370.65
Lower Platform Set B -UDCon7-1 Combination Top 10616.16 -292.6 366 10389.12
Lower Platform Set B -UDCon7-1 Combination Bottom 12723.48 -316.01 366 10918.27
Lower Platform Set B -UDCon7-2 Combination Top 10617.68 -383.99 504.33 13567.93
Lower Platform Set B -UDCon7-2 Combination Bottom 12725.01 -383.99 480.91 13350.64
Lower Platform Set B -UDCon7-3 Combination Top 10619.82 -512.43 358.24 14038.15
Lower Platform Set B -UDCon7-3 Combination Bottom 12727.15 -489.02 358.24 13509.04
Lower Platform Set B -UDCon7-4 Combination Top 10618.3 -421.04 219.91 10859.34
Lower Platform Set B -UDCon7-4 Combination Bottom 12725.62 -421.04 243.33 11076.66
Lower Platform Set B -UDCon8-1 Combination Top 9945.14 -255.89 333.99 9305.14
Lower Platform Set B -UDCon8-1 Combination Bottom 12052.47 -279.31 333.99 9834.28
Lower Platform Set B -UDCon8-2 Combination Top 9946.67 -347.28 472.32 12483.95
Lower Platform Set B -UDCon8-2 Combination Bottom 12053.99 -347.28 448.91 12266.66
Lower Platform Set B -UDCon8-3 Combination Top 9948.81 -475.72 326.23 12954.17
Lower Platform Set B -UDCon8-3 Combination Bottom 12056.13 -452.31 326.23 12425.06
Lower Platform Set B -UDCon8-4 Combination Top 9947.28 -384.34 187.91 9775.36
Lower Platform Set B -UDCon8-4 Combination Bottom 12054.61 -384.34 211.32 9992.68
Lower Platform Set B -UDCon9-1 Combination Top 8379.45 -170.25 259.31 6775.85
Lower Platform Set B -UDCon9-1 Combination Bottom 10486.78 -193.66 259.31 7304.99
Lower Platform Set B -UDCon9-2 Combination Top 8380.97 -261.64 397.64 9954.66
Lower Platform Set B -UDCon9-2 Combination Bottom 10488.3 -261.64 374.23 9737.37
Lower Platform Set B -UDCon9-3 Combination Top 8383.11 -390.08 251.55 10424.88
Step P VX VY T
Story Output Case Case Type Location
Type kN kN kN kN-m
Lower Platform Set B -UDCon9-3 Combination Bottom 10490.44 -366.66 251.55 9895.76
Lower Platform Set B -UDCon9-4 Combination Top 8381.59 -298.69 113.23 7246.07
Lower Platform Set B -UDCon9-4 Combination Bottom 10488.91 -298.69 136.64 7463.39
Lower Platform Set B -UDCon10-1 Combination Top 6206.52 -97.61 193.09 4546.12
Lower Platform Set B -UDCon10-1 Combination Bottom 7767.51 -121.03 193.09 5075.26
Lower Platform Set B -UDCon10-2 Combination Top 6208.05 -189 331.42 7724.93
Lower Platform Set B -UDCon10-2 Combination Bottom 7769.03 -189 308 7507.64
Lower Platform Set B -UDCon10-3 Combination Top 6210.19 -317.44 185.33 8195.16
Lower Platform Set B -UDCon10-3 Combination Bottom 7771.17 -294.03 185.33 7666.04
Lower Platform Set B -UDCon10-4 Combination Top 6208.66 -226.05 47 5016.35
Lower Platform Set B -UDCon10-4 Combination Bottom 7769.65 -226.05 70.42 5233.66
Lower Platform Set B-ENVE Combination Max Top 10619.82 -97.61 504.33 14038.15
Lower Platform Set B-ENVE Combination Max Bottom 12727.15 -121.03 480.91 13509.04
Lower Platform Set B-ENVE Combination Min Top 6206.52 -512.43 47 4546.12
Lower Platform Set B-ENVE Combination Min Bottom 7767.51 -489.02 70.42 5075.26
Lower Platform Set C -UDCon1 Combination Top 6208.36 -207.53 189.21 6370.64
Lower Platform Set C -UDCon1 Combination Bottom 7769.34 -207.53 189.21 6370.65
Lower Platform Set C -UDCon2 Combination Top 8146.84 -313.57 281.67 9502.14
Lower Platform Set C -UDCon2 Combination Bottom 9707.82 -313.57 281.67 9502.16
Lower Platform Set C -UDCon3 Combination Max Top 8146.84 -313.57 281.67 9502.14
Lower Platform Set C -UDCon3 Combination Max Bottom 9707.82 -313.57 281.67 9502.16
Lower Platform Set C -UDCon3 Combination Min Top 8146.84 -313.57 281.67 9502.14
Lower Platform Set C -UDCon3 Combination Min Bottom 9707.82 -313.57 281.67 9502.16
Lower Platform Set C -UDCon4 Combination Max Top 7565.29 -281.75 253.93 8562.69
Lower Platform Set C -UDCon4 Combination Max Bottom 9126.27 -281.75 253.93 8562.7
Lower Platform Set C -UDCon4 Combination Min Top 7565.29 -281.75 253.93 8562.69
Lower Platform Set C -UDCon4 Combination Min Bottom 9126.27 -281.75 253.93 8562.7
Lower Platform Set C -UDCon5 Combination Max Top 6208.36 -207.53 189.21 6370.64
Lower Platform Set C -UDCon5 Combination Max Bottom 7769.34 -207.53 189.21 6370.65
Lower Platform Set C -UDCon5 Combination Min Top 6208.36 -207.53 189.21 6370.64
Lower Platform Set C -UDCon5 Combination Min Bottom 7769.34 -207.53 189.21 6370.65
Lower Platform Set C -UDCon6-1 Combination Top 8145 -203.65 285.55 7677.62
Lower Platform Set C -UDCon6-1 Combination Bottom 9705.99 -227.07 285.55 8206.77
Lower Platform Set C -UDCon6-2 Combination Top 8146.53 -295.04 423.88 10856.44
Lower Platform Set C -UDCon6-2 Combination Bottom 9707.51 -295.04 400.46 10639.15
Lower Platform Set C -UDCon6-3 Combination Top 8148.67 -423.48 277.79 11326.66
Lower Platform Set C -UDCon6-3 Combination Bottom 9709.65 -400.07 277.79 10797.54
Lower Platform Set C -UDCon6-4 Combination Top 8147.14 -332.09 139.46 8147.85
Lower Platform Set C -UDCon6-4 Combination Bottom 9708.13 -332.09 162.88 8365.17
Lower Platform Set C -UDCon7-1 Combination Top 7563.46 -171.84 257.81 6738.17
Lower Platform Set C -UDCon7-1 Combination Bottom 9124.44 -195.25 257.81 7267.32
Lower Platform Set C -UDCon7-2 Combination Top 7564.98 -263.23 396.14 9916.98
Lower Platform Set C -UDCon7-2 Combination Bottom 9125.97 -263.23 372.73 9699.69
Lower Platform Set C -UDCon7-3 Combination Top 7567.12 -391.67 250.05 10387.21
Step P VX VY T
Story Output Case Case Type Location
Type kN kN kN kN-m
Lower Platform Set C -UDCon7-3 Combination Bottom 9128.11 -368.26 250.05 9858.09
Lower Platform Set C -UDCon7-4 Combination Top 7565.6 -300.28 111.73 7208.4
Lower Platform Set C -UDCon7-4 Combination Bottom 9126.58 -300.28 135.14 7425.71
Lower Platform Set C -UDCon8-1 Combination Top 6206.52 -97.61 193.09 4546.12
Lower Platform Set C -UDCon8-1 Combination Bottom 7767.51 -121.03 193.09 5075.26
Lower Platform Set C -UDCon8-2 Combination Top 6208.05 -189 331.42 7724.93
Lower Platform Set C -UDCon8-2 Combination Bottom 7769.03 -189 308 7507.64
Lower Platform Set C -UDCon8-3 Combination Top 6210.19 -317.44 185.33 8195.16
Lower Platform Set C -UDCon8-3 Combination Bottom 7771.17 -294.03 185.33 7666.04
Lower Platform Set C -UDCon8-4 Combination Top 6208.66 -226.05 47 5016.35
Lower Platform Set C -UDCon8-4 Combination Bottom 7769.65 -226.05 70.42 5233.66
Lower Platform Set C- ENVE Combination Max Top 8148.67 -97.61 423.88 11326.66
Lower Platform Set C- ENVE Combination Max Bottom 9709.65 -121.03 400.46 10797.54
Lower Platform Set C- ENVE Combination Min Top 6206.52 -423.48 47 4546.12
Lower Platform Set C- ENVE Combination Min Bottom 7767.51 -400.07 70.42 5075.26
Staircase landing level 2 DL LinStatic Top 7353.7 -139.86 135.13 4324.95
Staircase landing level 2 DL LinStatic Bottom 8914.68 -139.86 135.13 4324.96
Staircase landing level 2 SDL LinStatic Top 1579.58 -67.67 54.08 2045.7
Staircase landing level 2 SDL LinStatic Bottom 1579.58 -67.67 54.08 2045.7
Staircase landing level 2 LL LinStatic Top 2156.25 -81.57 71.12 2408.85
Staircase landing level 2 LL LinStatic Bottom 2156.25 -81.57 71.12 2408.85
Staircase landing level 2 Acci Fx LinStatic Top -0.08 13.72 -3 -493.57
Staircase landing level 2 Acci Fx LinStatic Bottom -0.08 13.72 -3 -493.57
Staircase landing level 2 Acci Fy LinStatic Top -0.14 6.3 33.63 525.35
Staircase landing level 2 Acci Fy LinStatic Bottom -0.14 6.3 33.63 525.35
Staircase landing level 2 WIND LinStatic Max Top 0 0 0 0
Staircase landing level 2 WIND LinStatic Max Bottom 0 0 0 0
Staircase landing level 2 WIND LinStatic Min Top 0 0 0 0
Staircase landing level 2 WIND LinStatic Min Bottom 0 0 0 0
Staircase landing level 2 NL-0deg LinStatic Top -1.83 69.04 3.88 -900.58
Staircase landing level 2 NL-0deg LinStatic Bottom -1.83 45.63 3.88 -371.45
Staircase landing level 2 NL-90deg LinStatic Top -0.31 18.53 101.33 974.98
Staircase landing level 2 NL-90deg LinStatic Bottom -0.31 18.53 77.92 757.67
Staircase landing level 2 NL-180deg LinStatic Top 1.83 -69.04 -3.88 900.58
Staircase landing level 2 NL-180deg LinStatic Bottom 1.83 -45.63 -3.88 371.45
Staircase landing level 2 NL-270deg LinStatic Top 0.31 -18.53 -101.33 -974.98
Staircase landing level 2 NL-270deg LinStatic Bottom 0.31 -18.53 -77.92 -757.67
Staircase landing level 2 Set B -UDCon1 Combination Top 12059.93 -280.16 255.43 8600.38
Staircase landing level 2 Set B -UDCon1 Combination Bottom 14167.26 -280.16 255.43 8600.38
Staircase landing level 2 SLS 1 Combination Top 11089.53 -289.1 260.33 8779.5
Staircase landing level 2 SLS 1 Combination Bottom 12650.52 -289.1 260.33 8779.51
Staircase landing level 2 ALL DL Combination Top 8933.28 -207.53 189.21 6370.65
Staircase landing level 2 ALL DL Combination Bottom 10494.27 -207.53 189.21 6370.66
Staircase landing level 2 ALL LL Combination Top 2156.25 -81.57 71.12 2408.85
Step P VX VY T
Story Output Case Case Type Location
Type kN kN kN kN-m
Staircase landing level 2 ALL LL Combination Bottom 2156.25 -81.57 71.12 2408.85
Staircase landing level 2 ULS-A1 Combination Top 9795.71 -226.44 214.66 6840.62
Staircase landing level 2 ULS-A1 Combination Bottom 11356.69 -226.44 214.66 6840.63
Staircase landing level 2 ULS-A2 Combination Top 9795.64 -233.85 251.29 7859.54
Staircase landing level 2 ULS-A2 Combination Bottom 11356.62 -233.85 251.29 7859.54
Staircase landing level 2 DCmpD1 Combination Top 8933.28 -207.53 189.21 6370.65
Staircase landing level 2 DCmpD1 Combination Bottom 10494.27 -207.53 189.21 6370.66
Staircase landing level 2 DCmpD2 Combination Top 11089.53 -289.1 260.33 8779.5
Staircase landing level 2 DCmpD2 Combination Bottom 12650.52 -289.1 260.33 8779.51
Staircase landing level 2 DCmpS1 Combination Top 12059.93 -280.16 255.43 8600.38
Staircase landing level 2 DCmpS1 Combination Bottom 14167.26 -280.16 255.43 8600.38
Staircase landing level 2 DCmpS2 Combination Top 15294.31 -402.51 362.12 12213.65
Staircase landing level 2 DCmpS2 Combination Bottom 17401.64 -402.51 362.12 12213.67
Staircase landing level 2 DCmpC1 Combination Top 11030.55 -209.78 202.7 6487.43
Staircase landing level 2 DCmpC1 Combination Bottom 13372.02 -209.78 202.7 6487.43
Staircase landing level 2 Geo-Com1 Combination Top 15294.31 -402.51 362.12 12213.65
Staircase landing level 2 Geo-Com1 Combination Bottom 17401.64 -402.51 362.12 12213.67
Staircase landing level 2 Geo-Com2 Combination Top 11736.41 -313.57 281.67 9502.16
Staircase landing level 2 Geo-Com2 Combination Bottom 13297.39 -313.57 281.67 9502.17
Staircase landing level 2 SLS 2 Combination Max Top 11089.53 -289.1 260.33 8779.5
Staircase landing level 2 SLS 2 Combination Max Bottom 12650.52 -289.1 260.33 8779.51
Staircase landing level 2 SLS 2 Combination Min Top 11089.53 -289.1 260.33 8779.5
Staircase landing level 2 SLS 2 Combination Min Bottom 12650.52 -289.1 260.33 8779.51
Staircase landing level 2 SLS 3 Combination Max Top 10442.66 -264.63 239 8056.85
Staircase landing level 2 SLS 3 Combination Max Bottom 12003.64 -264.63 239 8056.85
Staircase landing level 2 SLS 3 Combination Min Top 10442.66 -264.63 239 8056.85
Staircase landing level 2 SLS 3 Combination Min Bottom 12003.64 -264.63 239 8056.85
Staircase landing level 2 SLS 4 Combination Max Top 8933.28 -207.53 189.21 6370.65
Staircase landing level 2 SLS 4 Combination Max Bottom 10494.27 -207.53 189.21 6370.66
Staircase landing level 2 SLS 4 Combination Min Top 8933.28 -207.53 189.21 6370.65
Staircase landing level 2 SLS 4 Combination Min Bottom 10494.27 -207.53 189.21 6370.66
Staircase landing level 2 SLS ENVE Combination Max Top 11089.53 -207.53 260.33 8779.5
Staircase landing level 2 SLS ENVE Combination Max Bottom 12650.52 -207.53 260.33 8779.51
Staircase landing level 2 SLS ENVE Combination Min Top 8933.28 -289.1 189.21 6370.65
Staircase landing level 2 SLS ENVE Combination Min Bottom 10494.27 -289.1 189.21 6370.66
Staircase landing level 2 Set B -UDCon2 Combination Top 15294.31 -402.51 362.12 12213.65
Staircase landing level 2 Set B -UDCon2 Combination Bottom 17401.64 -402.51 362.12 12213.67
Staircase landing level 2 Set B -UDCon3 Combination Max Top 15294.31 -402.51 362.12 12213.65
Staircase landing level 2 Set B -UDCon3 Combination Max Bottom 17401.64 -402.51 362.12 12213.67
Staircase landing level 2 Set B -UDCon3 Combination Min Top 15294.31 -402.51 362.12 12213.65
Staircase landing level 2 Set B -UDCon3 Combination Min Bottom 17401.64 -402.51 362.12 12213.67
Staircase landing level 2 Set B -UDCon4 Combination Max Top 14324 -365.81 330.11 11129.67
Staircase landing level 2 Set B -UDCon4 Combination Max Bottom 16431.32 -365.81 330.11 11129.68
Staircase landing level 2 Set B -UDCon4 Combination Min Top 14324 -365.81 330.11 11129.67
Step P VX VY T
Story Output Case Case Type Location
Type kN kN kN kN-m
Staircase landing level 2 Set B -UDCon4 Combination Min Bottom 16431.32 -365.81 330.11 11129.68
Staircase landing level 2 Set B -UDCon5 Combination Max Top 12059.93 -280.16 255.43 8600.38
Staircase landing level 2 Set B -UDCon5 Combination Max Bottom 14167.26 -280.16 255.43 8600.38
Staircase landing level 2 Set B -UDCon5 Combination Min Top 12059.93 -280.16 255.43 8600.38
Staircase landing level 2 Set B -UDCon5 Combination Min Bottom 14167.26 -280.16 255.43 8600.38
Staircase landing level 2 Set B -UDCon6 Combination Max Top 8933.28 -207.53 189.21 6370.65
Staircase landing level 2 Set B -UDCon6 Combination Max Bottom 10494.27 -207.53 189.21 6370.66
Staircase landing level 2 Set B -UDCon6 Combination Min Top 8933.28 -207.53 189.21 6370.65
Staircase landing level 2 Set B -UDCon6 Combination Min Bottom 10494.27 -207.53 189.21 6370.66
Staircase landing level 2 Set B -UDCon7-1 Combination Top 15292.48 -333.47 366 11313.08
Staircase landing level 2 Set B -UDCon7-1 Combination Bottom 17399.8 -356.89 366 11842.22
Staircase landing level 2 Set B -UDCon7-2 Combination Top 15294 -383.99 463.45 13188.64
Staircase landing level 2 Set B -UDCon7-2 Combination Bottom 17401.33 -383.99 440.04 12971.34
Staircase landing level 2 Set B -UDCon7-3 Combination Top 15296.14 -471.56 358.24 13114.23
Staircase landing level 2 Set B -UDCon7-3 Combination Bottom 17403.47 -448.14 358.24 12585.11
Staircase landing level 2 Set B -UDCon7-4 Combination Top 15294.62 -421.04 260.79 11238.67
Staircase landing level 2 Set B -UDCon7-4 Combination Bottom 17401.94 -421.04 284.2 11455.99
Staircase landing level 2 Set B -UDCon8-1 Combination Top 14322.17 -296.77 333.99 10229.09
Staircase landing level 2 Set B -UDCon8-1 Combination Bottom 16429.49 -320.18 333.99 10758.23
Staircase landing level 2 Set B -UDCon8-2 Combination Top 14323.69 -347.28 431.45 12104.65
Staircase landing level 2 Set B -UDCon8-2 Combination Bottom 16431.02 -347.28 408.03 11887.35
Staircase landing level 2 Set B -UDCon8-3 Combination Top 14325.83 -434.85 326.23 12030.25
Staircase landing level 2 Set B -UDCon8-3 Combination Bottom 16433.15 -411.44 326.23 11501.13
Staircase landing level 2 Set B -UDCon8-4 Combination Top 14324.3 -384.34 228.78 10154.69
Staircase landing level 2 Set B -UDCon8-4 Combination Bottom 16431.63 -384.34 252.19 10372.01
Staircase landing level 2 Set B -UDCon9-1 Combination Top 12058.1 -211.12 259.31 7699.8
Staircase landing level 2 Set B -UDCon9-1 Combination Bottom 14165.43 -234.54 259.31 8228.94
Staircase landing level 2 Set B -UDCon9-2 Combination Top 12059.63 -261.64 356.77 9575.36
Staircase landing level 2 Set B -UDCon9-2 Combination Bottom 14166.95 -261.64 333.35 9358.06
Staircase landing level 2 Set B -UDCon9-3 Combination Top 12061.77 -349.2 251.55 9500.95
Staircase landing level 2 Set B -UDCon9-3 Combination Bottom 14169.09 -325.79 251.55 8971.83
Staircase landing level 2 Set B -UDCon9-4 Combination Top 12060.24 -298.69 154.1 7625.39
Staircase landing level 2 Set B -UDCon9-4 Combination Bottom 14167.57 -298.69 177.51 7842.71
Staircase landing level 2 Set B -UDCon10-1 Combination Top 8931.45 -138.49 193.09 5470.07
Staircase landing level 2 Set B -UDCon10-1 Combination Bottom 10492.44 -161.9 193.09 5999.21
Staircase landing level 2 Set B -UDCon10-2 Combination Top 8932.98 -189 290.54 7345.63
Staircase landing level 2 Set B -UDCon10-2 Combination Bottom 10493.96 -189 267.13 7128.33
Staircase landing level 2 Set B -UDCon10-3 Combination Top 8935.12 -276.57 185.33 7271.23
Staircase landing level 2 Set B -UDCon10-3 Combination Bottom 10496.1 -253.15 185.33 6742.1
Staircase landing level 2 Set B -UDCon10-4 Combination Top 8933.59 -226.05 87.88 5395.67
Staircase landing level 2 Set B -UDCon10-4 Combination Bottom 10494.57 -226.05 111.29 5612.98
Staircase landing level 2 Set B-ENVE Combination Max Top 15296.14 -138.49 463.45 13188.64
Staircase landing level 2 Set B-ENVE Combination Max Bottom 17403.47 -161.9 440.04 12971.34
Staircase landing level 2 Set B-ENVE Combination Min Top 8931.45 -471.56 87.88 5395.67
Step P VX VY T
Story Output Case Case Type Location
Type kN kN kN kN-m
Staircase landing level 2 Set B-ENVE Combination Min Bottom 10492.44 -448.14 111.29 5612.98
Staircase landing level 2 Set C -UDCon1 Combination Top 8933.28 -207.53 189.21 6370.65
Staircase landing level 2 Set C -UDCon1 Combination Bottom 10494.27 -207.53 189.21 6370.66
Staircase landing level 2 Set C -UDCon2 Combination Top 11736.41 -313.57 281.67 9502.16
Staircase landing level 2 Set C -UDCon2 Combination Bottom 13297.39 -313.57 281.67 9502.17
Staircase landing level 2 Set C -UDCon3 Combination Max Top 11736.41 -313.57 281.67 9502.16
Staircase landing level 2 Set C -UDCon3 Combination Max Bottom 13297.39 -313.57 281.67 9502.17
Staircase landing level 2 Set C -UDCon3 Combination Min Top 11736.41 -313.57 281.67 9502.16
Staircase landing level 2 Set C -UDCon3 Combination Min Bottom 13297.39 -313.57 281.67 9502.17
Staircase landing level 2 Set C -UDCon4 Combination Max Top 10895.47 -281.75 253.93 8562.7
Staircase landing level 2 Set C -UDCon4 Combination Max Bottom 12456.45 -281.75 253.93 8562.71
Staircase landing level 2 Set C -UDCon4 Combination Min Top 10895.47 -281.75 253.93 8562.7
Staircase landing level 2 Set C -UDCon4 Combination Min Bottom 12456.45 -281.75 253.93 8562.71
Staircase landing level 2 Set C -UDCon5 Combination Max Top 8933.28 -207.53 189.21 6370.65
Staircase landing level 2 Set C -UDCon5 Combination Max Bottom 10494.27 -207.53 189.21 6370.66
Staircase landing level 2 Set C -UDCon5 Combination Min Top 8933.28 -207.53 189.21 6370.65
Staircase landing level 2 Set C -UDCon5 Combination Min Bottom 10494.27 -207.53 189.21 6370.66
Staircase landing level 2 Set C -UDCon6-1 Combination Top 11734.58 -244.52 285.55 8601.58
Staircase landing level 2 Set C -UDCon6-1 Combination Bottom 13295.56 -267.94 285.55 9130.72
Staircase landing level 2 Set C -UDCon6-2 Combination Top 11736.1 -295.04 383 10477.14
Staircase landing level 2 Set C -UDCon6-2 Combination Bottom 13297.08 -295.04 359.59 10259.84
Staircase landing level 2 Set C -UDCon6-3 Combination Top 11738.24 -382.61 277.79 10402.73
Staircase landing level 2 Set C -UDCon6-3 Combination Bottom 13299.22 -359.19 277.79 9873.61
Staircase landing level 2 Set C -UDCon6-4 Combination Top 11736.72 -332.09 180.34 8527.17
Staircase landing level 2 Set C -UDCon6-4 Combination Bottom 13297.7 -332.09 203.75 8744.49
Staircase landing level 2 Set C -UDCon7-1 Combination Top 10893.64 -212.71 257.81 7662.13
Staircase landing level 2 Set C -UDCon7-1 Combination Bottom 12454.62 -236.13 257.81 8191.26
Staircase landing level 2 Set C -UDCon7-2 Combination Top 10895.16 -263.23 355.27 9537.69
Staircase landing level 2 Set C -UDCon7-2 Combination Bottom 12456.15 -263.23 331.85 9320.38
Staircase landing level 2 Set C -UDCon7-3 Combination Top 10897.3 -350.8 250.05 9463.28
Staircase landing level 2 Set C -UDCon7-3 Combination Bottom 12458.29 -327.38 250.05 8934.16
Staircase landing level 2 Set C -UDCon7-4 Combination Top 10895.78 -300.28 152.6 7587.72
Staircase landing level 2 Set C -UDCon7-4 Combination Bottom 12456.76 -300.28 176.01 7805.04
Staircase landing level 2 Set C -UDCon8-1 Combination Top 8931.45 -138.49 193.09 5470.07
Staircase landing level 2 Set C -UDCon8-1 Combination Bottom 10492.44 -161.9 193.09 5999.21
Staircase landing level 2 Set C -UDCon8-2 Combination Top 8932.98 -189 290.54 7345.63
Staircase landing level 2 Set C -UDCon8-2 Combination Bottom 10493.96 -189 267.13 7128.33
Staircase landing level 2 Set C -UDCon8-3 Combination Top 8935.12 -276.57 185.33 7271.23
Staircase landing level 2 Set C -UDCon8-3 Combination Bottom 10496.1 -253.15 185.33 6742.1
Staircase landing level 2 Set C -UDCon8-4 Combination Top 8933.59 -226.05 87.88 5395.67
Staircase landing level 2 Set C -UDCon8-4 Combination Bottom 10494.57 -226.05 111.29 5612.98
Staircase landing level 2 Set C- ENVE Combination Max Top 11738.24 -138.49 383 10477.14
Staircase landing level 2 Set C- ENVE Combination Max Bottom 13299.22 -161.9 359.59 10259.84
Staircase landing level 2 Set C- ENVE Combination Min Top 8931.45 -382.61 87.88 5395.67
Step P VX VY T
Story Output Case Case Type Location
Type kN kN kN kN-m
Staircase landing level 2 Set C- ENVE Combination Min Bottom 10492.44 -359.19 111.29 5612.98
Staircase landig level 1 DL LinStatic Top 9746.07 -139.86 135.13 4324.96
Staircase landig level 1 DL LinStatic Bottom 11307.06 -139.86 135.13 4324.96
Staircase landig level 1 SDL LinStatic Top 1912.14 -67.67 54.08 2045.7
Staircase landig level 1 SDL LinStatic Bottom 1912.14 -67.67 54.08 2045.7
Staircase landig level 1 LL LinStatic Top 2821.36 -81.57 71.12 2408.85
Staircase landig level 1 LL LinStatic Bottom 2821.36 -81.57 71.12 2408.86
Staircase landig level 1 Acci Fx LinStatic Top -0.08 13.72 -3 -493.57
Staircase landig level 1 Acci Fx LinStatic Bottom -0.08 13.72 -3 -493.57
Staircase landig level 1 Acci Fy LinStatic Top -0.14 6.3 33.63 525.35
Staircase landig level 1 Acci Fy LinStatic Bottom -0.14 6.3 33.63 525.34
Staircase landig level 1 WIND LinStatic Max Top 0 0 0 0
Staircase landig level 1 WIND LinStatic Max Bottom 0 0 0 0
Staircase landig level 1 WIND LinStatic Min Top 0 0 0 0
Staircase landig level 1 WIND LinStatic Min Bottom 0 0 0 0
Staircase landig level 1 NL-0deg LinStatic Top -1.83 28.17 3.88 23.37
Staircase landig level 1 NL-0deg LinStatic Bottom -1.83 4.75 3.88 552.49
Staircase landig level 1 NL-90deg LinStatic Top -0.31 18.53 60.46 595.66
Staircase landig level 1 NL-90deg LinStatic Bottom -0.31 18.53 37.05 378.34
Staircase landig level 1 NL-180deg LinStatic Top 1.83 -28.17 -3.88 -23.37
Staircase landig level 1 NL-180deg LinStatic Bottom 1.83 -4.75 -3.88 -552.49
Staircase landig level 1 NL-270deg LinStatic Top 0.31 -18.53 -60.46 -595.66
Staircase landig level 1 NL-270deg LinStatic Bottom 0.31 -18.53 -37.05 -378.34
Staircase landig level 1 Set B -UDCon1 Combination Top 15738.59 -280.16 255.43 8600.39
Staircase landig level 1 Set B -UDCon1 Combination Bottom 17845.91 -280.16 255.43 8600.4
Staircase landig level 1 SLS 1 Combination Top 14479.58 -289.1 260.33 8779.51
Staircase landig level 1 SLS 1 Combination Bottom 16040.56 -289.1 260.33 8779.52
Staircase landig level 1 ALL DL Combination Top 11658.21 -207.53 189.21 6370.66
Staircase landig level 1 ALL DL Combination Bottom 13219.2 -207.53 189.21 6370.66
Staircase landig level 1 ALL LL Combination Top 2821.36 -81.57 71.12 2408.85
Staircase landig level 1 ALL LL Combination Bottom 2821.36 -81.57 71.12 2408.86
Staircase landig level 1 ULS-A1 Combination Top 12786.68 -226.44 214.66 6840.63
Staircase landig level 1 ULS-A1 Combination Bottom 14347.67 -226.44 214.66 6840.64
Staircase landig level 1 ULS-A2 Combination Top 12786.61 -233.85 251.29 7859.55
Staircase landig level 1 ULS-A2 Combination Bottom 14347.6 -233.85 251.29 7859.55
Staircase landig level 1 DCmpD1 Combination Top 11658.21 -207.53 189.21 6370.66
Staircase landig level 1 DCmpD1 Combination Bottom 13219.2 -207.53 189.21 6370.66
Staircase landig level 1 DCmpD2 Combination Top 14479.58 -289.1 260.33 8779.51
Staircase landig level 1 DCmpD2 Combination Bottom 16040.56 -289.1 260.33 8779.52
Staircase landig level 1 DCmpS1 Combination Top 15738.59 -280.16 255.43 8600.39
Staircase landig level 1 DCmpS1 Combination Bottom 17845.91 -280.16 255.43 8600.4
Staircase landig level 1 DCmpS2 Combination Top 19970.63 -402.51 362.12 12213.67
Staircase landig level 1 DCmpS2 Combination Bottom 22077.96 -402.51 362.12 12213.68
Staircase landig level 1 DCmpC1 Combination Top 14619.11 -209.78 202.7 6487.44
Step P VX VY T
Story Output Case Case Type Location
Type kN kN kN kN-m
Staircase landig level 1 DCmpC1 Combination Bottom 16960.58 -209.78 202.7 6487.44
Staircase landig level 1 Geo-Com1 Combination Top 19970.63 -402.51 362.12 12213.67
Staircase landig level 1 Geo-Com1 Combination Bottom 22077.96 -402.51 362.12 12213.68
Staircase landig level 1 Geo-Com2 Combination Top 15325.98 -313.57 281.67 9502.17
Staircase landig level 1 Geo-Com2 Combination Bottom 16886.97 -313.57 281.67 9502.18
Staircase landig level 1 SLS 2 Combination Max Top 14479.58 -289.1 260.33 8779.51
Staircase landig level 1 SLS 2 Combination Max Bottom 16040.56 -289.1 260.33 8779.52
Staircase landig level 1 SLS 2 Combination Min Top 14479.58 -289.1 260.33 8779.51
Staircase landig level 1 SLS 2 Combination Min Bottom 16040.56 -289.1 260.33 8779.52
Staircase landig level 1 SLS 3 Combination Max Top 13633.17 -264.63 239 8056.86
Staircase landig level 1 SLS 3 Combination Max Bottom 15194.15 -264.63 239 8056.86
Staircase landig level 1 SLS 3 Combination Min Top 13633.17 -264.63 239 8056.86
Staircase landig level 1 SLS 3 Combination Min Bottom 15194.15 -264.63 239 8056.86
Staircase landig level 1 SLS 4 Combination Max Top 11658.21 -207.53 189.21 6370.66
Staircase landig level 1 SLS 4 Combination Max Bottom 13219.2 -207.53 189.21 6370.66
Staircase landig level 1 SLS 4 Combination Min Top 11658.21 -207.53 189.21 6370.66
Staircase landig level 1 SLS 4 Combination Min Bottom 13219.2 -207.53 189.21 6370.66
Staircase landig level 1 SLS ENVE Combination Max Top 14479.58 -207.53 260.33 8779.51
Staircase landig level 1 SLS ENVE Combination Max Bottom 16040.56 -207.53 260.33 8779.52
Staircase landig level 1 SLS ENVE Combination Min Top 11658.21 -289.1 189.21 6370.66
Staircase landig level 1 SLS ENVE Combination Min Bottom 13219.2 -289.1 189.21 6370.66
Staircase landig level 1 Set B -UDCon2 Combination Top 19970.63 -402.51 362.12 12213.67
Staircase landig level 1 Set B -UDCon2 Combination Bottom 22077.96 -402.51 362.12 12213.68
Staircase landig level 1 Set B -UDCon3 Combination Max Top 19970.63 -402.51 362.12 12213.67
Staircase landig level 1 Set B -UDCon3 Combination Max Bottom 22077.96 -402.51 362.12 12213.68
Staircase landig level 1 Set B -UDCon3 Combination Min Top 19970.63 -402.51 362.12 12213.67
Staircase landig level 1 Set B -UDCon3 Combination Min Bottom 22077.96 -402.51 362.12 12213.68
Staircase landig level 1 Set B -UDCon4 Combination Max Top 18701.02 -365.81 330.11 11129.68
Staircase landig level 1 Set B -UDCon4 Combination Max Bottom 20808.34 -365.81 330.11 11129.7
Staircase landig level 1 Set B -UDCon4 Combination Min Top 18701.02 -365.81 330.11 11129.68
Staircase landig level 1 Set B -UDCon4 Combination Min Bottom 20808.34 -365.81 330.11 11129.7
Staircase landig level 1 Set B -UDCon5 Combination Max Top 15738.59 -280.16 255.43 8600.39
Staircase landig level 1 Set B -UDCon5 Combination Max Bottom 17845.91 -280.16 255.43 8600.4
Staircase landig level 1 Set B -UDCon5 Combination Min Top 15738.59 -280.16 255.43 8600.39
Staircase landig level 1 Set B -UDCon5 Combination Min Bottom 17845.91 -280.16 255.43 8600.4
Staircase landig level 1 Set B -UDCon6 Combination Max Top 11658.21 -207.53 189.21 6370.66
Staircase landig level 1 Set B -UDCon6 Combination Max Bottom 13219.2 -207.53 189.21 6370.66
Staircase landig level 1 Set B -UDCon6 Combination Min Top 11658.21 -207.53 189.21 6370.66
Staircase landig level 1 Set B -UDCon6 Combination Min Bottom 13219.2 -207.53 189.21 6370.66
Staircase landig level 1 Set B -UDCon7-1 Combination Top 19968.8 -374.35 366 12237.03
Staircase landig level 1 Set B -UDCon7-1 Combination Bottom 22076.13 -397.76 366 12766.17
Staircase landig level 1 Set B -UDCon7-2 Combination Top 19970.32 -383.99 422.58 12809.33
Staircase landig level 1 Set B -UDCon7-2 Combination Bottom 22077.65 -383.99 399.16 12592.02
Staircase landig level 1 Set B -UDCon7-3 Combination Top 19972.46 -430.68 358.24 12190.3
Step P VX VY T
Story Output Case Case Type Location
Type kN kN kN kN-m
Staircase landig level 1 Set B -UDCon7-3 Combination Bottom 22079.79 -407.27 358.24 11661.19
Staircase landig level 1 Set B -UDCon7-4 Combination Top 19970.94 -421.04 301.66 11618
Staircase landig level 1 Set B -UDCon7-4 Combination Bottom 22078.27 -421.04 325.07 11835.34
Staircase landig level 1 Set B -UDCon8-1 Combination Top 18699.19 -337.64 333.99 11153.05
Staircase landig level 1 Set B -UDCon8-1 Combination Bottom 20806.51 -361.06 333.99 11682.19
Staircase landig level 1 Set B -UDCon8-2 Combination Top 18700.71 -347.28 390.57 11725.35
Staircase landig level 1 Set B -UDCon8-2 Combination Bottom 20808.04 -347.28 367.16 11508.04
Staircase landig level 1 Set B -UDCon8-3 Combination Top 18702.85 -393.98 326.23 11106.32
Staircase landig level 1 Set B -UDCon8-3 Combination Bottom 20810.18 -370.56 326.23 10577.2
Staircase landig level 1 Set B -UDCon8-4 Combination Top 18701.33 -384.34 269.65 10534.02
Staircase landig level 1 Set B -UDCon8-4 Combination Bottom 20808.65 -384.34 293.07 10751.35
Staircase landig level 1 Set B -UDCon9-1 Combination Top 15736.76 -251.99 259.31 8623.75
Staircase landig level 1 Set B -UDCon9-1 Combination Bottom 17844.08 -275.41 259.31 9152.89
Staircase landig level 1 Set B -UDCon9-2 Combination Top 15738.28 -261.64 315.89 9196.05
Staircase landig level 1 Set B -UDCon9-2 Combination Bottom 17845.61 -261.64 292.48 8978.74
Staircase landig level 1 Set B -UDCon9-3 Combination Top 15740.42 -308.33 251.55 8577.02
Staircase landig level 1 Set B -UDCon9-3 Combination Bottom 17847.74 -284.92 251.55 8047.9
Staircase landig level 1 Set B -UDCon9-4 Combination Top 15738.9 -298.69 194.97 8004.72
Staircase landig level 1 Set B -UDCon9-4 Combination Bottom 17846.22 -298.69 218.39 8222.05
Staircase landig level 1 Set B -UDCon10-1 Combination Top 11656.38 -179.36 193.09 6394.02
Staircase landig level 1 Set B -UDCon10-1 Combination Bottom 13217.36 -202.77 193.09 6923.16
Staircase landig level 1 Set B -UDCon10-2 Combination Top 11657.9 -189 249.67 6966.32
Staircase landig level 1 Set B -UDCon10-2 Combination Bottom 13218.89 -189 226.26 6749.01
Staircase landig level 1 Set B -UDCon10-3 Combination Top 11660.04 -235.7 185.33 6347.29
Staircase landig level 1 Set B -UDCon10-3 Combination Bottom 13221.03 -212.28 185.33 5818.17
Staircase landig level 1 Set B -UDCon10-4 Combination Top 11658.52 -226.05 128.75 5774.99
Staircase landig level 1 Set B -UDCon10-4 Combination Bottom 13219.5 -226.05 152.16 5992.32
Staircase landig level 1 Set B-ENVE Combination Max Top 19972.46 -179.36 422.58 12809.33
Staircase landig level 1 Set B-ENVE Combination Max Bottom 22079.79 -189 399.16 12766.17
Staircase landig level 1 Set B-ENVE Combination Min Top 11656.38 -430.68 128.75 5774.99
Staircase landig level 1 Set B-ENVE Combination Min Bottom 13217.36 -421.04 152.16 5818.17
Staircase landig level 1 Set C -UDCon1 Combination Top 11658.21 -207.53 189.21 6370.66
Staircase landig level 1 Set C -UDCon1 Combination Bottom 13219.2 -207.53 189.21 6370.66
Staircase landig level 1 Set C -UDCon2 Combination Top 15325.98 -313.57 281.67 9502.17
Staircase landig level 1 Set C -UDCon2 Combination Bottom 16886.97 -313.57 281.67 9502.18
Staircase landig level 1 Set C -UDCon3 Combination Max Top 15325.98 -313.57 281.67 9502.17
Staircase landig level 1 Set C -UDCon3 Combination Max Bottom 16886.97 -313.57 281.67 9502.18
Staircase landig level 1 Set C -UDCon3 Combination Min Top 15325.98 -313.57 281.67 9502.17
Staircase landig level 1 Set C -UDCon3 Combination Min Bottom 16886.97 -313.57 281.67 9502.18
Staircase landig level 1 Set C -UDCon4 Combination Max Top 14225.65 -281.75 253.93 8562.71
Staircase landig level 1 Set C -UDCon4 Combination Max Bottom 15786.64 -281.75 253.93 8562.72
Staircase landig level 1 Set C -UDCon4 Combination Min Top 14225.65 -281.75 253.93 8562.71
Staircase landig level 1 Set C -UDCon4 Combination Min Bottom 15786.64 -281.75 253.93 8562.72
Staircase landig level 1 Set C -UDCon5 Combination Max Top 11658.21 -207.53 189.21 6370.66
Step P VX VY T
Story Output Case Case Type Location
Type kN kN kN kN-m
Staircase landig level 1 Set C -UDCon5 Combination Max Bottom 13219.2 -207.53 189.21 6370.66
Staircase landig level 1 Set C -UDCon5 Combination Min Top 11658.21 -207.53 189.21 6370.66
Staircase landig level 1 Set C -UDCon5 Combination Min Bottom 13219.2 -207.53 189.21 6370.66
Staircase landig level 1 Set C -UDCon6-1 Combination Top 15324.15 -285.4 285.55 9525.53
Staircase landig level 1 Set C -UDCon6-1 Combination Bottom 16885.14 -308.81 285.55 10054.67
Staircase landig level 1 Set C -UDCon6-2 Combination Top 15325.68 -295.04 342.13 10097.83
Staircase landig level 1 Set C -UDCon6-2 Combination Bottom 16886.66 -295.04 318.72 9880.52
Staircase landig level 1 Set C -UDCon6-3 Combination Top 15327.82 -341.73 277.79 9478.8
Staircase landig level 1 Set C -UDCon6-3 Combination Bottom 16888.8 -318.32 277.79 8949.68
Staircase landig level 1 Set C -UDCon6-4 Combination Top 15326.29 -332.09 221.21 8906.5
Staircase landig level 1 Set C -UDCon6-4 Combination Bottom 16887.27 -332.09 244.63 9123.83
Staircase landig level 1 Set C -UDCon7-1 Combination Top 14223.82 -253.59 257.81 8586.08
Staircase landig level 1 Set C -UDCon7-1 Combination Bottom 15784.8 -277 257.81 9115.22
Staircase landig level 1 Set C -UDCon7-2 Combination Top 14225.34 -263.23 314.39 9158.38
Staircase landig level 1 Set C -UDCon7-2 Combination Bottom 15786.33 -263.23 290.98 8941.07
Staircase landig level 1 Set C -UDCon7-3 Combination Top 14227.48 -309.92 250.05 8539.35
Staircase landig level 1 Set C -UDCon7-3 Combination Bottom 15788.47 -286.51 250.05 8010.23
Staircase landig level 1 Set C -UDCon7-4 Combination Top 14225.96 -300.28 193.47 7967.05
Staircase landig level 1 Set C -UDCon7-4 Combination Bottom 15786.94 -300.28 216.89 8184.38
Staircase landig level 1 Set C -UDCon8-1 Combination Top 11656.38 -179.36 193.09 6394.02
Staircase landig level 1 Set C -UDCon8-1 Combination Bottom 13217.36 -202.77 193.09 6923.16
Staircase landig level 1 Set C -UDCon8-2 Combination Top 11657.9 -189 249.67 6966.32
Staircase landig level 1 Set C -UDCon8-2 Combination Bottom 13218.89 -189 226.26 6749.01
Staircase landig level 1 Set C -UDCon8-3 Combination Top 11660.04 -235.7 185.33 6347.29
Staircase landig level 1 Set C -UDCon8-3 Combination Bottom 13221.03 -212.28 185.33 5818.17
Staircase landig level 1 Set C -UDCon8-4 Combination Top 11658.52 -226.05 128.75 5774.99
Staircase landig level 1 Set C -UDCon8-4 Combination Bottom 13219.5 -226.05 152.16 5992.32
Staircase landig level 1 Set C- ENVE Combination Max Top 15327.82 -179.36 342.13 10097.83
Staircase landig level 1 Set C- ENVE Combination Max Bottom 16888.8 -189 318.72 10054.67
Staircase landig level 1 Set C- ENVE Combination Min Top 11656.38 -341.73 128.75 5774.99
Staircase landig level 1 Set C- ENVE Combination Min Bottom 13217.36 -332.09 152.16 5818.17
Concourse DL LinStatic Top 14168.54 -58.2 36.14 1831.61
Concourse DL LinStatic Bottom 15279.8 -45.14 46.96 1453.59
Concourse SDL LinStatic Top 5039.04 -30.75 17.84 1058.34
Concourse SDL LinStatic Bottom 3825.81 -15.08 31.36 630.88
Concourse LL LinStatic Top 5513.8 -29.11 21.64 881.08
Concourse LL LinStatic Bottom 4667.64 -18.93 29.17 626.17
Concourse Acci Fx LinStatic Top 21.29 183 1.83 -4860.14
Concourse Acci Fx LinStatic Bottom 19.49 -1.06 1.89 60.6
Concourse Acci Fy LinStatic Top 1.26 0.37 186.44 4003.36
Concourse Acci Fy LinStatic Bottom 0.09 -0.14 -7.88 -123.48
Concourse WIND LinStatic Max Top 0 0 0 0
Concourse WIND LinStatic Max Bottom 0 0 0 0
Concourse WIND LinStatic Min Top 0 0 0 0
Step P VX VY T
Story Output Case Case Type Location
Type kN kN kN kN-m
Concourse WIND LinStatic Min Bottom 0 0 0 0
Concourse NL-0deg LinStatic Top -1.66 241.76 -1.1 -6075.16
Concourse NL-0deg LinStatic Bottom -2.12 211.88 -1.11 -5335.89
Concourse NL-90deg LinStatic Top -0.25 -1.38 211.33 1617.46
Concourse NL-90deg LinStatic Bottom 1.32 -1 177.3 1291.62
Concourse NL-180deg LinStatic Top 1.66 -241.76 1.1 6075.16
Concourse NL-180deg LinStatic Bottom 2.12 -211.88 1.11 5335.89
Concourse NL-270deg LinStatic Top 0.25 1.38 -211.33 -1617.46
Concourse NL-270deg LinStatic Bottom -1.32 1 -177.3 -1291.62
Concourse Set B -UDCon1 Combination Top 25930.24 -120.08 72.87 3901.44
Concourse Set B -UDCon1 Combination Bottom 25792.57 -81.29 105.72 2814.04
Concourse SLS 1 Combination Top 24721.38 -118.06 75.62 3771.03
Concourse SLS 1 Combination Bottom 23773.25 -79.15 107.48 2710.64
Concourse ALL DL Combination Top 19207.58 -88.95 53.98 2889.95
Concourse ALL DL Combination Bottom 19105.61 -60.21 78.31 2084.47
Concourse ALL LL Combination Top 5513.8 -29.11 21.64 881.08
Concourse ALL LL Combination Bottom 4667.64 -18.93 29.17 626.17
Concourse ULS-A1 Combination Top 21434.39 82.4 64.47 -1617.76
Concourse ULS-A1 Combination Bottom 20992.16 -68.85 91.87 2395.54
Concourse ULS-A2 Combination Top 21414.37 -100.22 249.08 7245.74
Concourse ULS-A2 Combination Bottom 20972.76 -67.93 82.1 2211.45
Concourse DCmpD1 Combination Top 19207.58 -88.95 53.98 2889.95
Concourse DCmpD1 Combination Bottom 19105.61 -60.21 78.31 2084.47
Concourse DCmpD2 Combination Top 24721.38 -118.06 75.62 3771.03
Concourse DCmpD2 Combination Bottom 23773.25 -79.15 107.48 2710.64
Concourse DCmpS1 Combination Top 25930.24 -120.08 72.87 3901.44
Concourse DCmpS1 Combination Bottom 25792.57 -81.29 105.72 2814.04
Concourse DCmpS2 Combination Top 34200.94 -163.75 105.33 5223.06
Concourse DCmpS2 Combination Bottom 32794.03 -109.69 149.47 3753.28
Concourse DCmpC1 Combination Top 21252.82 -87.3 54.21 2747.42
Concourse DCmpC1 Combination Bottom 22919.7 -67.7 70.44 2180.39
Concourse Geo-Com1 Combination Top 34200.94 -163.75 105.33 5223.06
Concourse Geo-Com1 Combination Bottom 32794.03 -109.69 149.47 3753.28
Concourse Geo-Com2 Combination Top 26375.53 -126.8 82.11 4035.36
Concourse Geo-Com2 Combination Bottom 25173.54 -84.83 116.23 2898.49
Concourse SLS 2 Combination Max Top 24721.38 -118.06 75.62 3771.03
Concourse SLS 2 Combination Max Bottom 23773.25 -79.15 107.48 2710.64
Concourse SLS 2 Combination Min Top 24721.38 -118.06 75.62 3771.03
Concourse SLS 2 Combination Min Bottom 23773.25 -79.15 107.48 2710.64
Concourse SLS 3 Combination Max Top 23067.24 -109.33 69.13 3506.71
Concourse SLS 3 Combination Max Bottom 22372.95 -73.47 98.73 2522.79
Concourse SLS 3 Combination Min Top 23067.24 -109.33 69.13 3506.71
Concourse SLS 3 Combination Min Bottom 22372.95 -73.47 98.73 2522.79
Concourse SLS 4 Combination Max Top 19207.58 -88.95 53.98 2889.95
Step P VX VY T
Story Output Case Case Type Location
Type kN kN kN kN-m
Concourse SLS 4 Combination Max Bottom 19105.61 -60.21 78.31 2084.47
Concourse SLS 4 Combination Min Top 19207.58 -88.95 53.98 2889.95
Concourse SLS 4 Combination Min Bottom 19105.61 -60.21 78.31 2084.47
Concourse SLS ENVE Combination Max Top 24721.38 -88.95 75.62 3771.03
Concourse SLS ENVE Combination Max Bottom 23773.25 -60.21 107.48 2710.64
Concourse SLS ENVE Combination Min Top 19207.58 -118.06 53.98 2889.95
Concourse SLS ENVE Combination Min Bottom 19105.61 -79.15 78.31 2084.47
Concourse Set B -UDCon2 Combination Top 34200.94 -163.75 105.33 5223.06
Concourse Set B -UDCon2 Combination Bottom 32794.03 -109.69 149.47 3753.28
Concourse Set B -UDCon3 Combination Max Top 34200.94 -163.75 105.33 5223.06
Concourse Set B -UDCon3 Combination Max Bottom 32794.03 -109.69 149.47 3753.28
Concourse Set B -UDCon3 Combination Min Top 34200.94 -163.75 105.33 5223.06
Concourse Set B -UDCon3 Combination Min Bottom 32794.03 -109.69 149.47 3753.28
Concourse Set B -UDCon4 Combination Max Top 31719.73 -150.65 95.59 4826.57
Concourse Set B -UDCon4 Combination Max Bottom 30693.59 -101.17 136.35 3471.51
Concourse Set B -UDCon4 Combination Min Top 31719.73 -150.65 95.59 4826.57
Concourse Set B -UDCon4 Combination Min Bottom 30693.59 -101.17 136.35 3471.51
Concourse Set B -UDCon5 Combination Max Top 25930.24 -120.08 72.87 3901.44
Concourse Set B -UDCon5 Combination Max Bottom 25792.57 -81.29 105.72 2814.04
Concourse Set B -UDCon5 Combination Min Top 25930.24 -120.08 72.87 3901.44
Concourse Set B -UDCon5 Combination Min Bottom 25792.57 -81.29 105.72 2814.04
Concourse Set B -UDCon6 Combination Max Top 19207.58 -88.95 53.98 2889.95
Concourse Set B -UDCon6 Combination Max Bottom 19105.61 -60.21 78.31 2084.47
Concourse Set B -UDCon6 Combination Min Top 19207.58 -88.95 53.98 2889.95
Concourse Set B -UDCon6 Combination Min Bottom 19105.61 -60.21 78.31 2084.47
Concourse Set B -UDCon7-1 Combination Top 34199.28 78 104.23 -852.1
Concourse Set B -UDCon7-1 Combination Bottom 32791.9 102.19 148.36 -1582.6
Concourse Set B -UDCon7-2 Combination Top 34200.69 -165.13 316.66 6840.52
Concourse Set B -UDCon7-2 Combination Bottom 32795.35 -110.69 326.77 5044.9
Concourse Set B -UDCon7-3 Combination Top 34202.6 -405.51 106.43 11298.21
Concourse Set B -UDCon7-3 Combination Bottom 32796.15 -321.57 150.59 9089.17
Concourse Set B -UDCon7-4 Combination Top 34201.19 -162.37 -106 3605.6
Concourse Set B -UDCon7-4 Combination Bottom 32792.71 -108.69 -27.82 2461.67
Concourse Set B -UDCon8-1 Combination Top 31718.07 91.1 94.49 -1248.58
Concourse Set B -UDCon8-1 Combination Bottom 30691.47 110.71 135.24 -1864.38
Concourse Set B -UDCon8-2 Combination Top 31719.48 -152.03 306.92 6444.03
Concourse Set B -UDCon8-2 Combination Bottom 30694.91 -102.17 313.64 4763.13
Concourse Set B -UDCon8-3 Combination Top 31721.39 -392.41 96.69 10901.73
Concourse Set B -UDCon8-3 Combination Bottom 30695.71 -313.05 137.46 8807.4
Concourse Set B -UDCon8-4 Combination Top 31719.98 -149.27 -115.73 3209.11
Concourse Set B -UDCon8-4 Combination Bottom 30692.27 -100.17 -40.95 2179.89
Concourse Set B -UDCon9-1 Combination Top 25928.57 121.67 71.77 -2173.72
Concourse Set B -UDCon9-1 Combination Bottom 25790.45 130.59 104.61 -2521.85
Concourse Set B -UDCon9-2 Combination Top 25929.98 -121.46 284.2 5518.9
Step P VX VY T
Story Output Case Case Type Location
Type kN kN kN kN-m
Concourse Set B -UDCon9-2 Combination Bottom 25793.89 -82.29 283.02 4105.65
Concourse Set B -UDCon9-3 Combination Top 25931.9 -361.84 73.97 9976.59
Concourse Set B -UDCon9-3 Combination Bottom 25794.7 -293.17 106.83 8149.92
Concourse Set B -UDCon9-4 Combination Top 25930.49 -118.7 -138.45 2283.98
Concourse Set B -UDCon9-4 Combination Bottom 25791.25 -80.29 -71.57 1522.42
Concourse Set B -UDCon10-1 Combination Top 19205.92 152.81 52.88 -3185.2
Concourse Set B -UDCon10-1 Combination Bottom 19103.48 151.67 77.2 -3251.42
Concourse Set B -UDCon10-2 Combination Top 19207.33 -90.33 265.31 4507.41
Concourse Set B -UDCon10-2 Combination Bottom 19106.93 -61.21 255.61 3376.09
Concourse Set B -UDCon10-3 Combination Top 19209.24 -330.7 55.08 8965.11
Concourse Set B -UDCon10-3 Combination Bottom 19107.73 -272.1 79.43 7420.36
Concourse Set B -UDCon10-4 Combination Top 19207.83 -87.57 -157.35 1272.49
Concourse Set B -UDCon10-4 Combination Bottom 19104.29 -59.21 -98.98 792.85
Concourse Set B-ENVE Combination Max Top 34202.6 152.81 316.66 11298.21
Concourse Set B-ENVE Combination Max Bottom 32796.15 151.67 326.77 9089.17
Concourse Set B-ENVE Combination Min Top 19205.92 -405.51 -157.35 -3185.2
Concourse Set B-ENVE Combination Min Bottom 19103.48 -321.57 -98.98 -3251.42
Concourse Set C -UDCon1 Combination Top 19207.58 -88.95 53.98 2889.95
Concourse Set C -UDCon1 Combination Bottom 19105.61 -60.21 78.31 2084.47
Concourse Set C -UDCon2 Combination Top 26375.53 -126.8 82.11 4035.36
Concourse Set C -UDCon2 Combination Bottom 25173.54 -84.83 116.23 2898.49
Concourse Set C -UDCon3 Combination Max Top 26375.53 -126.8 82.11 4035.36
Concourse Set C -UDCon3 Combination Max Bottom 25173.54 -84.83 116.23 2898.49
Concourse Set C -UDCon3 Combination Min Top 26375.53 -126.8 82.11 4035.36
Concourse Set C -UDCon3 Combination Min Bottom 25173.54 -84.83 116.23 2898.49
Concourse Set C -UDCon4 Combination Max Top 24225.14 -115.44 73.67 3691.74
Concourse Set C -UDCon4 Combination Max Bottom 23353.16 -77.44 104.86 2654.28
Concourse Set C -UDCon4 Combination Min Top 24225.14 -115.44 73.67 3691.74
Concourse Set C -UDCon4 Combination Min Bottom 23353.16 -77.44 104.86 2654.28
Concourse Set C -UDCon5 Combination Max Top 19207.58 -88.95 53.98 2889.95
Concourse Set C -UDCon5 Combination Max Bottom 19105.61 -60.21 78.31 2084.47
Concourse Set C -UDCon5 Combination Min Top 19207.58 -88.95 53.98 2889.95
Concourse Set C -UDCon5 Combination Min Bottom 19105.61 -60.21 78.31 2084.47
Concourse Set C -UDCon6-1 Combination Top 26373.86 114.96 81.01 -2039.8
Concourse Set C -UDCon6-1 Combination Bottom 25171.41 127.05 115.12 -2437.4
Concourse Set C -UDCon6-2 Combination Top 26375.28 -128.18 293.44 5652.82
Concourse Set C -UDCon6-2 Combination Bottom 25174.86 -85.83 293.53 4190.1
Concourse Set C -UDCon6-3 Combination Top 26377.19 -368.55 83.21 10110.51
Concourse Set C -UDCon6-3 Combination Bottom 25175.66 -296.71 117.34 8234.37
Concourse Set C -UDCon6-4 Combination Top 26375.78 -125.42 -129.22 2417.9
Concourse Set C -UDCon6-4 Combination Bottom 25172.22 -83.83 -61.06 1606.87
Concourse Set C -UDCon7-1 Combination Top 24223.48 126.31 72.57 -2383.42
Concourse Set C -UDCon7-1 Combination Bottom 23351.03 134.44 103.74 -2681.61
Concourse Set C -UDCon7-2 Combination Top 24224.89 -116.83 285 5309.2
Step P VX VY T
Story Output Case Case Type Location
Type kN kN kN kN-m
Concourse Set C -UDCon7-2 Combination Bottom 23354.48 -78.44 282.15 3945.9
Concourse Set C -UDCon7-3 Combination Top 24226.81 -357.2 74.77 9766.89
Concourse Set C -UDCon7-3 Combination Bottom 23355.28 -289.33 105.97 7990.17
Concourse Set C -UDCon7-4 Combination Top 24225.39 -114.06 -137.66 2074.28
Concourse Set C -UDCon7-4 Combination Bottom 23351.84 -76.44 -72.44 1362.66
Concourse Set C -UDCon8-1 Combination Top 19205.92 152.81 52.88 -3185.2
Concourse Set C -UDCon8-1 Combination Bottom 19103.48 151.67 77.2 -3251.42
Concourse Set C -UDCon8-2 Combination Top 19207.33 -90.33 265.31 4507.41
Concourse Set C -UDCon8-2 Combination Bottom 19106.93 -61.21 255.61 3376.09
Concourse Set C -UDCon8-3 Combination Top 19209.24 -330.7 55.08 8965.11
Concourse Set C -UDCon8-3 Combination Bottom 19107.73 -272.1 79.43 7420.36
Concourse Set C -UDCon8-4 Combination Top 19207.83 -87.57 -157.35 1272.49
Concourse Set C -UDCon8-4 Combination Bottom 19104.29 -59.21 -98.98 792.85
Concourse Set C- ENVE Combination Max Top 26377.19 152.81 293.44 10110.51
Concourse Set C- ENVE Combination Max Bottom 25175.66 151.67 293.53 8234.37
Concourse Set C- ENVE Combination Min Top 19205.92 -368.55 -157.35 -3185.2
Concourse Set C- ENVE Combination Min Bottom 19103.48 -296.71 -98.98 -3251.42
Ground- walkway Rf DL LinStatic Top 15605.82 -46.7 28.08 1502.1
Ground- walkway Rf DL LinStatic Bottom 17585.77 -46.7 28.08 1502.09
Ground- walkway Rf SDL LinStatic Top 3839.45 -15.77 17.43 632.94
Ground- walkway Rf SDL LinStatic Bottom 3839.45 -15.77 17.43 632.94
Ground- walkway Rf LL LinStatic Top 4987.8 -20.8 16.18 672.28
Ground- walkway Rf LL LinStatic Bottom 4987.8 -20.8 16.18 672.27
Ground- walkway Rf Acci Fx LinStatic Top 19.83 -1 1.88 58.78
Ground- walkway Rf Acci Fx LinStatic Bottom 19.83 -1 1.88 58.78
Ground- walkway Rf Acci Fy LinStatic Top 0.12 -0.14 -7.8 -123.37
Ground- walkway Rf Acci Fy LinStatic Bottom 0.12 -0.14 -7.8 -123.37
Ground- walkway Rf WIND LinStatic Max Top 0 0 0 0
Ground- walkway Rf WIND LinStatic Max Bottom 0 0 0 0
Ground- walkway Rf WIND LinStatic Min Top 0 0 0 0
Ground- walkway Rf WIND LinStatic Min Bottom 0 0 0 0
Ground- walkway Rf NL-0deg LinStatic Top -2.38 194.75 -1.09 -4949.59
Ground- walkway Rf NL-0deg LinStatic Bottom -2.38 165.05 -1.09 -4278.44
Ground- walkway Rf NL-90deg LinStatic Top 1.51 -1.03 160.55 1130.17
Ground- walkway Rf NL-90deg LinStatic Bottom 1.51 -1.03 130.85 854.55
Ground- walkway Rf NL-180deg LinStatic Top 2.38 -194.75 1.09 4949.59
Ground- walkway Rf NL-180deg LinStatic Bottom 2.38 -165.05 1.09 4278.44
Ground- walkway Rf NL-270deg LinStatic Top -1.51 1.03 -160.55 -1130.17
Ground- walkway Rf NL-270deg LinStatic Bottom -1.51 1.03 -130.85 -854.55
Ground- walkway Rf Set B -UDCon1 Combination Top 26251.11 -84.33 61.45 2882.31
Ground- walkway Rf Set B -UDCon1 Combination Bottom 28924.04 -84.33 61.45 2882.29
Ground- walkway Rf SLS 1 Combination Top 24433.06 -83.27 61.7 2807.32
Ground- walkway Rf SLS 1 Combination Bottom 26413.01 -83.27 61.7 2807.3
Ground- walkway Rf ALL DL Combination Top 19445.27 -62.46 45.52 2135.05
Step P VX VY T
Story Output Case Case Type Location
Type kN kN kN kN-m
Ground- walkway Rf ALL DL Combination Bottom 21425.22 -62.46 45.52 2135.03
Ground- walkway Rf ALL LL Combination Top 4987.8 -20.8 16.18 672.28
Ground- walkway Rf ALL LL Combination Bottom 4987.8 -20.8 16.18 672.27
Ground- walkway Rf ULS-A1 Combination Top 21460.21 -71.78 53.87 2462.74
Ground- walkway Rf ULS-A1 Combination Bottom 23440.16 -71.78 53.87 2462.72
Ground- walkway Rf ULS-A2 Combination Top 21440.51 -70.92 44.19 2280.59
Ground- walkway Rf ULS-A2 Combination Bottom 23420.45 -70.92 44.19 2280.57
Ground- walkway Rf DCmpD1 Combination Top 19445.27 -62.46 45.52 2135.05
Ground- walkway Rf DCmpD1 Combination Bottom 21425.22 -62.46 45.52 2135.03
Ground- walkway Rf DCmpD2 Combination Top 24433.06 -83.27 61.7 2807.32
Ground- walkway Rf DCmpD2 Combination Bottom 26413.01 -83.27 61.7 2807.3
Ground- walkway Rf DCmpS1 Combination Top 26251.11 -84.33 61.45 2882.31
Ground- walkway Rf DCmpS1 Combination Bottom 28924.04 -84.33 61.45 2882.29
Ground- walkway Rf DCmpS2 Combination Top 33732.81 -115.53 85.72 3890.73
Ground- walkway Rf DCmpS2 Combination Bottom 36405.74 -115.53 85.72 3890.7
Ground- walkway Rf DCmpC1 Combination Top 23408.73 -70.05 42.12 2253.15
Ground- walkway Rf DCmpC1 Combination Bottom 26378.65 -70.05 42.12 2253.14
Ground- walkway Rf Geo-Com1 Combination Top 33732.81 -115.53 85.72 3890.73
Ground- walkway Rf Geo-Com1 Combination Bottom 36405.74 -115.53 85.72 3890.7
Ground- walkway Rf Geo-Com2 Combination Top 25929.4 -89.51 66.56 3009.01
Ground- walkway Rf Geo-Com2 Combination Bottom 27909.35 -89.51 66.56 3008.98
Ground- walkway Rf SLS 2 Combination Max Top 24433.06 -83.27 61.7 2807.32
Ground- walkway Rf SLS 2 Combination Max Bottom 26413.01 -83.27 61.7 2807.3
Ground- walkway Rf SLS 2 Combination Min Top 24433.06 -83.27 61.7 2807.32
Ground- walkway Rf SLS 2 Combination Min Bottom 26413.01 -83.27 61.7 2807.3
Ground- walkway Rf SLS 3 Combination Max Top 22936.73 -77.03 56.84 2605.64
Ground- walkway Rf SLS 3 Combination Max Bottom 24916.67 -77.03 56.84 2605.62
Ground- walkway Rf SLS 3 Combination Min Top 22936.73 -77.03 56.84 2605.64
Ground- walkway Rf SLS 3 Combination Min Bottom 24916.67 -77.03 56.84 2605.62
Ground- walkway Rf SLS 4 Combination Max Top 19445.27 -62.46 45.52 2135.05
Ground- walkway Rf SLS 4 Combination Max Bottom 21425.22 -62.46 45.52 2135.03
Ground- walkway Rf SLS 4 Combination Min Top 19445.27 -62.46 45.52 2135.05
Ground- walkway Rf SLS 4 Combination Min Bottom 21425.22 -62.46 45.52 2135.03
Ground- walkway Rf SLS ENVE Combination Max Top 24433.06 -62.46 61.7 2807.32
Ground- walkway Rf SLS ENVE Combination Max Bottom 26413.01 -62.46 61.7 2807.3
Ground- walkway Rf SLS ENVE Combination Min Top 19445.27 -83.27 45.52 2135.05
Ground- walkway Rf SLS ENVE Combination Min Bottom 21425.22 -83.27 45.52 2135.03
Ground- walkway Rf Set B -UDCon2 Combination Top 33732.81 -115.53 85.72 3890.73
Ground- walkway Rf Set B -UDCon2 Combination Bottom 36405.74 -115.53 85.72 3890.7
Ground- walkway Rf Set B -UDCon3 Combination Max Top 33732.81 -115.53 85.72 3890.73
Ground- walkway Rf Set B -UDCon3 Combination Max Bottom 36405.74 -115.53 85.72 3890.7
Ground- walkway Rf Set B -UDCon3 Combination Min Top 33732.81 -115.53 85.72 3890.73
Ground- walkway Rf Set B -UDCon3 Combination Min Bottom 36405.74 -115.53 85.72 3890.7
Ground- walkway Rf Set B -UDCon4 Combination Max Top 31488.3 -106.17 78.44 3588.2
Step P VX VY T
Story Output Case Case Type Location
Type kN kN kN kN-m
Ground- walkway Rf Set B -UDCon4 Combination Max Bottom 34161.23 -106.17 78.44 3588.18
Ground- walkway Rf Set B -UDCon4 Combination Min Top 31488.3 -106.17 78.44 3588.2
Ground- walkway Rf Set B -UDCon4 Combination Min Bottom 34161.23 -106.17 78.44 3588.18
Ground- walkway Rf Set B -UDCon5 Combination Max Top 26251.11 -84.33 61.45 2882.31
Ground- walkway Rf Set B -UDCon5 Combination Max Bottom 28924.04 -84.33 61.45 2882.29
Ground- walkway Rf Set B -UDCon5 Combination Min Top 26251.11 -84.33 61.45 2882.31
Ground- walkway Rf Set B -UDCon5 Combination Min Bottom 28924.04 -84.33 61.45 2882.29
Ground- walkway Rf Set B -UDCon6 Combination Max Top 19445.27 -62.46 45.52 2135.05
Ground- walkway Rf Set B -UDCon6 Combination Max Bottom 21425.22 -62.46 45.52 2135.03
Ground- walkway Rf Set B -UDCon6 Combination Min Top 19445.27 -62.46 45.52 2135.05
Ground- walkway Rf Set B -UDCon6 Combination Min Bottom 21425.22 -62.46 45.52 2135.03
Ground- walkway Rf Set B -UDCon7-1 Combination Top 33730.42 79.22 84.63 -1058.86
Ground- walkway Rf Set B -UDCon7-1 Combination Bottom 36403.35 49.52 84.63 -387.74
Ground- walkway Rf Set B -UDCon7-2 Combination Top 33734.32 -116.56 246.28 5020.89
Ground- walkway Rf Set B -UDCon7-2 Combination Bottom 36407.25 -116.56 216.58 4745.25
Ground- walkway Rf Set B -UDCon7-3 Combination Top 33735.19 -310.28 86.81 8840.32
Ground- walkway Rf Set B -UDCon7-3 Combination Bottom 36408.12 -280.58 86.81 8169.14
Ground- walkway Rf Set B -UDCon7-4 Combination Top 33731.29 -114.5 -74.83 2760.56
Ground- walkway Rf Set B -UDCon7-4 Combination Bottom 36404.22 -114.5 -45.13 3036.14
Ground- walkway Rf Set B -UDCon8-1 Combination Top 31485.92 88.58 77.35 -1361.39
Ground- walkway Rf Set B -UDCon8-1 Combination Bottom 34158.84 58.88 77.35 -690.26
Ground- walkway Rf Set B -UDCon8-2 Combination Top 31489.81 -107.2 238.99 4718.37
Ground- walkway Rf Set B -UDCon8-2 Combination Bottom 34162.74 -107.2 209.29 4442.73
Ground- walkway Rf Set B -UDCon8-3 Combination Top 31490.68 -300.92 79.53 8537.79
Ground- walkway Rf Set B -UDCon8-3 Combination Bottom 34163.61 -271.22 79.53 7866.62
Ground- walkway Rf Set B -UDCon8-4 Combination Top 31486.78 -105.14 -82.11 2458.04
Ground- walkway Rf Set B -UDCon8-4 Combination Bottom 34159.71 -105.14 -52.41 2733.62
Ground- walkway Rf Set B -UDCon9-1 Combination Top 26248.73 110.42 60.35 -2067.28
Ground- walkway Rf Set B -UDCon9-1 Combination Bottom 28921.66 80.72 60.35 -1396.15
Ground- walkway Rf Set B -UDCon9-2 Combination Top 26252.63 -85.35 222 4012.48
Ground- walkway Rf Set B -UDCon9-2 Combination Bottom 28925.56 -85.35 192.3 3736.85
Ground- walkway Rf Set B -UDCon9-3 Combination Top 26253.5 -279.07 62.54 7831.9
Ground- walkway Rf Set B -UDCon9-3 Combination Bottom 28926.43 -249.38 62.54 7160.73
Ground- walkway Rf Set B -UDCon9-4 Combination Top 26249.6 -83.3 -99.11 1752.15
Ground- walkway Rf Set B -UDCon9-4 Combination Bottom 28922.53 -83.3 -69.41 2027.74
Ground- walkway Rf Set B -UDCon10-1 Combination Top 19442.89 132.28 44.42 -2814.54
Ground- walkway Rf Set B -UDCon10-1 Combination Bottom 21422.83 102.59 44.42 -2143.41
Ground- walkway Rf Set B -UDCon10-2 Combination Top 19446.78 -63.49 206.07 3265.21
Ground- walkway Rf Set B -UDCon10-2 Combination Bottom 21426.73 -63.49 176.37 2989.59
Ground- walkway Rf Set B -UDCon10-3 Combination Top 19447.65 -257.21 46.61 7084.64
Ground- walkway Rf Set B -UDCon10-3 Combination Bottom 21427.6 -227.51 46.61 6413.47
Ground- walkway Rf Set B -UDCon10-4 Combination Top 19443.75 -61.43 -115.04 1004.88
Ground- walkway Rf Set B -UDCon10-4 Combination Bottom 21423.7 -61.43 -85.34 1280.48
Ground- walkway Rf Set B-ENVE Combination Max Top 33735.19 132.28 246.28 8840.32
Step P VX VY T
Story Output Case Case Type Location
Type kN kN kN kN-m
Ground- walkway Rf Set B-ENVE Combination Max Bottom 36408.12 102.59 216.58 8169.14
Ground- walkway Rf Set B-ENVE Combination Min Top 19442.89 -310.28 -115.04 -2814.54
Ground- walkway Rf Set B-ENVE Combination Min Bottom 21422.83 -280.58 -85.34 -2143.41
Ground- walkway Rf Set C -UDCon1 Combination Top 19445.27 -62.46 45.52 2135.05
Ground- walkway Rf Set C -UDCon1 Combination Bottom 21425.22 -62.46 45.52 2135.03
Ground- walkway Rf Set C -UDCon2 Combination Top 25929.4 -89.51 66.56 3009.01
Ground- walkway Rf Set C -UDCon2 Combination Bottom 27909.35 -89.51 66.56 3008.98
Ground- walkway Rf Set C -UDCon3 Combination Max Top 25929.4 -89.51 66.56 3009.01
Ground- walkway Rf Set C -UDCon3 Combination Max Bottom 27909.35 -89.51 66.56 3008.98
Ground- walkway Rf Set C -UDCon3 Combination Min Top 25929.4 -89.51 66.56 3009.01
Ground- walkway Rf Set C -UDCon3 Combination Min Bottom 27909.35 -89.51 66.56 3008.98
Ground- walkway Rf Set C -UDCon4 Combination Max Top 23984.16 -81.39 60.24 2746.82
Ground- walkway Rf Set C -UDCon4 Combination Max Bottom 25964.11 -81.39 60.24 2746.8
Ground- walkway Rf Set C -UDCon4 Combination Min Top 23984.16 -81.39 60.24 2746.82
Ground- walkway Rf Set C -UDCon4 Combination Min Bottom 25964.11 -81.39 60.24 2746.8
Ground- walkway Rf Set C -UDCon5 Combination Max Top 19445.27 -62.46 45.52 2135.05
Ground- walkway Rf Set C -UDCon5 Combination Max Bottom 21425.22 -62.46 45.52 2135.03
Ground- walkway Rf Set C -UDCon5 Combination Min Top 19445.27 -62.46 45.52 2135.05
Ground- walkway Rf Set C -UDCon5 Combination Min Bottom 21425.22 -62.46 45.52 2135.03
Ground- walkway Rf Set C -UDCon6-1 Combination Top 25927.02 105.24 65.46 -1940.58
Ground- walkway Rf Set C -UDCon6-1 Combination Bottom 27906.97 75.54 65.46 -1269.46
Ground- walkway Rf Set C -UDCon6-2 Combination Top 25930.92 -90.54 227.11 4139.17
Ground- walkway Rf Set C -UDCon6-2 Combination Bottom 27910.87 -90.54 197.41 3863.54
Ground- walkway Rf Set C -UDCon6-3 Combination Top 25931.79 -284.26 67.65 7958.6
Ground- walkway Rf Set C -UDCon6-3 Combination Bottom 27911.73 -254.56 67.65 7287.42
Ground- walkway Rf Set C -UDCon6-4 Combination Top 25927.89 -88.48 -94 1878.84
Ground- walkway Rf Set C -UDCon6-4 Combination Bottom 27907.84 -88.48 -64.3 2154.43
Ground- walkway Rf Set C -UDCon7-1 Combination Top 23981.78 113.35 59.15 -2202.77
Ground- walkway Rf Set C -UDCon7-1 Combination Bottom 25961.73 83.66 59.15 -1531.64
Ground- walkway Rf Set C -UDCon7-2 Combination Top 23985.68 -82.42 220.8 3876.98
Ground- walkway Rf Set C -UDCon7-2 Combination Bottom 25965.62 -82.42 191.1 3601.35
Ground- walkway Rf Set C -UDCon7-3 Combination Top 23986.55 -276.14 61.34 7696.41
Ground- walkway Rf Set C -UDCon7-3 Combination Bottom 25966.49 -246.44 61.34 7025.24
Ground- walkway Rf Set C -UDCon7-4 Combination Top 23982.65 -80.36 -100.31 1616.65
Ground- walkway Rf Set C -UDCon7-4 Combination Bottom 25962.6 -80.36 -70.61 1892.24
Ground- walkway Rf Set C -UDCon8-1 Combination Top 19442.89 132.28 44.42 -2814.54
Ground- walkway Rf Set C -UDCon8-1 Combination Bottom 21422.83 102.59 44.42 -2143.41
Ground- walkway Rf Set C -UDCon8-2 Combination Top 19446.78 -63.49 206.07 3265.21
Ground- walkway Rf Set C -UDCon8-2 Combination Bottom 21426.73 -63.49 176.37 2989.59
Ground- walkway Rf Set C -UDCon8-3 Combination Top 19447.65 -257.21 46.61 7084.64
Ground- walkway Rf Set C -UDCon8-3 Combination Bottom 21427.6 -227.51 46.61 6413.47
Ground- walkway Rf Set C -UDCon8-4 Combination Top 19443.75 -61.43 -115.04 1004.88
Ground- walkway Rf Set C -UDCon8-4 Combination Bottom 21423.7 -61.43 -85.34 1280.48
Ground- walkway Rf Set C- ENVE Combination Max Top 25931.79 132.28 227.11 7958.6
Step P VX VY T
Story Output Case Case Type Location
Type kN kN kN kN-m
Ground- walkway Rf Set C- ENVE Combination Max Bottom 27911.73 102.59 197.41 7287.42
Ground- walkway Rf Set C- ENVE Combination Min Top 19442.89 -284.26 -115.04 -2814.54
Ground- walkway Rf Set C- ENVE Combination Min Bottom 21422.83 -254.56 -85.34 -2143.41
Ground DL LinStatic Top 27616.55 -52.38 22.52 1740.66
Ground DL LinStatic Bottom 28081.75 -52.38 22.52 1740.66
Ground SDL LinStatic Top 6293.21 -22.23 11.84 892.98
Ground SDL LinStatic Bottom 6293.21 -22.23 11.84 892.98
Ground LL LinStatic Top 8167.43 -23.84 13.44 795.29
Ground LL LinStatic Bottom 8167.43 -23.84 13.44 795.29
Ground Acci Fx LinStatic Top 20.86 -0.85 1.81 52.81
Ground Acci Fx LinStatic Bottom 20.86 -0.85 1.81 52.81
Ground Acci Fy LinStatic Top -0.08 -0.29 -7.66 -114.78
Ground Acci Fy LinStatic Bottom -0.08 -0.29 -7.66 -114.78
Ground WIND LinStatic Max Top 0 0 0 0
Ground WIND LinStatic Max Bottom 0 0 0 0
Ground WIND LinStatic Min Top 0 0 0 0
Ground WIND LinStatic Min Bottom 0 0 0 0
Ground NL-0deg LinStatic Top -1.96 -15.77 -1.08 318.31
Ground NL-0deg LinStatic Bottom -1.96 -22.75 -1.08 483.67
Ground NL-90deg LinStatic Top -0.22 -1.42 -45.6 -510.38
Ground NL-90deg LinStatic Bottom -0.22 -1.42 -52.58 -572.01
Ground NL-180deg LinStatic Top 1.96 15.77 1.08 -318.31
Ground NL-180deg LinStatic Bottom 1.96 22.75 1.08 -483.67
Ground NL-270deg LinStatic Top 0.22 1.42 45.6 510.38
Ground NL-270deg LinStatic Bottom 0.22 1.42 52.58 572.01
Ground Set B -UDCon1 Combination Top 45778.17 -100.72 46.38 3555.41
Ground Set B -UDCon1 Combination Bottom 46406.19 -100.72 46.38 3555.41
Ground SLS 1 Combination Top 42077.19 -98.45 47.8 3428.93
Ground SLS 1 Combination Bottom 42542.39 -98.45 47.8 3428.93
Ground ALL DL Combination Top 33909.76 -74.61 34.36 2633.64
Ground ALL DL Combination Bottom 34374.96 -74.61 34.36 2633.64
Ground ALL LL Combination Top 8167.43 -23.84 13.44 795.29
Ground ALL LL Combination Bottom 8167.43 -23.84 13.44 795.29
Ground ULS-A1 Combination Top 37197.59 -84.99 41.55 3004.57
Ground ULS-A1 Combination Bottom 37662.79 -84.99 41.55 3004.57
Ground ULS-A2 Combination Top 37176.65 -84.43 32.07 2836.98
Ground ULS-A2 Combination Bottom 37641.85 -84.43 32.07 2836.98
Ground DCmpD1 Combination Top 33909.76 -74.61 34.36 2633.64
Ground DCmpD1 Combination Bottom 34374.96 -74.61 34.36 2633.64
Ground DCmpD2 Combination Top 42077.19 -98.45 47.8 3428.93
Ground DCmpD2 Combination Bottom 42542.39 -98.45 47.8 3428.93
Ground DCmpS1 Combination Top 45778.17 -100.72 46.38 3555.41
Ground DCmpS1 Combination Bottom 46406.19 -100.72 46.38 3555.41
Ground DCmpS2 Combination Top 58029.32 -136.48 66.55 4748.35
Step P VX VY T
Story Output Case Case Type Location
Type kN kN kN kN-m
Ground DCmpS2 Combination Bottom 58657.34 -136.48 66.55 4748.35
Ground DCmpC1 Combination Top 41424.82 -78.57 33.77 2610.99
Ground DCmpC1 Combination Bottom 42122.62 -78.57 33.77 2610.99
Ground Geo-Com1 Combination Top 58029.32 -136.48 66.55 4748.35
Ground Geo-Com1 Combination Bottom 58657.34 -136.48 66.55 4748.35
Ground Geo-Com2 Combination Top 44527.42 -105.6 51.83 3667.52
Ground Geo-Com2 Combination Bottom 44992.62 -105.6 51.83 3667.52
Ground SLS 2 Combination Max Top 42077.19 -98.45 47.8 3428.93
Ground SLS 2 Combination Max Bottom 42542.39 -98.45 47.8 3428.93
Ground SLS 2 Combination Min Top 42077.19 -98.45 47.8 3428.93
Ground SLS 2 Combination Min Bottom 42542.39 -98.45 47.8 3428.93
Ground SLS 3 Combination Max Top 39626.96 -91.3 43.77 3190.34
Ground SLS 3 Combination Max Bottom 40092.16 -91.3 43.77 3190.34
Ground SLS 3 Combination Min Top 39626.96 -91.3 43.77 3190.34
Ground SLS 3 Combination Min Bottom 40092.16 -91.3 43.77 3190.34
Ground SLS 4 Combination Max Top 33909.76 -74.61 34.36 2633.64
Ground SLS 4 Combination Max Bottom 34374.96 -74.61 34.36 2633.64
Ground SLS 4 Combination Min Top 33909.76 -74.61 34.36 2633.64
Ground SLS 4 Combination Min Bottom 34374.96 -74.61 34.36 2633.64
Ground SLS ENVE Combination Max Top 42077.19 -74.61 47.8 3428.93
Ground SLS ENVE Combination Max Bottom 42542.39 -74.61 47.8 3428.93
Ground SLS ENVE Combination Min Top 33909.76 -98.45 34.36 2633.64
Ground SLS ENVE Combination Min Bottom 34374.96 -98.45 34.36 2633.64
Ground Set B -UDCon2 Combination Top 58029.32 -136.48 66.55 4748.35
Ground Set B -UDCon2 Combination Bottom 58657.34 -136.48 66.55 4748.35
Ground Set B -UDCon3 Combination Max Top 58029.32 -136.48 66.55 4748.35
Ground Set B -UDCon3 Combination Max Bottom 58657.34 -136.48 66.55 4748.35
Ground Set B -UDCon3 Combination Min Top 58029.32 -136.48 66.55 4748.35
Ground Set B -UDCon3 Combination Min Bottom 58657.34 -136.48 66.55 4748.35
Ground Set B -UDCon4 Combination Max Top 54353.97 -125.75 60.5 4390.47
Ground Set B -UDCon4 Combination Max Bottom 54981.99 -125.75 60.5 4390.47
Ground Set B -UDCon4 Combination Min Top 54353.97 -125.75 60.5 4390.47
Ground Set B -UDCon4 Combination Min Bottom 54981.99 -125.75 60.5 4390.47
Ground Set B -UDCon5 Combination Max Top 45778.17 -100.72 46.38 3555.41
Ground Set B -UDCon5 Combination Max Bottom 46406.19 -100.72 46.38 3555.41
Ground Set B -UDCon5 Combination Min Top 45778.17 -100.72 46.38 3555.41
Ground Set B -UDCon5 Combination Min Bottom 46406.19 -100.72 46.38 3555.41
Ground Set B -UDCon6 Combination Max Top 33909.76 -74.61 34.36 2633.64
Ground Set B -UDCon6 Combination Max Bottom 34374.96 -74.61 34.36 2633.64
Ground Set B -UDCon6 Combination Min Top 33909.76 -74.61 34.36 2633.64
Ground Set B -UDCon6 Combination Min Bottom 34374.96 -74.61 34.36 2633.64
Ground Set B -UDCon7-1 Combination Top 58027.35 -152.25 65.46 5066.65
Ground Set B -UDCon7-1 Combination Bottom 58655.37 -159.23 65.46 5232.02
Ground Set B -UDCon7-2 Combination Top 58029.09 -137.9 20.95 4237.97
Step P VX VY T
Story Output Case Case Type Location
Type kN kN kN kN-m
Ground Set B -UDCon7-2 Combination Bottom 58657.11 -137.9 13.97 4176.34
Ground Set B -UDCon7-3 Combination Top 58031.28 -120.71 67.63 4430.04
Ground Set B -UDCon7-3 Combination Bottom 58659.3 -113.74 67.63 4264.68
Ground Set B -UDCon7-4 Combination Top 58029.54 -135.06 112.15 5258.73
Ground Set B -UDCon7-4 Combination Bottom 58657.56 -135.06 119.12 5320.36
Ground Set B -UDCon8-1 Combination Top 54352.01 -141.52 59.41 4708.77
Ground Set B -UDCon8-1 Combination Bottom 54980.03 -148.5 59.41 4874.14
Ground Set B -UDCon8-2 Combination Top 54353.75 -127.17 14.9 3880.09
Ground Set B -UDCon8-2 Combination Bottom 54981.77 -127.17 7.92 3818.46
Ground Set B -UDCon8-3 Combination Top 54355.94 -109.99 61.58 4072.16
Ground Set B -UDCon8-3 Combination Bottom 54983.96 -103.01 61.58 3906.8
Ground Set B -UDCon8-4 Combination Top 54354.2 -124.34 106.1 4900.85
Ground Set B -UDCon8-4 Combination Bottom 54982.22 -124.34 113.07 4962.48
Ground Set B -UDCon9-1 Combination Top 45776.21 -116.49 45.3 3873.72
Ground Set B -UDCon9-1 Combination Bottom 46404.23 -123.47 45.3 4039.08
Ground Set B -UDCon9-2 Combination Top 45777.95 -102.14 0.78 3045.03
Ground Set B -UDCon9-2 Combination Bottom 46405.97 -102.14 -6.2 2983.4
Ground Set B -UDCon9-3 Combination Top 45780.13 -84.96 47.46 3237.11
Ground Set B -UDCon9-3 Combination Bottom 46408.16 -77.98 47.46 3071.75
Ground Set B -UDCon9-4 Combination Top 45778.4 -99.31 91.98 4065.79
Ground Set B -UDCon9-4 Combination Bottom 46406.42 -99.31 98.96 4127.42
Ground Set B -UDCon10-1 Combination Top 33907.79 -90.38 33.27 2951.95
Ground Set B -UDCon10-1 Combination Bottom 34372.99 -97.36 33.27 3117.31
Ground Set B -UDCon10-2 Combination Top 33909.53 -76.03 -11.24 2123.26
Ground Set B -UDCon10-2 Combination Bottom 34374.73 -76.03 -18.22 2061.63
Ground Set B -UDCon10-3 Combination Top 33911.72 -58.84 35.44 2315.33
Ground Set B -UDCon10-3 Combination Bottom 34376.92 -51.86 35.44 2149.97
Ground Set B -UDCon10-4 Combination Top 33909.98 -73.19 79.96 3144.02
Ground Set B -UDCon10-4 Combination Bottom 34375.18 -73.19 86.93 3205.65
Ground Set B-ENVE Combination Max Top 58031.28 -58.84 112.15 5258.73
Ground Set B-ENVE Combination Max Bottom 58659.3 -51.86 119.12 5320.36
Ground Set B-ENVE Combination Min Top 33907.79 -152.25 -11.24 2123.26
Ground Set B-ENVE Combination Min Bottom 34372.99 -159.23 -18.22 2061.63
Ground Set C -UDCon1 Combination Top 33909.76 -74.61 34.36 2633.64
Ground Set C -UDCon1 Combination Bottom 34374.96 -74.61 34.36 2633.64
Ground Set C -UDCon2 Combination Top 44527.42 -105.6 51.83 3667.52
Ground Set C -UDCon2 Combination Bottom 44992.62 -105.6 51.83 3667.52
Ground Set C -UDCon3 Combination Max Top 44527.42 -105.6 51.83 3667.52
Ground Set C -UDCon3 Combination Max Bottom 44992.62 -105.6 51.83 3667.52
Ground Set C -UDCon3 Combination Min Top 44527.42 -105.6 51.83 3667.52
Ground Set C -UDCon3 Combination Min Bottom 44992.62 -105.6 51.83 3667.52
Ground Set C -UDCon4 Combination Max Top 41342.12 -96.3 46.59 3357.35
Ground Set C -UDCon4 Combination Max Bottom 41807.32 -96.3 46.59 3357.35
Ground Set C -UDCon4 Combination Min Top 41342.12 -96.3 46.59 3357.35
Step P VX VY T
Story Output Case Case Type Location
Type kN kN kN kN-m
Ground Set C -UDCon4 Combination Min Bottom 41807.32 -96.3 46.59 3357.35
Ground Set C -UDCon5 Combination Max Top 33909.76 -74.61 34.36 2633.64
Ground Set C -UDCon5 Combination Max Bottom 34374.96 -74.61 34.36 2633.64
Ground Set C -UDCon5 Combination Min Top 33909.76 -74.61 34.36 2633.64
Ground Set C -UDCon5 Combination Min Bottom 34374.96 -74.61 34.36 2633.64
Ground Set C -UDCon6-1 Combination Top 44525.45 -121.37 50.75 3985.82
Ground Set C -UDCon6-1 Combination Bottom 44990.65 -128.35 50.75 4151.18
Ground Set C -UDCon6-2 Combination Top 44527.19 -107.02 6.23 3157.14
Ground Set C -UDCon6-2 Combination Bottom 44992.39 -107.02 -0.74 3095.51
Ground Set C -UDCon6-3 Combination Top 44529.38 -89.83 52.92 3349.21
Ground Set C -UDCon6-3 Combination Bottom 44994.58 -82.85 52.92 3183.85
Ground Set C -UDCon6-4 Combination Top 44527.64 -104.18 97.43 4177.9
Ground Set C -UDCon6-4 Combination Bottom 44992.84 -104.18 104.41 4239.53
Ground Set C -UDCon7-1 Combination Top 41340.15 -112.07 45.51 3675.66
Ground Set C -UDCon7-1 Combination Bottom 41805.36 -119.05 45.51 3841.02
Ground Set C -UDCon7-2 Combination Top 41341.89 -97.72 0.99 2846.97
Ground Set C -UDCon7-2 Combination Bottom 41807.09 -97.72 -5.99 2785.34
Ground Set C -UDCon7-3 Combination Top 41344.08 -80.54 47.67 3039.05
Ground Set C -UDCon7-3 Combination Bottom 41809.28 -73.56 47.67 2873.69
Ground Set C -UDCon7-4 Combination Top 41342.34 -94.89 92.19 3867.73
Ground Set C -UDCon7-4 Combination Bottom 41807.54 -94.89 99.17 3929.36
Ground Set C -UDCon8-1 Combination Top 33907.79 -90.38 33.27 2951.95
Ground Set C -UDCon8-1 Combination Bottom 34372.99 -97.36 33.27 3117.31
Ground Set C -UDCon8-2 Combination Top 33909.53 -76.03 -11.24 2123.26
Ground Set C -UDCon8-2 Combination Bottom 34374.73 -76.03 -18.22 2061.63
Ground Set C -UDCon8-3 Combination Top 33911.72 -58.84 35.44 2315.33
Ground Set C -UDCon8-3 Combination Bottom 34376.92 -51.86 35.44 2149.97
Ground Set C -UDCon8-4 Combination Top 33909.98 -73.19 79.96 3144.02
Ground Set C -UDCon8-4 Combination Bottom 34375.18 -73.19 86.93 3205.65
Ground Set C- ENVE Combination Max Top 44529.38 -58.84 97.43 4177.9
Ground Set C- ENVE Combination Max Bottom 44994.58 -51.86 104.41 4239.53
Ground Set C- ENVE Combination Min Top 33907.79 -121.37 -11.24 2123.26
Ground Set C- ENVE Combination Min Bottom 34372.99 -128.35 -18.22 2061.63
MX MY
kN-m kN-m
29639.61 -9193.48
76706.8 -28176.17
11729.64 -4289.26
11704.57 -4207.71
7730.06 -2621.17
7701.82 -2543.53
-0.06 -0.01
0.13 0.18
MX MY
kN-m kN-m
0.15 0.02
-0.64 -0.03
0 0
0 0
0 0
0 0
-0.54 -0.07
-0.05 -102.93
0.47 0.03
102.54 -0.01
0.54 0.07
0.05 102.93
-0.47 -0.03
-102.54 0.01
55848.49 -18201.7
119355.35 -43718.24
49099.3 -16103.91
96113.19 -34927.41
41369.25 -13482.74
88411.37 -32383.88
7730.06 -2621.17
7701.82 -2543.53
44461.21 -14531.22
91492.23 -33401.11
44461.42 -14531.19
91491.46 -33401.32
41369.25 -13482.74
88411.37 -32383.88
49099.3 -16103.91
96113.19 -34927.41
55848.49 -18201.7
119355.35 -43718.24
67443.57 -22133.46
130908.08 -47533.54
44459.41 -13790.22
115060.19 -42264.25
67443.57 -22133.46
130908.08 -47533.54
51418.32 -16890.27
98423.74 -35690.47
49099.3 -16103.91
96113.19 -34927.41
49099.3 -16103.91
96113.19 -34927.41
46780.29 -15317.56
MX MY
kN-m kN-m
93802.65 -34164.35
46780.29 -15317.56
93802.65 -34164.35
41369.25 -13482.74
88411.37 -32383.88
41369.25 -13482.74
88411.37 -32383.88
49099.3 -13482.74
96113.19 -32383.88
41369.25 -16103.91
88411.37 -34927.41
67443.57 -22133.46
130908.08 -47533.54
67443.57 -22133.46
130908.08 -47533.54
67443.57 -22133.46
130908.08 -47533.54
63965.04 -20953.93
127442.26 -46388.95
63965.04 -20953.93
127442.26 -46388.95
55848.49 -18201.7
119355.35 -43718.24
55848.49 -18201.7
119355.35 -43718.24
41369.25 -13482.74
88411.37 -32383.88
41369.25 -13482.74
88411.37 -32383.88
67443.03 -22133.53
130908.03 -47636.46
67444.04 -22133.43
131010.63 -47533.54
67444.11 -22133.38
130908.14 -47430.61
67443.1 -22133.49
130805.54 -47533.53
63964.5 -20954.01
127442.21 -46491.87
63965.52 -20953.9
127544.81 -46388.96
63965.58 -20953.86
127442.32 -46286.02
63964.57 -20953.96
127339.72 -46388.94
MX MY
kN-m kN-m
55847.95 -18201.77
119355.29 -43821.16
55848.96 -18201.66
119457.89 -43718.25
55849.02 -18201.62
119355.4 -43615.31
55848.01 -18201.73
119252.81 -43718.23
41368.71 -13482.81
88411.31 -32486.81
41369.72 -13482.71
88513.91 -32383.89
41369.79 -13482.66
88411.42 -32280.95
41368.78 -13482.77
88308.83 -32383.87
67444.11 -13482.66
131010.63 -32280.95
41368.71 -22133.53
88308.83 -47636.46
41369.25 -13482.74
88411.37 -32383.88
51418.32 -16890.27
98423.74 -35690.47
51418.32 -16890.27
98423.74 -35690.47
51418.32 -16890.27
98423.74 -35690.47
48403.6 -15868.01
95420.03 -34698.49
48403.6 -15868.01
95420.03 -34698.49
41369.25 -13482.74
88411.37 -32383.88
41369.25 -13482.74
88411.37 -32383.88
51417.78 -16890.34
98423.68 -35793.4
51418.79 -16890.23
98526.28 -35690.48
51418.86 -16890.19
98423.79 -35587.55
51417.85 -16890.3
98321.2 -35690.46
48403.06 -15868.08
MX MY
kN-m kN-m
95419.97 -34801.42
48404.07 -15867.97
95522.57 -34698.5
48404.14 -15867.93
95420.08 -34595.57
48403.13 -15868.04
95317.49 -34698.49
41368.71 -13482.81
88411.31 -32486.81
41369.72 -13482.71
88513.91 -32383.89
41369.79 -13482.66
88411.42 -32280.95
41368.78 -13482.77
88308.83 -32383.87
51418.86 -13482.66
98526.28 -32280.95
41368.71 -16890.34
88308.83 -35793.4
119170.06 -42614.92
154133.64 -57423.7
30831.14 -10504.14
30706.32 -10660.37
38479.81 -12377.06
38315.64 -12565.38
-2.98 0.52
3.95 32.21
2.58 0.59
-75.14 15.15
0 0
0 0
0 0
0 0
-27.52 -95.17
-36.49 131.77
122.91 1.14
-178.8 43.95
27.52 95.17
36.49 -131.77
-122.91 -1.14
178.8 -43.95
202501.62 -71710.73
249533.95 -91913.5
188481 -65496.12
223155.61 -80649.45
MX MY
kN-m kN-m
150001.2 -53119.06
184839.96 -68084.07
38479.81 -12377.06
38315.64 -12565.38
165390.14 -58069.36
200170.18 -73078.01
165395.7 -58069.29
200091.08 -73095.07
150001.2 -53119.06
184839.96 -68084.07
188481 -65496.12
223155.61 -80649.45
202501.62 -71710.73
249533.95 -91913.5
260221.33 -90276.32
307007.42 -110761.57
178755.08 -63922.38
231200.47 -86135.55
260221.33 -90276.32
307007.42 -110761.57
200024.95 -69209.24
234650.3 -84419.07
188481 -65496.12
223155.61 -80649.45
188481 -65496.12
223155.61 -80649.45
176937.06 -61783
211660.92 -76879.84
176937.06 -61783
211660.92 -76879.84
150001.2 -53119.06
184839.96 -68084.07
150001.2 -53119.06
184839.96 -68084.07
188481 -53119.06
223155.61 -68084.07
150001.2 -65496.12
184839.96 -80649.45
260221.33 -90276.32
307007.42 -110761.57
260221.33 -90276.32
307007.42 -110761.57
260221.33 -90276.32
307007.42 -110761.57
242905.41 -84706.64
MX MY
kN-m kN-m
289765.38 -105107.14
242905.41 -84706.64
289765.38 -105107.14
202501.62 -71710.73
249533.95 -91913.5
202501.62 -71710.73
249533.95 -91913.5
150001.2 -53119.06
184839.96 -68084.07
150001.2 -53119.06
184839.96 -68084.07
260193.8 -90371.49
306970.93 -110629.79
260344.24 -90275.18
306828.62 -110717.61
260248.85 -90181.15
307043.91 -110893.34
260098.41 -90277.47
307186.22 -110805.52
242877.89 -84801.81
289728.89 -104975.37
243028.33 -84705.5
289586.58 -105063.19
242932.94 -84611.47
289801.87 -105238.92
242782.5 -84707.79
289944.18 -105151.1
202474.1 -71805.9
249497.46 -91781.72
202624.53 -71709.58
249355.15 -91869.54
202529.14 -71615.55
249570.44 -92045.27
202378.7 -71711.87
249712.75 -91957.45
149973.68 -53214.23
184803.47 -67952.3
150124.11 -53117.91
184661.17 -68040.12
150028.72 -53023.88
184876.46 -68215.85
149878.28 -53120.2
185018.76 -68128.02
260344.24 -53023.88
307186.22 -67952.3
MX MY
kN-m kN-m
149878.28 -90371.49
184661.17 -110893.34
150001.2 -53119.06
184839.96 -68084.07
200024.95 -69209.24
234650.3 -84419.07
200024.95 -69209.24
234650.3 -84419.07
200024.95 -69209.24
234650.3 -84419.07
185017.82 -64382.18
219707.2 -79518.57
185017.82 -64382.18
219707.2 -79518.57
150001.2 -53119.06
184839.96 -68084.07
150001.2 -53119.06
184839.96 -68084.07
199997.42 -69304.41
234613.81 -84287.29
200147.86 -69208.1
234471.51 -84375.11
200052.47 -69114.07
234686.79 -84550.84
199902.03 -69210.38
234829.1 -84463.02
184990.3 -64477.36
219670.71 -79386.79
185140.73 -64381.04
219528.4 -79474.61
185045.34 -64287.01
219743.69 -79650.34
184894.91 -64383.33
219886 -79562.52
149973.68 -53214.23
184803.47 -67952.3
150124.11 -53117.91
184661.17 -68040.12
150028.72 -53023.88
184876.46 -68215.85
149878.28 -53120.2
185018.76 -68128.02
200147.86 -53023.88
234829.1 -67952.3
149878.28 -69304.41
MX MY
kN-m kN-m
184661.17 -84550.84
172934.14 -65139.02
207897.79 -79947.75
38226.52 -13746.5
38101.72 -13902.69
53356.04 -18737.63
53191.91 -18925.89
3.95 32.21
10.89 63.9
-75.14 15.15
-152.88 29.71
0 0
0 0
0 0
0 0
-36.49 131.77
-45.46 264.32
-178.79 43.95
-386.17 86.77
36.49 -131.77
45.46 -264.32
178.79 -43.95
386.17 -86.77
285066.89 -106495.45
332099.34 -126698.09
264516.7 -97623.15
299191.42 -112776.33
211160.66 -78885.52
245999.51 -93850.44
53356.04 -18737.63
53191.91 -18925.89
232507.03 -86348.36
267287.17 -101356.89
232427.93 -86365.42
267123.4 -101391.08
211160.66 -78885.52
245999.51 -93850.44
264516.7 -97623.15
299191.42 -112776.33
285066.89 -106495.45
332099.34 -126698.09
365100.95 -134601.89
411887.2 -155086.93
259401.21 -97708.53
311846.69 -119921.62
MX MY
kN-m kN-m
365100.95 -134601.89
411887.2 -155086.93
280523.51 -103244.44
315148.99 -118454.1
264516.7 -97623.15
299191.42 -112776.33
264516.7 -97623.15
299191.42 -112776.33
248509.89 -92001.86
283233.85 -107098.56
248509.89 -92001.86
283233.85 -107098.56
211160.66 -78885.52
245999.51 -93850.44
211160.66 -78885.52
245999.51 -93850.44
264516.7 -78885.52
299191.42 -93850.44
211160.66 -97623.15
245999.51 -112776.33
365100.95 -134601.89
411887.2 -155086.93
365100.95 -134601.89
411887.2 -155086.93
365100.95 -134601.89
411887.2 -155086.93
341090.73 -126169.96
387950.85 -146570.28
341090.73 -126169.96
387950.85 -146570.28
285066.89 -106495.45
332099.34 -126698.09
285066.89 -106495.45
332099.34 -126698.09
211160.66 -78885.52
245999.51 -93850.44
211160.66 -78885.52
245999.51 -93850.44
365064.46 -134470.12
411841.74 -154822.61
364922.16 -134557.94
411501.04 -155000.17
365137.44 -134733.66
411932.67 -155351.25
365279.74 -134645.84
MX MY
kN-m kN-m
412273.37 -155173.7
341054.24 -126038.19
387905.39 -146305.96
340911.94 -126126.01
387564.68 -146483.52
341127.22 -126301.73
387996.31 -146834.6
341269.52 -126213.91
388337.01 -146657.05
285030.4 -106363.68
332053.88 -126433.77
284888.09 -106451.5
331713.18 -126611.33
285103.38 -106627.22
332144.8 -126962.41
285245.68 -106539.4
332485.51 -126784.86
211124.17 -78753.75
245954.05 -93586.12
210981.86 -78841.56
245613.35 -93763.67
211197.15 -79017.28
246044.97 -94114.76
211339.45 -78929.47
246385.68 -93937.2
365279.74 -78753.75
412273.37 -93586.12
210981.86 -134733.66
245613.35 -155351.25
211160.66 -78885.52
245999.51 -93850.44
280523.51 -103244.44
315148.99 -118454.1
280523.51 -103244.44
315148.99 -118454.1
280523.51 -103244.44
315148.99 -118454.1
259714.65 -95936.76
294404.15 -111073
259714.65 -95936.76
294404.15 -111073
211160.66 -78885.52
245999.51 -93850.44
211160.66 -78885.52
245999.51 -93850.44
MX MY
kN-m kN-m
280487.02 -103112.67
315103.53 -118189.78
280344.72 -103200.48
314762.83 -118367.34
280560 -103376.2
315194.45 -118718.42
280702.3 -103288.39
315535.16 -118540.87
259678.16 -95804.99
294358.69 -110808.68
259535.86 -95892.81
294017.98 -110986.24
259751.15 -96068.53
294449.61 -111337.32
259893.45 -95980.71
294790.31 -111159.77
211124.17 -78753.75
245954.05 -93586.12
210981.86 -78841.56
245613.35 -93763.67
211197.15 -79017.28
246044.97 -94114.76
211339.45 -78929.47
246385.68 -93937.2
280702.3 -78753.75
315535.16 -93586.12
210981.86 -103376.2
245613.35 -118718.42
226698.28 -87663.07
261662.01 -102471.71
45621.92 -16988.82
45497.16 -17144.98
68232.3 -25098.14
68068.21 -25286.37
10.89 63.9
17.83 95.59
-152.88 29.71
-230.62 44.27
0 0
0 0
0 0
0 0
-45.46 264.31
-54.43 302.48
-386.16 86.76
MX MY
kN-m kN-m
-499.17 129.58
45.46 -264.31
54.43 -302.48
386.16 -86.76
499.17 -129.58
367632.27 -141280.04
414664.88 -161482.53
340552.5 -129750.03
375227.38 -144903.06
272320.2 -104651.88
307159.17 -119616.69
68232.3 -25098.14
68068.21 -25286.37
299624.01 -114627.24
334404.29 -129635.65
299460.24 -114661.43
334155.83 -129686.96
272320.2 -104651.88
307159.17 -119616.69
340552.5 -129750.03
375227.38 -144903.06
367632.27 -141280.04
414664.88 -161482.53
469980.72 -178927.26
516767.2 -199412.08
340047.42 -131494.6
392493.02 -153707.57
469980.72 -178927.26
516767.2 -199412.08
361022.19 -137279.47
395647.85 -152488.97
340552.5 -129750.03
375227.38 -144903.06
340552.5 -129750.03
375227.38 -144903.06
320082.81 -122220.58
354806.92 -137317.15
320082.81 -122220.58
354806.92 -137317.15
272320.2 -104651.88
307159.17 -119616.69
272320.2 -104651.88
307159.17 -119616.69
340552.5 -104651.88
375227.38 -119616.69
MX MY
kN-m kN-m
272320.2 -129750.03
307159.17 -144903.06
469980.72 -178927.26
516767.2 -199412.08
469980.72 -178927.26
516767.2 -199412.08
469980.72 -178927.26
516767.2 -199412.08
439276.19 -167633.09
486136.51 -188033.22
439276.19 -167633.09
486136.51 -188033.22
367632.27 -141280.04
414664.88 -161482.53
367632.27 -141280.04
414664.88 -161482.53
272320.2 -104651.88
307159.17 -119616.69
272320.2 -104651.88
307159.17 -119616.69
469935.26 -178662.94
516712.77 -199109.61
469594.56 -178840.49
516268.03 -199282.5
470026.18 -179191.57
516821.63 -199714.56
470366.88 -179014.02
517266.37 -199541.67
439230.73 -167368.78
486082.07 -187730.74
438890.03 -167546.33
485637.34 -187903.64
439321.65 -167897.41
486190.94 -188335.69
439662.35 -167719.86
486635.67 -188162.8
367586.81 -141015.73
414610.45 -161180.06
367246.11 -141193.28
414165.72 -161352.95
367677.73 -141544.36
414719.32 -161785.01
368018.43 -141366.81
415164.05 -161612.11
272274.74 -104387.57
MX MY
kN-m kN-m
307104.74 -119314.22
271934.04 -104565.12
306660.01 -119487.11
272365.66 -104916.2
307213.61 -119919.17
272706.36 -104738.65
307658.34 -119746.27
470366.88 -104387.57
517266.37 -119314.22
271934.04 -179191.57
306660.01 -199714.56
272320.2 -104651.88
307159.17 -119616.69
361022.19 -137279.47
395647.85 -152488.97
361022.19 -137279.47
395647.85 -152488.97
361022.19 -137279.47
395647.85 -152488.97
334411.59 -127491.19
369101.25 -142627.29
334411.59 -127491.19
369101.25 -142627.29
272320.2 -104651.88
307159.17 -119616.69
272320.2 -104651.88
307159.17 -119616.69
360976.73 -137015.16
395593.42 -152186.49
360636.03 -137192.71
395148.68 -152359.39
361067.65 -137543.78
395702.28 -152791.44
361408.35 -137366.23
396147.02 -152618.55
334366.13 -127226.88
369046.81 -142324.81
334025.44 -127404.43
368602.08 -142497.71
334457.06 -127755.51
369155.68 -142929.76
334797.75 -127577.96
369600.41 -142756.87
272274.74 -104387.57
307104.74 -119314.22
MX MY
kN-m kN-m
271934.04 -104565.12
306660.01 -119487.11
272365.66 -104916.2
307213.61 -119919.17
272706.36 -104738.65
307658.34 -119746.27
361408.35 -104387.57
396147.02 -119314.22
271934.04 -137543.78
306660.01 -152791.44
334727.12 -121495.3
357086.02 -135480.47
123937.46 -38583.66
93479 -31606.37
136322.96 -44843.65
114636.95 -39380.8
588.63 -435.66
533.7 -180.86
-192.73 9.78
-201.14 41.94
0 0
0 0
0 0
0 0
-49.04 301.95
-56.71 969.51
-496.48 129.68
-1019.5 115.46
49.04 -301.95
56.71 -969.51
496.48 -129.68
1019.5 -115.46
619197.19 -216106.59
608262.77 -225567.23
594987.54 -204922.61
565201.96 -206467.63
458664.58 -160078.96
450565.02 -167086.84
136322.96 -44843.65
114636.95 -39380.8
513782.4 -178452.08
496953.5 -183020.01
513001.04 -178006.64
496218.65 -182797.22
458664.58 -160078.96
MX MY
kN-m kN-m
450565.02 -167086.84
594987.54 -204922.61
565201.96 -206467.63
619197.19 -216106.59
608262.77 -225567.23
823681.63 -283372.07
780218.19 -284638.43
502090.68 -182242.95
535629.03 -203220.7
823681.63 -283372.07
780218.19 -284638.43
635884.43 -218375.71
599593.05 -218281.87
594987.54 -204922.61
565201.96 -206467.63
594987.54 -204922.61
565201.96 -206467.63
554090.66 -191469.52
530810.88 -194653.39
554090.66 -191469.52
530810.88 -194653.39
458664.58 -160078.96
450565.02 -167086.84
458664.58 -160078.96
450565.02 -167086.84
594987.54 -160078.96
565201.96 -167086.84
458664.58 -204922.61
450565.02 -206467.63
823681.63 -283372.07
780218.19 -284638.43
823681.63 -283372.07
780218.19 -284638.43
823681.63 -283372.07
780218.19 -284638.43
762336.3 -263192.43
728631.57 -266917.07
762336.3 -263192.43
728631.57 -266917.07
619197.19 -216106.59
608262.77 -225567.23
619197.19 -216106.59
608262.77 -225567.23
458664.58 -160078.96
450565.02 -167086.84
MX MY
kN-m kN-m
458664.58 -160078.96
450565.02 -167086.84
823632.58 -283070.12
780161.48 -283668.91
823185.15 -283242.39
779198.69 -284522.96
823730.67 -283674.02
780274.91 -285607.94
824178.1 -283501.76
781237.7 -284753.89
762287.25 -262890.48
728574.85 -265947.55
761839.82 -263062.75
727612.06 -266801.6
762385.34 -263494.38
728688.28 -267886.58
762832.77 -263322.11
729651.07 -267032.53
619148.14 -215804.64
608206.06 -224597.72
618700.71 -215976.91
607243.27 -225451.77
619246.23 -216408.55
608319.49 -226536.74
619693.66 -216236.28
609282.27 -225682.69
458615.54 -159777.01
450508.3 -166117.32
458168.11 -159949.28
449545.51 -166971.37
458713.63 -160380.91
450621.73 -168056.35
459161.06 -160208.64
451584.52 -167202.3
824178.1 -159777.01
781237.7 -166117.32
458168.11 -283674.02
449545.51 -285607.94
458664.58 -160078.96
450565.02 -167086.84
635884.43 -218375.71
599593.05 -218281.87
635884.43 -218375.71
599593.05 -218281.87
635884.43 -218375.71
MX MY
kN-m kN-m
599593.05 -218281.87
582718.48 -200886.68
554884.64 -202923.36
582718.48 -200886.68
554884.64 -202923.36
458664.58 -160078.96
450565.02 -167086.84
458664.58 -160078.96
450565.02 -167086.84
635835.39 -218073.76
599536.33 -217312.36
635387.95 -218246.02
598573.54 -218166.41
635933.47 -218677.66
599649.76 -219251.39
636380.91 -218505.39
600612.55 -218397.34
582669.43 -200584.73
554827.93 -201953.85
582222 -200757
553865.14 -202807.9
582767.52 -201188.63
554941.35 -203892.88
583214.95 -201016.37
555904.14 -203038.83
458615.54 -159777.01
450508.3 -166117.32
458168.11 -159949.28
449545.51 -166971.37
458713.63 -160380.91
450621.73 -168056.35
459161.06 -160208.64
451584.52 -167202.3
636380.91 -159777.01
600612.55 -166117.32
458168.11 -218677.66
449545.51 -219251.39
362462.61 -143100.04
407124.54 -161610.23
93302.58 -34807.92
93251.81 -34853.85
120719.81 -45507.01
120672.79 -45567.61
543.18 -181.12
537.7 -184.05
MX MY
kN-m kN-m
-200.47 41.92
-177.68 41.52
0 0
0 0
0 0
0 0
-64.08 969.68
-60.89 1497.08
-1013.67 115.21
-1441.35 112.23
64.08 -969.68
60.89 -1497.08
1013.67 -115.21
1441.35 -112.23
615283.02 -240175.75
675508.08 -265226.51
576485.01 -223414.98
621049.15 -242031.69
455765.2 -177907.97
500376.36 -196464.08
120719.81 -45507.01
120672.79 -45567.61
504596.31 -196291.9
549183.17 -214875.17
503852.66 -196068.85
548467.79 -214649.61
455765.2 -177907.97
500376.36 -196464.08
576485.01 -223414.98
621049.15 -242031.69
615283.02 -240175.75
675508.08 -265226.51
796362.74 -308436.27
856517.27 -333577.92
543693.92 -214650.07
610686.81 -242415.35
796362.74 -308436.27
856517.27 -333577.92
612700.96 -237067.08
657250.99 -255701.97
576485.01 -223414.98
621049.15 -242031.69
576485.01 -223414.98
621049.15 -242031.69
540269.07 -209762.88
MX MY
kN-m kN-m
584847.31 -228361.41
540269.07 -209762.88
584847.31 -228361.41
455765.2 -177907.97
500376.36 -196464.08
455765.2 -177907.97
500376.36 -196464.08
576485.01 -177907.97
621049.15 -196464.08
455765.2 -223414.98
500376.36 -242031.69
796362.74 -308436.27
856517.27 -333577.92
796362.74 -308436.27
856517.27 -333577.92
796362.74 -308436.27
856517.27 -333577.92
742038.82 -287958.12
802214.51 -313072.5
742038.82 -287958.12
802214.51 -313072.5
615283.02 -240175.75
675508.08 -265226.51
615283.02 -240175.75
675508.08 -265226.51
455765.2 -177907.97
500376.36 -196464.08
455765.2 -177907.97
500376.36 -196464.08
796298.66 -307466.59
856456.38 -332080.85
795349.07 -308321.06
855075.92 -333465.7
796426.82 -309405.96
856578.16 -335075
797376.41 -308551.49
857958.62 -333690.15
741974.74 -286988.43
802153.62 -311575.42
741025.16 -287842.9
800773.16 -312960.27
742102.91 -288927.8
802275.41 -314569.58
743052.49 -288073.33
803655.87 -313184.72
MX MY
kN-m kN-m
615218.94 -239206.07
675447.19 -263729.43
614269.35 -240060.54
674066.73 -265114.28
615347.1 -241145.44
675568.97 -266723.59
616296.69 -240290.97
676949.43 -265338.74
455701.12 -176938.28
500315.47 -194967.01
454751.53 -177792.75
498935 -196351.86
455829.28 -178877.65
500437.25 -197961.16
456778.87 -178023.18
501817.71 -196576.31
797376.41 -176938.28
857958.62 -194967.01
454751.53 -309405.96
498935 -335075
455765.2 -177907.97
500376.36 -196464.08
612700.96 -237067.08
657250.99 -255701.97
612700.96 -237067.08
657250.99 -255701.97
612700.96 -237067.08
657250.99 -255701.97
565620.23 -219319.35
610188.6 -237930.61
565620.23 -219319.35
610188.6 -237930.61
455765.2 -177907.97
500376.36 -196464.08
455765.2 -177907.97
500376.36 -196464.08
612636.88 -236097.4
657190.1 -254204.9
611687.29 -236951.87
655809.64 -255589.75
612765.04 -238036.77
657311.88 -257199.05
613714.63 -237182.3
658692.34 -255814.2
565556.15 -218349.66
MX MY
kN-m kN-m
610127.71 -236433.53
564606.56 -219204.13
608747.25 -237818.38
565684.31 -220289.03
610249.49 -239427.68
566633.9 -219434.56
611629.95 -238042.83
455701.12 -176938.28
500315.47 -194967.01
454751.53 -177792.75
498935 -196351.86
455829.28 -178877.65
500437.25 -197961.16
456778.87 -178023.18
501817.71 -196576.31
613714.63 -176938.28
658692.34 -194967.01
454751.53 -238036.77
498935 -257199.05
662535.29 -241501.13
673487.73 -245769.87
163094.85 -52577.2
163057.49 -52645.3
202446.77 -69682.44
202404.08 -69755.73
567.31 -190.05
561.5 -192.79
-183.7 41.94
-159.11 41.06
0 0
0 0
0 0
0 0
-56.23 1474.21
-52.75 1412.37
-1494.17 120.94
-1336.49 116.5
56.23 -1474.21
52.75 -1412.37
1494.17 -120.94
1336.49 -116.5
1114600.69 -397005.75
1129336.05 -402860.49
1028076.91 -363760.77
1038949.3 -368170.91
MX MY
kN-m kN-m
825630.14 -294078.33
836545.22 -298415.18
202446.77 -69682.44
202404.08 -69755.73
907176.15 -322141.36
918068.35 -326510.26
906425.15 -321909.37
917347.74 -326276.41
825630.14 -294078.33
836545.22 -298415.18
1028076.91 -363760.77
1038949.3 -368170.91
1114600.69 -397005.75
1129336.05 -402860.49
1418270.84 -501529.41
1432942.17 -507494.09
993802.93 -362251.7
1010231.59 -368654.81
1418270.84 -501529.41
1432942.17 -507494.09
1088810.94 -384665.51
1099670.52 -389097.63
1028076.91 -363760.77
1038949.3 -368170.91
1028076.91 -363760.77
1038949.3 -368170.91
967342.88 -342856.04
978228.08 -347244.19
967342.88 -342856.04
978228.08 -347244.19
825630.14 -294078.33
836545.22 -298415.18
825630.14 -294078.33
836545.22 -298415.18
1028076.91 -294078.33
1038949.3 -298415.18
825630.14 -363760.77
836545.22 -368170.91
1418270.84 -501529.41
1432942.17 -507494.09
1418270.84 -501529.41
1432942.17 -507494.09
1418270.84 -501529.41
1432942.17 -507494.09
1327169.79 -470172.31
MX MY
kN-m kN-m
1341860.33 -476104.01
1327169.79 -470172.31
1341860.33 -476104.01
1114600.69 -397005.75
1129336.05 -402860.49
1114600.69 -397005.75
1129336.05 -402860.49
825630.14 -294078.33
836545.22 -298415.18
825630.14 -294078.33
836545.22 -298415.18
1418214.61 -500055.2
1432889.41 -506081.71
1416776.67 -501408.47
1431605.68 -507377.59
1418327.07 -503003.62
1432994.92 -508906.46
1419765.01 -501650.35
1434278.66 -507610.58
1327113.56 -468698.1
1341807.58 -474691.63
1325675.63 -470051.37
1340523.84 -475987.51
1327226.03 -471646.52
1341913.08 -477516.38
1328663.96 -470293.25
1343196.82 -476220.5
1114544.45 -395531.54
1129283.29 -401448.12
1113106.52 -396884.8
1127999.56 -402743.99
1114656.92 -398479.95
1129388.8 -404272.86
1116094.85 -397126.69
1130672.54 -402976.99
825573.9 -292604.12
836492.47 -297002.8
824135.97 -293957.39
835208.73 -298298.68
825686.37 -295552.54
836597.97 -299827.55
827124.3 -294199.27
837881.71 -298531.67
1419765.01 -292604.12
1434278.66 -297002.8
MX MY
kN-m kN-m
824135.97 -503003.62
835208.73 -508906.46
825630.14 -294078.33
836545.22 -298415.18
1088810.94 -384665.51
1099670.52 -389097.63
1088810.94 -384665.51
1099670.52 -389097.63
1088810.94 -384665.51
1099670.52 -389097.63
1009856.7 -357489.35
1020732.93 -361892.89
1009856.7 -357489.35
1020732.93 -361892.89
825630.14 -294078.33
836545.22 -298415.18
825630.14 -294078.33
836545.22 -298415.18
1088754.71 -383191.3
1099617.77 -387685.26
1087316.77 -384544.56
1098334.03 -388981.13
1088867.17 -386139.71
1099723.28 -390510
1090305.11 -384786.45
1101007.01 -389214.13
1009800.47 -356015.15
1020680.18 -360480.52
1008362.53 -357368.41
1019396.44 -361776.4
1009912.93 -358963.56
1020785.69 -363305.27
1011350.86 -357610.3
1022069.42 -362009.39
825573.9 -292604.12
836492.47 -297002.8
824135.97 -293957.39
835208.73 -298298.68
825686.37 -295552.54
836597.97 -299827.55
827124.3 -294199.27
837881.71 -298531.67
1090305.11 -292604.12
1101007.01 -297002.8
824135.97 -386139.71
MX MY
kN-m kN-m
835208.73 -390510
Period
Case Mode UX UY UZ SumUX SumUY SumUZ RX RY
sec
Modal 1 1792342.372 1.207E-06 0.0017 0 1.207E-06 0.0017 0 0.0001 0
Modal 2 1792342.372 0.0017 1.207E-06 0 0.0017 0.0017 0 0 0.0001
Modal 3 1452396.42 0.0006 0.0005 0 0.0023 0.0022 0 2.178E-05 2.382E-05
Modal 4 1452396.42 0.0005 0.0006 0 0.0028 0.0028 0 2.382E-05 2.178E-05
Modal 5 0.351 0.0129 0.0001 0 0.0158 0.003 0 7.42E-06 0.001
Modal 6 0.303 0.0121 0.0009 0 0.0279 0.0038 0 0.0002 0.0008
Modal 7 0.289 0.0003 0.0005 0 0.0282 0.0043 0 0.0001 7.105E-06
Modal 8 0.262 0.0002 0.005 0 0.0283 0.0093 0 0.0009 3.794E-05
Modal 9 0.213 1.965E-06 0.5887 0 0.0283 0.598 0 0.2393 0.0001
Modal 10 0.188 0.0098 0.0141 0 0.0382 0.6122 0 0.0114 0.0023
Modal 11 0.166 0.0046 0.0067 0 0.0428 0.6188 0 0.0133 0.0006
Modal 12 0.156 0.0017 0.0325 0 0.0445 0.6513 0 0.1205 0.0006
Modal 13 0.133 0.522 0.0003 0 0.5664 0.6516 0 0.0017 0.2688
Modal 14 0.108 2.962E-06 4.783E-05 0 0.5664 0.6516 0 0.0001 1.303E-06
Modal 15 0.106 0.0002 0 0 0.5666 0.6516 0 0.0001 2.049E-05
Static Dynamic
Case ItemType Item
% %
Modal Acceleration UX 100 56.66
Modal Acceleration UY 100 65.16
Modal Acceleration UZ 0 0
Period
Case Mode UX UY UZ RZ
sec
Modal 1 1792342.372 0.001 0.999 0 0
Modal 2 1792342.372 0.999 0.001 0 0
Modal 3 1452396.42 0.522 0.478 0 0
Modal 4 1452396.42 0.478 0.522 0 0
Modal 5 0.351 0.015 0 0 0.985
Modal 6 0.303 0.008 0 0 0.991
Modal 7 0.289 0 0 0 1
Modal 8 0.262 0 0 0 1
Modal 9 0.213 0.002 0.819 0 0.18
Modal 10 0.188 0.008 0.009 0 0.983
Modal 11 0.166 0 0 0 1
Modal 12 0.156 0.001 0.016 0 0.983
Modal 13 0.133 0.549 0.001 0 0.45
Modal 14 0.108 0.003 0.46 0 0.537
Modal 15 0.106 0 0 0 1
B750x900 B750x900
B400 x 700
B750x900
B750x900
B750x900 B750x900
B750x900
B750x900
B750x900 B750x900
B250x500
B750x900
B750x900
B750x900 B750x900
B750x900 B750x900
B750x900
B750x900
B500X800 B500X800 B500X800
B750x900
B750x900
B750x900
B300 x 700
B400 x 700
B750x900
B750x900
B250x500
B750x900 B750x900
B250x500
B750x900
B750x900
B750x900 B750x900
B250x500
B750x900 B750x900
B400 x 700
B750x900
B250x500
B750x900
B750x900
B400 x 700
B750x900 B750x900
B250x500
B750x900
B750x900
B750x900 B750x900
B250x500
B750x900 B750x900
B500X700
B500x900
B750x900
UKB406X140X39
Existing Beam (250x1000)
Exisitng Beam (200x510)
UKB254X146X37
UKB406X178X67
UKB406X178X67
UKB406X178X67
UKB254X146X37
Existing Beam (350x900)
UKB254X146X37 UKB254X146X37 UKB254X146X37
UKB254X146X37 UKB254X146X37
Exisitng Beam (200x550) UKB254X146X37
UKB533X210X82 UKB533X210X82
Exisitng Beam (200x550)
UKB406X140X39
UKB406X140X39
UKB406X140X39
UKB406X140X39
UKB406X140X39
UKB406X140X39
UKB406X140X39
Ext Beam (700x350)
B400x900
Exisitng Beam (200x550) UKB533X210X82
UK
UKB533X210X82
UKB406X140X39
UKB406X140X39
UKB406X140X39
B400 x 700
B4
UKB406X178X67
B400 x 700
06
UKB533X210X82
X1
4
B400 x 700
0X
39
Existing Beam (300x700) Ext Beam (700x350) UKB533X210X82
Ext Beam (700x350)
UK
B1000x1000 UKB406X178X67
UKB533X210X82
UKB406X140X39
UKB406X140X39
B4
06
X1
Existing Beam (300x700)
B400x900
4 0X
39
UKB533X210X82 UKB356X127X39
Ext Beam (700x350)
B1000x1000
UKB254X146X37
Existing Beam (300x700)
UKB406X178X67
UKB406X178X67
UKB406X178X67
UKB254X146X37
UKB254X146X37 UKB254X146X37
UKB254X146X37
UKB254X146X37
Exisitng Beam (200x550)
UKB254X146X37 UKB254X146X37
UKB254X146X37
UKB406X140X39
UKB406X140X39
UKB406X140X39
Existing Beam (350x700)
UKB406X140X39
Existing Beam (250x550)
UKB406X140X39
UKB254X146X37
UKB406X140X39
UKB406X140X39
UKB406X140X39
2021 12 27 New Staircase st fdn v11b.EDB Plan View - Concourse - Z = 8.86 (m)
ETABS 19.0.2 1/7/2022
B300x850
B300x1100
B300x850
Exisitng Beam (400x1930) Existing Beam (450x1930)
Existing Beam (300x700)
B300x850
Exisitng Beam (400x1930) Existing Beam (450x1930)
B300x1100
B300x850
B300x850
B300x850
B300x1100
B300x850
B1000x1000
Existing Beam (250x750)
B300x1100
B300x850
B300x850
B300x1100
B300x850
B1000x1000
B300x1100
B300x850
2021 12 27 New Staircase st fdn v11b.EDB Plan View - Lower Platform - Z = 15.79 (m)
ETABS 19.0.2
UKB254X146X37
UKB254X146X37
UKB254X146X37
UKB254X146X37 UKB254X146X37
UKB254X146X37
2.5 2.5
2.5 2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5
2.5 2.5
2.5 2.5
2.5
2.5
2.5
2.5 2.5
2021 12 27 New Staircase st fdn v11b.EDB Plan View - Ground - Z = 3 (m) Uniform Loads Gravity (SDL)
ETABS 19.0.2 1/7/2022
25
25
25
25
25
7
7
25
25
25
25
2021 12 27 New Staircase st fdn v11b.EDB 3-D View Frame Span Loads Gravity (SDL)
ETABS 19.0.2 1/7/2022
2021 12 27 New Staircase st fdn v11b.EDB 3-D View Frame Span Loads Gravity (DL)
ETABS 19.0.2 1/7/2022
2.5
2.5
3.25
3.25
3.25 3.25 3.25 3.25
3.25
3.25
3.25
3.25
3.25 3.25 3.25
2.5
2.5
2.5
2.5
2021 12 27 New Staircase st fdn v11b.EDB Plan View - Concourse - Z = 8.86 (m) Uniform Loads Gravity (SDL)
ETABS 19.0.2 1/7/2022
2.5 2.5 7
1.2
7 6
1.2 1.2
8 1.2 13 13 1.2
9
1.2
1.2
8 9 7 7
7 1.2 7
1.2 5 3
7 7
6
1.2 1.2
10 8 8
6
7 1.2 1.2 1.2
7.5 8 8
10 1.2 1.2
9 7 7
6.5 1.2 8
7 7 7
5.5 7
1.2
5.5 1.2 1.2 1.2
1.2 5.5
1.2
3.5 7 7 7
2021 12 27 New Staircase st fdn v11b.EDB Plan View - Concourse - Z = 8.86 (m) Frame Span Loads Gravity (SDL)
ETABS 19.0.2 1/7/2022
3.25 3.25
2.5
9 9
2.5
3.25 3.25
3.25 3.25
9 9 9 2.5
9 2.5
3.25
3.25
3.25
3.25
3.25 3.25
9 2.5
9
9
9 9 2.5
9
3.25 3.25
3.25
2021 12 27 New Staircase st fdn v11b.EDB Plan View - Lower Platform - Z = 15.79 (m) Uniform Loads Gravity (SDL)
ETABS 19.0.2 1/7/2022
2.5
2.5
2.5
2.5
2.5
2.5
2021 12 27 New Staircase st fdn v11b.EDBPlan View - Ground- walkway Rf - Z = 5.93 (m) Uniform Loads Gravity (SDL)
ETABS 19.0.2 1/7/2022
1.8 3.25
2021 12 27 New Staircase st fdn v11b.EDB Plan View - Upper Platform - Z = 18.82 (m) Uniform Loads Gravity (SDL)
Imposed Loads
ETABS 19.0.2 1/7/2022
7.5 7.5 5
5 5
5 5 5
5 5
5 5 5
5 5
5
5
5 5
2021 12 27 New Staircase st fdn v11b.EDB Plan View - Ground - Z = 3 (m) Uniform Loads Gravity (LL)
ETABS 19.0.2 1/7/2022
5 5 5 5 5
5 5 5 5 5
5
5 5 5 5
5 5
5
5
5 5 5 5
5
5 5 5
5
2021 12 27 New Staircase st fdn v11b.EDB Plan View - Concourse - Z = 8.86 (m) Uniform Loads Gravity (LL)
ETABS 19.0.2 1/7/2022
5 5
7.5 7.5
5
5 5
5 5
7.5
7.5 7.5 7.5 5
7.5
7.5 5
5 5
5 5
7.5
7.5
7.5
7.5 7.5 5
7.5
5 5
2021 12 27 New Staircase st fdn v11b.EDB Plan View - Lower Platform - Z = 15.79 (m) Uniform Loads Gravity (LL)
ETABS 19.0.2 1/7/2022
2021 12 27 New Staircase st fdn v11b.EDBPlan View - Ground- walkway Rf - Z = 5.93 (m) Uniform Loads Gravity (LL)
ETABS 19.0.2 1/7/2022
0.75
0.75 0.75 0.75 0.75 0.75 0.75 0.75 0.75
0.75 1.5
2021 12 27 New Staircase st fdn v11b.EDB Plan View - Upper Platform - Z = 18.82 (m) Uniform Loads Gravity (LL)
Accidental loads
ETABS 19.0.2 1/7/2022
135
265
2021 12 27 New Staircase st fdn v11b.EDB 3-D View Frame Span Loads (Acci Fx)
ETABS 19.0.2 1/7/2022
5
13
5
26
2021 12 27 New Staircase st fdn v11b.EDB 3-D View Frame Span Loads (Acci Fy)
Pile Reactions
ETABS 19.0.2 1/7/2022
224 226
Fz = 969.79 Fz = 332.84
228
Fz = 1142.09
66 158 68
Fz = 1528.84 Fz = 823.23
Fz = 1428.44
163
Fz = 1306.68
285 287
Fz = 1286.13 Fz = 1318.79
164
Fz = 1307.3
65 145 67
Fz = 1515.77 Fz = 1348.2
Fz = 1132.33
479
Fz = 978.13
245
Fz = 991.15
182 169 64
178
Fz = 911.48 Fz = 1317.04
Fz = 749.87
Fz = 1307.83 176
392
Fz = 1123.49
Fz = 1103.39
632
Fz = 1072.44 174
197
Fz = 1052.99
Fz = 1209.43199 168 63
Fz = 1034.69 Fz = 1195.61
Fz = 730.08
62 172 60
Fz = 1069.87
187 Fz = 1426.65
Fz = 810.51
Fz = 1390.83
289 144
Fz = 1220.36 Fz = 1274.02
189
191
Fz = 1232.87 161 59
Fz = 1163.42 Fz = 779.53 Fz = 1255.68
452 275
Fz = 439.63 Fz = 345.41
2021 12 27 New Staircase st fdn v11b.EDB Plan View - Base - Z = 0 (m) Restraint Reactions (SLS ENVE) Step 2/2 [kN, kN-m]
ETABS 19.0.2 1/7/2022
224 226
Fz = 1337 Fz = 458.74
228
Fz = 1582.75
66 158 68
Fz = 2137.97 Fz = 1147.43
Fz = 1988.8
163
Fz = 1820.58
285 287
Fz = 1783.45 Fz = 1830.65
164
Fz = 1814.31
65 145 67
Fz = 2110.76 Fz = 1883.34
Fz = 1577.75
479
Fz = 1355.19
245
Fz = 1383.12
182 169 64
178
Fz = 1276.1 Fz = 1840.66
Fz = 1042.8
Fz = 1829.1 176
392
Fz = 1564.29
Fz = 1534.13
632
Fz = 1491.15 174
197
Fz = 1467.29
Fz = 1689.83199 168 63
Fz = 1448.65 Fz = 1676.34
Fz = 1017.03
62 172 60
Fz = 1485.39
187 Fz = 2001.34
Fz = 1129.78
Fz = 1931.64
289 144
Fz = 1694.02 Fz = 1769.84
189
191
Fz = 1725.4 161 59
Fz = 1632.59 Fz = 1081.04 Fz = 1746.22
452 275
Fz = 609.91 Fz = 476.35
2021 12 27 New Staircase st fdn v11b.EDB Plan View - Base - Z = 0 (m) Restraint Reactions (Set B-ENVE) Step 2/2 [kN, kN-m]
Pile
SteelReactions
Design- Concourse Level
ETABS 19.0.2 1/7/2022
0.204
0.793 0.277 0.567
0.218
0.007
0.646
0.578
0.501
0.278 0.585 0.600
0.330 0.339
0.347
0.317
0.619 0.184
0.327
0.
43
2
0.303
0.067
0.016
0.619
0.
0.003
70
4
0.269
0.320 0.754
0.829
0.494
0.251
0.015
0.523 0.600
0.284
0.296 0.340
0.409
0.380
0.181
0.107
0.070
0.267
0.130
0.172
0.068
0.091
0.052
0.027
0.143
0.036
0.051
Level Element Unique Name Length (mm) Location (mm) Combo Design Type Element Type
Concourse B157 98 4300 4300 Set B -UDCon7-4 Beam DCL MRF
Design Parameters
Section Properties
A (cm²) I yy (cm⁴) i yy (mm) W el,yy (cm³) A v,y (cm²) W pl,yy (cm³) I yz (cm⁴) I t (cm⁴)
47.2 5537 108.3 432.6 17.6 483 0 15.3
I zz (cm⁴) i zz (mm) W el,zz (cm³) A v,z (cm²) W pl,zz (cm³) I w (cm⁶) h (mm)
571 34.8 78 32.4 119 85610.1 256
A eff (cm²) e Ny (mm) e Nz (mm) W ef,yy (cm³) W ef,zz (cm³)
47.2 0 0 432.6 78
Material Properties
Location (mm) N Ed (kN) M Ed,yy (kN-m) M Ed,zz (kN-m) V Ed,z (kN) V Ed,y (kN) T Ed (kN-m)
4300 0.04 0 0 54.91 -0.43 -9.589E-04
Basic Factors
Moment Designs
Moment Designs
Shear Design
V Ed Force (kN) V c,Rd Capacity (kN) T Ed /Torsion (kN-m) Stress Ratio Status Check
Major (z) 54.91 361.31 -9.589E-04 0.152 OK
Minor (y) 0.43 665 -9.589E-04 0.001 OK
Shear Design
Left End Reaction (kN) Load Combo Right End Reaction (kN) Load Combo
54.91 Set C -UDCon8-4 54.91 Set C -UDCon8-4
Level Element Unique Name Length (mm) Location (mm) Combo Design Type Element Type
Concourse B306 280 5000 4700 Set B -UDCon7-2 Beam DCL MRF
Design Parameters
Section Properties
A (cm²) I yy (cm⁴) i yy (mm) W el,yy (cm³) A v,y (cm²) W pl,yy (cm³) I yz (cm⁴) I t (cm⁴)
49.7 12508 158.6 628.5 27.6 724 0 10.7
I zz (cm⁴) i zz (mm) W el,zz (cm³) A v,z (cm²) W pl,zz (cm³) I w (cm⁶) h (mm)
410 28.7 57.8 25.3 90.8 154920.1 398
A eff (cm²) e Ny (mm) e Nz (mm) W ef,yy (cm³) W ef,zz (cm³)
49.7 0 0 628.5 57.8
Material Properties
Location (mm) N Ed (kN) M Ed,yy (kN-m) M Ed,zz (kN-m) V Ed,z (kN) V Ed,y (kN) T Ed (kN-m)
4700 -1.33 14.76 0.03 49.23 0.1 7.789E-04
Basic Factors
Moment Designs
Moment Designs
Shear Design
V Ed Force (kN) V c,Rd Capacity (kN) T Ed /Torsion (kN-m) Stress Ratio Status Check
Major (z) 49.23 489.82 7.789E-04 0.1 OK
Minor (y) 0.1 519.14 7.789E-04 1.944E-04 OK
Shear Design
Left End Reaction (kN) Load Combo Right End Reaction (kN) Load Combo
2.87 Set C -UDCon8-4 49.16 Set C -UDCon8-4
Level Element Unique Name Length (mm) Location (mm) Combo Design Type Element Type
Concourse B123 35 9670 9670 Set B -UDCon7-2 Beam DCL MRF
Design Parameters
Section Properties
A (cm²) I yy (cm⁴) i yy (mm) W el,yy (cm³) A v,y (cm²) W pl,yy (cm³) I yz (cm⁴) I t (cm⁴)
85.5 24331 168.7 1188.6 38.5 1346 0 46.1
I zz (cm⁴) i zz (mm) W el,zz (cm³) A v,z (cm²) W pl,zz (cm³) I w (cm⁶) h (mm)
1365 40 152.7 52 237 531669.1 409.4
A eff (cm²) e Ny (mm) e Nz (mm) W ef,yy (cm³) W ef,zz (cm³)
85.5 0 0 1188.6 152.7
Material Properties
Location (mm) N Ed (kN) M Ed,yy (kN-m) M Ed,zz (kN-m) V Ed,z (kN) V Ed,y (kN) T Ed (kN-m)
9670 -20.56 0 0 132.82 0.04 -2.7E-06
Basic Factors
Moment Designs
Moment Designs
Shear Design
V Ed Force (kN) V c,Rd Capacity (kN) T Ed /Torsion (kN-m) Stress Ratio Status Check
Major (z) 132.82 789.89 -2.7E-06 0.168 OK
Minor (y) 0.04 1065.57 -2.7E-06 4.219E-05 OK
Shear Design
Left End Reaction (kN) Load Combo Right End Reaction (kN) Load Combo
128.71 Set C -UDCon8-4 132.82 Set C -UDCon8-4
Level Element Unique Name Length (mm) Location (mm) Combo Design Type Element Type
Concourse B343 493 7000 7000 Set B -UDCon7-4 Beam DCL MRF
Design Parameters
Section Properties
A (cm²) I yy (cm⁴) i yy (mm) W el,yy (cm³) A v,y (cm²) W pl,yy (cm³) I yz (cm⁴) I t (cm⁴)
105 47539 212.8 1799.7 54.5 2059 0 51.5
I zz (cm⁴) i zz (mm) W el,zz (cm³) A v,z (cm²) W pl,zz (cm³) I w (cm⁶) h (mm)
2007 43.7 192.2 56.8 300 1328425.7 528.3
A eff (cm²) e Ny (mm) e Nz (mm) W ef,yy (cm³) W ef,zz (cm³)
105 0 0 1799.7 192.2
Material Properties
Location (mm) N Ed (kN) M Ed,yy (kN-m) M Ed,zz (kN-m) V Ed,z (kN) V Ed,y (kN) T Ed (kN-m)
7000 22.36 0 0 59.44 -0.06 0
Basic Factors
Moment Designs
Moment Designs
Shear Design
V Ed Force (kN) V c,Rd Capacity (kN) T Ed /Torsion (kN-m) Stress Ratio Status Check
Major (z) 59.44 1116.96 0 0.053 OK
Minor (y) 0.06 1164.53 0 4.913E-05 OK
Shear Design
0.043
0.065
0.50
0.079
0.085
0.104
0.068
0.041 0.073
0.068
0.70
0.033 0.042 0.040
0.90
Plan View - Upper Platform - Z = 18.82 (m) Steel P-M Interaction Ratios (Eurocode 3-2005)
1.00
1/7/2022
ETABS 19.0.2 License #*14FRZ9AFARY49RL
Level Element Unique Name Length (mm) Location (mm) Combo Design Type Element Type
Upper Platform B150 412 2695 2695 Set B -UDCon7-3 Beam DCL MRF
Design Parameters
Section Properties
A (cm²) I yy (cm⁴) i yy (mm) W el,yy (cm³) A v,y (cm²) W pl,yy (cm³) I yz (cm⁴) I t (cm⁴)
47.2 5537 108.3 432.6 17.6 483 0 15.3
I zz (cm⁴) i zz (mm) W el,zz (cm³) A v,z (cm²) W pl,zz (cm³) I w (cm⁶) h (mm)
571 34.8 78 32.4 119 85610.1 256
A eff (cm²) e Ny (mm) e Nz (mm) W ef,yy (cm³) W ef,zz (cm³)
47.2 0 0 432.6 78
Material Properties
Location (mm) N Ed (kN) M Ed,yy (kN-m) M Ed,zz (kN-m) V Ed,z (kN) V Ed,y (kN) T Ed (kN-m)
2695 -0.2 -12.03 -0.08 8.83 0.3 0
Basic Factors
Moment Designs
Moment Designs
Shear Design
V Ed Force (kN) V c,Rd Capacity (kN) T Ed /Torsion (kN-m) Stress Ratio Status Check
Major (z) 8.83 361.31 0 0.024 OK
Minor (y) 0.3 665 0 4.56E-04 OK
Shear Design
Left End Reaction (kN) Load Combo Right End Reaction (kN) Load Combo
8.83 Set C -UDCon8-4
UKB406X140X39 (4)
UKB406X140X39 (4)
UKB406X140X39 (4)
UKB406X140X39 (3,5)
UKB406X140X39 (7)
UKB406X140X39 (7)
UKB406X140X39 (7)
UKB406X140X39 (7)
UKB533X210X82 (8)
UKB406X140X39 (4)
UKB406X140X39 (4)
UKB406X140X39 (4)
UKB406X178X67 (3)
UKB533X210X82 (8)
UKB533X210X82 (8)
End Reactions
Top Cope Bot. Cope Constr. Dead SDL Live NR Combo Factored
I end (kN) 0 mm 0 mm 0.00 22.86 18.77 28.87 Set B -UDCon7-4 99.50
J end (kN) 0 mm 0 mm 0.00 22.89 18.79 28.92 Set B -UDCon7-2 99.65
Strength Checks
Section Properties
End Reactions
Top Cope Bot. Cope Constr. Dead SDL Live NR Combo Factored
I end (kN) 0 mm 0 mm 0.00 37.52 56.56 53.06 Set B -UDCon7-4 206.59
J end (kN) 18.2 mm 18.2 mm 0.00 37.52 99.18 61.99 Set B -UDCon7-2 277.54
Strength Checks
Section Properties
Beam 7.75 2.375 11.39kN/m 148203.3 148203.3/2.375 2/3*4.75 1*117.68 1.7 13.618
Licensee
AECOM Singapore Pte Ltd
300 Beach Road
#03-00 The Concourse
Singapore 199555
10479063400712WPN11
Input
General
Design Code List Singapore - Eurocode 2*SAVED*
Material List Singapore - Singapore Eurocode Materials*SAVED*
Reinforcement Type List Reinforced
Member Type List Beam
Panel Type List Internal
Strip Type List One way - Nominal Width
Column Stiffness List Equivalent Column
Concrete Type List Standard Concrete
Concrete - Spanning Members List C32/40MPa
Concrete - Columns List C32/40MPa
Top Reinforcement Cover mm 50
Bottom Reinforcement Cover mm 50
Top Reinforcement Axis Depth Limit mm 30
Bottom Reinforcement Axis Depth Limit mm 30
Concrete Unit Weight kn/m3 25
Self Weight Definition List Program Calculated
Pattern Live Load Y/N
Earthquake Design List None
Moment Redistribution % 0
Design Surface Levels List Extreme Surfaces
Eurocode Ultimate Load Combination Basis List Eurocode Eqn 6.10
Due to the different Concrete Strength types in the Design Standard and Materials in this run, the concrete strengths shown in the materials data have been
multiplied in the calculatiuons by 0.8
Span
Span Span Slab Panel Panel
Length Depth Width Width
Left Right
mm mm mm mm
LE 0
1 9600 750 750 750
RE 0
Columns
Column Column Support Transverse Transverse
Grid Type Column prestress
Reference spacing (P/A)
A List mm MPa
1 1 Knife-Edge 750
2 2 Knife-Edge 750
RAPT 6.6.8.0 Project Name: J110 Page 2/13
Licensee: AECOM Singapore Pte Ltd 1/6/2022 8:28:30 PM License No.: 10479063400712WPN11
Beams
Beam Beam Beam Beam Effective
Number Depth Width Width Flange
at Width
Slab
mm mm mm mm
1 900 750 750 750
Load Cases
Load Load Type Load Definition Live Load Description
Case Deflection Case
kN/m1 2
20
15
10
L3
5
0
0 9600mm
20
15 L2
10
5
0
0 9600mm
20 L1
15
10
5
0
1 2
kN/m1 2
20
15
10 L1
5
0
0 9600mm
kN/m1 2
20
15 L1
10
5
0
0 9600mm
RAPT 6.6.8.0 Project Name: J110 Page 4/13
Licensee: AECOM Singapore Pte Ltd 1/6/2022 8:28:36 PM License No.: 10479063400712WPN11
Reinforcement
Reinforcement Reinforcement Preferred Number
Use Type Bar Size of Legs
List List #
Flexural Bar H 500MPa
Flexural Mesh A 500MPa
Shear Option 1 H 500MPa 10 2
Shear Option 2 H 500MPa 10 4
Shear Option 3 H 500MPa 10 6
Punching Shear H 500MPa 10 2
Reinforcement
Maximum Minimum Minimum Minimum Span Minimum Span Infill Stagger
Bar Bar Continuous Reinforcement Reinforcement Bars Bars
Spacing Spacing Reinforcement into End into Internal
Support Support
mm mm #.# #.# #.# Y/N Y/N
Support Reinforcement 300 60 0 N N
Span Reinforcement 300 60 0 0 N N
Design Zones
Layer Steel Left End Distance to Bar stagger Top Right End Distance to Bar stagger Top Cover Maximum Minimum Preferred
Number type Reference left end of length at left Cover at Reference right end of length at right at Right Bar Size Bar Size bar size
Column bar end left end Column bar end end
List # mm mm mm # mm mm mm List List List
1 Bar 1 0 0 50 2 0 0 50 40 16 25
Design Zones
Layer Steel Left End Distance to Bar stagger Bottom Right End Distance to Bar stagger Bottom Maximum Minimum Preferred
Number type Reference left end of length at left Cover at left Reference right end of length at right Cover at Bar Size Bar Size bar size
Column bar end end Column bar end Right End
List # mm mm mm # mm mm mm List List List
1 Bar 1 0 0 50 2 0 0 50 40 16 25
-200
-400
-600
-800
0 9600mm
Design Data
Capacity Reduction factor (phi) for Flexure #.# 1
Capacity Reduction factor (phi) for Shear #.# 1
Capacity Reduction factor (phi) for Shear with transverse reinf #.# 1
Material Factor for Concrete in Flexure #.# 1.5
Material Factor for Concrete in Shear #.# 1.5
Material Factor for Reinforcement #.# 1.15
Maximum Ratio of Neutral Axis Depth for Ductility #.# 0.58
RAPT 6.6.8.0 Project Name: J110 Page 5/13
Licensee: AECOM Singapore Pte Ltd 1/6/2022 8:28:39 PM License No.: 10479063400712WPN11
Material Properties
Concrete : Standard Concrete : Concrete Strength Basis - Cube
Description A C32/40MPa
Characteristic Compressive Strength MPa 40
Mean Compressive Strength MPa 50
Lower Characteristic Tensile Strength MPa 2.12
Upper Characteristic Tensile Strength MPa 3.93
Concrete Density kg/m3 2447
Design Concrete Modulus MPa 31186.6
Mean Concrete Modulus MPa 33345.8
Basic Shrinkage Strain mm/mm 0
Shrinkage Multiplier #.# 1
Basic Creep Factor #.# 2.656
Creep Multiplier #.# 1
Concrete Strain at Peak Stress #.# 0.002
Squash Load Factor #.# 0.85
Concrete Strain Limit #.# 0.004
Strength Gain Rate List Normal
Maximum Aggregate Size mm 20
RAPT 6.6.8.0 Project Name: J110 Page 6/13
Licensee: AECOM Singapore Pte Ltd 1/6/2022 8:28:42 PM License No.: 10479063400712WPN11
Reinforcement Bar
Designation Type Yield Elastic Ductility Peak Peak Design Material Material Material Capacity Material Capacity Include as Description
Stress Modulus Strain Stress Strain Factor Factor Reduction Factor Reduction Factor Flexural
Limit Flexure Shear - Flexure - Shear Reinforcement for
Shear
H Deformed 500 2.05e5 N 0.05 540 90 -1 -1 -1 -1 Y
Elevation view
1 2
mm
0
-200
-400
-600
-800
0 9600mm
Plan view
1 2
mm
-200
200
0 9600mm
Warnings
Input
No errors or warnings were found.
Output
No errors or warnings were found.
Bending Moments
Load Cases
Column Actions
Col No. 1 Self Extra Dead Live
Weight Load Load
Moment Above kNm -0 -0 -0
Moment Below kNm -0 -0 -0
Reaction kN 155.4 25.44 50.4
Elastic Rotation #.# 7.86e-4 1.29e-4 2.55e-4
Elastic Axial Shortening mm 0 0 0
RAPT 6.6.8.0 Project Name: J110 Page 7/13
Licensee: AECOM Singapore Pte Ltd 1/6/2022 8:28:45 PM License No.: 10479063400712WPN11
Col No. 2 Self Extra Live Load
Weight Dead
Load
Moment Above kNm -0 -0 -0
Moment Below kNm -0 -0 -0
Reaction kN 155.4 25.44 50.4
Elastic Rotation #.# -7.86e-4 -1.29e-4 -2.55e-4
Elastic Axial Shortening mm 0 0 0
Load Combinations
Column Actions
Col No. 1 Characteristic Characteristic Service Service Ultimate Ultimate Ultimate Ultimate
Service Service (Reversal) Flexure Flexure Shear Shear
(Reversal) (Reversal) (Reversal)
Moment Above kNm 0 0 0 0 0 0 0 0
Moment Below kNm 0 0 0 0 0 0 0 0
Reaction kN 231.24 231.24 206.04 206.04 319.73 319.73 256.44 319.73
Elastic Rotation #.# 1.17e-3 1.17e-3 1.04e-3 1.04e-3 1.62e-3 1.62e-3 1.3e-3 1.62e-3
Elastic Axial Shortening mm 0 0 0 0 0 0 0 0
Col No. 2 Characteristic Characteristic Service Service Ultimate Ultimate Ultimate Ultimate
Service Service (Reversal) Flexure Flexure Shear Shear
(Reversal) (Reversal) (Reversal)
Moment Above kNm 0 0 0 0 0 0 0 0
Moment Below kNm 0 0 0 0 0 0 0 0
Reaction kN 231.24 231.24 206.04 206.04 319.73 319.73 256.44 319.73
Elastic Rotation #.# -1.17e-3 -1.17e-3 -1.04e-3 -1.04e-3 -1.62e-3 -1.62e-3 -1.3e-3 -1.62e-3
Elastic Axial Shortening mm 0 0 0 0 0 0 0 0
Ultimate Design
Flexure
1 2
kNm
-100 31.6 31.6
0
100
200
300
400
500
600
700
800
900 767
0 9600mm
1 2
kN
400
272
300
200
100
0
-100
-200
-300
-272
-400
0 9600mm
1 2
kN
400
272
300
200
100
0
-100
-200
-300
-272
-400
0 9600mm
Flexural Design
Ultimate
1 2
mm2
12000 0
600
0
-600
-1200
-1800
-2400
-3000
-3600 3198
0 9600mm
Reinforcement Top Total Bottom Total Top Ultimate Bottom Ultimate Min Top Min Bot
kNm1 2
-200
0
200
400
600
800
1000
1200
0 9600mm
1 2
0.02
0
-0.02
-0.04
-0.06
-0.08
-0.1
-0.12
-0.14
-0.16
0.15
0 9600mm
Service
Maximum Moment Condition
1 2
MPa MPa
-6 -4.62 -180
-4 -120
-2 -60
0 0
2 60
4 120
6 180
8 240
10 4.77 300
0 9600mm
Gross Stress Top Gross Stress Bottom Cracked Compression Reinforcement Tension Limits
Gross Stress Top Gross Stress Bottom Cracked Compression Reinforcement Tension Limits
Span 1
Design Comments:-
- Increase in stress from decompression to working exceeds 200MPa in at least one steel layer. Reinforcement has been added to reduce stress change
below this maximum value. Refer RAPT manual Section T.7.6
Permanent
1 2
MPa MPa
-6 -4.3 -180
-4 -120
-2 -60
0 0
2 60
4 120
6 180
8 240
10 4.49 300
0 9600mm
RAPT 6.6.8.0 Project Name: J110 Page 10/13
Licensee: AECOM Singapore Pte Ltd 1/6/2022 8:28:53 PM License No.: 10479063400712WPN11
Reversal Moment Condition
1 2
MPa MPa
-6 -4.3 -180
-4 -120
-2 -60
0 0
2 60
4 120
6 180
8 240
10 4.49 300
0 9600mm
Gross Stress Top Gross Stress Bottom Cracked Compression Reinforcement Tension Limits
Characteristic Service
Maximum Moment Condition
1 2
MPa MPa
-5.19
-6 -400
-3 -200
0 0
3 200
6 400
9 600
12 5.35 800
0 9600mm
Gross Stress Top Gross Stress Bottom Cracked Compression Reinforcement Tension Limits
Gross Stress Top Gross Stress Bottom Cracked Compression Reinforcement Tension Limits
Shear Design
Beam
Span 1
Locat V* Mv* Pv Mdec d Ast bv phi Vuc phi Vut phi Vu Phi Vumax phi VuMin phi Vus Theta Asv/s
Locat V* Mv* Pv Mdec d Ast bv phi Vuc phi Vut phi Vu Phi Vumax phi VuMin phi Vus Theta Asv/s
Punching
Column Head Critical Section
Column Bh a at u d fcv P/A Asw/s min V* Mv* V*eff VRd1 VRd2 Asv result
No.
A #.# mm mm mm mm MPa MPa mm2/mm kN kNm kN kN kN mm2 A
1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Check Not Carried Out!
2 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Check Not Carried Out!
Deflections
All Spans Loaded
Transfer
mm1 2
0
-6.87
-20
-40
-60 1398
0 9600mm
RAPT 6.6.8.0 Project Name: J110 Page 12/13
Licensee: AECOM Singapore Pte Ltd 1/6/2022 8:28:59 PM License No.: 10479063400712WPN11
Short Term
mm1 2
0
-10.6
-20
-40
-60 903
0 9600mm
Incremental
mm1 2
0
-20 -14.9
-40
-60 644
0 9600mm
mm1 2
0
-20
-21.1
-40
-60 454
0 9600mm
Detailed Reinforcement
Span 1
Top Reinforcement Bottom Reinforcement
Design Comments:-
- Span - 1 - Reinforcement added at left span contraflexure point for Offset of Bending Moment Diagram for Shear - 919.11mm2
- Span - 1 - Reinforcement added at right span contraflexure point for Offset of Bending Moment Diagram for Shear - 919.11mm2
Reinforcement Layout
1 2
mm
0
-200
-400
-600
-800
7-H25
0 9600mm
RAPT 6.6.8.0 Project Name: J110 Page 2/15
Licensee: AECOM Singapore Pte Ltd 1/6/2022 8:21:43 PM License No.: 10479063400712WPN11
Frame Description: G/A.1/8/2
Project Name: J110 Column Punching Transverse Transverse
Frame Description: G/A.1/8/2 Shear Check effective depth prestress
required difference (P/A)
Designer: SLT Y/N mm MPa
C:\Users\sujeevanleonard.tham\OneDrive - AECOM\Projects\J110\J110\OneDrive_2021-07-01\12. Southern 1 Y 0 0
Staircase\Design Files\Str\Beams\G,8,A.1,2.rpf 2 Y 0 0
Due to the different Concrete Strength types in the Design Standard and Materials in this run, the concrete strengths shown in the materials data have been 2. Extra Dead Load - Panel
multiplied in the calculatiuons by 0.8 Load Left End Left end of Load at Right Right end of Load at Description
reference load from left end End load from right
Span column reference reference reference end
column column column
Span Span Slab Panel Panel
# mm kN/m2 # mm kN/m2 A
Length Depth Width Width
Left Right 1 1 0 2.5 2 0 2.5 SDL
mm mm mm mm
LE 0
1 10600 200 1900 1900 2. Extra Dead Load - Point
RE 0 Load Reference Distance to Load Load Description
column Load from Length
reference
column
Columns # mm kN mm A
Column Column Support Column Column Column Column Column Column Transverse Capital Depth Pin Percentage Braced Column
1 1 2800 10 0
Grid Type Height Width Length Height Width Length Column below deepest Base Column frame at this Shortening
Reference Above Above Above below below below spacing section below Stiffness column Restrained 2 1 4000 10 0
A List mm mm mm mm mm mm mm mm Y/N % Y/N Y/N 3 1 6200 220 0
1 1 Column 3000 750 250 1000 750 250 1900 0 Y 5 Y N
2 2 Column 3000 750 250 1000 750 250 1900 0 Y 5 Y N
RAPT 6.6.8.0 Project Name: J110 Page 3/15 RAPT 6.6.8.0 Project Name: J110 Page 4/15
Licensee: AECOM Singapore Pte Ltd 1/6/2022 8:21:46 PM License No.: 10479063400712WPN11 Licensee: AECOM Singapore Pte Ltd 1/6/2022 8:21:51 PM License No.: 10479063400712WPN11
Frame Description: G/A.1/8/2 Frame Description: G/A.1/8/2
3. Live Load - Panel Load Combinations : Construction
Load Left End Left end of Load at Right Right end of Load at Live Description Load Description 1. Self 2. Extra 3. Live
reference load from left end End load from right Load Combination Weight Dead Load Load
column reference reference reference end reduction A #.# #.# #.#
column column column 1 Construction 1 0 0
# mm kN/m2 # mm kN/m2 #.# A
1 1 0 5 2 0 5 1 LL
Maximum Minimum Minimum Minimum Span Minimum Span Infill Stagger Include Strain Hardening of Reinforcement Y/N N
Bar Bar Continuous Reinforcement Reinforcement Bars Bars Beam Shear Critical Section Location List Code Critical Section
Spacing Spacing Reinforcement into End into Internal
Support Support
mm mm #.# #.# #.# Y/N Y/N
Span Reinforcement 300 60 0 0 N N Maximum Service Stress Change - Prestressed Sections MPa 150
Maximum Service Stress Change - Reinforced Sections MPa 200
Relative Humidity % 50
Average Temperature C. 20
Design Zones Prestress Losses Calculations based on List Program Default
Layer Steel Left End Distance to Bar stagger Top Right End Distance to Bar stagger Top Cover Maximum Minimum Preferred Crack Width Calculations List Code default
Number type Reference left end of length at left Cover at Reference right end of length at right at Right Bar Size Bar Size bar size
AS3600 Shrinkage and Temperature Reinforcement List Moderate
Column bar end left end Column bar end end
List # mm mm mm # mm mm mm List List List Degree of Restraint in Primary Direction % 0
1 Bar 1 0 0 40 2 0 0 40 40 20 32 Degree of Restraint in Secondary Direction % 0
Concrete Strength Gain Rate List N
Layer Minimum Maximum Minimum % in
Number Number of Spacing of Steel area as Flange Concrete Tensile Strength for Deflection Calculations- #.## x (Fc)n #.# -1
Bars Bars % Maximum Value of Ieff/Igross for Deflection Calculations #.# 0.6
# mm % % Total Deflection Warning Limit - Maximum Span/Deflection #.# 250
1 0 0 0 0 Total Deflection Warning Limit - Maximum Deflection mm 25
Incremental Deflection Warning Limit - Maximum Span/Deflection #.# 360
Incremental Deflection Warning Limit - Maximum Deflection mm 25
Design Zones Initial Time for Shrinkage List Full Shrinkage
Layer Steel Left End Distance to Bar stagger Bottom Right End Distance to Bar stagger Bottom Maximum Minimum Preferred Time of Loading in days #.# 10
Number type Reference left end of length at left Cover at left Reference right end of length at right Cover at Bar Size Bar Size bar size Age Adjustment Factor #.# 0.76
Column bar end end Column bar end Right End Concrete Strength at Time of Loading MPa 27.04
List # mm mm mm # mm mm mm List List List Loaded Period in years #.# 30
1 Bar 1 0 0 40 2 0 0 40 40 20 32 Tension stiffening Approach List Modified Concrete Tensile Modulus Method
Material Properties
Reinforcement Design Zones Concrete : Standard Concrete : Concrete Strength Basis - Cube
Description A C32/40MPa
1 2
Characteristic Compressive Strength MPa 40
mm
0 Mean Compressive Strength MPa 50
Lower Characteristic Tensile Strength MPa 2.12
-200 Upper Characteristic Tensile Strength MPa 3.93
Concrete Density kg/m3 2447
-400 MPa
Design Concrete Modulus 31186.6
-600 Mean Concrete Modulus MPa 33345.8
Basic Shrinkage Strain mm/mm 0
-800 Shrinkage Multiplier #.# 1
Basic Creep Factor #.# 2.656
0 10600mm
Creep Multiplier #.# 1
Design Data Concrete Strain at Peak Stress #.# 0.002
Capacity Reduction factor (phi) for Flexure #.# 1 Squash Load Factor #.# 0.85
Capacity Reduction factor (phi) for Shear #.# 1 Concrete Strain Limit #.# 0.004
Capacity Reduction factor (phi) for Shear with transverse reinf #.# 1 Strength Gain Rate List Normal
Material Factor for Concrete in Flexure #.# 1.5 Maximum Aggregate Size mm 20
Material Factor for Concrete in Shear #.# 1.5
Material Factor for Reinforcement #.# 1.15
Maximum Ratio of Neutral Axis Depth for Ductility #.# 0.58
Ductility Limit - Strain #.# 0
Reinforcement Bar
Y/N Designation Type Yield Elastic Ductility Peak Peak Design Material Material Material Capacity Material Capacity Include as Description
Ductility Check at Left End Column Y
Stress Modulus Strain Stress Strain Factor Factor Reduction Factor Reduction Factor Flexural
Ductility Check at Right End Column Y/N Y Limit Flexure Shear - Flexure - Shear Reinforcement for
Minimum Reinforcement Strength Limit - #.## x M* #.# 0 Shear
Flexural Critical Section - Consider Transverse Beams Y/N Y H Deformed 500 2.05e5 N 0.05 540 90 -1 -1 -1 -1 Y
Flexural Critical Section - Distance from centre of Support #.# -1
Beam Left Sideface Cover (Internal) mm 25
Beam Right Sideface cover mm 40 Nominal Bar Bar Area Bar Bar Stock
Prestress Minimum Reinforcement Basis List Program Default Bar Size Diameter Inertia Weight Length
Shear Enhancement at Supports Y/N N A mm mm2 mm4 kg/m mm
Ast Value in Shear Calculations List Calculated 10 10 78.5 491.07 0.62 12000
Limit Reinforcement Strain Y/N Y 13 13 132.7 1402.55 1.04 12000
RAPT 6.6.8.0 Project Name: J110 Page 7/15 RAPT 6.6.8.0 Project Name: J110 Page 8/15
Licensee: AECOM Singapore Pte Ltd 1/6/2022 8:22:00 PM License No.: 10479063400712WPN11 Licensee: AECOM Singapore Pte Ltd 1/6/2022 8:22:04 PM License No.: 10479063400712WPN11
Frame Description: G/A.1/8/2 Frame Description: G/A.1/8/2
Nominal Bar Bar Area Bar Bar Stock Col No. 1 Self Extra Dead Live
Bar Size Diameter Inertia Weight Length Weight Load Load
A mm mm2 mm4 kg/m mm Elastic Rotation #.# 4.56e-4 2.82e-4 5e-4
16 16 201.1 3218.29 1.58 12000 Elastic Axial Shortening mm -0 -0 -0
20 20 314.2 7857.14 2.47 12000
22 22 380.1 11503.6 2.98 12000 Col No. 2 Self Extra Live Load
25 25 490.9 19182.5 3.85 12000 Weight Dead
32 32 804.2 51492.6 6.31 12000 Load
40 40 1256.6 1.257e5 9.86 12000 Moment Above kNm -0.42 -0.27 -0.49
Moment Below kNm -375.47 -240.46 -432.82
Reaction kN 275.84 163.09 296.32
Elevation view
Elastic Rotation #.# -5.02e-4 -3.22e-4 -5.79e-4
1 2 Elastic Axial Shortening mm -0 -0 -0
mm
0
1 2
mm Col No. 2 Characteristic Characteristic Service Service Ultimate Ultimate Ultimate Ultimate
-800 Service Service (Reversal) Flexure Flexure Shear Shear
(Reversal) (Reversal) (Reversal)
-400 Moment Above kNm -1.18 -1.18 -0.94 -0.94 -1.67 -0.99 -0.99 -1.67
Moment Below kNm -1048.74 -1048.74 -832.33 -832.33 -1480.73 -877.69 -877.69 -1480.73
0 Reaction kN 735.25 735.25 587.09 587.09 1037.04 625.48 625.48 1037.04
Elastic Rotation #.# -1.4e-3 -1.4e-3 -1.11e-3 -1.11e-3 -1.98e-3 -1.17e-3 -1.17e-3 -1.98e-3
400 Elastic Axial Shortening mm -0 -0 -0 -0 -0 -0 -0 -0
800
0 10600mm
Ultimate Design
Full Elevation View Flexure
mm 1 2
kNm1 2
3000 -2100
-1203 -1353
-1400
2000 -700
0
1000 700
1400
0
2100
2800 2584
-1000
0 10600mm 0 10600mm
Warnings
Input Moment Moment 1 Moment 2
No errors or warnings were found.
1 2
Output kN
900 781
Warning:Total deflection in at least one span is greater than defined limit.
600
300
0
-300
Bending Moments -600
Load Cases -900
Column Actions -1200 -994
Col No. 1 Self Extra Dead Live 0 10600mm
Weight Load Load
Moment Above kNm 0.38 0.24 0.42 Shear Shear 1 Shear 2
Moment Below kNm 340.68 210.55 373.63
Reaction kN 233.99 127.26 224.38
RAPT 6.6.8.0 Project Name: J110 Page 9/15 RAPT 6.6.8.0 Project Name: J110 Page 10/15
Licensee: AECOM Singapore Pte Ltd 1/6/2022 8:22:07 PM License No.: 10479063400712WPN11 Licensee: AECOM Singapore Pte Ltd 1/6/2022 8:22:10 PM License No.: 10479063400712WPN11
Frame Description: G/A.1/8/2 Frame Description: G/A.1/8/2
Shear
1 2
0.204
0.23
1 2 0.3
kNm
-2100 0.24
-1203 -1353 0.18
-1400
0.12
-700 0.06
0 0
700 -0.06
1400 -0.12
2100 -0.18
0.17
-0.24
2800 2492 0 10600mm
0 10600mm
Neutral Axis Depth Initial Final
Moment Moment 1 Moment 2
Service
1 2 Maximum Moment Condition
kN
900 781 1 2
MPa MPa
600 -9.72
-12 -200
300 -9 -150
0 -6 -100
-300 -3 -50
-600 0 0
-900 3 50
-1200 -994 6 100
0 10600mm 9 150
12 7.18 200
Shear Shear 1 Shear 2 0 10600mm
Gross Stress Top Gross Stress Bottom Cracked Compression Reinforcement Tension Limits
Flexural Design
Ultimate Reversal Moment Condition
1 2 1 2
mm2 MPa MPa
4414
6000 4960 -12 -9.37 -200
4000 -9 -150
2000 -6 -100
0 -3 -50
-2000 0 0
-4000 3 50
-6000 6 100
-8000 9 150
-10000 12 200
9285 7.07
-12000
0 10600mm 0 10600mm
Reinforcement Top Total Bottom Total Top Ultimate Bottom Ultimate Min Top Min Bot Gross Stress Top Gross Stress Bottom Cracked Compression Reinforcement Tension Limits
Span 1
kNm1 2
Design Comments:-
-2400 - Increase in stress from decompression to working exceeds 200MPa in at least one steel layer. Reinforcement has been added to reduce stress change
-1600 below this maximum value. Refer RAPT manual Section T.7.6
-800
0
800
1600
Permanent
2400
3200
1 2
4000
0 10600mm MPa -8.35 MPa
-9 -180
Capacity Minimum Ultimate Design Initial Final -6 -120
-3 -60
0 0
3 60
6 120
9 180
12 6.31 240
0 10600mm
RAPT 6.6.8.0 Project Name: J110 Page 11/15 RAPT 6.6.8.0 Project Name: J110 Page 12/15
Licensee: AECOM Singapore Pte Ltd 1/6/2022 8:22:14 PM License No.: 10479063400712WPN11 Licensee: AECOM Singapore Pte Ltd 1/6/2022 8:22:17 PM License No.: 10479063400712WPN11
Frame Description: G/A.1/8/2 Frame Description: G/A.1/8/2
Reversal Moment Condition
Locat V* Mv* Pv Mdec d Ast bv phi Vuc phi Vut phi Vu Phi Vumax phi VuMin phi Vus Theta Asv/s
1 2
MPa -8.35 MPa
-9 -180 mm kN kNm kN kNm mm mm2 mm kN kN kN kN kN kN #.# mm2/mm
-6 -120 6199 453.51 2492.21 0 0 844 9284.55 750 407.38 99999 407.38 3179.38 560.51 453.51 21.8 0.68
-3 -60 6201 -820.87 2546.79 0 0 844 9283.06 750 407.36 99999 407.36 3179.38 560.51 820.87 21.8 0.99
0 0 7076 -860.33 1835.92 0 0 844 6601.48 750 363.61 99999 363.61 3179.38 560.51 860.33 21.8 1.04
3 60 7950 -905.09 1064.44 0 0 844 3820.81 750 303.02 99999 303.02 3179.38 560.51 905.09 21.8 1.1
6 120 8311 -920.68 752.1 0 0 844 2627.96 750 267.48 99999 267.48 3179.38 560.51 920.68 21.8 1.12
9 180 8672 -939.16 416.39 0 0 844 1459 750 227.21 99999 227.21 3179.38 560.51 939.16 21.8 1.14
12 6.31 240 9033 -957.65 74.02 0 0 844 1201.83 750 227.21 99999 227.21 3179.38 560.51 957.65 21.8 1.16
0 10600mm 9394 -975.28 -268.97 0 0 844 1834.33 750 237.27 99999 237.27 3179.38 560.51 975.28 21.8 1.18
9755 -993.77 -624.38 0 0 844 2208.8 750 252.43 99999 252.43 3179.38 560.51 993.77 21.8 1.2
Gross Stress Top Gross Stress Bottom Cracked Compression Reinforcement Tension Limits 10475 -1030.64 -1353.17 0 0 844 4960.04 750 0 0 0 3179.38 0 0 0
Gross Stress Top Gross Stress Bottom Cracked Compression Reinforcement Tension Limits
Punching
Shear Design Column Head Critical Section
Column Bh a at u d fcv P/A Asw/s min V* Mv* V*eff VRd1 VRd2 Asv result
Beam No.
Span 1 A #.# mm mm mm mm MPa MPa mm2/mm kN kNm kN kN kN mm2 A
Locat V* Mv* Pv Mdec d Ast bv phi Vuc phi Vut phi Vu Phi Vumax phi VuMin phi Vus Theta Asv/s 1 3 0 900 1900 844 0.4 0 0 824.25 1306.08 824.25 640.52 4710.19 1451.41 O K with Ties
2 3 0 900 1900 844 0.4 0 0 1037.04 1482.4 1037.04 639.48 4710.19 1451.41 O K with Ties
-40
0.95 166 332 498 249 3
-60 0.92 170 340 510 255 3
507 0.9 174 348.1 522.1 261.1 3
0 10600mm 0.88 178.5 356.9 535.4 267.7 3
0.86 183.1 366.3 549.4 274.7 3
Total Long Term 0.84 187.3 374.5 561.8 280.9 3
0.83 189.3 378.7 568 284 3
mm1 2 0.78 200.7 401.3 600 301 3
0 0.75 210.7 421.3 600 316 3
0.71 219.7 439.4 600 329.6 3
-20 0.68 231.3 462.6 600 346.9 3 Minimum Steel
0.68 231.3 462.6 600 346.9 3 Minimum Steel
-25.1
0.68 231.3 462.6 600 346.9 3 Minimum Steel
-40
0.68 231.3 462.6 600 346.9 3 Minimum Steel
0.99 157.9 315.9 473.8 236.9 3
-60 1.04 150.7 301.4 452 226 3
422 1.1 143.2 286.5 429.7 214.8 3
0 10600mm 1.12 140.8 281.6 422.4 211.2 3
1.14 138 276.1 414.1 207.1 3
Span 1 1.16 135.4 270.7 406.1 203.1 3
Design Comments:- 1.18 132.9 265.8 398.8 199.4 3
- Total Deflection greater than user defined limit = -25.1mm 1.2 130.4 260.9 391.3 195.7 3
Detailed Reinforcement
RAPT 6.6.8.0 Project Name: J110 Page 15/15
Licensee: AECOM Singapore Pte Ltd 1/6/2022 8:22:28 PM License No.: 10479063400712WPN11
Frame Description: G/A.1/8/2
Design Comments:-
- - Span 1 - Required Bar Size is greater than the Preferred Bar Size. Maintaining the same cover will require slightly more reinforcement than calculated.
RAPT has increased the required reinforcement by the ratio of the effective depths for the 2 bar sizes in the reinforcement layout.
- Span - 1 - Reinforcement added at left support contraflexure point for Offset of Bending Moment Diagram for Shear - 2122.15mm2
- Span - 1 - Reinforcement added at right support contraflexure point for Offset of Bending Moment Diagram for Shear - 2761.86mm2
- Span - 1 - Reinforcement added at left span contraflexure point for Offset of Bending Moment Diagram for Shear - 2134.82mm2
- Span - 1 - Reinforcement added at right span contraflexure point for Offset of Bending Moment Diagram for Shear - 2770.83mm2
Reinforcement Layout
1 2
6-H32
7-H32
mm
0
-200
-400
-600
-800
8-H40
0 10600mm
- - Span 1 - Required Bar Size is greater than the Preferred Bar Size. Maintaining the same cover will require slightly more reinforcement than calculated.
RAPT has increased the required reinforcement by the ratio of the effective depths for the 2 bar sizes in the reinforcement layout.
Design Comments:-
- Span - 1 - Reinforcement added at left span contraflexure point for Offset of Bending Moment Diagram for Shear - 2134.82mm2
- Span - 1 - Reinforcement added at right span contraflexure point for Offset of Bending Moment Diagram for Shear - 2770.83mm2
RAPT 6.6.8.0 Project Name: J110 Page 2/21
Licensee: AECOM Singapore Pte Ltd 1/6/2022 8:08:16 PM License No.: 10479063400712WPN11
Frame Description: G/8/A.1/4-1,G/8/A.1/4-2, G/8/A.1/4-3
Project Name: J110
Frame Description: G/8/A.1/4-1,G/8/A.1/4-2, G/8/A.1/4-3 Column Column Support Transverse Transverse
Designer: SLT Grid Type Column prestress
C:\Users\sujeevanleonard.tham\OneDrive - AECOM\Projects\J110\J110\OneDrive_2021-07-01\12. Southern Reference spacing (P/A)
A List mm MPa
Staircase\Design Files\Str\Beams\G,8,A.1,4-1,G,8,A.1,4-2, G,8,A.1,4-3.rpf
4 4 Knife-Edge 750
Load Cases
Load Load Type Load Definition Live Load Description
Case Deflection Case
Input
General List List Y/N A
Design Code List Singapore - Eurocode 2*SAVED* 1 Self Weight Applied Loads
Material List Singapore - Singapore Eurocode Materials*SAVED* 2 Extra Dead Load Applied Loads
Reinforcement Type List Reinforced 3 Initial Dead Load Applied Loads
Member Type List Beam 4 Live Load Applied Loads Y
Panel Type List Internal
Strip Type List One way - Nominal Width
Column Stiffness List Equivalent Column
Concrete Type List Standard Concrete
1. Self Weight - Line
Load Left End Left end of Load at Right Right end of Load at Description
Concrete - Spanning Members List C32/40MPa
Reference load from left end End load from right
Concrete - Columns List C32/40MPa Column reference reference reference end
Top Reinforcement Cover mm 50 column column column
Bottom Reinforcement Cover mm 50 # mm kN/m # mm kN/m A
Top Reinforcement Axis Depth Limit mm 30 1 1 0 16.88 4 0 16.88
Bottom Reinforcement Axis Depth Limit mm 30 2 1 0 10.5 4 0 10.5 SLAB,200MM THK, 2.1M WIDTH
Concrete Unit Weight kn/m3 25 3 1 0 5 4 0 5 WALL, 250MM THK, 0.8M HT
Self Weight Definition List Program Calculated
Pattern Live Load Y/N Y
Earthquake Design List None
%
2. Extra Dead Load - Line
Moment Redistribution 0
Load Left End Left end of Load Right Right end of Load Description
Design Surface Levels List Extreme Surfaces Reference load from at left End load from at right
Eurocode Ultimate Load Combination Basis List Eurocode Eqn 6.10 Column reference end reference reference end
column column column
# mm kN/m # mm kN/m A
Due to the different Concrete Strength types in the Design Standard and Materials in this run, the concrete strengths shown in the materials data have been 1 1 0 5.3 4 0 5.3 SDL=2.5KPA, 2.1M WIDTH
multiplied in the calculatiuons by 0.8
Load Combinations : Short Term Service Load Case 2 : 2. Extra Dead Load
Load Description 1. Self 2. Extra 3. Initial 4. Live
Combination Weight Dead Load Dead Load Load
A #.# #.# #.# #.# kN/m1 2 3 4
1 Live Load 1 1 1 0.5 20
15
10 L1
5
Load Combinations : Permanent Service 0
0 3100 6700 10700mm
Load Description 1. Self 2. Extra 3. Initial 4. Live
Combination Weight Dead Load Dead Load Load
Load Case 3 : 3. Initial Dead Load
A #.# #.# #.# #.#
1 Live Load 1 1 1 0.3
kN/m1 2 3 4kN
20 800
15 1 600
Load Combinations : Deflection 10 400
Load Description 1. Self 2. Extra 3. Initial 4. Live 5 200
0 0
Combination Weight Dead Load Dead Load Load 0 3100 6700 10700mm
A #.# #.# #.# #.#
1 Short Term - Deflection 1 1 1 0.5 Load Case 4 : 4. Live Load
2 Permanent - Deflection 1 1 1 0.3
3 Initial - Deflection 1 0 1 0
kN/m1 2 3 4kN
20 800
15 600
Load Combinations : Transfer Prestress 10 1 400
5 200
Load Description 1. Self 2. Extra 3. Initial 4. Live 0 0
Combination Weight Dead Load Dead Load Load 0 3100 6700 10700mm
A #.# #.# #.# #.# 20 800
1 Transfer 1 0 0 0 15 L1 600
10 400
5 200
0 0
Load Combinations : Pre Existing 1 2 3 4
Load Description 1. Self 2. Extra 3. Initial 4. Live
Combination Weight Dead Load Dead Load Load Reinforcement
A #.# #.# #.# #.# Reinforcement Reinforcement Preferred Number
1 Pre Existing 1 0 0 0 Use Type Bar Size of Legs
List List #
Flexural Bar H 500MPa
Flexural Mesh A 500MPa
Load Combinations : Construction
Shear Option 1 H 500MPa 10 2
Load Description 1. Self 2. Extra 3. Initial 4. Live
Shear Option 2 H 500MPa 10 4
Combination Weight Dead Load Dead Load Load
A #.# #.# #.# #.# Shear Option 3 H 500MPa 10 6
1 Construction 1 0 0 0 Punching Shear H 500MPa 10 2
Reinforcement
Maximum Minimum Minimum Minimum Span Minimum Span Infill Stagger
Bar Bar Continuous Reinforcement Reinforcement Bars Bars
Spacing Spacing Reinforcement into End into Internal
Support Support
mm mm #.# #.# #.# Y/N Y/N
Support Reinforcement 300 60 0 N N
RAPT 6.6.8.0 Project Name: J110 Page 5/21 RAPT 6.6.8.0 Project Name: J110 Page 6/21
Licensee: AECOM Singapore Pte Ltd 1/6/2022 8:08:28 PM License No.: 10479063400712WPN11 Licensee: AECOM Singapore Pte Ltd 1/6/2022 8:08:32 PM License No.: 10479063400712WPN11
Frame Description: G/8/A.1/4-1,G/8/A.1/4-2, G/8/A.1/4-3 Frame Description: G/8/A.1/4-1,G/8/A.1/4-2, G/8/A.1/4-3
Maximum Minimum Minimum Minimum Span Minimum Span Infill Stagger Include Strain Hardening of Reinforcement Y/N N
Bar Bar Continuous Reinforcement Reinforcement Bars Bars Beam Shear Critical Section Location List Code Critical Section
Spacing Spacing Reinforcement into End into Internal
Support Support
mm mm #.# #.# #.# Y/N Y/N
Span Reinforcement 300 60 0 0 N N Maximum Service Stress Change - Prestressed Sections MPa 150
Maximum Service Stress Change - Reinforced Sections MPa 200
Relative Humidity % 50
Average Temperature C. 20
Design Zones Prestress Losses Calculations based on List Program Default
Layer Steel Left End Distance to Bar stagger Top Right End Distance to Bar stagger Top Cover Maximum Minimum Preferred Crack Width Calculations List .20 mm
Number type Reference left end of length at left Cover at Reference right end of length at right at Right Bar Size Bar Size bar size
AS3600 Shrinkage and Temperature Reinforcement List Moderate
Column bar end left end Column bar end end
List # mm mm mm # mm mm mm List List List Degree of Restraint in Primary Direction % 0
1 Bar 1 0 0 50 4 0 0 50 40 16 25 Degree of Restraint in Secondary Direction % 0
Concrete Strength Gain Rate List N
Layer Minimum Maximum Minimum % in
Number Number of Spacing of Steel area as Flange Concrete Tensile Strength for Deflection Calculations- #.## x (Fc)n #.# -1
Bars Bars % Maximum Value of Ieff/Igross for Deflection Calculations #.# 0.6
# mm % % Total Deflection Warning Limit - Maximum Span/Deflection #.# 250
1 0 0 0 0 Total Deflection Warning Limit - Maximum Deflection mm 25
Incremental Deflection Warning Limit - Maximum Span/Deflection #.# 1000
Incremental Deflection Warning Limit - Maximum Deflection mm 10
Design Zones Initial Time for Shrinkage List Full Shrinkage
Layer Steel Left End Distance to Bar stagger Bottom Right End Distance to Bar stagger Bottom Maximum Minimum Preferred Time of Loading in days #.# 10
Number type Reference left end of length at left Cover at left Reference right end of length at right Cover at Bar Size Bar Size bar size Age Adjustment Factor #.# 0.76
Column bar end end Column bar end Right End Concrete Strength at Time of Loading MPa 27.04
List # mm mm mm # mm mm mm List List List Loaded Period in years #.# 30
1 Bar 1 0 0 50 4 0 0 50 40 16 25 Tension stiffening Approach List Modified Concrete Tensile Modulus Method
Material Properties
Reinforcement Design Zones Concrete : Standard Concrete : Concrete Strength Basis - Cube
Description A C32/40MPa
1 2 3 4
mm Characteristic Compressive Strength MPa 40
0 Mean Compressive Strength MPa 50
Lower Characteristic Tensile Strength MPa 2.12
-200 Upper Characteristic Tensile Strength MPa 3.93
Concrete Density kg/m3 2447
-400
Design Concrete Modulus MPa 31186.6
-600 Mean Concrete Modulus MPa 33345.8
Basic Shrinkage Strain mm/mm 0
-800 Shrinkage Multiplier #.# 1
Basic Creep Factor #.# 2.656
0 3100 6700 10700mm
Creep Multiplier #.# 1
Design Data Concrete Strain at Peak Stress #.# 0.002
Capacity Reduction factor (phi) for Flexure #.# 1 Squash Load Factor #.# 0.85
Capacity Reduction factor (phi) for Shear #.# 1 Concrete Strain Limit #.# 0.004
Capacity Reduction factor (phi) for Shear with transverse reinf #.# 1 Strength Gain Rate List Normal
Material Factor for Concrete in Flexure #.# 1.5 Maximum Aggregate Size mm 20
Material Factor for Concrete in Shear #.# 1.5
Material Factor for Reinforcement #.# 1.15
Maximum Ratio of Neutral Axis Depth for Ductility #.# 0.58
Ductility Limit - Strain #.# 0
Reinforcement Bar
Y/N Designation Type Yield Elastic Ductility Peak Peak Design Material Material Material Capacity Material Capacity Include as Description
Ductility Check at Left End Column Y
Stress Modulus Strain Stress Strain Factor Factor Reduction Factor Reduction Factor Flexural
Ductility Check at Right End Column Y/N Y Limit Flexure Shear - Flexure - Shear Reinforcement for
Minimum Reinforcement Strength Limit - #.## x M* #.# 0 Shear
Flexural Critical Section - Consider Transverse Beams Y/N Y H Deformed 500 2.05e5 N 0.05 540 90 -1 -1 -1 -1 Y
Flexural Critical Section - Distance from centre of Support #.# -1
Beam Left Sideface Cover (Internal) mm 25
Beam Right Sideface cover mm 40 Nominal Bar Bar Area Bar Bar Stock
Prestress Minimum Reinforcement Basis List Program Default Bar Size Diameter Inertia Weight Length
Shear Enhancement at Supports Y/N N A mm mm2 mm4 kg/m mm
Ast Value in Shear Calculations List Calculated 6 6 28.3 63.64 0.22 12000
Limit Reinforcement Strain Y/N Y 8 8 50.3 201.14 0.4 12000
RAPT 6.6.8.0 Project Name: J110 Page 7/21 RAPT 6.6.8.0 Project Name: J110 Page 8/21
Licensee: AECOM Singapore Pte Ltd 1/6/2022 8:08:35 PM License No.: 10479063400712WPN11 Licensee: AECOM Singapore Pte Ltd 1/6/2022 8:08:39 PM License No.: 10479063400712WPN11
Frame Description: G/8/A.1/4-1,G/8/A.1/4-2, G/8/A.1/4-3 Frame Description: G/8/A.1/4-1,G/8/A.1/4-2, G/8/A.1/4-3
Col No. 3 Self Extra Dead Initial Dead Live
Nominal Bar Bar Area Bar Bar Stock Weight Load Load Load
Bar Size Diameter Inertia Weight Length Moment Above kNm -0 -0 -0 -0
A mm mm2 mm4 kg/m mm Moment Below kNm -0 -0 -0 -0
10 10 78.5 491.07 0.62 12000 Reaction kN 141.07 23.09 84.11 87.81
12 13 113.1 1018.29 0.89 12000 Elastic Rotation #.# 0 0 0 0
16 16 201.1 3218.29 1.58 12000 Elastic Axial Shortening mm 0 0 0 0
20 20 314.2 7857.14 2.47 12000
25 25 490.9 19182.5 3.85 12000 Col No. 4 Self Extra Dead Initial Dead Live
32 32 804.2 51492.6 6.31 12000 Weight Load Load Load
40 40 1256.6 1.26e5 9.86 12000 Moment Above kNm -0 -0 -0 -0
50 50 1963.5 3.07e5 15.41 12000 Moment Below kNm -0 -0 -0 -0
Reaction kN 51.94 8.5 -11.72 10.99
Elastic Rotation #.# 0 0 0 0
Elevation view
Elastic Axial Shortening mm 0 0 0 0
1 2 3 4
mm
0
Load Combinations
-200 Column Actions
-400 Col No. 1 Characteristic Characteristic Service Service Ultimate Ultimate Ultimate Ultimate
Service Service (Reversal) Flexure Flexure Shear Shear
-600 (Reversal) (Reversal) (Reversal)
Moment Above kNm 0 0 0 0 0 0 0 0
-800 Moment Below kNm 0 0 0 0 0 0 0 0
Reaction kN 7.69 7.69 9.82 9.82 9.74 9.74 -17.37 39.06
0 3100 6700 10700mm Elastic Rotation #.# 0 0 0 0 0 0 0 0
Elastic Axial Shortening mm 0 0 0 0 0 0 0 0
Plan view
Col No. 2 Characteristic Characteristic Service Service Ultimate Ultimate Ultimate Ultimate
1 2 3 4
Service Service (Reversal) Flexure Flexure Shear Shear
(Reversal) (Reversal) (Reversal)
mm Moment Above kNm 0 0 0 0 0 0 0 0
-200 Moment Below kNm 0 0 0 0 0 0 0 0
Reaction kN 712 712 603.09 603.09 993.87 993.87 517.05 1001.64
0 Elastic Rotation #.# 1.02e-4 1.02e-4 0 0 1.43e-4 1.43e-4 0 1.46e-4
Elastic Axial Shortening mm 0 0 0 0 0 0 0 0
200
Col No. 3 Characteristic Characteristic Service Service Ultimate Ultimate Ultimate Ultimate
Service Service (Reversal) Flexure Flexure Shear Shear
0 3100 6700 10700mm (Reversal) (Reversal) (Reversal)
Warnings Moment Above kNm 0 0 0 0 0 0 0 0
Input Moment Below kNm 0 0 0 0 0 0 0 0
No errors or warnings were found. Reaction kN 336.08 336.08 292.17 292.17 466.87 466.87 286.67 470.64
Elastic Rotation #.# 0 0 0 0 0 0 0 0
Elastic Axial Shortening mm 0 0 0 0 0 0 0 0
Output
No errors or warnings were found.
Col No. 4 Characteristic Characteristic Service Service Ultimate Ultimate Ultimate Ultimate
Service Service (Reversal) Flexure Flexure Shear Shear
(Reversal) (Reversal) (Reversal)
Moment Above kNm 0 0 0 0 0 0 0 0
Moment Below kNm 0 0 0 0 0 0 0 0
Bending Moments
Reaction kN 59.71 59.71 54.21 54.21 82.25 82.25 37.57 93.4
Load Cases
Elastic Rotation #.# 0 0 0 0 0 0 0 0
Column Actions Elastic Axial Shortening mm 0 0 0 0 0 0 0 0
Col No. 1 Self Extra Dead Initial Dead Live
Weight Load Load Load
Moment Above kNm -0 -0 -0 -0
Moment Below kNm -0 -0 -0 -0
Reaction kN 39.73 6.5 -34.28 -4.26
Elastic Rotation #.# 0 0 0 0
Elastic Axial Shortening mm 0 0 0 0
kNm1 2 3 4 1 2 3 4
-400 mm2990 1112 990 0
-294 -294
-300 -206 -206 1200
-200 800
-100 3.57 9.01 400
0 0
100 11.4 -400
65.3
200 -800
300 -1200
400 333 -1600 990 1233 990
0 3100 6700 10700mm 0 3100 6700 10700mm
Moment Moment 1 Moment 2 Reinforcement Top Total Bottom Total Top Ultimate Bottom Ultimate Min Top Min Bot
kN1 2 3 4 1 2 3 4
kNm
1000 -500
746 -400
800
-300
600 -200
400 -100
112 0
200 100
0 200
300
-200 -49.8 -45.4 400
-134 -190
-400 500
600
0 3100 6700 10700mm 0 3100 6700 10700mm
Shear 1 2 3 4
0.056
0.056
0.051
0.051
kNm1 2 3 4 0.06
-400 -294 -294 0.04
-300 -206 -206 0.02
-200 0
-100 3.57 9.01 -0.02
0 -0.04
100 10.5 44.3 -0.06
0.051
0.051
0.06
200
-0.08
300 0 3100 6700 10700mm
400 327
0 3100 6700 10700mm Neutral Axis Depth Initial Final
Moment Moment 1 Moment 2 Span 1
Design Comments:-
- As there is no area of steel in the tension zone (any prestressing tendons are in the compression zone) we are now adding an area of steel, equivalent to
kN1 2 3 4 that required for minimum reinforcement, to the design tension layer. This is then assumed to be the initial design reinforcement setup. More reinforcement will
1000 be added as required to achieve the applied moments. Ast added = 885.05mm2 @ 1033mm
756
800
600 Span 2
400 Design Comments:-
137 - As there is no area of steel in the tension zone (any prestressing tendons are in the compression zone) we are now adding an area of steel, equivalent to
200
0 that required for minimum reinforcement, to the design tension layer. This is then assumed to be the initial design reinforcement setup. More reinforcement will
be added as required to achieve the applied moments. Ast added = 885.05mm2 @ 5800mm
-200 -50.8 -46.1
-151
-400 -238
Span 3
0 3100 6700 10700mm
Design Comments:-
Shear Shear 1 Shear 2 - As there is no area of steel in the tension zone (any prestressing tendons are in the compression zone) we are now adding an area of steel, equivalent to
that required for minimum reinforcement, to the design tension layer. This is then assumed to be the initial design reinforcement setup. More reinforcement will
be added as required to achieve the applied moments. Ast added = 885.05mm2 @ 8033mm
RAPT 6.6.8.0 Project Name: J110 Page 11/21 RAPT 6.6.8.0 Project Name: J110 Page 12/21
Licensee: AECOM Singapore Pte Ltd 1/6/2022 8:08:50 PM License No.: 10479063400712WPN11 Licensee: AECOM Singapore Pte Ltd 1/6/2022 8:08:53 PM License No.: 10479063400712WPN11
Frame Description: G/8/A.1/4-1,G/8/A.1/4-2, G/8/A.1/4-3 Frame Description: G/8/A.1/4-1,G/8/A.1/4-2, G/8/A.1/4-3
Service Reversal Moment Condition
Maximum Moment Condition
1 2 3 4
MPa MPa
MPa1 2 3 4MPa -1.39 -1.47 -1.05
-2 -200
-3 -1.71 -1.88 -1.23 -210
-2 -140 -1 -100
-1 -70 0 0
0 0 1 100
1 70 2 200
2 140 3 300
3 210 4 400
4 280 5 500
1.41 1.48 1.07
5 350
6 1.73 1.9 1.24 420 0 3100 6700 10700mm
0 3100 6700 10700mm
Gross Stress Top Gross Stress Bottom Cracked Compression Reinforcement Tension Limits
Gross Stress Top Gross Stress Bottom Cracked Compression Reinforcement Tension Limits
Gross Stress Top Gross Stress Bottom Cracked Compression Reinforcement Tension Limits
1 2 3 4
MPa -1.57 -1.72 -1.15 MPa
-2 -200 Shear Design
-1 -100 Beam
0 0
Span 1
1 100
Locat V* Mv* Pv Mdec d Ast bv phi Vuc phi Vut phi Vu Phi Vumax phi VuMin phi Vus Theta Asv/s
2 200
3 300
4 400 mm kN kNm kN kNm mm mm2 mm kN kN kN kN kN kN #.# mm2/mm
5 1.6 1.74 1.16 500
100 32.4 3.57 0 0 837.5 989.94 750 0 0 0 3154.9 0 0 0
0 3100 6700 10700mm 720 -50.83 -19.33 0 0 837.5 989.94 750 225.89 99999 225.89 3154.9 556.19 0 21.8 0.68
775 -54.5 -22.23 0 0 837.5 989.94 750 225.89 99999 225.89 3154.9 556.19 0 21.8 0.68
Gross Stress Top Gross Stress Bottom Cracked Compression Reinforcement Tension Limits
1033 -67.91 -34.61 0 0 837.5 989.94 750 225.89 99999 225.89 3154.9 556.19 0 21.8 0.68
1291 -83.07 -54.22 0 0 837.5 989.94 750 225.89 99999 225.89 3154.9 556.19 0 21.8 0.68
1550 -99.45 -74.12 0 0 837.5 989.94 750 225.89 99999 225.89 3154.9 556.19 0 21.8 0.68
1809 -114.6 -98.33 0 0 837.5 989.94 750 225.89 99999 225.89 3154.9 556.19 0 21.8 0.68
2067 -130.43 -127.29 0 0 837.5 989.94 750 225.89 99999 225.89 3154.9 556.19 0 21.8 0.68
2325 -147.61 -163.16 0 0 837.5 989.94 750 225.89 99999 225.89 3154.9 556.19 0 21.8 0.68
2380 -150.54 -169.63 0 0 837.5 989.94 750 225.89 99999 225.89 3154.9 556.19 0 21.8 0.68
3099 -198.22 -294.42 0 0 837.5 1111.64 750 0 0 0 3154.9 0 0 0
RAPT 6.6.8.0 Project Name: J110 Page 13/21 RAPT 6.6.8.0 Project Name: J110 Page 14/21
Licensee: AECOM Singapore Pte Ltd 1/6/2022 8:08:57 PM License No.: 10479063400712WPN11 Licensee: AECOM Singapore Pte Ltd 1/6/2022 8:09:01 PM License No.: 10479063400712WPN11
Frame Description: G/8/A.1/4-1,G/8/A.1/4-2, G/8/A.1/4-3 Frame Description: G/8/A.1/4-1,G/8/A.1/4-2, G/8/A.1/4-3
Spacing of Sets Minimum Legs Shear Comments
2 legs 4 legs 6 legs Min legs Locat V* Mv* Pv Mdec d Ast bv phi Vuc phi Vut phi Vu Phi Vumax phi VuMin phi Vus Theta Asv/s
H10 H10 H10 H10
mm mm mm mm # A
mm kN kNm kN kNm mm mm2 mm kN kN kN kN kN kN #.# mm2/mm
231.3 462.6 600 346.9 3 Minimum Steel 2667 16.13 37.68 0 0 837.5 989.94 750 225.89 99999 225.89 3154.9 556.19 0 21.8 0.68
231.3 462.6 600 346.9 3 Minimum Steel 3000 -29.3 54.73 0 0 837.5 989.94 750 225.89 99999 225.89 3154.9 556.19 0 21.8 0.68
231.3 462.6 600 346.9 3 Minimum Steel 3140 -36.75 54.27 0 0 837.5 989.94 750 225.89 99999 225.89 3154.9 556.19 0 21.8 0.68
231.3 462.6 600 346.9 3 Minimum Steel 3280 -46.07 48.47 0 0 837.5 989.94 750 225.89 99999 225.89 3154.9 556.19 0 21.8 0.68
231.3 462.6 600 346.9 3 Minimum Steel 3900 -86.74 9.01 0 0 837.5 989.94 750 0 0 0 3154.9 0 0 0
231.3 462.6 600 346.9 3 Minimum Steel
231.3 462.6 600 346.9 3 Minimum Steel Spacing of Sets Minimum Legs Shear Comments
231.3 462.6 600 346.9 3 Minimum Steel 2 legs 4 legs 6 legs Min legs
231.3 462.6 600 346.9 3 Minimum Steel H10 H10 H10 H10
mm mm mm mm # A
-1
Span 3 99999 99999 62540
-1.5
Locat V* Mv* Pv Mdec d Ast bv phi Vuc phi Vut phi Vu Phi Vumax phi VuMin phi Vus Theta Asv/s 0 3100 6700 10700mm
0 0
0.064 -0.026 0.069 0.021
-0.17 -0.175
-0.5 -0.5
-1 -1
Even Spans Loaded Odd Spans Loaded All Spans Loaded All Spans Loaded Odd Spans Loaded Even Spans Loaded
Incremental Incremental
1 2 3 4 1 2 3 4
mm mm
0.5 0.5
0 0.142 0 0.147
-0.104 -0.092
-0.5 -0.377 -0.5 -0.383
-1 -1
Even Spans Loaded Odd Spans Loaded All Spans Loaded All Spans Loaded Odd Spans Loaded Even Spans Loaded
1 2 3 4 1 2 3 4
mm mm
0.5 0.5
0 0.194 0 0.199
-0.121 -0.109
-0.5 -0.5
-0.513 -0.518
-1 -1
Even Spans Loaded Odd Spans Loaded All Spans Loaded All Spans Loaded Odd Spans Loaded Even Spans Loaded
0 0
-0.022 0.004 -0.064 -0.022 0.004 -0.064
-0.5 -0.5
-1 -1
1 2 3 4
mm
0.5
0 0.123
0.68 231.3 462.6 600 346.9 3 Minimum Steel
-0.117
-0.5 -0.338 0.68 231.3 462.6 600 346.9 3 Minimum Steel
0.68 231.3 462.6 600 346.9 3 Minimum Steel
-1 0.68 231.3 462.6 600 346.9 3 Minimum Steel
0.68 231.3 462.6 600 346.9 3 Minimum Steel
-1.5 25287 10646 34260 0.68 231.3 462.6 600 346.9 3 Minimum Steel
0 3100 6700 10700mm 0.68 231.3 462.6 600 346.9 3 Minimum Steel
0.68 231.3 462.6 600 346.9 3 Minimum Steel
All Spans Loaded Even Spans Loaded Odd Spans Loaded 0.68 231.3 462.6 600 346.9 3 Minimum Steel
Total Long Term
1 2 3 4
mm
0.5
0 0.175
-0.134
-0.5 Design Comments:-
-0.474
- - Column Grid 1 - Required Bar Size is smaller than the Preferred Bar Size. Maintaining the same cover will require slightly less reinforcement than
-1 calculated.
- - Column Grid 2 - Required Bar Size is smaller than the Preferred Bar Size. Maintaining the same cover will require slightly less reinforcement than
-1.5 17744 7599 29888 calculated.
0 3100 6700 10700mm - - Span 1 - Required Bar Size is smaller than the Preferred Bar Size. Maintaining the same cover will require slightly less reinforcement than calculated.
- Span - 1 - Reinforcement added at left span contraflexure point for Offset of Bending Moment Diagram for Shear - 71.55mm2
All Spans Loaded Even Spans Loaded Odd Spans Loaded - Span - 1 - Reinforcement added at right span contraflexure point for Offset of Bending Moment Diagram for Shear - 71.55mm2
Max Max Section Max Max Section Max Max Section Max Max Section
Locat Size Space Area Depth Width Rebar Reqd Size Space Area Depth Width Rebar Reqd Locat Size Space Area Depth Width Rebar Reqd Size Space Area Depth Width Rebar Reqd
mm mm mm mm2 mm mm A mm mm mm2 mm mm A mm mm mm mm2 mm mm A mm mm mm2 mm mm A
3027 25 300 989.94 62.5 750 4 H20 @ 215 0 0 0 837.5 750 No Steel Added 3590 0 0 0 62.5 750 No Steel Added 25 300 989.94 837.5 750 4 H20 @ 215
3170 25 300 989.94 62.5 750 4 H20 @ 215 0 0 0 837.5 750 No Steel Added 3745 0 0 0 62.5 750 No Steel Added 25 300 989.94 837.5 750 4 H20 @ 215
3313 25 300 989.94 62.5 750 4 H20 @ 215 0 0 0 837.5 750 No Steel Added 3900 0 0 0 62.5 750 No Steel Added 25 300 989.94 837.5 750 4 H20 @ 215
3456 25 300 989.94 62.5 750 4 H20 @ 215 0 0 0 837.5 750 No Steel Added Shear Reinforcement
3599 25 199.9 989.94 62.5 750 4 H20 @ 215 0 0 0 837.5 750 No Steel Added Spacing of Sets
Shear Reinforcement 2 legs 4 legs 6 legs Min legs Minimum Shear
Spacing of Sets Area H10 H10 H10 H10 Legs Comments
2 legs 4 legs 6 legs Min legs Minimum Shear mm2/mm mm mm mm mm # A
Area H10 H10 H10 H10 Legs Comments
mm2/mm mm mm mm mm # A
Design Comments:-
- - Column Grid 3 - Required Bar Size is smaller than the Preferred Bar Size. Maintaining the same cover will require slightly less reinforcement than
calculated.
- - Span 3 - Required Bar Size is smaller than the Preferred Bar Size. Maintaining the same cover will require slightly less reinforcement than calculated.
- Span - 3 - Reinforcement added at left support contraflexure point for Offset of Bending Moment Diagram for Shear - 107.91mm2
Design Comments:-
- Span - 3 - Reinforcement added at left span contraflexure point for Offset of Bending Moment Diagram for Shear - 183.12mm2
- - Column Grid 2 - Required Bar Size is smaller than the Preferred Bar Size. Maintaining the same cover will require slightly less reinforcement than
- Span - 3 - Reinforcement added at right span contraflexure point for Offset of Bending Moment Diagram for Shear - 183.12mm2
calculated.
- - Column Grid 3 - Required Bar Size is smaller than the Preferred Bar Size. Maintaining the same cover will require slightly less reinforcement than
calculated.
- - Span 2 - Required Bar Size is smaller than the Preferred Bar Size. Maintaining the same cover will require slightly less reinforcement than calculated.
- Span - 2 - Reinforcement added at left support contraflexure point for Offset of Bending Moment Diagram for Shear - 126.15mm2 Reinforcement Layout
- Span - 2 - Reinforcement added at right support contraflexure point for Offset of Bending Moment Diagram for Shear - 307.3mm2
1 2 3 4
4-H20
6-H16
4-H20
- Span - 2 - Reinforcement added at left span contraflexure point for Offset of Bending Moment Diagram for Shear - 938.85mm2
mm
- Span - 2 - Reinforcement added at right span contraflexure point for Offset of Bending Moment Diagram for Shear - 684.72mm2
0
Span 3 -200
Top Reinforcement Bottom Reinforcement
-400
Max Max Section Max Max Section -600
Locat Size Space Area Depth Width Rebar Reqd Size Space Area Depth Width Rebar Reqd
mm mm mm mm2 mm mm A mm mm mm2 mm mm A -800
4-H20
7-H16
4-H20
1 16 199.8 989.94 62.5 750 4 H20 @ 215 0 0 0 837.5 750 No Steel Added
144 25 225.5 989.94 62.5 750 4 H20 @ 215 0 0 0 837.5 750 No Steel Added 0 3100 6700 10700mm
287 25 300 989.94 62.5 750 4 H20 @ 215 0 0 0 837.5 750 No Steel Added
430 25 300 989.94 62.5 750 4 H20 @ 215 0 0 0 837.5 750 No Steel Added - - Column Grid 1 - Required Bar Size is smaller than the Preferred Bar Size. Maintaining the same cover will require slightly less reinforcement than
573 25 300 989.94 62.5 750 4 H20 @ 215 0 0 0 837.5 750 No Steel Added calculated.
720 25 300 989.94 62.5 750 4 H20 @ 215 0 0 0 837.5 750 No Steel Added - - Column Grid 2 - Required Bar Size is smaller than the Preferred Bar Size. Maintaining the same cover will require slightly less reinforcement than
860 25 300 989.94 62.5 750 4 H20 @ 215 0 0 442.53 837.5 750 2 H20 @ 645 calculated.
1000 25 300 989.94 62.5 750 4 H20 @ 215 0 0 442.53 837.5 750 2 H20 @ 645 - - Span 1 - Required Bar Size is smaller than the Preferred Bar Size. Maintaining the same cover will require slightly less reinforcement than calculated.
1333 25 300 989.94 62.5 750 4 H20 @ 215 25 300 989.35 837.5 750 4 H20 @ 215 Design Comments:-
1666 0 0 989.35 62.5 750 4 H20 @ 215 25 300 989.94 837.5 750 4 H20 @ 215 - Span - 1 - Reinforcement added at left span contraflexure point for Offset of Bending Moment Diagram for Shear - 71.55mm2
- Span - 1 - Reinforcement added at right span contraflexure point for Offset of Bending Moment Diagram for Shear - 71.55mm2
2000 0 0 989.35 62.5 750 4 H20 @ 215 25 300 989.94 837.5 750 4 H20 @ 215
2334 0 0 0 62.5 750 No Steel Added 25 300 989.94 837.5 750 4 H20 @ 215
2667 0 0 0 62.5 750 No Steel Added 25 300 989.94 837.5 750 4 H20 @ 215
3000 0 0 0 62.5 750 No Steel Added 25 300 989.94 837.5 750 4 H20 @ 215
3140 0 0 0 62.5 750 No Steel Added 25 300 989.94 837.5 750 4 H20 @ 215
3280 0 0 0 62.5 750 No Steel Added 25 300 989.94 837.5 750 4 H20 @ 215
3435 0 0 0 62.5 750 No Steel Added 25 300 989.94 837.5 750 4 H20 @ 215
RAPT 6.6.8.0 Project Name: J110 Page 21/21
Licensee: AECOM Singapore Pte Ltd 1/6/2022 8:09:26 PM License No.: 10479063400712WPN11
Frame Description: G/8/A.1/4-1,G/8/A.1/4-2, G/8/A.1/4-3
- - Column Grid 2 - Required Bar Size is smaller than the Preferred Bar Size. Maintaining the same cover will require slightly less reinforcement than
calculated.
- - Column Grid 3 - Required Bar Size is smaller than the Preferred Bar Size. Maintaining the same cover will require slightly less reinforcement than
calculated.
- - Span 2 - Required Bar Size is smaller than the Preferred Bar Size. Maintaining the same cover will require slightly less reinforcement than calculated.
- Span - 2 - Reinforcement added at left span contraflexure point for Offset of Bending Moment Diagram for Shear - 938.85mm2
- Span - 2 - Reinforcement added at right span contraflexure point for Offset of Bending Moment Diagram for Shear - 684.72mm2
- - Column Grid 3 - Required Bar Size is smaller than the Preferred Bar Size. Maintaining the same cover will require slightly less reinforcement than
calculated.
- - Span 3 - Required Bar Size is smaller than the Preferred Bar Size. Maintaining the same cover will require slightly less reinforcement than calculated.
- Span - 3 - Reinforcement added at left span contraflexure point for Offset of Bending Moment Diagram for Shear - 183.12mm2
- Span - 3 - Reinforcement added at right span contraflexure point for Offset of Bending Moment Diagram for Shear - 183.12mm2
RAPT 6.6.8.0 Project Name: J110 Page 2/18
Licensee: AECOM Singapore Pte Ltd 1/6/2022 7:58:16 PM License No.: 10479063400712WPN11
Frame Description: G/A.3/8/1, G/A.3/8/2
Project Name: J110 Beams
Frame Description: G/A.3/8/1, G/A.3/8/2 Beam Beam Beam Beam Effective
Designer: SLT Number Depth Width Width Flange
C:\Users\sujeevanleonard.tham\OneDrive - AECOM\Projects\J110\J110\OneDrive_2021-07-01\12. Southern at Width
Slab
Staircase\Design Files\Str\Beams\G,8,A.3,8,1, G,8,A.3,8,2 .rpf mm mm mm mm
1 900 750 750 750
RAPT - Version: 6.6.8.0 RC 900 750 750 750
Reinforced And Post-Tensioned Concrete Analysis & Design Package
Copyright(C) 1988 - 2021 PCDC Pty. Ltd. All Rights Reserved
Load Cases
Licensee Load Load Type Load Definition Live Load Description
AECOM Singapore Pte Ltd Case Deflection Case
300 Beach Road
#03-00 The Concourse List List Y/N A
Singapore 199555 1 Self Weight Applied Loads
10479063400712WPN11 2 Extra Dead Load Applied Loads
3 Live Load Applied Loads Y
Due to the different Concrete Strength types in the Design Standard and Materials in this run, the concrete strengths shown in the materials data have been 2. Extra Dead Load - Point
multiplied in the calculatiuons by 0.8 Load Reference Distance to Load Load Description
column Load from Length
Span reference
Span Span Slab Panel Panel column
# mm kN mm A
Length Depth Width Width
Left Right 1 2 900 15 0
mm mm mm mm
LE 0
1 7100 350 4000 4000 3. Live Load - Panel
RC 4800 350 4000 4000 Load Left End Left end of Load at Right Right end of Load at Live Description
reference load from left end End load from right Load
column reference reference reference end reduction
column column column
Columns # mm kN/m2 # mm kN/m2 #.# A
Column Column Support Transverse Transverse
1 1 0 5 2 4800 5 1 LL
Grid Type Column prestress
Reference spacing (P/A)
A List mm MPa
1 1 Knife-Edge 4000
2 2 Knife-Edge 4000
RAPT 6.6.8.0 Project Name: J110 Page 3/18 RAPT 6.6.8.0 Project Name: J110 Page 4/18
Licensee: AECOM Singapore Pte Ltd 1/6/2022 7:58:20 PM License No.: 10479063400712WPN11 Licensee: AECOM Singapore Pte Ltd 1/6/2022 7:58:23 PM License No.: 10479063400712WPN11
Frame Description: G/A.3/8/1, G/A.3/8/2 Frame Description: G/A.3/8/1, G/A.3/8/2
3. Live Load - Point Load Case 1 : 1. Self Weight
Load Reference Distance to Load Load Live Description
column Load from Length Load 1 2
reference reduction kN/m kN
50 100
column 40 1 80
# mm kN mm #.# A 30 60
20 40
1 2 900 25 0 1 10 20
0 0
0 7100mm
50 L1 100
Load Combinations : Ultimate 40 80
30 60
Load Description 1. Self 2. Extra 3. 20 40
Combination Weight Dead Live 10 20
0 0
Load Load
A #.# #.# #.# 1 2
1 Live Load 1.35 1.35 1.5
2 Live Load 1 1 1.5 Load Case 2 : 2. Extra Dead Load
3 Dead Load 1.425 1.425 0
1 2
kN/m kN
50 100
Load Combinations : Short Term Service 40 80
30 60
Load Description 1. Self 2. Extra 3. Live 20 1 40
Combination Weight Dead Load Load 10 20
0 0
A #.# #.# #.# 0 7100mm
1 Live Load 1 1 0.5 50 100
40 80
30 60
20 P1 40
10 20
Load Combinations : Permanent Service 0 0
Load Description 1. Self 2. Extra 3. Live 1 2
Combination Weight Dead Load Load
A #.# #.# #.#
1 Live Load 1 1 0.3
Load Case 3 : 3. Live Load
1 2
kN/m kN
50 100
Load Combinations : Deflection 40 80
Load Description 1. Self 2. Extra 3. Live 30 60
20 1 40
Combination Weight Dead Load Load 10 20
A #.# #.# #.# 0 0
0 7100mm
1 Short Term - Deflection 1 1 0.5
50 100
2 Permanent - Deflection 1 1 0.3 40 80
3 Initial - Deflection 1 0 0 30 P1 60
20 40
10 20
0 0
1 2
Load Combinations : Transfer Prestress
Load Description 1. Self 2. Extra 3. Live Reinforcement
Combination Weight Dead Load Load Reinforcement Reinforcement Preferred Number
A #.# #.# #.# Use Type Bar Size of Legs
1 Transfer 1 0 0 List List #
Flexural Bar H 500MPa
Flexural Mesh A 500MPa
Load Combinations : Pre Existing Shear Option 1 H 500MPa 10 2
Load Description 1. Self 2. Extra 3. Live Shear Option 2 H 500MPa 10 4
Combination Weight Dead Load Load Shear Option 3 H 500MPa 10 6
A #.# #.# #.# Punching Shear H 500MPa 10 2
1 Pre Existing 1 0 0
Reinforcement
Load Combinations : Construction Maximum Minimum Minimum Minimum Span Minimum Span Infill Stagger
Load Description 1. Self 2. Extra 3. Live Bar Bar Continuous Reinforcement Reinforcement Bars Bars
Combination Weight Dead Load Load Spacing Spacing Reinforcement into End into Internal
A #.# #.# #.# Support Support
1 Construction 1 0 0 mm mm #.# #.# #.# Y/N Y/N
Support Reinforcement 300 60 0 N N
Span Reinforcement 300 60 0 0 N N
RAPT 6.6.8.0 Project Name: J110 Page 5/18 RAPT 6.6.8.0 Project Name: J110 Page 6/18
Licensee: AECOM Singapore Pte Ltd 1/6/2022 7:58:27 PM License No.: 10479063400712WPN11 Licensee: AECOM Singapore Pte Ltd 1/6/2022 7:58:30 PM License No.: 10479063400712WPN11
Frame Description: G/A.3/8/1, G/A.3/8/2 Frame Description: G/A.3/8/1, G/A.3/8/2
Design Zones
Layer Steel Left End Distance to Bar stagger Top Right End Distance to Bar stagger Top Cover Maximum Minimum Preferred Crack Width Calculations List .20 mm
Number type Reference left end of length at left Cover at Reference right end of length at right at Right Bar Size Bar Size bar size AS3600 Shrinkage and Temperature Reinforcement List Moderate
Column bar end left end Column bar end end Degree of Restraint in Primary Direction % 0
List # mm mm mm # mm mm mm List List List %
Degree of Restraint in Secondary Direction 0
1 Bar 1 0 0 40 3 0 0 40 40 20 32 Concrete Strength Gain Rate List N
Material Properties
Reinforcement Design Zones Concrete : Standard Concrete : Concrete Strength Basis - Cube
Description A C32/40MPa
1 2 Characteristic Compressive Strength MPa 40
mm
Mean Compressive Strength MPa 50
0
Lower Characteristic Tensile Strength MPa 2.12
-200 Upper Characteristic Tensile Strength MPa 3.93
Concrete Density kg/m3 2447
-400 Design Concrete Modulus MPa 31186.6
-600 Mean Concrete Modulus MPa 33345.8
Basic Shrinkage Strain mm/mm 0
-800 Shrinkage Multiplier #.# 1
Basic Creep Factor #.# 2.656
0 7100mm Creep Multiplier #.# 1
Design Data Concrete Strain at Peak Stress #.# 0.002
Capacity Reduction factor (phi) for Flexure #.# 1 Squash Load Factor #.# 0.85
Capacity Reduction factor (phi) for Shear #.# 1 Concrete Strain Limit #.# 0.004
Capacity Reduction factor (phi) for Shear with transverse reinf #.# 1 Strength Gain Rate List Normal
Material Factor for Concrete in Flexure #.# 1.5 Maximum Aggregate Size mm 20
Material Factor for Concrete in Shear #.# 1.5
Material Factor for Reinforcement #.# 1.15
Maximum Ratio of Neutral Axis Depth for Ductility #.# 0.58 Reinforcement Bar
Ductility Limit - Strain #.# 0 Designation Type Yield Elastic Ductility Peak Peak Design Material Material Material Capacity Material Capacity Include as Description
Ductility Check at Left End Column Y/N Y Stress Modulus Strain Stress Strain Factor Factor Reduction Factor Reduction Factor Flexural
Ductility Check at Right End Column Y/N Y Limit Flexure Shear - Flexure - Shear Reinforcement for
Minimum Reinforcement Strength Limit - #.## x M* #.# 0 Shear
Flexural Critical Section - Consider Transverse Beams Y/N Y H Deformed 500 2.05e5 N 0.05 540 90 -1 -1 -1 -1 Y
Flexural Critical Section - Distance from centre of Support #.# -1
Beam Left Sideface Cover (Internal) mm 25
Beam Right Sideface cover mm 40 Nominal Bar Bar Area Bar Bar Stock
Prestress Minimum Reinforcement Basis List Program Default Bar Size Diameter Inertia Weight Length
Shear Enhancement at Supports Y/N N A mm mm2 mm4 kg/m mm
Ast Value in Shear Calculations List Calculated 10 10 78.5 491.07 0.62 12000
Limit Reinforcement Strain Y/N Y 13 13 132.7 1402.55 1.04 12000
Include Strain Hardening of Reinforcement Y/N N 16 16 201.1 3218.29 1.58 12000
Beam Shear Critical Section Location List Code Critical Section 20 20 314.2 7857.14 2.47 12000
22 22 380.1 11503.6 2.98 12000
25 25 490.9 19182.5 3.85 12000
Maximum Service Stress Change - Prestressed Sections MPa 200 32 32 804.2 51492.6 6.31 12000
Maximum Service Stress Change - Reinforced Sections MPa 200 40 40 1256.6 1.257e5 9.86 12000
Relative Humidity % 50
Average Temperature C. 20
Prestress Losses Calculations based on List Program Default
RAPT 6.6.8.0 Project Name: J110 Page 7/18 RAPT 6.6.8.0 Project Name: J110 Page 8/18
Licensee: AECOM Singapore Pte Ltd 1/6/2022 7:58:33 PM License No.: 10479063400712WPN11 Licensee: AECOM Singapore Pte Ltd 1/6/2022 7:58:37 PM License No.: 10479063400712WPN11
Frame Description: G/A.3/8/1, G/A.3/8/2 Frame Description: G/A.3/8/1, G/A.3/8/2
Elevation view Col No. 2 Characteristic Characteristic Service Service Ultimate Ultimate Ultimate Ultimate
Service Service (Reversal) Flexure Flexure Shear Shear
1 2 (Reversal) (Reversal) (Reversal)
mm Moment Above kNm 0 0 0 0 0 0 0 0
0 Moment Below kNm 0 0 0 0 0 0 0 0
Reaction kN 875 875 761.19 761.19 1215.39 1215.39 753.88 1215.39
-200
Elastic Rotation #.# 7.66e-4 7.66e-4 6.68e-4 6.68e-4 1.06e-3 1.06e-3 2.74e-4 1.06e-3
-400 Elastic Axial Shortening mm 0 0 0 0 0 0 0 0
-600
Load Combinations
Column Actions
Col No. 1 Characteristic Characteristic Service Service Ultimate Ultimate Ultimate Ultimate
Service Service (Reversal) Flexure Flexure Shear Shear
(Reversal) (Reversal) (Reversal)
Moment Above kNm 0 0 0 0 0 0 0 0
Moment Below kNm 0 0 0 0 0 0 0 0
Reaction kN 131.22 131.22 113.53 113.53 182.45 182.45 42.41 235.88
Elastic Rotation #.# 0 0 0 0 0 0 -3.08e-4 2.77e-4
Elastic Axial Shortening mm 0 0 0 0 0 0 0 0
RAPT 6.6.8.0 Project Name: J110 Page 9/18 RAPT 6.6.8.0 Project Name: J110 Page 10/18
Licensee: AECOM Singapore Pte Ltd 1/6/2022 7:58:40 PM License No.: 10479063400712WPN11 Licensee: AECOM Singapore Pte Ltd 1/6/2022 7:58:44 PM License No.: 10479063400712WPN11
Frame Description: G/A.3/8/1, G/A.3/8/2 Frame Description: G/A.3/8/1, G/A.3/8/2
Service
1 2
kN Maximum Moment Condition
800 579
600 1 2
400 MPa MPa
161 -9 -7.51 -7.51 -180
200
-6 -120
0
-3 -60
-200
0 0
-400
3 60
-600 -485 6 120
-800
0 7100mm 9 180
12 240
7.94 7.94
Shear Shear 1 Shear 2
0 7100mm
Flexural Design Gross Stress Top Gross Stress Bottom Cracked Compression Reinforcement Tension Limits
Ultimate Reversal Moment Condition
1 2
1 2
mm2
MPa MPa
60000 5517
-6.16 -6.16
-9 -180
5000
-6 -120
4000
-3 -60
3000
0 0
2000
1000 3 60
0 6 120
-1000 9 180
-2000 982 0 12 240
6.65 6.65
0 7100mm
0 7100mm
Reinforcement Top Total Bottom Total Top Ultimate Bottom Ultimate Min Top Min Bot Gross Stress Top Gross Stress Bottom Cracked Compression Reinforcement Tension Limits
1 2 Span 1
kNm Design Comments:-
-2000 - Increase in stress from decompression to working exceeds 200MPa in at least one steel layer. Reinforcement has been added to reduce stress change
-1600 below this maximum value. Refer RAPT manual Section T.7.6
-1200
-800 Span 2
-400 Design Comments:-
0 - Increase in stress from decompression to working exceeds 200MPa in at least one steel layer. Reinforcement has been added to reduce stress change
below this maximum value. Refer RAPT manual Section T.7.6
400
0 7100mm
MPa MPa
0.3 -9 -6.81 -6.81 -180
0.25 -6 -120
0.2 -3 -60
0.15
0 0
0.1
3 60
0.05
0 6 120
-0.05 9 180
0.051
Neutral Axis Depth Initial Final Gross Stress Top Gross Stress Bottom Cracked Compression Reinforcement Tension Limits
Span 1
Design Comments:-
- As there is no area of steel in the tension zone (any prestressing tendons are in the compression zone) we are now adding an area of steel, equivalent to
that required for minimum reinforcement, to the design tension layer. This is then assumed to be the initial design reinforcement setup. More reinforcement will
be added as required to achieve the applied moments. Ast added = 878.24mm2 @ 2366mm
RAPT 6.6.8.0 Project Name: J110 Page 11/18 RAPT 6.6.8.0 Project Name: J110 Page 12/18
Licensee: AECOM Singapore Pte Ltd 1/6/2022 7:58:50 PM License No.: 10479063400712WPN11 Licensee: AECOM Singapore Pte Ltd 1/6/2022 7:58:54 PM License No.: 10479063400712WPN11
Frame Description: G/A.3/8/1, G/A.3/8/2 Frame Description: G/A.3/8/1, G/A.3/8/2
Reversal Moment Condition
Locat V* Mv* Pv Mdec d Ast bv phi Vuc phi Vut phi Vu Phi Vumax phi VuMin phi Vus Theta Asv/s
1 2
MPa MPa
-9 -6.16 -6.16 -180
mm kN kNm kN kNm mm mm2 mm kN kN kN kN kN kN #.# mm2/mm
-6 -120
6380 -485.35 -966.26 0 0 844 4067.7 750 309.41 99999 309.41 3179.38 560.51 485.35 21.8 0.68
-3 -60 7099 -560.61 -1342.28 0 0 844 5516.76 750 0 0 0 3179.38 0 0 0
0 0
3 60 Spacing of Sets Minimum Legs Shear Comments
6 120 2 legs 4 legs 6 legs Min legs
9 180 H10 H10 H10 H10
12 6.65 6.65 240 mm mm mm mm # A
0 7100mm
231.3 462.6 600 346.9 3 Minimum Steel
Gross Stress Top Gross Stress Bottom Cracked Compression Reinforcement Tension Limits 231.3 462.6 600 346.9 3 Minimum Steel
231.3 462.6 600 346.9 3 Minimum Steel
231.3 462.6 600 346.9 3 Minimum Steel
Characteristic Service
231.3 462.6 600 346.9 3 Minimum Steel
Maximum Moment Condition 231.3 462.6 600 346.9 3 Minimum Steel
231.3 462.6 600 346.9 3 Minimum Steel
1 2
MPa MPa 231.3 462.6 600 346.9 3 Minimum Steel
-12 -8.65 -8.64 -300 231.3 462.6 600 346.9 3 Minimum Steel
-8 -200 231.3 462.6 600 346.9 3 Minimum Steel
-4 -100 231.3 462.6 600 346.9 3 Minimum Steel
0 0 231.3 462.6 600 346.9 3 Minimum Steel
4 100 231.3 462.6 600 346.9 3 Minimum Steel
8 200 231.3 462.6 600 346.9 3 Minimum Steel
12 300
16 9.14 9.14 400
0 7100mm
Span 2
Gross Stress Top Gross Stress Bottom Cracked Compression Reinforcement Tension Limits Locat V* Mv* Pv Mdec d Ast bv phi Vuc phi Vut phi Vu Phi Vumax phi VuMin phi Vus Theta Asv/s
-90
Deflections 2277 133
All Spans Loaded 0 7100mm
Transfer
Even Spans Loaded Odd Spans Loaded All Spans Loaded
1 2
mm Span 2
0 Design Comments:-
0.819 - Incremental Deflection greater than user defined limit = -26.2mm
-10.4
-30
-60
Even Spans Loaded
Transfer
-90
8670 462 1 2
0 7100mm mm
0
Short Term 0.819
-10.4
-30
1 2
mm
0 -60
1.48
-30 -17.8 -90
8670 462
-60 0 7100mm
Short Term
-90
4785 269 1 2
0 7100mm mm
0
Even Spans Loaded Odd Spans Loaded All Spans Loaded 2.04
-30 -19.6
Incremental
1 2 -60
mm
0 -90
2.36
3483 245
-30 0 7100mm
-26.2
-60 All Spans Loaded Odd Spans Loaded Even Spans Loaded
Incremental
-90
3007 183 1 2
0 7100mm mm
0
Even Spans Loaded Odd Spans Loaded All Spans Loaded 2.91
-30
-27.9
-60
-90
2440 172
0 7100mm
-90 -90
1936 127 3007 157
0 7100mm 0 7100mm
All Spans Loaded Odd Spans Loaded Even Spans Loaded All Spans Loaded Even Spans Loaded Odd Spans Loaded
Span 2
Design Comments:-
Detailed Reinforcement
- Incremental Span/Deflection ratio less than user defined limit = 172 Span 1
- Incremental Deflection greater than user defined limit = -27.9mm Top Reinforcement Bottom Reinforcement
Span 2
Top Reinforcement Bottom Reinforcement
Reinforcement Layout
1 2
7-H32
mm
0
-200
-400
-600
-800
4-H20
0 7100mm
RAPT 6.6.8.0 Project Name: J110 Page 2/14
Licensee: AECOM Singapore Pte Ltd 1/6/2022 7:54:12 PM License No.: 10479063400712WPN11
Frame Description: G/8/B/1
Project Name: J110 Column Punching
Frame Description: G/8/B/1 Shear Check
required
Designer: SLT Y/N
C:\Users\sujeevanleonard.tham\OneDrive - AECOM\Projects\J110\J110\OneDrive_2021-07-01\12. Southern 1 N
Staircase\Design Files\Str\Beams\G,8,B,1.rpf 2 N
Reinforcement
Reinforcement Reinforcement Preferred Number
Load Combinations : Transfer Prestress Use Type Bar Size of Legs
Load Description 1. Self 2. Extra 3. Live List List #
Combination Weight Dead Load Load Flexural Bar H 500MPa
A #.# #.# #.#
Flexural Mesh A 500MPa
1 Transfer 1 0 0 Shear Option 1 H 500MPa 10 2
Shear Option 2 H 500MPa 10 4
Shear Option 3 H 500MPa 10 6
Load Combinations : Pre Existing Punching Shear H 500MPa 10 2
Load Description 1. Self 2. Extra 3. Live
Combination Weight Dead Load Load
A #.# #.# #.#
1 Pre Existing 1 0 0
Reinforcement
Maximum Minimum Minimum Minimum Span Minimum Span Infill Stagger
Bar Bar Continuous Reinforcement Reinforcement Bars Bars
Spacing Spacing Reinforcement into End into Internal
Support Support
mm mm #.# #.# #.# Y/N Y/N
Support Reinforcement 300 60 0 N N
RAPT 6.6.8.0 Project Name: J110 Page 5/14 RAPT 6.6.8.0 Project Name: J110 Page 6/14
Licensee: AECOM Singapore Pte Ltd 1/6/2022 7:54:23 PM License No.: 10479063400712WPN11 Licensee: AECOM Singapore Pte Ltd 1/6/2022 7:54:26 PM License No.: 10479063400712WPN11
Frame Description: G/8/B/1 Frame Description: G/8/B/1
Maximum Minimum Minimum Minimum Span Minimum Span Infill Stagger Include Strain Hardening of Reinforcement Y/N N
Bar Bar Continuous Reinforcement Reinforcement Bars Bars Beam Shear Critical Section Location List Code Critical Section
Spacing Spacing Reinforcement into End into Internal
Support Support
mm mm #.# #.# #.# Y/N Y/N
Span Reinforcement 300 60 0 0 N N Maximum Service Stress Change - Prestressed Sections MPa 200
Maximum Service Stress Change - Reinforced Sections MPa 200
Relative Humidity % 50
Average Temperature C. 20
Design Zones Prestress Losses Calculations based on List Program Default
Layer Steel Left End Distance to Bar stagger Top Right End Distance to Bar stagger Top Cover Maximum Minimum Preferred Crack Width Calculations List .20 mm
Number type Reference left end of length at left Cover at Reference right end of length at right at Right Bar Size Bar Size bar size
AS3600 Shrinkage and Temperature Reinforcement List Moderate
Column bar end left end Column bar end end
List # mm mm mm # mm mm mm List List List Degree of Restraint in Primary Direction % 0
1 Bar 1 0 0 40 2 0 0 40 40 20 32 Degree of Restraint in Secondary Direction % 0
Concrete Strength Gain Rate List N
Layer Minimum Maximum Minimum % in
Number Number of Spacing of Steel area as Flange Concrete Tensile Strength for Deflection Calculations- #.## x (Fc)n #.# -1
Bars Bars % Maximum Value of Ieff/Igross for Deflection Calculations #.# 0.6
# mm % % Total Deflection Warning Limit - Maximum Span/Deflection #.# 250
1 0 0 0 0 Total Deflection Warning Limit - Maximum Deflection mm 40
Incremental Deflection Warning Limit - Maximum Span/Deflection #.# 360
Incremental Deflection Warning Limit - Maximum Deflection mm 25
Design Zones Initial Time for Shrinkage List Full Shrinkage
Layer Steel Left End Distance to Bar stagger Bottom Right End Distance to Bar stagger Bottom Maximum Minimum Preferred Time of Loading in days #.# 10
Number type Reference left end of length at left Cover at left Reference right end of length at right Cover at Bar Size Bar Size bar size Age Adjustment Factor #.# 0.76
Column bar end end Column bar end Right End Concrete Strength at Time of Loading MPa 27.04
List # mm mm mm # mm mm mm List List List Loaded Period in years #.# 30
1 Bar 1 0 0 40 2 0 0 40 40 20 32 Tension stiffening Approach List Modified Concrete Tensile Modulus Method
Material Properties
Reinforcement Design Zones Concrete : Standard Concrete : Concrete Strength Basis - Cube
Description A C32/40MPa
1 2
Characteristic Compressive Strength MPa 40
mm
0 Mean Compressive Strength MPa 50
Lower Characteristic Tensile Strength MPa 2.12
-200 Upper Characteristic Tensile Strength MPa 3.93
Concrete Density kg/m3 2447
-400 MPa
Design Concrete Modulus 31186.6
-600 Mean Concrete Modulus MPa 33345.8
Basic Shrinkage Strain mm/mm 0
-800 Shrinkage Multiplier #.# 1
Basic Creep Factor #.# 2.656
0 8900mm
Creep Multiplier #.# 1
Design Data Concrete Strain at Peak Stress #.# 0.002
Capacity Reduction factor (phi) for Flexure #.# 1 Squash Load Factor #.# 0.85
Capacity Reduction factor (phi) for Shear #.# 1 Concrete Strain Limit #.# 0.004
Capacity Reduction factor (phi) for Shear with transverse reinf #.# 1 Strength Gain Rate List Normal
Material Factor for Concrete in Flexure #.# 1.5 Maximum Aggregate Size mm 20
Material Factor for Concrete in Shear #.# 1.5
Material Factor for Reinforcement #.# 1.15
Maximum Ratio of Neutral Axis Depth for Ductility #.# 0.58
Ductility Limit - Strain #.# 0
Reinforcement Bar
Y/N Designation Type Yield Elastic Ductility Peak Peak Design Material Material Material Capacity Material Capacity Include as Description
Ductility Check at Left End Column Y
Stress Modulus Strain Stress Strain Factor Factor Reduction Factor Reduction Factor Flexural
Ductility Check at Right End Column Y/N Y Limit Flexure Shear - Flexure - Shear Reinforcement for
Minimum Reinforcement Strength Limit - #.## x M* #.# 0 Shear
Flexural Critical Section - Consider Transverse Beams Y/N Y H Deformed 500 2.05e5 N 0.05 540 90 -1 -1 -1 -1 Y
Flexural Critical Section - Distance from centre of Support #.# -1
Beam Left Sideface Cover (Internal) mm 25
Beam Right Sideface cover mm 40 Nominal Bar Bar Area Bar Bar Stock
Prestress Minimum Reinforcement Basis List Program Default Bar Size Diameter Inertia Weight Length
Shear Enhancement at Supports Y/N N A mm mm2 mm4 kg/m mm
Ast Value in Shear Calculations List Calculated 10 10 78.5 491.07 0.62 12000
Limit Reinforcement Strain Y/N Y 13 13 132.7 1402.55 1.04 12000
RAPT 6.6.8.0 Project Name: J110 Page 7/14 RAPT 6.6.8.0 Project Name: J110 Page 8/14
Licensee: AECOM Singapore Pte Ltd 1/6/2022 7:54:29 PM License No.: 10479063400712WPN11 Licensee: AECOM Singapore Pte Ltd 1/6/2022 7:54:34 PM License No.: 10479063400712WPN11
Frame Description: G/8/B/1 Frame Description: G/8/B/1
Nominal Bar Bar Area Bar Bar Stock Col No. 1 Self Extra Dead Live
Bar Size Diameter Inertia Weight Length Weight Load Load
A mm mm2 mm4 kg/m mm Elastic Rotation #.# 6.21e-4 1.64e-4 2.82e-4
16 16 201.1 3218.29 1.58 12000 Elastic Axial Shortening mm -0 -0 -0
20 20 314.2 7857.14 2.47 12000
22 22 380.1 11503.6 2.98 12000 Col No. 2 Self Extra Live Load
25 25 490.9 19182.5 3.85 12000 Weight Dead
32 32 804.2 51492.6 6.31 12000 Load
40 40 1256.6 1.257e5 9.86 12000 Moment Above kNm 0 0 0
Moment Below kNm 0 0 0
Reaction kN 177.47 44.09 78.07
Elevation view
Elastic Rotation #.# -6.22e-4 -1.65e-4 -2.83e-4
1 2 Elastic Axial Shortening mm -0 -0 -0
mm
0
mm 1 2
Col No. 2 Characteristic Characteristic Service Service Ultimate Ultimate Ultimate Ultimate
-0
Service Service (Reversal) Flexure Flexure Shear Shear
(Reversal) (Reversal) (Reversal)
600 Moment Above kNm 0 0 0 0 0 0 0 0
Moment Below kNm 0 0 0 0 0 0 0 0
1200 Reaction kN 299.63 299.63 260.6 260.6 416.22 416.22 315.72 416.22
Elastic Rotation #.# -1.07e-3 -1.07e-3 -9.28e-4 -9.28e-4 -1.49e-3 -1.49e-3 -1.12e-3 -1.49e-3
1800 Elastic Axial Shortening mm -0 -0 -0 -0 -0 -0 -0 -0
2400
0 8900mm
Ultimate Design
Full Elevation View Flexure
mm 1 2 kNm1 2
3000 -200
51.2 51.5
0
2000 200
400
1000
600
0 800
1000
-1000 1200 1026
0 8900mm 0 8900mm
Warnings
Input Moment Moment 1 Moment 2
No errors or warnings were found.
1 2
Output kN
500 353
No errors or warnings were found. 400
300
200
100
0
-100
Bending Moments -200
Load Cases -300
-400
Column Actions -500 -355
Col No. 1 Self Extra Dead Live 0 8900mm
Weight Load Load
Moment Above kNm 0 0 0 Shear Shear 1 Shear 2
Moment Below kNm 0 0 0
Reaction kN 176.79 43.76 77.63
RAPT 6.6.8.0 Project Name: J110 Page 9/14 RAPT 6.6.8.0 Project Name: J110 Page 10/14
Licensee: AECOM Singapore Pte Ltd 1/6/2022 7:54:37 PM License No.: 10479063400712WPN11 Licensee: AECOM Singapore Pte Ltd 1/6/2022 7:54:41 PM License No.: 10479063400712WPN11
Frame Description: G/8/B/1 Frame Description: G/8/B/1
Shear
1 2
kNm1 2 0.02
-200 0
51.2 51.5
0 -0.02
200 -0.04
400 -0.06
600 -0.08
800 -0.1
0.103
1000 880 -0.12
0 8900mm
1200
0 8900mm
Neutral Axis Depth Initial Final
Moment Moment 1 Moment 2
Service
1 2 Maximum Moment Condition
kN
500 353 1 2
400
300 MPa MPa
-6 -5.12 -180
200
100 -4 -120
0
-100 -2 -60
-200 0 0
-300 2 60
-400
-500 -355 4 120
0 8900mm 6 180
8 3.94 240
Shear Shear 1 Shear 2 0 8900mm
Gross Stress Top Gross Stress Bottom Cracked Compression Reinforcement Tension Limits
Flexural Design
Ultimate Reversal Moment Condition
1 2 1 2
mm2 MPa MPa
16000 0 -6 -4.99 -180
800 -4 -120
0 -2 -60
-800
0 0
-1600
2 60
-2400
-3200 4 120
-4000 6 180
-4800 4058 8 3.89 240
0 8900mm 0 8900mm
Reinforcement Top Total Bottom Total Top Ultimate Bottom Ultimate Min Top Min Bot Gross Stress Top Gross Stress Bottom Cracked Compression Reinforcement Tension Limits
Span 1
1 2
kNm Design Comments:-
-200 - Increase in stress from decompression to working exceeds 200MPa in at least one steel layer. Reinforcement has been added to reduce stress change
0 below this maximum value. Refer RAPT manual Section T.7.6
200
400
600
800 Permanent
1000
1200
1400
1600 1 2
MPa MPa
0 8900mm -6 -4.68 -180
Capacity Minimum Ultimate Design Initial Final -4 -120
-2 -60
0 0
2 60
4 120
6 180
8 3.65 240
0 8900mm
RAPT 6.6.8.0 Project Name: J110 Page 11/14 RAPT 6.6.8.0 Project Name: J110 Page 12/14
Licensee: AECOM Singapore Pte Ltd 1/6/2022 7:54:45 PM License No.: 10479063400712WPN11 Licensee: AECOM Singapore Pte Ltd 1/6/2022 7:54:48 PM License No.: 10479063400712WPN11
Frame Description: G/8/B/1 Frame Description: G/8/B/1
Reversal Moment Condition
Locat V* Mv* Pv Mdec d Ast bv phi Vuc phi Vut phi Vu Phi Vumax phi VuMin phi Vus Theta Asv/s
1 2
MPa MPa
-6 -4.68 -180
mm kN kNm kN kNm mm mm2 mm kN kN kN kN kN kN #.# mm2/mm
-4 -120 6138 -220.26 838.2 0 0 844 3430.29 750 292.32 99999 292.32 3179.38 560.51 0 21.8 0.68
-2 -60 6675 -259.42 709.41 0 0 844 2897.68 750 276.33 99999 276.33 3179.38 560.51 0 21.8 0.68
0 0 7020 -280.5 644.12 0 0 844 2531.49 750 264.17 99999 264.17 3179.38 560.51 280.5 21.8 0.68
2 60 7365 -305.66 543.01 0 0 844 2133.48 750 249.52 99999 249.52 3179.38 560.51 305.66 21.8 0.68
4 120 7710 -330.81 433.22 0 0 844 1706.01 750 231.6 99999 231.6 3179.38 560.51 330.81 21.8 0.68
6 180 8055 -354.61 325.67 0 0 844 1249.11 750 227.21 99999 227.21 3179.38 560.51 354.61 21.8 0.68
8 3.65 240 8775 -407.1 51.46 0 0 844 1123.85 750 0 0 0 3179.38 0 0 0
0 8900mm
Spacing of Sets Minimum Legs Shear Comments
Gross Stress Top Gross Stress Bottom Cracked Compression Reinforcement Tension Limits 2 legs 4 legs 6 legs Min legs
H10 H10 H10 H10
mm mm mm mm # A
Characteristic Service
Maximum Moment Condition 231.3 462.6 600 346.9 3 Minimum Steel
231.3 462.6 600 346.9 3 Minimum Steel
1 2
MPa MPa 231.3 462.6 600 346.9 3 Minimum Steel
-8 -5.91 -320 231.3 462.6 600 346.9 3 Minimum Steel
-6 -240 231.3 462.6 600 346.9 3 Minimum Steel
-4 -160
-2 -80 231.3 462.6 600 346.9 3 Minimum Steel
0 0 231.3 462.6 600 346.9 3 Minimum Steel
2 80 231.3 462.6 600 346.9 3 Minimum Steel
4 160 231.3 462.6 600 346.9 3 Minimum Steel
6 240
231.3 462.6 600 346.9 3 Minimum Steel
8 320
10 400 231.3 462.6 600 346.9 3 Minimum Steel
4.54
231.3 462.6 600 346.9 3 Minimum Steel
0 8900mm
231.3 462.6 600 346.9 3 Minimum Steel
Gross Stress Top Gross Stress Bottom Cracked Compression Reinforcement Tension Limits 231.3 462.6 600 346.9 3 Minimum Steel
231.3 462.6 600 346.9 3 Minimum Steel
Reversal Moment Condition 231.3 462.6 600 346.9 3 Minimum Steel
231.3 462.6 600 346.9 3 Minimum Steel
1 2 231.3 462.6 600 346.9 3 Minimum Steel
MPa MPa
-8 -5.75 -320 231.3 462.6 600 346.9 3 Minimum Steel
-6 -240
-4 -160
-2 -80
0 0
2 80
4 160
6 240 Punching
8 320 Column Head Critical Section
10 4.48 400 Column Bh a at u d fcv P/A Asw/s min V* Mv* V*eff VRd1 VRd2 Asv result
0 8900mm No.
A #.# mm mm mm mm MPa MPa mm2/mm kN kNm kN kN kN mm2 A
Gross Stress Top Gross Stress Bottom Cracked Compression Reinforcement Tension Limits 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Check Not Requested!
2 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Check Not Requested!
Shear Design
Beam
Span 1
Locat V* Mv* Pv Mdec d Ast bv phi Vuc phi Vut phi Vu Phi Vumax phi VuMin phi Vus Theta Asv/s Deflections
All Spans Loaded
mm kN kNm kN kNm mm mm2 mm kN kN kN kN kN kN #.# mm2/mm
125 405.06 51.2 0 0 844 1123.85 750 0 0 0 3179.38 0 0 0
mm1 2
845 352.57 323.95 0 0 844 1242.71 750 227.21 99999 227.21 3179.38 560.51 352.57 21.8 0.68 0
1190 328.77 430.79 0 0 844 1696.85 750 231.19 99999 231.19 3179.38 560.51 328.77 21.8 0.68
1535 303.62 539.88 0 0 844 2121.48 750 249.06 99999 249.06 3179.38 560.51 303.62 21.8 0.68 -10 -5.07
1880 278.46 640.29 0 0 844 2516.68 750 263.65 99999 263.65 3179.38 560.51 278.46 21.8 0.68
-20
2225 257.38 704.87 0 0 844 2880.04 750 275.77 99999 275.77 3179.38 560.51 0 21.8 0.68
2812 214.58 843.39 0 0 844 3450.67 750 292.9 99999 292.9 3179.38 560.51 0 21.8 0.68 -30
3399 178.56 919.49 0 0 844 3895.63 750 304.98 99999 304.98 3179.38 560.51 0 21.8 0.68
3401 99.13 856.74 0 0 844 3896.61 750 305.01 99999 305.01 3179.38 560.51 0 21.8 0.68 -40
3925 60.92 898.67 0 0 844 4018.68 750 308.16 99999 308.16 3179.38 560.51 0 21.8 0.68 1756
-50
4450 -33.84 879.87 0 0 844 4058.09 750 309.17 99999 309.17 3179.38 560.51 0 21.8 0.68 0 8900mm
5025 -66.27 896.05 0 0 844 4005.94 750 307.84 99999 307.84 3179.38 560.51 0 21.8 0.68
5599 -107.41 846.02 0 0 844 3854.67 750 303.91 99999 303.91 3179.38 560.51 0 21.8 0.68
5601 -187.14 908.01 0 0 844 3853.61 750 303.88 99999 303.88 3179.38 560.51 0 21.8 0.68
RAPT 6.6.8.0 Project Name: J110 Page 13/14 RAPT 6.6.8.0 Project Name: J110 Page 14/14
Licensee: AECOM Singapore Pte Ltd 1/6/2022 7:54:52 PM License No.: 10479063400712WPN11 Licensee: AECOM Singapore Pte Ltd 1/6/2022 7:54:55 PM License No.: 10479063400712WPN11
Frame Description: G/8/B/1 Frame Description: G/8/B/1
Short Term Top Reinforcement Bottom Reinforcement
-20 -17.3
-30 Design Comments:-
- Span - 1 - Reinforcement added at left span contraflexure point for Offset of Bending Moment Diagram for Shear - 1190.63mm2
-40 - Span - 1 - Reinforcement added at right span contraflexure point for Offset of Bending Moment Diagram for Shear - 1196.5mm2
-50 513
0 8900mm
Reinforcement Layout
Detailed Reinforcement
Span 1 1 2
mm
Top Reinforcement Bottom Reinforcement
0
6-H32
1190 0 0 0 56 1373 No Steel Added 16 150.9 2171.12 844 750 3 H32 @ 316.5
1535 0 0 0 56 1373 No Steel Added 16 150.6 2406.92 844 750 3 H32 @ 316.5 0 8900mm
1880 0 0 0 56 1373 No Steel Added 16 150.5 2620.63 844 750 4 H32 @ 211
2225 0 0 0 56 1373 No Steel Added 16 150.5 2880.04 844 750 4 H32 @ 211
2812 0 0 0 56 1373 No Steel Added 16 150.6 3450.67 844 750 5 H32 @ 158.3
3399 0 0 0 56 1373 No Steel Added 16 150.6 3895.63 844 750 5 H32 @ 158.3
3401 0 0 0 56 1373 No Steel Added 16 150.6 3896.61 844 750 5 H32 @ 158.3
3925 0 0 0 56 1373 No Steel Added 16 150.6 4018.68 844 750 5 H32 @ 158.3
4450 0 0 0 56 1373 No Steel Added 16 150.6 4058.09 844 750 6 H32 @ 126.6
5025 0 0 0 56 1373 No Steel Added 16 150.6 4005.94 844 750 5 H32 @ 158.3
5599 0 0 0 56 1373 No Steel Added 16 150.6 3854.67 844 750 5 H32 @ 158.3
5601 0 0 0 56 1373 No Steel Added 16 150.6 3853.61 844 750 5 H32 @ 158.3
6138 0 0 0 56 1373 No Steel Added 16 150.6 3430.29 844 750 5 H32 @ 158.3
6675 0 0 0 56 1373 No Steel Added 16 150.5 2897.68 844 750 4 H32 @ 211
7020 0 0 0 56 1373 No Steel Added 16 150.5 2637.51 844 750 4 H32 @ 211
7365 0 0 0 56 1373 No Steel Added 16 150.6 2421.7 844 750 4 H32 @ 211
7710 0 0 0 56 1373 No Steel Added 16 150.9 2183.84 844 750 3 H32 @ 316.5
8055 0 0 0 56 1373 No Steel Added 16 151.7 1920.58 844 750 3 H32 @ 316.5
RAPT 6.6.8.0 Project Name: J110 Page 2/16
Licensee: AECOM Singapore Pte Ltd 1/6/2022 7:53:23 PM License No.: 10479063400712WPN11
Frame Description: G/8/B/2
Project Name: J110 Column Punching
Frame Description: G/8/B/2 Shear Check
required
Designer: SLT Y/N
C:\Users\sujeevanleonard.tham\OneDrive - AECOM\Projects\J110\J110\OneDrive_2021-07-01\12. Southern 1 N
Staircase\Design Files\Str\Beams\G,8,B,2.rpf 2 N
Reinforcement
Reinforcement Reinforcement Preferred Number
Load Combinations : Transfer Prestress Use Type Bar Size of Legs
Load Description 1. Self 2. Extra 3. Live List List #
Combination Weight Dead Load Load Flexural Bar H 500MPa
A #.# #.# #.#
Flexural Mesh A 500MPa
1 Transfer 1 0 0 Shear Option 1 H 500MPa 10 2
Shear Option 2 H 500MPa 10 4
Shear Option 3 H 500MPa 10 6
Load Combinations : Pre Existing Punching Shear H 500MPa 10 2
Load Description 1. Self 2. Extra 3. Live
Combination Weight Dead Load Load
A #.# #.# #.#
1 Pre Existing 1 0 0
Reinforcement
Maximum Minimum Minimum Minimum Span Minimum Span Infill Stagger
Bar Bar Continuous Reinforcement Reinforcement Bars Bars
Spacing Spacing Reinforcement into End into Internal
Support Support
mm mm #.# #.# #.# Y/N Y/N
Support Reinforcement 300 60 0 N N
RAPT 6.6.8.0 Project Name: J110 Page 5/16 RAPT 6.6.8.0 Project Name: J110 Page 6/16
Licensee: AECOM Singapore Pte Ltd 1/6/2022 7:53:35 PM License No.: 10479063400712WPN11 Licensee: AECOM Singapore Pte Ltd 1/6/2022 7:53:38 PM License No.: 10479063400712WPN11
Frame Description: G/8/B/2 Frame Description: G/8/B/2
Reinforcement Design Zones User Defined
Maximum Minimum Minimum Minimum Span Minimum Span Infill Stagger
Bar Bar Continuous Reinforcement Reinforcement Bars Bars 1 2
Spacing Spacing Reinforcement into End into Internal mm
Support Support 0
mm mm #.# #.# #.# Y/N Y/N
Span Reinforcement 300 60 0 0 N N -200
-400
User Defined
Layer Steel type Left End Distance Bar Top % Development % Development Right End Distance Bar Top % Development Maximum Service Stress Change - Prestressed Sections MPa 200
Number Reference to left stagger Cover of Left End of of Left End of Bar Reference to right stagger Cover of Right End of Maximum Service Stress Change - Reinforced Sections MPa 200
Column end of length at at left Bar in Tension in Compression Column end of length at at Right Bar in Tension Relative Humidity % 50
bar left end end bar right end end Average Temperature C. 20
List # mm mm mm % % # mm mm mm % Prestress Losses Calculations based on List Program Default
1 H 500MPa 1 0 0 40 0 0 2 0 0 40 0 Crack Width Calculations List .20 mm
AS3600 Shrinkage and Temperature Reinforcement List Moderate
Layer % Development Bar Number Spacing % in Layer attached Degree of Restraint in Primary Direction % 0
Number of Right End of Size of Bars of Bars Flange after the Degree of Restraint in Secondary Direction % 0
Bar in PreExisting Load Concrete Strength Gain Rate List N
Compression Case
% List # mm % Y/N
Concrete Tensile Strength for Deflection Calculations- #.## x (Fc)n #.# -1
1 0 25 7 0 0 N
Maximum Value of Ieff/Igross for Deflection Calculations #.# 0.6
Total Deflection Warning Limit - Maximum Span/Deflection #.# 250
Total Deflection Warning Limit - Maximum Deflection mm 40
Reinforcement Design Zones Incremental Deflection Warning Limit - Maximum Span/Deflection #.# 360
Incremental Deflection Warning Limit - Maximum Deflection mm 25
1 2 List
Initial Time for Shrinkage Full Shrinkage
mm
Time of Loading in days #.# 10
0
Age Adjustment Factor #.# 0.76
-200 Concrete Strength at Time of Loading MPa 27.04
Loaded Period in years #.# 30
-400 Tension stiffening Approach List Modified Concrete Tensile Modulus Method
-600
Live Load Pattern Factor #.#
-800 Pattern Live Load for Ultimate Strength Y/N
Pattern Live Load for Crack Control Y/N
0 10600mm
Pattern Live Load For Deflections Y/N
Pattern Live Load for Deflection Permanent Load Combination Y/N
Material Properties
RAPT 6.6.8.0 Project Name: J110 Page 7/16 RAPT 6.6.8.0 Project Name: J110 Page 8/16
Licensee: AECOM Singapore Pte Ltd 1/6/2022 7:53:42 PM License No.: 10479063400712WPN11 Licensee: AECOM Singapore Pte Ltd 1/6/2022 7:53:46 PM License No.: 10479063400712WPN11
Frame Description: G/8/B/2 Frame Description: G/8/B/2
Concrete : Standard Concrete : Concrete Strength Basis - Cube Full Elevation View
Description A C32/40MPa
Characteristic Compressive Strength MPa 40 mm 1 2
Mean Compressive Strength MPa 50 3000
Lower Characteristic Tensile Strength MPa 2.12
Upper Characteristic Tensile Strength MPa 3.93 2000
Concrete Density kg/m3 2447
Design Concrete Modulus MPa 31186.6 1000
Mean Concrete Modulus MPa 33345.8
Basic Shrinkage Strain mm/mm 0 0
Shrinkage Multiplier #.# 1
Basic Creep Factor #.# 2.656 -1000
Creep Multiplier #.# 1 0 10600mm
Concrete Strain at Peak Stress #.# 0.002 Warnings
Squash Load Factor #.# 0.85 Input
Concrete Strain Limit #.# 0.004 No errors or warnings were found.
Strength Gain Rate List Normal
Maximum Aggregate Size mm 20 Output
No errors or warnings were found.
Reinforcement Bar
Designation Type Yield Elastic Ductility Peak Peak Design Material Material Material Capacity Material Capacity Include as Description
Stress Modulus Strain Stress Strain Factor Factor Reduction Factor Reduction Factor Flexural
Limit Flexure Shear - Flexure - Shear Reinforcement for Bending Moments
Shear Load Cases
H Deformed 500 2.05e5 N 0.05 540 90 -1 -1 -1 -1 Y Column Actions
Col No. 1 Self Extra Dead Live
Weight Load Load
Nominal Bar Bar Area Bar Bar Stock Moment Above kNm 0 0 0
Bar Size Diameter Inertia Weight Length Moment Below kNm 0 0 0
A mm mm2 mm4 kg/m mm Reaction kN 233.31 67.48 134.97
10 10 78.5 491.07 0.62 12000 Elastic Rotation #.# 1.68e-3 5.13e-4 1.03e-3
13 13 132.7 1402.55 1.04 12000 Elastic Axial Shortening mm -0 -0 -0
16 16 201.1 3218.29 1.58 12000
20 20 314.2 7857.14 2.47 12000 Col No. 2 Self Extra Live Load
22 22 380.1 11503.6 2.98 12000 Weight Dead
25 25 490.9 19182.5 3.85 12000 Load
32 32 804.2 51492.6 6.31 12000 Moment Above kNm 0 0 0
40 40 1256.6 1.257e5 9.86 12000 Moment Below kNm 0 0 0
Reaction kN 195.57 52.39 104.78
Elastic Rotation #.# -1.58e-3 -4.73e-4 -9.47e-4
Elevation view
Elastic Axial Shortening mm -0 -0 -0
1 2
mm
0
Load Combinations
-200 Column Actions
Col No. 1 Characteristic Characteristic Service Service Ultimate Ultimate Ultimate Ultimate
-400 Service Service (Reversal) Flexure Flexure Shear Shear
(Reversal) (Reversal) (Reversal)
-600
Moment Above kNm 0 0 0 0 0 0 0 0
-800 Moment Below kNm 0 0 0 0 0 0 0 0
Reaction kN 435.76 435.76 368.27 368.27 608.52 608.52 428.63 608.52
0 10600mm Elastic Rotation #.# 3.22e-3 3.22e-3 2.7e-3 2.7e-3 4.5e-3 4.5e-3 3.12e-3 4.5e-3
Elastic Axial Shortening mm -0 -0 -0 -0 -0 -0 -0 -0
Plan view
Col No. 2 Characteristic Characteristic Service Service Ultimate Ultimate Ultimate Ultimate
1 2
Service Service (Reversal) Flexure Flexure Shear Shear
(Reversal) (Reversal) (Reversal)
mm Moment Above kNm 0 0 0 0 0 0 0 0
-200 Moment Below kNm 0 0 0 0 0 0 0 0
Reaction kN 352.74 352.74 300.35 300.35 491.92 491.92 353.34 491.92
0 Elastic Rotation #.# -3e-3 -3e-3 -2.53e-3 -2.53e-3 -4.19e-3 -4.19e-3 -2.93e-3 -4.19e-3
Elastic Axial Shortening mm -0 -0 -0 -0 -0 -0 -0 -0
200
0 10600mm
RAPT 6.6.8.0 Project Name: J110 Page 9/16 RAPT 6.6.8.0 Project Name: J110 Page 10/16
Licensee: AECOM Singapore Pte Ltd 1/6/2022 7:53:49 PM License No.: 10479063400712WPN11 Licensee: AECOM Singapore Pte Ltd 1/6/2022 7:53:53 PM License No.: 10479063400712WPN11
Frame Description: G/8/B/2 Frame Description: G/8/B/2
Ultimate Design Flexural Design
Flexure Ultimate
kNm
1 2 mm21 2
-300 75.8 40000 0
61.2
0 2000
300 0
600
900 -2000
1200 -4000
1500 -6000
1800
2100 -8000
2400 2073 -10000 8231
0 10600mm 0 10600mm
Moment Moment 1 Moment 2 Reinforcement Top Total Bottom Total Top Ultimate Bottom Ultimate Min Top Min Bot
kN1 2 1 2
kNm
800 -400
582
600 0
400 400
800
200 1200
0 1600
-200 2000
-400 2400
2800
-600 -466 3200
0 10600mm 0 10600mm
Shear 1 2
0.04
1 2 0
kNm
-300 75.8 61.2 -0.04
0 -0.08
300
-0.12
600
900 -0.16
1200 -0.2
1500 -0.24
0.229
1800
2100 1795 0 10600mm
2400
0 10600mm Neutral Axis Depth Initial Final
Moment Moment 1 Moment 2 Span 1
Design Comments:-
- As there is no area of steel in the tension zone (any prestressing tendons are in the compression zone) we are now adding an area of steel, equivalent to
kN1 2 that required for minimum reinforcement, to the design tension layer. This is then assumed to be the initial design reinforcement setup. More reinforcement will
800 be added as required to achieve the applied moments. Ast added = 878.24mm2 @ 485mm
582
600
400
200
Service
0
-200
-400 1 2
-600 -466 MPa MPa
-12 -10.24 -180
0 10600mm
-8 -120
Shear Shear 1 Shear 2 -4 -60
0 0
4 60
8 120
12 180
16 10.59 240
0 10600mm
RAPT 6.6.8.0 Project Name: J110 Page 11/16 RAPT 6.6.8.0 Project Name: J110 Page 12/16
Licensee: AECOM Singapore Pte Ltd 1/6/2022 7:53:57 PM License No.: 10479063400712WPN11 Licensee: AECOM Singapore Pte Ltd 1/6/2022 7:54:02 PM License No.: 10479063400712WPN11
Frame Description: G/8/B/2 Frame Description: G/8/B/2
Reversal Moment Condition Characteristic Service
Maximum Moment Condition
1 2
MPa MPa 1 2
-12 -9.76 -180 MPa MPa
-8 -120 -16 -12.2 -320
-12 -240
-4 -60 -8 -160
0 0 -4 -80
4 60 0 0
8 120 4 80
8 160
12 180 12 240
16 10.39 240 16 320
0 10600mm 20 12.62 400
0 10600mm
Gross Stress Top Gross Stress Bottom Cracked Compression Reinforcement Tension Limits
Gross Stress Top Gross Stress Bottom Cracked Compression Reinforcement Tension Limits
Span 1
Design Comments:- Reversal Moment Condition
- Increase in stress from decompression to working exceeds 200MPa in at least one steel layer. Reinforcement has been added to reduce stress change
below this maximum value. Refer RAPT manual Section T.7.6 1 2
MPa MPa
-16 -11.63 -320
-12 -240
-8 -160
Permanent -4 -80
Maximum Moment Condition 0 0
4 80
1 2 8 160
MPa MPa 12 240
-12 -9.01 -200 16 320
-9 -150 20 12.38 400
-6 -100 0 10600mm
-3 -50
0 0 Gross Stress Top Gross Stress Bottom Cracked Compression Reinforcement Tension Limits
3 50
6 100
9 150 Shear Design
12 200
15 9.59 250 Beam
0 10600mm Span 1
Locat V* Mv* Pv Mdec d Ast bv phi Vuc phi Vut phi Vu Phi Vumax phi VuMin phi Vus Theta Asv/s
Gross Stress Top Gross Stress Bottom Cracked Compression Reinforcement Tension Limits
mm1 2
0
-20
Punching -40 -33.1
Column Head Critical Section
Column Bh a at u d fcv P/A Asw/s min V* Mv* V*eff VRd1 VRd2 Asv result -60
No.
A #.# mm mm mm mm MPa MPa mm2/mm kN kNm kN kN kN mm2 A -80
1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Check Not Requested! 320
2 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Check Not Requested! 0 10600mm
Detailed Reinforcement
Span 1
Deflections Top Reinforcement Bottom Reinforcement
All Spans Loaded
Transfer Max Max Section Max Max Section
Locat Size Space Area Depth Width Rebar Reqd Size Space Area Depth Width Rebar Reqd
mm mm mm mm2 mm mm A mm mm mm2 mm mm A
mm1 2
0 125 0 0 0 56 750 No Steel Added 25 300 1982.24 844 750 2 H40 @ 625
485 0 0 0 56 750 No Steel Added 16 151.1 2561.24 844 750 3 H40 @ 312.5
-20 -10.8 845 0 0 0 56 750 No Steel Added 16 150.6 3149.26 844 750 3 H40 @ 312.5
899 0 0 0 56 750 No Steel Added 16 150.5 3237.09 844 750 3 H40 @ 312.5
-40 901 0 0 0 56 750 No Steel Added 16 150.5 3240.33 844 750 3 H40 @ 312.5
1250 0 0 0 56 750 No Steel Added 16 150.6 3802.52 844 750 4 H40 @ 208.3
-60
1599 0 0 0 56 750 No Steel Added 16 150.6 4356.13 844 750 4 H40 @ 208.3
-80 1948 0 0 0 56 750 No Steel Added 16 150.6 4900.04 844 750 4 H40 @ 208.3
986 2297 0 0 0 56 750 No Steel Added 16 150.5 5436.13 844 750 5 H40 @ 156.3
0 10600mm 2650 0 0 0 56 750 No Steel Added 16 150.5 5984.62 844 750 5 H40 @ 156.3
3399 0 0 0 56 750 No Steel Added 16 150.5 7583.41 844 750 7 H40 @ 104.2
3401 0 0 0 56 750 No Steel Added 16 150.5 7586.02 844 750 7 H40 @ 104.2
4350 0 0 0 56 750 No Steel Added 16 150.5 8009.91 844 750 7 H40 @ 104.2
5300 0 0 0 56 750 No Steel Added 16 150.5 8304.07 844 750 7 H40 @ 104.2
5599 0 0 0 56 750 No Steel Added 16 150.5 8369.51 844 750 7 H40 @ 104.2
5601 0 0 0 56 750 No Steel Added 16 150.5 8368.31 844 750 7 H40 @ 104.2
6384 0 0 0 56 750 No Steel Added 16 150.5 7234.65 844 750 6 H40 @ 125
7167 0 0 0 56 750 No Steel Added 16 150.5 6026.54 844 750 5 H40 @ 156.3
7950 0 0 0 56 750 No Steel Added 16 150.5 4747.78 844 750 4 H40 @ 208.3
8303 0 0 0 56 750 No Steel Added 16 150.6 4294.12 844 750 4 H40 @ 208.3
8652 0 0 0 56 750 No Steel Added 16 150.6 3883.29 844 750 4 H40 @ 208.3
RAPT 6.6.8.0 Project Name: J110 Page 15/16 RAPT 6.6.8.0 Project Name: J110 Page 16/16
Licensee: AECOM Singapore Pte Ltd 1/6/2022 7:54:15 PM License No.: 10479063400712WPN11 Licensee: AECOM Singapore Pte Ltd 1/6/2022 7:54:19 PM License No.: 10479063400712WPN11
Frame Description: G/8/B/2 Frame Description: G/8/B/2
Top Reinforcement Bottom Reinforcement - - Span 1 - Required Bar Size is greater than the Preferred Bar Size. Maintaining the same cover will require slightly more reinforcement than calculated.
RAPT has increased the required reinforcement by the ratio of the effective depths for the 2 bar sizes in the reinforcement layout.
Max Max Section Max Max Section Design Comments:-
Locat Size Space Area Depth Width Rebar Reqd Size Space Area Depth Width Rebar Reqd - Span - 1 - Reinforcement added at left span contraflexure point for Offset of Bending Moment Diagram for Shear - 1749.53mm2
mm mm mm mm2 mm mm A mm mm mm2 mm mm A - Span - 1 - Reinforcement added at right span contraflexure point for Offset of Bending Moment Diagram for Shear - 1414.27mm2
9001 0 0 0 56 750 No Steel Added 16 150.6 3462.8 844 750 3 H40 @ 312.5
9350 0 0 0 56 750 No Steel Added 16 150.6 3031.08 844 750 3 H40 @ 312.5
9699 0 0 0 56 750 No Steel Added 16 150.6 2589.98 844 750 3 H40 @ 312.5
9701 0 0 0 56 750 No Steel Added 16 150.6 2587.43 844 750 3 H40 @ 312.5
9755 0 0 0 56 750 No Steel Added 16 150.8 2518.42 844 750 3 H40 @ 312.5
10115 0 0 0 56 750 No Steel Added 16 174.8 2058.69 844 750 2 H40 @ 625
10475 0 0 0 56 750 No Steel Added 25 300 1600.11 844 750 2 H40 @ 625
Shear Reinforcement
Spacing of Sets
2 legs 4 legs 6 legs Min legs Minimum Shear
Area H10 H10 H10 H10 Legs Comments
mm2/mm mm mm mm mm # A
Design Comments:-
- - Span 1 - Required Bar Size is greater than the Preferred Bar Size. Maintaining the same cover will require slightly more reinforcement than calculated.
RAPT has increased the required reinforcement by the ratio of the effective depths for the 2 bar sizes in the reinforcement layout.
- Span - 1 - Reinforcement added at left span contraflexure point for Offset of Bending Moment Diagram for Shear - 1749.53mm2
- Span - 1 - Reinforcement added at right span contraflexure point for Offset of Bending Moment Diagram for Shear - 1414.27mm2
Reinforcement Layout
(7-H25)
1 2
mm
0
-200
-400
-600
-800
7-H40
0 10600mm
RAPT 6.6.8.0 Project Name: J110 Page 2/13
Licensee: AECOM Singapore Pte Ltd 1/6/2022 7:52:38 PM License No.: 10479063400712WPN11
Frame Description: G/8/B/3-1
Project Name: J110 Beams
Frame Description: G/8/B/3-1 Beam Beam Beam Beam Effective
Designer: SLT Number Depth Width Width Flange
C:\Users\sujeevanleonard.tham\OneDrive - AECOM\Projects\J110\J110\OneDrive_2021-07-01\12. Southern at Width
Slab
Staircase\Design Files\Str\Beams\G,8,B,3-1.rpf mm mm mm mm
1 700 500 500 500
RAPT - Version: 6.6.8.0
Reinforced And Post-Tensioned Concrete Analysis & Design Package
Copyright(C) 1988 - 2021 PCDC Pty. Ltd. All Rights Reserved
Load Cases
Load Load Type Load Definition Live Load Description
Licensee Case Deflection Case
AECOM Singapore Pte Ltd
300 Beach Road List List Y/N A
#03-00 The Concourse 1 Self Weight Applied Loads
Singapore 199555 2 Extra Dead Load Applied Loads
10479063400712WPN11 3 Live Load Applied Loads Y
Limit Reinforcement Strain Y/N Y Nominal Bar Bar Area Bar Bar Stock
Include Strain Hardening of Reinforcement Y/N N Bar Size Diameter Inertia Weight Length
Beam Shear Critical Section Location List Code Critical Section A mm mm2 mm4 kg/m mm
13 13 132.7 1402.55 1.04 12000
16 16 201.1 3218.29 1.58 12000
20 20 314.2 7857.14 2.47 12000
Maximum Service Stress Change - Prestressed Sections MPa 200
22 22 380.1 11503.6 2.98 12000
Maximum Service Stress Change - Reinforced Sections MPa 200
25 25 490.9 19182.5 3.85 12000
Relative Humidity % 50
32 32 804.2 51492.6 6.31 12000
Average Temperature C. 20
40 40 1256.6 1.257e5 9.86 12000
Prestress Losses Calculations based on List Program Default
Crack Width Calculations List .20 mm
AS3600 Shrinkage and Temperature Reinforcement List Moderate Elevation view
Degree of Restraint in Primary Direction % 0
Degree of Restraint in Secondary Direction % 0 1 2
mm
Concrete Strength Gain Rate List N 0
Concrete Tensile Strength for Deflection Calculations- #.## x (Fc)n #.# -1 -200
Maximum Value of Ieff/Igross for Deflection Calculations #.# 0.6
Total Deflection Warning Limit - Maximum Span/Deflection #.# 250 -400
Total Deflection Warning Limit - Maximum Deflection mm 40
Incremental Deflection Warning Limit - Maximum Span/Deflection #.# 360 -600
Incremental Deflection Warning Limit - Maximum Deflection mm 25
Initial Time for Shrinkage List Full Shrinkage
0 5000mm
Time of Loading in days #.# 10
Age Adjustment Factor #.# 0.76
Plan view
Concrete Strength at Time of Loading MPa 27.04
Loaded Period in years #.# 30 mm1 2
Tension stiffening Approach List Modified Concrete Tensile Modulus Method -1200
0.088
-30 -0.1
0 14.8 14.8 0 5000mm
30
60 Neutral Axis Depth Initial Final
90
120
150
180 160
210
0 5000mm
Gross Stress Top Gross Stress Bottom Cracked Compression Reinforcement Tension Limits Gross Stress Top Gross Stress Bottom Cracked Compression Reinforcement Tension Limits
1 2 1 2
MPa MPa
MPa MPa
-4 -2.74 -200 -3.18
-4 -400
-2 -100 -2 -200
0 0 0 0
2 200
2 100
4 400
4 200 6 600
6 300 8 800
2.81 10 3.26 1000
8 400
0 5000mm 0 5000mm
Gross Stress Top Gross Stress Bottom Cracked Compression Reinforcement Tension Limits Gross Stress Top Gross Stress Bottom Cracked Compression Reinforcement Tension Limits
Span 1
Design Comments:-
Shear Design
- Increase in stress from decompression to working exceeds 200MPa in at least one steel layer. Reinforcement has been added to reduce stress change Beam
below this maximum value. Refer RAPT manual Section T.7.6 Span 1
Locat V* Mv* Pv Mdec d Ast bv phi Vuc phi Vut phi Vu Phi Vumax phi VuMin phi Vus Theta Asv/s
MPa1 2MPa
-4 -200 Spacing of Sets Minimum Legs Shear Comments
-2.56 2 legs 4 legs 6 legs Min legs
-3 -150
-2 -100 H10 H10 H10 H10
-1 -50 mm mm mm mm # A
0 0
1 50
2 100 346.9 483 483 346.9 2 Minimum Steel
3 150 346.9 483 483 346.9 2 Minimum Steel
4 200
5 250 346.9 483 483 346.9 2 Minimum Steel
6 300 346.9 483 483 346.9 2 Minimum Steel
7 2.63 350
346.9 483 483 346.9 2 Minimum Steel
0 5000mm
346.9 483 483 346.9 2 Minimum Steel
346.9 483 483 346.9 2 Minimum Steel
RAPT 6.6.8.0 Project Name: J110 Page 11/13 RAPT 6.6.8.0 Project Name: J110 Page 12/13
Licensee: AECOM Singapore Pte Ltd 1/6/2022 7:53:10 PM License No.: 10479063400712WPN11 Licensee: AECOM Singapore Pte Ltd 1/6/2022 7:53:14 PM License No.: 10479063400712WPN11
Frame Description: G/8/B/3-1 Frame Description: G/8/B/3-1
Incremental
Spacing of Sets Minimum Legs Shear Comments
2 legs 4 legs 6 legs Min legs mm1 2
H10 H10 H10 H10 0
mm mm mm mm # A
346.9 483 483 346.9 2 Minimum Steel -3
346.9 483 483 346.9 2 Minimum Steel -4.11
-6
346.9 483 483 346.9 2 Minimum Steel
346.9 483 483 346.9 2 Minimum Steel -9
346.9 483 483 346.9 2 Minimum Steel
346.9 483 483 346.9 2 Minimum Steel -12
346.9 483 483 346.9 2 Minimum Steel 1218
346.9 483 483 346.9 2 Minimum Steel 0 5000mm
mm1 2
0
Punching
Column Head Critical Section -3
Column Bh a at u d fcv P/A Asw/s min V* Mv* V*eff VRd1 VRd2 Asv result
-6 -4.81
No.
A #.# mm mm mm mm MPa MPa mm2/mm kN kNm kN kN kN mm2 A
-9
1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Check Not Requested!
2 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Check Not Requested! -12
1040
0 5000mm
Design Comments:-
- - Span 1 - Required Bar Size is smaller than the Preferred Bar Size. Maintaining the same cover will require slightly less reinforcement than calculated.
- Span - 1 - Reinforcement added at left span contraflexure point for Offset of Bending Moment Diagram for Shear - 433.67mm2
- Span - 1 - Reinforcement added at right span contraflexure point for Offset of Bending Moment Diagram for Shear - 433.67mm2
Reinforcement Layout
1 2
mm
0
-200
-400
-600
4-H20
0 5000mm
- - Span 1 - Required Bar Size is smaller than the Preferred Bar Size. Maintaining the same cover will require slightly less reinforcement than calculated.
Design Comments:-
- Span - 1 - Reinforcement added at left span contraflexure point for Offset of Bending Moment Diagram for Shear - 433.67mm2
- Span - 1 - Reinforcement added at right span contraflexure point for Offset of Bending Moment Diagram for Shear - 433.67mm2
RAPT 6.6.8.0 Project Name: J110 Page 2/13
Licensee: AECOM Singapore Pte Ltd 1/6/2022 7:51:45 PM License No.: 10479063400712WPN11
Frame Description: G/8/B/3-1a
Project Name: J110 Beams
Frame Description: G/8/B/3-1a Beam Beam Beam Beam Effective
Designer: SLT Number Depth Width Width Flange
C:\Users\sujeevanleonard.tham\OneDrive - AECOM\Projects\J110\J110\OneDrive_2021-07-01\12. Southern at Width
Slab
Staircase\Design Files\Str\Beams\G,8,B,3-1a.rpf mm mm mm mm
1 900 500 500 500
RAPT - Version: 6.6.8.0
Reinforced And Post-Tensioned Concrete Analysis & Design Package
Copyright(C) 1988 - 2021 PCDC Pty. Ltd. All Rights Reserved
Load Cases
Load Load Type Load Definition Live Load Description
Licensee Case Deflection Case
AECOM Singapore Pte Ltd
300 Beach Road List List Y/N A
#03-00 The Concourse 1 Self Weight Applied Loads
Singapore 199555 2 Extra Dead Load Applied Loads
10479063400712WPN11 3 Live Load Applied Loads Y
Due to the different Concrete Strength types in the Design Standard and Materials in this run, the concrete strengths shown in the materials data have been Load Combinations : Ultimate
multiplied in the calculatiuons by 0.8 Load Description 1. Self 2. Extra 3.
Combination Weight Dead Live
Span Load Load
A #.# #.# #.#
Span Span Slab Panel Panel External External Edge
Length Depth Width Width Edge Distance 1 Live Load 1.35 1.35 1.5
Left Right Distance Left Right 2 Live Load 1 1 1.5
mm mm mm mm mm mm 3 Dead Load 1.425 1.425 0
LE 0
1 5000 200 1500 1500 0 0
RE 0 Load Combinations : Short Term Service
Load Description 1. Self 2. Extra 3. Live
Combination Weight Dead Load Load
Columns A #.# #.# #.#
Column Column Support Transverse 1 Live Load 1 1 0.5
Grid Type Column
Reference spacing
A List mm
Load Combinations : Permanent Service
1 1 Knife-Edge 3000
Load Description 1. Self 2. Extra 3. Live
2 2 Knife-Edge 3000 Combination Weight Dead Load Load
A #.# #.# #.#
1 Live Load 1 1 0.3
RAPT 6.6.8.0 Project Name: J110 Page 3/13 RAPT 6.6.8.0 Project Name: J110 Page 4/13
Licensee: AECOM Singapore Pte Ltd 1/6/2022 7:51:48 PM License No.: 10479063400712WPN11 Licensee: AECOM Singapore Pte Ltd 1/6/2022 7:51:52 PM License No.: 10479063400712WPN11
Frame Description: G/8/B/3-1a Frame Description: G/8/B/3-1a
Load Combinations : Deflection
Load Description 1. Self 2. Extra 3. Live Reinforcement Reinforcement Preferred Number
Combination Weight Dead Load Load Use Type Bar Size of Legs
A #.# #.# #.# List List #
1 Short Term - Deflection 1 1 0.5 Shear Option 2 H 500MPa 10 4
2 Permanent - Deflection 1 1 0.3 Shear Option 3 H 500MPa 10 6
3 Initial - Deflection 1 0 0 Punching Shear H 500MPa 10 2
kN/m1 2
Design Zones
20 Layer Steel Left End Distance to Bar stagger Bottom Right End Distance to Bar stagger Bottom Maximum Minimum Preferred
15
Number type Reference left end of length at left Cover at left Reference right end of length at right Cover at Bar Size Bar Size bar size
10
L2 Column bar end end Column bar end Right End
5
List # mm mm mm # mm mm mm List List List
0
0 5000mm 1 Bar 1 0 0 40 2 0 0 40 40 20 32
20 L1
15 Layer Minimum Maximum Minimum % in
10
Number Number of Spacing of Steel area as Flange
5
Bars Bars %
0
# mm % %
1 2
1 0 0 0 0
1500
Material Properties 0 5000mm
Concrete : Standard Concrete : Concrete Strength Basis - Cube Warnings
Description A C32/40MPa Input
Characteristic Compressive Strength MPa 40 No errors or warnings were found.
Mean Compressive Strength MPa 50
Lower Characteristic Tensile Strength MPa 2.12 Output
Upper Characteristic Tensile Strength MPa 3.93 Warning:SPAN Reinforcing Bar spacing There have been problems in determining a bar size to satisfy the design spacing requirements. See Detailed
Concrete Density kg/m3 2447 Reinforcement Design Comments.
Design Concrete Modulus MPa 31186.6
Mean Concrete Modulus MPa 33345.8
Basic Shrinkage Strain mm/mm 0
Shrinkage Multiplier #.# 1
#.#
Bending Moments
Basic Creep Factor 2.656
Creep Multiplier #.# 1 Load Cases
Concrete Strain at Peak Stress #.# 0.002 Column Actions
Squash Load Factor #.# 0.85 Col No. 1 Self Extra Dead Live
Concrete Strain Limit #.# 0.004 Weight Load Load
List Moment Above kNm -0 -0 -0
Strength Gain Rate Normal
mm Moment Below kNm -0 -0 -0
Maximum Aggregate Size 20
Reaction kN 53.13 9.38 18.75
Elastic Rotation #.# 1.09e-4 0 0
Elastic Axial Shortening mm 0 0 0
RAPT 6.6.8.0 Project Name: J110 Page 7/13 RAPT 6.6.8.0 Project Name: J110 Page 8/13
Licensee: AECOM Singapore Pte Ltd 1/6/2022 7:52:04 PM License No.: 10479063400712WPN11 Licensee: AECOM Singapore Pte Ltd 1/6/2022 7:52:07 PM License No.: 10479063400712WPN11
Frame Description: G/8/B/3-1a Frame Description: G/8/B/3-1a
Col No. 2 Self Extra Dead Live Shear
Weight Load Load
Moment Above kNm -0 -0 -0 1 2
Moment Below kNm -0 -0 -0 kNm
-20
Reaction kN 53.13 9.38 18.75 11 11
0
Elastic Rotation #.# -1.09e-4 0 0 20
Elastic Axial Shortening mm 0 0 0 40
60
80
100
Load Combinations 120
Column Actions 140 123
160
Col No. 1 Characteristic Characteristic Service Service Ultimate Ultimate Ultimate Ultimate
0 5000mm
Service Service (Reversal) Flexure Flexure Shear Shear
(Reversal) (Reversal) (Reversal)
kNm
Moment Moment 1 Moment 2
Moment Above 0 0 0 0 0 0 0 0
Moment Below kNm 0 0 0 0 0 0 0 0
Reaction kN 81.25 81.25 71.88 71.88 112.5 112.5 89.06 112.5 1 2
Elastic Rotation #.# 1.67e-4 1.67e-4 1.48e-4 1.48e-4 2.31e-4 2.31e-4 1.83e-4 2.31e-4 kN
Elastic Axial Shortening mm 0 0 0 0 0 0 0 0 120 80.5
80
Col No. 2 Characteristic Characteristic Service Service Ultimate Ultimate Ultimate Ultimate 40
Service Service (Reversal) Flexure Flexure Shear Shear 0
(Reversal) (Reversal) (Reversal)
-40
Moment Above kNm 0 0 0 0 0 0 0 0
kNm -80
Moment Below 0 0 0 0 0 0 0 0 -80.5
Reaction kN 81.25 81.25 71.88 71.88 112.5 112.5 89.06 112.5 -120
Elastic Rotation #.# -1.67e-4 -1.67e-4 -1.48e-4 -1.48e-4 -2.31e-4 -2.31e-4 -1.83e-4 -2.31e-4 0 5000mm
Elastic Axial Shortening mm 0 0 0 0 0 0 0 0
Shear Shear 1 Shear 2
kNm
1 2 mm21 2
-20 3000 0
11 11 200
0 100
20 0
40 -100
60 -200
80 -300
100 -400
-500
120 -600
140 -700
160 141 -800 655
0 5000mm 0 5000mm
Moment Moment 1 Moment 2 Reinforcement Top Total Bottom Total Top Ultimate Bottom Ultimate Min Top Min Bot
1 2 kNm1 2
kN -40
120 80.1 0
80 40
40 80
0 120
-40 160
-80 200
-120 -80.1 240
280
0 5000mm 0 5000mm
0.051
-0.056 3.2 400
0 5000mm 4 1.25 500
0 5000mm
Neutral Axis Depth Initial Final
Gross Stress Top Gross Stress Bottom Cracked Compression Reinforcement Tension Limits
Service
Maximum Moment Condition Characteristic Service
Maximum Moment Condition
1 2
MPa MPa 1 2
-1.3
-1.6 -200 MPa MPa
-0.8 -100 -1.47
-1.8 -200
0 0 -0.9 -100
0.8 100 0 0
1.6 200 0.9 100
2.4 300 1.8 200
3.2 400 2.7 300
4 500 3.6 400
1.32
0 5000mm 4.5 500
1.49
0 5000mm
Gross Stress Top Gross Stress Bottom Cracked Compression Reinforcement Tension Limits
Gross Stress Top Gross Stress Bottom Cracked Compression Reinforcement Tension Limits
Reversal Moment Condition
Reversal Moment Condition
1 2
MPa MPa 1 2
-1.3
-1.6 -200 MPa MPa
-0.8 -100 -1.47
-1.8 -200
0 0 -0.9 -100
0.8 100 0 0
1.6 200 0.9 100
2.4 300 1.8 200
3.2 400 2.7 300
4 500 3.6 400
1.32
0 5000mm 4.5 500
1.49
0 5000mm
Gross Stress Top Gross Stress Bottom Cracked Compression Reinforcement Tension Limits
Gross Stress Top Gross Stress Bottom Cracked Compression Reinforcement Tension Limits
Permanent
Maximum Moment Condition Shear Design
Beam
1 2 Span 1
MPa MPa
-1.6 -1.23 -200 Locat V* Mv* Pv Mdec d Ast bv phi Vuc phi Vut phi Vu Phi Vumax phi VuMin phi Vus Theta Asv/s
-0.8 -100
0 0
mm kN kNm kN kNm mm mm2 mm kN kN kN kN kN kN #.# mm2/mm
0.8 100
100 108 11.03 0 0 844 654.72 500 0 0 0 2119.59 0 0 0
1.6 200
720 80.54 67.46 0 0 844 654.72 500 151.47 99999 151.47 2119.59 373.67 0 21.8 0.45
2.4 300
896 72.62 80.93 0 0 844 654.72 500 151.47 99999 151.47 2119.59 373.67 0 21.8 0.45
3.2 400 1072 64.7 93.02 0 0 844 654.72 500 151.47 99999 151.47 2119.59 373.67 0 21.8 0.45
4 1.25 500 1250 58.01 98.88 0 0 844 654.72 500 151.47 99999 151.47 2119.59 373.67 0 21.8 0.45
0 5000mm 1666 39.29 119.11 0 0 844 654.72 500 151.47 99999 151.47 2119.59 373.67 0 21.8 0.45
2082 22.77 125.15 0 0 844 654.72 500 151.47 99999 151.47 2119.59 373.67 0 21.8 0.45
Gross Stress Top Gross Stress Bottom Cracked Compression Reinforcement Tension Limits
2500 -7.03 123.05 0 0 844 654.72 500 151.47 99999 151.47 2119.59 373.67 0 21.8 0.45
2918 -22.77 125.15 0 0 844 654.72 500 151.47 99999 151.47 2119.59 373.67 0 21.8 0.45
3334 -39.29 119.11 0 0 844 654.72 500 151.47 99999 151.47 2119.59 373.67 0 21.8 0.45
3750 -58.01 98.88 0 0 844 654.72 500 151.47 99999 151.47 2119.59 373.67 0 21.8 0.45
3928 -64.7 93.02 0 0 844 654.72 500 151.47 99999 151.47 2119.59 373.67 0 21.8 0.45
4104 -72.62 80.93 0 0 844 654.72 500 151.47 99999 151.47 2119.59 373.67 0 21.8 0.45
4280 -80.54 67.46 0 0 844 654.72 500 151.47 99999 151.47 2119.59 373.67 0 21.8 0.45
RAPT 6.6.8.0 Project Name: J110 Page 11/13 RAPT 6.6.8.0 Project Name: J110 Page 12/13
Licensee: AECOM Singapore Pte Ltd 1/6/2022 7:52:16 PM License No.: 10479063400712WPN11 Licensee: AECOM Singapore Pte Ltd 1/6/2022 7:52:19 PM License No.: 10479063400712WPN11
Frame Description: G/8/B/3-1a Frame Description: G/8/B/3-1a
Incremental
Locat V* Mv* Pv Mdec d Ast bv phi Vuc phi Vut phi Vu Phi Vumax phi VuMin phi Vus Theta Asv/s
mm1 2
0
mm kN kNm kN kNm mm mm2 mm kN kN kN kN kN kN #.# mm2/mm
4900 -108 11.02 0 0 844 654.72 500 0 0 0 2119.59 0 0 0 -0.9
-0.959
Spacing of Sets Minimum Legs Shear Comments -1.8
2 legs 4 legs 6 legs Min legs
H10 H10 H10 H10 -2.7
mm mm mm mm # A
-3.6 5212
346.9 600 600 346.9 2 Minimum Steel 0 5000mm
346.9 600 600 346.9 2 Minimum Steel
346.9 600 600 346.9 2 Minimum Steel Total Long Term
346.9 600 600 346.9 2 Minimum Steel
346.9 600 600 346.9 2 Minimum Steel mm1 2
346.9 600 600 346.9 2 Minimum Steel 0
346.9 600 600 346.9 2 Minimum Steel
346.9 600 600 346.9 2 Minimum Steel -0.9
346.9 600 600 346.9 2 Minimum Steel
-1.24
346.9 600 600 346.9 2 Minimum Steel -1.8
346.9 600 600 346.9 2 Minimum Steel
346.9 600 600 346.9 2 Minimum Steel -2.7
346.9 600 600 346.9 2 Minimum Steel
-3.6 4039
0 5000mm
Detailed Reinforcement
Punching Span 1
Column Head Critical Section Top Reinforcement Bottom Reinforcement
Column Bh a at u d fcv P/A Asw/s min V* Mv* V*eff VRd1 VRd2 Asv result
No. Max Max Section Max Max Section
A #.# mm mm mm mm MPa MPa mm2/mm kN kNm kN kN kN mm2 A Locat Size Space Area Depth Width Rebar Reqd Size Space Area Depth Width Rebar Reqd
1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Check Not Requested! mm mm mm mm2 mm mm A mm mm mm2 mm mm A
2 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Check Not Requested! 100 0 0 0 56 500 No Steel Added 25 300 654.72 844 500 3 H20 @ 190
306 0 0 0 56 500 No Steel Added 25 300 654.72 844 500 3 H20 @ 190
512 0 0 0 56 500 No Steel Added 25 300 654.72 844 500 3 H20 @ 190
720 0 0 0 56 500 No Steel Added 25 300 654.72 844 500 3 H20 @ 190
896 0 0 0 56 500 No Steel Added 25 300 654.72 844 500 3 H20 @ 190
Deflections 1072 0 0 0 56 500 No Steel Added 25 300 654.72 844 500 3 H20 @ 190
All Spans Loaded 1250 0 0 0 56 500 No Steel Added 25 300 654.72 844 500 3 H20 @ 190
Transfer 1666 0 0 0 56 500 No Steel Added 25 211.4 654.72 844 500 3 H20 @ 190
2082 0 0 0 56 500 No Steel Added 16 193.8 654.72 844 500 3 H20 @ 190
mm1 2 2500 0 0 0 56 500 No Steel Added 16 187.8 654.72 844 500 3 H20 @ 190
0 2918 0 0 0 56 500 No Steel Added 16 193.8 654.72 844 500 3 H20 @ 190
3334 0 0 0 56 500 No Steel Added 25 211.4 654.72 844 500 3 H20 @ 190
-0.293
-0.9 3750 0 0 0 56 500 No Steel Added 25 300 654.72 844 500 3 H20 @ 190
3928 0 0 0 56 500 No Steel Added 25 300 654.72 844 500 3 H20 @ 190
-1.8 4104 0 0 0 56 500 No Steel Added 25 300 654.72 844 500 3 H20 @ 190
4280 0 0 0 56 500 No Steel Added 25 300 654.72 844 500 3 H20 @ 190
-2.7 4488 0 0 0 56 500 No Steel Added 25 300 654.72 844 500 3 H20 @ 190
4694 0 0 0 56 500 No Steel Added 25 300 654.72 844 500 3 H20 @ 190
17084 4900 0 0 0 56 500 No Steel Added 25 300 654.72 844 500 3 H20 @ 190
-3.6
0 5000mm Shear Reinforcement
Spacing of Sets
2 legs 4 legs 6 legs Min legs Minimum Shear
Area H10 H10 H10 H10 Legs Comments
mm1 2 mm2/mm mm mm mm mm # A
0
-0.377
-0.9
0.45 346.9 600 600 346.9 2 Minimum Steel
-1.8 0.45 346.9 600 600 346.9 2 Minimum Steel
0.45 346.9 600 600 346.9 2 Minimum Steel
-2.7 0.45 346.9 600 600 346.9 2 Minimum Steel
0.45 346.9 600 600 346.9 2 Minimum Steel
13268 0.45 346.9 600 600 346.9 2 Minimum Steel
-3.6
0 5000mm 0.45 346.9 600 600 346.9 2 Minimum Steel
0.45 346.9 600 600 346.9 2 Minimum Steel
RAPT 6.6.8.0 Project Name: J110 Page 13/13
Licensee: AECOM Singapore Pte Ltd 1/6/2022 7:52:22 PM License No.: 10479063400712WPN11
Frame Description: G/8/B/3-1a
Shear Reinforcement
Spacing of Sets
2 legs 4 legs 6 legs Min legs Minimum Shear
Area H10 H10 H10 H10 Legs Comments
mm2/mm mm mm mm mm # A
0.45 346.9 600 600 346.9 2 Minimum Steel
0.45 346.9 600 600 346.9 2 Minimum Steel
0.45 346.9 600 600 346.9 2 Minimum Steel
0.45 346.9 600 600 346.9 2 Minimum Steel
0.45 346.9 600 600 346.9 2 Minimum Steel
Design Comments:-
- SPAN Reinforcing Bar spacing - Span 1 - Smallest preferred reinforcement size requires bar spacing larger than maximum. It will be necessary to use
smaller bars than the preferred minimum size or a larger area of reinforcement than is required by design.
- - Span 1 - Required Bar Size is smaller than the Preferred Bar Size. Maintaining the same cover will require slightly less reinforcement than calculated.
- Span - 1 - Reinforcement added at left span contraflexure point for Offset of Bending Moment Diagram for Shear - 323.33mm2
- Span - 1 - Reinforcement added at right span contraflexure point for Offset of Bending Moment Diagram for Shear - 323.33mm2
Reinforcement Layout
1 2
mm
0
-200
-400
-600
-800
3-H20
0 5000mm
- SPAN Reinforcing Bar spacing - Span 1 - Smallest preferred reinforcement size requires bar spacing larger than maximum. It will be necessary to use
smaller bars than the preferred minimum size or a larger area of reinforcement than is required by design.
- - Span 1 - Required Bar Size is smaller than the Preferred Bar Size. Maintaining the same cover will require slightly less reinforcement than calculated.
Design Comments:-
- Span - 1 - Reinforcement added at left span contraflexure point for Offset of Bending Moment Diagram for Shear - 323.33mm2
- Span - 1 - Reinforcement added at right span contraflexure point for Offset of Bending Moment Diagram for Shear - 323.33mm2
RAPT 6.6.8.0 Project Name: J110 Page 2/13
Licensee: AECOM Singapore Pte Ltd 1/6/2022 7:50:15 PM License No.: 10479063400712WPN11
Frame Description: G/8A/B-7
Project Name: J110 Beams
Frame Description: G/8A/B-7 Beam Beam Beam Beam Effective
Designer: SLT Number Depth Width Width Flange
C:\Users\sujeevanleonard.tham\OneDrive - AECOM\Projects\J110\J110\OneDrive_2021-07-01\12. Southern at Width
Slab
Staircase\Design Files\Str\Beams\G,8A.B-7.rpf mm mm mm mm
1 900 750 750 750
RAPT - Version: 6.6.8.0
Reinforced And Post-Tensioned Concrete Analysis & Design Package
Copyright(C) 1988 - 2021 PCDC Pty. Ltd. All Rights Reserved
Load Cases
Load Load Type Load Definition Live Load Description
Licensee Case Deflection Case
AECOM Singapore Pte Ltd
300 Beach Road List List Y/N A
#03-00 The Concourse 1 Self Weight Applied Loads
Singapore 199555 2 Extra Dead Load Applied Loads
10479063400712WPN11 3 Live Load Applied Loads Y
Limit Reinforcement Strain Y/N Y Nominal Bar Bar Area Bar Bar Stock
Include Strain Hardening of Reinforcement Y/N N Bar Size Diameter Inertia Weight Length
Beam Shear Critical Section Location List Code Critical Section A mm mm2 mm4 kg/m mm
13 13 132.7 1402.55 1.04 12000
16 16 201.1 3218.29 1.58 12000
20 20 314.2 7857.14 2.47 12000
Maximum Service Stress Change - Prestressed Sections MPa 200
22 22 380.1 11503.6 2.98 12000
Maximum Service Stress Change - Reinforced Sections MPa 200
25 25 490.9 19182.5 3.85 12000
Relative Humidity % 50
32 32 804.2 51492.6 6.31 12000
Average Temperature C. 20
40 40 1256.6 1.257e5 9.86 12000
Prestress Losses Calculations based on List Program Default
Crack Width Calculations List .20 mm
AS3600 Shrinkage and Temperature Reinforcement List Moderate Elevation view
Degree of Restraint in Primary Direction % 0
Degree of Restraint in Secondary Direction % 0 1 2
mm
Concrete Strength Gain Rate List N 0
Concrete Tensile Strength for Deflection Calculations- #.## x (Fc)n #.# -1 -200
Maximum Value of Ieff/Igross for Deflection Calculations #.# 0.6 -400
Total Deflection Warning Limit - Maximum Span/Deflection #.# 250
Total Deflection Warning Limit - Maximum Deflection mm 40 -600
Incremental Deflection Warning Limit - Maximum Span/Deflection #.# 360
mm -800
Incremental Deflection Warning Limit - Maximum Deflection 25
Initial Time for Shrinkage List Full Shrinkage
0 10600mm
Time of Loading in days #.# 10
Age Adjustment Factor #.# 0.76
Plan view
Concrete Strength at Time of Loading MPa 27.04
Loaded Period in years #.# 30 1 2
Tension stiffening Approach List Modified Concrete Tensile Modulus Method mm
-800
Live Load Pattern Factor #.#
-400
Pattern Live Load for Ultimate Strength Y/N
Pattern Live Load for Crack Control Y/N
0
Pattern Live Load For Deflections Y/N
Pattern Live Load for Deflection Permanent Load Combination Y/N 400
0.147
-0.16
-100 28.7 28.7
0 0 10600mm
100
200 Neutral Axis Depth Initial Final
300
400
500
600
700
800 674
900
0 10600mm
Gross Stress Top Gross Stress Bottom Cracked Compression Reinforcement Tension Limits Gross Stress Top Gross Stress Bottom Cracked Compression Reinforcement Tension Limits
1 2 1 2
MPa MPa MPa MPa
-6 -4.49 -180 -5.07
-6 -400
-4 -120
-2 -60 -3 -200
0 0 0 0
2 60 3 200
4 120 6 400
6 180
9 600
8 240
10 4.7 300 12 5.3 800
0 10600mm 0 10600mm
Gross Stress Top Gross Stress Bottom Cracked Compression Reinforcement Tension Limits Gross Stress Top Gross Stress Bottom Cracked Compression Reinforcement Tension Limits
Span 1
Design Comments:-
Shear Design
- Increase in stress from decompression to working exceeds 200MPa in at least one steel layer. Reinforcement has been added to reduce stress change Beam
below this maximum value. Refer RAPT manual Section T.7.6 Span 1
Locat V* Mv* Pv Mdec d Ast bv phi Vuc phi Vut phi Vu Phi Vumax phi VuMin phi Vus Theta Asv/s
-20
-25.3
-40
Punching
Column Head Critical Section
Column Bh a at u d fcv P/A Asw/s min V* Mv* V*eff VRd1 VRd2 Asv result -60
No. 420
A #.# mm mm mm mm MPa MPa mm2/mm kN kNm kN kN kN mm2 A 0 10600mm
1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Check Not Carried Out!
2 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Check Not Carried Out!
Detailed Reinforcement
Span 1
Top Reinforcement Bottom Reinforcement
Design Comments:-
- - Span 1 - Required Bar Size is smaller than the Preferred Bar Size. Maintaining the same cover will require slightly less reinforcement than calculated.
- Span - 1 - Reinforcement added at left span contraflexure point for Offset of Bending Moment Diagram for Shear - 834.3mm2
- Span - 1 - Reinforcement added at right span contraflexure point for Offset of Bending Moment Diagram for Shear - 834.3mm2
Reinforcement Layout
1 2
mm
0
-200
-400
-600
-800
7-H25
0 10600mm
- - Span 1 - Required Bar Size is smaller than the Preferred Bar Size. Maintaining the same cover will require slightly less reinforcement than calculated.
Design Comments:-
- Span - 1 - Reinforcement added at left span contraflexure point for Offset of Bending Moment Diagram for Shear - 834.3mm2
- Span - 1 - Reinforcement added at right span contraflexure point for Offset of Bending Moment Diagram for Shear - 834.3mm2
RAPT 6.6.8.0 Project Name: J110 Page 2/17
Licensee: AECOM Singapore Pte Ltd 1/6/2022 7:46:48 PM License No.: 10479063400712WPN11
Frame Description: G/A/8/1-3, G/A/8/1-1
Project Name: J110 Beams
Frame Description: G/A/8/1-3, G/A/8/1-1 Beam Beam Beam Beam Effective
Designer: SLT Number Depth Width Width Flange
C:\Users\sujeevanleonard.tham\OneDrive - AECOM\Projects\J110\J110\OneDrive_2021-07-01\12. Southern at Width
Slab
Staircase\Design Files\Str\Beams\G,A,8,1-3, G,A,8,1-1.rpf mm mm mm mm
1 600 300 300 300
RAPT - Version: 6.6.8.0 RC 600 300 300 300
Reinforced And Post-Tensioned Concrete Analysis & Design Package
Copyright(C) 1988 - 2021 PCDC Pty. Ltd. All Rights Reserved
Load Cases
Licensee Load Load Type Load Definition Live Load Description
AECOM Singapore Pte Ltd Case Deflection Case
300 Beach Road
#03-00 The Concourse List List Y/N A
Singapore 199555 1 Self Weight Applied Loads
10479063400712WPN11 2 Extra Dead Load Applied Loads
3 Live Load Applied Loads Y
Due to the different Concrete Strength types in the Design Standard and Materials in this run, the concrete strengths shown in the materials data have been Load Combinations : Ultimate
multiplied in the calculatiuons by 0.8 Load Description 1. Self 2. Extra 3.
Combination Weight Dead Live
Span Load Load
A #.# #.# #.#
Span Span Slab Panel Panel
Length Depth Width Width 1 Live Load 1.35 1.35 1.5
Left Right 2 Live Load 1 1 1.5
mm mm mm mm 3 Dead Load 1.425 1.425 0
LE 0
1 3000 200 2000 2000
RC 2100 200 2000 2000 Load Combinations : Short Term Service
Load Description 1. Self 2. Extra 3. Live
Combination Weight Dead Load Load
Columns A #.# #.# #.#
Column Column Support Transverse Transverse 1 Live Load 1 1 0.5
Grid Type Column prestress
Reference spacing (P/A)
A List mm MPa
Load Combinations : Permanent Service
1 1 Knife-Edge 2000
Load Description 1. Self 2. Extra 3. Live
2 2 Knife-Edge 2000 Combination Weight Dead Load Load
A #.# #.# #.#
1 Live Load 1 1 0.3
RAPT 6.6.8.0 Project Name: J110 Page 3/17 RAPT 6.6.8.0 Project Name: J110 Page 4/17
Licensee: AECOM Singapore Pte Ltd 1/6/2022 7:46:51 PM License No.: 10479063400712WPN11 Licensee: AECOM Singapore Pte Ltd 1/6/2022 7:46:55 PM License No.: 10479063400712WPN11
Frame Description: G/A/8/1-3, G/A/8/1-1 Frame Description: G/A/8/1-3, G/A/8/1-1
Load Combinations : Deflection Reinforcement
Load Description 1. Self 2. Extra 3. Live Maximum Minimum Minimum Minimum Span Minimum Span Infill Stagger
Combination Weight Dead Load Load Bar Bar Continuous Reinforcement Reinforcement Bars Bars
A #.# #.# #.# Spacing Spacing Reinforcement into End into Internal
1 Short Term - Deflection 1 1 0.5 Support Support
2 Permanent - Deflection 1 1 0.3 mm mm #.# #.# #.# Y/N Y/N
3 Initial - Deflection 1 0 0 Support Reinforcement 300 60 0 N N
Span Reinforcement 300 60 0 0 N N
Limit Reinforcement Strain Y/N Y Nominal Bar Bar Area Bar Bar Stock
Include Strain Hardening of Reinforcement Y/N N Bar Size Diameter Inertia Weight Length
Beam Shear Critical Section Location List Code Critical Section A mm mm2 mm4 kg/m mm
13 13 132.7 1402.55 1.04 12000
16 16 201.1 3218.29 1.58 12000
20 20 314.2 7857.14 2.47 12000
Maximum Service Stress Change - Prestressed Sections MPa 150
22 22 380.1 11503.6 2.98 12000
Maximum Service Stress Change - Reinforced Sections MPa 0
25 25 490.9 19182.5 3.85 12000
Relative Humidity % 50
32 32 804.2 51492.6 6.31 12000
Average Temperature C. 20
40 40 1256.6 1.257e5 9.86 12000
Prestress Losses Calculations based on List Program Default
Crack Width Calculations List Code default
AS3600 Shrinkage and Temperature Reinforcement List Moderate Elevation view
Degree of Restraint in Primary Direction % 0
Degree of Restraint in Secondary Direction % 0 1 2
mm
Concrete Strength Gain Rate List N 0
0.069
0.069
-120 0.08
0 3000mm
0.06
Shear Shear 1 Shear 2 0.04
0.02
0
Shear -0.02
-0.04
1 2
kNm -0.06
0.053
-100 -86.6 -86.6
0 3000mm
-80
-60 Neutral Axis Depth Initial Final
-40
-20 Span 1
3.91 Design Comments:-
0
- As there is no area of steel in the tension zone (any prestressing tendons are in the compression zone) we are now adding an area of steel, equivalent to
20 that required for minimum reinforcement, to the design tension layer. This is then assumed to be the initial design reinforcement setup. More reinforcement will
17
40 be added as required to achieve the applied moments. Ast added = 242.23mm2 @ 1000mm
0 3000mm
Gross Stress Top Gross Stress Bottom Cracked Compression Reinforcement Tension Gross Stress Top Gross Stress Bottom Cracked Compression Reinforcement Tension
1 2 1 2
MPa MPa
MPa MPa
-4 -2.13 -2.13 -400 -2.13 -2.13
-4 -400
-2 -200 -2 -200
0 0 0 0
2 200 2 200
4 400
4 400
6 600
6 600 8 800
8 2.17 2.17 800 10 2.17 2.17 1000
0 3000mm 0 3000mm
Gross Stress Top Gross Stress Bottom Cracked Compression Reinforcement Tension Gross Stress Top Gross Stress Bottom Cracked Compression Reinforcement Tension
-9
mm kN kNm kN kNm mm mm2 mm kN kN kN kN kN kN #.# mm2/mm
1 82.49 -86.57 0 0 544 378.02 300 0 0 0 819.71 0 0 0 -12 71595 3590
480 63.67 -51.57 0 0 544 271.17 300 65.78 99999 65.78 819.71 144.51 0 21.8 0.27 0 3000mm
525 61.9 -48.74 0 0 544 271.17 300 65.78 99999 65.78 819.71 144.51 0 21.8 0.27
700 55.02 -38.51 0 0 544 271.17 300 65.78 99999 65.78 819.71 144.51 0 21.8 0.27 Short Term
875 48.14 -29.49 0 0 544 271.17 300 65.78 99999 65.78 819.71 144.51 0 21.8 0.27
1050 41.26 -21.66 0 0 544 271.17 300 65.78 99999 65.78 819.71 144.51 0 21.8 0.27 1 2
mm
1225 34.39 -15.04 0 0 544 271.17 300 65.78 99999 65.78 819.71 144.51 0 21.8 0.27
0
1400 27.51 -9.63 0 0 544 271.17 300 65.78 99999 65.78 819.71 144.51 0 21.8 0.27 0.077
1575 20.63 -5.42 0 0 544 271.17 300 65.78 99999 65.78 819.71 144.51 0 21.8 0.27 -3 -1.47
1718 15.01 -2.87 0 0 544 271.17 300 65.78 99999 65.78 819.71 144.51 0 21.8 0.27
1859 9.47 -1.14 0 0 544 271.17 300 65.78 99999 65.78 819.71 144.51 0 21.8 0.27 -6
2000 3.93 -0.2 0 0 544 271.17 300 65.78 99999 65.78 819.71 144.51 0 21.8 0.27
-9
Spacing of Sets Minimum Legs Shear Comments
2 legs 4 legs 6 legs Min legs -12 39022 1431
H10 H10 H10 H10 0 3000mm
mm mm mm mm # A
Even Spans Loaded Odd Spans Loaded All Spans Loaded
408 408 408 408 2 Minimum Steel
408 408 408 408 2 Minimum Steel Incremental
408 408 408 408 2 Minimum Steel
1 2
408 408 408 408 2 Minimum Steel mm
408 408 408 408 2 Minimum Steel 0
0.203
408 408 408 408 2 Minimum Steel
408 408 408 408 2 Minimum Steel -3
408 408 408 408 2 Minimum Steel -3.53
408 408 408 408 2 Minimum Steel -6
408 408 408 408 2 Minimum Steel
408 408 408 408 2 Minimum Steel -9
-9
-6 -6
-9 -9
1 2 1 2
mm mm
0 0
0.118 -0.03
-0.665
-3 -1.66 -3
-6 -6
-9 -9
All Spans Loaded Odd Spans Loaded Even Spans Loaded All Spans Loaded Even Spans Loaded Odd Spans Loaded
Incremental Incremental
1 2 1 2
mm mm
0 0
0.243 0.149
-3 -3
-2.71
-3.7
-6 -6
-9 -9
All Spans Loaded Odd Spans Loaded Even Spans Loaded All Spans Loaded Even Spans Loaded Odd Spans Loaded
1 2 1 2
mm mm
0 0
0.283 0.188
-3 -3
-3.26
-6 -4.26 -6
-9 -9
All Spans Loaded Odd Spans Loaded Even Spans Loaded All Spans Loaded Even Spans Loaded Odd Spans Loaded
Detailed Reinforcement
Span 1
Top Reinforcement Bottom Reinforcement
Max Max Section Max Max Section Max Max Section Max Max Section
Locat Size Space Area Depth Width Rebar Reqd Size Space Area Depth Width Rebar Reqd Locat Size Space Area Depth Width Rebar Reqd Size Space Area Depth Width Rebar Reqd
mm mm mm mm2 mm mm A mm mm mm2 mm mm A mm mm mm mm2 mm mm A mm mm mm2 mm mm A
226 0 0 0 56 300 No Steel Added 32 300 271.17 544 300 1 H20 @ 999 409 16 208.1 376.84 56 300 2 H20 @ 195 0 0 0 544 300 No Steel Added
352 0 0 271.04 56 300 1 H20 @ 999 32 300 271.17 544 300 1 H20 @ 999 480 16 232.2 376.84 56 300 2 H20 @ 195 0 0 0 544 300 No Steel Added
480 0 0 271.04 56 300 1 H20 @ 999 32 300 271.17 544 300 1 H20 @ 999 525 16 247.3 376.84 56 300 2 H20 @ 195 0 0 0 544 300 No Steel Added
615 0 0 271.04 56 300 1 H20 @ 999 32 300 271.17 544 300 1 H20 @ 999 700 32 300 324.56 56 300 2 H20 @ 195 0 0 0 544 300 No Steel Added
750 0 0 271.04 56 300 1 H20 @ 999 32 300 271.17 544 300 1 H20 @ 999 875 32 300 271.17 56 300 1 H20 @ 999 0 0 0 544 300 No Steel Added
1000 0 0 271.04 56 300 1 H20 @ 999 32 300 271.17 544 300 1 H20 @ 999 1050 32 300 271.17 56 300 1 H20 @ 999 0 0 0 544 300 No Steel Added
1250 32 300 271.04 56 300 1 H20 @ 999 32 300 271.17 544 300 1 H20 @ 999 1225 32 300 271.17 56 300 1 H20 @ 999 0 0 0 544 300 No Steel Added
1500 32 300 271.04 56 300 1 H20 @ 999 32 300 271.17 544 300 1 H20 @ 999 1400 32 300 271.17 56 300 1 H20 @ 999 0 0 0 544 300 No Steel Added
1750 32 300 271.17 56 300 1 H20 @ 999 32 300 271.04 544 300 1 H20 @ 999 1575 32 300 271.17 56 300 1 H20 @ 999 0 0 0 544 300 No Steel Added
2000 32 300 288.18 56 300 1 H20 @ 999 0 0 271.04 544 300 1 H20 @ 999 1718 32 300 271.17 56 300 1 H20 @ 999 0 0 0 544 300 No Steel Added
2250 25 297.6 364.02 56 300 2 H20 @ 195 0 0 0 544 300 No Steel Added 1859 32 300 271.17 56 300 1 H20 @ 999 0 0 0 544 300 No Steel Added
2385 25 259.8 376.92 56 300 2 H20 @ 195 0 0 0 544 300 No Steel Added 2000 32 300 271.17 56 300 1 H20 @ 999 0 0 0 544 300 No Steel Added
2520 16 218.6 376.92 56 300 2 H20 @ 195 0 0 0 544 300 No Steel Added Shear Reinforcement
2550 16 209.1 376.92 56 300 2 H20 @ 195 0 0 0 544 300 No Steel Added Spacing of Sets
2663 12 189.2 376.92 56 300 2 H20 @ 195 0 0 0 544 300 No Steel Added 2 legs 4 legs 6 legs Min legs Minimum Shear
2775 12 184.1 376.92 56 300 2 H20 @ 195 0 0 0 544 300 No Steel Added Area H10 H10 H10 H10 Legs Comments
2887 12 180.7 376.92 56 300 2 H20 @ 195 0 0 0 544 300 No Steel Added mm2/mm mm mm mm mm # A
2999 12 176.3 378.1 56 300 2 H20 @ 195 0 0 0 544 300 No Steel Added
Shear Reinforcement
Spacing of Sets
2 legs 4 legs 6 legs Min legs Minimum Shear
Area H10 H10 H10 H10 Legs Comments
mm2/mm mm mm mm mm # A
2-H20
- - Column Grid 2 - Required Bar Size is smaller than the Preferred Bar Size. Maintaining the same cover will require slightly less reinforcement than mm
calculated. 0
- SPAN Reinforcing Bar spacing - Span 1 - Smallest preferred reinforcement size requires bar spacing larger than maximum. It will be necessary to use
smaller bars than the preferred minimum size or a larger area of reinforcement than is required by design.
- - Span 1 - Required Bar Size is smaller than the Preferred Bar Size. Maintaining the same cover will require slightly less reinforcement than calculated. -200
- Span - 1 - Reinforcement added at right support contraflexure point for Offset of Bending Moment Diagram for Shear - 7.19mm2
- Span - 1 - Reinforcement added at left span contraflexure point for Offset of Bending Moment Diagram for Shear - 92.61mm2
- Span - 1 - Reinforcement added at right span contraflexure point for Offset of Bending Moment Diagram for Shear - 92.61mm2 -400
1-H20
Span 2 -600
Top Reinforcement Bottom Reinforcement 0 3000mm
- SUPPORT Reinforcing Bar Spacing - Column Grid 2 - Smallest preferred reinforcement size requires bar spacing larger than maximum. It will be
necessary to use smaller bars than the preferred minimum size or a larger area of reinforcement than is required by design.
- - Column Grid 2 - Required Bar Size is smaller than the Preferred Bar Size. Maintaining the same cover will require slightly less reinforcement than
calculated.
RAPT 6.6.8.0 Project Name: J110 Page 2/18
Licensee: AECOM Singapore Pte Ltd 1/6/2022 7:43:21 PM License No.: 10479063400712WPN11
Frame Description: G/A/8/3, G/A/8/4
Project Name: J110 Beams
Frame Description: G/A/8/3, G/A/8/4 Beam Beam Beam Beam Effective
Designer: SLT Number Depth Width Width Flange
C:\Users\sujeevanleonard.tham\OneDrive - AECOM\Projects\J110\J110\OneDrive_2021-07-01\12. Southern at Width
Slab
Staircase\Design Files\Str\Beams\G,A,8,3, G,A,8,4.rpf mm mm mm mm
1 900 750 750 2110
RAPT - Version: 6.6.8.0 RC 900 750 750 750
Reinforced And Post-Tensioned Concrete Analysis & Design Package
Copyright(C) 1988 - 2021 PCDC Pty. Ltd. All Rights Reserved
Elements : Trapezoidal
Licensee Element Description Solid/Void Depth Element Width Width Width Width Left End Distance to Left Right End Distance to Right Number
AECOM Singapore Pte Ltd Top Depth Top Top Bottom Bottom Reference End from Left Reference End from Right of
300 Beach Road Left Right Left Right Column Reference Column Reference Elements
#03-00 The Concourse Column Column in Group
Singapore 199555 A List mm mm mm mm mm mm # mm # mm #
10479063400712WPN11 1 new element -5000 5000 125 125 125 125 1 2400 1 5600 1
Span
Span Span Slab Panel Panel 2. Initial Dead Load - Line
Length Depth Width Width Load Left End Left end of Load Right Right end of Load Description
Left Right Reference load from at left End load from at right
mm mm mm mm Column reference end reference reference end
LE 0 column column column
# mm kN/m # mm kN/m A
1 8000 350 2800 2800
RC 2800 350 750 750 1 1 2400 105 1 5700 105 SLAB SW FROM UPPER FLOORS
2 2 0 14 2 2800 14 SLAB SELFWEIGH (11.55 LEVEL)
Columns
Column Column Support Transverse Transverse 3. Extra Dead Load - Line
Grid Type Column prestress Load Left End Left end of Load Right Right end of Load Description
Reference spacing (P/A) Reference load from at left End load from at right
A List mm MPa Column reference end reference reference end
1 1 Knife-Edge 2800 column column column
# mm kN/m # mm kN/m A
2 2 Knife-Edge 1775
1 1 2400 51 1 5700 51 SDL=3 KPA, 2.8M SPAN WIDTH, 6FLOORS
2 2 0 8.4 2 2800 8.4 SDL=3 KPA, 2.8M SPAN WIDTH
RAPT 6.6.8.0 Project Name: J110 Page 3/18 RAPT 6.6.8.0 Project Name: J110 Page 4/18
Licensee: AECOM Singapore Pte Ltd 1/6/2022 7:43:25 PM License No.: 10479063400712WPN11 Licensee: AECOM Singapore Pte Ltd 1/6/2022 7:43:28 PM License No.: 10479063400712WPN11
Frame Description: G/A/8/3, G/A/8/4 Frame Description: G/A/8/3, G/A/8/4
3. Extra Dead Load - Panel Load Combinations : Pre Existing
Load Left End Left end of Load at Right Right end of Load at Description Load Description 1. Self 2. Initial 3. Extra 4. Live
reference load from left end End load from right Combination Weight Dead Load Dead Load Load
column reference reference reference end A #.# #.# #.# #.#
column column column 1 Pre Existing 1 0 0 0
# mm kN/m2 # mm kN/m2 A
1 1 0 3.5 2 0 3.5 SDL=3.5 KPA
Load Combinations : Short Term Service Load Case 3 : 3. Extra Dead Load
Load Description 1. Self 2. Initial 3. Extra 4. Live
Combination Weight Dead Load Dead Load Load
A #.# #.# #.# #.# kN/m1 2
Material Properties
Reinforcement Design Zones Concrete : Standard Concrete : Concrete Strength Basis - Cube
Description A C32/40MPa
1 2 Characteristic Compressive Strength MPa 40
Mean Compressive Strength MPa 50
mm Lower Characteristic Tensile Strength MPa 2.12
4000 Upper Characteristic Tensile Strength MPa 3.93
Concrete Density kg/m3 2447
2000 Design Concrete Modulus MPa 31186.6
Mean Concrete Modulus MPa 33345.8
Basic Shrinkage Strain mm/mm 0
0
Shrinkage Multiplier #.# 1
Basic Creep Factor #.# 2.656
0 8000mm Creep Multiplier #.# 1
Design Data Concrete Strain at Peak Stress #.# 0.002
Capacity Reduction factor (phi) for Flexure #.# 1 Squash Load Factor #.# 0.85
Capacity Reduction factor (phi) for Shear #.# 1 Concrete Strain Limit #.# 0.004
Capacity Reduction factor (phi) for Shear with transverse reinf #.# 1 Strength Gain Rate List Normal
Material Factor for Concrete in Flexure #.# 1.5 Maximum Aggregate Size mm 20
Material Factor for Concrete in Shear #.# 1.5
Material Factor for Reinforcement #.# 1.15
RAPT 6.6.8.0 Project Name: J110 Page 7/18 RAPT 6.6.8.0 Project Name: J110 Page 8/18
Licensee: AECOM Singapore Pte Ltd 1/6/2022 7:43:38 PM License No.: 10479063400712WPN11 Licensee: AECOM Singapore Pte Ltd 1/6/2022 7:43:41 PM License No.: 10479063400712WPN11
Frame Description: G/A/8/3, G/A/8/4 Frame Description: G/A/8/3, G/A/8/4
Reinforcement Bar Col No. 2 Self Initial Extra Live Load
Designation Type Yield Elastic Ductility Peak Peak Design Material Material Material Capacity Material Capacity Include as Description Weight Dead Dead
Stress Modulus Strain Stress Strain Factor Factor Reduction Factor Reduction Factor Flexural Load Load
Limit Flexure Shear - Flexure - Shear Reinforcement for Moment Above kNm -0 -0 -0 -0
Shear Moment Below kNm -0 -0 -0 -0
H Deformed 500 2.05e5 N 0.05 540 90 -1 -1 -1 -1 Y Reaction kN 375.81 221.48 152.04 242.39
Elastic Rotation #.# -2.85e-4 -1.72e-4 -1.17e-4 -1.84e-4
Elastic Axial Shortening mm 0 0 0 0
Nominal Bar Bar Area Bar Bar Stock
Bar Size Diameter Inertia Weight Length
A mm mm2 mm4 kg/m mm
10 10 78.5 491.07 0.62 12000
Load Combinations
13 13 132.7 1402.55 1.04 12000 Column Actions
16 16 201.1 3218.29 1.58 12000 Col No. 1 Characteristic Characteristic Service Service Ultimate Ultimate Ultimate Ultimate
20 20 314.2 7857.14 2.47 12000 Service Service (Reversal) Flexure Flexure Shear Shear
(Reversal) (Reversal) (Reversal)
22 22 380.1 11503.6 2.98 12000 kNm
Moment Above 0 0 0 0 0 0 0 0
25 25 490.9 19182.5 3.85 12000 kNm
Moment Below 0 0 0 0 0 0 0 0
32 32 804.2 51492.6 6.31 12000 kN
Reaction 767.96 767.96 674.95 674.95 1064.64 1064.64 571.66 1074.93
40 40 1256.6 1.257e5 9.86 12000 #.#
Elastic Rotation 8.66e-4 8.66e-4 7.61e-4 7.61e-4 1.2e-3 1.2e-3 6.36e-4 1.22e-3
Elastic Axial Shortening mm 0 0 0 0 0 0 0 0
Elevation view
Col No. 2 Characteristic Characteristic Service Service Ultimate Ultimate Ultimate Ultimate
1 2 Service Service (Reversal) Flexure Flexure Shear Shear
(Reversal) (Reversal) (Reversal)
mm Moment Above kNm 0 0 0 0 0 0 0 0
4000 Moment Below kNm 0 0 0 0 0 0 0 0
Reaction kN 991.71 991.71 870.52 870.52 1375.17 1375.17 818.41 1375.17
2000 Elastic Rotation #.# -7.58e-4 -7.58e-4 -6.66e-4 -6.66e-4 -1.05e-3 -1.05e-3 -5.11e-4 -1.05e-3
Elastic Axial Shortening mm 0 0 0 0 0 0 0 0
0.103
1 2
0.052
0.12
kNm
-305 -305 0.08
-500 107
0 0.04
500 0
1000
-0.04
1500
2000 -0.08
2500 -0.12
0.116
3000 2573 -0.16
3500 0 8000mm
0 8000mm
Neutral Axis Depth Initial Final
Moment Moment 1 Moment 2
Span 1
Design Comments:-
1 2 - As there is no area of steel in the tension zone (any prestressing tendons are in the compression zone) we are now adding an area of steel, equivalent to
kN that required for minimum reinforcement, to the design tension layer. This is then assumed to be the initial design reinforcement setup. More reinforcement will
1200 1016 be added as required to achieve the applied moments. Ast added = 1889.91mm2 @ 7640mm
800
400 163
0
Service
-400
Maximum Moment Condition
-800
-1200 1 2
-1096
-1600 MPa MPa
0 8000mm -12 -10.08 -1.86 -280
-9 -210
Shear Shear 1 Shear 2 -6 -140
-3 -70
0 0
Flexural Design 3 70
Ultimate 6 140
9 210
1 2 12 6.48 1.88 280
mm20 2163 0 8000mm
2000
Gross Stress Top Gross Stress Bottom Cracked Compression Reinforcement Tension
0
-2000 Reversal Moment Condition
-4000
1 2
-6000 MPa MPa
-12 -8.59 -1.59 -280
-8000 6900 0 -9 -210
0 8000mm -6 -140
-3 -70
Reinforcement Top Total Bottom Total Top Ultimate Bottom Ultimate Min Top Min Bot 0 0
3 70
6 140
1 2
kNm 9 210
-2000 12 5.52 1.62 280
0 0 8000mm
2000
4000 Gross Stress Top Gross Stress Bottom Cracked Compression Reinforcement Tension
6000
8000
10000 Permanent
12000
14000
0 8000mm 1 2
MPa MPa
-12 -9.51 -1.75 -240
Capacity Minimum Ultimate Design Initial Final -9 -180
-6 -120
-3 -60
0 0
3 60
6 120
9 180
12 6.11 1.78 240
0 8000mm
RAPT 6.6.8.0 Project Name: J110 Page 11/18 RAPT 6.6.8.0 Project Name: J110 Page 12/18
Licensee: AECOM Singapore Pte Ltd 1/6/2022 7:43:51 PM License No.: 10479063400712WPN11 Licensee: AECOM Singapore Pte Ltd 1/6/2022 7:43:55 PM License No.: 10479063400712WPN11
Frame Description: G/A/8/3, G/A/8/4 Frame Description: G/A/8/3, G/A/8/4
Reversal Moment Condition
Locat V* Mv* Pv Mdec d Ast bv phi Vuc phi Vut phi Vu Phi Vumax phi VuMin phi Vus Theta Asv/s
1 2
MPa MPa
-12 -8.61 -1.59 -240
mm kN kNm kN kNm mm mm2 mm kN kN kN kN kN kN #.# mm2/mm
-9 -180
-6 -120 5601 -932.02 2200.23 0 0 824 6721.31 750 361.41 99999 361.41 3104.04 547.23 932.02 21.8 1.16
-3 -60 5701 -973.46 2104.94 0 0 824 6432 750 356.15 99999 356.15 3104.04 547.23 973.46 21.8 1.21
0 0 6000 -997.75 1810.24 0 0 824 5544.82 750 338.96 99999 338.96 3104.04 547.23 997.75 21.8 1.24
3 60 6268 -1015.58 1564.61 0 0 824 4737.29 750 321.63 99999 321.63 3104.04 547.23 1015.58 21.8 1.26
6 120 6534 -1037.19 1291.59 0 0 824 3939.87 750 302.47 99999 302.47 3104.04 547.23 1037.19 21.8 1.29
9 180 6800 -1058.79 1012.82 0 0 824 3127.92 750 280.07 99999 280.07 3104.04 547.23 1058.79 21.8 1.31
12 5.53 1.62 240 7280 -1096.47 504.8 0 0 824 1644.73 750 226.06 99999 226.06 3104.04 547.23 1096.47 21.8 1.36
0 8000mm 7999 -1154.87 -304.56 0 0 824 2163.47 750 0 0 0 3104.04 0 0 0
Gross Stress Top Gross Stress Bottom Cracked Compression Reinforcement Tension Spacing of Sets Minimum Legs Shear Comments
2 legs 4 legs 6 legs Min legs
H10 H10 H10 H10
Characteristic Service
mm mm mm mm # A
Maximum Moment Condition
124.5 249 373.6 186.8 3
MPa1 2 MPa
129.3 258.6 387.9 194 3
-16 -320
-11.52 -2.12 132.2 264.5 396.7 198.3 3
-12 -240
135.3 270.6 405.8 202.9 3
-8 -160 137.9 275.8 413.7 206.9 3
-4 -80 143 285.9 428.9 214.4 3
0 0 600 600 600 600 2 Minimum Steel
4 80 600 600 600 600 2 Minimum Steel
8 160 600 600 600 600 2 Minimum Steel
12 240 600 600 600 600 2 Minimum Steel
7.4 2.15
600 600 600 600 2 Minimum Steel
0 8000mm
600 600 600 600 2 Minimum Steel
Gross Stress Top Gross Stress Bottom Cracked Compression Reinforcement Tension 600 600 600 600 2 Minimum Steel
135.8 271.6 407.4 203.7 3
Reversal Moment Condition 130 260 390 195 3
126.9 253.7 380.6 190.3 3
MPa1 2 MPa 124.6 249.2 373.9 186.9 3
-16 -320 122 244.1 366.1 183 3
-8.53 -1.59
-12 -240 119.5 239.1 358.6 179.3 3
-8 -160 115.4 230.9 346.3 173.1 3
-4 -80
0 0
4 80
8 160 Span 2
12 240 Locat V* Mv* Pv Mdec d Ast bv phi Vuc phi Vut phi Vu Phi Vumax phi VuMin phi Vus Theta Asv/s
5.48 1.62
0 8000mm
mm kN kNm kN kNm mm mm2 mm kN kN kN kN kN kN #.# mm2/mm
Gross Stress Top Gross Stress Bottom Cracked Compression Reinforcement Tension
1 220.14 -305.5 0 0 824 1006.7 750 0 0 0 3104.04 0 0 0
720 163.04 -167.74 0 0 824 1006.7 750 223.14 99999 223.14 3104.04 547.23 0 21.8 0.68
Shear Design 1200 124.91 -98.64 0 0 824 1006.7 750 223.14 99999 223.14 3104.04 547.23 0 21.8 0.68
Beam 1400 109.03 -75.24 0 0 824 1006.7 750 223.14 99999 223.14 3104.04 547.23 0 21.8 0.68
Span 1 1750 81.23 -41.94 0 0 824 1006.7 750 223.14 99999 223.14 3104.04 547.23 0 21.8 0.68
Locat V* Mv* Pv Mdec d Ast bv phi Vuc phi Vut phi Vu Phi Vumax phi VuMin phi Vus Theta Asv/s 2100 53.43 -18.38 0 0 824 1006.7 750 223.14 99999 223.14 3104.04 547.23 0 21.8 0.68
2401 29.53 -5.89 0 0 824 1006.7 750 223.14 99999 223.14 3104.04 547.23 0 21.8 0.68
2700 7.4 -0.37 0 0 824 1006.7 750 223.14 99999 223.14 3104.04 547.23 0 21.8 0.68
mm kN kNm kN kNm mm mm2 mm kN kN kN kN kN kN #.# mm2/mm
100 1066.81 107.09 0 0 824 1248.78 750 0 0 0 3104.04 0 0 0 Spacing of Sets Minimum Legs Shear Comments
720 1016.45 752.9 0 0 824 2142.52 750 246.88 99999 246.88 3104.04 547.23 1016.45 21.8 1.26 2 legs 4 legs 6 legs Min legs
1200 978.77 1222.51 0 0 824 3538.28 750 291.82 99999 291.82 3104.04 547.23 978.77 21.8 1.21 H10 H10 H10 H10
1466 957.16 1479.99 0 0 824 4296.48 750 311.33 99999 311.33 3104.04 547.23 957.16 21.8 1.19 mm mm mm mm # A
1732 935.56 1731.72 0 0 824 5037.2 750 328.28 99999 328.28 3104.04 547.23 935.56 21.8 1.16
2000 917.73 1955.91 0 0 824 5800.3 750 344.09 99999 344.09 3104.04 547.23 917.73 21.8 1.14 231.3 462.6 600 346.9 3 Minimum Steel
2399 885.32 2315.61 0 0 824 6900.21 750 364.59 99999 364.59 3104.04 547.23 885.32 21.8 1.1 231.3 462.6 600 346.9 3 Minimum Steel
2401 884.67 2317.39 0 0 5824 5295.9 250 469.34 99999 469.34 7313.08 1289.26 884.67 21.8 0.23 231.3 462.6 600 346.9 3 Minimum Steel
2934 607.9 2547.01 0 0 5824 5295.9 250 469.34 99999 469.34 7313.08 1289.26 607.9 21.8 0.23 231.3 462.6 600 346.9 3 Minimum Steel
3467 318.44 2796.14 0 0 5824 5295.9 250 469.34 99999 469.34 7313.08 1289.26 0 21.8 0.23 231.3 462.6 600 346.9 3 Minimum Steel
4000 -133.67 2572.93 0 0 5824 5295.9 250 469.34 99999 469.34 7313.08 1289.26 0 21.8 0.23 231.3 462.6 600 346.9 3 Minimum Steel
4050 -154.38 2565.73 0 0 5824 5295.9 250 469.34 99999 469.34 7313.08 1289.26 0 21.8 0.23 231.3 462.6 600 346.9 3 Minimum Steel
4825 -532.4 2581.96 0 0 5824 5295.9 250 469.34 99999 469.34 7313.08 1289.26 532.4 21.8 0.23
5599 -931.04 2202.09 0 0 5824 5295.9 250 469.34 99999 469.34 7313.08 1289.26 931.04 21.8 0.23
RAPT 6.6.8.0 Project Name: J110 Page 13/18 RAPT 6.6.8.0 Project Name: J110 Page 14/18
Licensee: AECOM Singapore Pte Ltd 1/6/2022 7:43:58 PM License No.: 10479063400712WPN11 Licensee: AECOM Singapore Pte Ltd 1/6/2022 7:44:01 PM License No.: 10479063400712WPN11
Frame Description: G/A/8/3, G/A/8/4 Frame Description: G/A/8/3, G/A/8/4
Punching Total Long Term
Column Head Critical Section
Column Bh a at u d fcv P/A Asw/s min V* Mv* V*eff VRd1 VRd2 Asv result 1 2
mm
No. 30
A #.# mm mm mm mm MPa MPa mm2/mm kN kNm kN kN kN mm2 A
1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Check Not Carried Out! 20
2 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Check Not Carried Out! 10.7
10
0 -7.3
-10
Deflections -20 1096 262
All Spans Loaded 0 8000mm
Transfer
Even Spans Loaded Odd Spans Loaded All Spans Loaded
1 2
mm
30 Even Spans Loaded
Transfer
20
10 1 2
1.84 mm
-1.37 30
0
-10 20
-10 20
-10 20
All Spans Loaded Odd Spans Loaded Even Spans Loaded All Spans Loaded Even Spans Loaded Odd Spans Loaded
5-H25
0
6-H40
Design Comments:- 0 8000mm
- - Column Grid 2 - Required Bar Size is smaller than the Preferred Bar Size. Maintaining the same cover will require slightly less reinforcement than
calculated.
- SPAN Reinforcing Bar spacing - Span 1 - Largest preferred reinforcement size requires bar spacing smaller then minimum. It will be necessary to use - - Column Grid 2 - Required Bar Size is smaller than the Preferred Bar Size. Maintaining the same cover will require slightly less reinforcement than
larger bars than the preferred maximum size, place more reinforcement in the flange if possible or place reinforcement in multiple layers. calculated.
- - Span 1 - Required Bar Size is greater than the Preferred Bar Size. Maintaining the same cover will require slightly more reinforcement than calculated. - SPAN Reinforcing Bar spacing - Span 1 - Largest preferred reinforcement size requires bar spacing smaller then minimum. It will be necessary to use
RAPT has increased the required reinforcement by the ratio of the effective depths for the 2 bar sizes in the reinforcement layout. larger bars than the preferred maximum size, place more reinforcement in the flange if possible or place reinforcement in multiple layers.
- Span - 1 - Reinforcement added at right support contraflexure point for Offset of Bending Moment Diagram for Shear - 889.38mm2 - - Span 1 - Required Bar Size is greater than the Preferred Bar Size. Maintaining the same cover will require slightly more reinforcement than calculated.
- Span - 1 - Reinforcement added at left span contraflexure point for Offset of Bending Moment Diagram for Shear - 3090.41mm2 RAPT has increased the required reinforcement by the ratio of the effective depths for the 2 bar sizes in the reinforcement layout.
- Span - 1 - Reinforcement added at right span contraflexure point for Offset of Bending Moment Diagram for Shear - 3280.85mm2 Design Comments:-
- Span - 1 - Reinforcement added at left span contraflexure point for Offset of Bending Moment Diagram for Shear - 3090.41mm2
- Span - 1 - Reinforcement added at right span contraflexure point for Offset of Bending Moment Diagram for Shear - 3280.85mm2
Span 2
Top Reinforcement Bottom Reinforcement
- - Column Grid 2 - Required Bar Size is smaller than the Preferred Bar Size. Maintaining the same cover will require slightly less reinforcement than
calculated.
Max Max Section Max Max Section
Locat Size Space Area Depth Width Rebar Reqd Size Space Area Depth Width Rebar Reqd
mm mm mm mm2 mm mm A mm mm mm2 mm mm A
1 12 195.9 1006.7 76 750 3 H25 @ 320 0 0 0 824 750 No Steel Added
234 16 245.3 1006.7 76 750 3 H25 @ 320 0 0 0 824 750 No Steel Added
467 25 289.9 1006.7 76 750 3 H25 @ 320 0 0 0 824 750 No Steel Added
700 32 300 1006.7 76 750 3 H25 @ 320 0 0 0 824 750 No Steel Added
720 32 300 1006.7 76 750 3 H25 @ 320 0 0 0 824 750 No Steel Added
1200 32 300 1006.7 76 750 3 H25 @ 320 0 0 0 824 750 No Steel Added
1400 32 300 1006.7 76 750 3 H25 @ 320 0 0 0 824 750 No Steel Added
1750 32 300 1006.7 76 750 3 H25 @ 320 0 0 0 824 750 No Steel Added
2100 32 300 1006.7 76 750 3 H25 @ 320 0 0 0 824 750 No Steel Added
2401 32 300 1006.7 76 750 3 H25 @ 320 0 0 0 824 750 No Steel Added
2700 32 300 1006.7 76 750 3 H25 @ 320 0 0 0 824 750 No Steel Added
Shear Reinforcement
Spacing of Sets
2 legs 4 legs 6 legs Min legs Minimum Shear
Area H10 H10 H10 H10 Legs Comments
mm2/mm mm mm mm mm # A
Design Comments:-
- - Column Grid 2 - Required Bar Size is smaller than the Preferred Bar Size. Maintaining the same cover will require slightly less reinforcement than
calculated.
RAPT 6.6.8.0 Project Name: J110 Page 2/19
Licensee: AECOM Singapore Pte Ltd 1/6/2022 7:36:24 PM License No.: 10479063400712WPN11
Frame Description: G/A.1/8/2, G/A.1/8/3, G/A.1/8/4
Project Name: J110 Beams
Frame Description: G/A.1/8/2, G/A.1/8/3, G/A.1/8/4 Beam Beam Beam Beam Effective
Designer: SLT Number Depth Width Width Flange
C:\Users\sujeevanleonard.tham\OneDrive - AECOM\Projects\J110\J110\OneDrive_2021-07-01\12. Southern at Width
Slab
Staircase\Design Files\Str\Beams\G,A.1,8,2.rpf mm mm mm mm
1 800 500 500 500
RAPT - Version: 6.6.8.0 2 800 500 500 500
Reinforced And Post-Tensioned Concrete Analysis & Design Package RC 800 500 500 500
Copyright(C) 1988 - 2021 PCDC Pty. Ltd. All Rights Reserved
Due to the different Concrete Strength types in the Design Standard and Materials in this run, the concrete strengths shown in the materials data have been
multiplied in the calculatiuons by 0.8 2. Extra Dead Load - Panel
Load Left End Left end of Load at Right Right end of Load at Description
Span reference load from left end End load from right
Span Span Slab Panel Panel column reference reference reference end
Length Depth Width Width column column column
Left Right # mm kN/m2 # mm kN/m2 A
mm mm mm mm 1 1 0 2.5 3 4200 2.5
LE 0
1 2400 200 400 400
2 1500 200 400 400 2. Extra Dead Load - Point
RC 4200 200 400 400 Load Reference Distance to Load Load Description
column Load from Length
reference
column
Columns # mm kN mm A
Column Column Support Transverse Transverse 1 3 2100 40 0
Grid Type Column prestress
Reference spacing (P/A)
A List mm MPa
1 1 Knife-Edge 400
2 2 Knife-Edge 400
3 3 Knife-Edge 400
RAPT 6.6.8.0 Project Name: J110 Page 3/19 RAPT 6.6.8.0 Project Name: J110 Page 4/19
Licensee: AECOM Singapore Pte Ltd 1/6/2022 7:36:28 PM License No.: 10479063400712WPN11 Licensee: AECOM Singapore Pte Ltd 1/6/2022 7:36:32 PM License No.: 10479063400712WPN11
Frame Description: G/A.1/8/2, G/A.1/8/3, G/A.1/8/4 Frame Description: G/A.1/8/2, G/A.1/8/3, G/A.1/8/4
3. Live Load - Line Load Combinations : Pre Existing
Load Left End Left end of Load Right Right end of Load Live Description Load Description 1. Self 2. Extra 3. Live
Reference load from at left End load from at right Load Combination Weight Dead Load Load
Column reference end reference reference end reduction A #.# #.# #.#
column column column 1 Pre Existing 1 0 0
# mm kN/m # mm kN/m #.# A
1 3 0 16.5 3 4200 16.5 1 LL=5.0KPA, 3.3M WIDTH
kN/m1 2 3 kN
20 80
3. Live Load - Point 15 1 60
Load Reference Distance to Load Load Live Description 10 40
column Load from Length Load 5 20
reference reduction 0 0
column 0 2400 3900mm
# mm kN mm #.# A 20 80
15 60
1 3 2100 65 0 1 L1
10 40
5 20
0 0
Load Combinations : Ultimate 1 2 3
Load Description 1. Self 2. Extra 3.
Combination Weight Dead Live Load Case 2 : 2. Extra Dead Load
Load Load
A #.# #.# #.#
1 Live Load 1.35 1.35 1.5 kN/m1 2 3 kN
20 80
2 Live Load 1 1 1.5
15 60
3 Dead Load 1.425 1.425 0 1
10 40
5 20
0 0
0 2400 3900mm
Load Combinations : Short Term Service 20 80
Load Description 1. Self 2. Extra 3. Live 15 60
Combination Weight Dead Load Load 10 40
A #.# #.# #.# 5 P1 20
1 Live Load 1 1 0.5 0 0
0 2400 3900mm
20 80
15 60
10 L1 40
Load Combinations : Permanent Service 5 20
Load Description 1. Self 2. Extra 3. Live 0 0
Combination Weight Dead Load Load 1 2 3
A #.# #.# #.#
1 Live Load 1 1 0.3
Load Case 3 : 3. Live Load
kN/m1 2 3 kN
Load Combinations : Deflection 20 1 80
Load Description 1. Self 2. Extra 3. Live 15 60
Combination Weight Dead Load Load 10 40
A #.# #.# #.# 5 20
1 Short Term - Deflection 1 1 0.5 0 0
0 2400 3900mm
2 Permanent - Deflection 1 1 0.3 20 80
3 Initial - Deflection 1 0 0 15 60
10 40
5 P1 20
0 0
Load Combinations : Transfer Prestress 0 2400 3900mm
20 L1 80
Load Description 1. Self 2. Extra 3. Live
15 60
Combination Weight Dead Load Load
10 40
A #.# #.# #.#
5 20
1 Transfer 1 0 0 0 0
1 2 3
RAPT 6.6.8.0 Project Name: J110 Page 5/19 RAPT 6.6.8.0 Project Name: J110 Page 6/19
Licensee: AECOM Singapore Pte Ltd 1/6/2022 7:36:35 PM License No.: 10479063400712WPN11 Licensee: AECOM Singapore Pte Ltd 1/6/2022 7:36:39 PM License No.: 10479063400712WPN11
Frame Description: G/A.1/8/2, G/A.1/8/3, G/A.1/8/4 Frame Description: G/A.1/8/2, G/A.1/8/3, G/A.1/8/4
Reinforcement
Reinforcement Reinforcement Preferred Number Maximum Ratio of Neutral Axis Depth for Ductility #.# 0.58
Use Type Bar Size of Legs Ductility Limit - Strain #.# 0
List List # Ductility Check at Left End Column Y/N Y
Flexural Bar H 500MPa Ductility Check at Right End Column Y/N Y
Flexural Mesh A 500MPa Minimum Reinforcement Strength Limit - #.## x M* #.# 0
Shear Option 1 H 500MPa 10 2 Flexural Critical Section - Consider Transverse Beams Y/N Y
Shear Option 2 H 500MPa 10 4 Flexural Critical Section - Distance from centre of Support #.# -1
Shear Option 3 H 500MPa 10 6 Beam Left Sideface Cover (Internal) mm 25
Punching Shear H 500MPa 10 2 Beam Right Sideface cover mm 40
Prestress Minimum Reinforcement Basis List Program Default
Shear Enhancement at Supports Y/N N
Reinforcement Ast Value in Shear Calculations List Calculated
Maximum Minimum Minimum Minimum Span Minimum Span Infill Stagger Limit Reinforcement Strain Y/N Y
Bar Bar Continuous Reinforcement Reinforcement Bars Bars Include Strain Hardening of Reinforcement Y/N N
Spacing Spacing Reinforcement into End into Internal Beam Shear Critical Section Location List Code Critical Section
Support Support
mm mm #.# #.# #.# Y/N Y/N
Support Reinforcement 300 60 0 N N
Maximum Service Stress Change - Prestressed Sections MPa 150
Span Reinforcement 300 60 0 0 N N
Maximum Service Stress Change - Reinforced Sections MPa 0
Relative Humidity % 50
Average Temperature C. 20
Design Zones Prestress Losses Calculations based on List Program Default
Layer Steel Left End Distance to Bar stagger Top Right End Distance to Bar stagger Top Cover Maximum Minimum Preferred Crack Width Calculations List Code default
Number type Reference left end of length at left Cover at Reference right end of length at right at Right Bar Size Bar Size bar size AS3600 Shrinkage and Temperature Reinforcement List Moderate
Column bar end left end Column bar end end Degree of Restraint in Primary Direction % 0
List # mm mm mm # mm mm mm List List List
Degree of Restraint in Secondary Direction % 0
1 Bar 1 0 0 40 4 0 0 40 40 20 32
Concrete Strength Gain Rate List N
Material Properties
Reinforcement Design Zones Concrete : Standard Concrete : Concrete Strength Basis - Cube
Description A C32/40MPa
1 2 3 Characteristic Compressive Strength MPa 40
mm
0 Mean Compressive Strength MPa 50
Lower Characteristic Tensile Strength MPa 2.12
-200 Upper Characteristic Tensile Strength MPa 3.93
Concrete Density kg/m3 2447
-400 Design Concrete Modulus MPa 31186.6
Mean Concrete Modulus MPa 33345.8
-600 Basic Shrinkage Strain mm/mm 0
Shrinkage Multiplier #.# 1
-800 Basic Creep Factor #.# 2.656
0 2400 3900mm Creep Multiplier #.# 1
Design Data Concrete Strain at Peak Stress #.# 0.002
Capacity Reduction factor (phi) for Flexure #.# 1 Squash Load Factor #.# 0.85
Capacity Reduction factor (phi) for Shear #.# 1 Concrete Strain Limit #.# 0.004
Capacity Reduction factor (phi) for Shear with transverse reinf #.# 1 Strength Gain Rate List Normal
Material Factor for Concrete in Flexure #.# 1.5 Maximum Aggregate Size mm 20
Material Factor for Concrete in Shear #.# 1.5
Material Factor for Reinforcement #.# 1.15
RAPT 6.6.8.0 Project Name: J110 Page 7/19 RAPT 6.6.8.0 Project Name: J110 Page 8/19
Licensee: AECOM Singapore Pte Ltd 1/6/2022 7:36:42 PM License No.: 10479063400712WPN11 Licensee: AECOM Singapore Pte Ltd 1/6/2022 7:36:46 PM License No.: 10479063400712WPN11
Frame Description: G/A.1/8/2, G/A.1/8/3, G/A.1/8/4 Frame Description: G/A.1/8/2, G/A.1/8/3, G/A.1/8/4
Reinforcement Bar Col No. 2 Self Extra Dead Live
Designation Type Yield Elastic Ductility Peak Peak Design Material Material Material Capacity Material Capacity Include as Description Weight Load Load
Stress Modulus Strain Stress Strain Factor Factor Reduction Factor Reduction Factor Flexural Moment Above kNm -0 -0 -0
Limit Flexure Shear - Flexure - Shear Reinforcement for Moment Below kNm -0 -0 -0
Shear Reaction kN -140.99 -142.73 -257.12
H Deformed 500 2.05e5 N 0.05 540 90 -1 -1 -1 -1 Y Elastic Rotation #.# 0 0 0
Elastic Axial Shortening mm 0 0 0
Nominal Bar Bar Area Bar Bar Stock Col No. 3 Self Extra Dead Live
Bar Size Diameter Inertia Weight Length Weight Load Load
A mm mm2 mm4 kg/m mm Moment Above kNm -0 -0 -0
10 10 78.5 491.07 0.62 12000 Moment Below kNm -0 -0 -0
13 13 132.7 1402.55 1.04 12000 Reaction kN 243.6 211.41 381.66
16 16 201.1 3218.29 1.58 12000 Elastic Rotation #.# 1.32e-4 1.16e-4 2.1e-4
20 20 314.2 7857.14 2.47 12000 Elastic Axial Shortening mm 0 0 0
22 22 380.1 11503.6 2.98 12000
25 25 490.9 19182.5 3.85 12000
32 32 804.2 51492.6 6.31 12000
40 40 1256.6 1.257e5 9.86 12000 Load Combinations
Column Actions
Col No. 1 Characteristic Characteristic Service Service Ultimate Ultimate Ultimate Ultimate
Elevation view Service Service (Reversal) Flexure Flexure Shear Shear
(Reversal) (Reversal) (Reversal)
1 2 3 Moment Above kNm 0 0 0 0 0 0 0 0
mm
0 Moment Below kNm 0 0 0 0 0 0 0 0
Reaction kN 64.57 64.57 51.6 51.6 91.06 91.06 38.48 91.2
-200 Elastic Rotation #.# 0 0 0 0 1.2e-4 1.2e-4 0 1.2e-4
Elastic Axial Shortening mm 0 0 0 0 0 0 0 0
-400
Col No. 2 Characteristic Characteristic Service Service Ultimate Ultimate Ultimate Ultimate
-600 Service Service (Reversal) Flexure Flexure Shear Shear
(Reversal) (Reversal) (Reversal)
-800 Moment Above kNm 0 0 0 0 0 0 0 0
0 2400 3900mm Moment Below kNm 0 0 0 0 0 0 0 0
Reaction kN -540.84 -540.84 -412.28 -412.28 -768.7 -768.7 -773.74 -276.08
Plan view Elastic Rotation #.# -1.58e-4 -1.58e-4 -1.23e-4 -1.23e-4 -2.25e-4 -2.25e-4 -2.24e-4 0
Elastic Axial Shortening mm 0 0 0 0 0 0 0 0
1 2 3
mm
-200 Col No. 3 Characteristic Characteristic Service Service Ultimate Ultimate Ultimate Ultimate
Service Service (Reversal) Flexure Flexure Shear Shear
-100 (Reversal) (Reversal) (Reversal)
Moment Above kNm 0 0 0 0 0 0 0 0
0 Moment Below kNm 0 0 0 0 0 0 0 0
Reaction kN 836.67 836.67 645.84 645.84 1186.76 1186.76 456.16 1187.65
100 Elastic Rotation #.# 4.58e-4 4.58e-4 3.53e-4 3.53e-4 6.5e-4 6.5e-4 2.48e-4 6.49e-4
Elastic Axial Shortening mm 0 0 0 0 0 0 0 0
200
0 2400 3900mm
Warnings
Ultimate Design
Input
No errors or warnings were found. Flexure
1 2 3
Output kNm
Warning:Incremental Deflection span/deflection ratio in at least one span is less than defined limit. -1000 -928 -928
Warning:Total deflection in at least one span is greater than defined limit.
-800
Warning:SPAN Reinforcing Bar spacing There have been problems in determining a bar size to satisfy the design spacing requirements. See Detailed
Reinforcement Design Comments. -600
-400
-200
9.03
0 170 170 -143
200 97.1
Bending Moments
Load Cases 0 2400 3900mm
Column Actions
Moment Moment 1 Moment 2
Col No. 1 Self Extra Dead Live
Weight Load Load
Moment Above kNm -0 -0 -0
Moment Below kNm -0 -0 -0
Reaction kN 24.35 14.27 25.95
Elastic Rotation #.# 0 0 0
Elastic Axial Shortening mm 0 0 0
RAPT 6.6.8.0 Project Name: J110 Page 9/19 RAPT 6.6.8.0 Project Name: J110 Page 10/19
Licensee: AECOM Singapore Pte Ltd 1/6/2022 7:36:50 PM License No.: 10479063400712WPN11 Licensee: AECOM Singapore Pte Ltd 1/6/2022 7:36:54 PM License No.: 10479063400712WPN11
Frame Description: G/A.1/8/2, G/A.1/8/3, G/A.1/8/4 Frame Description: G/A.1/8/2, G/A.1/8/3, G/A.1/8/4
1 2 3 1 2 3
kN
kNm
600 408 -1000
400
80.2 -800
200 61
-600
0
-200 -400
-400 -200
-600 0
-800 200
-730-734
0 2400 3900mm 0 2400 3900mm
Shear 1 2 3
0.254
0.254
0.3
1 2 3
0.25
kNm
-1000 -928 -928 0.2
0.15
-800
0.1
-600 0.05
-400 0
-200 -0.05
9.03
0.058
0 171 170 -144 -0.1
200 0 2400 3900mm
96.3
0 2400 3900mm Neutral Axis Depth Initial Final
Moment Moment 1 Moment 2
Service
Maximum Moment Condition
1 2 3
kN
600 1 2 3
408 MPa MPa
400 -12 -1.76 -9.33 -9.33 -240
200 80.5 63.3 -8 -160
0 -4 -80
-200
0 0
-400
4 80
-600
8 160
-800 -732-735 12 240
0 2400 3900mm 16 1.94 9.35 9.35 320
0 2400 3900mm
Shear Shear 1 Shear 2
Gross Stress Top Gross Stress Bottom Cracked Compression Reinforcement Tension
Flexural Design Reversal Moment Condition
Ultimate
1 2 3
1 2 3 MPa MPa
mm2 -12 -1.2 -6.56 -6.56 -240
36000 0 3220
-8 -160
3000
-4 -80
2400
1800 0 0
1200 4 80
600 8 160
0 12 240
-600 16 1.31 6.58 6.58 320
-1200 557 557 0 0 2400 3900mm
0 2400 3900mm
Gross Stress Top Gross Stress Bottom Cracked Compression Reinforcement Tension
Reinforcement Top Total Bottom Total Top Ultimate Bottom Ultimate Min Top Min Bot
RAPT 6.6.8.0 Project Name: J110 Page 11/19 RAPT 6.6.8.0 Project Name: J110 Page 12/19
Licensee: AECOM Singapore Pte Ltd 1/6/2022 7:36:58 PM License No.: 10479063400712WPN11 Licensee: AECOM Singapore Pte Ltd 1/6/2022 7:37:01 PM License No.: 10479063400712WPN11
Frame Description: G/A.1/8/2, G/A.1/8/3, G/A.1/8/4 Frame Description: G/A.1/8/2, G/A.1/8/3, G/A.1/8/4
Permanent Shear Design
Maximum Moment Condition Beam
Span 1
MPa1 2 3 MPa Locat V* Mv* Pv Mdec d Ast bv phi Vuc phi Vut phi Vu Phi Vumax phi VuMin phi Vus Theta Asv/s
-12 -1.54 -8.22 -8.23 -240
-9 -180
-6 -120 mm kN kNm kN kNm mm mm2 mm kN kN kN kN kN kN #.# mm2/mm
-3 -60 100 89.48 9.03 0 0 744 556.93 400 0 0 0 1494.76 0 0 0
0 0 640 80.5 54.5 0 0 744 556.93 400 110.25 99999 110.25 1494.76 263.52 0 21.8 0.36
3 60
826 77.44 68.8 0 0 744 556.93 400 110.25 99999 110.25 1494.76 263.52 0 21.8 0.36
6 120
1012 74.47 82.94 0 0 744 556.93 400 110.25 99999 110.25 1494.76 263.52 0 21.8 0.36
9 180
1200 71.73 96.28 0 0 744 556.93 400 110.25 99999 110.25 1494.76 263.52 0 21.8 0.36
12 240
1.69 8.24 8.24 1388 68.78 109.12 0 0 744 556.93 400 110.25 99999 110.25 1494.76 263.52 0 21.8 0.36
15 300
0 2400 3900mm 1574 65.96 121.38 0 0 744 556.93 400 110.25 99999 110.25 1494.76 263.52 0 21.8 0.36
1760 63.32 133.41 0 0 744 556.93 400 110.25 99999 110.25 1494.76 263.52 0 21.8 0.36
Gross Stress Top Gross Stress Bottom Cracked Compression Reinforcement Tension
2399 54.15 170.69 0 0 744 556.93 400 0 0 0 1494.76 0 0 0
Reversal Moment Condition
Spacing of Sets Minimum Legs Shear Comments
2 legs 4 legs 6 legs Min legs
MPa1 2 3 MPa
H10 H10 H10 H10
-12 -240
-1.2 -6.56 -6.56 mm mm mm mm # A
-9 -180
-6 -120
-3 -60 433.7 558 558 433.7 2 Minimum Steel
0 0 433.7 558 558 433.7 2 Minimum Steel
3 60 433.7 558 558 433.7 2 Minimum Steel
6 120 433.7 558 558 433.7 2 Minimum Steel
9 180 433.7 558 558 433.7 2 Minimum Steel
12 240 433.7 558 558 433.7 2 Minimum Steel
1.32 6.58 6.58
15 300 433.7 558 558 433.7 2 Minimum Steel
0 2400 3900mm
Gross Stress Top Gross Stress Bottom Cracked Compression Reinforcement Tension
280 558 558 280 2 Even Spans Loaded Odd Spans Loaded All Spans Loaded
285 558 558 285 2
290.3 558 558 290.3 2 Incremental
295.8 558 558 295.8 2
310.7 558 558 310.7 2 mm1 2 3
327.3 558 558 327.3 2 0
-0.272 0.528
433.7 558 558 433.7 2 Minimum Steel
433.7 558 558 433.7 2 Minimum Steel -20
433.7 558 558 433.7 2 Minimum Steel -23.5
433.7 558 558 433.7 2 Minimum Steel -40
433.7 558 558 433.7 2 Minimum Steel
433.7 558 558 433.7 2 Minimum Steel -60
433.7 558 558 433.7 2 Minimum Steel
8820 2843 179
0 2400 3900mm
-60
mm1 2 3 Span 3
0 Design Comments:-
-0.041 0.065 -3.26 - Incremental Span/Deflection ratio less than user defined limit = 179
-20 - Total Deflection greater than user defined limit = -26.6mm
-40
Even Spans Loaded
-60
-40
-60
mm1 2 3 mm1 2 3
0 0
-0.07 0.181 -0.097 0.324
-8.47
-20 -20 -14.5
-40 -40
-60 -60
All Spans Loaded Odd Spans Loaded Even Spans Loaded All Spans Loaded Even Spans Loaded Odd Spans Loaded
Incremental Incremental
mm1 2 3 mm1 2 3
0 0
-0.244 0.385 -0.272 0.528
-20 -20
-17.5
-23.5
-40 -40
-60 -60
All Spans Loaded Odd Spans Loaded Even Spans Loaded All Spans Loaded Even Spans Loaded Odd Spans Loaded
mm1 2 3 mm1 2 3
0 0
-0.284 0.444 -0.311 0.587
-20 -20
-20.5
-26.5
-40 -40
-60 -60
All Spans Loaded Odd Spans Loaded Even Spans Loaded All Spans Loaded Even Spans Loaded Odd Spans Loaded
Span 3 Span 3
Design Comments:- Design Comments:-
- Incremental Span/Deflection ratio less than user defined limit = 240 - Incremental Span/Deflection ratio less than user defined limit = 179
- Total Deflection greater than user defined limit = -26.5mm
Max Max Section Max Max Section Max Max Section Max Max Section
Locat Size Space Area Depth Width Rebar Reqd Size Space Area Depth Width Rebar Reqd Locat Size Space Area Depth Width Rebar Reqd Size Space Area Depth Width Rebar Reqd
mm mm mm mm2 mm mm A mm mm mm2 mm mm A mm mm mm mm2 mm mm A mm mm mm2 mm mm A
1200 0 0 0 56 400 No Steel Added 32 300 556.93 744 500 2 H20 @ 295 1181 16 204.5 3210.93 56 400 4 H32 @ 94.3 0 0 0 744 500 No Steel Added
1388 0 0 0 56 400 No Steel Added 32 300 556.93 744 500 2 H20 @ 295 1234 16 205.4 3210.93 56 400 4 H32 @ 94.3 0 0 0 744 500 No Steel Added
1574 0 0 0 56 400 No Steel Added 25 288 556.93 744 500 2 H20 @ 295 1287 16 206.2 3210.93 56 400 4 H32 @ 94.3 0 0 0 744 500 No Steel Added
1760 0 0 0 56 400 No Steel Added 25 268.9 556.93 744 500 2 H20 @ 295 1340 16 207 3210.93 56 400 4 H32 @ 94.3 0 0 0 744 500 No Steel Added
1800 0 0 0 56 400 No Steel Added 25 264.9 556.93 744 500 2 H20 @ 295 1393 16 207.7 3210.93 56 400 4 H32 @ 94.3 0 0 0 744 500 No Steel Added
1889 0 0 0 56 400 No Steel Added 25 256.1 556.93 744 500 2 H20 @ 295 1446 16 208.4 3210.93 56 400 4 H32 @ 94.3 0 0 0 744 500 No Steel Added
1974 0 0 0 56 400 No Steel Added 16 248.2 556.93 744 500 2 H20 @ 295 1499 16 209.3 3218.99 56 400 5 H32 @ 70.8 0 0 0 744 500 No Steel Added
2059 0 0 0 56 400 No Steel Added 16 240.5 556.93 744 500 2 H20 @ 295 Shear Reinforcement
2144 0 0 0 56 400 No Steel Added 16 233 556.93 744 500 2 H20 @ 295 Spacing of Sets
2229 0 0 0 56 400 No Steel Added 16 225.5 556.93 744 500 2 H20 @ 295 2 legs 4 legs 6 legs Min legs Minimum Shear
2314 0 0 0 56 400 No Steel Added 16 218.3 556.93 744 500 2 H20 @ 295 Area H10 H10 H10 H10 Legs Comments
2399 0 0 0 56 400 No Steel Added 16 211.3 556.93 744 500 2 H20 @ 295 mm2/mm mm mm mm mm # A
Shear Reinforcement
Spacing of Sets
2 legs 4 legs 6 legs Min legs Minimum Shear
Area H10 H10 H10 H10 Legs Comments
mm2/mm mm mm mm mm # A
Design Comments:-
- SPAN Reinforcing Bar spacing - Span 2 - Smallest preferred reinforcement size requires bar spacing larger than maximum. It will be necessary to use
smaller bars than the preferred minimum size or a larger area of reinforcement than is required by design.
- - Span 2 - Required Bar Size is smaller than the Preferred Bar Size. Maintaining the same cover will require slightly less reinforcement than calculated.
- Span - 2 - Reinforcement added at right support contraflexure point for Offset of Bending Moment Diagram for Shear - 2085.52mm2
- Span - 2 - Reinforcement added at right span contraflexure point for Offset of Bending Moment Diagram for Shear - 537.3mm2
Design Comments:-
- SPAN Reinforcing Bar spacing - Span 1 - Smallest preferred reinforcement size requires bar spacing larger than maximum. It will be necessary to use Span 3
smaller bars than the preferred minimum size or a larger area of reinforcement than is required by design. Top Reinforcement Bottom Reinforcement
- - Span 1 - Required Bar Size is smaller than the Preferred Bar Size. Maintaining the same cover will require slightly less reinforcement than calculated.
- Span - 1 - Reinforcement added at left span contraflexure point for Offset of Bending Moment Diagram for Shear - 262.17mm2 Max Max Section Max Max Section
Locat Size Space Area Depth Width Rebar Reqd Size Space Area Depth Width Rebar Reqd
Span 2 mm mm mm mm2 mm mm A mm mm mm2 mm mm A
Top Reinforcement Bottom Reinforcement 1 16 209.3 3220.17 56 400 5 H32 @ 70.8 0 0 0 744 500 No Steel Added
150 16 207.9 3212.11 56 400 4 H32 @ 94.3 0 0 0 744 500 No Steel Added
Max Max Section Max Max Section 313 16 207.4 3212.11 56 400 4 H32 @ 94.3 0 0 0 744 500 No Steel Added
Locat Size Space Area Depth Width Rebar Reqd Size Space Area Depth Width Rebar Reqd 476 16 205.1 3212.11 56 400 4 H32 @ 94.3 0 0 0 744 500 No Steel Added
mm mm mm mm2 mm mm A mm mm mm2 mm mm A 640 16 203.7 3212.11 56 400 4 H32 @ 94.3 0 0 0 744 500 No Steel Added
1 0 0 0 56 400 No Steel Added 16 212.5 556.93 744 500 2 H20 @ 295 776 16 202.6 3143.61 56 400 4 H32 @ 94.3 0 0 0 744 500 No Steel Added
54 0 0 0 56 400 No Steel Added 25 278.1 556.93 744 500 2 H20 @ 295 912 16 202.6 2932.36 56 400 4 H32 @ 94.3 0 0 0 744 500 No Steel Added
107 0 0 0 56 400 No Steel Added 32 300 556.93 744 500 2 H20 @ 295 1050 16 202.2 2723.05 56 400 4 H32 @ 94.3 0 0 0 744 500 No Steel Added
160 0 0 0 56 400 No Steel Added 32 300 556.93 744 500 2 H20 @ 295 1400 12 199.5 2220.19 56 400 3 H32 @ 141.5 0 0 0 744 500 No Steel Added
213 0 0 0 56 400 No Steel Added 32 300 556.93 744 500 2 H20 @ 295 1750 16 202 1752.77 56 400 3 H32 @ 141.5 0 0 0 744 500 No Steel Added
266 32 300 2159.67 56 400 3 H32 @ 141.5 0 0 0 744 500 No Steel Added 2100 25 288.4 689.64 56 400 1 H32 @ 999 0 0 0 744 500 No Steel Added
319 32 300 2282.88 56 400 3 H32 @ 141.5 0 0 0 744 500 No Steel Added 2450 32 300 523.47 56 400 1 H32 @ 999 0 0 0 744 500 No Steel Added
375 32 300 2413.42 56 400 4 H32 @ 94.3 0 0 0 744 500 No Steel Added 2800 32 300 511.5 56 400 1 H32 @ 999 0 0 0 744 500 No Steel Added
507 16 200.5 2723.36 56 400 4 H32 @ 94.3 0 0 0 744 500 No Steel Added 3150 32 300 511.5 56 400 1 H32 @ 999 0 0 0 744 500 No Steel Added
640 12 199.3 3045.18 56 400 4 H32 @ 94.3 0 0 0 744 500 No Steel Added 3468 32 300 511.5 56 400 1 H32 @ 999 0 0 0 744 500 No Steel Added
750 12 198.7 3210.93 56 400 4 H32 @ 94.3 0 0 0 744 500 No Steel Added 3784 32 300 511.5 56 400 1 H32 @ 999 0 0 0 744 500 No Steel Added
860 16 201.6 3210.93 56 400 4 H32 @ 94.3 0 0 0 744 500 No Steel Added 4100 32 300 511.5 56 400 1 H32 @ 999 0 0 0 744 500 No Steel Added
993 16 202.6 3210.93 56 400 4 H32 @ 94.3 0 0 0 744 500 No Steel Added
1125 16 203.7 3210.93 56 400 4 H32 @ 94.3 0 0 0 744 500 No Steel Added
RAPT 6.6.8.0 Project Name: J110 Page 19/19
Licensee: AECOM Singapore Pte Ltd 1/6/2022 7:37:28 PM License No.: 10479063400712WPN11
Frame Description: G/A.1/8/2, G/A.1/8/3, G/A.1/8/4
Shear Reinforcement
Spacing of Sets
2 legs 4 legs 6 legs Min legs Minimum Shear
Area H10 H10 H10 H10 Legs Comments
mm2/mm mm mm mm mm # A
Reinforcement Layout
1 2 3
5-H32
mm
0
-200
-400
-600
2-H20
2-H20
-800
0 2400 3900mm
- SPAN Reinforcing Bar spacing - Span 1 - Smallest preferred reinforcement size requires bar spacing larger than maximum. It will be necessary to use
smaller bars than the preferred minimum size or a larger area of reinforcement than is required by design.
- - Span 1 - Required Bar Size is smaller than the Preferred Bar Size. Maintaining the same cover will require slightly less reinforcement than calculated.
Design Comments:-
- Span - 1 - Reinforcement added at left span contraflexure point for Offset of Bending Moment Diagram for Shear - 262.17mm2
- SPAN Reinforcing Bar spacing - Span 2 - Smallest preferred reinforcement size requires bar spacing larger than maximum. It will be necessary to use
smaller bars than the preferred minimum size or a larger area of reinforcement than is required by design.
- - Span 2 - Required Bar Size is smaller than the Preferred Bar Size. Maintaining the same cover will require slightly less reinforcement than calculated.
- Span - 2 - Reinforcement added at right span contraflexure point for Offset of Bending Moment Diagram for Shear - 537.3mm2
RAPT 6.6.8.0 Project Name: J110 Page 2/18
Licensee: AECOM Singapore Pte Ltd 1/6/2022 7:32:03 PM License No.: 10479063400712WPN11
Frame Description: G/A.2/8/2, GA.2/8/1
Project Name: J110 Beams
Frame Description: G/A.2/8/2, GA.2/8/1 Beam Beam Beam Beam Effective
Designer: SLT Number Depth Width Width Flange
C:\Users\sujeevanleonard.tham\OneDrive - AECOM\Projects\J110\J110\OneDrive_2021-07-01\12. Southern at Width
Slab
Staircase\Design Files\Str\Beams\G,A.2,8,2, G, A.2,8,1.rpf mm mm mm mm
1 900 750 750 2110
RAPT - Version: 6.6.8.0 RC 900 750 750 750
Reinforced And Post-Tensioned Concrete Analysis & Design Package
Copyright(C) 1988 - 2021 PCDC Pty. Ltd. All Rights Reserved
Load Cases
Licensee Load Load Type Load Definition Live Load Description
AECOM Singapore Pte Ltd Case Deflection Case
300 Beach Road
#03-00 The Concourse List List Y/N A
Singapore 199555 1 Self Weight Applied Loads
10479063400712WPN11 2 Initial Dead Load Applied Loads
3 Extra Dead Load Applied Loads
4 Live Load Applied Loads Y
kN/m1 2
120
Load Combinations : Transfer Prestress 90
Load Description 1. Self 2. Initial 3. Extra 4. Live 60
Combination Weight Dead Load Dead Load Load 30 P1
A #.# #.# #.# #.# 0
0 8000mm
1 Transfer 1 0 0 0 120
90 L1
60
30 L2
Load Combinations : Pre Existing 0
Load Description 1. Self 2. Initial 3. Extra 4. Live 1 2
Combination Weight Dead Load Dead Load Load
A #.# #.# #.# #.# Reinforcement
1 Pre Existing 1 0 0 0 Reinforcement Reinforcement Preferred Number
Use Type Bar Size of Legs
List List #
Load Combinations : Construction Flexural Bar H 500MPa
Load Description 1. Self 2. Initial 3. Extra 4. Live Flexural Mesh A 500MPa
Combination Weight Dead Load Dead Load Load Shear Option 1 H 500MPa 10 2
A #.# #.# #.# #.# Shear Option 2 H 500MPa 10 4
1 Construction 1 0 0 0 Shear Option 3 H 500MPa 10 6
Punching Shear H 500MPa 10 2
RAPT 6.6.8.0 Project Name: J110 Page 5/18 RAPT 6.6.8.0 Project Name: J110 Page 6/18
Licensee: AECOM Singapore Pte Ltd 1/6/2022 7:32:13 PM License No.: 10479063400712WPN11 Licensee: AECOM Singapore Pte Ltd 1/6/2022 7:32:17 PM License No.: 10479063400712WPN11
Frame Description: G/A.2/8/2, GA.2/8/1 Frame Description: G/A.2/8/2, GA.2/8/1
Reinforcement
Maximum Minimum Minimum Minimum Span Minimum Span Infill Stagger Limit Reinforcement Strain Y/N Y
Bar Bar Continuous Reinforcement Reinforcement Bars Bars Include Strain Hardening of Reinforcement Y/N N
Spacing Spacing Reinforcement into End into Internal Beam Shear Critical Section Location List Code Critical Section
Support Support
mm mm #.# #.# #.# Y/N Y/N
Support Reinforcement 300 60 0 N N
Span Reinforcement 300 60 0 0 N N Maximum Service Stress Change - Prestressed Sections MPa 150
Maximum Service Stress Change - Reinforced Sections MPa 0
Relative Humidity % 50
Average Temperature C. 20
Design Zones Prestress Losses Calculations based on List Program Default
Layer Steel Left End Distance to Bar stagger Top Right End Distance to Bar stagger Top Cover Maximum Minimum Preferred Crack Width Calculations List Code default
Number type Reference left end of length at left Cover at Reference right end of length at right at Right Bar Size Bar Size bar size
AS3600 Shrinkage and Temperature Reinforcement List Moderate
Column bar end left end Column bar end end
List # mm mm mm # mm mm mm List List List Degree of Restraint in Primary Direction % 0
1 Bar 1 0 0 60 2 4000 0 60 40 20 32 Degree of Restraint in Secondary Direction % 0
Concrete Strength Gain Rate List N
Layer Minimum Maximum Minimum % in
Number Number of Spacing of Steel area as Flange Concrete Tensile Strength for Deflection Calculations- #.## x (Fc)n #.# -1
Bars Bars % Maximum Value of Ieff/Igross for Deflection Calculations #.# 0.6
# mm % % Total Deflection Warning Limit - Maximum Span/Deflection #.# 250
1 0 0 0 0 Total Deflection Warning Limit - Maximum Deflection mm 25
Incremental Deflection Warning Limit - Maximum Span/Deflection #.# 500
Incremental Deflection Warning Limit - Maximum Deflection mm 25
Design Zones Initial Time for Shrinkage List Full Shrinkage
Layer Steel Left End Distance to Bar stagger Bottom Right End Distance to Bar stagger Bottom Maximum Minimum Preferred Time of Loading in days #.# 10
Number type Reference left end of length at left Cover at left Reference right end of length at right Cover at Bar Size Bar Size bar size Age Adjustment Factor #.# 0.76
Column bar end end Column bar end Right End Concrete Strength at Time of Loading MPa 27.04
List # mm mm mm # mm mm mm List List List Loaded Period in years #.# 30
1 Bar 1 0 0 60 2 4000 0 60 40 20 32 Tension stiffening Approach List Modified Concrete Tensile Modulus Method
Material Properties
Reinforcement Design Zones Concrete : Standard Concrete : Concrete Strength Basis - Cube
Description A C32/40MPa
1 2
mm Characteristic Compressive Strength MPa 40
0 Mean Compressive Strength MPa 50
Lower Characteristic Tensile Strength MPa 2.12
-200 Upper Characteristic Tensile Strength MPa 3.93
Concrete Density kg/m3 2447
-400
Design Concrete Modulus MPa 31186.6
-600 Mean Concrete Modulus MPa 33345.8
Basic Shrinkage Strain mm/mm 0
-800 Shrinkage Multiplier #.# 1
Basic Creep Factor #.# 2.656
0 8000mm #.#
Creep Multiplier 1
Design Data Concrete Strain at Peak Stress #.# 0.002
Capacity Reduction factor (phi) for Flexure #.# 1 Squash Load Factor #.# 0.85
Capacity Reduction factor (phi) for Shear #.# 1 Concrete Strain Limit #.# 0.004
Capacity Reduction factor (phi) for Shear with transverse reinf #.# 1 Strength Gain Rate List Normal
Material Factor for Concrete in Flexure #.# 1.5 Maximum Aggregate Size mm 20
Material Factor for Concrete in Shear #.# 1.5
Material Factor for Reinforcement #.# 1.15
Maximum Ratio of Neutral Axis Depth for Ductility #.# 0.58
Ductility Limit - Strain #.# 0
Reinforcement Bar
Designation Type Yield Elastic Ductility Peak Peak Design Material Material Material Capacity Material Capacity Include as Description
Ductility Check at Left End Column Y/N Y
Stress Modulus Strain Stress Strain Factor Factor Reduction Factor Reduction Factor Flexural
Ductility Check at Right End Column Y/N Y Limit Flexure Shear - Flexure - Shear Reinforcement for
Minimum Reinforcement Strength Limit - #.## x M* #.# 0 Shear
Flexural Critical Section - Consider Transverse Beams Y/N Y H Deformed 500 2.05e5 N 0.05 540 90 -1 -1 -1 -1 Y
Flexural Critical Section - Distance from centre of Support #.# -1
Beam Left Sideface Cover (Internal) mm 25
Beam Right Sideface cover mm 40 Nominal Bar Bar Area Bar Bar Stock
Prestress Minimum Reinforcement Basis List Program Default Bar Size Diameter Inertia Weight Length
Shear Enhancement at Supports Y/N N A mm mm2 mm4 kg/m mm
Ast Value in Shear Calculations List Calculated 10 10 78.5 491.07 0.62 12000
RAPT 6.6.8.0 Project Name: J110 Page 7/18 RAPT 6.6.8.0 Project Name: J110 Page 8/18
Licensee: AECOM Singapore Pte Ltd 1/6/2022 7:32:24 PM License No.: 10479063400712WPN11 Licensee: AECOM Singapore Pte Ltd 1/6/2022 7:32:27 PM License No.: 10479063400712WPN11
Frame Description: G/A.2/8/2, GA.2/8/1 Frame Description: G/A.2/8/2, GA.2/8/1
Load Combinations
Nominal Bar Bar Area Bar Bar Stock Column Actions
Bar Size Diameter Inertia Weight Length Col No. 1 Characteristic Characteristic Service Service Ultimate Ultimate Ultimate Ultimate
A mm mm2 mm4 kg/m mm Service Service (Reversal) Flexure Flexure Shear Shear
13 13 132.7 1402.55 1.04 12000 (Reversal) (Reversal) (Reversal)
16 16 201.1 3218.29 1.58 12000 Moment Above kNm 0 0 0 0 0 0 0 0
20 20 314.2 7857.14 2.47 12000 Moment Below kNm 0 0 0 0 0 0 0 0
22 22 380.1 11503.6 2.98 12000 Reaction kN 730.78 730.78 641.35 641.35 1013.39 1013.39 530.92 1034.39
25 25 490.9 19182.5 3.85 12000 Elastic Rotation #.# 2.04e-3 2.04e-3 1.79e-3 1.79e-3 2.82e-3 2.82e-3 1.44e-3 2.92e-3
32 32 804.2 51492.6 6.31 12000 Elastic Axial Shortening mm 0 0 0 0 0 0 0 0
40 40 1256.6 1.257e5 9.86 12000
Col No. 2 Characteristic Characteristic Service Service Ultimate Ultimate Ultimate Ultimate
Elevation view Service Service (Reversal) Flexure Flexure Shear Shear
(Reversal) (Reversal) (Reversal)
1 2 Moment Above kNm 0 0 0 0 0 0 0 0
mm Moment Below kNm 0 0 0 0 0 0 0 0
0 Reaction kN 1072.81 1072.81 939.65 939.65 1488.25 1488.25 911.48 1488.25
Elastic Rotation #.# -1.8e-3 -1.8e-3 -1.58e-3 -1.58e-3 -2.5e-3 -2.5e-3 -1.17e-3 -2.5e-3
-200
Elastic Axial Shortening mm 0 0 0 0 0 0 0 0
-400
-600
Ultimate Design
-800
Flexure
0 8000mm
kNm1 2
Plan view -1200 -607 -607
-600
103
mm1 2 0
-1400 600
1200
-700 1800
2400
0 3000
2884
0 8000mm
700
Moment Moment 1 Moment 2
1400
0 8000mm
Warnings 1 2
kN
Input 1200 976
No errors or warnings were found.
800
400 252
Output
0
Warning:Incremental Deflection span/deflection ratio in at least one span is less than defined limit.
Warning:Total deflection in at least one span is greater than defined limit. -400
-800
-1200
-1100
-1600
0 8000mm
Bending Moments
Shear Shear 1 Shear 2
Load Cases
Column Actions
Col No. 1 Self Initial Dead Extra Dead Live Shear
Weight Load Load Load
Moment Above kNm -0 -0 -0 -0 kNm1 2
Moment Below kNm -0 -0 -0 -0 -1200 -607 -607
Reaction kN 280.93 157.08 113.9 178.87 -600
Elastic Rotation #.# 7.37e-4 4.83e-4 3.15e-4 4.99e-4 103
0
Elastic Axial Shortening mm 0 0 0 0 600
1200
Col No. 2 Self Initial Extra Live 1800
Weight Dead Dead Load
2400
Load Load 2379
Moment Above kNm -0 -0 -0 -0 3000
Moment Below kNm -0 -0 -0 -0 0 8000mm
Reaction kN 394.67 245.42 166.4 266.33
Elastic Rotation #.# -6.56e-4 -4.25e-4 -2.8e-4 -4.4e-4 Moment Moment 1 Moment 2
Elastic Axial Shortening mm 0 0 0 0
RAPT 6.6.8.0 Project Name: J110 Page 9/18 RAPT 6.6.8.0 Project Name: J110 Page 10/18
Licensee: AECOM Singapore Pte Ltd 1/6/2022 7:32:31 PM License No.: 10479063400712WPN11 Licensee: AECOM Singapore Pte Ltd 1/6/2022 7:32:35 PM License No.: 10479063400712WPN11
Frame Description: G/A.2/8/2, GA.2/8/1 Frame Description: G/A.2/8/2, GA.2/8/1
Service
1 2
kN
Maximum Moment Condition
1200 976
800 MPa1 2 MPa
252 -16 -11.88 -3.62 -280
400
-12 -210
0
-8 -140
-400
-4 -70
-800
0 0
-1200 4 70
-1121
-1600 8 140
0 8000mm
12 210
7.76 3.7
Shear Shear 1 Shear 2 0 8000mm
Flexural Design Gross Stress Top Gross Stress Bottom Cracked Compression Reinforcement Tension
Ultimate Reversal Moment Condition
mm21 2
MPa1 2 MPa
40000 2163 -16 -280
-9.87 -3.09
2000 -12 -210
0 -8 -140
-2000 -4 -70
-4000 0 0
-6000 4 70
-8000 8 140
-10000 8576 0 12 210
6.45 3.16
0 8000mm
0 8000mm
Reinforcement Top Total Bottom Total Top Ultimate Bottom Ultimate Min Top Min Bot Gross Stress Top Gross Stress Bottom Cracked Compression Reinforcement Tension
1 2
kNm Permanent
-1200 Maximum Moment Condition
-600
0 1 2
600 MPa -11.15 -3.4 MPa
1200 -12 -240
1800 -8 -160
2400 -4 -80
3000 0 0
3600
0 8000mm 4 80
8 160
Capacity Minimum Ultimate Design Initial Final 12 240
7.29 3.49
0 8000mm
1 2
0.103
0.083
Gross Stress Top Gross Stress Bottom Cracked Compression Reinforcement Tension
0.12
0.08 Reversal Moment Condition
0.04
0 1 2
-0.04 MPa -9.94 -3.09 MPa
-0.08 -12 -240
-0.12 -8 -160
-0.16 -4 -80
0.145
0 8000mm 0 0
4 80
Neutral Axis Depth Initial Final 8 160
Span 1 12 6.5 3.16 240
Design Comments:- 0 8000mm
- As there is no area of steel in the tension zone (any prestressing tendons are in the compression zone) we are now adding an area of steel, equivalent to
that required for minimum reinforcement, to the design tension layer. This is then assumed to be the initial design reinforcement setup. More reinforcement will Gross Stress Top Gross Stress Bottom Cracked Compression Reinforcement Tension
be added as required to achieve the applied moments. Ast added = 1889.91mm2 @ 7280mm
RAPT 6.6.8.0 Project Name: J110 Page 11/18 RAPT 6.6.8.0 Project Name: J110 Page 12/18
Licensee: AECOM Singapore Pte Ltd 1/6/2022 7:32:38 PM License No.: 10479063400712WPN11 Licensee: AECOM Singapore Pte Ltd 1/6/2022 7:32:42 PM License No.: 10479063400712WPN11
Frame Description: G/A.2/8/2, GA.2/8/1 Frame Description: G/A.2/8/2, GA.2/8/1
Characteristic Service
Maximum Moment Condition Spacing of Sets Minimum Legs Shear Comments
2 legs 4 legs 6 legs Min legs
1 2 H10 H10 H10 H10
MPa MPa mm mm mm mm # A
-16 -13.7 -4.15 -320 144.3 288.6 432.9 216.4 3
-12 -240 149.8 299.6 449.5 224.7 3
-8 -160 221 442 600 331.5 3
-4 -80 231.3 462.6 600 346.9 3 Minimum Steel
0 0
231.3 462.6 600 346.9 3 Minimum Steel
4 80
231.3 462.6 600 346.9 3 Minimum Steel
8 160
12 240 224.5 449 600 336.8 3
16 8.95 4.25 320 132.4 264.7 397.1 198.5 3
0 8000mm 126.9 253.7 380.6 190.3 3
123.8 247.7 371.5 185.8 3
Gross Stress Top Gross Stress Bottom Cracked Compression Reinforcement Tension 121.2 242.4 363.7 181.8 3
118.3 236.6 354.8 177.4 3
Reversal Moment Condition 115.5 230.9 346.4 173.2 3
112.9 225.9 338.8 169.4 3
1 2
MPa MPa
-16 -9.68 -3.09 -320
-12 -240
-8 -160 Span 2
-4 -80 Locat V* Mv* Pv Mdec d Ast bv phi Vuc phi Vut phi Vu Phi Vumax phi VuMin phi Vus Theta Asv/s
0 0
4 80
8 160 mm kN kNm kN kNm mm mm2 mm kN kN kN kN kN kN #.# mm2/mm
12 240 1 308.97 -607.41 0 0 824 1758.03 750 0 0 0 3104.04 0 0 0
16 6.33 3.16 320 720 251.86 -405.8 0 0 824 1163.84 750 223.14 99999 223.14 3104.04 547.23 251.86 21.8 0.68
0 8000mm
860 240.74 -371.31 0 0 824 1062.84 750 223.14 99999 223.14 3104.04 547.23 240.74 21.8 0.68
Gross Stress Top Gross Stress Bottom Cracked Compression Reinforcement Tension 1000 229.62 -338.39 0 0 824 1006.7 750 223.14 99999 223.14 3104.04 547.23 229.62 21.8 0.68
1200 213.74 -294.05 0 0 824 1006.7 750 223.14 99999 223.14 3104.04 547.23 0 21.8 0.68
1466 192.61 -240.01 0 0 824 1006.7 750 223.14 99999 223.14 3104.04 547.23 0 21.8 0.68
Shear Design 1732 171.49 -191.58 0 0 824 1006.7 750 223.14 99999 223.14 3104.04 547.23 0 21.8 0.68
Beam 2000 150.2 -148.47 0 0 824 1006.7 750 223.14 99999 223.14 3104.04 547.23 0 21.8 0.68
Span 1 2201 134.24 -119.89 0 0 824 1006.7 750 223.14 99999 223.14 3104.04 547.23 0 21.8 0.68
Locat V* Mv* Pv Mdec d Ast bv phi Vuc phi Vut phi Vu Phi Vumax phi VuMin phi Vus Theta Asv/s 2401 118.36 -94.63 0 0 824 1006.7 750 223.14 99999 223.14 3104.04 547.23 0 21.8 0.68
2701 96.15 -62.45 0 0 824 1006.7 750 223.14 99999 223.14 3104.04 547.23 0 21.8 0.68
3000 74.02 -37.01 0 0 824 1006.7 750 223.14 99999 223.14 3104.04 547.23 0 21.8 0.68
mm kN kNm kN kNm mm mm2 mm kN kN kN kN kN kN #.# mm2/mm 3300 51.81 -18.14 0 0 824 1006.7 750 223.14 99999 223.14 3104.04 547.23 0 21.8 0.68
100 1026.27 103.03 0 0 824 1248.78 750 0 0 0 3104.04 0 0 0 3600 29.61 -5.92 0 0 824 1006.7 750 223.14 99999 223.14 3104.04 547.23 0 21.8 0.68
720 975.91 723.71 0 0 824 2058.33 750 243.61 99999 243.61 3104.04 547.23 975.91 21.8 1.21 3900 7.4 -0.37 0 0 824 1006.7 750 223.14 99999 223.14 3104.04 547.23 0 21.8 0.68
1040 951.23 1022.7 0 0 824 2952.75 750 274.74 99999 274.74 3104.04 547.23 951.23 21.8 1.18
1360 925.23 1322.94 0 0 824 3834.07 750 299.74 99999 299.74 3104.04 547.23 925.23 21.8 1.15 Spacing of Sets Minimum Legs Shear Comments
1680 899.24 1614.85 0 0 824 4696.14 750 320.7 99999 320.7 3104.04 547.23 899.24 21.8 1.12 2 legs 4 legs 6 legs Min legs
2000 877.19 1874.83 0 0 824 5553.46 750 339.14 99999 339.14 3104.04 547.23 877.19 21.8 1.09 H10 H10 H10 H10
2399 844.78 2218.36 0 0 824 6599.23 750 359.21 99999 359.21 3104.04 547.23 844.78 21.8 1.05 mm mm mm mm # A
2932 572.67 2428.12 0 0 824 7749.36 750 378.97 99999 378.97 3104.04 547.23 572.67 21.8 0.71
3465 288.01 2659.82 0 0 824 8398.75 750 389.28 99999 389.28 3104.04 547.23 0 21.8 0.68 231.3 462.6 600 346.9 3 Minimum Steel
4000 -171.42 2378.73 0 0 824 8575.67 750 391.99 99999 391.99 3104.04 547.23 0 21.8 0.68 231.3 462.6 600 346.9 3 Minimum Steel
4050 -191.71 2369.65 0 0 824 8566.18 750 391.85 99999 391.85 3104.04 547.23 0 21.8 0.68 231.3 462.6 600 346.9 3 Minimum Steel
4826 -563.74 2358.92 0 0 824 7879.38 750 381.08 99999 381.08 3104.04 547.23 563.74 21.8 0.7 231.3 462.6 600 346.9 3 Minimum Steel
5601 -956.27 1956.4 0 0 824 6155.1 750 350.97 99999 350.97 3104.04 547.23 956.27 21.8 1.19 231.3 462.6 600 346.9 3 Minimum Steel
5701 -997.71 1858.68 0 0 824 5864.15 750 345.35 99999 345.35 3104.04 547.23 997.71 21.8 1.24 231.3 462.6 600 346.9 3 Minimum Steel
6000 -1022 1556.73 0 0 824 4961.7 750 326.63 99999 326.63 3104.04 547.23 1022 21.8 1.27 231.3 462.6 600 346.9 3 Minimum Steel
6320 -1044.06 1250.42 0 0 824 4011.1 750 304.28 99999 304.28 3104.04 547.23 1044.06 21.8 1.3 231.3 462.6 600 346.9 3 Minimum Steel
6640 -1070.05 912.16 0 0 824 3036.01 750 277.3 99999 277.3 3104.04 547.23 1070.05 21.8 1.33 231.3 462.6 600 346.9 3 Minimum Steel
6960 -1096.04 565.59 0 0 824 2050.2 750 243.29 99999 243.29 3104.04 547.23 1096.04 21.8 1.36 231.3 462.6 600 346.9 3 Minimum Steel
7280 -1120.72 220.25 0 0 824 1248.78 750 223.14 99999 223.14 3104.04 547.23 1120.72 21.8 1.39 231.3 462.6 600 346.9 3 Minimum Steel
7999 -1179.12 -606.54 0 0 824 2163.47 750 0 0 0 3104.04 0 0 0 231.3 462.6 600 346.9 3 Minimum Steel
231.3 462.6 600 346.9 3 Minimum Steel
Spacing of Sets Minimum Legs Shear Comments 231.3 462.6 600 346.9 3 Minimum Steel
2 legs 4 legs 6 legs Min legs
H10 H10 H10 H10
mm mm mm mm # A
0
-21.8
-30
Deflections -60 367 161
All Spans Loaded 0 8000mm
Transfer
Even Spans Loaded Odd Spans Loaded All Spans Loaded
1 2
mm Even Spans Loaded
60 Transfer
30
5.58 1 2
-4.41
0 mm
60
-30
30
-60 1816 716 5.58
-4.41
0 8000mm 0
Even Spans Loaded Odd Spans Loaded All Spans Loaded -30
Even Spans Loaded Odd Spans Loaded All Spans Loaded -30
0 -19 0
-22.2
-30 -30
All Spans Loaded Odd Spans Loaded Even Spans Loaded All Spans Loaded Even Spans Loaded Odd Spans Loaded
Span 2
Odd Spans Loaded Design Comments:-
Transfer - Incremental Span/Deflection ratio less than user defined limit = 246
- Total Deflection greater than user defined limit = 27.3mm
1 2
mm
60
Detailed Reinforcement
30 Span 1
5.58
-4.41 Top Reinforcement Bottom Reinforcement
0
Reinforcement Layout
Design Comments:- 1 2
5-H25
- - Column Grid 2 - Required Bar Size is smaller than the Preferred Bar Size. Maintaining the same cover will require slightly less reinforcement than mm
calculated. 0
- - Span 1 - Required Bar Size is greater than the Preferred Bar Size. Maintaining the same cover will require slightly more reinforcement than calculated.
RAPT has increased the required reinforcement by the ratio of the effective depths for the 2 bar sizes in the reinforcement layout. -200
- Span - 1 - Reinforcement added at right support contraflexure point for Offset of Bending Moment Diagram for Shear - 1770.38mm2
- Span - 1 - Reinforcement added at left span contraflexure point for Offset of Bending Moment Diagram for Shear - 2973.85mm2 -400
- Span - 1 - Reinforcement added at right span contraflexure point for Offset of Bending Moment Diagram for Shear - 2619.64mm2
-600
Span 2 -800
7-H40
Top Reinforcement Bottom Reinforcement
0 8000mm
Max Max Section Max Max Section
Locat Size Space Area Depth Width Rebar Reqd Size Space Area Depth Width Rebar Reqd
mm mm mm mm2 mm mm A mm mm mm2 mm mm A - - Column Grid 2 - Required Bar Size is smaller than the Preferred Bar Size. Maintaining the same cover will require slightly less reinforcement than
calculated.
1 12 151.5 1758.03 76 750 4 H25 @ 213.3 0 0 0 824 750 No Steel Added
- - Span 1 - Required Bar Size is greater than the Preferred Bar Size. Maintaining the same cover will require slightly more reinforcement than calculated.
144 12 152.7 1757.28 76 750 4 H25 @ 213.3 0 0 0 824 750 No Steel Added RAPT has increased the required reinforcement by the ratio of the effective depths for the 2 bar sizes in the reinforcement layout.
287 12 153.2 1757.28 76 750 4 H25 @ 213.3 0 0 0 824 750 No Steel Added Design Comments:-
430 12 152.8 1757.28 76 750 4 H25 @ 213.3 0 0 0 824 750 No Steel Added - Span - 1 - Reinforcement added at left span contraflexure point for Offset of Bending Moment Diagram for Shear - 2973.85mm2
573 12 153 1757.28 76 750 4 H25 @ 213.3 0 0 0 824 750 No Steel Added - Span - 1 - Reinforcement added at right span contraflexure point for Offset of Bending Moment Diagram for Shear - 2619.64mm2
720 12 154.1 1757.28 76 750 4 H25 @ 213.3 0 0 0 824 750 No Steel Added
860 12 151.6 1751.82 76 750 4 H25 @ 213.3 0 0 0 824 750 No Steel Added - - Column Grid 2 - Required Bar Size is smaller than the Preferred Bar Size. Maintaining the same cover will require slightly less reinforcement than
1000 12 165.2 1624.9 76 750 4 H25 @ 213.3 0 0 0 824 750 No Steel Added calculated.
1200 16 209.3 1452.83 76 750 3 H25 @ 320 0 0 0 824 750 No Steel Added
1466 25 263.3 1238.02 76 750 3 H25 @ 320 0 0 0 824 750 No Steel Added
1732 32 300 1039.22 76 750 3 H25 @ 320 0 0 0 824 750 No Steel Added
2000 32 300 1006.7 76 750 3 H25 @ 320 0 0 0 824 750 No Steel Added
2201 32 300 1006.7 76 750 3 H25 @ 320 0 0 0 824 750 No Steel Added
2401 32 300 1006.7 76 750 3 H25 @ 320 0 0 0 824 750 No Steel Added
2701 32 300 1006.7 76 750 3 H25 @ 320 0 0 0 824 750 No Steel Added
3000 32 300 1006.7 76 750 3 H25 @ 320 0 0 0 824 750 No Steel Added
3300 32 300 1006.7 76 750 3 H25 @ 320 0 0 0 824 750 No Steel Added
3600 32 300 1006.7 76 750 3 H25 @ 320 0 0 0 824 750 No Steel Added
3900 32 300 1006.7 76 750 3 H25 @ 320 0 0 0 824 750 No Steel Added
Shear Reinforcement
Spacing of Sets
2 legs 4 legs 6 legs Min legs Minimum Shear
Area H10 H10 H10 H10 Legs Comments
mm2/mm mm mm mm mm # A
Due to the different Concrete Strength types in the Design Standard and Materials in this run, the concrete strengths shown in the materials data have been Load Combinations : Ultimate
multiplied in the calculatiuons by 0.8 Load Description 1. Self 2. Extra 3.
Combination Weight Dead Live
Span Load Load
A #.# #.# #.#
Span Span Slab Panel Panel
Length Depth Width Width 1 Live Load 1.35 1.35 1.5
Left Right 2 Live Load 1 1 1.5
mm mm mm mm 3 Dead Load 1.425 1.425 0
LE 0
1 3200 200 3000 3000
RC 3000 200 3000 3000 Load Combinations : Short Term Service
Load Description 1. Self 2. Extra 3. Live
Combination Weight Dead Load Load
Columns A #.# #.# #.#
Column Column Support Transverse Transverse 1 Live Load 1 1 0.5
Grid Type Column prestress
Reference spacing (P/A)
A List mm MPa
Load Combinations : Permanent Service
1 1 Knife-Edge 3000
Load Description 1. Self 2. Extra 3. Live
2 2 Knife-Edge 3000 Combination Weight Dead Load Load
A #.# #.# #.#
1 Live Load 1 1 0.3
RAPT 6.6.8.0 Project Name: J110 Page 3/16 RAPT 6.6.8.0 Project Name: J110 Page 4/16
Licensee: AECOM Singapore Pte Ltd 1/6/2022 7:28:54 PM License No.: 10479063400712WPN11 Licensee: AECOM Singapore Pte Ltd 1/6/2022 7:28:59 PM License No.: 10479063400712WPN11
Frame Description: G/B.1/8/4, G/B.1/8/5 Frame Description: G/B.1/8/4, G/B.1/8/5
Load Combinations : Deflection Reinforcement
Load Description 1. Self 2. Extra 3. Live Maximum Minimum Minimum Minimum Span Minimum Span Infill Stagger
Combination Weight Dead Load Load Bar Bar Continuous Reinforcement Reinforcement Bars Bars
A #.# #.# #.# Spacing Spacing Reinforcement into End into Internal
1 Short Term - Deflection 1 1 0.5 Support Support
2 Permanent - Deflection 1 1 0.3 mm mm #.# #.# #.# Y/N Y/N
3 Initial - Deflection 1 0 0 Support Reinforcement 300 60 0 N N
Span Reinforcement 300 60 0 0 N N
Limit Reinforcement Strain Y/N Y Nominal Bar Bar Area Bar Bar Stock
Include Strain Hardening of Reinforcement Y/N N Bar Size Diameter Inertia Weight Length
Beam Shear Critical Section Location List Code Critical Section A mm mm2 mm4 kg/m mm
13 13 132.7 1402.55 1.04 12000
16 16 201.1 3218.29 1.58 12000
20 20 314.2 7857.14 2.47 12000
Maximum Service Stress Change - Prestressed Sections MPa 200
22 22 380.1 11503.6 2.98 12000
Maximum Service Stress Change - Reinforced Sections MPa 200
25 25 490.9 19182.5 3.85 12000
Relative Humidity % 50
32 32 804.2 51492.6 6.31 12000
Average Temperature C. 20
40 40 1256.6 1.257e5 9.86 12000
Prestress Losses Calculations based on List Program Default
Crack Width Calculations List .20 mm
AS3600 Shrinkage and Temperature Reinforcement List Moderate Elevation view
Degree of Restraint in Primary Direction % 0
Degree of Restraint in Secondary Direction % 0 1 2
mm
Concrete Strength Gain Rate List N 0
Concrete Tensile Strength for Deflection Calculations- #.## x (Fc)n #.# -1 -200
Maximum Value of Ieff/Igross for Deflection Calculations #.# 0.6
Total Deflection Warning Limit - Maximum Span/Deflection #.# 250 -400
Total Deflection Warning Limit - Maximum Deflection mm 40
Incremental Deflection Warning Limit - Maximum Span/Deflection #.# 360 -600
Incremental Deflection Warning Limit - Maximum Deflection mm 25
Initial Time for Shrinkage List Full Shrinkage
0 3200mm
Time of Loading in days #.# 10
Age Adjustment Factor #.# 0.76
Plan view
Concrete Strength at Time of Loading MPa 27.04
Loaded Period in years #.# 30
Tension stiffening Approach List Modified Concrete Tensile Modulus Method mm1 2
-1400
0.151
0.151
-240 0.18
0 3200mm 0.15
0.12
Shear Shear 1 Shear 2 0.09
0.06
Shear 0.03
0
-0.03
1 2
kNm -0.06
0.052
-300 -268 -268 -0.09
0 3200mm
-250
-200 Neutral Axis Depth Initial Final
-150
-100 Span 1
-50 Design Comments:-
4.02 - As there is no area of steel in the tension zone (any prestressing tendons are in the compression zone) we are now adding an area of steel, equivalent to
0
11.7 that required for minimum reinforcement, to the design tension layer. This is then assumed to be the initial design reinforcement setup. More reinforcement will
50
be added as required to achieve the applied moments. Ast added = 371.35mm2 @ 800mm
0 3200mm
Gross Stress Top Gross Stress Bottom Cracked Compression Reinforcement Tension Limits
MPa1 2 MPa
-6 -4.09 -4.09 -210
-4 -140 Shear Design
-2 -70 Beam
0 0 Span 1
2 70 Locat V* Mv* Pv Mdec d Ast bv phi Vuc phi Vut phi Vu Phi Vumax phi VuMin phi Vus Theta Asv/s
4 140
6 210
mm kN kNm kN kNm mm mm2 mm kN kN kN kN kN kN #.# mm2/mm
8 280
4.27 4.27 100 37.23 4.02 0 0 644 415.51 400 0 0 0 1293.85 0 0 0
0 3200mm 560 -45.8 -18.03 0 0 644 415.51 400 99.11 99999 99.11 1293.85 228.1 0 21.8 0.36
680 -50.26 -23.79 0 0 644 415.51 400 99.11 99999 99.11 1293.85 228.1 0 21.8 0.36
Gross Stress Top Gross Stress Bottom Cracked Compression Reinforcement Tension Limits
800 -56.4 -26.04 0 0 644 415.51 400 99.11 99999 99.11 1293.85 228.1 0 21.8 0.36
1066 -66.27 -42.35 0 0 644 415.51 400 99.11 99999 99.11 1293.85 228.1 0 21.8 0.36
1332 -78.96 -56.04 0 0 644 415.51 400 99.11 99999 99.11 1293.85 228.1 0 21.8 0.36
1600 -92.85 -72.24 0 0 644 415.51 400 99.11 99999 99.11 1293.85 228.1 0 21.8 0.36
1868 -104.89 -91.91 0 0 644 473.98 400 99.11 99999 99.11 1293.85 228.1 104.89 21.8 0.36
2134 -117.94 -115.91 0 0 644 604.17 400 99.11 99999 99.11 1293.85 228.1 117.94 21.8 0.36
2400 -133.8 -149.39 0 0 644 760.64 400 101.77 99999 101.77 1293.85 228.1 133.8 21.8 0.36
2520 -139.27 -161.63 0 0 644 834.98 400 104.98 99999 104.98 1293.85 228.1 139.27 21.8 0.36
2640 -146.42 -178.77 0 0 644 912.98 400 108.16 99999 108.16 1293.85 228.1 146.42 21.8 0.36
3199 -179.19 -268.13 0 0 644 1326.17 400 0 0 0 1293.85 0 0 0
RAPT 6.6.8.0 Project Name: J110 Page 11/16 RAPT 6.6.8.0 Project Name: J110 Page 12/16
Licensee: AECOM Singapore Pte Ltd 1/6/2022 7:29:25 PM License No.: 10479063400712WPN11 Licensee: AECOM Singapore Pte Ltd 1/6/2022 7:29:29 PM License No.: 10479063400712WPN11
Frame Description: G/B.1/8/4, G/B.1/8/5 Frame Description: G/B.1/8/4, G/B.1/8/5
Spacing of Sets Minimum Legs Shear Comments Deflections
2 legs 4 legs 6 legs Min legs All Spans Loaded
H10 H10 H10 H10
mm mm mm mm # A Transfer
1 2
433.7 483 483 433.7 2 Minimum Steel mm
433.7 483 483 433.7 2 Minimum Steel 0
433.7 483 483 433.7 2 Minimum Steel 0.152
-2.05
433.7 483 483 433.7 2 Minimum Steel -10
433.7 483 483 433.7 2 Minimum Steel
433.7 483 483 433.7 2 Minimum Steel -20
433.7 483 483 433.7 2 Minimum Steel
433.7 483 483 433.7 2 Minimum Steel -30
433.7 483 483 433.7 2 Minimum Steel
-40 21110 1467
433.7 483 483 433.7 2 Minimum Steel
0 3200mm
433.7 483 483 433.7 2 Minimum Steel
Short Term
1 2
mm
Span 2
0
Locat V* Mv* Pv Mdec d Ast bv phi Vuc phi Vut phi Vu Phi Vumax phi VuMin phi Vus Theta Asv/s 0.374
-10 -5.69
mm kN kNm kN kNm mm mm2 mm kN kN kN kN kN kN #.# mm2/mm
-20
1 178.82 -268.13 0 0 644 1326.07 400 0 0 0 1293.85 0 0 0
560 145.49 -177.49 0 0 644 866.61 400 106.29 99999 106.29 1293.85 228.1 145.49 21.8 0.36
-30
750 134.16 -150.93 0 0 644 734.06 400 100.57 99999 100.57 1293.85 228.1 134.16 21.8 0.36
1000 119.25 -119.25 0 0 644 574.37 400 99.11 99999 99.11 1293.85 228.1 119.25 21.8 0.36 8552 528
-40
1250 104.34 -91.3 0 0 644 440.3 400 99.11 99999 99.11 1293.85 228.1 104.34 21.8 0.36 0 3200mm
1500 89.44 -67.08 0 0 644 415.51 400 99.11 99999 99.11 1293.85 228.1 0 21.8 0.36
1750 74.53 -46.58 0 0 644 415.51 400 99.11 99999 99.11 1293.85 228.1 0 21.8 0.36 Even Spans Loaded Odd Spans Loaded All Spans Loaded
2000 59.63 -29.81 0 0 644 415.51 400 99.11 99999 99.11 1293.85 228.1 0 21.8 0.36
2250 44.72 -16.77 0 0 644 415.51 400 99.11 99999 99.11 1293.85 228.1 0 21.8 0.36 Incremental
2468 31.72 -8.44 0 0 644 415.51 400 99.11 99999 99.11 1293.85 228.1 0 21.8 0.36
1 2
2684 18.84 -2.98 0 0 644 415.51 400 99.11 99999 99.11 1293.85 228.1 0 21.8 0.36 mm
2900 5.96 -0.3 0 0 644 415.51 400 99.11 99999 99.11 1293.85 228.1 0 21.8 0.36 0
0.851
Spacing of Sets Minimum Legs Shear Comments -10
2 legs 4 legs 6 legs Min legs -11.4
H10 H10 H10 H10 -20
mm mm mm mm # A
-30
433.7 483 483 433.7 2 Minimum Steel
433.7 483 483 433.7 2 Minimum Steel -40 3761 263
433.7 483 483 433.7 2 Minimum Steel 0 3200mm
433.7 483 483 433.7 2 Minimum Steel Even Spans Loaded Odd Spans Loaded All Spans Loaded
433.7 483 483 433.7 2 Minimum Steel
433.7 483 483 433.7 2 Minimum Steel Total Long Term
433.7 483 483 433.7 2 Minimum Steel
433.7 483 483 433.7 2 Minimum Steel 1 2
433.7 483 483 433.7 2 Minimum Steel mm
433.7 483 483 433.7 2 Minimum Steel 0
0.994
433.7 483 483 433.7 2 Minimum Steel
-10
-13.3
-20
Punching -30
Column Head Critical Section 3218 225
-40
Column Bh a at u d fcv P/A Asw/s min V* Mv* V*eff VRd1 VRd2 Asv result 0 3200mm
No.
A #.# mm mm mm mm MPa MPa mm2/mm kN kNm kN kN kN mm2 A Even Spans Loaded Odd Spans Loaded All Spans Loaded
1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Check Not Carried Out!
2 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Check Not Carried Out!
RAPT 6.6.8.0 Project Name: J110 Page 13/16 RAPT 6.6.8.0 Project Name: J110 Page 14/16
Licensee: AECOM Singapore Pte Ltd 1/6/2022 7:29:32 PM License No.: 10479063400712WPN11 Licensee: AECOM Singapore Pte Ltd 1/6/2022 7:29:35 PM License No.: 10479063400712WPN11
Frame Description: G/B.1/8/4, G/B.1/8/5 Frame Description: G/B.1/8/4, G/B.1/8/5
Even Spans Loaded Odd Spans Loaded
Transfer Transfer
1 2 1 2
mm mm
0 0
0.152 0.152
-2.05 -2.05
-10 -10
-20 -20
-30 -30
1 2 1 2
mm mm
0 0
0.44 0.182
-3.24
-10 -5.98 -10
-20 -20
-30 -30
All Spans Loaded Odd Spans Loaded Even Spans Loaded All Spans Loaded Even Spans Loaded Odd Spans Loaded
Incremental Incremental
1 2 1 2
mm mm
0 0
0.916 0.658
-10 -10
-8.98
-11.7
-20 -20
-30 -30
All Spans Loaded Odd Spans Loaded Even Spans Loaded All Spans Loaded Even Spans Loaded Odd Spans Loaded
1 2 1 2
mm mm
0 0
1.06 0.802
-10 -10
-10.9
-13.6
-20 -20
-30 -30
All Spans Loaded Odd Spans Loaded Even Spans Loaded All Spans Loaded Even Spans Loaded Odd Spans Loaded
Detailed Reinforcement
Span 1
Top Reinforcement Bottom Reinforcement
Max Max Section Max Max Section Max Max Section Max Max Section
Locat Size Space Area Depth Width Rebar Reqd Size Space Area Depth Width Rebar Reqd Locat Size Space Area Depth Width Rebar Reqd Size Space Area Depth Width Rebar Reqd
mm mm mm mm2 mm mm A mm mm mm2 mm mm A mm mm mm mm2 mm mm A mm mm mm2 mm mm A
215 25 300 415.28 56 400 2 H20 @ 295 25 300 415.51 644 400 2 H22 @ 293 560 16 151.3 1022.76 56 400 3 H25 @ 145 0 0 0 644 400 No Steel Added
330 25 300 415.28 56 400 2 H20 @ 295 25 300 415.51 644 400 2 H22 @ 293 750 16 151.6 944.44 56 400 2 H25 @ 290 0 0 0 644 400 No Steel Added
445 25 300 415.51 56 400 2 H20 @ 295 25 300 415.28 644 400 2 H22 @ 293 1000 16 150.8 780.89 56 400 2 H25 @ 290 0 0 0 644 400 No Steel Added
560 25 300 415.51 56 400 2 H20 @ 295 25 300 415.28 644 400 2 H22 @ 293 1250 16 152.7 633.34 56 400 2 H25 @ 290 0 0 0 644 400 No Steel Added
680 25 300 415.51 56 400 2 H20 @ 295 25 300 415.28 644 400 2 H22 @ 293 1500 25 207.8 501.78 56 400 2 H25 @ 290 0 0 0 644 400 No Steel Added
800 25 300 415.51 56 400 2 H20 @ 295 25 300 415.28 644 400 2 H22 @ 293 1750 25 300 415.51 56 400 1 H25 @ 999 0 0 0 644 400 No Steel Added
1066 25 300 415.51 56 400 2 H20 @ 295 0 0 415.28 644 400 2 H22 @ 293 2000 25 300 415.51 56 400 1 H25 @ 999 0 0 0 644 400 No Steel Added
1332 25 300 465.9 56 400 2 H20 @ 295 0 0 415.28 644 400 2 H22 @ 293 2250 25 300 415.51 56 400 1 H25 @ 999 0 0 0 644 400 No Steel Added
1600 16 187.2 582.92 56 400 2 H25 @ 290 0 0 415.28 644 400 2 H22 @ 293 2468 25 300 415.51 56 400 1 H25 @ 999 0 0 0 644 400 No Steel Added
1868 16 152.1 705.4 56 400 2 H25 @ 290 0 0 0 644 400 No Steel Added 2684 25 300 415.51 56 400 1 H25 @ 999 0 0 0 644 400 No Steel Added
2134 16 150.1 841.92 56 400 2 H25 @ 290 0 0 0 644 400 No Steel Added 2900 25 300 415.51 56 400 1 H25 @ 999 0 0 0 644 400 No Steel Added
2400 16 151.5 998.51 56 400 3 H25 @ 145 0 0 0 644 400 No Steel Added Shear Reinforcement
2520 16 151.4 1022.9 56 400 3 H25 @ 145 0 0 0 644 400 No Steel Added Spacing of Sets
2640 16 151.3 1022.9 56 400 3 H25 @ 145 0 0 0 644 400 No Steel Added 2 legs 4 legs 6 legs Min legs Minimum Shear
2755 16 151.2 1022.9 56 400 3 H25 @ 145 0 0 0 644 400 No Steel Added Area H10 H10 H10 H10 Legs Comments
2870 16 151.1 1073 56 400 3 H25 @ 145 0 0 0 644 400 No Steel Added mm2/mm mm mm mm mm # A
2985 16 151 1158.21 56 400 3 H25 @ 145 0 0 0 644 400 No Steel Added
3100 16 150.9 1246.92 56 400 3 H25 @ 145 0 0 0 644 400 No Steel Added
3199 16 150.9 1326.17 56 400 3 H25 @ 145 0 0 0 644 400 No Steel Added
Shear Reinforcement
Spacing of Sets
2 legs 4 legs 6 legs Min legs Minimum Shear 0.36 433.7 483 483 433.7 2 Minimum Steel
Area H10 H10 H10 H10 Legs Comments 0.36 433.7 483 483 433.7 2 Minimum Steel
mm2/mm mm mm mm mm # A 0.36 433.7 483 483 433.7 2 Minimum Steel
0.36 433.7 483 483 433.7 2 Minimum Steel
0.36 433.7 483 483 433.7 2 Minimum Steel
0.36 433.7 483 483 433.7 2 Minimum Steel
0.36 433.7 483 483 433.7 2 Minimum Steel
0.36 433.7 483 483 433.7 2 Minimum Steel 0.36 433.7 483 483 433.7 2 Minimum Steel
0.36 433.7 483 483 433.7 2 Minimum Steel 0.36 433.7 483 483 433.7 2 Minimum Steel
0.36 433.7 483 483 433.7 2 Minimum Steel 0.36 433.7 483 483 433.7 2 Minimum Steel
0.36 433.7 483 483 433.7 2 Minimum Steel 0.36 433.7 483 483 433.7 2 Minimum Steel
0.36 433.7 483 483 433.7 2 Minimum Steel
0.36 433.7 483 483 433.7 2 Minimum Steel Design Comments:-
0.36 433.7 483 483 433.7 2 Minimum Steel - - Column Grid 2 - Required Bar Size is smaller than the Preferred Bar Size. Maintaining the same cover will require slightly less reinforcement than
0.36 433.7 483 483 433.7 2 Minimum Steel calculated.
0.36 433.7 483 483 433.7 2 Minimum Steel
0.36 433.7 483 483 433.7 2 Minimum Steel
0.36 433.7 483 483 433.7 2 Minimum Steel
Reinforcement Layout
1 2
2-H20
3-H25
mm
0
-200
Design Comments:-
- SUPPORT Reinforcing Bar Spacing - Column Grid 1 - Smallest preferred reinforcement size requires bar spacing larger than maximum. It will be -400
necessary to use smaller bars than the preferred minimum size or a larger area of reinforcement than is required by design.
- - Column Grid 1 - Required Bar Size is smaller than the Preferred Bar Size. Maintaining the same cover will require slightly less reinforcement than
calculated. -600
2-H22
- - Column Grid 2 - Required Bar Size is smaller than the Preferred Bar Size. Maintaining the same cover will require slightly less reinforcement than
calculated. 0 3200mm
- - Span 1 - Required Bar Size is smaller than the Preferred Bar Size. Maintaining the same cover will require slightly less reinforcement than calculated.
- Span - 1 - Reinforcement added at left span contraflexure point for Offset of Bending Moment Diagram for Shear - 62.23mm2
- Span - 1 - Reinforcement added at right span contraflexure point for Offset of Bending Moment Diagram for Shear - 62.23mm2 - SUPPORT Reinforcing Bar Spacing - Column Grid 1 - Smallest preferred reinforcement size requires bar spacing larger than maximum. It will be
necessary to use smaller bars than the preferred minimum size or a larger area of reinforcement than is required by design.
- - Column Grid 1 - Required Bar Size is smaller than the Preferred Bar Size. Maintaining the same cover will require slightly less reinforcement than
Span 2 calculated.
Top Reinforcement Bottom Reinforcement - - Column Grid 2 - Required Bar Size is smaller than the Preferred Bar Size. Maintaining the same cover will require slightly less reinforcement than
calculated.
Max Max Section Max Max Section - - Span 1 - Required Bar Size is smaller than the Preferred Bar Size. Maintaining the same cover will require slightly less reinforcement than calculated.
Locat Size Space Area Depth Width Rebar Reqd Size Space Area Depth Width Rebar Reqd Design Comments:-
mm mm mm mm2 mm mm A mm mm mm2 mm mm A - Span - 1 - Reinforcement added at left span contraflexure point for Offset of Bending Moment Diagram for Shear - 62.23mm2
1 16 150.9 1326.07 56 400 3 H25 @ 145 0 0 0 644 400 No Steel Added - Span - 1 - Reinforcement added at right span contraflexure point for Offset of Bending Moment Diagram for Shear - 62.23mm2
112 16 150.9 1226.43 56 400 3 H25 @ 145 0 0 0 644 400 No Steel Added
223 16 151 1131.03 56 400 3 H25 @ 145 0 0 0 644 400 No Steel Added - - Column Grid 2 - Required Bar Size is smaller than the Preferred Bar Size. Maintaining the same cover will require slightly less reinforcement than
334 16 151.1 1039.76 56 400 3 H25 @ 145 0 0 0 644 400 No Steel Added calculated.
445 16 151.2 1022.76 56 400 3 H25 @ 145 0 0 0 644 400 No Steel Added
RAPT 6.6.8.0 Project Name: J110 Page 2/18
Licensee: AECOM Singapore Pte Ltd 1/6/2022 7:26:45 PM License No.: 10479063400712WPN11
Frame Description: G/C/8,G/C/8-1
Project Name: J110 Column Transverse
Frame Description: G/C/8,G/C/8-1 prestress
(P/A)
Designer: SLT MPa
C:\Users\sujeevanleonard.tham\OneDrive - AECOM\Projects\J110\J110\OneDrive_2021-07-01\12. Southern 1 0
Staircase\Design Files\Str\Beams\G,C,8, G,C,8-1.rpf 2 0
Load Cases
Load Load Type Load Definition Live Load Description
Case Deflection Case
Span
Span Span Slab Panel Panel External External Edge 2. Extra Dead Load - Panel
Length Depth Width Width Edge Distance Load Left End Left end of Load at Right Right end of Load at Description
Left Right Distance Left Right reference load from left end End load from right
mm mm mm mm mm mm column reference reference reference end
LE 0 column column column
1 6100 350 1500 1500 0 0 # mm kN/m2 # mm kN/m2 A
RC 1200 350 1500 1500 0 0 1 1 0 2.5 2 1200 2.5 SDL
kN/m1 2 kN
32 120
Load Combinations : Deflection 24 90
Load Description 1. Self 2. Extra 3. Live 16 2 3 60
8 1 430
Combination Weight Dead Load Load
A #.# #.# #.# 0 0
0 6100mm
1 Short Term - Deflection 1 1 0.5 32 120
2 Permanent - Deflection 1 1 0.3 24 90
3 Initial - Deflection 1 0 0 16 60
P1 P1
8 30
0 0
1 2
Load Combinations : Transfer Prestress
Load Description 1. Self 2. Extra 3. Live Reinforcement
Combination Weight Dead Load Load Reinforcement Reinforcement Preferred Number
A #.# #.# #.# Use Type Bar Size of Legs
1 Transfer 1 0 0 List List #
Flexural Bar H 500MPa
Flexural Mesh A 500MPa
Load Combinations : Pre Existing Shear Option 1 H 500MPa 10 2
Load Description 1. Self 2. Extra 3. Live Shear Option 2 H 500MPa 10 4
Combination Weight Dead Load Load Shear Option 3 H 500MPa 10 6
A #.# #.# #.# Punching Shear H 500MPa 10 2
1 Pre Existing 1 0 0
RAPT 6.6.8.0 Project Name: J110 Page 5/18 RAPT 6.6.8.0 Project Name: J110 Page 6/18
Licensee: AECOM Singapore Pte Ltd 1/6/2022 7:26:55 PM License No.: 10479063400712WPN11 Licensee: AECOM Singapore Pte Ltd 1/6/2022 7:26:59 PM License No.: 10479063400712WPN11
Frame Description: G/C/8,G/C/8-1 Frame Description: G/C/8,G/C/8-1
Reinforcement
Maximum Minimum Minimum Minimum Span Minimum Span Infill Stagger Limit Reinforcement Strain Y/N Y
Bar Bar Continuous Reinforcement Reinforcement Bars Bars Include Strain Hardening of Reinforcement Y/N N
Spacing Spacing Reinforcement into End into Internal Beam Shear Critical Section Location List Code Critical Section
Support Support
mm mm #.# #.# #.# Y/N Y/N
Support Reinforcement 300 60 0 N N
Span Reinforcement 300 60 0 0 N N Maximum Service Stress Change - Prestressed Sections MPa 200
Maximum Service Stress Change - Reinforced Sections MPa 200
Relative Humidity % 50
Average Temperature C. 20
Design Zones Prestress Losses Calculations based on List Program Default
Layer Steel Left End Distance to Bar stagger Top Right End Distance to Bar stagger Top Cover Maximum Minimum Preferred Crack Width Calculations List .20 mm
Number type Reference left end of length at left Cover at Reference right end of length at right at Right Bar Size Bar Size bar size
AS3600 Shrinkage and Temperature Reinforcement List Moderate
Column bar end left end Column bar end end
List # mm mm mm # mm mm mm List List List Degree of Restraint in Primary Direction % 0
1 Bar 1 0 0 40 3 0 0 40 40 20 32 Degree of Restraint in Secondary Direction % 0
Concrete Strength Gain Rate List N
Layer Minimum Maximum Minimum % in
Number Number of Spacing of Steel area as Flange Concrete Tensile Strength for Deflection Calculations- #.## x (Fc)n #.# -1
Bars Bars % Maximum Value of Ieff/Igross for Deflection Calculations #.# 0.6
# mm % % Total Deflection Warning Limit - Maximum Span/Deflection #.# 250
1 0 0 0 0 Total Deflection Warning Limit - Maximum Deflection mm 40
Incremental Deflection Warning Limit - Maximum Span/Deflection #.# 360
Incremental Deflection Warning Limit - Maximum Deflection mm 25
Design Zones Initial Time for Shrinkage List Full Shrinkage
Layer Steel Left End Distance to Bar stagger Bottom Right End Distance to Bar stagger Bottom Maximum Minimum Preferred Time of Loading in days #.# 10
Number type Reference left end of length at left Cover at left Reference right end of length at right Cover at Bar Size Bar Size bar size Age Adjustment Factor #.# 0.76
Column bar end end Column bar end Right End Concrete Strength at Time of Loading MPa 27.04
List # mm mm mm # mm mm mm List List List Loaded Period in years #.# 30
1 Bar 1 0 0 40 3 0 0 40 40 20 32 Tension stiffening Approach List Modified Concrete Tensile Modulus Method
Material Properties
Reinforcement Design Zones Concrete : Standard Concrete : Concrete Strength Basis - Cube
Description A C32/40MPa
1 2
mm Characteristic Compressive Strength MPa 40
0 Mean Compressive Strength MPa 50
Lower Characteristic Tensile Strength MPa 2.12
-200
Upper Characteristic Tensile Strength MPa 3.93
-400 Concrete Density kg/m3 2447
Design Concrete Modulus MPa 31186.6
-600 Mean Concrete Modulus MPa 33345.8
Basic Shrinkage Strain mm/mm 0
-800 #.#
Shrinkage Multiplier 1
Basic Creep Factor #.# 2.656
0 6100mm #.#
Creep Multiplier 1
Design Data Concrete Strain at Peak Stress #.# 0.002
Capacity Reduction factor (phi) for Flexure #.# 1 Squash Load Factor #.# 0.85
Capacity Reduction factor (phi) for Shear #.# 1 Concrete Strain Limit #.# 0.004
Capacity Reduction factor (phi) for Shear with transverse reinf #.# 1 Strength Gain Rate List Normal
Material Factor for Concrete in Flexure #.# 1.5 Maximum Aggregate Size mm 20
Material Factor for Concrete in Shear #.# 1.5
Material Factor for Reinforcement #.# 1.15
Maximum Ratio of Neutral Axis Depth for Ductility #.# 0.58
Ductility Limit - Strain #.# 0
Reinforcement Bar
Designation Type Yield Elastic Ductility Peak Peak Design Material Material Material Capacity Material Capacity Include as Description
Ductility Check at Left End Column Y/N Y
Stress Modulus Strain Stress Strain Factor Factor Reduction Factor Reduction Factor Flexural
Ductility Check at Right End Column Y/N Y Limit Flexure Shear - Flexure - Shear Reinforcement for
Minimum Reinforcement Strength Limit - #.## x M* #.# 0 Shear
Flexural Critical Section - Consider Transverse Beams Y/N Y H Deformed 500 2.05e5 N 0.05 540 90 -1 -1 -1 -1 Y
Flexural Critical Section - Distance from centre of Support #.# -1
Beam Left Sideface Cover (Internal) mm 25
Beam Right Sideface cover mm 40 Nominal Bar Bar Area Bar Bar Stock
Prestress Minimum Reinforcement Basis List Program Default Bar Size Diameter Inertia Weight Length
Shear Enhancement at Supports Y/N N A mm mm2 mm4 kg/m mm
Ast Value in Shear Calculations List Calculated 10 10 78.5 491.07 0.62 12000
RAPT 6.6.8.0 Project Name: J110 Page 7/18 RAPT 6.6.8.0 Project Name: J110 Page 8/18
Licensee: AECOM Singapore Pte Ltd 1/6/2022 7:27:02 PM License No.: 10479063400712WPN11 Licensee: AECOM Singapore Pte Ltd 1/6/2022 7:27:06 PM License No.: 10479063400712WPN11
Frame Description: G/C/8,G/C/8-1 Frame Description: G/C/8,G/C/8-1
Nominal Bar Bar Area Bar Bar Stock Col No. 1 Self Extra Dead Live
Bar Size Diameter Inertia Weight Length Weight Load Load
A mm mm2 mm4 kg/m mm Reaction kN 173.29 49.27 50.68
13 13 132.7 1402.55 1.04 12000 Elastic Rotation #.# 1.96e-4 0 0
16 16 201.1 3218.29 1.58 12000 Elastic Axial Shortening mm -0 -0 -0
20 20 314.2 7857.14 2.47 12000
22 22 380.1 11503.6 2.98 12000 Col No. 2 Self Extra Dead Live
25 25 490.9 19182.5 3.85 12000 Weight Load Load
32 32 804.2 51492.6 6.31 12000 Moment Above kNm -0 -0 -0
40 40 1256.6 1.257e5 9.86 12000 Moment Below kNm 0 0 0
Reaction kN 299.39 98.1 114.07
Elastic Rotation #.# -1.58e-4 0 0
Elevation view
Elastic Axial Shortening mm -0 -0 -0
1 2
mm
0
Load Combinations
-200
Column Actions
-400 Col No. 1 Characteristic Characteristic Service Service Ultimate Ultimate Ultimate Ultimate
Service Service (Reversal) Flexure Flexure Shear Shear
-600 (Reversal) (Reversal) (Reversal)
Moment Above kNm 0 0 0 0 0 0 0 0
-800 Moment Below kNm 0 0 0 0 0 0 0 0
Reaction kN 273.24 273.24 247.91 247.91 376.48 376.48 213.86 385.19
0 6100mm Elastic Rotation #.# 3.2e-4 3.2e-4 2.87e-4 2.87e-4 4.41e-4 4.41e-4 2.35e-4 4.6e-4
Elastic Axial Shortening mm -0 -0 -0 -0 -0.1 -0.1 -0 -0.1
Plan view
Col No. 2 Characteristic Characteristic Service Service Ultimate Ultimate Ultimate Ultimate
mm 1 2
Service Service (Reversal) Flexure Flexure Shear Shear
-0 (Reversal) (Reversal) (Reversal)
Moment Above kNm 0 0 0 0 0 0 0 0
300
Moment Below kNm 0 0 0 0 0 0 0 0
600 Reaction kN 511.57 511.57 454.53 454.53 707.73 707.73 457.2 707.73
Elastic Rotation #.# -2.69e-4 -2.69e-4 -2.42e-4 -2.42e-4 -3.71e-4 -3.71e-4 -1.68e-4 -3.71e-4
900 Elastic Axial Shortening mm -0.1 -0.1 -0.1 -0.1 -0.2 -0.2 -0.1 -0.2
1200
1500
0 6100mm Ultimate Design
Flexure
Full Elevation View
1 2
1 2 kNm
mm -300
0 -114 -157
-200
-100
-500 0 85.2
100
-1000 200
300
400
-1500 500
600 524
-2000 0 6100mm
0 6100mm
Warnings Moment Moment 1 Moment 2
Input
No errors or warnings were found. 1 2
kN
Output 400
No errors or warnings were found. 164 147
200
0
-200
Bending Moments -400 -253
Load Cases -600
Column Actions 0 6100mm
Col No. 1 Self Extra Dead Live
Weight Load Load Shear Shear 1 Shear 2
Moment Above kNm -0 -0 -0
Moment Below kNm 0 0 0
RAPT 6.6.8.0 Project Name: J110 Page 9/18 RAPT 6.6.8.0 Project Name: J110 Page 10/18
Licensee: AECOM Singapore Pte Ltd 1/6/2022 7:27:10 PM License No.: 10479063400712WPN11 Licensee: AECOM Singapore Pte Ltd 1/6/2022 7:27:14 PM License No.: 10479063400712WPN11
Frame Description: G/C/8,G/C/8-1 Frame Description: G/C/8,G/C/8-1
Shear
1 2
0.062
0.057
1 2 0.08
kNm
-300 0.06
-200 -157 0.04
-89.1
-100 0.02
0 85.2
0
100
200 -0.02
300 -0.04
400 -0.06
0.054
500 387
600 0 6100mm
0 6100mm
Neutral Axis Depth Initial Final
Moment Moment 1 Moment 2
Span 1
Design Comments:-
1 2 - As there is no area of steel in the tension zone (any prestressing tendons are in the compression zone) we are now adding an area of steel, equivalent to
kN that required for minimum reinforcement, to the design tension layer. This is then assumed to be the initial design reinforcement setup. More reinforcement will
400 be added as required to achieve the applied moments. Ast added = 1519.45mm2 @ 5651mm
168 147
200
0
Service
-200
Maximum Moment Condition
-400 -269
-600 1 2
MPa MPa
0 6100mm -3 -2.17 -0.61 -180
-2 -120
Shear Shear 1 Shear 2 -1 -60
0 0
1 60
Flexural Design 2 120
Ultimate 3 180
4 240
mm21 2 5 300
1.85 0.69
24000 1710 0 6100mm
1800
1200 Gross Stress Top Gross Stress Bottom Cracked Compression Reinforcement Tension Limits
600
0 Reversal Moment Condition
-600
-1200 1 2
MPa MPa
-1800 -3 -1.77 -0.53 -180
-2400 2026 0 -2 -120
0 6100mm -1 -60
0 0
Reinforcement Top Total Bottom Total Top Ultimate Bottom Ultimate Min Top Min Bot 1 60
2 120
3 180
1 2 4 240
kNm
-800 5 1.52 0.59 300
-600 0 6100mm
-400
-200 Gross Stress Top Gross Stress Bottom Cracked Compression Reinforcement Tension Limits
0
200 Span 1
400 Design Comments:-
600 - Increase in stress from decompression to working exceeds 200MPa in at least one steel layer. Reinforcement has been added to reduce stress change
800 below this maximum value. Refer RAPT manual Section T.7.6
0 6100mm
Gross Stress Top Gross Stress Bottom Cracked Compression Reinforcement Tension Limits 173.5 346.9 520.4 260.2 3 Minimum Steel
173.5 346.9 520.4 260.2 3 Minimum Steel
173.5 346.9 520.4 260.2 3 Minimum Steel
Characteristic Service 173.5 346.9 520.4 260.2 3 Minimum Steel
Maximum Moment Condition 173.5 346.9 520.4 260.2 3 Minimum Steel
173.5 346.9 520.4 260.2 3 Minimum Steel
MPa1 2 MPa 173.5 346.9 520.4 260.2 3 Minimum Steel
-4 -2.49 -0.7 -400 173.5 346.9 520.4 260.2 3 Minimum Steel
-2 -200 173.5 346.9 520.4 260.2 3 Minimum Steel
173.5 346.9 520.4 260.2 3 Minimum Steel
0 0 173.5 346.9 520.4 260.2 3 Minimum Steel
2 200 173.5 346.9 520.4 260.2 3 Minimum Steel
173.5 346.9 520.4 260.2 3 Minimum Steel
4 400 173.5 346.9 520.4 260.2 3 Minimum Steel
6 600 173.5 346.9 520.4 260.2 3 Minimum Steel
2.13 0.79
0 6100mm
Gross Stress Top Gross Stress Bottom Cracked Compression Reinforcement Tension Limits
Span 2
Reversal Moment Condition Locat V* Mv* Pv Mdec d Ast bv phi Vuc phi Vut phi Vu Phi Vumax phi VuMin phi Vus Theta Asv/s
MPa1 2 MPa
-4 -400 mm kN kNm kN kNm mm mm2 mm kN kN kN kN kN kN #.# mm2/mm
-1.71 -0.53
225 189.86 -156.91 0 0 844 1538.28 1000 0 0 0 4239.18 0 0 0
-2 -200 945 147.13 -35.59 0 0 844 1538.28 1000 302.94 99999 302.94 4239.18 747.35 0 21.8 0.91
0 0 1100 137.93 -13.5 0 0 844 1538.28 1000 302.94 99999 302.94 4239.18 747.35 0 21.8 0.91
2 200
Spacing of Sets Minimum Legs Shear Comments
4 400 2 legs 4 legs 6 legs Min legs
6 600 H10 H10 H10 H10
1.47 0.59 mm mm mm mm # A
0 6100mm
173.5 346.9 520.4 260.2 3 Minimum Steel
Gross Stress Top Gross Stress Bottom Cracked Compression Reinforcement Tension Limits 173.5 346.9 520.4 260.2 3 Minimum Steel
RAPT 6.6.8.0 Project Name: J110 Page 13/18 RAPT 6.6.8.0 Project Name: J110 Page 14/18
Licensee: AECOM Singapore Pte Ltd 1/6/2022 7:27:24 PM License No.: 10479063400712WPN11 Licensee: AECOM Singapore Pte Ltd 1/6/2022 7:27:28 PM License No.: 10479063400712WPN11
Frame Description: G/C/8,G/C/8-1 Frame Description: G/C/8,G/C/8-1
Punching Total Long Term
Column Head Critical Section
Column Bh a at u d fcv P/A Asw/s min V* Mv* V*eff VRd1 VRd2 Asv result mm1 2
No. 4
A #.# mm mm mm mm MPa MPa mm2/mm kN kNm kN kN kN mm2 A
2
1 1 1913 900 1500 844 0.36 0 0 385.19 0 385.19 454.41 1664.72 0 OK
2 1 3113 900 1500 844 0.36 0 0 707.73 0 707.73 454.41 3329.44 1145.85 O K with Ties 0 1.36
-2
-4 -2.53
-6
Deflections 2406 880
All Spans Loaded 0 6100mm
Transfer
Even Spans Loaded Odd Spans Loaded All Spans Loaded
mm1 2
4 Even Spans Loaded
2 Transfer
0
0.314 mm1 2
-2 -0.597 4
-4 2
-6 0
10218 3822 0.314
-2 -0.597
0 6100mm
-4
Short Term
-6
10218 3822
mm1 2
0 6100mm
4
2 Short Term
0
0.46 mm1 2
-2 -0.84 4
-4 2
-6 0
7259 2609 0.375
-2 -0.716
0 6100mm
-4
Even Spans Loaded Odd Spans Loaded All Spans Loaded
-6
Incremental 8521 3200
0 6100mm
mm1 2
All Spans Loaded Odd Spans Loaded Even Spans Loaded
4
2 Incremental
0 1.06
mm1 2
-2 4
-1.97
-4 2
-6 0 0.98
3102 1127
0 6100mm -2
-1.84
-4
Even Spans Loaded Odd Spans Loaded All Spans Loaded
-6
3312 1225
0 6100mm
mm1 2 mm1 2
4 4
2 2
0 1.28 0 1.4
-2 -2
-2.41 -2.56
-4 -4
-6 -6
2531 939 2380 859
0 6100mm 0 6100mm
All Spans Loaded Odd Spans Loaded Even Spans Loaded All Spans Loaded Even Spans Loaded Odd Spans Loaded
0 1.1
-2
-1.99
-4
0.91 173.5 346.9 520.4 260.2 3 Minimum Steel
-6 0.91 173.5 346.9 520.4 260.2 3 Minimum Steel
3059 1093
0.91 173.5 346.9 520.4 260.2 3 Minimum Steel
0 6100mm
0.91 173.5 346.9 520.4 260.2 3 Minimum Steel
All Spans Loaded Even Spans Loaded Odd Spans Loaded 0.91 173.5 346.9 520.4 260.2 3 Minimum Steel
0.91 173.5 346.9 520.4 260.2 3 Minimum Steel
0.91 173.5 346.9 520.4 260.2 3 Minimum Steel
0.91 173.5 346.9 520.4 260.2 3 Minimum Steel
0.91 173.5 346.9 520.4 260.2 3 Minimum Steel
0.91 173.5 346.9 520.4 260.2 3 Minimum Steel
0.91 173.5 346.9 520.4 260.2 3 Minimum Steel
0.91 173.5 346.9 520.4 260.2 3 Minimum Steel
0.91 173.5 346.9 520.4 260.2 3 Minimum Steel
0.91 173.5 346.9 520.4 260.2 3 Minimum Steel
RAPT 6.6.8.0 Project Name: J110 Page 17/18 RAPT 6.6.8.0 Project Name: J110 Page 18/18
Licensee: AECOM Singapore Pte Ltd 1/6/2022 7:27:40 PM License No.: 10479063400712WPN11 Licensee: AECOM Singapore Pte Ltd 1/6/2022 7:27:44 PM License No.: 10479063400712WPN11
Frame Description: G/C/8,G/C/8-1 Frame Description: G/C/8,G/C/8-1
Shear Reinforcement - - Column Grid 2 - Required Bar Size is smaller than the Preferred Bar Size. Maintaining the same cover will require slightly less reinforcement than
Spacing of Sets calculated.
2 legs 4 legs 6 legs Min legs Minimum Shear - - Span 1 - Required Bar Size is smaller than the Preferred Bar Size. Maintaining the same cover will require slightly less reinforcement than calculated.
Area H10 H10 H10 H10 Legs Comments Design Comments:-
mm2/mm mm mm mm mm # A - Span - 1 - Reinforcement added at left span contraflexure point for Offset of Bending Moment Diagram for Shear - 1107.32mm2
0.91 173.5 346.9 520.4 260.2 3 Minimum Steel - Span - 1 - Reinforcement added at right span contraflexure point for Offset of Bending Moment Diagram for Shear - 1403.01mm2
- - Column Grid 2 - Required Bar Size is smaller than the Preferred Bar Size. Maintaining the same cover will require slightly less reinforcement than
calculated.
Design Comments:-
- - Column Grid 2 - Required Bar Size is smaller than the Preferred Bar Size. Maintaining the same cover will require slightly less reinforcement than
calculated.
- - Span 1 - Required Bar Size is smaller than the Preferred Bar Size. Maintaining the same cover will require slightly less reinforcement than calculated.
- Span - 1 - Reinforcement added at right support contraflexure point for Offset of Bending Moment Diagram for Shear - 318.45mm2
- Span - 1 - Reinforcement added at left span contraflexure point for Offset of Bending Moment Diagram for Shear - 1107.32mm2
- Span - 1 - Reinforcement added at right span contraflexure point for Offset of Bending Moment Diagram for Shear - 1403.01mm2
Span 2
Top Reinforcement Bottom Reinforcement
Design Comments:-
- - Column Grid 2 - Required Bar Size is smaller than the Preferred Bar Size. Maintaining the same cover will require slightly less reinforcement than
calculated.
Reinforcement Layout
4-H25
1 2
mm
0
-200
-400
-600
-800
7-H20
0 6100mm
RAPT 6.6.8.0 Project Name: J110 Page 2/17
Licensee: AECOM Singapore Pte Ltd 1/6/2022 7:20:16 PM License No.: 10479063400712WPN11
Project Name: J110 Beams
Project Number: G/8A/B-7 Beam Beam Beam Beam Effective
Designer: SLT Number Depth Width Width Flange
C:\Users\sujeevanleonard.tham\OneDrive - AECOM\Projects\J110\J110\OneDrive_2021-07-01\12. Southern at Width
Slab
Staircase\Design Files\Str\Beams\G,J.A,8,1, G,J.A,8,2 .rpf mm mm mm mm
1 900 750 750 750
RAPT - Version: 6.6.8.0 RC 900 750 750 2390
Reinforced And Post-Tensioned Concrete Analysis & Design Package
Copyright(C) 1988 - 2021 PCDC Pty. Ltd. All Rights Reserved
Load Cases
Licensee Load Load Type Load Definition Live Load Description
AECOM Singapore Pte Ltd Case Deflection Case
300 Beach Road
#03-00 The Concourse List List Y/N A
Singapore 199555 1 Self Weight Applied Loads
10479063400712WPN11 2 Extra Dead Load Applied Loads
3 Live Load Applied Loads Y
Due to the different Concrete Strength types in the Design Standard and Materials in this run, the concrete strengths shown in the materials data have been
multiplied in the calculatiuons by 0.8 2. Extra Dead Load - Point
Load Reference Distance to Load Load Description
Span column Load from Length
Span Span Slab Panel Panel reference
Length Depth Width Width column
Left Right # mm kN mm A
mm mm mm mm 1 2 900 130 0
LE 0
1 7100 350 2000 2000
RC 4100 350 2000 2000 3. Live Load - Panel
Load Left End Left end of Load at Right Right end of Load at Live Description
reference load from left end End load from right Load
Columns column reference reference reference end reduction
column column column
Column Column Support Transverse Transverse
# mm kN/m2 # mm kN/m2 #.# A
Grid Type Column prestress
Reference spacing (P/A) 1 1 0 5 2 4100 5 1 LL
A List mm MPa
1 1 Knife-Edge 2000
2 2 Knife-Edge 2000
RAPT 6.6.8.0 Project Name: J110 Page 3/17 RAPT 6.6.8.0 Project Name: J110 Page 4/17
Licensee: AECOM Singapore Pte Ltd 1/6/2022 7:20:20 PM License No.: 10479063400712WPN11 Licensee: AECOM Singapore Pte Ltd 1/6/2022 7:20:23 PM License No.: 10479063400712WPN11
3. Live Load - Point Load Case 1 : 1. Self Weight
Load Reference Distance to Load Load Live Description
column Load from Length Load kN/m1 2 kN
reference reduction 32 200
column 1
24 150
# mm kN mm #.# A 16 100
1 2 900 80 0 1 8 50
0 0
0 7100mm
32 L1 L2 200
Load Combinations : Ultimate 24 150
Load Description 1. Self 2. Extra 3. 16 100
Combination Weight Dead Live 8 50
0 0
Load Load
A #.# #.# #.# 1 2
1 Live Load 1.35 1.35 1.5
2 Live Load 1 1 1.5 Load Case 2 : 2. Extra Dead Load
3 Dead Load 1.425 1.425 0
kN/m1 2 kN
32 200
Load Combinations : Short Term Service 24 1 150
16 100
Load Description 1. Self 2. Extra 3. Live 8 50
Combination Weight Dead Load Load 0 0
A #.# #.# #.# 0 7100mm
1 Live Load 1 1 0.5 32 200
24 150
16 100
8 P1 P1 50
Load Combinations : Permanent Service 0 0
Load Description 1. Self 2. Extra 3. Live 1 2
Combination Weight Dead Load Load
A #.# #.# #.#
1 Live Load 1 1 0.3
Load Case 3 : 3. Live Load
kN/m1 2 kN
32 200
Load Combinations : Deflection 24 150
Load Description 1. Self 2. Extra 3. Live 16 1 100
Combination Weight Dead Load Load 8 50
A #.# #.# #.# 0 0
0 7100mm
1 Short Term - Deflection 1 1 0.5
32 200
2 Permanent - Deflection 1 1 0.3 24 150
3 Initial - Deflection 1 0 0 16 P1 P1 100
8 50
0 0
1 2
Load Combinations : Transfer Prestress
Load Description 1. Self 2. Extra 3. Live Reinforcement
Combination Weight Dead Load Load Reinforcement Reinforcement Preferred Number
A #.# #.# #.# Use Type Bar Size of Legs
1 Transfer 1 0 0 List List #
Flexural Bar H 500MPa
Flexural Mesh A 500MPa
Load Combinations : Pre Existing Shear Option 1 H 500MPa 10 2
Load Description 1. Self 2. Extra 3. Live Shear Option 2 H 500MPa 10 4
Combination Weight Dead Load Load Shear Option 3 H 500MPa 10 6
A #.# #.# #.# Punching Shear H 500MPa 10 2
1 Pre Existing 1 0 0
Reinforcement
Load Combinations : Construction Maximum Minimum Minimum Minimum Span Minimum Span Infill Stagger
Load Description 1. Self 2. Extra 3. Live Bar Bar Continuous Reinforcement Reinforcement Bars Bars
Combination Weight Dead Load Load Spacing Spacing Reinforcement into End into Internal
A #.# #.# #.# Support Support
1 Construction 1 0 0 mm mm #.# #.# #.# Y/N Y/N
Support Reinforcement 300 60 0 N N
Span Reinforcement 300 60 0 0 N N
RAPT 6.6.8.0 Project Name: J110 Page 5/17 RAPT 6.6.8.0 Project Name: J110 Page 6/17
Licensee: AECOM Singapore Pte Ltd 1/6/2022 7:20:27 PM License No.: 10479063400712WPN11 Licensee: AECOM Singapore Pte Ltd 1/6/2022 7:20:30 PM License No.: 10479063400712WPN11
Design Zones
Layer Steel Left End Distance to Bar stagger Top Right End Distance to Bar stagger Top Cover Maximum Minimum Preferred AS3600 Shrinkage and Temperature Reinforcement List Moderate
Number type Reference left end of length at left Cover at Reference right end of length at right at Right Bar Size Bar Size bar size Degree of Restraint in Primary Direction % 0
Column bar end left end Column bar end end Degree of Restraint in Secondary Direction % 0
List # mm mm mm # mm mm mm List List List List
Concrete Strength Gain Rate N
1 Bar 1 0 0 40 3 0 0 40 40 20 32
Concrete Tensile Strength for Deflection Calculations- #.## x (Fc)n #.# -1
Layer Minimum Maximum Minimum % in #.#
Maximum Value of Ieff/Igross for Deflection Calculations 0.6
Number Number of Spacing of Steel area as Flange
Total Deflection Warning Limit - Maximum Span/Deflection #.# 250
Bars Bars %
# mm % % Total Deflection Warning Limit - Maximum Deflection mm 40
1 0 0 0 0 Incremental Deflection Warning Limit - Maximum Span/Deflection #.# 360
Incremental Deflection Warning Limit - Maximum Deflection mm 25
Initial Time for Shrinkage List Full Shrinkage
Time of Loading in days #.# 10
Design Zones Age Adjustment Factor #.# 0.76
Layer Steel Left End Distance to Bar stagger Bottom Right End Distance to Bar stagger Bottom Maximum Minimum Preferred Concrete Strength at Time of Loading MPa 27.04
Number type Reference left end of length at left Cover at left Reference right end of length at right Cover at Bar Size Bar Size bar size
Loaded Period in years #.# 30
Column bar end end Column bar end Right End
List # mm mm mm # mm mm mm List List List Tension stiffening Approach List Modified Concrete Tensile Modulus Method
1 Bar 1 0 0 40 3 0 0 40 40 20 32
Live Load Pattern Factor #.# 1
Layer Minimum Maximum Minimum % in Pattern Live Load for Ultimate Strength Y/N Y
Number Number of Spacing of Steel area as Flange Pattern Live Load for Crack Control Y/N Y
Bars Bars % Pattern Live Load For Deflections Y/N Y
# mm % % Pattern Live Load for Deflection Permanent Load Combination Y/N N
1 0 0 0 0
Material Properties
Concrete : Standard Concrete : Concrete Strength Basis - Cube
Reinforcement Design Zones Description A C32/40MPa
Characteristic Compressive Strength MPa 40
1 2 Mean Compressive Strength MPa 50
mm
Lower Characteristic Tensile Strength MPa 2.12
0
Upper Characteristic Tensile Strength MPa 3.93
-200 Concrete Density kg/m3 2447
Design Concrete Modulus MPa 31186.6
-400 Mean Concrete Modulus MPa 33345.8
-600 Basic Shrinkage Strain mm/mm 0
Shrinkage Multiplier #.# 1
-800 Basic Creep Factor #.# 2.656
Creep Multiplier #.# 1
0 7100mm Concrete Strain at Peak Stress #.# 0.002
Design Data Squash Load Factor #.# 0.85
Capacity Reduction factor (phi) for Flexure #.# 1 Concrete Strain Limit #.# 0.004
Capacity Reduction factor (phi) for Shear #.# 1 Strength Gain Rate List Normal
Capacity Reduction factor (phi) for Shear with transverse reinf #.# 1 Maximum Aggregate Size mm 20
Material Factor for Concrete in Flexure #.# 1.5
Material Factor for Concrete in Shear #.# 1.5
Material Factor for Reinforcement #.# 1.15 Reinforcement Bar
Maximum Ratio of Neutral Axis Depth for Ductility #.# 0.58 Designation Type Yield Elastic Ductility Peak Peak Design Material Material Material Capacity Material Capacity Include as Description
Ductility Limit - Strain #.# 0 Stress Modulus Strain Stress Strain Factor Factor Reduction Factor Reduction Factor Flexural
Ductility Check at Left End Column Y/N Y Limit Flexure Shear - Flexure - Shear Reinforcement for
Ductility Check at Right End Column Y/N Y Shear
Minimum Reinforcement Strength Limit - #.## x M* #.# 0 H Deformed 500 2.05e5 N 0.05 540 90 -1 -1 -1 -1 Y
Flexural Critical Section - Consider Transverse Beams Y/N Y
Flexural Critical Section - Distance from centre of Support #.# -1
Beam Left Sideface Cover (Internal) mm 25 Nominal Bar Bar Area Bar Bar Stock
Beam Right Sideface cover mm 40 Bar Size Diameter Inertia Weight Length
Prestress Minimum Reinforcement Basis List Program Default A mm mm2 mm4 kg/m mm
Shear Enhancement at Supports Y/N N 10 10 78.5 491.07 0.62 12000
Ast Value in Shear Calculations List Calculated 13 13 132.7 1402.55 1.04 12000
Limit Reinforcement Strain Y/N Y 16 16 201.1 3218.29 1.58 12000
Include Strain Hardening of Reinforcement Y/N N 20 20 314.2 7857.14 2.47 12000
Beam Shear Critical Section Location List Code Critical Section 22 22 380.1 11503.6 2.98 12000
25 25 490.9 19182.5 3.85 12000
32 32 804.2 51492.6 6.31 12000
40 40 1256.6 1.257e5 9.86 12000
Maximum Service Stress Change - Prestressed Sections MPa 200
Maximum Service Stress Change - Reinforced Sections MPa 200
Relative Humidity % 50
Average Temperature C. 20
Prestress Losses Calculations based on List Program Default
Crack Width Calculations List .20 mm
RAPT 6.6.8.0 Project Name: J110 Page 7/17 RAPT 6.6.8.0 Project Name: J110 Page 8/17
Licensee: AECOM Singapore Pte Ltd 1/6/2022 7:20:34 PM License No.: 10479063400712WPN11 Licensee: AECOM Singapore Pte Ltd 1/6/2022 7:20:37 PM License No.: 10479063400712WPN11
Elevation view Col No. 2 Characteristic Characteristic Service Service Ultimate Ultimate Ultimate Ultimate
Service Service (Reversal) Flexure Flexure Shear Shear
1 2 (Reversal) (Reversal) (Reversal)
mm Moment Above kNm 0 0 0 0 0 0 0 0
0 Moment Below kNm 0 0 0 0 0 0 0 0
Reaction kN 783.83 783.83 694.59 694.59 1084.94 1084.94 658.6 1084.94
-200
Elastic Rotation #.# 6.45e-4 6.45e-4 5.73e-4 5.73e-4 8.92e-4 8.92e-4 3.53e-4 8.92e-4
-400 Elastic Axial Shortening mm 0 0 0 0 0 0 0 0
-600
-6 -180
-4 -120
0.2
-2 -60
0.16 0 0
0.12 2 60
0.08 4 120
0.04 6 180
8 240
0
10 5.44 4.5 300
-0.04
0 7100mm
0.051
-0.08
0 7100mm Gross Stress Top Gross Stress Bottom Cracked Compression Reinforcement Tension Limits
Gross Stress Top Gross Stress Bottom Cracked Compression Reinforcement Tension Limits
Span 2
Locat V* Mv* Pv Mdec d Ast bv phi Vuc phi Vut phi Vu Phi Vumax phi VuMin phi Vus Theta Asv/s
Reversal Moment Condition
1 2
MPa MPa mm kN kNm kN kNm mm mm2 mm kN kN kN kN kN kN #.# mm2/mm
-9 -4.73 -2.47 -300 1 741.06 -945.85 0 0 844 3915.25 750 0 0 0 3179.38 0 0 0
-6 -200 720 698.42 -428.36 0 0 844 2028.41 750 245.36 99999 245.36 3179.38 560.51 698.42 21.8 0.85
-3 -100 899 687.81 -304.29 0 0 844 2028.41 750 245.36 99999 245.36 3179.38 560.51 687.81 21.8 0.83
0 0 901 189.69 -303.41 0 0 844 2028.41 750 245.36 99999 245.36 3179.38 560.51 0 21.8 0.68
3 100 1025 182.34 -280.34 0 0 844 2028.41 750 245.36 99999 245.36 3179.38 560.51 0 21.8 0.68
6 200 1366 162.12 -221.61 0 0 844 2028.41 750 245.36 99999 245.36 3179.38 560.51 0 21.8 0.68
9 300 1707 141.9 -169.78 0 0 844 2028.41 750 245.36 99999 245.36 3179.38 560.51 0 21.8 0.68
12 400 2050 121.56 -124.6 0 0 844 2028.41 750 245.36 99999 245.36 3179.38 560.51 0 21.8 0.68
15 4.99 4.14 500 2393 101.22 -86.39 0 0 844 2028.41 750 245.36 99999 245.36 3179.38 560.51 0 21.8 0.68
0 7100mm
2734 81 -55.32 0 0 844 2028.41 750 245.36 99999 245.36 3179.38 560.51 0 21.8 0.68
Gross Stress Top Gross Stress Bottom Cracked Compression Reinforcement Tension Limits 3075 60.78 -31.15 0 0 844 2028.41 750 245.36 99999 245.36 3179.38 560.51 0 21.8 0.68
3384 42.46 -15.2 0 0 844 2028.41 750 245.36 99999 245.36 3179.38 560.51 0 21.8 0.68
3692 24.19 -4.94 0 0 844 2028.41 750 245.36 99999 245.36 3179.38 560.51 0 21.8 0.68
Shear Design 4000 5.93 -0.3 0 0 844 2028.41 750 245.36 99999 245.36 3179.38 560.51 0 21.8 0.68
Beam
Span 1 Spacing of Sets Minimum Legs Shear Comments
Locat V* Mv* Pv Mdec d Ast bv phi Vuc phi Vut phi Vu Phi Vumax phi VuMin phi Vus Theta Asv/s 2 legs 4 legs 6 legs Min legs
H10 H10 H10 H10
mm mm mm mm # A
mm kN kNm kN kNm mm mm2 mm kN kN kN kN kN kN #.# mm2/mm
100 104.22 10.72 0 0 844 982.07 750 0 0 0 3179.38 0 0 0 185.6 371.2 556.8 278.4 3
720 67.46 63.94 0 0 844 982.07 750 227.21 99999 227.21 3179.38 560.51 0 21.8 0.68 188.5 377 565.4 282.7 3
983 52.69 74.54 0 0 844 982.07 750 227.21 99999 227.21 3179.38 560.51 0 21.8 0.68 231.3 462.6 600 346.9 3 Minimum Steel
1246 37.1 86.35 0 0 844 982.07 750 227.21 99999 227.21 3179.38 560.51 0 21.8 0.68 231.3 462.6 600 346.9 3 Minimum Steel
1509 -43.74 -9.67 0 0 844 981.46 750 227.21 99999 227.21 3179.38 560.51 0 21.8 0.68 231.3 462.6 600 346.9 3 Minimum Steel
1775 -58.02 -9.58 0 0 844 981.46 750 227.21 99999 227.21 3179.38 560.51 0 21.8 0.68 231.3 462.6 600 346.9 3 Minimum Steel
2366 -84.2 -51.61 0 0 844 981.46 750 227.21 99999 227.21 3179.38 560.51 0 21.8 0.68 231.3 462.6 600 346.9 3 Minimum Steel
2957 -114.54 -91.87 0 0 844 982.07 750 227.21 99999 227.21 3179.38 560.51 0 21.8 0.68 231.3 462.6 600 346.9 3 Minimum Steel
3550 -146.64 -146.91 0 0 844 982.07 750 227.21 99999 227.21 3179.38 560.51 0 21.8 0.68 231.3 462.6 600 346.9 3 Minimum Steel
4143 -175.97 -220.16 0 0 844 982.07 750 227.21 99999 227.21 3179.38 560.51 0 21.8 0.68 231.3 462.6 600 346.9 3 Minimum Steel
4734 -206.86 -314.82 0 0 844 1377.52 750 227.21 99999 227.21 3179.38 560.51 0 21.8 0.68 231.3 462.6 600 346.9 3 Minimum Steel
5325 -241.9 -447.43 0 0 844 1886.94 750 239.52 99999 239.52 3179.38 560.51 241.9 21.8 0.68 231.3 462.6 600 346.9 3 Minimum Steel
5591 -255.18 -499.92 0 0 844 2143.13 750 249.9 99999 249.9 3179.38 560.51 255.18 21.8 0.68 231.3 462.6 600 346.9 3 Minimum Steel
5854 -270.77 -569.08 0 0 844 2412.97 750 259.98 99999 259.98 3179.38 560.51 270.77 21.8 0.68
6117 -286.37 -642.35 0 0 844 2699.33 750 269.88 99999 269.88 3179.38 560.51 286.37 21.8 0.68
6380 -301.13 -714.4 0 0 844 3002.37 750 279.62 99999 279.62 3179.38 560.51 301.13 21.8 0.68
7099 -343.77 -946.25 0 0 844 3916.83 750 0 0 0 3179.38 0 0 0
Punching
Spacing of Sets Minimum Legs Shear Comments Column Head Critical Section
2 legs 4 legs 6 legs Min legs Column Bh a at u d fcv P/A Asw/s min V* Mv* V*eff VRd1 VRd2 Asv result
H10 H10 H10 H10 No.
mm mm mm mm # A A #.# mm mm mm mm MPa MPa mm2/mm kN kNm kN kN kN mm2 A
1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Check Not Carried Out!
231.3 462.6 600 346.9 3 Minimum Steel 2 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Check Not Carried Out!
231.3 462.6 600 346.9 3 Minimum Steel
231.3 462.6 600 346.9 3 Minimum Steel
231.3 462.6 600 346.9 3 Minimum Steel
231.3 462.6 600 346.9 3 Minimum Steel
231.3 462.6 600 346.9 3 Minimum Steel
231.3 462.6 600 346.9 3 Minimum Steel
231.3 462.6 600 346.9 3 Minimum Steel
RAPT 6.6.8.0 Project Name: J110 Page 13/17 RAPT 6.6.8.0 Project Name: J110 Page 14/17
Licensee: AECOM Singapore Pte Ltd 1/6/2022 7:20:54 PM License No.: 10479063400712WPN11 Licensee: AECOM Singapore Pte Ltd 1/6/2022 7:20:57 PM License No.: 10479063400712WPN11
Deflections Even Spans Loaded
All Spans Loaded Transfer
Transfer
1 2
1 2 mm
mm 0
0.443
0 -3.5
0.443
-3.5 -20
-20
-40
-40
-60 16010 1171
16010 1171 0 7100mm
-60
0 7100mm
Short Term
Short Term
1 2
1 2 mm
mm 0
1.66
0
1.42 -9.22
-20
-8.53
-20
-40
-40
-60 4288 445
5007 480 0 7100mm
-60
0 7100mm
All Spans Loaded Odd Spans Loaded Even Spans Loaded
Even Spans Loaded Odd Spans Loaded All Spans Loaded
Incremental
Incremental
1 2
1 2 mm
mm 0 3.19
0
2.94
-20 -17.1
-20 -16.4
-40
-40
-60 2223 239
2417 249 0 7100mm
-60
0 7100mm
All Spans Loaded Odd Spans Loaded Even Spans Loaded
Even Spans Loaded Odd Spans Loaded All Spans Loaded
Total Long Term
Total Long Term
1 2
1 2 mm
mm 0 3.6
0 3.34
-20
-20 -20.4
-19.7
-40
-40
-60 1974 201
2125 208 0 7100mm
-60
0 7100mm
All Spans Loaded Odd Spans Loaded Even Spans Loaded
Even Spans Loaded Odd Spans Loaded All Spans Loaded
RAPT 6.6.8.0 Project Name: J110 Page 15/17 RAPT 6.6.8.0 Project Name: J110 Page 16/17
Licensee: AECOM Singapore Pte Ltd 1/6/2022 7:21:01 PM License No.: 10479063400712WPN11 Licensee: AECOM Singapore Pte Ltd 1/6/2022 7:21:04 PM License No.: 10479063400712WPN11
Odd Spans Loaded Top Reinforcement Bottom Reinforcement
Transfer
Max Max Section Max Max Section
1 2 Locat Size Space Area Depth Width Rebar Reqd Size Space Area Depth Width Rebar Reqd
mm mm mm mm2 mm mm A mm mm mm2 mm mm A
mm 720 0 0 981.46 56 750 2 H25 @ 640 25 300 982.07 844 750 4 H20 @ 215
0
0.443 983 0 0 981.46 56 750 2 H25 @ 640 25 300 982.07 844 750 4 H20 @ 215
-3.5 1246 0 0 981.46 56 750 2 H25 @ 640 25 300 982.07 844 750 4 H20 @ 215
-20 1509 0 0 981.46 56 750 2 H25 @ 640 25 300 982.07 844 750 4 H20 @ 215
1775 0 0 981.46 56 750 2 H25 @ 640 25 300 982.07 844 750 4 H20 @ 215
-40 2366 25 300 981.46 56 750 2 H25 @ 640 25 300 982.07 844 750 4 H20 @ 215
2957 25 300 982.07 56 750 3 H25 @ 320 25 300 981.46 844 750 4 H20 @ 215
16010 1171 3550 25 300 982.07 56 750 3 H25 @ 320 0 0 981.46 844 750 4 H20 @ 215
-60 4143 16 159.8 1287.42 56 750 3 H25 @ 320 0 0 0 844 750 No Steel Added
0 7100mm
4734 16 150.8 1667.73 56 750 4 H25 @ 213.3 0 0 0 844 750 No Steel Added
Short Term 5325 16 150.6 2111.94 56 750 5 H25 @ 160 0 0 0 844 750 No Steel Added
5591 16 150.6 2322.24 56 750 5 H25 @ 160 0 0 0 844 750 No Steel Added
1 2 5854 16 150.6 2548.46 56 750 6 H25 @ 128 0 0 0 844 750 No Steel Added
6117 16 150.6 2786.19 56 750 6 H25 @ 128 0 0 0 844 750 No Steel Added
mm
0 6380 16 150.6 3002.37 56 750 7 H25 @ 106.7 0 0 0 844 750 No Steel Added
0.856 6621 16 150.6 3294.91 56 750 7 H25 @ 106.7 0 0 0 844 750 No Steel Added
-6.03 6860 16 150.6 3599.02 56 750 8 H25 @ 91.4 0 0 0 844 750 No Steel Added
-20 7099 16 150.5 3916.83 56 750 8 H25 @ 91.4 0 0 0 844 750 No Steel Added
Shear Reinforcement
-40 Spacing of Sets
2 legs 4 legs 6 legs Min legs Minimum Shear
8291 680 Area H10 H10 H10 H10 Legs Comments
-60 mm2/mm mm mm mm mm # A
0 7100mm
All Spans Loaded Even Spans Loaded Odd Spans Loaded Max Max Section Max Max Section
Locat Size Space Area Depth Width Rebar Reqd Size Space Area Depth Width Rebar Reqd
mm mm mm mm2 mm mm A mm mm mm2 mm mm A
Detailed Reinforcement 1 16 150.5 3915.25 56 2000 8 H25 @ 91.4 0 0 0 844 750 No Steel Added
Span 1 144 16 150.5 3461.01 56 2000 8 H25 @ 91.4 0 0 0 844 750 No Steel Added
Top Reinforcement Bottom Reinforcement 287 16 150.5 3015.45 56 2000 7 H25 @ 106.7 0 0 0 844 750 No Steel Added
430 16 150.6 2790.53 56 2000 6 H25 @ 128 0 0 0 844 750 No Steel Added
Max Max Section Max Max Section 573 16 150.6 2790.53 56 2000 6 H25 @ 128 0 0 0 844 750 No Steel Added
Locat Size Space Area Depth Width Rebar Reqd Size Space Area Depth Width Rebar Reqd 720 16 189.2 2790.53 56 2000 6 H25 @ 128 0 0 0 844 750 No Steel Added
mm mm mm mm2 mm mm A mm mm mm2 mm mm A 899 25 300 2790.53 56 2000 6 H25 @ 128 0 0 0 844 750 No Steel Added
100 0 0 0 56 750 No Steel Added 25 300 982.07 844 750 4 H20 @ 215 901 25 300 2028.41 56 2000 5 H25 @ 160 0 0 0 844 750 No Steel Added
410 0 0 0 56 750 No Steel Added 25 300 982.07 844 750 4 H20 @ 215 1025 25 300 2028.41 56 2000 5 H25 @ 160 0 0 0 844 750 No Steel Added
RAPT 6.6.8.0 Project Name: J110 Page 17/17
Licensee: AECOM Singapore Pte Ltd 1/6/2022 7:21:07 PM License No.: 10479063400712WPN11
Top Reinforcement Bottom Reinforcement
Design Comments:-
- - Column Grid 2 - Required Bar Size is smaller than the Preferred Bar Size. Maintaining the same cover will require slightly less reinforcement than
calculated.
Reinforcement Layout
1 2
8-H25
mm
0
-200
-400
-600
-800
4-H20
0 7100mm
- - Column Grid 2 - Required Bar Size is smaller than the Preferred Bar Size. Maintaining the same cover will require slightly less reinforcement than
calculated.
- - Span 1 - Required Bar Size is smaller than the Preferred Bar Size. Maintaining the same cover will require slightly less reinforcement than calculated.
Design Comments:-
- Span - 1 - Reinforcement added at left span contraflexure point for Offset of Bending Moment Diagram for Shear - 283.94mm2
- Span - 1 - Reinforcement added at right span contraflexure point for Offset of Bending Moment Diagram for Shear - 271.79mm2
- - Column Grid 2 - Required Bar Size is smaller than the Preferred Bar Size. Maintaining the same cover will require slightly less reinforcement than
calculated.
CONCOURSE LEVEL RC
BEAM DESIGN
RAPT 6.6.8.0 Project Name: J110 Page 2/14
Licensee: AECOM Singapore Pte Ltd 1/6/2022 8:54:48 PM License No.: 10479063400712WPN11
Frame Description: C/7/A/1
Project Name: J110 Beams
Project Number: 60628288 Beam Beam Beam Beam Effective
Frame Description: C/7/A/1 Number Depth Width Width Flange
Designer: SLT at Width
Slab
C:\Users\sujeevanleonard.tham\OneDrive - AECOM\Projects\J110\J110\OneDrive_2021-07-01\12. Southern mm mm mm mm
Staircase\Design Files\Str\Beams\Concourse level RC beams\C,7,A1.rpf 1 700 400 400 400
Reinforcement
Load Combinations : Pre Existing Maximum Minimum Minimum Minimum Span Minimum Span Infill Stagger
Load Description 1. Self 2. Extra 3. Live Bar Bar Continuous Reinforcement Reinforcement Bars Bars
Combination Weight Dead Load Load Spacing Spacing Reinforcement into End into Internal
A #.# #.# #.# Support Support
1 Pre Existing 1 0 0 mm mm #.# #.# #.# Y/N Y/N
Support Reinforcement 300 60 0 N N
Span Reinforcement 300 60 0 0 N N
Load Combinations : Construction
Load Description 1. Self 2. Extra 3. Live
Combination Weight Dead Load Load Design Zones
A #.# #.# #.# Layer Steel Left End Distance to Bar stagger Top Right End Distance to Bar stagger Top Cover Maximum Minimum Preferred
1 Construction 1 0 0 Number type Reference left end of length at left Cover at Reference right end of length at right at Right Bar Size Bar Size bar size
Column bar end left end Column bar end end
List # mm mm mm # mm mm mm List List List
1 Bar 1 0 0 40 2 0 0 40 40 20 32
Load Case 1 : 1. Self Weight
Layer Minimum Maximum Minimum % in
kN/m1 2kN
Number Number of Spacing of Steel area as Flange
8 1 80 Bars Bars %
6 60 # mm % %
4 40
2 20 1 0 0 0 0
0 0
0 2200mm
8 L1 80
6 60
4 40
2 20
0 0
1 2
RAPT 6.6.8.0 Project Name: J110 Page 5/14 RAPT 6.6.8.0 Project Name: J110 Page 6/14
Licensee: AECOM Singapore Pte Ltd 1/6/2022 8:54:57 PM License No.: 10479063400712WPN11 Licensee: AECOM Singapore Pte Ltd 1/6/2022 8:55:00 PM License No.: 10479063400712WPN11
Frame Description: C/7/A/1 Frame Description: C/7/A/1
Design Zones Reinforcement Design Zones User Defined
Layer Steel Left End Distance to Bar stagger Bottom Right End Distance to Bar stagger Bottom Maximum Minimum Preferred
Number type Reference left end of length at left Cover at left Reference right end of length at right Cover at Bar Size Bar Size bar size 1 2
Column bar end end Column bar end Right End mm
List # mm mm mm # mm mm mm List List List 0
1 Bar 1 0 0 40 2 0 0 40 40 20 32
-200
Layer Minimum Maximum Minimum % in
Number Number of Spacing of Steel area as Flange -400
Bars Bars %
# mm % % -600
1 0 0 0 0
0 2200mm
Design Data
User Defined Capacity Reduction factor (phi) for Flexure #.# 1
Layer Steel type Left End Distance Bar Top % Development % Development Right End Distance Bar Top % Development Capacity Reduction factor (phi) for Shear #.# 1
Number Reference to left stagger Cover of Left End of of Left End of Bar Reference to right stagger Cover of Right End of Capacity Reduction factor (phi) for Shear with transverse reinf #.# 1
Column end of length at at left Bar in Tension in Compression Column end of length at at Right Bar in Tension
Material Factor for Concrete in Flexure #.# 1.5
bar left end end bar right end end
List # mm mm mm % % # mm mm mm % Material Factor for Concrete in Shear #.# 1.25
1 T 460MPa 1 0 0 40 0 0 2 0 0 40 0 Material Factor for Reinforcement #.# 1.15
Maximum Ratio of Neutral Axis Depth for Ductility #.# 0.5
Ductility Limit - Strain #.# 0
Layer % Development Bar Number Spacing % in Layer attached
Number of Right End of Size of Bars of Bars Flange after the Ductility Check at Left End Column Y/N Y
Bar in PreExisting Load Ductility Check at Right End Column Y/N Y
Compression Case Minimum Reinforcement Strength Limit - #.## x M* #.# 0
% List # mm % Y/N Flexural Critical Section - Consider Transverse Beams Y/N Y
1 0 20 3 0 0 N Flexural Critical Section - Distance from centre of Support #.# -1
Beam Left Sideface Cover (Internal) mm 25
Beam Right Sideface cover mm 40
Prestress Minimum Reinforcement Basis List Program Default
User Defined
Shear Enhancement at Supports Y/N Y
Layer Steel type Left End Distance Bar Bottom % Development % Development Right End Distance Bar Bottom % Development
Number Reference to left stagger Cover of Left End of of Left End of Bar Reference to right stagger Cover of Right End of Ast Value in Shear Calculations List Calculated
Column end of length at at Left Bar in Tension in Compression Column end of length at at Right Bar in Tension Maximum Shear Stress for BS8110 MPa 0
bar left end end bar right end End Limit Reinforcement Strain Y/N Y
List # mm mm mm % % # mm mm mm % Include Strain Hardening of Reinforcement Y/N N
1 T 460MPa 1 0 0 40 37.947 0 1 2200 0 40 97.24 Beam Shear Critical Section Location List Code Critical Section
Elevation view Col No. 2 Characteristic Characteristic Service Service Ultimate Ultimate Ultimate Ultimate
Service Service (Reversal) Flexure Flexure Shear Shear
1 2 (Reversal) (Reversal) (Reversal)
mm Moment Above kNm 0 0 0 0 0 0 0 0
0 kNm
Moment Below 0 0 0 0 0 0 0 0
Reaction kN 71.4 71.4 71.4 71.4 103.89 103.89 77.54 103.89
-200 Elastic Rotation #.# -1.22e-4 -1.22e-4 -1.22e-4 -1.22e-4 -1.78e-4 -1.78e-4 -1.32e-4 -1.78e-4
Elastic Axial Shortening mm 0 0 0 0 0 0 0 0
-400
-600
Ultimate Design
0 2200mm Flexure
kNm1 2
-20
mm1 2 0 10.3 10.3
-0 20
40
100
60
80
200
100
120 105
300
0 2200mm
1 2 kNm1 2
kN -60
120 102
0
90
60 60
30 120
0 180
-30 240
-60 300
-90 360
-120 -102 420
0 2200mm 0 2200mm
Shear 1 2
0.03
kNm1 2 0
-20
-0.03
0 10.3 10.3
-0.06
20
-0.09
40
-0.12
0.108
60
-0.15
80
-0.18
100 0 2200mm
120 104
0 2200mm Neutral Axis Depth Initial Final
Moment Moment 1 Moment 2
Service
Maximum Moment Condition
1 2
kN 1 2
120 102 MPa MPa
90 -2.4 -1.96 -80
60 -1.8 -60
30 -1.2 -40
0 -0.6 -20
-30 0 0
-60 0.6 20
-90 1.2 40
-120 -102 1.8 60
0 2200mm 2.4 2 80
0 2200mm
Shear Shear 1 Shear 2
Gross Stress Top Gross Stress Bottom Cracked Compression Reinforcement Tension
Flexural Design Reversal Moment Condition
Ultimate
1 2
mm21 2 MPa MPa
100 -2.4 -1.73 -80
0 0 -1.8 -60
80
60 -1.2 -40
40 -0.6 -20
20 0 0
0 0.6 20
-20 1.2 40
-40 1.8 60
-60
2.4 1.8 80
-80 0
-100 0 2200mm
0 2200mm
Gross Stress Top Gross Stress Bottom Cracked Compression Reinforcement Tension
Reinforcement Top Total Bottom Total Top Ultimate Bottom Ultimate Min Top Min Bot
RAPT 6.6.8.0 Project Name: J110 Page 11/14 RAPT 6.6.8.0 Project Name: J110 Page 12/14
Licensee: AECOM Singapore Pte Ltd 1/6/2022 8:55:14 PM License No.: 10479063400712WPN11 Licensee: AECOM Singapore Pte Ltd 1/6/2022 8:55:17 PM License No.: 10479063400712WPN11
Frame Description: C/7/A/1 Frame Description: C/7/A/1
Permanent Shear Design
Maximum Moment Condition Beam
Span 1
1 2 Locat V* Mv* Pv Mdec d Ast bv phi Vuc phi Vut phi Vu Phi Vumax phi VuMin phi Vus Theta Asv/s
MPa MPa
-2 -1.54 -80
-1.5 -60
-1 -40 mm kN kNm kN kNm mm mm2 mm kN kN kN kN kN kN #.# mm2/mm
-0.5 -20 100 102.4 10.31 0 0 647.5 0 400 1451.03 99999 1451.03 1295 1740.31 0 45 0.4
0 0 175 101.29 17.95 0 0 647.5 0 400 878.04 99999 878.04 1295 1094 0 45 0.4
0.5 20 250 100.17 25.51 0 0 647.5 0 400 645.41 99999 645.41 1295 831.6 0 45 0.4
1 40 325 99.11 32.88 0 0 647.5 0 400 518.08 99999 518.08 1295 687.98 0 45 0.4
1.5 60 400 97.99 40.27 0 0 647.5 0 400 437.15 99999 437.15 1295 596.69 0 45 0.4
2 1.57 80 475 96.87 47.57 0 0 647.5 0 400 380.83 99999 380.83 1295 533.16 0 45 0.4
0 2200mm 550 95.92 54.52 0 0 647.5 0 400 331.09 99999 331.09 1295 477.05 0 45 0.4
560 95.77 55.48 0 0 647.5 0 400 325.17 99999 325.17 1295 470.38 0 45 0.4
Gross Stress Top Gross Stress Bottom Cracked Compression Reinforcement Tension
699 93.7 68.65 0 0 647.5 0 400 260.51 99999 260.51 1295 397.45 0 45 0.4
701 93.67 68.84 0 0 647.5 0 400 259.77 99999 259.77 1295 396.61 0 45 0.4
Reversal Moment Condition
900 90.98 86.83 0 0 647.5 0 400 202.33 99999 202.33 1295 331.82 0 45 0.4
1100 -88.38 104.3 0 0 647.5 0 400 165.54 99999 165.54 1295 290.33 0 45 0.4
1 2
MPa MPa 1300 -90.98 86.83 0 0 647.5 0 400 202.33 99999 202.33 1295 331.82 0 45 0.4
-2 -1.36 -80 1499 -93.67 68.84 0 0 647.5 0 400 259.77 99999 259.77 1295 396.61 0 45 0.4
-1.5 -60 1501 -93.7 68.65 0 0 647.5 0 400 260.51 99999 260.51 1295 397.45 0 45 0.4
-1 -40 1640 -95.77 55.48 0 0 647.5 0 400 325.17 99999 325.17 1295 470.38 0 45 0.4
-0.5 -20 1650 -95.92 54.52 0 0 647.5 0 400 331.09 99999 331.09 1295 477.05 0 45 0.4
0 0
1725 -96.87 47.57 0 0 647.5 0 400 383.36 99999 383.36 1295 536.02 0 45 0.4
0.5 20
1800 -97.99 40.27 0 0 647.5 0 400 455.24 99999 455.24 1295 617.1 0 45 0.4
1 40
1875 -99.11 32.88 0 0 647.5 0 400 560.3 99999 560.3 1295 735.6 0 45 0.4
1.5 60
1950 -100.17 25.51 0 0 647.5 0 400 728.39 99999 728.39 1295 925.2 0 45 0.4
2 1.41 80
2025 -101.29 17.95 0 0 647.5 0 400 1040.56 99999 1040.56 1295 1277.31 0 45 0.4
0 2200mm
2100 -102.4 10.31 0 0 647.5 0 400 1820.97 99999 1820.97 1295 2157.59 0 45 0.4
Gross Stress Top Gross Stress Bottom Cracked Compression Reinforcement Tension
Spacing of Sets Minimum Legs Shear Comments
2 legs 4 legs 6 legs Min legs
Characteristic Service T10 T10 T10 T10
Maximum Moment Condition mm mm mm mm # A
392.5 485.6 485.6 392.5 2 Minimum Steel
1 2 392.5 485.6 485.6 392.5 2 Minimum Steel
MPa MPa
-2.7 -1.96 -90 392.5 485.6 485.6 392.5 2 Minimum Steel
-1.8 -60 392.5 485.6 485.6 392.5 2 Minimum Steel
-0.9 -30 392.5 485.6 485.6 392.5 2 Minimum Steel
0 0 392.5 485.6 485.6 392.5 2 Minimum Steel
0.9 30 392.5 485.6 485.6 392.5 2 Minimum Steel
1.8 60 392.5 485.6 485.6 392.5 2 Minimum Steel
2.7 90 392.5 485.6 485.6 392.5 2 Minimum Steel
3.6 120 392.5 485.6 485.6 392.5 2 Minimum Steel
2 392.5 485.6 485.6 392.5 2 Minimum Steel
0 2200mm 392.5 485.6 485.6 392.5 2 Minimum Steel
392.5 485.6 485.6 392.5 2 Minimum Steel
Gross Stress Top Gross Stress Bottom Cracked Compression Reinforcement Tension
392.5 485.6 485.6 392.5 2 Minimum Steel
392.5 485.6 485.6 392.5 2 Minimum Steel
Reversal Moment Condition
392.5 485.6 485.6 392.5 2 Minimum Steel
1 2 392.5 485.6 485.6 392.5 2 Minimum Steel
MPa MPa 392.5 485.6 485.6 392.5 2 Minimum Steel
-2.7 -1.73 -90 392.5 485.6 485.6 392.5 2 Minimum Steel
-1.8 -60 392.5 485.6 485.6 392.5 2 Minimum Steel
-0.9 -30 392.5 485.6 485.6 392.5 2 Minimum Steel
0 0 392.5 485.6 485.6 392.5 2 Minimum Steel
0.9 30 392.5 485.6 485.6 392.5 2 Minimum Steel
1.8 60
2.7 90
3.6 120
1.8
0 2200mm
Punching
Gross Stress Top Gross Stress Bottom Cracked Compression Reinforcement Tension Column Head Critical Section
Column Bh a at u d fcv P/A Asw/s min V* Mv* V*eff Vu Vumax Asv result
No.
A #.# mm mm mm mm MPa MPa mm2/mm kN kNm kN kN kN mm2 A
1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Check Not Carried Out!
2 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Check Not Carried Out!
RAPT 6.6.8.0 Project Name: J110 Page 13/14 RAPT 6.6.8.0 Project Name: J110 Page 14/14
Licensee: AECOM Singapore Pte Ltd 1/6/2022 8:55:20 PM License No.: 10479063400712WPN11 Licensee: AECOM Singapore Pte Ltd 1/6/2022 8:55:23 PM License No.: 10479063400712WPN11
Frame Description: C/7/A/1 Frame Description: C/7/A/1
Deflections Top Reinforcement Bottom Reinforcement
All Spans Loaded
Max Section Max Section
Transfer
Locat Space Area Depth Width Rebar Reqd Space Area Depth Width Rebar Reqd
mm mm mm2 mm mm A mm mm2 mm mm A
mm1 2
475 0 0 56 400 No Steel Added 300 0 644 400 No Steel Added
0
550 0 0 56 400 No Steel Added 300 0 644 400 No Steel Added
-0.2 -0.074 560 0 0 56 400 No Steel Added 300 0 644 400 No Steel Added
699 0 0 56 400 No Steel Added 300 0 644 400 No Steel Added
-0.4 701 0 0 56 400 No Steel Added 300 0 644 400 No Steel Added
900 0 0 56 400 No Steel Added 300 0 644 400 No Steel Added
-0.6
1100 0 0 56 400 No Steel Added 300 0 644 400 No Steel Added
-0.8 1300 0 0 56 400 No Steel Added 300 0 644 400 No Steel Added
1499 0 0 56 400 No Steel Added 300 0 644 400 No Steel Added
29620
-1 1501 0 0 56 400 No Steel Added 300 0 644 400 No Steel Added
0 2200mm
1640 0 0 56 400 No Steel Added 300 0 644 400 No Steel Added
Short Term 1650 0 0 56 400 No Steel Added 300 0 644 400 No Steel Added
1725 0 0 56 400 No Steel Added 300 0 644 400 No Steel Added
mm1 2 1800 0 0 56 400 No Steel Added 300 0 644 400 No Steel Added
0 1875 0 0 56 400 No Steel Added 300 0 644 400 No Steel Added
1950 0 0 56 400 No Steel Added 300 0 644 400 No Steel Added
-0.2 -0.133 2025 0 0 56 400 No Steel Added 300 0 644 400 No Steel Added
2100 0 0 56 400 No Steel Added 300 0 644 400 No Steel Added
-0.4 Shear Reinforcement
Spacing of Sets
-0.6
2 legs 4 legs 6 legs Min legs Minimum Shear
-0.8 Area T10 T10 T10 T10 Legs Comments
mm2/mm mm mm mm mm # A
16538
-1 0.4 392.5 485.6 485.6 392.5 2 Minimum Steel
0 2200mm
0.4 392.5 485.6 485.6 392.5 2 Minimum Steel
0.4 392.5 485.6 485.6 392.5 2 Minimum Steel
Incremental
0.4 392.5 485.6 485.6 392.5 2 Minimum Steel
mm1 2 0.4 392.5 485.6 485.6 392.5 2 Minimum Steel
0 0.4 392.5 485.6 485.6 392.5 2 Minimum Steel
0.4 392.5 485.6 485.6 392.5 2 Minimum Steel
-0.2 0.4 392.5 485.6 485.6 392.5 2 Minimum Steel
-0.265 0.4 392.5 485.6 485.6 392.5 2 Minimum Steel
-0.4 0.4 392.5 485.6 485.6 392.5 2 Minimum Steel
-0.6 0.4 392.5 485.6 485.6 392.5 2 Minimum Steel
0.4 392.5 485.6 485.6 392.5 2 Minimum Steel
-0.8 0.4 392.5 485.6 485.6 392.5 2 Minimum Steel
8308 0.4 392.5 485.6 485.6 392.5 2 Minimum Steel
-1 0.4 392.5 485.6 485.6 392.5 2 Minimum Steel
0 2200mm
0.4 392.5 485.6 485.6 392.5 2 Minimum Steel
Total Long Term 0.4 392.5 485.6 485.6 392.5 2 Minimum Steel
0.4 392.5 485.6 485.6 392.5 2 Minimum Steel
mm1 2 0.4 392.5 485.6 485.6 392.5 2 Minimum Steel
0 0.4 392.5 485.6 485.6 392.5 2 Minimum Steel
0.4 392.5 485.6 485.6 392.5 2 Minimum Steel
-0.2 0.4 392.5 485.6 485.6 392.5 2 Minimum Steel
0.4 392.5 485.6 485.6 392.5 2 Minimum Steel
-0.4 -0.334
-0.6
-0.8
6591 Reinforcement Layout
-1
0 2200mm
(3-T20)
1 2
mm
Detailed Reinforcement 0
Span 1
Top Reinforcement Bottom Reinforcement -200
(3-T25)
100 0 0 56 400 No Steel Added 300 0 644 400 No Steel Added
175 0 0 56 400 No Steel Added 300 0 644 400 No Steel Added 0 2200mm
250 0 0 56 400 No Steel Added 300 0 644 400 No Steel Added
325 0 0 56 400 No Steel Added 300 0 644 400 No Steel Added
400 0 0 56 400 No Steel Added 300 0 644 400 No Steel Added
RAPT 6.6.8.0 Project Name: J110 Page 2/14
Licensee: AECOM Singapore Pte Ltd 1/6/2022 9:19:32 PM License No.: 10479063400712WPN11
Frame Description: C/A/7A/1
Project Name: J110 Beams
Project Number: 60628288 Beam Beam Beam Beam Effective
Frame Description: C/A/7A/1 Number Depth Width Width Flange
Designer: SLT at Width
Slab
C:\Users\sujeevanleonard.tham\OneDrive - AECOM\Projects\J110\J110\OneDrive_2021-07-01\12. Southern mm mm mm mm
Staircase\Design Files\Str\Beams\Concourse level RC beams\C,A,7A,1.rpf 1 700 400 400 1200
0 10400mm
Material Properties
Reinforcement Design Zones User Defined Concrete : Standard Concrete : Concrete Strength Basis - Cube
Description A C32/40MPa
1 2 Characteristic Compressive Strength MPa 40
mm Mean Compressive Strength MPa 50
0 Lower Characteristic Tensile Strength MPa 2.12
Upper Characteristic Tensile Strength MPa 3.93
-200 Concrete Density kg/m3 2447
Design Concrete Modulus MPa 31186.6
-400 Mean Concrete Modulus MPa 33345.8
Basic Shrinkage Strain mm/mm 0
-600 Shrinkage Multiplier #.# 1
Basic Creep Factor #.# 2.656
0 10400mm Creep Multiplier #.# 1
Design Data Concrete Strain at Peak Stress #.# 0.002
#.# Squash Load Factor #.# 0.85
Capacity Reduction factor (phi) for Flexure 1
#.# Concrete Strain Limit #.# 0.004
Capacity Reduction factor (phi) for Shear 1
#.# Strength Gain Rate List Normal
Capacity Reduction factor (phi) for Shear with transverse reinf 1
#.# Maximum Aggregate Size mm 20
Material Factor for Concrete in Flexure 1.5
Material Factor for Concrete in Shear #.# 1.5
Material Factor for Reinforcement #.# 1.15
Maximum Ratio of Neutral Axis Depth for Ductility #.# 0.58 Reinforcement Bar
Ductility Limit - Strain #.# 0 Designation Type Yield Elastic Ductility Peak Peak Design Material Material Material Capacity Material Capacity Include as Description
Ductility Check at Left End Column Y/N Y Stress Modulus Strain Stress Strain Factor Factor Reduction Factor Reduction Factor Flexural
Ductility Check at Right End Column Y/N Y Limit Flexure Shear - Flexure - Shear Reinforcement for
Minimum Reinforcement Strength Limit - #.## x M* #.# 0 Shear
Y/N H Deformed 500 2.05e5 N 0.05 540 90 -1 -1 -1 -1 Y
Flexural Critical Section - Consider Transverse Beams Y
Flexural Critical Section - Distance from centre of Support #.# -1
Beam Left Sideface Cover (Internal) mm 25
Beam Right Sideface cover mm 40 Nominal Bar Bar Area Bar Bar Stock
Prestress Minimum Reinforcement Basis List Program Default Bar Size Diameter Inertia Weight Length
Y/N A mm mm2 mm4 kg/m mm
Shear Enhancement at Supports N
Ast Value in Shear Calculations List Calculated 10 10 78.5 491.07 0.62 12000
Limit Reinforcement Strain Y/N Y 13 13 132.7 1402.55 1.04 12000
Include Strain Hardening of Reinforcement Y/N N 16 16 201.1 3218.29 1.58 12000
Beam Shear Critical Section Location List Code Critical Section 20 20 314.2 7857.14 2.47 12000
22 22 380.1 11503.6 2.98 12000
25 25 490.9 19182.5 3.85 12000
32 32 804.2 51492.6 6.31 12000
Maximum Service Stress Change - Prestressed Sections MPa 150 40 40 1256.6 1.257e5 9.86 12000
Maximum Service Stress Change - Reinforced Sections MPa 200
Relative Humidity % 50
Average Temperature C. 20
Elevation view
Prestress Losses Calculations based on List Program Default
1 2
Crack Width Calculations List Code default mm
AS3600 Shrinkage and Temperature Reinforcement List Moderate 0
Degree of Restraint in Primary Direction % 0
Degree of Restraint in Secondary Direction % 0 -200
Concrete Strength Gain Rate List N
-400
Concrete Tensile Strength for Deflection Calculations- #.## x (Fc)n #.# -1
Maximum Value of Ieff/Igross for Deflection Calculations #.# 0.6 -600
Total Deflection Warning Limit - Maximum Span/Deflection #.# 250
Total Deflection Warning Limit - Maximum Deflection mm 30 0 10400mm
Incremental Deflection Warning Limit - Maximum Span/Deflection #.# 360
Incremental Deflection Warning Limit - Maximum Deflection mm 25
Initial Time for Shrinkage List Full Shrinkage
Time of Loading in days #.# 10
RAPT 6.6.8.0 Project Name: J110 Page 7/14 RAPT 6.6.8.0 Project Name: J110 Page 8/14
Licensee: AECOM Singapore Pte Ltd 1/6/2022 9:19:46 PM License No.: 10479063400712WPN11 Licensee: AECOM Singapore Pte Ltd 1/6/2022 9:19:49 PM License No.: 10479063400712WPN11
Frame Description: C/A/7A/1 Frame Description: C/A/7A/1
Plan view Ultimate Design
Flexure
mm1 2
-0 1 2
kNm
-60
300 15.1 15.1
0
60
600 120
180
900 240
300
360
1200 420
0 10400mm 397
Warnings 0 10400mm
Input
No errors or warnings were found. Moment Moment 1 Moment 2
Output kN1 2
No errors or warnings were found. 200
136
150
100
50
0
Bending Moments
-50
Load Cases -100
Column Actions -150
Col No. 1 Self Extra Dead Live -136
-200
Weight Load Load 0 10400mm
Moment Above kNm -0 -0 -0
Moment Below kNm -0 -0 -0 Shear Shear 1 Shear 2
Reaction kN 57.2 21.22 31.2
Elastic Rotation #.# 8.43e-4 3.13e-4 4.6e-4
Elastic Axial Shortening mm 0 0 0
Shear
400 -4 -80
600 -2 -40
800 0 0
1000 2 40
0 10400mm 4 80
2.93
6 120
Capacity Minimum Ultimate Design Initial Final 0 10400mm
Gross Stress Top Gross Stress Bottom Cracked Compression Reinforcement Tension
1 2
0.02 Reversal Moment Condition
0
-0.02 MPa1 2MPa
-0.04 -6 -4.56 -120
-0.06
-0.08 -4 -80
-0.1 -2 -40
-0.12
-0.14 0 0
0.131
-0.16 2 40
0 10400mm
4 80
Neutral Axis Depth Initial Final 2.93
6 120
0 10400mm
Service Gross Stress Top Gross Stress Bottom Cracked Compression Reinforcement Tension
Maximum Moment Condition
1 2 Characteristic Service
MPa MPa
-6 -4.88 -120 Maximum Moment Condition
-4 -80 1 2
-2 -40 MPa -5.69 MPa
0 0 -6 -120
-4 -80
2 40
-2 -40
4 80
0 0
6 3.13 120 2 40
0 10400mm
4 80
Gross Stress Top Gross Stress Bottom Cracked Compression Reinforcement Tension 6 3.65 120
0 10400mm
Gross Stress Top Gross Stress Bottom Cracked Compression Reinforcement Tension
RAPT 6.6.8.0 Project Name: J110 Page 11/14 RAPT 6.6.8.0 Project Name: J110 Page 12/14
Licensee: AECOM Singapore Pte Ltd 1/6/2022 9:19:58 PM License No.: 10479063400712WPN11 Licensee: AECOM Singapore Pte Ltd 1/6/2022 9:20:01 PM License No.: 10479063400712WPN11
Frame Description: C/A/7A/1 Frame Description: C/A/7A/1
Reversal Moment Condition
Spacing of Sets Minimum Legs Shear Comments
1 2 2 legs 4 legs 6 legs Min legs
MPa -5.69 MPa H10 H10 H10 H10
-6 -120 mm mm mm mm # A
-4 -80 433.7 483 483 433.7 2 Minimum Steel
-2 -40 433.7 483 483 433.7 2 Minimum Steel
433.7 483 483 433.7 2 Minimum Steel
0 0
2 40
4 80
6 3.65 120
0 10400mm
Punching
Gross Stress Top Gross Stress Bottom Cracked Compression Reinforcement Tension Column Head Critical Section
Column Bh a at u d fcv P/A Asw/s min V* Mv* V*eff VRd1 VRd2 Asv result
No.
Shear Design A #.# mm mm mm mm MPa MPa mm2/mm kN kNm kN kN kN mm2 A
Beam 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Check Not Carried Out!
Span 1 2 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Check Not Carried Out!
Locat V* Mv* Pv Mdec d Ast bv phi Vuc phi Vut phi Vu Phi Vumax phi VuMin phi Vus Theta Asv/s
-26
-40
-60
400 Reinforcement Layout
0 10400mm
(3-H20)
1 2
mm
0
Detailed Reinforcement
Span 1
-200
Top Reinforcement Bottom Reinforcement
-400
Max Max Section Max Max Section
Locat Size Space Area Depth Width Rebar Reqd Size Space Area Depth Width Rebar Reqd
mm mm mm mm2 mm mm A mm mm mm2 mm mm A -600
(3-H25)
(3-H32)
100 0 0 0 56 1200 No Steel Added 32 300 0 644 400 No Steel Added
560 0 0 0 56 1200 No Steel Added 32 300 0 644 400 No Steel Added 0 10400mm
699 0 0 0 56 1200 No Steel Added 32 300 0 644 400 No Steel Added
701 0 0 0 56 1200 No Steel Added 32 300 0 644 400 No Steel Added
1080 0 0 0 56 1200 No Steel Added 32 300 0 644 400 No Steel Added
1459 0 0 0 56 1200 No Steel Added 32 300 0 644 400 No Steel Added
1838 0 0 0 56 1200 No Steel Added 32 300 0 644 400 No Steel Added
2217 0 0 0 56 1200 No Steel Added 32 300 0 644 400 No Steel Added
2600 0 0 0 56 1200 No Steel Added 32 300 0 644 400 No Steel Added
3466 0 0 0 56 1200 No Steel Added 32 300 0 644 400 No Steel Added
4332 0 0 0 56 1200 No Steel Added 32 300 0 644 400 No Steel Added
5200 0 0 0 56 1200 No Steel Added 32 300 0 644 400 No Steel Added
6068 0 0 0 56 1200 No Steel Added 32 300 0 644 400 No Steel Added
6934 0 0 0 56 1200 No Steel Added 32 300 0 644 400 No Steel Added
7800 0 0 0 56 1200 No Steel Added 32 300 0 644 400 No Steel Added
8183 0 0 0 56 1200 No Steel Added 32 300 0 644 400 No Steel Added
8562 0 0 0 56 1200 No Steel Added 32 300 0 644 400 No Steel Added
8941 0 0 0 56 1200 No Steel Added 32 300 0 644 400 No Steel Added
9320 0 0 0 56 1200 No Steel Added 32 300 0 644 400 No Steel Added
9699 0 0 0 56 1200 No Steel Added 32 300 0 644 400 No Steel Added
9701 0 0 0 56 1200 No Steel Added 32 300 0 644 400 No Steel Added
9840 0 0 0 56 1200 No Steel Added 32 300 0 644 400 No Steel Added
10300 0 0 0 56 1200 No Steel Added 32 300 0 644 400 No Steel Added
Shear Reinforcement
Spacing of Sets
2 legs 4 legs 6 legs Min legs Minimum Shear
Area H10 H10 H10 H10 Legs Comments
mm2/mm mm mm mm mm # A
kN/m1 2kN
10 150
Load Combinations : Short Term Service 8 120
Load Description 1. Self 2. Extra 3. Live 6 90
4 5 60
Combination Weight Dead Load Load 2 3 30
A #.# #.# #.# 0 0
0 10600mm
1 Live Load 1 1 0.5
10 150
8 120
6 90
4 60
Load Combinations : Permanent Service 2 P2 30
0 0
Load Description 1. Self 2. Extra 3. Live 0 10600mm
Combination Weight Dead Load Load 10 150
A #.# #.# #.# 8 120
6 90
1 Live Load 1 1 0.3 4 60
2 P1 30
0 0
0 10600mm
RAPT 6.6.8.0 Project Name: J110-SOUTHERN STAIRCASE Page 5/16 RAPT 6.6.8.0 Project Name: J110-SOUTHERN STAIRCASE Page 6/16
Licensee: AECOM Singapore Pte Ltd 1/6/2022 8:46:46 PM License No.: 10479063400712WPN11 Licensee: AECOM Singapore Pte Ltd 1/6/2022 8:46:49 PM License No.: 10479063400712WPN11
Frame Description: C/8A/A.1/1 Frame Description: C/8A/A.1/1
10 150 Layer Minimum Maximum Minimum % in
8 120 Number Number of Spacing of Steel area as Flange
6 90 Bars Bars %
4 4 L1 60
1 2 # mm % %
2 30
0 0 1 0 0 0 0
1 2
Capacity Reduction factor (phi) for Shear with transverse reinf #.# 1 Strength Gain Rate List Normal
Material Factor for Concrete in Flexure #.# 1.5 Maximum Aggregate Size mm 20
Material Factor for Concrete in Shear #.# 1.5
Material Factor for Reinforcement #.# 1.15
Maximum Ratio of Neutral Axis Depth for Ductility #.# 0.58 Reinforcement Bar
Ductility Limit - Strain #.# 0 Designation Type Yield Elastic Ductility Peak Peak Design Material Material Material Capacity Material Capacity Include as Description
Ductility Check at Left End Column Y/N Y Stress Modulus Strain Stress Strain Factor Factor Reduction Factor Reduction Factor Flexural
Ductility Check at Right End Column Y/N Y Limit Flexure Shear - Flexure - Shear Reinforcement for
Minimum Reinforcement Strength Limit - #.## x M* #.# 0 Shear
Flexural Critical Section - Consider Transverse Beams Y/N Y H Deformed 500 2.05e5 N 0.05 540 90 -1 -1 -1 -1 Y
Flexural Critical Section - Distance from centre of Support #.# -1
Beam Left Sideface Cover (Internal) mm 25
Beam Right Sideface cover mm 40 Nominal Bar Bar Area Bar Bar Stock
Prestress Minimum Reinforcement Basis List Program Default Bar Size Diameter Inertia Weight Length
Shear Enhancement at Supports Y/N N A mm mm2 mm4 kg/m mm
Ast Value in Shear Calculations List Calculated 6 6 28.3 63.64 0.22 12000
Limit Reinforcement Strain Y/N Y 8 8 50.3 201.14 0.4 12000
Include Strain Hardening of Reinforcement Y/N N 10 10 78.5 491.07 0.62 12000
Beam Shear Critical Section Location List Code Critical Section 12 13 113.1 1018.29 0.89 12000
16 16 201.1 3218.29 1.58 12000
20 20 314.2 7857.14 2.47 12000
Maximum Service Stress Change - Prestressed Sections MPa 150 25 25 490.9 19182.5 3.85 12000
Maximum Service Stress Change - Reinforced Sections MPa 0 32 32 804.2 51492.6 6.31 12000
Relative Humidity % 50 40 40 1256.6 1.26e5 9.86 12000
Average Temperature C. 20 50 50 1963.5 3.07e5 15.41 12000
Prestress Losses Calculations based on List Program Default
Crack Width Calculations List Code default Elevation view
AS3600 Shrinkage and Temperature Reinforcement List Moderate
Degree of Restraint in Primary Direction % 0 1 2
Degree of Restraint in Secondary Direction % 0 mm
Concrete Strength Gain Rate List N 0
-200
Concrete Tensile Strength for Deflection Calculations- #.## x (Fc)n #.# -1
#.# -400
Maximum Value of Ieff/Igross for Deflection Calculations 0.6
Total Deflection Warning Limit - Maximum Span/Deflection #.# 250 -600
Total Deflection Warning Limit - Maximum Deflection mm 40
#.# -800
Incremental Deflection Warning Limit - Maximum Span/Deflection 360
Incremental Deflection Warning Limit - Maximum Deflection mm 27 -1000
Initial Time for Shrinkage List Full Shrinkage 0 10600mm
Time of Loading in days #.# 10
Age Adjustment Factor #.# 0.76 Plan view
Concrete Strength at Time of Loading MPa 27.04
#.# mm 1 2
Loaded Period in years 30
-200
Tension stiffening Approach List Modified Concrete Tensile Modulus Method
-100
Live Load Pattern Factor #.#
Pattern Live Load for Ultimate Strength Y/N
Y/N 0
Pattern Live Load for Crack Control
Pattern Live Load For Deflections Y/N
Pattern Live Load for Deflection Permanent Load Combination Y/N 100
kN1 2
Load Combinations 1000
Column Actions 800 664
Col No. 1 Characteristic Characteristic Service Service Ultimate Ultimate Ultimate Ultimate 600
Service Service (Reversal) Flexure Flexure Shear Shear 400
(Reversal) (Reversal) (Reversal) 200
Moment Above kNm 219.78 219.78 184.03 184.03 211.29 307.43 211.29 307.43 0
Moment Below kNm 219.62 219.62 183.89 183.89 211.13 307.2 211.13 307.2 -200
Reaction kN 563.05 563.05 471.04 471.04 540.1 787.73 540.1 787.73 -400
Elastic Rotation #.# 4.42e-3 4.42e-3 3.7e-3 3.7e-3 4.25e-3 6.18e-3 4.25e-3 6.18e-3 -600 -489
Elastic Axial Shortening mm -0.3 -0.3 -0.2 -0.2 -0.3 -0.4 -0.3 -0.4 0 10600mm
Col No. 2 Characteristic Characteristic Service Service Ultimate Ultimate Ultimate Ultimate Shear Shear 1 Shear 2
Service Service (Reversal) Flexure Flexure Shear Shear
(Reversal) (Reversal) (Reversal)
Moment Above kNm -188.54 -188.54 -158.01 -158.01 -263.68 -181.67 -181.67 -263.68 Flexural Design
Moment Below kNm -188.4 -188.4 -157.9 -157.9 -263.49 -181.54 -181.54 -263.49 Ultimate
Reaction kN 373.09 373.09 313.48 313.48 521.55 361.78 361.78 521.55
Elastic Rotation #.# -3.79e-3 -3.79e-3 -3.18e-3 -3.18e-3 -5.3e-3 -3.65e-3 -3.65e-3 -5.3e-3 1 2
Elastic Axial Shortening mm -0.2 -0.2 -0.2 -0.2 -0.3 -0.2 -0.2 -0.3 mm2
2355 1324
2500
2000
1500
Ultimate Design 1000
Flexure 500
0
1 2 -500
kNm -1000 0
-800 -516 -462 0 10600mm
-400
0 Reinforcement Top Total Bottom Total Top Ultimate Bottom Ultimate Min Top Min Bot
400
800
1200
1600
2000 1826
0 10600mm
RAPT 6.6.8.0 Project Name: J110-SOUTHERN STAIRCASE Page 11/16 RAPT 6.6.8.0 Project Name: J110-SOUTHERN STAIRCASE Page 12/16
Licensee: AECOM Singapore Pte Ltd 1/6/2022 8:47:05 PM License No.: 10479063400712WPN11 Licensee: AECOM Singapore Pte Ltd 1/6/2022 8:47:08 PM License No.: 10479063400712WPN11
Frame Description: C/8A/A.1/1 Frame Description: C/8A/A.1/1
Permanent
kNm1 2
Maximum Moment Condition
-1200
-600 1 2
0 MPa MPa
-16 -12.66 -240
600 -12 -180
1200 -8 -120
1800 -4 -60
2400 0 0
3000 4 60
8 120
0 10600mm 12 180
16 240
20 14.58 300
Capacity Minimum Ultimate Design Initial Final 0 10600mm
1 2 Gross Stress Top Gross Stress Bottom Cracked Compression Reinforcement Tension
0.128
0.115
0.2 Reversal Moment Condition
0.1
0 1 2
-0.1 MPa MPa
-0.2 -16 -12.66 -240
-0.3 -12 -180
-0.4 -8 -120
-0.5
-0.6 -4 -60
0.58
-0.7 0 0
-0.8 4 60
0 10600mm 8 120
12 180
Neutral Axis Depth Initial Final 16 240
20 14.58 300
Span 1 0 10600mm
Design Comments:- Gross Stress Top Gross Stress Bottom Cracked Compression Reinforcement Tension
- Compression reinforcement added at span hinge location for ductility in accordance with Eurocode 2 cl.5.5. Asc = 2355.27mm2 @ 4299mm
- As there is no area of steel in the tension zone (any prestressing tendons are in the compression zone) we are now adding an area of steel, equivalent to
that required for minimum reinforcement, to the design tension layer. This is then assumed to be the initial design reinforcement setup. More reinforcement will Span 1
be added as required to achieve the applied moments. Ast added = 432.03mm2 @ 125mm Design Comments:-
- Concrete Compression stress ratio under Permanent Load greater than .45. The compression stress should be reduced or the designer needs to allow for
Characteristic Service
non-linear creep effects.
Maximum Moment Condition
Service
1 2
Maximum Moment Condition
MPa -16.38 MPa
-18 -300
1 2
-12 -200
MPa -13.72 MPa
-15 -240 -6 -100
-10 -160 0 0
-5 -80 6 100
0 0 12 200
5 80 18 300
10 160 24 18.87 400
15 240 0 10600mm
20 15.81 320 Gross Stress Top Gross Stress Bottom Cracked Compression Reinforcement Tension
0 10600mm
Gross Stress Top Gross Stress Bottom Cracked Compression Reinforcement Tension
Reversal Moment Condition
1 2
MPa -16.38 MPa
-18 -300
1 2
-12 -200
MPa -13.72 MPa
-15 -240 -6 -100
-10 -160 0 0
-5 -80 6 100
0 0 12 200
5 80 18 300
10 160 24 18.87 400
15 240 0 10600mm
20 15.81 320 Gross Stress Top Gross Stress Bottom Cracked Compression Reinforcement Tension
0 10600mm
RAPT 6.6.8.0 Project Name: J110-SOUTHERN STAIRCASE Page 13/16 RAPT 6.6.8.0 Project Name: J110-SOUTHERN STAIRCASE Page 14/16
Licensee: AECOM Singapore Pte Ltd 1/6/2022 8:47:12 PM License No.: 10479063400712WPN11 Licensee: AECOM Singapore Pte Ltd 1/6/2022 8:47:15 PM License No.: 10479063400712WPN11
Frame Description: C/8A/A.1/1 Frame Description: C/8A/A.1/1
Shear Design
Beam Spacing of Sets Minimum Legs Shear Comments
Span 1 2 legs 4 legs 6 legs Min legs
Locat V* Mv* Pv Mdec d Ast bv phi Vuc phi Vut phi Vu Phi Vumax phi VuMin phi Vus Theta Asv/s H10 H10 H10 H10
mm mm mm mm # A
75.2 150.4 225.7 112.8 3
mm kN kNm kN kNm mm mm2 mm kN kN kN kN kN kN #.# mm2/mm
125 785.72 -516.3 0 0 847.5 1484.91 350 0 0 0 1489.86 0 0 0
845 664.41 11.88 0 0 840 0 350 199.28 99999 199.28 1476.68 260.33 664.41 21.8 0.81
899 663.54 47.74 0 0 840 0 350 199.28 99999 199.28 1476.68 260.33 663.54 21.8 0.81
901 663.51 49.06 0 0 840 0 350 199.28 99999 199.28 1476.68 260.33 663.51 21.8 0.81
Punching
1250 657.91 279.65 0 0 814.4 0 350 204.62 99999 204.62 1431.7 252.4 657.91 21.8 0.83
1599 652.5 506.87 0 0 804.3 0 350 202.51 99999 202.51 1413.95 249.27 652.5 21.8 0.83 Column Head Critical Section
1948 646.9 733.61 0 0 800 0 350 201.6 99999 201.6 1406.36 247.94 646.9 21.8 0.83 Column Bh a at u d fcv P/A Asw/s min V* Mv* V*eff VRd1 VRd2 Asv result
No.
2297 641.3 958.4 0 0 800 0 350 201.6 99999 201.6 1406.36 247.94 641.3 21.8 0.82
A #.# mm mm mm mm MPa MPa mm2/mm kN kNm kN kN kN mm2 A
2650 636.23 1179.89 0 0 800 0 350 201.6 99999 201.6 1406.36 247.94 636.23 21.8 0.81
1 2.4 0 900 350 804.2 0.72 0 0 787.73 614.64 787.73 202.48 1655.41 1462.5 O K with Ties
2899 632.24 1337.81 0 0 800 0 350 201.6 99999 201.6 1406.36 247.94 632.24 21.8 0.81
2 2.4 0 900 350 329.5 0.85 0 0 521.55 527.17 521.55 98.48 1655.4 1346.92 O K with Ties
2901 433.05 1191.43 0 0 800 0 350 201.6 99999 201.6 1406.36 247.94 433.05 21.8 0.55
3450 424.24 1426.76 0 0 800 0 350 201.6 99999 201.6 1406.36 247.94 424.24 21.8 0.54
3999 416.47 1651.75 0 0 800 0 350 201.6 99999 201.6 1406.36 247.94 416.47 21.8 0.53
4001 156.95 1475.04 0 0 800 0 350 201.6 99999 201.6 1406.36 247.94 0 21.8 0.32
4299 152.17 1521.1 0 0 800 0 350 201.6 99999 201.6 1406.36 247.94 0 21.8 0.32 Deflections
4301 -193.33 1677.27 0 0 800 0 350 201.6 99999 201.6 1406.36 247.94 0 21.8 0.32 All Spans Loaded
5300 -225.22 1494.94 0 0 800 0 350 201.6 99999 201.6 1406.36 247.94 225.22 21.8 0.32
Transfer
5599 -233.05 1426.43 0 0 800 0 350 201.6 99999 201.6 1406.36 247.94 233.05 21.8 0.32
5601 -341.97 1536.26 0 0 800 0 350 201.6 99999 201.6 1406.36 247.94 341.97 21.8 0.44
mm1 2
6526 -374.08 1236.78 0 0 800 0 350 201.6 99999 201.6 1406.36 247.94 374.08 21.8 0.48 0
7450 -404.65 904.18 0 0 800 0 350 201.6 99999 201.6 1406.36 247.94 404.65 21.8 0.52
7950 -423.78 697.08 0 0 800 0 350 201.6 99999 201.6 1406.36 247.94 423.78 21.8 0.54 -20 -8.59
8303 -434.55 563.98 0 0 800 0 350 201.6 99999 201.6 1406.36 247.94 434.55 21.8 0.56
8652 -447.9 410 0 0 800 0 350 201.6 99999 201.6 1406.36 247.94 447.9 21.8 0.57 -40
9001 -461.25 251.35 0 0 804.3 0 350 202.51 99999 202.51 1413.95 249.27 461.25 21.8 0.59
-60
9350 -473.73 94.88 0 0 814.4 0 350 204.62 99999 204.62 1431.7 252.4 473.73 21.8 0.59
9699 -487.08 -72.78 0 0 329.5 0 350 98.48 99999 98.48 579.25 102.12 487.08 28.6438 2.06 -80
9701 -487.16 -73.75 0 0 329.5 0 350 98.48 99999 98.48 579.25 102.12 487.16 28.6438 2.06
1234
9755 -489.22 -100.12 0 0 329.5 0 350 98.48 99999 98.48 579.25 102.12 489.22 28.8148 2.09 0 10600mm
10475 -516.76 -462.27 0 0 847.5 1324.46 350 0 0 0 1489.86 0 0 0
Short Term
Spacing of Sets Minimum Legs Shear Comments
2 legs 4 legs 6 legs Min legs mm1 2
H10 H10 H10 H10 0
mm mm mm mm # A
-20 -15.7
194.2 388.4 582.6 194.2 2
194.4 388.9 583.3 194.4 2 -40
194.5 388.9 583.4 194.5 2
-60
190.1 380.3 570.4 190.1 2
189.3 378.7 568 189.3 2 -80
189.9 379.9 569.8 189.9 2 674
191.6 383.2 574.8 191.6 2 0 10600mm
193.1 386.3 579.4 193.1 2
194.4 388.7 583.1 194.4 2 Incremental
283.7 567.5 600 283.7 2
289.6 579.3 600 289.6 2 mm1 2
295 590.1 600 295 2 0
495.6 600 600 495.6 2 Minimum Steel
495.6 600 600 495.6 2 Minimum Steel -20
495.6 600 600 495.6 2 Minimum Steel -23
-40
495.6 600 600 495.6 2 Minimum Steel
495.6 600 600 495.6 2 Minimum Steel -60
359.3 600 600 359.3 2
328.5 600 600 328.5 2 -80
303.7 600 600 303.7 2 460
290 579.9 600 290 2 0 10600mm
282.8 565.5 600 282.8 2
274.3 548.7 600 274.3 2
267.8 535.7 600 267.8 2
264.1 528.1 600 264.1 2
76.1 152.2 228.3 114.1 3
76.1 152.2 228.2 114.1 3
RAPT 6.6.8.0 Project Name: J110-SOUTHERN STAIRCASE Page 15/16 RAPT 6.6.8.0 Project Name: J110-SOUTHERN STAIRCASE Page 16/16
Licensee: AECOM Singapore Pte Ltd 1/6/2022 8:47:18 PM License No.: 10479063400712WPN11 Licensee: AECOM Singapore Pte Ltd 1/6/2022 8:47:21 PM License No.: 10479063400712WPN11
Frame Description: C/8A/A.1/1 Frame Description: C/8A/A.1/1
Total Long Term Shear Reinforcement
Spacing of Sets
mm1 2 2 legs 4 legs 6 legs Min legs Minimum Shear
0 Area H10 H10 H10 H10 Legs Comments
mm2/mm mm mm mm mm # A
-20 0.81 194.4 388.7 583.1 194.4 2
0.55 283.7 567.5 600 283.7 2
-40 -32.6 0.54 289.6 579.3 600 289.6 2
0.53 295 590.1 600 295 2
-60
0.32 495.6 600 600 495.6 2 Minimum Steel
-80 0.32 495.6 600 600 495.6 2 Minimum Steel
325 0.32 495.6 600 600 495.6 2 Minimum Steel
0 10600mm 0.32 495.6 600 600 495.6 2 Minimum Steel
0.32 495.6 600 600 495.6 2 Minimum Steel
0.44 359.3 600 600 359.3 2
Detailed Reinforcement 0.48 328.5 600 600 328.5 2
Span 1 0.52 303.7 600 600 303.7 2
Top Reinforcement Bottom Reinforcement 0.54 290 579.9 600 290 2
0.56 282.8 565.5 600 282.8 2
Max Max Section Max Max Section 0.57 274.3 548.7 600 274.3 2
Locat Size Space Area Depth Width Rebar Reqd Size Space Area Depth Width Rebar Reqd 0.59 267.8 535.7 600 267.8 2
mm mm mm mm2 mm mm A mm mm mm2 mm mm A 0.59 264.1 528.1 600 264.1 2
125 12 170.3 1484.91 52.5 350 4 H25 @ 80 0 0 0 847.5 400 No Steel Added 2.06 76.1 152.2 228.3 114.1 3
749 32 300 159.39 52.5 350 1 H25 @ 999 0 0 0 847.5 400 No Steel Added 2.06 76.1 152.2 228.2 114.1 3
751 32 300 155.86 52.5 350 1 H25 @ 999 0 0 0 847.5 400 No Steel Added 2.09 75.2 150.4 225.7 112.8 3
845 0 0 1822.33 52.5 350 4 H25 @ 80 32 300 0 847.5 400 No Steel Added
899 0 0 2004.87 52.5 350 5 H25 @ 60 32 300 0 847.5 400 No Steel Added
901 0 0 2011.62 52.5 350 5 H25 @ 60 32 300 0 847.5 400 No Steel Added
1250 0 0 2355.27 52.5 350 5 H25 @ 60 32 300 0 847.5 400 No Steel Added Design Comments:-
1599 0 0 2355.27 52.5 350 5 H25 @ 60 32 300 0 847.5 400 No Steel Added - Span - 1 - Reinforcement added at left support contraflexure point for Offset of Bending Moment Diagram for Shear - 63.67mm2
1948 0 0 2355.27 52.5 350 5 H25 @ 60 32 300 0 847.5 400 No Steel Added
2297 0 0 2355.27 52.5 350 5 H25 @ 60 32 300 0 847.5 400 No Steel Added
2650 0 0 2355.27 52.5 350 5 H25 @ 60 32 300 0 847.5 400 No Steel Added
2899 0 0 2355.27 52.5 350 5 H25 @ 60 32 300 0 847.5 400 No Steel Added Reinforcement Layout
2901 0 0 2355.27 52.5 350 5 H25 @ 60 32 300 0 847.5 400 No Steel Added
(4-H25)
1 2
4-H25
5-H25
3-H25
3450 0 0 2355.27 52.5 350 5 H25 @ 60 32 300 0 847.5 400 No Steel Added
mm
3999 0 0 2355.27 52.5 350 5 H25 @ 60 25 286.7 0 847.5 400 No Steel Added
0
4001 0 0 2355.27 52.5 350 5 H25 @ 60 25 286.6 0 847.5 400 No Steel Added
4299 0 0 2355.27 52.5 350 5 H25 @ 60 25 283.4 0 847.5 400 No Steel Added -200
4301 0 0 2355.27 52.5 350 5 H25 @ 60 25 283.4 0 847.5 400 No Steel Added
-400
5300 0 0 2355.27 52.5 350 5 H25 @ 60 32 300 0 847.5 400 No Steel Added
5599 0 0 2355.27 52.5 350 5 H25 @ 60 32 300 0 847.5 400 No Steel Added -600
5601 0 0 2355.27 52.5 350 5 H25 @ 60 32 300 0 847.5 400 No Steel Added
-800
(4-H40)
6526 0 0 2355.27 52.5 350 5 H25 @ 60 32 300 0 847.5 400 No Steel Added
(4-H40)
7450 0 0 2355.27 52.5 350 5 H25 @ 60 32 300 0 847.5 400 No Steel Added -1000
7950 0 0 2355.27 52.5 350 5 H25 @ 60 32 300 0 847.5 400 No Steel Added 0 10600mm
8303 0 0 2355.27 52.5 350 5 H25 @ 60 32 300 0 847.5 400 No Steel Added
8652 0 0 2355.27 52.5 350 5 H25 @ 60 32 300 0 847.5 400 No Steel Added
9001 0 0 2355.27 52.5 350 5 H25 @ 60 32 300 0 847.5 400 No Steel Added
9350 0 0 2355.27 52.5 350 5 H25 @ 60 32 300 0 847.5 400 No Steel Added
9699 32 300 0 52.5 350 No Steel Added 0 0 0 847.5 400 No Steel Added
9701 32 300 0 52.5 350 No Steel Added 0 0 0 847.5 400 No Steel Added
9755 32 300 0 52.5 350 No Steel Added 0 0 0 847.5 400 No Steel Added
10115 12 197.7 462.19 52.5 350 1 H25 @ 999 0 0 0 847.5 400 No Steel Added
10475 12 170.5 1324.46 52.5 350 3 H25 @ 120 0 0 0 847.5 400 No Steel Added
Shear Reinforcement
Spacing of Sets
2 legs 4 legs 6 legs Min legs Minimum Shear
Area H10 H10 H10 H10 Legs Comments
mm2/mm mm mm mm mm # A
0 11000 mm
Material Properties
Reinforcement Design Zones User Defined Concrete : Standard Concrete : Concrete Strength Basis - Cube
Description A C32/40MPa
1 2 Characteristic Compressive Strength MPa 40
mm Mean Compressive Strength MPa 50
0 Lower Characteristic Tensile Strength MPa 2.12
Upper Characteristic Tensile Strength MPa 3.93
-200
Concrete Density kg/m3 2447
-400 Design Concrete Modulus MPa 31186.6
Mean Concrete Modulus MPa 33345.8
-600 Basic Shrinkage Strain mm/mm 0
Shrinkage Multiplier #.# 1
-800 #.#
Basic Creep Factor 2.656
0 11000 mm Creep Multiplier #.# 1
Design Data Concrete Strain at Peak Stress #.# 0.002
#.# Squash Load Factor #.# 0.85
Capacity Reduction factor (phi) for Flexure 1
#.# Concrete Strain Limit #.# 0.004
Capacity Reduction factor (phi) for Shear 1
#.# Strength Gain Rate List Normal
Capacity Reduction factor (phi) for Shear with transverse reinf 1
#.# Maximum Aggregate Size mm 20
Material Factor for Concrete in Flexure 1.5
Material Factor for Concrete in Shear #.# 1.5
Material Factor for Reinforcement #.# 1.15
Maximum Ratio of Neutral Axis Depth for Ductility #.# 0.58 Reinforcement Bar
Ductility Limit - Strain #.# 0 Designation Type Yield Elastic Ductility Peak Peak Design Material Material Material Capacity Material Capacity Include as Description
Ductility Check at Left End Column Y/N Y Stress Modulus Strain Stress Strain Factor Factor Reduction Factor Reduction Factor Flexural
Ductility Check at Right End Column Y/N Y Limit Flexure Shear - Flexure - Shear Reinforcement for
Minimum Reinforcement Strength Limit - #.## x M* #.# 0 Shear
Y/N H Deformed 500 2.05e5 N 0.05 540 90 -1 -1 -1 -1 Y
Flexural Critical Section - Consider Transverse Beams Y
Flexural Critical Section - Distance from centre of Support #.# -1
Beam Left Sideface Cover (Internal) mm 25
Beam Right Sideface cover mm 40 Nominal Bar Bar Area Bar Bar Stock
Prestress Minimum Reinforcement Basis List Program Default Bar Size Diameter Inertia Weight Length
Y/N A mm mm2 mm4 kg/m mm
Shear Enhancement at Supports N
Ast Value in Shear Calculations List Calculated 10 10 78.5 491.07 0.62 12000
Limit Reinforcement Strain Y/N Y 13 13 132.7 1402.55 1.04 12000
Include Strain Hardening of Reinforcement Y/N N 16 16 201.1 3218.29 1.58 12000
Beam Shear Critical Section Location List Code Critical Section 20 20 314.2 7857.14 2.47 12000
22 22 380.1 11503.6 2.98 12000
25 25 490.9 19182.5 3.85 12000
32 32 804.2 51492.6 6.31 12000
Maximum Service Stress Change - Prestressed Sections MPa 150 40 40 1256.6 1.257e5 9.86 12000
Maximum Service Stress Change - Reinforced Sections MPa 0
Relative Humidity % 50
Average Temperature C. 20
Elevation view
Prestress Losses Calculations based on List Program Default
1 2
Crack Width Calculations List Code default mm
AS3600 Shrinkage and Temperature Reinforcement List Moderate 0
Degree of Restraint in Primary Direction % 0
Degree of Restraint in Secondary Direction % 0 -200
Concrete Strength Gain Rate List N
-400
Concrete Tensile Strength for Deflection Calculations- #.## x (Fc)n #.# -1 -600
Maximum Value of Ieff/Igross for Deflection Calculations #.# 0.6
Total Deflection Warning Limit - Maximum Span/Deflection #.# 250 -800
Total Deflection Warning Limit - Maximum Deflection mm 25 0 11000 mm
Incremental Deflection Warning Limit - Maximum Span/Deflection #.# 500
Incremental Deflection Warning Limit - Maximum Deflection mm 25
Initial Time for Shrinkage List Full Shrinkage
Time of Loading in days #.# 10
RAPT 6.6.8.0 Project Name: J110 Page 7/14 RAPT 6.6.8.0 Project Name: J110 Page 8/14
Licensee: AECOM Singapore Pte Ltd 1/6/2022 9:10:54 PM License No.: 10479063400712WPN11 Licensee: AECOM Singapore Pte Ltd 1/6/2022 9:10:57 PM License No.: 10479063400712WPN11
Frame Description: L/A.2/7B/2 Frame Description: L/A.2/7B/2
Plan view Ultimate Design
Flexure
mm1 2
-0
kNm1 2
300 -90
19 19
0
600 90
180
900
270
1200 360
450
1500 540
0 11000 mm 527
630
Warnings 0 11000 mm
Input
No errors or warnings were found. Moment Moment 1 Moment 2
Output 1 2
kN
Warning:Total deflection in at least one span is greater than defined limit.
240 168
180
120
60
0
Bending Moments
-60
Load Cases -120
Column Actions -180
Col No. 1 Self Extra Dead Live -168
-240
Weight Load Load 0 11000 mm
Moment Above kNm -0 -0 -0
Moment Below kNm -0 -0 -0 Shear Shear 1 Shear 2
Reaction kN 68.06 28.05 41.25
Elastic Rotation #.# 7.21e-4 2.97e-4 4.37e-4
Elastic Axial Shortening mm 0 0 0
Shear
Gross Stress Top Gross Stress Bottom Cracked Compression Reinforcement Tension
1 2
0.01 Reversal Moment Condition
0
-0.01 1 2
-0.02 MPa MPa
-6 -5.21 -150
-0.03
-0.04 -4 -100
-0.05
-2 -50
-0.06
-0.07 0 0
0.066
0 11000 mm 2 50
4 100
Neutral Axis Depth Initial Final 2.64
6 150
0 11000 mm
Service Gross Stress Top Gross Stress Bottom Cracked Compression Reinforcement Tension
Maximum Moment Condition
1 2 Characteristic Service
MPa -5.61 MPa Maximum Moment Condition
-6 -150
-4 -100 1 2
MPa MPa
-2 -50 -8 -6.6 -200
0 0 -6 -150
2 50 -4 -100
-2 -50
4 100
0 0
6 2.85 150
2 50
0 11000 mm
4 100
Gross Stress Top Gross Stress Bottom Cracked Compression Reinforcement Tension 6 150
3.35
0 11000 mm
Gross Stress Top Gross Stress Bottom Cracked Compression Reinforcement Tension
RAPT 6.6.8.0 Project Name: J110 Page 11/14 RAPT 6.6.8.0 Project Name: J110 Page 12/14
Licensee: AECOM Singapore Pte Ltd 1/6/2022 9:11:06 PM License No.: 10479063400712WPN11 Licensee: AECOM Singapore Pte Ltd 1/6/2022 9:11:09 PM License No.: 10479063400712WPN11
Frame Description: L/A.2/7B/2 Frame Description: L/A.2/7B/2
Reversal Moment Condition
Spacing of Sets Minimum Legs Shear Comments
1 2 2 legs 4 legs 6 legs Min legs
MPa MPa
-6.6 H10 H10 H10 H10
-8 -200
mm mm mm mm # A
-6 -150
578.2 586.1 586.1 578.2 2 Minimum Steel
-4 -100
578.2 586.1 586.1 578.2 2 Minimum Steel
-2 -50
578.2 586.1 586.1 578.2 2 Minimum Steel
0 0
2 50
4 100
6 150
3.35
0 11000 mm
Punching
Gross Stress Top Gross Stress Bottom Cracked Compression Reinforcement Tension Column Head Critical Section
Column Bh a at u d fcv P/A Asw/s min V* Mv* V*eff VRd1 VRd2 Asv result
No.
Shear Design A #.# mm mm mm mm MPa MPa mm2/mm kN kNm kN kN kN mm2 A
Beam 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Check Not Carried Out!
Span 1 2 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Check Not Carried Out!
Locat V* Mv* Pv Mdec d Ast bv phi Vuc phi Vut phi Vu Phi Vumax phi VuMin phi Vus Theta Asv/s
Span 1
Design Comments:-
- Total Deflection greater than user defined limit = -25.3mm Reinforcement Layout
(3-H20)
1 2
mm
Detailed Reinforcement 0
Span 1 -200
Top Reinforcement Bottom Reinforcement
-400
Max Max Section Max Max Section
Locat Size Space Area Depth Width Rebar Reqd Size Space Area Depth Width Rebar Reqd -600
mm mm mm mm2 mm mm A mm mm mm2 mm mm A
-800
(2-H25)
(3-H25)
100 0 0 0 56 1400 No Steel Added 32 300 0 794 300 No Steel Added
680 0 0 0 56 1400 No Steel Added 32 300 0 794 300 No Steel Added 0 11000 mm
849 0 0 0 56 1400 No Steel Added 32 300 0 794 300 No Steel Added
851 0 0 0 56 1400 No Steel Added 32 300 0 794 300 No Steel Added
1230 0 0 0 56 1400 No Steel Added 32 300 0 794 300 No Steel Added
1609 0 0 0 56 1400 No Steel Added 32 300 0 794 300 No Steel Added
1988 0 0 0 56 1400 No Steel Added 32 300 0 794 300 No Steel Added
2367 0 0 0 56 1400 No Steel Added 32 300 0 794 300 No Steel Added
2750 0 0 0 56 1400 No Steel Added 32 300 0 794 300 No Steel Added
3666 0 0 0 56 1400 No Steel Added 25 299.7 0 794 300 No Steel Added
4582 0 0 0 56 1400 No Steel Added 25 281.2 0 794 300 No Steel Added
5500 0 0 0 56 1400 No Steel Added 25 275.4 0 794 300 No Steel Added
6418 0 0 0 56 1400 No Steel Added 25 281.2 0 794 300 No Steel Added
7334 0 0 0 56 1400 No Steel Added 25 299.7 0 794 300 No Steel Added
8250 0 0 0 56 1400 No Steel Added 32 300 0 794 300 No Steel Added
8633 0 0 0 56 1400 No Steel Added 32 300 0 794 300 No Steel Added
9012 0 0 0 56 1400 No Steel Added 32 300 0 794 300 No Steel Added
9391 0 0 0 56 1400 No Steel Added 32 300 0 794 300 No Steel Added
9770 0 0 0 56 1400 No Steel Added 32 300 0 794 300 No Steel Added
10149 0 0 0 56 1400 No Steel Added 32 300 0 794 300 No Steel Added
10151 0 0 0 56 1400 No Steel Added 32 300 0 794 300 No Steel Added
10320 0 0 0 56 1400 No Steel Added 32 300 0 794 300 No Steel Added
10900 0 0 0 56 1400 No Steel Added 32 300 0 794 300 No Steel Added
Shear Reinforcement
Spacing of Sets
2 legs 4 legs 6 legs Min legs Minimum Shear
Area H10 H10 H10 H10 Legs Comments
mm2/mm mm mm mm mm # A
Due to the different Concrete Strength types in the Design Standard and Materials in this run, the concrete strengths shown in the materials data have been Load Combinations : Short Term Service
multiplied in the calculatiuons by 0.8 Load Description 1. Self 2. Extra 3. Live
Combination Weight Dead Load Load
Span A #.# #.# #.#
Span Span Slab Panel Panel 1 Live Load 1 1 0.5
Length Depth Width Width
Left Right
mm mm mm mm
Load Combinations : Permanent Service
LE 0
Load Description 1. Self 2. Extra 3. Live
1 4500 350 1000 1000
Combination Weight Dead Load Load
RE 0 A #.# #.# #.#
1 Live Load 1 1 0.3
Columns
Column Column Support Transverse Transverse Load Combinations : Deflection
Grid Type Column prestress
Load Description 1. Self 2. Extra 3. Live
Reference spacing (P/A)
Combination Weight Dead Load Load
A List mm MPa
A #.# #.# #.#
1 1 Knife-Edge 1000
1 Short Term - Deflection 1 1 0.5
2 2 Knife-Edge 1000
2 Permanent - Deflection 1 1 0.3
3 Initial - Deflection 1 0 0
RAPT 6.6.8.0 Project Name: J110 Page 3/13 RAPT 6.6.8.0 Project Name: J110 Page 4/13
Licensee: AECOM Singapore Pte Ltd 1/6/2022 6:52:17 PM License No.: 10479063400712WPN11 Licensee: AECOM Singapore Pte Ltd 1/6/2022 6:52:20 PM License No.: 10479063400712WPN11
Frame Description: STAIRCASE SLAB Frame Description: STAIRCASE SLAB
Load Combinations : Transfer Prestress Design Zones
Load Description 1. Self 2. Extra 3. Live Layer Steel Left End Distance to Bar stagger Top Right End Distance to Bar stagger Top Cover Maximum Minimum Preferred
Combination Weight Dead Load Load Number type Reference left end of length at left Cover at Reference right end of length at right at Right Bar Size Bar Size bar size
A #.# #.# #.# Column bar end left end Column bar end end
1 Transfer 1 0 0 List # mm mm mm # mm mm mm List List List
1 Bar 1 0 0 35 2 0 0 35 25 10 13
Design Zones
Load Combinations : Construction
Layer Steel Left End Distance to Bar stagger Bottom Right End Distance to Bar stagger Bottom Maximum Minimum Preferred
Load Description 1. Self 2. Extra 3. Live Number type Reference left end of length at left Cover at left Reference right end of length at right Cover at Bar Size Bar Size bar size
Combination Weight Dead Load Load Column bar end end Column bar end Right End
A #.# #.# #.# List # mm mm mm # mm mm mm List List List
1 Construction 1 0 0 1 Bar 1 0 0 35 2 0 0 35 25 10 13
kN/m1 2
-100
10
8
6 -200
4 P1
2
0
0 4500mm -300
Col No. 1 Characteristic Characteristic Service Service Ultimate Ultimate Ultimate Ultimate 1 2
Service Service (Reversal) Flexure Flexure Shear Shear kN
(Reversal) (Reversal) (Reversal) 60 44.7
Elastic Rotation #.# 5.18e-4 5.18e-4 4.38e-4 4.38e-4 7.23e-4 7.23e-4 5.11e-4 7.23e-4 40
Elastic Axial Shortening mm 0 0 0 0 0 0 0 0 20
0
Col No. 2 Characteristic Characteristic Service Service Ultimate Ultimate Ultimate Ultimate
-20
Service Service (Reversal) Flexure Flexure Shear Shear
(Reversal) (Reversal) (Reversal) -40
Moment Above kNm 0 0 0 0 0 0 0 0 -60 -44.7
Moment Below kNm 0 0 0 0 0 0 0 0 0 4500mm
Reaction kN 36.56 36.56 30.94 30.94 51.05 51.05 36.07 51.05
Elastic Rotation #.# -5.18e-4 -5.18e-4 -4.38e-4 -4.38e-4 -7.23e-4 -7.23e-4 -5.11e-4 -7.23e-4 Shear Shear 1 Shear 2
Elastic Axial Shortening mm 0 0 0 0 0 0 0 0
Flexural Design
Ultimate
Ultimate Design
Flexure 1 2
mm2
2000 0
kNm1 2
100
-10 0
0 4.99 4.99 -100
10 -200
20 -300
-400
30
-500
40 -600 543
50
0 4500mm
60
57.4
0 4500mm Reinforcement Top Total Bottom Total Top Ultimate Bottom Ultimate Min Top Min Bot
0.056
30 -0.063
40 0 4500mm
50
47.9 Neutral Axis Depth Initial Final
60
0 4500mm
MPa1 2MPa 1 2
MPa MPa
-3 -240
-1.67 -3 -1.97 -240
-2 -160 -2 -160
-1 -80 -1 -80
0 0 0 0
1 80 1 80
2 160 2 160
3 240
3 240 4 320
4 320 5 400
5 400 6 480
6 1.69 480 7 2 560
0 4500mm 0 4500mm
Gross Stress Top Gross Stress Bottom Cracked Compression Reinforcement Tension Gross Stress Top Gross Stress Bottom Cracked Compression Reinforcement Tension
MPa1 2MPa 1 2
MPa MPa
-3 -240
-1.67 -3 -1.97 -240
-2 -160 -2 -160
-1 -80 -1 -80
0 0 0 0
1 80 1 80
2 160 2 160
3 240
3 240 4 320
4 320 5 400
5 400 6 480
6 1.69 480 7 2 560
0 4500mm 0 4500mm
Gross Stress Top Gross Stress Bottom Cracked Compression Reinforcement Tension Gross Stress Top Gross Stress Bottom Cracked Compression Reinforcement Tension
0 0 0 0 0 No shear steel
0 0 0 0 0 No shear steel
0 0 0 0 0 No shear steel
0 0 0 0 0 No shear steel
0 0 0 0 0 No shear steel
RAPT 6.6.8.0 Project Name: J110 Page 11/13 RAPT 6.6.8.0 Project Name: J110 Page 12/13
Licensee: AECOM Singapore Pte Ltd 1/6/2022 6:52:41 PM License No.: 10479063400712WPN11 Licensee: AECOM Singapore Pte Ltd 1/6/2022 6:52:44 PM License No.: 10479063400712WPN11
Frame Description: STAIRCASE SLAB Frame Description: STAIRCASE SLAB
Incremental
Spacing of Sets Minimum Legs Shear Comments
2 legs 4 legs 6 legs Min legs mm1 2
H10 H10 H10 H10 0
mm mm mm mm # A
0 0 0 0 0 No shear steel -2
0 0 0 0 0 No shear steel -2.48
0 0 0 0 0 No shear steel -4
0 0 0 0 0 No shear steel
-6
0 0 0 0 0 No shear steel
0 0 0 0 0 No shear steel -8
0 0 0 0 0 No shear steel 1816
0 0 0 0 0 No shear steel 0 4500mm
0 0 0 0 0 No shear steel
0 0 0 0 0 No shear steel Total Long Term
0 0 0 0 0 No shear steel
0 0 0 0 0 No shear steel mm1 2
0
-2
-4 -3.12
Punching
-6
Column Head Critical Section
Column Bh a at u d fcv P/A Asw/s min V* Mv* V*eff VRd1 VRd2 Asv result -8
No. 1442
A #.# mm mm mm mm MPa MPa mm2/mm kN kNm kN kN kN mm2 A 0 4500mm
1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Check Not Carried Out!
2 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Check Not Carried Out!
Detailed Reinforcement
Span 1
Top Reinforcement Bottom Reinforcement
Design Comments:-
- Span - 1 - Reinforcement added at left span contraflexure point for Offset of Bending Moment Diagram for Shear - 146.71mm2
- Span - 1 - Reinforcement added at right span contraflexure point for Offset of Bending Moment Diagram for Shear - 146.71mm2
Reinforcement Layout
1 2
mm
0
-100
-200
-300
5-H13
0 4500mm
RAPT 6.6.8.0 Project Name: J110 Page 2/13
Licensee: AECOM Singapore Pte Ltd 1/6/2022 6:55:25 PM License No.: 10479063400712WPN11
Frame Description: STAIRCASE SLAB
Project Name: J110 Load Cases
Frame Description: STAIRCASE SLAB Load Load Type Load Definition Live Load Description
Designer: SLT Case Deflection Case
C:\Users\sujeevanleonard.tham\OneDrive - AECOM\Projects\J110\J110\OneDrive_2021-07-01\12. Southern
List List Y/N A
Staircase\Design Files\Str\Slabs\Ground Slab (GA83).rpf
1 Self Weight Applied Loads
2 Extra Dead Load Applied Loads
RAPT - Version: 6.6.8.0 3 Live Load Applied Loads Y
Reinforced And Post-Tensioned Concrete Analysis & Design Package
Copyright(C) 1988 - 2021 PCDC Pty. Ltd. All Rights Reserved
1. Self Weight - Panel
Licensee Load Left End Left end of Load at Right Right end of Load at Description
AECOM Singapore Pte Ltd reference load from left end End load from right
300 Beach Road column reference reference reference end
#03-00 The Concourse column column column
Singapore 199555 # mm kN/m2 # mm kN/m2 A
10479063400712WPN11 1 1 0 8.75 2 0 8.75
Due to the different Concrete Strength types in the Design Standard and Materials in this run, the concrete strengths shown in the materials data have been Load Combinations : Short Term Service
multiplied in the calculatiuons by 0.8 Load Description 1. Self 2. Extra 3. Live
Combination Weight Dead Load Load
Span A #.# #.# #.#
Span Span Slab Panel Panel 1 Live Load 1 1 0.5
Length Depth Width Width
Left Right
mm mm mm mm
Load Combinations : Permanent Service
LE 0
Load Description 1. Self 2. Extra 3. Live
1 3000 350 1000 1000
Combination Weight Dead Load Load
RE 0 A #.# #.# #.#
1 Live Load 1 1 0.3
Columns
Column Column Support Transverse Transverse Load Combinations : Deflection
Grid Type Column prestress
Load Description 1. Self 2. Extra 3. Live
Reference spacing (P/A)
Combination Weight Dead Load Load
A List mm MPa
A #.# #.# #.#
1 1 Knife-Edge 1000
1 Short Term - Deflection 1 1 0.5
2 2 Knife-Edge 1000
2 Permanent - Deflection 1 1 0.3
3 Initial - Deflection 1 0 0
RAPT 6.6.8.0 Project Name: J110 Page 3/13 RAPT 6.6.8.0 Project Name: J110 Page 4/13
Licensee: AECOM Singapore Pte Ltd 1/6/2022 6:55:29 PM License No.: 10479063400712WPN11 Licensee: AECOM Singapore Pte Ltd 1/6/2022 6:55:33 PM License No.: 10479063400712WPN11
Frame Description: STAIRCASE SLAB Frame Description: STAIRCASE SLAB
Load Combinations : Transfer Prestress Design Zones
Load Description 1. Self 2. Extra 3. Live Layer Steel Left End Distance to Bar stagger Top Right End Distance to Bar stagger Top Cover Maximum Minimum Preferred
Combination Weight Dead Load Load Number type Reference left end of length at left Cover at Reference right end of length at right at Right Bar Size Bar Size bar size
A #.# #.# #.# Column bar end left end Column bar end end
1 Transfer 1 0 0 List # mm mm mm # mm mm mm List List List
1 Bar 1 0 0 35 2 0 0 35 25 10 13
Design Zones
Load Combinations : Construction
Layer Steel Left End Distance to Bar stagger Bottom Right End Distance to Bar stagger Bottom Maximum Minimum Preferred
Load Description 1. Self 2. Extra 3. Live Number type Reference left end of length at left Cover at left Reference right end of length at right Cover at Bar Size Bar Size bar size
Combination Weight Dead Load Load Column bar end end Column bar end Right End
A #.# #.# #.# List # mm mm mm # mm mm mm List List List
1 Construction 1 0 0 1 Bar 1 0 0 35 2 0 0 35 25 10 13
kN/m1 2
-100
10
8
6 -200
4 P1
2
0
0 3000mm -300
Col No. 1 Characteristic Characteristic Service Service Ultimate Ultimate Ultimate Ultimate 1 2
Service Service (Reversal) Flexure Flexure Shear Shear kN
(Reversal) (Reversal) (Reversal) 40 27.7
#.# 30
Elastic Rotation 1.53e-4 1.53e-4 1.3e-4 1.3e-4 2.14e-4 2.14e-4 1.51e-4 2.14e-4
20
Elastic Axial Shortening mm 0 0 0 0 0 0 0 0
10
0
Col No. 2 Characteristic Characteristic Service Service Ultimate Ultimate Ultimate Ultimate -10
Service Service (Reversal) Flexure Flexure Shear Shear -20
(Reversal) (Reversal) (Reversal) -30
Moment Above kNm 0 0 0 0 0 0 0 0 -40 -27.7
Moment Below kNm 0 0 0 0 0 0 0 0 0 3000mm
Reaction kN 24.38 24.38 20.63 20.63 34.03 34.03 24.05 34.03
Elastic Rotation #.# -1.53e-4 -1.53e-4 -1.3e-4 -1.3e-4 -2.14e-4 -2.14e-4 -1.51e-4 -2.14e-4 Shear Shear 1 Shear 2
Elastic Axial Shortening mm 0 0 0 0 0 0 0 0
Flexural Design
Ultimate
Ultimate Design
Flexure 1 2
mm2
2000 0
kNm1 2
100
-4 0
0 3.29 3.29 -100
4 -200
8 -300
12 -400
16 -500
20 -600 543
24 0 3000mm
28 25.5
0 3000mm Reinforcement Top Total Bottom Total Top Ultimate Bottom Ultimate Min Top Min Bot
0.056
12 -0.063
16 0 3000mm
20
24 21.3 Neutral Axis Depth Initial Final
28
0 3000mm
Gross Stress Top Gross Stress Bottom Cracked Compression Reinforcement Tension Gross Stress Top Gross Stress Bottom Cracked Compression Reinforcement Tension
Gross Stress Top Gross Stress Bottom Cracked Compression Reinforcement Tension Gross Stress Top Gross Stress Bottom Cracked Compression Reinforcement Tension
0 0 0 0 0 No shear steel
0 0 0 0 0 No shear steel
0 0 0 0 0 No shear steel
0 0 0 0 0 No shear steel
0 0 0 0 0 No shear steel
RAPT 6.6.8.0 Project Name: J110 Page 11/13 RAPT 6.6.8.0 Project Name: J110 Page 12/13
Licensee: AECOM Singapore Pte Ltd 1/6/2022 6:55:55 PM License No.: 10479063400712WPN11 Licensee: AECOM Singapore Pte Ltd 1/6/2022 6:55:58 PM License No.: 10479063400712WPN11
Frame Description: STAIRCASE SLAB Frame Description: STAIRCASE SLAB
Incremental
Spacing of Sets Minimum Legs Shear Comments
2 legs 4 legs 6 legs Min legs mm1 2
H10 H10 H10 H10 0
mm mm mm mm # A
0 0 0 0 0 No shear steel -0.5
0 0 0 0 0 No shear steel -0.584
0 0 0 0 0 No shear steel -1
0 0 0 0 0 No shear steel
0 0 0 0 0 No shear steel -1.5
0 0 0 0 0 No shear steel
0 0 0 0 0 No shear steel -2 5133
0 0 0 0 0 No shear steel 0 3000mm
0 0 0 0 0 No shear steel
0 0 0 0 0 No shear steel Total Long Term
0 0 0 0 0 No shear steel
0 0 0 0 0 No shear steel mm1 2
0
-0.5
-0.711
-1
Punching
Column Head Critical Section -1.5
Column Bh a at u d fcv P/A Asw/s min V* Mv* V*eff VRd1 VRd2 Asv result
No. -2 4218
A #.# mm mm mm mm MPa MPa mm2/mm kN kNm kN kN kN mm2 A 0 3000mm
1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Check Not Carried Out!
2 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Check Not Carried Out!
Detailed Reinforcement
Span 1
Top Reinforcement Bottom Reinforcement
Design Comments:-
- Span - 1 - Reinforcement added at left span contraflexure point for Offset of Bending Moment Diagram for Shear - 97.78mm2
- Span - 1 - Reinforcement added at right span contraflexure point for Offset of Bending Moment Diagram for Shear - 97.78mm2
Reinforcement Layout
1 2
mm
0
-100
-200
-300
5-H13
0 3000mm
RAPT 6.6.8.0 Project Name: J110 Page 2/21
Licensee: AECOM Singapore Pte Ltd 1/6/2022 6:57:28 PM License No.: 10479063400712WPN11
Project Name: J110
Designer: SLT Column Column Support Transverse Transverse
C:\Users\sujeevanleonard.tham\OneDrive - AECOM\Projects\J110\J110\OneDrive_2021-07-01\12. Southern Grid Type Column prestress
Staircase\Design Files\Str\Slabs\Ground Slab@11.5 (G7BA.1-1).rpf Reference spacing (P/A)
A List mm MPa
5 5 Knife-Edge 1000
RAPT - Version: 6.6.8.0
Reinforced And Post-Tensioned Concrete Analysis & Design Package
Copyright(C) 1988 - 2021 PCDC Pty. Ltd. All Rights Reserved
Load Cases
Load Load Type Load Definition Live Load Description
Licensee Case Deflection Case
AECOM Singapore Pte Ltd
300 Beach Road List List Y/N A
#03-00 The Concourse 1 Self Weight Applied Loads
Singapore 199555 2 Extra Dead Load Applied Loads
10479063400712WPN11 3 Live Load Applied Loads Y
Include Strain Hardening of Reinforcement Y/N N Nominal Bar Bar Area Bar Bar Stock
Beam Shear Critical Section Location List Code Critical Section Bar Size Diameter Inertia Weight Length
A mm mm2 mm4 kg/m mm
20 20 314.2 7857.14 2.47 12000
22 22 380.1 11503.6 2.98 12000
Maximum Service Stress Change - Prestressed Sections MPa 200
25 25 490.9 19182.5 3.85 12000
Maximum Service Stress Change - Reinforced Sections MPa 200
32 32 804.2 51492.6 6.31 12000
Relative Humidity % 80
40 40 1256.6 1.257e5 9.86 12000
Average Temperature C. 30
Prestress Losses Calculations based on List Program Default
Crack Width Calculations List .20 mm Elevation view
AS3600 Shrinkage and Temperature Reinforcement List Moderate
1 2 3 4 5
Degree of Restraint in Primary Direction % 0 mm
Degree of Restraint in Secondary Direction % 0 0
Concrete Strength Gain Rate List N
-50
Concrete Tensile Strength for Deflection Calculations- #.## x (Fc)n #.# -1
Maximum Value of Ieff/Igross for Deflection Calculations #.# 0.6 -100
Total Deflection Warning Limit - Maximum Span/Deflection #.# 250
-150
Total Deflection Warning Limit - Maximum Deflection mm 25
Incremental Deflection Warning Limit - Maximum Span/Deflection #.# 500 -200
Incremental Deflection Warning Limit - Maximum Deflection mm 25
0 4500 7300 10100 13800mm
Initial Time for Shrinkage List Full Shrinkage
Time of Loading in days #.# 10 Plan view
Age Adjustment Factor #.# 0.76
Concrete Strength at Time of Loading MPa 27.04 1 2 3 4 5
Loaded Period in years #.# 30 mm
Tension stiffening Approach List Modified Concrete Tensile Modulus Method -400
#.# -200
Live Load Pattern Factor 1
Pattern Live Load for Ultimate Strength Y/N Y 0
Pattern Live Load for Crack Control Y/N Y
Pattern Live Load For Deflections Y/N Y 200
Pattern Live Load for Deflection Permanent Load Combination Y/N N
400
Material Properties 0 4500 7300 10100 13800mm
Concrete : Standard Concrete : Concrete Strength Basis - Cube Warnings
Description A C32/40MPa Input
Characteristic Compressive Strength MPa 40 No errors or warnings were found.
Mean Compressive Strength MPa 50
Lower Characteristic Tensile Strength MPa 2.12 Output
Upper Characteristic Tensile Strength MPa 3.93 Warning:Flat slabs - slabs which rely on flexural action through the slab or slab thickenings such as drop panels or band beams to discrete column
Concrete Density kg/m3 2447 supports, require concentration of the top reinforcement and tendons over supports within a defined width from the column face to facilitate moment
Design Concrete Modulus MPa 31186.6 transfer to the column. This width varies and the amount of reinforcement varies for different design codes. In the major codes, the requirements are
Mean Concrete Modulus MPa 33345.8 specified in AS3600 cl 9.1.2, Eurocode 1992 - 1 - 1 2004 cl 9.4.1, ACI318-14 cl 8.4.2.3 and BS8110 cl3.7.3.1. For example AS3600 requires that 25% of
Basic Shrinkage Strain mm/mm 0 total negative moment for the entire slab panel be resisted by reinforcement within a width D either side of the column. RAPT cannot define this
#.# concentration as it does not know the transverse spacing of the tendons. It is the designer's responsibility to ensure that these clauses are complied with.
Shrinkage Multiplier 1
Basic Creep Factor #.# 2.656
Creep Multiplier #.# 1
Concrete Strain at Peak Stress #.# 0.002
Squash Load Factor #.# 0.85 Bending Moments
Concrete Strain Limit #.# 0.004 Load Cases
Strength Gain Rate List Normal
mm
Column Actions
Maximum Aggregate Size 20
Col No. 1 Self Extra Dead Live
Weight Load Load
Moment Above kNm -0 -0 -0
Reinforcement Bar Moment Below kNm -0 -0 -0
Designation Type Yield Elastic Ductility Peak Peak Design Material Material Material Capacity Material Capacity Include as Description Reaction kN 9.13 4.57 9.13
Stress Modulus Strain Stress Strain Factor Factor Reduction Factor Reduction Factor Flexural Elastic Rotation #.# 5.33e-4 2.66e-4 5.33e-4
Limit Flexure Shear - Flexure - Shear Reinforcement for Elastic Axial Shortening mm 0 0 0
Shear
H Deformed 500 2.05e5 N 0.05 540 90 -1 -1 -1 -1 Y
Col No. 2 Self Extra Live Load
Weight Dead
Load
Nominal Bar Bar Area Bar Bar Stock Moment Above kNm -0 -0 -0
Bar Size Diameter Inertia Weight Length Moment Below kNm -0 -0 -0
A mm mm2 mm4 kg/m mm Reaction kN 23.48 11.74 23.48
10 10 78.5 491.07 0.62 12000 Elastic Rotation #.# -2.11e-4 -1.06e-4 -2.11e-4
13 13 132.7 1402.55 1.04 12000 Elastic Axial Shortening mm 0 0 0
16 16 201.1 3218.29 1.58 12000
RAPT 6.6.8.0 Project Name: J110 Page 7/21 RAPT 6.6.8.0 Project Name: J110 Page 8/21
Licensee: AECOM Singapore Pte Ltd 1/6/2022 6:57:47 PM License No.: 10479063400712WPN11 Licensee: AECOM Singapore Pte Ltd 1/6/2022 6:57:51 PM License No.: 10479063400712WPN11
Col No. 3 Self Extra Dead Live
Weight Load Load
Moment Above kNm -0 -0 -0 Ultimate Design
Moment Below kNm -0 -0 -0 Flexure
Reaction kN 8.75 4.38 8.75
Elastic Rotation #.# 0 0 0 1 2 3 4 5
kNm
Elastic Axial Shortening mm 0 0 0 -33.8 -33.8
-40
-30 -24 -24
Col No. 4 Self Extra Dead Live -20
Weight Load Load -8.15 -8.15
-10
Moment Above kNm -0 -0 -0 3.19 2.61
0
Moment Below kNm -0 -0 -0 10
kN 6.11 8.79
Reaction 20.23 10.11 20.23 20
Elastic Rotation #.# 0 0 0 30 20.7
Elastic Axial Shortening mm 0 0 0 40 30.5
0 4500 7300 10100 13800mm
Col No. 5 Self Extra Live Load
Weight Dead Moment Moment 1 Moment 2
Load
Moment Above kNm -0 -0 -0
1 2 3 4 5
Moment Below kNm -0 -0 -0
Reaction kN 7.41 3.71 7.41 kN
33.3 36.3
#.# 4029.9
Elastic Rotation -2.86e-4 -1.43e-4 -2.86e-4 19.2
Elastic Axial Shortening mm 0 0 0 20
0
-20
Load Combinations -17.3
-29.4 -24.2
-40
Column Actions -44.3
Col No. 1 Characteristic Characteristic Service Service Ultimate Ultimate Ultimate Ultimate -60
Service Service (Reversal) Flexure Flexure Shear Shear 0 4500 7300 10100 13800mm
(Reversal) (Reversal) (Reversal)
Moment Above kNm 0 0 0 0 0 0 0 0 Shear Shear 1 Shear 2
Moment Below kNm 0 0 0 0 0 0 0 0
Reaction kN 22.83 22.83 18.27 18.27 32.2 32.2 13.13 32.77 Shear
Elastic Rotation #.# 1.33e-3 1.33e-3 1.07e-3 1.07e-3 1.88e-3 1.88e-3 7.12e-4 1.96e-3
Elastic Axial Shortening mm 0 0 0 0 0 0 0 0 1 2 3 4 5
kNm
-40 -34.1 -34.2
Col No. 2 Characteristic Characteristic Service Service Ultimate Ultimate Ultimate Ultimate -24.7 -24.7
Service Service (Reversal) Flexure Flexure Shear Shear -30
(Reversal) (Reversal) (Reversal) -20 -8.15 -8.15
Moment Above kNm 0 0 0 0 0 0 0 0 -10
3.19 2.61
Moment Below kNm 0 0 0 0 0 0 0 0 0
Reaction kN 58.69 58.69 46.95 46.95 82.75 82.75 34.66 83.3 10 1.92 3.94
Elastic Rotation #.# -5.28e-4 -5.28e-4 -4.23e-4 -4.23e-4 -7.45e-4 -7.45e-4 -3.32e-4 -7.3e-4 20 14.4
30 21.2
Elastic Axial Shortening mm 0 0 0 0 0 0 0 0
40
0 4500 7300 10100 13800mm
Col No. 3 Characteristic Characteristic Service Service Ultimate Ultimate Ultimate Ultimate
Service Service (Reversal) Flexure Flexure Shear Shear Moment Moment 1 Moment 2
(Reversal) (Reversal) (Reversal)
Moment Above kNm 0 0 0 0 0 0 0 0
Moment Below kNm 0 0 0 0 0 0 0 0 1 2 3 4 5
Reaction kN 21.88 21.88 17.5 17.5 30.85 30.85 18.28 42.19 kN
34.2 36.5
Elastic Rotation #.# 0 0 0 0 1.01e-4 1.01e-4 2.87e-4 0 4029.9
Elastic Axial Shortening mm 0 0 0 0 0 0 0 0 19.2
20
Col No. 4 Characteristic Characteristic Service Service Ultimate Ultimate Ultimate Ultimate 0
Service Service (Reversal) Flexure Flexure Shear Shear -20
(Reversal) (Reversal) (Reversal) -17.3
-40 -24.2
Moment Above kNm 0 0 0 0 0 0 0 0 -30.8
Moment Below kNm 0 0 0 0 0 0 0 0 -60 -44.4
Reaction kN 50.57 50.57 40.46 40.46 71.3 71.3 30.32 71.33 0 4500 7300 10100 13800mm
Elastic Rotation #.# 2.43e-4 2.43e-4 1.94e-4 1.94e-4 3.42e-4 3.42e-4 1.46e-4 3.42e-4
Elastic Axial Shortening mm 0 0 0 0 0 0 0 0 Shear Shear 1 Shear 2
Col No. 5 Characteristic Characteristic Service Service Ultimate Ultimate Ultimate Ultimate
Service Service (Reversal) Flexure Flexure Shear Shear
(Reversal) (Reversal) (Reversal)
Moment Above kNm 0 0 0 0 0 0 0 0
Moment Below kNm 0 0 0 0 0 0 0 0
Reaction kN 18.53 18.53 14.82 14.82 26.12 26.12 10.26 26.98
Elastic Rotation #.# -7.15e-4 -7.15e-4 -5.72e-4 -5.72e-4 -1.01e-3 -1.01e-3 -3.41e-4 -1.1e-3
Elastic Axial Shortening mm 0 0 0 0 0 0 0 0
RAPT 6.6.8.0 Project Name: J110 Page 9/21 RAPT 6.6.8.0 Project Name: J110 Page 10/21
Licensee: AECOM Singapore Pte Ltd 1/6/2022 6:57:56 PM License No.: 10479063400712WPN11 Licensee: AECOM Singapore Pte Ltd 1/6/2022 6:58:00 PM License No.: 10479063400712WPN11
Flexural Design Service
Ultimate Maximum Moment Condition
1 2 3 4 5 1 2 3 4 5
mm2 MPa MPa
8000 647 347 451 0 -4 -2.8 -2.8 -2.01 -2.01 -200
600 -2 -100
400
0 0
200
0 2 100
-200 4 200
-400 6 300
-600 8 400
-800 575 347 347 378 2.85 2.85 2.03 2.03
0 4500 7300 10100 13800mm 0 4500 7300 10100 13800mm
Reinforcement Top Total Bottom Total Top Ultimate Bottom Ultimate Min Top Min Bot Gross Stress Top Gross Stress Bottom Cracked Compression Reinforcement Tension Limits
0.16
0.083
0.083
Design Comments:-
0.066
0.066
0.12 - Increase in stress from decompression to working exceeds 200MPa in at least one steel layer. Reinforcement has been added to reduce stress change
0.08 below this maximum value. Refer RAPT manual Section T.7.6
0.04
0 Span 2
-0.04 Design Comments:-
-0.08 - Increase in stress from decompression to working exceeds 200MPa in at least one steel layer. Reinforcement has been added to reduce stress change
0.066
0.066
0.07
-0.12 below this maximum value. Refer RAPT manual Section T.7.6
0.106
0 0 0 0 0 No shear steel
0 0 0 0 0 No shear steel
0 0 0 0 0 No shear steel
0 0 0 0 0 No shear steel
0 0 0 0 0 No shear steel Punching
0 0 0 0 0 No shear steel Column Head Critical Section
0 0 0 0 0 No shear steel Column Bh a at u d fcv P/A Asw/s min V* Mv* V*eff VRd1 VRd2 Asv result
0 0 0 0 0 No shear steel No.
0 0 0 0 0 No shear steel A #.# mm mm mm mm MPa MPa mm2/mm kN kNm kN kN kN mm2 A
0 0 0 0 0 No shear steel 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Check Not Carried Out!
0 0 0 0 0 No shear steel 2 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Check Not Carried Out!
0 0 0 0 0 No shear steel 3 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Check Not Carried Out!
0 0 0 0 0 No shear steel 4 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Check Not Carried Out!
0 0 0 0 0 No shear steel 5 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Check Not Carried Out!
0 0 0 0 0 No shear steel
0 0 0 0 0 No shear steel
0 0 0 0 0 No shear steel
RAPT 6.6.8.0 Project Name: J110 Page 15/21 RAPT 6.6.8.0 Project Name: J110 Page 16/21
Licensee: AECOM Singapore Pte Ltd 1/6/2022 6:58:19 PM License No.: 10479063400712WPN11 Licensee: AECOM Singapore Pte Ltd 1/6/2022 6:58:23 PM License No.: 10479063400712WPN11
Deflections Even Spans Loaded
All Spans Loaded Transfer
Transfer
1 2 3 4 5
1 2 3 4 5 mm
mm 0
0.116 -0.033 -0.499
0 -1.14
0.116 -0.033 -0.499 -5
-1.14
-5
-10
-10
-15
-15
-20 3955 24051 84208 7408
-20 3955 24051 84208 7408 0 4500 7300 10100 13800mm
0 4500 7300 10100 13800mm
Short Term
Short Term
1 2 3 4 5
1 2 3 4 5 mm
mm 0
0.104 0.121
0 -1.55 -1.01
0.245 -0.063 -5
-0.95
-5 -3.42
-10
-10
-15
-15
-20 2905 26855 23205 3656
-20 1315 11443 44222 3893 0 4500 7300 10100 13800mm
0 4500 7300 10100 13800mm
All Spans Loaded Odd Spans Loaded Even Spans Loaded
Even Spans Loaded Odd Spans Loaded All Spans Loaded
Incremental
Incremental
1 2 3 4 5
1 2 3 4 5 mm
mm 0
0.332 0.193
0 -2.03
0.477 0.139 -5 -3.8
-5 -1.97
-5.67 -10
-10
-15
-15
-20 1186 8439 14532 1826
-20 794 5873 20095 1883 0 4500 7300 10100 13800mm
0 4500 7300 10100 13800mm
All Spans Loaded Odd Spans Loaded Even Spans Loaded
Even Spans Loaded Odd Spans Loaded All Spans Loaded
Total Long Term
Total Long Term
1 2 3 4 5
1 2 3 4 5 mm
mm 0
0.443 0.222
0
0.588 0.171 -5 -2.5
-2.44 -4.88
-5
-10
-6.75
-10
-15
-15
-20 923 6327 12638 1479
-20 667 4766 16422 1516 0 4500 7300 10100 13800mm
0 4500 7300 10100 13800mm
All Spans Loaded Odd Spans Loaded Even Spans Loaded
Even Spans Loaded Odd Spans Loaded All Spans Loaded
RAPT 6.6.8.0 Project Name: J110 Page 17/21 RAPT 6.6.8.0 Project Name: J110 Page 18/21
Licensee: AECOM Singapore Pte Ltd 1/6/2022 6:58:27 PM License No.: 10479063400712WPN11 Licensee: AECOM Singapore Pte Ltd 1/6/2022 6:58:31 PM License No.: 10479063400712WPN11
Odd Spans Loaded Top Reinforcement Bottom Reinforcement
Transfer
Max Max Section Max Max Section
1 2 3 4 5 Locat Size Space Area Depth Width Rebar Reqd Size Space Area Depth Width Rebar Reqd
mm mm mm mm mm2 mm mm A mm mm mm2 mm mm A
0 800 0 0 0 41.5 1000 No Steel Added 16 152.9 383.41 158.5 1000 3 H13 @ 346.1
0.116 -0.033 -0.499 960 0 0 0 41.5 1000 No Steel Added 16 152.3 434.69 158.5 1000 4 H13 @ 305.3
-1.14
-5 1125 0 0 0 41.5 1000 No Steel Added 16 152.5 480.16 158.5 1000 4 H13 @ 276.4
1500 0 0 0 41.5 1000 No Steel Added 16 150.4 554.15 158.5 1000 5 H13 @ 239.5
-10 1875 0 0 0 41.5 1000 No Steel Added 16 150.4 574.79 158.5 1000 5 H13 @ 230.9
2250 0 0 0 41.5 1000 No Steel Added 16 150.5 546.68 158.5 1000 5 H13 @ 242.7
-15
2625 0 0 0 41.5 1000 No Steel Added 16 152.5 465.31 158.5 1000 4 H13 @ 285.2
-20 3955 24051 84208 7408 3000 0 0 0 41.5 1000 No Steel Added 16 153.2 346.88 158.5 1000 3 H13 @ 382.6
0 4500 7300 10100 13800mm 3375 0 0 0 41.5 1000 No Steel Added 25 300 346.88 158.5 1000 3 H13 @ 382.6
3540 0 0 346.64 41.5 1000 3 H13 @ 382.8 25 300 346.88 158.5 1000 3 H13 @ 382.6
Short Term 3700 25 300 346.88 41.5 1000 3 H13 @ 382.6 0 0 346.64 158.5 1000 3 H13 @ 382.8
3860 25 300 346.88 41.5 1000 3 H13 @ 382.6 0 0 0 158.5 1000 No Steel Added
1 2 3 4 5 4020 25 220.9 346.88 41.5 1000 3 H13 @ 382.6 0 0 0 158.5 1000 No Steel Added
mm 4180 16 153.2 412.62 41.5 1000 4 H13 @ 321.6 0 0 0 158.5 1000 No Steel Added
0 4340 16 150.4 515.74 41.5 1000 4 H13 @ 257.3 0 0 0 158.5 1000 No Steel Added
0.319 -0.149 -0.651 4499 16 150.2 646.54 41.5 1000 5 H13 @ 205.2 0 0 0 158.5 1000 No Steel Added
-5 -3.76 Shear Reinforcement
Spacing of Sets
-10
2 legs 4 legs 6 legs Min legs Minimum Shear
Area H10 H10 H10 H10 Legs Comments
-15
mm2/mm mm mm mm mm # A
-20 1196 8767 18813 5683
0 4500 7300 10100 13800mm 0 0 0 0 0 0 No shear steel
0 0 0 0 0 0 No shear steel
All Spans Loaded Even Spans Loaded Odd Spans Loaded 0 0 0 0 0 0 No shear steel
0 0 0 0 0 0 No shear steel
Incremental 0 0 0 0 0 0 No shear steel
0 0 0 0 0 0 No shear steel
1 2 3 4 5 0 0 0 0 0 0 No shear steel
mm 0 0 0 0 0 0 No shear steel
0
0.543 -0.187 0 0 0 0 0 0 No shear steel
-1.67 0 0 0 0 0 0 No shear steel
-5
0 0 0 0 0 0 No shear steel
-6.01
-10 0 0 0 0 0 0 No shear steel
0 0 0 0 0 0 No shear steel
-15 0 0 0 0 0 0 No shear steel
0 0 0 0 0 0 No shear steel
-20 749 5156 14964 2221 0 0 0 0 0 0 No shear steel
0 4500 7300 10100 13800mm 0 0 0 0 0 0 No shear steel
0 0 0 0 0 0 No shear steel
All Spans Loaded Even Spans Loaded Odd Spans Loaded
0 0 0 0 0 0 No shear steel
Total Long Term
1 2 3 4 5 Design Comments:-
mm - Span - 1 - Reinforcement added at right support contraflexure point for Offset of Bending Moment Diagram for Shear - 37.71mm2
0 - Span - 1 - Reinforcement added at left span contraflexure point for Offset of Bending Moment Diagram for Shear - 94.16mm2
0.652 -0.219 - Span - 1 - Reinforcement added at right span contraflexure point for Offset of Bending Moment Diagram for Shear - 71.08mm2
-5 -2.14
-7.09 Span 2
-10 Top Reinforcement Bottom Reinforcement
-15
Max Max Section Max Max Section
Locat Size Space Area Depth Width Rebar Reqd Size Space Area Depth Width Rebar Reqd
-20 635 4295 12798 1728 mm mm mm mm2 mm mm A mm mm mm2 mm mm A
0 4500 7300 10100 13800mm
1 16 150.2 646.76 41.5 1000 5 H13 @ 205.2 0 0 0 158.5 1000 No Steel Added
Detailed Reinforcement
160 16 150.3 538.52 41.5 1000 5 H13 @ 246.4 0 0 0 158.5 1000 No Steel Added
Span 1All Spans Loaded Even Spans Loaded Odd Spans Loaded 268 16 152.4 465.73 41.5 1000 4 H13 @ 284.9 0 0 0 158.5 1000 No Steel Added
Top Reinforcement Bottom Reinforcement
376 16 152.5 424.2 41.5 1000 4 H13 @ 312.8 0 0 0 158.5 1000 No Steel Added
484 16 153.2 384.72 41.5 1000 3 H13 @ 344.9 0 0 0 158.5 1000 No Steel Added
Max Max Section Max Max Section
592 16 169.1 347.84 41.5 1000 3 H13 @ 381.5 0 0 0 158.5 1000 No Steel Added
Locat Size Space Area Depth Width Rebar Reqd Size Space Area Depth Width Rebar Reqd
mm mm mm mm2 mm mm A mm mm mm2 mm mm A 700 16 199.2 346.88 41.5 1000 3 H13 @ 382.6 0 0 0 158.5 1000 No Steel Added
933 25 300 346.88 41.5 1000 3 H13 @ 382.6 0 0 346.64 158.5 1000 5 H10 @ 226.5
100 0 0 0 41.5 1000 No Steel Added 25 300 346.88 158.5 1000 3 H13 @ 382.6
1166 25 300 346.88 41.5 1000 3 H13 @ 382.6 0 0 346.64 158.5 1000 5 H10 @ 226.5
160 0 0 0 41.5 1000 No Steel Added 25 300 346.88 158.5 1000 3 H13 @ 382.6
1400 25 300 346.88 41.5 1000 5 H10 @ 226.3 25 300 346.64 158.5 1000 5 H10 @ 226.5
320 0 0 0 41.5 1000 No Steel Added 25 300 346.88 158.5 1000 3 H13 @ 382.6
1634 25 300 346.64 41.5 1000 5 H10 @ 226.5 25 300 346.88 158.5 1000 5 H10 @ 226.3
480 0 0 0 41.5 1000 No Steel Added 25 216.4 346.88 158.5 1000 3 H13 @ 382.6
1867 25 300 346.64 41.5 1000 5 H10 @ 226.5 25 300 346.88 158.5 1000 5 H10 @ 226.3
640 0 0 0 41.5 1000 No Steel Added 16 167.6 346.88 158.5 1000 3 H13 @ 382.6
2100 0 0 346.64 41.5 1000 5 H10 @ 226.5 25 300 346.88 158.5 1000 5 H10 @ 226.3
RAPT 6.6.8.0 Project Name: J110 Page 19/21 RAPT 6.6.8.0 Project Name: J110 Page 20/21
Licensee: AECOM Singapore Pte Ltd 1/6/2022 6:58:34 PM License No.: 10479063400712WPN11 Licensee: AECOM Singapore Pte Ltd 1/6/2022 6:58:38 PM License No.: 10479063400712WPN11
Top Reinforcement Bottom Reinforcement Shear Reinforcement
Spacing of Sets
Max Max Section Max Max Section 2 legs 4 legs 6 legs Min legs Minimum Shear
Locat Size Space Area Depth Width Rebar Reqd Size Space Area Depth Width Rebar Reqd Area H10 H10 H10 H10 Legs Comments
mm mm mm mm2 mm mm A mm mm mm2 mm mm A mm2/mm mm mm mm mm # A
2200 0 0 346.64 41.5 1000 5 H10 @ 226.5 25 300 346.88 158.5 1000 5 H10 @ 226.3
2300 0 0 346.64 41.5 1000 5 H10 @ 226.5 25 300 346.88 158.5 1000 5 H10 @ 226.3 0 0 0 0 0 0 No shear steel
2400 25 300 346.64 41.5 1000 5 H10 @ 226.5 25 300 346.88 158.5 1000 5 H10 @ 226.3 0 0 0 0 0 0 No shear steel
2520 25 300 346.88 41.5 1000 5 H10 @ 226.3 25 300 346.64 158.5 1000 5 H10 @ 226.5 0 0 0 0 0 0 No shear steel
2640 25 300 346.88 41.5 1000 5 H10 @ 226.3 0 0 346.64 158.5 1000 5 H10 @ 226.5 0 0 0 0 0 0 No shear steel
2799 25 300 346.88 41.5 1000 5 H10 @ 226.3 0 0 346.64 158.5 1000 5 H10 @ 226.5 0 0 0 0 0 0 No shear steel
Shear Reinforcement 0 0 0 0 0 0 No shear steel
Spacing of Sets 0 0 0 0 0 0 No shear steel
2 legs 4 legs 6 legs Min legs Minimum Shear 0 0 0 0 0 0 No shear steel
Area H10 H10 H10 H10 Legs Comments 0 0 0 0 0 0 No shear steel
mm2/mm mm mm mm mm # A 0 0 0 0 0 0 No shear steel
0 0 0 0 0 0 No shear steel
0 0 0 0 0 0 No shear steel 0 0 0 0 0 0 No shear steel
0 0 0 0 0 0 No shear steel 0 0 0 0 0 0 No shear steel
0 0 0 0 0 0 No shear steel 0 0 0 0 0 0 No shear steel
0 0 0 0 0 0 No shear steel 0 0 0 0 0 0 No shear steel
0 0 0 0 0 0 No shear steel 0 0 0 0 0 0 No shear steel
0 0 0 0 0 0 No shear steel 0 0 0 0 0 0 No shear steel
0 0 0 0 0 0 No shear steel
0 0 0 0 0 0 No shear steel
0 0 0 0 0 0 No shear steel Design Comments:-
0 0 0 0 0 0 No shear steel - - Column Grid 3 - Required Bar Size is smaller than the Preferred Bar Size. Maintaining the same cover will require slightly less reinforcement than
0 0 0 0 0 0 No shear steel calculated.
0 0 0 0 0 0 No shear steel - - Span 3 - Required Bar Size is smaller than the Preferred Bar Size. Maintaining the same cover will require slightly less reinforcement than calculated.
0 0 0 0 0 0 No shear steel - Span - 3 - Reinforcement added at left span contraflexure point for Offset of Bending Moment Diagram for Shear - 47.8mm2
0 0 0 0 0 0 No shear steel - Span - 3 - Reinforcement added at right span contraflexure point for Offset of Bending Moment Diagram for Shear - 44.63mm2
0 0 0 0 0 0 No shear steel
0 0 0 0 0 0 No shear steel Span 4
0 0 0 0 0 0 No shear steel Top Reinforcement Bottom Reinforcement
Design Comments:-
- - Span 4 - Required Bar Size is smaller than the Preferred Bar Size. Maintaining the same cover will require slightly less reinforcement than calculated.
- Span - 4 - Reinforcement added at left support contraflexure point for Offset of Bending Moment Diagram for Shear - 29.4mm2
- Span - 4 - Reinforcement added at left span contraflexure point for Offset of Bending Moment Diagram for Shear - 66.34mm2
- Span - 4 - Reinforcement added at right span contraflexure point for Offset of Bending Moment Diagram for Shear - 77.53mm2
Reinforcement Layout
1 2 3 4 5
mm
5-H10
5-H13
4-H13
0
-50
-100
-150
5-H13
5-H10
5-H10
5-H10
-200
0 4500 7300 10100 13800mm
- - Column Grid 3 - Required Bar Size is smaller than the Preferred Bar Size. Maintaining the same cover will require slightly less reinforcement than
calculated.
- - Span 2 - Required Bar Size is smaller than the Preferred Bar Size. Maintaining the same cover will require slightly less reinforcement than calculated.
- Span - 2 - Reinforcement added at left span contraflexure point for Offset of Bending Moment Diagram for Shear - 37.96mm2
- Span - 2 - Reinforcement added at right span contraflexure point for Offset of Bending Moment Diagram for Shear - 4.68mm2
- - Column Grid 3 - Required Bar Size is smaller than the Preferred Bar Size. Maintaining the same cover will require slightly less reinforcement than
calculated.
- - Span 3 - Required Bar Size is smaller than the Preferred Bar Size. Maintaining the same cover will require slightly less reinforcement than calculated.
- Span - 3 - Reinforcement added at left span contraflexure point for Offset of Bending Moment Diagram for Shear - 47.8mm2
- Span - 3 - Reinforcement added at right span contraflexure point for Offset of Bending Moment Diagram for Shear - 44.63mm2
- - Span 4 - Required Bar Size is smaller than the Preferred Bar Size. Maintaining the same cover will require slightly less reinforcement than calculated.
- Span - 4 - Reinforcement added at left span contraflexure point for Offset of Bending Moment Diagram for Shear - 66.34mm2
- Span - 4 - Reinforcement added at right span contraflexure point for Offset of Bending Moment Diagram for Shear - 77.53mm2
RAPT 6.6.8.0 Project Name: J110 Page 2/30
Licensee: 1/6/2022 7:05:42 PM License No.: 10479063400712WPN11
Project Name: J110
Designer: SLT Column Column Support Transverse Transverse
C:\Users\sujeevanleonard.tham\OneDrive - AECOM\Projects\J110\J110\OneDrive_2021-07-01\12. Southern Grid Type Column prestress
Staircase\Design Files\Str\Slabs\Ground Slab@11.5 (G8B3-4).rpf Reference spacing (P/A)
A List mm MPa
2 2 Knife-Edge 1000
RAPT - Version: 6.6.8.0
3 3 Knife-Edge 1000
Reinforced And Post-Tensioned Concrete Analysis & Design Package 4 4 Knife-Edge 1000
Copyright(C) 1988 - 2021 PCDC Pty. Ltd. All Rights Reserved 5 5 Knife-Edge 1000
6 6 Knife-Edge 1000
Licensee 7 7 Knife-Edge 1000
AECOM Singapore Pte Ltd 8 8 Knife-Edge 1000
300 Beach Road
#03-00 The Concourse
Singapore 199555 Load Cases
10479063400712WPN11 Load Load Type Load Definition Live Load Description
Case Deflection Case
kN/m 1 2 3 4 5 6 7 8 1 2 3 4
mm
6 0
4
P1
2 -50
0
900 3600 6400 9900 12200 15500 18300 21100 mm -100
1 2 3 4 5 6 7 8 -200
kN/m
6 P1 900 3600 6400 9900
4
2
0
900 3600 6400 9900 12200 15500 18300 21100 mm
Reinforcement
Reinforcement Reinforcement Preferred Number
Use Type Bar Size of Legs
List List #
Flexural Bar H 500MPa
Flexural Mesh A 500MPa
Shear Option 1 H 500MPa 10 2
RAPT 6.6.8.0 Project Name: J110 Page 5/30 RAPT 6.6.8.0 Project Name: J110 Page 6/30
Licensee: AECOM Singapore Pte Ltd 1/6/2022 7:05:54 PM License No.: 10479063400712WPN11 Licensee: AECOM Singapore Pte Ltd 1/6/2022 7:05:58 PM License No.: 10479063400712WPN11
Concrete Tensile Strength for Deflection Calculations- #.## x (Fc)n #.# -1 -150
Maximum Value of Ieff/Igross for Deflection Calculations #.# 0.6
-200
Total Deflection Warning Limit - Maximum Span/Deflection #.# 250
Total Deflection Warning Limit - Maximum Deflection mm 25 900 3600 6400 9900 12200 15500 18300 21100 mm
Incremental Deflection Warning Limit - Maximum Span/Deflection #.# 500
mm
Plan view
Incremental Deflection Warning Limit - Maximum Deflection 25
Initial Time for Shrinkage List Full Shrinkage 1 2 3 4 5 6 7 8
Time of Loading in days #.# 10 mm
Age Adjustment Factor #.# 0.76 -400
Concrete Strength at Time of Loading MPa 27.04
Loaded Period in years #.# 30 -200
Tension stiffening Approach List Modified Concrete Tensile Modulus Method
0
Live Load Pattern Factor #.# 1 200
Pattern Live Load for Ultimate Strength Y/N Y
Pattern Live Load for Crack Control Y/N Y 400
Pattern Live Load For Deflections Y/N Y 900 3600 6400 9900 12200 15500 18300 21100 mm
Pattern Live Load for Deflection Permanent Load Combination Y/N N
Warnings
Input
Material Properties No errors or warnings were found.
Concrete : Standard Concrete : Concrete Strength Basis - Cube
Description A C32/40MPa
RAPT 6.6.8.0 Project Name: J110 Page 7/30 RAPT 6.6.8.0 Project Name: J110 Page 8/30
Licensee: AECOM Singapore Pte Ltd 1/6/2022 7:06:02 PM License No.: 10479063400712WPN11 Licensee: AECOM Singapore Pte Ltd 1/6/2022 7:06:06 PM License No.: 10479063400712WPN11
Output Col No. 8 Self Extra Dead Live Load
Warning:Flat slabs - slabs which rely on flexural action through the slab or slab thickenings such as drop panels or band beams to discrete column Weight Load
supports, require concentration of the top reinforcement and tendons over supports within a defined width from the column face to facilitate moment Moment Above kNm -0 -0 -0
transfer to the column. This width varies and the amount of reinforcement varies for different design codes. In the major codes, the requirements are Moment Below kNm -0 -0 -0
specified in AS3600 cl 9.1.2, Eurocode 1992 - 1 - 1 2004 cl 9.4.1, ACI318-14 cl 8.4.2.3 and BS8110 cl3.7.3.1. For example AS3600 requires that 25% of Reaction kN 5.62 2.81 5.62
total negative moment for the entire slab panel be resisted by reinforcement within a width D either side of the column. RAPT cannot define this Elastic Rotation #.# -1.25e-4 0 -1.25e-4
concentration as it does not know the transverse spacing of the tendons. It is the designer's responsibility to ensure that these clauses are complied with. Elastic Axial Shortening mm 0 0 0
Load Combinations
Bending Moments Column Actions
Load Cases Col No. 1 Characteristic Characteristic Service Service Ultimate Ultimate Ultimate Ultimate
Column Actions Service Service (Reversal) Flexure Flexure Shear Shear
Col No. 1 Self Extra Dead Live (Reversal) (Reversal) (Reversal)
Weight Load Load Moment Above kNm 0 0 0 0 0 0 0 0
Moment Above kNm -0 -0 -0 Moment Below kNm 0 0 0 0 0 0 0 0
Moment Below kNm -0 -0 -0 Reaction kN 27.18 27.18 21.75 21.75 38.33 38.33 15.67 38.99
Reaction kN 10.87 5.44 10.87 Elastic Rotation #.# 1.02e-4 1.02e-4 0 0 1.44e-4 1.44e-4 0 1.8e-4
Elastic Rotation #.# 0 0 0 Elastic Axial Shortening mm 0 0 0 0 0 0 0 0
Elastic Axial Shortening mm 0 0 0
Col No. 2 Characteristic Characteristic Service Service Ultimate Ultimate Ultimate Ultimate
Col No. 2 Self Extra Dead Live Service Service (Reversal) Flexure Flexure Shear Shear
Weight Load Load (Reversal) (Reversal) (Reversal)
Moment Above kNm -0 -0 -0 Moment Above kNm 0 0 0 0 0 0 0 0
Moment Below kNm -0 -0 -0 Moment Below kNm 0 0 0 0 0 0 0 0
Reaction kN 13.54 6.77 13.54 Reaction kN 33.85 33.85 27.08 27.08 47.73 47.73 17.82 52.13
Elastic Rotation #.# 0 0 0 Elastic Rotation #.# 0 0 0 0 0 0 0 0
Elastic Axial Shortening mm 0 0 0 Elastic Axial Shortening mm 0 0 0 0 0 0 0 0
Col No. 3 Self Extra Dead Live Col No. 3 Characteristic Characteristic Service Service Ultimate Ultimate Ultimate Ultimate
Weight Load Load Service Service (Reversal) Flexure Flexure Shear Shear
Moment Above kNm -0 -0 -0 (Reversal) (Reversal) (Reversal)
Moment Below kNm -0 -0 -0 Moment Above kNm 0 0 0 0 0 0 0 0
Reaction kN 16.58 8.29 16.58 Moment Below kNm 0 0 0 0 0 0 0 0
Elastic Rotation #.# 0 0 0 Reaction kN 41.44 41.44 33.15 33.15 58.43 58.43 23.37 60.33
Elastic Axial Shortening mm 0 0 0 Elastic Rotation #.# 1.37e-4 1.37e-4 1.1e-4 1.1e-4 1.93e-4 1.93e-4 1.12e-4 1.72e-4
Elastic Axial Shortening mm 0 0 0 0 0 0 0 0
Col No. 4 Self Extra Dead Live
Weight Load Load Col No. 4 Characteristic Characteristic Service Service Ultimate Ultimate Ultimate Ultimate
Moment Above kNm -0 -0 -0 Service Service (Reversal) Flexure Flexure Shear Shear
Moment Below kNm -0 -0 -0 (Reversal) (Reversal) (Reversal)
Reaction kN 14.48 7.24 14.48 Moment Above kNm 0 0 0 0 0 0 0 0
Elastic Rotation #.# 0 0 0 Moment Below kNm 0 0 0 0 0 0 0 0
Elastic Axial Shortening mm 0 0 0 Reaction kN 36.19 36.19 28.95 28.95 51.03 51.03 19.26 54.84
Elastic Rotation #.# -1.92e-4 -1.92e-4 -1.53e-4 -1.53e-4 -2.7e-4 -2.7e-4 -1.54e-4 -2.49e-4
Col No. 5 Self Extra Dead Live Elastic Axial Shortening mm 0 0 0 0 0 0 0 0
Weight Load Load
Moment Above kNm -0 -0 -0 Col No. 5 Characteristic Characteristic Service Service Ultimate Ultimate Ultimate Ultimate
Moment Below kNm -0 -0 -0 Service Service (Reversal) Flexure Flexure Shear Shear
Reaction kN 13.55 6.78 13.55 (Reversal) (Reversal) (Reversal)
#.# Moment Above kNm 0 0 0 0 0 0 0 0
Elastic Rotation 0 0 0
mm Moment Below kNm 0 0 0 0 0 0 0 0
Elastic Axial Shortening 0 0 0
Reaction kN 33.88 33.88 27.1 27.1 47.77 47.77 17.39 51.94
Elastic Rotation #.# 1.71e-4 1.71e-4 1.36e-4 1.36e-4 2.41e-4 2.41e-4 1.47e-4 2.12e-4
Col No. 6 Self Extra Dead Live
Weight Load Load Elastic Axial Shortening mm 0 0 0 0 0 0 0 0
Moment Above kNm -0 -0 -0
Moment Below kNm -0 -0 -0 Col No. 6 Characteristic Characteristic Service Service Ultimate Ultimate Ultimate Ultimate
Reaction kN 15.58 7.79 15.58 Service Service (Reversal) Flexure Flexure Shear Shear
Elastic Rotation #.# 0 0 0 (Reversal) (Reversal) (Reversal)
Moment Above kNm 0 0 0 0 0 0 0 0
Elastic Axial Shortening mm 0 0 0
Moment Below kNm 0 0 0 0 0 0 0 0
Reaction kN 38.95 38.95 31.16 31.16 54.92 54.92 23.08 57.44
Col No. 7 Self Extra Dead Live
Elastic Rotation #.# -1.23e-4 -1.23e-4 0 0 -1.73e-4 -1.73e-4 0 -1.39e-4
Weight Load Load
Moment Above kNm -0 -0 -0 Elastic Axial Shortening mm 0 0 0 0 0 0 0 0
Moment Below kNm -0 -0 -0
Reaction kN 15.28 7.64 15.28 Col No. 7 Characteristic Characteristic Service Service Ultimate Ultimate Ultimate Ultimate
Elastic Rotation #.# 0 0 0 Service Service (Reversal) Flexure Flexure Shear Shear
mm (Reversal) (Reversal) (Reversal)
Elastic Axial Shortening 0 0 0
Moment Above kNm 0 0 0 0 0 0 0 0
Moment Below kNm 0 0 0 0 0 0 0 0
Reaction kN 38.21 38.21 30.57 30.57 53.88 53.88 20.83 56.15
Elastic Rotation #.# 1.09e-4 1.09e-4 0 0 1.53e-4 1.53e-4 1.06e-4 1.08e-4
RAPT 6.6.8.0 Project Name: J110 Page 9/30 RAPT 6.6.8.0 Project Name: J110 Page 10/30
Licensee: AECOM Singapore Pte Ltd 1/6/2022 7:06:10 PM License No.: 10479063400712WPN11 Licensee: AECOM Singapore Pte Ltd 1/6/2022 7:06:14 PM License No.: 10479063400712WPN11
Col No. 7 Characteristic Characteristic Service Service Ultimate Ultimate Ultimate Ultimate 1 2 3 4 5 6 7 8
kN
Service Service (Reversal) Flexure Flexure Shear Shear 40
(Reversal) (Reversal) (Reversal) 29.9 27.1 27.2
30 20.8 22.6 21.5 24.2
Elastic Axial Shortening mm 0 0 0 0 0 0 0 0
20
10
Col No. 8 Characteristic Characteristic Service Service Ultimate Ultimate Ultimate Ultimate 0
Service Service (Reversal) Flexure Flexure Shear Shear -10
(Reversal) (Reversal) (Reversal) -20 -13
Moment Above kNm 0 0 0 0 0 0 0 0 -20.3 -18.1
-30 -24.2 -25.8 -23.7
Moment Below kNm 0 0 0 0 0 0 0 0 -28.7 -28.3
-40
Reaction kN 14.05 14.05 11.24 11.24 19.81 19.81 7.33 20.91 900 3600 6400 9900 12200 15500 18300 21100 mm
Elastic Rotation #.# -3.11e-4 -3.11e-4 -2.49e-4 -2.49e-4 -4.39e-4 -4.39e-4 -1.22e-4 -5.04e-4
Elastic Axial Shortening mm 0 0 0 0 0 0 0 0 Shear Shear 1 Shear 2
Flexural Design
Ultimate Design Ultimate
Flexure
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8 mm2
400 347 347 347 347 347 347 347 0
kNm
-20 -17.4 -17.4 -15.7 -15.7 300
-15.2 -15.2 -13.5 -13.5 -14.7 -14.7
-15 -12.7 -12.7 200
100
-10 -7.12 -7.12
0
-5 -100
0 2
-200
5 -300
3.44
10 7.03 6.45 -400
9.83 0 347 347 347 347 347 347 347
15 12.5 12.4
13.7 900 3600 6400 9900 12200 15500 18300 21100 mm
900 3600 6400 9900 12200 15500 18300 21100 mm
Reinforcement Top Total Bottom Total Top Ultimate Bottom Ultimate Min Top Min Bot
Moment Moment 1 Moment 2
kNm 1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8 -32
kN
-24
40 29.4 26.6 24 27.1 -16
30 22.3 20.9
16.5 -8
20
10 0
0 8
-10 16
-20 -13 24
-19.7 -18.1
-30 -24.2 -25.3 -23.4 32
-28.3 -27.8 900 3600 6400 9900 12200 15500 18300 21100 mm
-40
900 3600 6400 9900 12200 15500 18300 21100 mm
Capacity Minimum Ultimate Design Initial Final
Shear Shear 1 Shear 2
1 2 3 4 5 6 7 8
0.066
0.066
0.066
0.066
0.066
0.066
0.066
0.066
0.066
0.066
0.066
0.066
0.066
0.066
Shear
0.08
0.06
1 2 3 4 5 6 7 8
0.04
kNm
-17.9 -17.9 0.02
-20 -15.6 -15.6 -14.1 -14 -16.1 -16.1 -14.8 -14.8
-12.9 -12.9 0
-15
-0.02
-10 -7.12 -7.11
-0.04
-5
2 -0.06
0
0.066
0.066
0.066
0.066
0.066
0.066
0.066
-0.538 -0.08
5 2.63 2.3
5.15 900 3600 6400 9900 12200 15500 18300 21100 mm
10
9.26 8.4 8.76
15 Neutral Axis Depth Initial Final
900 3600 6400 9900 12200 15500 18300 21100 mm
Span 1
Moment Moment 1 Moment 2 Design Comments:-
- As there is no area of steel in the tension zone (any prestressing tendons are in the compression zone) we are now adding an area of steel, equivalent to
that required for minimum reinforcement, to the design tension layer. This is then assumed to be the initial design reinforcement setup. More reinforcement will
be added as required to achieve the applied moments. Ast added = 307.92mm2 @ 1163mm
RAPT 6.6.8.0 Project Name: J110 Page 11/30 RAPT 6.6.8.0 Project Name: J110 Page 12/30
Licensee: AECOM Singapore Pte Ltd 1/6/2022 7:06:18 PM License No.: 10479063400712WPN11 Licensee: AECOM Singapore Pte Ltd 1/6/2022 7:06:22 PM License No.: 10479063400712WPN11
Span 2 Permanent
Design Comments:- Maximum Moment Condition
- As there is no area of steel in the tension zone (any prestressing tendons are in the compression zone) we are now adding an area of steel, equivalent to
that required for minimum reinforcement, to the design tension layer. This is then assumed to be the initial design reinforcement setup. More reinforcement will 1 2 3 4 5 6 7 8
be added as required to achieve the applied moments. Ast added = 307.92mm2 @ 5000mm MPa MPa
-1.8 -0.54 -0.87 -1.27 -1.27 -1.07 -1.13 -1.13 -1.06 -160
-0.9 -80
Span 3
0 0
Design Comments:-
0.9 80
- As there is no area of steel in the tension zone (any prestressing tendons are in the compression zone) we are now adding an area of steel, equivalent to
1.8 160
that required for minimum reinforcement, to the design tension layer. This is then assumed to be the initial design reinforcement setup. More reinforcement will
be added as required to achieve the applied moments. Ast added = 307.92mm2 @ 6917mm 2.7 240
3.6 320
4.5 400
Span 4 5.4
0.54 0.88 1.29 1.28 1.08 1.14 1.15 1.07
480
Design Comments:- 900 3600 6400 9900 12200 15500 18300 21100 mm
- As there is no area of steel in the tension zone (any prestressing tendons are in the compression zone) we are now adding an area of steel, equivalent to
that required for minimum reinforcement, to the design tension layer. This is then assumed to be the initial design reinforcement setup. More reinforcement will Gross Stress Top Gross Stress Bottom Cracked Compression Reinforcement Tension
be added as required to achieve the applied moments. Ast added = 307.92mm2 @ 11050mm
Reversal Moment Condition
Span 5 1 2 3 4 5 6 7 8
Design Comments:- MPa MPa
- As there is no area of steel in the tension zone (any prestressing tendons are in the compression zone) we are now adding an area of steel, equivalent to -1.8 -0.45 -0.64 -1.02 -1.02 -0.83 -0.91 -0.91 -0.83 -160
that required for minimum reinforcement, to the design tension layer. This is then assumed to be the initial design reinforcement setup. More reinforcement will -0.9 -80
be added as required to achieve the applied moments. Ast added = 307.92mm2 @ 12580mm 0 0
0.9 80
Span 6 1.8 160
Design Comments:- 2.7 240
- As there is no area of steel in the tension zone (any prestressing tendons are in the compression zone) we are now adding an area of steel, equivalent to 3.6 320
that required for minimum reinforcement, to the design tension layer. This is then assumed to be the initial design reinforcement setup. More reinforcement will 4.5 400
be added as required to achieve the applied moments. Ast added = 307.92mm2 @ 16900mm 5.4 0.45 0.65 1.03 1.03 0.84 0.92 0.92 0.84 480
900 3600 6400 9900 12200 15500 18300 21100 mm
Characteristic Service
Span 7 Gross Stress Moment
Maximum Top GrossCondition
Stress Bottom Cracked Compression Reinforcement Tension
Design Comments:-
- As there is no area of steel in the tension zone (any prestressing tendons are in the compression zone) we are now adding an area of steel, equivalent to 1 2 3 4 5 6 7 8
that required for minimum reinforcement, to the design tension layer. This is then assumed to be the initial design reinforcement setup. More reinforcement will MPa MPa
be added as required to achieve the applied moments. Ast added = 307.92mm2 @ 18730mm -3 -0.75 -1.32 -1.82 -1.82 -1.58 -1.64 -1.64 -1.53 -210
-2 -140
-1 -70
0 0
1 70
Service 2 140
3 210
Maximum Moment Condition 4 280
5 350
1 2 3 4 5 6 7 8 6 420
MPa MPa 7 0.75 1.34 1.84 1.84 1.6 1.66 1.66 1.55 490
-2 -0.6 -1 -1.43 -1.43 -1.22 -1.28 -1.28 -1.19 -180 900 3600 6400 9900 12200 15500 18300 21100 mm
-1 -90
0 0 Gross Stress Top Gross Stress Bottom Cracked Compression Reinforcement Tension
1 90
2 180 Reversal Moment Condition
3 270
4 360 1 2 3 4 5 6 7 8
MPa MPa
5 450 -3 -0.45 -0.56 -0.97 -0.97 -0.77 -0.9 -0.9 -0.76 -210
6 0.6 1.01 1.44 1.44 1.23 1.29 1.29 1.21 540 -2 -140
900 3600 6400 9900 12200 15500 18300 21100 mm -1 -70
0 0
Gross Stress Top Gross Stress Bottom Cracked Compression Reinforcement Tension 1 70
2 140
3 210
4 280
5 350
1 2 3 4 5 6 7 8 6 420
MPa MPa 7 0.45 0.56 0.98 0.98 0.77 0.91 0.91 0.77 490
-2 -0.45 -0.61 -1 -1 -0.81 -0.91 -0.91 -0.81 -180 900 3600 6400 9900 12200 15500 18300 21100 mm
-1 -90
0 0 Gross Stress Top Gross Stress Bottom Cracked Compression Reinforcement Tension
1 90
2 180
3 270 Shear Design
4 360 Beam
5 450 Span 0
6 0.45 0.62 1.01 1.01 0.82 0.92 0.92 0.82 540 Locat V* Mv* Pv Mdec d Ast bv phi Vuc phi Vut phi Vu Phi Vumax phi VuMin phi Vus Theta Asv/s
900 3600 6400 9900 12200 15500 18300 21100 mm
Locat V* Mv* Pv Mdec d Ast bv phi Vuc phi Vut phi Vu Phi Vumax phi VuMin phi Vus Theta Asv/s Spacing of Sets Minimum Legs Shear Comments
2 legs 4 legs 6 legs Min legs
H10 H10 H10 H10
mm kN kNm kN kNm mm mm2 mm kN kN kN kN kN kN #.# mm2/mm mm mm mm mm # A
338 -5.96 -1.01 0 0 158.5 346.88 1000 88.76 99999 88.76 796.1 140.35 0 21.8 0 0 0 0 0 0 No shear steel
450 -7.93 -1.78 0 0 158.5 346.88 1000 88.76 99999 88.76 796.1 140.35 0 21.8 0 0 0 0 0 0 No shear steel
563 -9.92 -2.79 0 0 158.5 346.88 1000 88.76 99999 88.76 796.1 140.35 0 21.8 0
675 -11.9 -4.02 0 0 158.5 346.88 1000 88.76 99999 88.76 796.1 140.35 0 21.8 0
740 -13.04 -4.83 0 0 158.5 346.88 1000 88.76 99999 88.76 796.1 140.35 0 21.8 0
899 -15.84 -7.12 0 0 158.5 346.88 1000 0 0 0 796.1 0 0 0 Span 2
Locat V* Mv* Pv Mdec d Ast bv phi Vuc phi Vut phi Vu Phi Vumax phi VuMin phi Vus Theta Asv/s
Spacing of Sets Minimum Legs Shear Comments
2 legs 4 legs 6 legs Min legs
H10 H10 H10 H10 mm kN kNm kN kNm mm mm2 mm kN kN kN kN kN kN #.# mm2/mm
mm mm mm mm # A 1 25.38 -12.87 0 0 158.5 346.88 1000 0 0 0 796.1 0 0 0
0 0 0 0 0 No shear steel 160 22.57 -9.06 0 0 158.5 346.88 1000 88.76 99999 88.76 796.1 140.35 0 21.8 0
0 0 0 0 0 No shear steel 268 20.67 -6.73 0 0 158.5 346.88 1000 88.76 99999 88.76 796.1 140.35 0 21.8 0
0 0 0 0 0 No shear steel 376 18.89 -4.82 0 0 158.5 346.88 1000 88.76 99999 88.76 796.1 140.35 0 21.8 0
0 0 0 0 0 No shear steel 484 16.98 -2.89 0 0 158.5 346.88 1000 88.76 99999 88.76 796.1 140.35 0 21.8 0
0 0 0 0 0 No shear steel 592 15.08 -1.15 0 0 158.5 346.88 1000 88.76 99999 88.76 796.1 140.35 0 21.8 0
0 0 0 0 0 No shear steel 700 13.58 -0.27 0 0 158.5 346.64 1000 88.76 99999 88.76 796.1 140.35 0 21.8 0
0 0 0 0 0 No shear steel 933 9.47 2.42 0 0 158.5 346.88 1000 88.76 99999 88.76 796.1 140.35 0 21.8 0
1166 6.11 3.3 0 0 158.5 346.88 1000 88.76 99999 88.76 796.1 140.35 0 21.8 0
1400 -6.35 2.58 0 0 158.5 346.88 1000 88.76 99999 88.76 796.1 140.35 0 21.8 0
1634 -9.35 1.94 0 0 158.5 346.88 1000 88.76 99999 88.76 796.1 140.35 0 21.8 0
Span 1 1867 -12.69 0.32 0 0 158.5 346.88 1000 88.76 99999 88.76 796.1 140.35 0 21.8 0
Locat V* Mv* Pv Mdec d Ast bv phi Vuc phi Vut phi Vu Phi Vumax phi VuMin phi Vus Theta Asv/s 2100 -16.8 -3.11 0 0 158.5 346.88 1000 88.76 99999 88.76 796.1 140.35 0 21.8 0
2208 -18.28 -4.33 0 0 158.5 346.88 1000 88.76 99999 88.76 796.1 140.35 0 21.8 0
2316 -20.19 -6.41 0 0 158.5 346.88 1000 88.76 99999 88.76 796.1 140.35 0 21.8 0
mm kN kNm kN kNm mm mm2 mm kN kN kN kN kN kN #.# mm2/mm 2424 -22.09 -8.69 0 0 158.5 346.88 1000 88.76 99999 88.76 796.1 140.35 0 21.8 0
1 23.62 -7.11 0 0 158.5 346.88 1000 0 0 0 796.1 0 0 0 2532 -23.87 -10.93 0 0 158.5 346.88 1000 88.76 99999 88.76 796.1 140.35 0 21.8 0
160 20.82 -3.58 0 0 158.5 346.88 1000 88.76 99999 88.76 796.1 140.35 0 21.8 0 2640 -25.77 -13.62 0 0 158.5 346.88 1000 88.76 99999 88.76 796.1 140.35 0 21.8 0
263 19 -1.53 0 0 158.5 346.88 1000 88.76 99999 88.76 796.1 140.35 0 21.8 0 2799 -28.57 -17.94 0 0 158.5 346.88 1000 0 0 0 796.1 0 0 0
366 17.39 -0.02 0 0 158.5 346.88 1000 88.76 99999 88.76 796.1 140.35 0 21.8 0
469 15.57 1.68 0 0 158.5 346.88 1000 88.76 99999 88.76 796.1 140.35 0 21.8 0 Spacing of Sets Minimum Legs Shear Comments
572 13.76 3.19 0 0 158.5 346.88 1000 88.76 99999 88.76 796.1 140.35 0 21.8 0 2 legs 4 legs 6 legs Min legs
675 12.53 3.63 0 0 158.5 346.88 1000 88.76 99999 88.76 796.1 140.35 0 21.8 0 H10 H10 H10 H10
900 8.7 4.79 0 0 158.5 346.88 1000 88.76 99999 88.76 796.1 140.35 0 21.8 0 mm mm mm mm # A
1125 5.58 6.45 0 0 158.5 346.88 1000 88.76 99999 88.76 796.1 140.35 0 21.8 0
1350 -5.05 5.15 0 0 158.5 346.88 1000 88.76 99999 88.76 796.1 140.35 0 21.8 0 0 0 0 0 0 No shear steel
1575 -8.16 4.91 0 0 158.5 346.88 1000 88.76 99999 88.76 796.1 140.35 0 21.8 0 0 0 0 0 0 No shear steel
1800 -11.57 3.63 0 0 158.5 346.88 1000 88.76 99999 88.76 796.1 140.35 0 21.8 0 0 0 0 0 0 No shear steel
2025 -15.54 0.58 0 0 158.5 346.88 1000 88.76 99999 88.76 796.1 140.35 0 21.8 0 0 0 0 0 0 No shear steel
2128 -17.06 -0.49 0 0 158.5 346.64 1000 88.76 99999 88.76 796.1 140.35 0 21.8 0 0 0 0 0 0 No shear steel
2231 -18.87 -2.34 0 0 158.5 346.88 1000 88.76 99999 88.76 796.1 140.35 0 21.8 0 0 0 0 0 0 No shear steel
2334 -20.69 -4.38 0 0 158.5 346.88 1000 88.76 99999 88.76 796.1 140.35 0 21.8 0 0 0 0 0 0 No shear steel
2437 -22.42 -6.39 0 0 158.5 346.88 1000 88.76 99999 88.76 796.1 140.35 0 21.8 0 0 0 0 0 0 No shear steel
2540 -24.23 -8.8 0 0 158.5 346.88 1000 88.76 99999 88.76 796.1 140.35 0 21.8 0 0 0 0 0 0 No shear steel
2699 -27.04 -12.87 0 0 158.5 346.88 1000 0 0 0 796.1 0 0 0 0 0 0 0 0 No shear steel
0 0 0 0 0 No shear steel
Spacing of Sets Minimum Legs Shear Comments 0 0 0 0 0 No shear steel
2 legs 4 legs 6 legs Min legs 0 0 0 0 0 No shear steel
H10 H10 H10 H10 0 0 0 0 0 No shear steel
mm mm mm mm # A 0 0 0 0 0 No shear steel
0 0 0 0 0 No shear steel
0 0 0 0 0 No shear steel 0 0 0 0 0 No shear steel
0 0 0 0 0 No shear steel
0 0 0 0 0 No shear steel
0 0 0 0 0 No shear steel
0 0 0 0 0 No shear steel
Span 3
0 0 0 0 0 No shear steel
Locat V* Mv* Pv Mdec d Ast bv phi Vuc phi Vut phi Vu Phi Vumax phi VuMin phi Vus Theta Asv/s
0 0 0 0 0 No shear steel
0 0 0 0 0 No shear steel
0 0 0 0 0 No shear steel mm kN kNm kN kNm mm mm2 mm kN kN kN kN kN kN #.# mm2/mm
0 0 0 0 0 No shear steel 1 32.72 -17.93 0 0 158.5 346.88 1000 0 0 0 796.1 0 0 0
0 0 0 0 0 No shear steel 160 29.92 -12.95 0 0 158.5 346.88 1000 88.76 99999 88.76 796.1 140.35 0 21.8 0
0 0 0 0 0 No shear steel 279 27.82 -9.52 0 0 158.5 346.88 1000 88.76 99999 88.76 796.1 140.35 0 21.8 0
0 0 0 0 0 No shear steel 398 25.72 -6.33 0 0 158.5 346.88 1000 88.76 99999 88.76 796.1 140.35 0 21.8 0
0 0 0 0 0 No shear steel 517 23.77 -3.7 0 0 158.5 346.88 1000 88.76 99999 88.76 796.1 140.35 0 21.8 0
0 0 0 0 0 No shear steel 636 21.67 -1 0 0 158.5 346.64 1000 88.76 99999 88.76 796.1 140.35 0 21.8 0
RAPT 6.6.8.0 Project Name: J110 Page 15/30 RAPT 6.6.8.0 Project Name: J110 Page 16/30
Licensee: AECOM Singapore Pte Ltd 1/6/2022 7:06:34 PM License No.: 10479063400712WPN11 Licensee: AECOM Singapore Pte Ltd 1/6/2022 7:06:38 PM License No.: 10479063400712WPN11
Locat V* Mv* Pv Mdec d Ast bv phi Vuc phi Vut phi Vu Phi Vumax phi VuMin phi Vus Theta Asv/s Locat V* Mv* Pv Mdec d Ast bv phi Vuc phi Vut phi Vu Phi Vumax phi VuMin phi Vus Theta Asv/s
mm kN kNm kN kNm mm mm2 mm kN kN kN kN kN kN #.# mm2/mm mm kN kNm kN kNm mm mm2 mm kN kN kN kN kN kN #.# mm2/mm
755 19.57 1.45 0 0 158.5 346.88 1000 88.76 99999 88.76 796.1 140.35 0 21.8 0 2140 -20.33 -10.6 0 0 158.5 346.88 1000 88.76 99999 88.76 796.1 140.35 0 21.8 0
875 17.96 2.76 0 0 158.5 346.88 1000 88.76 99999 88.76 796.1 140.35 0 21.8 0 2299 -23.13 -14.05 0 0 158.5 346.88 1000 0 0 0 796.1 0 0 0
1166 12.83 7.24 0 0 158.5 346.88 1000 88.76 99999 88.76 796.1 140.35 0 21.8 0
1457 8.63 9.02 0 0 158.5 346.88 1000 88.76 99999 88.76 796.1 140.35 0 21.8 0 Spacing of Sets Minimum Legs Shear Comments
1750 4.89 9.26 0 0 158.5 346.88 1000 88.76 99999 88.76 796.1 140.35 0 21.8 0 2 legs 4 legs 6 legs Min legs
2043 -7.37 9.66 0 0 158.5 346.88 1000 88.76 99999 88.76 796.1 140.35 0 21.8 0 H10 H10 H10 H10
2334 -11.61 8.22 0 0 158.5 346.88 1000 88.76 99999 88.76 796.1 140.35 0 21.8 0 mm mm mm mm # A
2625 -16.74 4.09 0 0 158.5 346.88 1000 88.76 99999 88.76 796.1 140.35 0 21.8 0
2745 -18.39 2.88 0 0 158.5 346.88 1000 88.76 99999 88.76 796.1 140.35 0 21.8 0 0 0 0 0 0 No shear steel
2864 -20.49 0.57 0 0 158.5 346.88 1000 88.76 99999 88.76 796.1 140.35 0 21.8 0 0 0 0 0 0 No shear steel
2983 -22.58 -1.99 0 0 158.5 346.88 1000 88.76 99999 88.76 796.1 140.35 0 21.8 0 0 0 0 0 0 No shear steel
3102 -24.55 -4.51 0 0 158.5 346.88 1000 88.76 99999 88.76 796.1 140.35 0 21.8 0 0 0 0 0 0 No shear steel
3221 -26.65 -7.55 0 0 158.5 346.88 1000 88.76 99999 88.76 796.1 140.35 0 21.8 0 0 0 0 0 0 No shear steel
3340 -28.75 -10.85 0 0 158.5 346.88 1000 88.76 99999 88.76 796.1 140.35 0 21.8 0 0 0 0 0 0 No shear steel
3499 -31.55 -15.64 0 0 158.5 346.88 1000 0 0 0 796.1 0 0 0 0 0 0 0 0 No shear steel
0 0 0 0 0 No shear steel
Spacing of Sets Minimum Legs Shear Comments 0 0 0 0 0 No shear steel
2 legs 4 legs 6 legs Min legs 0 0 0 0 0 No shear steel
H10 H10 H10 H10 0 0 0 0 0 No shear steel
mm mm mm mm # A 0 0 0 0 0 No shear steel
0 0 0 0 0 No shear steel
0 0 0 0 0 No shear steel 0 0 0 0 0 No shear steel
0 0 0 0 0 No shear steel 0 0 0 0 0 No shear steel
0 0 0 0 0 No shear steel 0 0 0 0 0 No shear steel
0 0 0 0 0 No shear steel 0 0 0 0 0 No shear steel
0 0 0 0 0 No shear steel 0 0 0 0 0 No shear steel
0 0 0 0 0 No shear steel
0 0 0 0 0 No shear steel
0 0 0 0 0 No shear steel
0 0 0 0 0 No shear steel
Span 5
0 0 0 0 0 No shear steel
Locat V* Mv* Pv Mdec d Ast bv phi Vuc phi Vut phi Vu Phi Vumax phi VuMin phi Vus Theta Asv/s
0 0 0 0 0 No shear steel
0 0 0 0 0 No shear steel
0 0 0 0 0 No shear steel mm kN kNm kN kNm mm mm2 mm kN kN kN kN kN kN #.# mm2/mm
0 0 0 0 0 No shear steel 1 29.92 -14.05 0 0 158.5 346.88 1000 0 0 0 796.1 0 0 0
0 0 0 0 0 No shear steel 160 27.12 -9.51 0 0 158.5 346.88 1000 88.76 99999 88.76 796.1 140.35 0 21.8 0
0 0 0 0 0 No shear steel 270 25.18 -6.64 0 0 158.5 346.88 1000 88.76 99999 88.76 796.1 140.35 0 21.8 0
0 0 0 0 0 No shear steel 380 23.24 -3.97 0 0 158.5 346.88 1000 88.76 99999 88.76 796.1 140.35 0 21.8 0
0 0 0 0 0 No shear steel 490 21.43 -1.78 0 0 158.5 346.88 1000 88.76 99999 88.76 796.1 140.35 0 21.8 0
0 0 0 0 0 No shear steel 600 19.49 0.47 0 0 158.5 346.88 1000 88.76 99999 88.76 796.1 140.35 0 21.8 0
710 17.55 2.5 0 0 158.5 346.88 1000 88.76 99999 88.76 796.1 140.35 0 21.8 0
825 15.96 3.62 0 0 158.5 346.88 1000 88.76 99999 88.76 796.1 140.35 0 21.8 0
1100 11.12 7.34 0 0 158.5 346.88 1000 88.76 99999 88.76 796.1 140.35 0 21.8 0
Span 4 1375 7.11 8.66 0 0 158.5 346.88 1000 88.76 99999 88.76 796.1 140.35 0 21.8 0
Locat V* Mv* Pv Mdec d Ast bv phi Vuc phi Vut phi Vu Phi Vumax phi VuMin phi Vus Theta Asv/s 1650 -4.85 8.4 0 0 158.5 346.88 1000 88.76 99999 88.76 796.1 140.35 0 21.8 0
1925 -8.36 8.14 0 0 158.5 346.88 1000 88.76 99999 88.76 796.1 140.35 0 21.8 0
2200 -12.32 6.51 0 0 158.5 346.88 1000 88.76 99999 88.76 796.1 140.35 0 21.8 0
mm kN kNm kN kNm mm mm2 mm kN kN kN kN kN kN #.# mm2/mm 2475 -17.17 2.45 0 0 158.5 346.88 1000 88.76 99999 88.76 796.1 140.35 0 21.8 0
1 24.28 -15.65 0 0 158.5 346.88 1000 0 0 0 796.1 0 0 0 2590 -18.72 1.24 0 0 158.5 346.88 1000 88.76 99999 88.76 796.1 140.35 0 21.8 0
160 21.48 -12.01 0 0 158.5 346.88 1000 88.76 99999 88.76 796.1 140.35 0 21.8 0 2700 -20.66 -0.92 0 0 158.5 346.64 1000 88.76 99999 88.76 796.1 140.35 0 21.8 0
243 20.02 -10.29 0 0 158.5 346.88 1000 88.76 99999 88.76 796.1 140.35 0 21.8 0 2810 -22.6 -3.3 0 0 158.5 346.88 1000 88.76 99999 88.76 796.1 140.35 0 21.8 0
326 18.66 -8.85 0 0 158.5 346.88 1000 88.76 99999 88.76 796.1 140.35 0 21.8 0 2920 -24.4 -5.6 0 0 158.5 346.88 1000 88.76 99999 88.76 796.1 140.35 0 21.8 0
409 17.2 -7.37 0 0 158.5 346.88 1000 88.76 99999 88.76 796.1 140.35 0 21.8 0 3030 -26.34 -8.39 0 0 158.5 346.88 1000 88.76 99999 88.76 796.1 140.35 0 21.8 0
492 15.74 -6 0 0 158.5 346.88 1000 88.76 99999 88.76 796.1 140.35 0 21.8 0 3140 -28.28 -11.4 0 0 158.5 346.88 1000 88.76 99999 88.76 796.1 140.35 0 21.8 0
575 14.63 -5.22 0 0 158.5 346.88 1000 88.76 99999 88.76 796.1 140.35 0 21.8 0 3299 -31.08 -16.11 0 0 158.5 346.88 1000 0 0 0 796.1 0 0 0
650 13.3 -4.17 0 0 158.5 346.88 1000 88.76 99999 88.76 796.1 140.35 0 21.8 0
816 10.66 -2.9 0 0 158.5 346.88 1000 88.76 99999 88.76 796.1 140.35 0 21.8 0 Spacing of Sets Minimum Legs Shear Comments
982 8.08 -1.32 0 0 158.5 346.88 1000 88.76 99999 88.76 796.1 140.35 0 21.8 0 2 legs 4 legs 6 legs Min legs
1150 6.05 -0.97 0 0 158.5 346.88 1000 88.76 99999 88.76 796.1 140.35 0 21.8 0 H10 H10 H10 H10
1343 -7.35 -1.03 0 0 158.5 346.88 1000 88.76 99999 88.76 796.1 140.35 0 21.8 0 mm mm mm mm # A
1534 -10.09 -2.03 0 0 158.5 346.88 1000 88.76 99999 88.76 796.1 140.35 0 21.8 0
1725 -13.46 -4.28 0 0 158.5 346.88 1000 88.76 99999 88.76 796.1 140.35 0 21.8 0 0 0 0 0 0 No shear steel
1808 -14.58 -4.97 0 0 158.5 346.88 1000 88.76 99999 88.76 796.1 140.35 0 21.8 0 0 0 0 0 0 No shear steel
1891 -16.04 -6.24 0 0 158.5 346.88 1000 88.76 99999 88.76 796.1 140.35 0 21.8 0 0 0 0 0 0 No shear steel
1974 -17.5 -7.63 0 0 158.5 346.88 1000 88.76 99999 88.76 796.1 140.35 0 21.8 0 0 0 0 0 0 No shear steel
2057 -18.86 -8.97 0 0 158.5 346.88 1000 88.76 99999 88.76 796.1 140.35 0 21.8 0 0 0 0 0 0 No shear steel
RAPT 6.6.8.0 Project Name: J110 Page 17/30 RAPT 6.6.8.0 Project Name: J110 Page 18/30
Licensee: AECOM Singapore Pte Ltd 1/6/2022 7:06:42 PM License No.: 10479063400712WPN11 Licensee: AECOM Singapore Pte Ltd 1/6/2022 7:06:46 PM License No.: 10479063400712WPN11
Span 7
Spacing of Sets Minimum Legs Shear Comments Locat V* Mv* Pv Mdec d Ast bv phi Vuc phi Vut phi Vu Phi Vumax phi VuMin phi Vus Theta Asv/s
2 legs 4 legs 6 legs Min legs
H10 H10 H10 H10
mm mm mm mm # A mm kN kNm kN kNm mm mm2 mm kN kN kN kN kN kN #.# mm2/mm
0 0 0 0 0 No shear steel 1 29.96 -14.8 0 0 158.5 346.88 1000 0 0 0 796.1 0 0 0
0 0 0 0 0 No shear steel 160 27.15 -10.26 0 0 158.5 346.88 1000 88.76 99999 88.76 796.1 140.35 0 21.8 0
0 0 0 0 0 No shear steel 250 25.57 -7.89 0 0 158.5 346.88 1000 88.76 99999 88.76 796.1 140.35 0 21.8 0
0 0 0 0 0 No shear steel 340 23.99 -5.88 0 0 158.5 346.88 1000 88.76 99999 88.76 796.1 140.35 0 21.8 0
0 0 0 0 0 No shear steel 430 22.48 -3.78 0 0 158.5 346.88 1000 88.76 99999 88.76 796.1 140.35 0 21.8 0
0 0 0 0 0 No shear steel 520 20.9 -1.83 0 0 158.5 346.88 1000 88.76 99999 88.76 796.1 140.35 0 21.8 0
0 0 0 0 0 No shear steel 610 19.31 -0.02 0 0 158.5 346.64 1000 88.76 99999 88.76 796.1 140.35 0 21.8 0
0 0 0 0 0 No shear steel 700 18.02 1.01 0 0 158.5 346.88 1000 88.76 99999 88.76 796.1 140.35 0 21.8 0
0 0 0 0 0 No shear steel 933 13.92 4.73 0 0 158.5 346.88 1000 88.76 99999 88.76 796.1 140.35 0 21.8 0
0 0 0 0 0 No shear steel 1166 10.38 6.57 0 0 158.5 346.88 1000 88.76 99999 88.76 796.1 140.35 0 21.8 0
0 0 0 0 0 No shear steel 1400 7.14 7.28 0 0 158.5 346.88 1000 88.76 99999 88.76 796.1 140.35 0 21.8 0
0 0 0 0 0 No shear steel 1634 3.37 7.09 0 0 158.5 346.88 1000 88.76 99999 88.76 796.1 140.35 0 21.8 0
0 0 0 0 0 No shear steel 1867 -5.43 9.47 0 0 158.5 346.88 1000 88.76 99999 88.76 796.1 140.35 0 21.8 0
0 0 0 0 0 No shear steel 2100 -9.4 9.06 0 0 158.5 346.88 1000 88.76 99999 88.76 796.1 140.35 0 21.8 0
2190 -10.37 9.14 0 0 158.5 346.88 1000 88.76 99999 88.76 796.1 140.35 0 21.8 0
2280 -11.95 8.14 0 0 158.5 346.88 1000 88.76 99999 88.76 796.1 140.35 0 21.8 0
2370 -13.54 6.99 0 0 158.5 346.88 1000 88.76 99999 88.76 796.1 140.35 0 21.8 0
Span 6 2460 -15.05 5.7 0 0 158.5 346.88 1000 88.76 99999 88.76 796.1 140.35 0 21.8 0
Locat V* Mv* Pv Mdec d Ast bv phi Vuc phi Vut phi Vu Phi Vumax phi VuMin phi Vus Theta Asv/s 2550 -16.5 4.68 0 0 158.5 346.88 1000 88.76 99999 88.76 796.1 140.35 0 21.8 0
2640 -18.09 3.12 0 0 158.5 346.88 1000 88.76 99999 88.76 796.1 140.35 0 21.8 0
2700 -19.15 2 0 0 158.5 346.88 1000 0 0 0 796.1 0 0 0
mm kN kNm kN kNm mm mm2 mm kN kN kN kN kN kN #.# mm2/mm
1 27.01 -16.12 0 0 158.5 346.88 1000 0 0 0 796.1 0 0 0 Spacing of Sets Minimum Legs Shear Comments
160 24.21 -12.05 0 0 158.5 346.88 1000 88.76 99999 88.76 796.1 140.35 0 21.8 0 2 legs 4 legs 6 legs Min legs
268 22.3 -9.54 0 0 158.5 346.88 1000 88.76 99999 88.76 796.1 140.35 0 21.8 0 H10 H10 H10 H10
376 20.52 -7.46 0 0 158.5 346.88 1000 88.76 99999 88.76 796.1 140.35 0 21.8 0 mm mm mm mm # A
484 18.62 -5.34 0 0 158.5 346.88 1000 88.76 99999 88.76 796.1 140.35 0 21.8 0
592 16.71 -3.44 0 0 158.5 346.88 1000 88.76 99999 88.76 796.1 140.35 0 21.8 0 0 0 0 0 0 No shear steel
700 15.22 -2.38 0 0 158.5 346.88 1000 88.76 99999 88.76 796.1 140.35 0 21.8 0 0 0 0 0 0 No shear steel
933 11.12 0.69 0 0 158.5 346.88 1000 88.76 99999 88.76 796.1 140.35 0 21.8 0 0 0 0 0 0 No shear steel
1166 7.76 1.95 0 0 158.5 346.88 1000 88.76 99999 88.76 796.1 140.35 0 21.8 0 0 0 0 0 0 No shear steel
1400 4.76 2.22 0 0 158.5 346.88 1000 88.76 99999 88.76 796.1 140.35 0 21.8 0 0 0 0 0 0 No shear steel
1634 -7.23 2.64 0 0 158.5 346.88 1000 88.76 99999 88.76 796.1 140.35 0 21.8 0 0 0 0 0 0 No shear steel
1867 -10.58 1.5 0 0 158.5 346.88 1000 88.76 99999 88.76 796.1 140.35 0 21.8 0 0 0 0 0 0 No shear steel
2100 -14.69 -1.44 0 0 158.5 346.88 1000 88.76 99999 88.76 796.1 140.35 0 21.8 0 0 0 0 0 0 No shear steel
2208 -16.18 -2.44 0 0 158.5 346.88 1000 88.76 99999 88.76 796.1 140.35 0 21.8 0 0 0 0 0 0 No shear steel
2316 -18.08 -4.29 0 0 158.5 346.88 1000 88.76 99999 88.76 796.1 140.35 0 21.8 0 0 0 0 0 0 No shear steel
2424 -19.99 -6.35 0 0 158.5 346.88 1000 88.76 99999 88.76 796.1 140.35 0 21.8 0 0 0 0 0 0 No shear steel
2532 -21.77 -8.37 0 0 158.5 346.88 1000 88.76 99999 88.76 796.1 140.35 0 21.8 0 0 0 0 0 0 No shear steel
2640 -23.67 -10.82 0 0 158.5 346.88 1000 88.76 99999 88.76 796.1 140.35 0 21.8 0 0 0 0 0 0 No shear steel
2799 -26.47 -14.81 0 0 158.5 346.88 1000 0 0 0 796.1 0 0 0 0 0 0 0 0 No shear steel
0 0 0 0 0 No shear steel
Spacing of Sets Minimum Legs Shear Comments 0 0 0 0 0 No shear steel
2 legs 4 legs 6 legs Min legs 0 0 0 0 0 No shear steel
H10 H10 H10 H10 0 0 0 0 0 No shear steel
mm mm mm mm # A 0 0 0 0 0 No shear steel
0 0 0 0 0 No shear steel
0 0 0 0 0 No shear steel
0 0 0 0 0 No shear steel
0 0 0 0 0 No shear steel
0 0 0 0 0 No shear steel Punching
0 0 0 0 0 No shear steel Column Head Critical Section
0 0 0 0 0 No shear steel Column Bh a at u d fcv P/A Asw/s min V* Mv* V*eff VRd1 VRd2 Asv result
0 0 0 0 0 No shear steel No.
A #.# mm mm mm mm MPa MPa mm2/mm kN kNm kN kN kN mm2 A
0 0 0 0 0 No shear steel
1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Check Not Carried Out!
0 0 0 0 0 No shear steel
2 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Check Not Carried Out!
0 0 0 0 0 No shear steel
3 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Check Not Carried Out!
0 0 0 0 0 No shear steel
4 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Check Not Carried Out!
0 0 0 0 0 No shear steel
5 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Check Not Carried Out!
0 0 0 0 0 No shear steel
6 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Check Not Carried Out!
0 0 0 0 0 No shear steel
7 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Check Not Carried Out!
0 0 0 0 0 No shear steel
8 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Check Not Carried Out!
0 0 0 0 0 No shear steel
RAPT 6.6.8.0 Project Name: J110 Page 19/30 RAPT 6.6.8.0 Project Name: J110 Page 20/30
Licensee: AECOM Singapore Pte Ltd 1/6/2022 7:06:50 PM License No.: 10479063400712WPN11 Licensee: AECOM Singapore Pte Ltd 1/6/2022 7:06:54 PM License No.: 10479063400712WPN11
Deflections Even Spans Loaded
All Spans Loaded Transfer
Transfer
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8 mm
mm 0
0.03 -0.088 -0.016 0.044 -0.202 0.014 -0.165
0 -0.249
0.03 -0.088 -0.016 0.044 -0.202 0.014 -0.165
-0.249
-2
-2
-4
-4 29809 30543 99999 14052 51746 16348 99999 16971
29809 30543 99999 14052 51746 16348 99999 16971 900 3600 6400 9900 12200 15500 18300 21100 mm
900 3600 6400 9900 12200 15500 18300 21100 mm
Short Term
Short Term
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8 mm
mm 0
-0.056 -0.065 -0.11 0.023 -0.229 -0.088 -0.201
0 -0.29
0.057 -0.168 -0.031 0.085 0.027
-0.474 -0.384 -0.314
-2
-2
-4
-4 15993 41252 25429 12072 99631 14395 31861 13922
15657 16050 89726 7385 27190 8592 99999 8920 900 3600 6400 9900 12200 15500 18300 21100 mm
900 3600 6400 9900 12200 15500 18300 21100 mm
All Spans Loaded Odd Spans Loaded Even Spans Loaded
Even Spans Loaded Odd Spans Loaded All Spans Loaded
Incremental
Incremental
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8 mm
mm 0
-0.069 -0.114 0.162 0.063
0 -0.386
0.072 0.104 0.229 0.102 -0.837
-1.22 -1
-0.489 -2
-1.16 -0.95
-2 -1.4
-4
-4 13136 6989 24532 2874 14193 3286 44411 3344
12521 5520 26833 2497 10028 2847 27452 2947 900 3600 6400 9900 12200 15500 18300 21100 mm
900 3600 6400 9900 12200 15500 18300 21100 mm
All Spans Loaded Odd Spans Loaded Even Spans Loaded
Even Spans Loaded Odd Spans Loaded All Spans Loaded
Total Long Term
Total Long Term
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8 mm
mm 0
-0.04 0.204 0.077
0 -0.13
0.093 0.119 0.272 0.115 -0.47
-1.2 -0.994
-0.573 -2 -1.45
-1.35 -1.11
-2 -1.64
-4
-4 22630 5739 21581 2406 11291 2759 36494 2816
9629 4710 23517 2136 8467 2443 24335 2529 900 3600 6400 9900 12200 15500 18300 21100 mm
900 3600 6400 9900 12200 15500 18300 21100 mm
All Spans Loaded Odd Spans Loaded Even Spans Loaded
Even Spans Loaded Odd Spans Loaded All Spans Loaded
RAPT 6.6.8.0 Project Name: J110 Page 21/30 RAPT 6.6.8.0 Project Name: J110 Page 22/30
Licensee: AECOM Singapore Pte Ltd 1/6/2022 7:06:58 PM License No.: 10479063400712WPN11 Licensee: AECOM Singapore Pte Ltd 1/6/2022 7:07:02 PM License No.: 10479063400712WPN11
Odd Spans Loaded Top Reinforcement Bottom Reinforcement
Transfer
Max Max Section Max Max Section
1 2 3 4 5 6 7 8 Locat Size Space Area Depth Width Rebar Reqd Size Space Area Depth Width Rebar Reqd
mm mm mm mm2 mm mm A mm mm mm2 mm mm A
mm 338 32 300 346.88 41.5 1000 5 H10 @ 226.3 0 0 0 158.5 1000 No Steel Added
0 450 32 300 346.88 41.5 1000 5 H10 @ 226.3 0 0 0 158.5 1000 No Steel Added
0.03 -0.088 -0.016 0.044 -0.202 0.014 -0.165
-0.249 563 32 300 346.88 41.5 1000 5 H10 @ 226.3 0 0 0 158.5 1000 No Steel Added
675 32 300 346.88 41.5 1000 5 H10 @ 226.3 0 0 0 158.5 1000 No Steel Added
-2
740 32 300 346.88 41.5 1000 5 H10 @ 226.3 0 0 0 158.5 1000 No Steel Added
820 32 300 346.88 41.5 1000 5 H10 @ 226.3 0 0 0 158.5 1000 No Steel Added
-4 899 32 300 346.88 41.5 1000 5 H10 @ 226.3 0 0 0 158.5 1000 No Steel Added
Shear Reinforcement
29809 30543 99999 14052 51746 16348 99999 16971
Spacing of Sets
900 3600 6400 9900 12200 15500 18300 21100 mm
2 legs 4 legs 6 legs Min legs Minimum Shear
Area H10 H10 H10 H10 Legs Comments
Short Term
mm2/mm mm mm mm mm # A
1 2 3 4 5 6 7 8 0 0 0 0 0 0 No shear steel
0 0 0 0 0 0 No shear steel
mm 0 0 0 0 0 0 No shear steel
0 0 0 0 0 0 0 No shear steel
0.157 0.076 0.134 0.076
-0.229 -0.443 -0.348 0 0 0 0 0 0 No shear steel
-0.539
0 0 0 0 0 0 No shear steel
-2
0 0 0 0 0 0 No shear steel
-4
5737 11794 36774 6489 17209 7451 36958 8041
900 3600 6400 9900 12200 15500 18300 21100 mm Design Comments:-
- - Column Grid 1 - Required Bar Size is smaller than the Preferred Bar Size. Maintaining the same cover will require slightly less reinforcement than
All Spans Loaded Even Spans Loaded Odd Spans Loaded calculated.
Incremental Span 1
Top Reinforcement Bottom Reinforcement
1 2 3 4 5 6 7 8
mm Max Max Section Max Max Section
0 Locat Size Space Area Depth Width Rebar Reqd Size Space Area Depth Width Rebar Reqd
0.145 0.145 0.278 0.143 mm mm mm mm2 mm mm A mm mm mm2 mm mm A
-0.55 1 32 300 346.88 41.5 1000 5 H10 @ 226.3 0 0 0 158.5 1000 No Steel Added
-1.22 -0.984
-2 -1.47 160 32 300 346.88 41.5 1000 5 H10 @ 226.3 0 0 0 158.5 1000 No Steel Added
263 32 300 346.88 41.5 1000 5 H10 @ 226.3 0 0 346.64 158.5 1000 5 H10 @ 226.5
366 32 300 346.88 41.5 1000 5 H10 @ 226.3 32 300 346.64 158.5 1000 5 H10 @ 226.5
-4 469 32 300 346.64 41.5 1000 5 H10 @ 226.5 32 300 346.88 158.5 1000 5 H10 @ 226.3
6223 4911 19247 2385 8285 2710 19516 2844 572 0 0 346.64 41.5 1000 5 H10 @ 226.5 32 300 346.88 158.5 1000 5 H10 @ 226.3
900 3600 6400 9900 12200 15500 18300 21100 mm 675 0 0 346.64 41.5 1000 5 H10 @ 226.5 32 300 346.88 158.5 1000 5 H10 @ 226.3
900 0 0 346.64 41.5 1000 5 H10 @ 226.5 32 300 346.88 158.5 1000 5 H10 @ 226.3
All Spans Loaded Even Spans Loaded Odd Spans Loaded 1125 0 0 0 41.5 1000 No Steel Added 32 300 346.88 158.5 1000 5 H10 @ 226.3
1350 0 0 0 41.5 1000 No Steel Added 32 300 346.88 158.5 1000 5 H10 @ 226.3
Total Long Term
1575 0 0 0 41.5 1000 No Steel Added 32 300 346.88 158.5 1000 5 H10 @ 226.3
1800 0 0 346.64 41.5 1000 5 H10 @ 226.5 32 300 346.88 158.5 1000 5 H10 @ 226.3
1 2 3 4 5 6 7 8
2025 0 0 346.64 41.5 1000 5 H10 @ 226.5 32 300 346.88 158.5 1000 5 H10 @ 226.3
mm 2128 32 300 346.64 41.5 1000 5 H10 @ 226.5 32 300 346.88 158.5 1000 5 H10 @ 226.3
0 0.32 2231 32 300 346.88 41.5 1000 5 H10 @ 226.3 32 300 346.64 158.5 1000 5 H10 @ 226.5
0.173 0.159 0.155
-0.634 2334 32 300 346.88 41.5 1000 5 H10 @ 226.3 0 0 346.64 158.5 1000 5 H10 @ 226.5
-1.14 2437 32 300 346.88 41.5 1000 5 H10 @ 226.3 0 0 0 158.5 1000 No Steel Added
-2 -1.41
-1.7 2540 32 300 346.88 41.5 1000 5 H10 @ 226.3 0 0 0 158.5 1000 No Steel Added
2699 32 300 346.88 41.5 1000 5 H10 @ 226.3 0 0 0 158.5 1000 No Steel Added
-4 Shear Reinforcement
Spacing of Sets
5191 4259 17600 2054 7190 2341 18013 2453
2 legs 4 legs 6 legs Min legs Minimum Shear
900 3600 6400 9900 12200 15500 18300 21100 mm
Area H10 H10 H10 H10 Legs Comments
All Spans Loaded Even Spans Loaded Odd Spans Loaded mm2/mm mm mm mm mm # A
0 0 0 0 0 0 No shear steel
Detailed Reinforcement 0 0 0 0 0 0 No shear steel
Span 0 0 0 0 0 0 0 No shear steel
Top Reinforcement Bottom Reinforcement 0 0 0 0 0 0 No shear steel
0 0 0 0 0 0 No shear steel
Max Max Section Max Max Section 0 0 0 0 0 0 No shear steel
Locat Size Space Area Depth Width Rebar Reqd Size Space Area Depth Width Rebar Reqd 0 0 0 0 0 0 No shear steel
mm mm mm mm2 mm mm A mm mm mm2 mm mm A 0 0 0 0 0 0 No shear steel
100 32 300 346.88 41.5 1000 5 H10 @ 226.3 0 0 0 158.5 1000 No Steel Added 0 0 0 0 0 0 No shear steel
225 32 300 346.88 41.5 1000 5 H10 @ 226.3 0 0 0 158.5 1000 No Steel Added 0 0 0 0 0 0 No shear steel
RAPT 6.6.8.0 Project Name: J110 Page 23/30 RAPT 6.6.8.0 Project Name: J110 Page 24/30
Licensee: AECOM Singapore Pte Ltd 1/6/2022 7:07:06 PM License No.: 10479063400712WPN11 Licensee: AECOM Singapore Pte Ltd 1/6/2022 7:07:10 PM License No.: 10479063400712WPN11
Shear Reinforcement Shear Reinforcement
Spacing of Sets Spacing of Sets
2 legs 4 legs 6 legs Min legs Minimum Shear 2 legs 4 legs 6 legs Min legs Minimum Shear
Area H10 H10 H10 H10 Legs Comments Area H10 H10 H10 H10 Legs Comments
mm2/mm mm mm mm mm # A mm2/mm mm mm mm mm # A
0 0 0 0 0 0 No shear steel 0 0 0 0 0 0 No shear steel
0 0 0 0 0 0 No shear steel
0 0 0 0 0 0 No shear steel
0 0 0 0 0 0 No shear steel Design Comments:-
0 0 0 0 0 0 No shear steel - - Column Grid 2 - Required Bar Size is smaller than the Preferred Bar Size. Maintaining the same cover will require slightly less reinforcement than
0 0 0 0 0 0 No shear steel calculated.
0 0 0 0 0 0 No shear steel - - Column Grid 3 - Required Bar Size is smaller than the Preferred Bar Size. Maintaining the same cover will require slightly less reinforcement than
calculated.
- - Span 2 - Required Bar Size is smaller than the Preferred Bar Size. Maintaining the same cover will require slightly less reinforcement than calculated.
- Span - 2 - Reinforcement added at left span contraflexure point for Offset of Bending Moment Diagram for Shear - 40.14mm2
Design Comments:- - Span - 2 - Reinforcement added at right span contraflexure point for Offset of Bending Moment Diagram for Shear - 40.13mm2
- - Column Grid 1 - Required Bar Size is smaller than the Preferred Bar Size. Maintaining the same cover will require slightly less reinforcement than
calculated.
- - Column Grid 2 - Required Bar Size is smaller than the Preferred Bar Size. Maintaining the same cover will require slightly less reinforcement than Span 3
calculated. Top Reinforcement Bottom Reinforcement
- - Span 1 - Required Bar Size is smaller than the Preferred Bar Size. Maintaining the same cover will require slightly less reinforcement than calculated.
- Span - 1 - Reinforcement added at left support contraflexure point for Offset of Bending Moment Diagram for Shear - 6.01mm2 Max Max Section Max Max Section
- Span - 1 - Reinforcement added at right support contraflexure point for Offset of Bending Moment Diagram for Shear - 6.29mm2 Locat Size Space Area Depth Width Rebar Reqd Size Space Area Depth Width Rebar Reqd
- Span - 1 - Reinforcement added at left span contraflexure point for Offset of Bending Moment Diagram for Shear - 46.79mm2 mm mm mm mm2 mm mm A mm mm mm2 mm mm A
- Span - 1 - Reinforcement added at right span contraflexure point for Offset of Bending Moment Diagram for Shear - 43.24mm2 1 25 270.1 346.88 41.5 1000 5 H10 @ 226.3 0 0 0 158.5 1000 No Steel Added
160 32 300 346.88 41.5 1000 5 H10 @ 226.3 0 0 0 158.5 1000 No Steel Added
Span 2 279 32 300 346.88 41.5 1000 5 H10 @ 226.3 0 0 0 158.5 1000 No Steel Added
Top Reinforcement Bottom Reinforcement 398 32 300 346.88 41.5 1000 5 H10 @ 226.3 0 0 0 158.5 1000 No Steel Added
517 32 300 346.88 41.5 1000 5 H10 @ 226.3 0 0 346.64 158.5 1000 5 H10 @ 226.5
Max Max Section Max Max Section 636 32 300 346.64 41.5 1000 5 H10 @ 226.5 32 300 346.88 158.5 1000 5 H10 @ 226.3
Locat Size Space Area Depth Width Rebar Reqd Size Space Area Depth Width Rebar Reqd 755 0 0 346.64 41.5 1000 5 H10 @ 226.5 32 300 346.88 158.5 1000 5 H10 @ 226.3
mm mm mm mm2 mm mm A mm mm mm2 mm mm A 875 0 0 346.64 41.5 1000 5 H10 @ 226.5 32 300 346.88 158.5 1000 5 H10 @ 226.3
1 32 300 346.88 41.5 1000 5 H10 @ 226.3 0 0 0 158.5 1000 No Steel Added 1166 0 0 0 41.5 1000 No Steel Added 32 300 346.88 158.5 1000 5 H10 @ 226.3
160 32 300 346.88 41.5 1000 5 H10 @ 226.3 0 0 0 158.5 1000 No Steel Added 1457 0 0 0 41.5 1000 No Steel Added 32 300 346.88 158.5 1000 5 H10 @ 226.3
268 32 300 346.88 41.5 1000 5 H10 @ 226.3 0 0 0 158.5 1000 No Steel Added 1750 0 0 0 41.5 1000 No Steel Added 32 300 346.88 158.5 1000 5 H10 @ 226.3
376 32 300 346.88 41.5 1000 5 H10 @ 226.3 0 0 0 158.5 1000 No Steel Added 2043 0 0 0 41.5 1000 No Steel Added 32 300 346.88 158.5 1000 5 H10 @ 226.3
484 32 300 346.88 41.5 1000 5 H10 @ 226.3 0 0 346.64 158.5 1000 5 H10 @ 226.5 2334 0 0 0 41.5 1000 No Steel Added 32 300 346.88 158.5 1000 5 H10 @ 226.3
592 32 300 346.88 41.5 1000 5 H10 @ 226.3 32 300 346.64 158.5 1000 5 H10 @ 226.5 2625 0 0 0 41.5 1000 No Steel Added 32 300 346.88 158.5 1000 5 H10 @ 226.3
700 32 300 346.64 41.5 1000 5 H10 @ 226.5 32 300 346.88 158.5 1000 5 H10 @ 226.3 2745 0 0 0 41.5 1000 No Steel Added 32 300 346.88 158.5 1000 5 H10 @ 226.3
933 0 0 346.64 41.5 1000 5 H10 @ 226.5 32 300 346.88 158.5 1000 5 H10 @ 226.3 2864 0 0 346.64 41.5 1000 5 H10 @ 226.5 32 300 346.88 158.5 1000 5 H10 @ 226.3
1166 0 0 346.64 41.5 1000 5 H10 @ 226.5 32 300 346.88 158.5 1000 5 H10 @ 226.3 2983 32 300 346.88 41.5 1000 5 H10 @ 226.3 32 300 346.64 158.5 1000 5 H10 @ 226.5
1400 0 0 346.64 41.5 1000 5 H10 @ 226.5 32 300 346.88 158.5 1000 5 H10 @ 226.3 3102 32 300 346.88 41.5 1000 5 H10 @ 226.3 0 0 346.64 158.5 1000 5 H10 @ 226.5
1634 32 300 346.64 41.5 1000 5 H10 @ 226.5 32 300 346.88 158.5 1000 5 H10 @ 226.3 3221 32 300 346.88 41.5 1000 5 H10 @ 226.3 0 0 0 158.5 1000 No Steel Added
1867 32 300 346.64 41.5 1000 5 H10 @ 226.5 32 300 346.88 158.5 1000 5 H10 @ 226.3 3340 32 300 346.88 41.5 1000 5 H10 @ 226.3 0 0 0 158.5 1000 No Steel Added
2100 32 300 346.88 41.5 1000 5 H10 @ 226.3 32 300 346.64 158.5 1000 5 H10 @ 226.5 3499 32 300 346.88 41.5 1000 5 H10 @ 226.3 0 0 0 158.5 1000 No Steel Added
2208 32 300 346.88 41.5 1000 5 H10 @ 226.3 0 0 346.64 158.5 1000 5 H10 @ 226.5 Shear Reinforcement
2316 32 300 346.88 41.5 1000 5 H10 @ 226.3 0 0 0 158.5 1000 No Steel Added Spacing of Sets
2424 32 300 346.88 41.5 1000 5 H10 @ 226.3 0 0 0 158.5 1000 No Steel Added 2 legs 4 legs 6 legs Min legs Minimum Shear
2532 32 300 346.88 41.5 1000 5 H10 @ 226.3 0 0 0 158.5 1000 No Steel Added Area H10 H10 H10 H10 Legs Comments
2640 32 300 346.88 41.5 1000 5 H10 @ 226.3 0 0 0 158.5 1000 No Steel Added mm2/mm mm mm mm mm # A
2799 25 270 346.88 41.5 1000 5 H10 @ 226.3 0 0 0 158.5 1000 No Steel Added
Shear Reinforcement 0 0 0 0 0 0 No shear steel
Spacing of Sets 0 0 0 0 0 0 No shear steel
2 legs 4 legs 6 legs Min legs Minimum Shear 0 0 0 0 0 0 No shear steel
Area H10 H10 H10 H10 Legs Comments 0 0 0 0 0 0 No shear steel
mm2/mm mm mm mm mm # A 0 0 0 0 0 0 No shear steel
0 0 0 0 0 0 No shear steel
0 0 0 0 0 0 No shear steel 0 0 0 0 0 0 No shear steel
0 0 0 0 0 0 No shear steel 0 0 0 0 0 0 No shear steel
0 0 0 0 0 0 No shear steel 0 0 0 0 0 0 No shear steel
0 0 0 0 0 0 No shear steel 0 0 0 0 0 0 No shear steel
0 0 0 0 0 0 No shear steel 0 0 0 0 0 0 No shear steel
0 0 0 0 0 0 No shear steel 0 0 0 0 0 0 No shear steel
0 0 0 0 0 0 No shear steel 0 0 0 0 0 0 No shear steel
0 0 0 0 0 0 No shear steel 0 0 0 0 0 0 No shear steel
0 0 0 0 0 0 No shear steel 0 0 0 0 0 0 No shear steel
0 0 0 0 0 0 No shear steel 0 0 0 0 0 0 No shear steel
0 0 0 0 0 0 No shear steel 0 0 0 0 0 0 No shear steel
0 0 0 0 0 0 No shear steel 0 0 0 0 0 0 No shear steel
0 0 0 0 0 0 No shear steel 0 0 0 0 0 0 No shear steel
0 0 0 0 0 0 No shear steel
0 0 0 0 0 0 No shear steel
0 0 0 0 0 0 No shear steel
RAPT 6.6.8.0 Project Name: J110 Page 25/30 RAPT 6.6.8.0 Project Name: J110 Page 26/30
Licensee: AECOM Singapore Pte Ltd 1/6/2022 7:07:15 PM License No.: 10479063400712WPN11 Licensee: AECOM Singapore Pte Ltd 1/6/2022 7:07:19 PM License No.: 10479063400712WPN11
Design Comments:- Design Comments:-
- - Column Grid 3 - Required Bar Size is smaller than the Preferred Bar Size. Maintaining the same cover will require slightly less reinforcement than - - Column Grid 4 - Required Bar Size is smaller than the Preferred Bar Size. Maintaining the same cover will require slightly less reinforcement than
calculated. calculated.
- - Column Grid 4 - Required Bar Size is smaller than the Preferred Bar Size. Maintaining the same cover will require slightly less reinforcement than - - Column Grid 5 - Required Bar Size is smaller than the Preferred Bar Size. Maintaining the same cover will require slightly less reinforcement than
calculated. calculated.
- - Span 3 - Required Bar Size is smaller than the Preferred Bar Size. Maintaining the same cover will require slightly less reinforcement than calculated. - - Span 4 - Required Bar Size is smaller than the Preferred Bar Size. Maintaining the same cover will require slightly less reinforcement than calculated.
- Span - 3 - Reinforcement added at left support contraflexure point for Offset of Bending Moment Diagram for Shear - 20.41mm2 - Span - 4 - Reinforcement added at left span contraflexure point for Offset of Bending Moment Diagram for Shear - 31.77mm2
- Span - 3 - Reinforcement added at right support contraflexure point for Offset of Bending Moment Diagram for Shear - 20.47mm2 - Span - 4 - Reinforcement added at right span contraflexure point for Offset of Bending Moment Diagram for Shear - 29.18mm2
- Span - 3 - Reinforcement added at left span contraflexure point for Offset of Bending Moment Diagram for Shear - 52.31mm2
- Span - 3 - Reinforcement added at right span contraflexure point for Offset of Bending Moment Diagram for Shear - 23.88mm2
Span 5
Top Reinforcement Bottom Reinforcement
Span 4
Top Reinforcement Bottom Reinforcement Max Max Section Max Max Section
Locat Size Space Area Depth Width Rebar Reqd Size Space Area Depth Width Rebar Reqd
Max Max Section Max Max Section mm mm mm mm2 mm mm A mm mm mm2 mm mm A
Locat Size Space Area Depth Width Rebar Reqd Size Space Area Depth Width Rebar Reqd 1 32 300 346.88 41.5 1000 5 H10 @ 226.3 0 0 0 158.5 1000 No Steel Added
mm mm mm mm2 mm mm A mm mm mm2 mm mm A 160 32 300 346.88 41.5 1000 5 H10 @ 226.3 0 0 0 158.5 1000 No Steel Added
1 32 300 346.88 41.5 1000 5 H10 @ 226.3 0 0 0 158.5 1000 No Steel Added 270 32 300 346.88 41.5 1000 5 H10 @ 226.3 0 0 0 158.5 1000 No Steel Added
80 32 300 346.88 41.5 1000 5 H10 @ 226.3 0 0 0 158.5 1000 No Steel Added 380 32 300 346.88 41.5 1000 5 H10 @ 226.3 0 0 346.64 158.5 1000 5 H10 @ 226.5
160 32 300 346.88 41.5 1000 5 H10 @ 226.3 0 0 0 158.5 1000 No Steel Added 490 32 300 346.88 41.5 1000 5 H10 @ 226.3 32 300 346.64 158.5 1000 5 H10 @ 226.5
243 32 300 346.88 41.5 1000 5 H10 @ 226.3 0 0 0 158.5 1000 No Steel Added 600 0 0 346.64 41.5 1000 5 H10 @ 226.5 32 300 346.88 158.5 1000 5 H10 @ 226.3
326 32 300 346.88 41.5 1000 5 H10 @ 226.3 0 0 0 158.5 1000 No Steel Added 710 0 0 0 41.5 1000 No Steel Added 32 300 346.88 158.5 1000 5 H10 @ 226.3
409 32 300 346.88 41.5 1000 5 H10 @ 226.3 0 0 0 158.5 1000 No Steel Added 825 0 0 0 41.5 1000 No Steel Added 32 300 346.88 158.5 1000 5 H10 @ 226.3
492 32 300 346.88 41.5 1000 5 H10 @ 226.3 0 0 0 158.5 1000 No Steel Added 1100 0 0 0 41.5 1000 No Steel Added 32 300 346.88 158.5 1000 5 H10 @ 226.3
575 32 300 346.88 41.5 1000 5 H10 @ 226.3 0 0 346.64 158.5 1000 5 H10 @ 226.5 1375 0 0 0 41.5 1000 No Steel Added 32 300 346.88 158.5 1000 5 H10 @ 226.3
650 32 300 346.88 41.5 1000 5 H10 @ 226.3 0 0 346.64 158.5 1000 5 H10 @ 226.5 1650 0 0 0 41.5 1000 No Steel Added 32 300 346.88 158.5 1000 5 H10 @ 226.3
816 32 300 346.88 41.5 1000 5 H10 @ 226.3 32 300 346.64 158.5 1000 5 H10 @ 226.5 1925 0 0 0 41.5 1000 No Steel Added 32 300 346.88 158.5 1000 5 H10 @ 226.3
982 32 300 346.88 41.5 1000 5 H10 @ 226.3 32 300 346.64 158.5 1000 5 H10 @ 226.5 2200 0 0 0 41.5 1000 No Steel Added 32 300 346.88 158.5 1000 5 H10 @ 226.3
1150 32 300 346.88 41.5 1000 5 H10 @ 226.3 32 300 346.64 158.5 1000 5 H10 @ 226.5 2475 0 0 346.64 41.5 1000 5 H10 @ 226.5 32 300 346.88 158.5 1000 5 H10 @ 226.3
1343 32 300 346.88 41.5 1000 5 H10 @ 226.3 32 300 346.64 158.5 1000 5 H10 @ 226.5 2590 0 0 346.64 41.5 1000 5 H10 @ 226.5 32 300 346.88 158.5 1000 5 H10 @ 226.3
1534 32 300 346.88 41.5 1000 5 H10 @ 226.3 32 300 346.64 158.5 1000 5 H10 @ 226.5 2700 32 300 346.64 41.5 1000 5 H10 @ 226.5 32 300 346.88 158.5 1000 5 H10 @ 226.3
1725 32 300 346.88 41.5 1000 5 H10 @ 226.3 0 0 346.64 158.5 1000 5 H10 @ 226.5 2810 32 300 346.88 41.5 1000 5 H10 @ 226.3 0 0 346.64 158.5 1000 5 H10 @ 226.5
1808 32 300 346.88 41.5 1000 5 H10 @ 226.3 0 0 346.64 158.5 1000 5 H10 @ 226.5 2920 32 300 346.88 41.5 1000 5 H10 @ 226.3 0 0 0 158.5 1000 No Steel Added
1891 32 300 346.88 41.5 1000 5 H10 @ 226.3 0 0 0 158.5 1000 No Steel Added 3030 32 300 346.88 41.5 1000 5 H10 @ 226.3 0 0 0 158.5 1000 No Steel Added
1974 32 300 346.88 41.5 1000 5 H10 @ 226.3 0 0 0 158.5 1000 No Steel Added 3140 32 300 346.88 41.5 1000 5 H10 @ 226.3 0 0 0 158.5 1000 No Steel Added
2057 32 300 346.88 41.5 1000 5 H10 @ 226.3 0 0 0 158.5 1000 No Steel Added 3299 25 294 346.88 41.5 1000 5 H10 @ 226.3 0 0 0 158.5 1000 No Steel Added
2140 32 300 346.88 41.5 1000 5 H10 @ 226.3 0 0 0 158.5 1000 No Steel Added Shear Reinforcement
2220 32 300 346.88 41.5 1000 5 H10 @ 226.3 0 0 0 158.5 1000 No Steel Added Spacing of Sets
2299 32 300 346.88 41.5 1000 5 H10 @ 226.3 0 0 0 158.5 1000 No Steel Added 2 legs 4 legs 6 legs Min legs Minimum Shear
Shear Reinforcement Area H10 H10 H10 H10 Legs Comments
Spacing of Sets mm2/mm mm mm mm mm # A
2 legs 4 legs 6 legs Min legs Minimum Shear
Area H10 H10 H10 H10 Legs Comments 0 0 0 0 0 0 No shear steel
mm2/mm mm mm mm mm # A 0 0 0 0 0 0 No shear steel
0 0 0 0 0 0 No shear steel
0 0 0 0 0 0 No shear steel
0 0 0 0 0 0 No shear steel 0 0 0 0 0 0 No shear steel
0 0 0 0 0 0 No shear steel 0 0 0 0 0 0 No shear steel
0 0 0 0 0 0 No shear steel 0 0 0 0 0 0 No shear steel
0 0 0 0 0 0 No shear steel 0 0 0 0 0 0 No shear steel
0 0 0 0 0 0 No shear steel 0 0 0 0 0 0 No shear steel
0 0 0 0 0 0 No shear steel 0 0 0 0 0 0 No shear steel
0 0 0 0 0 0 No shear steel 0 0 0 0 0 0 No shear steel
0 0 0 0 0 0 No shear steel 0 0 0 0 0 0 No shear steel
0 0 0 0 0 0 No shear steel 0 0 0 0 0 0 No shear steel
0 0 0 0 0 0 No shear steel 0 0 0 0 0 0 No shear steel
0 0 0 0 0 0 No shear steel 0 0 0 0 0 0 No shear steel
0 0 0 0 0 0 No shear steel 0 0 0 0 0 0 No shear steel
0 0 0 0 0 0 No shear steel 0 0 0 0 0 0 No shear steel
0 0 0 0 0 0 No shear steel 0 0 0 0 0 0 No shear steel
0 0 0 0 0 0 No shear steel 0 0 0 0 0 0 No shear steel
0 0 0 0 0 0 No shear steel
0 0 0 0 0 0 No shear steel
0 0 0 0 0 0 No shear steel
RAPT 6.6.8.0 Project Name: J110 Page 27/30 RAPT 6.6.8.0 Project Name: J110 Page 28/30
Licensee: AECOM Singapore Pte Ltd 1/6/2022 7:07:23 PM License No.: 10479063400712WPN11 Licensee: AECOM Singapore Pte Ltd 1/6/2022 7:07:27 PM License No.: 10479063400712WPN11
Design Comments:- Span 7
- - Column Grid 5 - Required Bar Size is smaller than the Preferred Bar Size. Maintaining the same cover will require slightly less reinforcement than Top Reinforcement Bottom Reinforcement
calculated.
- - Column Grid 6 - Required Bar Size is smaller than the Preferred Bar Size. Maintaining the same cover will require slightly less reinforcement than
Max Max Section Max Max Section
calculated.
Locat Size Space Area Depth Width Rebar Reqd Size Space Area Depth Width Rebar Reqd
- - Span 5 - Required Bar Size is smaller than the Preferred Bar Size. Maintaining the same cover will require slightly less reinforcement than calculated.
mm mm mm mm2 mm mm A mm mm mm2 mm mm A
- Span - 5 - Reinforcement added at left support contraflexure point for Offset of Bending Moment Diagram for Shear - 18.85mm2
- Span - 5 - Reinforcement added at right support contraflexure point for Offset of Bending Moment Diagram for Shear - 18.74mm2 1 32 300 346.88 41.5 1000 5 H10 @ 226.3 0 0 0 158.5 1000 No Steel Added
- Span - 5 - Reinforcement added at left span contraflexure point for Offset of Bending Moment Diagram for Shear - 22.34mm2 160 32 300 346.88 41.5 1000 5 H10 @ 226.3 0 0 0 158.5 1000 No Steel Added
- Span - 5 - Reinforcement added at right span contraflexure point for Offset of Bending Moment Diagram for Shear - 52.02mm2 250 32 300 346.88 41.5 1000 5 H10 @ 226.3 0 0 0 158.5 1000 No Steel Added
340 32 300 346.88 41.5 1000 5 H10 @ 226.3 0 0 0 158.5 1000 No Steel Added
Span 6 430 32 300 346.88 41.5 1000 5 H10 @ 226.3 0 0 346.64 158.5 1000 5 H10 @ 226.5
Top Reinforcement Bottom Reinforcement 520 32 300 346.88 41.5 1000 5 H10 @ 226.3 32 300 346.64 158.5 1000 5 H10 @ 226.5
610 32 300 346.64 41.5 1000 5 H10 @ 226.5 32 300 346.88 158.5 1000 5 H10 @ 226.3
Max Max Section Max Max Section 700 0 0 346.64 41.5 1000 5 H10 @ 226.5 32 300 346.88 158.5 1000 5 H10 @ 226.3
Locat Size Space Area Depth Width Rebar Reqd Size Space Area Depth Width Rebar Reqd 933 0 0 0 41.5 1000 No Steel Added 32 300 346.88 158.5 1000 5 H10 @ 226.3
mm mm mm mm2 mm mm A mm mm mm2 mm mm A 1166 0 0 0 41.5 1000 No Steel Added 32 300 346.88 158.5 1000 5 H10 @ 226.3
1 25 294 346.88 41.5 1000 5 H10 @ 226.3 0 0 0 158.5 1000 No Steel Added 1400 0 0 0 41.5 1000 No Steel Added 32 300 346.88 158.5 1000 5 H10 @ 226.3
160 32 300 346.88 41.5 1000 5 H10 @ 226.3 0 0 0 158.5 1000 No Steel Added 1634 0 0 0 41.5 1000 No Steel Added 32 300 346.88 158.5 1000 5 H10 @ 226.3
268 32 300 346.88 41.5 1000 5 H10 @ 226.3 0 0 0 158.5 1000 No Steel Added 1867 0 0 0 41.5 1000 No Steel Added 32 300 346.88 158.5 1000 5 H10 @ 226.3
376 32 300 346.88 41.5 1000 5 H10 @ 226.3 0 0 0 158.5 1000 No Steel Added 2100 0 0 0 41.5 1000 No Steel Added 32 300 346.88 158.5 1000 5 H10 @ 226.3
484 32 300 346.88 41.5 1000 5 H10 @ 226.3 0 0 0 158.5 1000 No Steel Added 2190 0 0 0 41.5 1000 No Steel Added 32 300 346.88 158.5 1000 5 H10 @ 226.3
592 32 300 346.88 41.5 1000 5 H10 @ 226.3 0 0 346.64 158.5 1000 5 H10 @ 226.5 2280 0 0 0 41.5 1000 No Steel Added 32 300 346.88 158.5 1000 5 H10 @ 226.3
700 32 300 346.88 41.5 1000 5 H10 @ 226.3 32 300 346.64 158.5 1000 5 H10 @ 226.5 2370 0 0 0 41.5 1000 No Steel Added 32 300 346.88 158.5 1000 5 H10 @ 226.3
933 32 300 346.64 41.5 1000 5 H10 @ 226.5 32 300 346.88 158.5 1000 5 H10 @ 226.3 2460 0 0 0 41.5 1000 No Steel Added 32 300 346.88 158.5 1000 5 H10 @ 226.3
1166 32 300 346.64 41.5 1000 5 H10 @ 226.5 32 300 346.88 158.5 1000 5 H10 @ 226.3 2550 0 0 0 41.5 1000 No Steel Added 32 300 346.88 158.5 1000 5 H10 @ 226.3
1400 0 0 346.64 41.5 1000 5 H10 @ 226.5 32 300 346.88 158.5 1000 5 H10 @ 226.3 2640 0 0 0 41.5 1000 No Steel Added 32 300 346.88 158.5 1000 5 H10 @ 226.3
1634 0 0 346.64 41.5 1000 5 H10 @ 226.5 32 300 346.88 158.5 1000 5 H10 @ 226.3 2700 0 0 0 41.5 1000 No Steel Added 32 300 346.88 158.5 1000 5 H10 @ 226.3
1867 32 300 346.64 41.5 1000 5 H10 @ 226.5 32 300 346.88 158.5 1000 5 H10 @ 226.3 Shear Reinforcement
2100 32 300 346.88 41.5 1000 5 H10 @ 226.3 32 300 346.64 158.5 1000 5 H10 @ 226.5 Spacing of Sets
2208 32 300 346.88 41.5 1000 5 H10 @ 226.3 0 0 346.64 158.5 1000 5 H10 @ 226.5 2 legs 4 legs 6 legs Min legs Minimum Shear
2316 32 300 346.88 41.5 1000 5 H10 @ 226.3 0 0 0 158.5 1000 No Steel Added Area H10 H10 H10 H10 Legs Comments
2424 32 300 346.88 41.5 1000 5 H10 @ 226.3 0 0 0 158.5 1000 No Steel Added mm2/mm mm mm mm mm # A
2532 32 300 346.88 41.5 1000 5 H10 @ 226.3 0 0 0 158.5 1000 No Steel Added
2640 32 300 346.88 41.5 1000 5 H10 @ 226.3 0 0 0 158.5 1000 No Steel Added 0 0 0 0 0 0 No shear steel
2799 32 300 346.88 41.5 1000 5 H10 @ 226.3 0 0 0 158.5 1000 No Steel Added 0 0 0 0 0 0 No shear steel
Shear Reinforcement 0 0 0 0 0 0 No shear steel
Spacing of Sets 0 0 0 0 0 0 No shear steel
2 legs 4 legs 6 legs Min legs Minimum Shear 0 0 0 0 0 0 No shear steel
Area H10 H10 H10 H10 Legs Comments 0 0 0 0 0 0 No shear steel
mm2/mm mm mm mm mm # A 0 0 0 0 0 0 No shear steel
0 0 0 0 0 0 No shear steel
0 0 0 0 0 0 No shear steel 0 0 0 0 0 0 No shear steel
0 0 0 0 0 0 No shear steel 0 0 0 0 0 0 No shear steel
0 0 0 0 0 0 No shear steel 0 0 0 0 0 0 No shear steel
0 0 0 0 0 0 No shear steel 0 0 0 0 0 0 No shear steel
0 0 0 0 0 0 No shear steel 0 0 0 0 0 0 No shear steel
0 0 0 0 0 0 No shear steel 0 0 0 0 0 0 No shear steel
0 0 0 0 0 0 No shear steel 0 0 0 0 0 0 No shear steel
0 0 0 0 0 0 No shear steel 0 0 0 0 0 0 No shear steel
0 0 0 0 0 0 No shear steel 0 0 0 0 0 0 No shear steel
0 0 0 0 0 0 No shear steel 0 0 0 0 0 0 No shear steel
0 0 0 0 0 0 No shear steel 0 0 0 0 0 0 No shear steel
0 0 0 0 0 0 No shear steel
0 0 0 0 0 0 No shear steel
0 0 0 0 0 0 No shear steel Design Comments:-
0 0 0 0 0 0 No shear steel - - Column Grid 7 - Required Bar Size is smaller than the Preferred Bar Size. Maintaining the same cover will require slightly less reinforcement than
0 0 0 0 0 0 No shear steel calculated.
0 0 0 0 0 0 No shear steel - - Span 7 - Required Bar Size is smaller than the Preferred Bar Size. Maintaining the same cover will require slightly less reinforcement than calculated.
- Span - 7 - Reinforcement added at left support contraflexure point for Offset of Bending Moment Diagram for Shear - 20.93mm2
- Span - 7 - Reinforcement added at left span contraflexure point for Offset of Bending Moment Diagram for Shear - 44.09mm2
- Span - 7 - Reinforcement added at right span contraflexure point for Offset of Bending Moment Diagram for Shear - 60.07mm2
Design Comments:-
- - Column Grid 6 - Required Bar Size is smaller than the Preferred Bar Size. Maintaining the same cover will require slightly less reinforcement than
calculated.
- - Column Grid 7 - Required Bar Size is smaller than the Preferred Bar Size. Maintaining the same cover will require slightly less reinforcement than
calculated.
- - Span 6 - Required Bar Size is smaller than the Preferred Bar Size. Maintaining the same cover will require slightly less reinforcement than calculated.
- Span - 6 - Reinforcement added at left span contraflexure point for Offset of Bending Moment Diagram for Shear - 38.47mm2
- Span - 6 - Reinforcement added at right span contraflexure point for Offset of Bending Moment Diagram for Shear - 33.74mm2
RAPT 6.6.8.0 Project Name: J110 Page 29/30 RAPT 6.6.8.0 Project Name: J110 Page 30/30
Licensee: AECOM Singapore Pte Ltd 1/6/2022 7:07:33 PM License No.: 10479063400712WPN11 Licensee: AECOM Singapore Pte Ltd 1/6/2022 7:07:37 PM License No.: 10479063400712WPN11
Reinforcement Layout - - Column Grid 5 - Required Bar Size is smaller than the Preferred Bar Size. Maintaining the same cover will require slightly less reinforcement than
calculated.
1 2 3 4 - - Column Grid 6 - Required Bar Size is smaller than the Preferred Bar Size. Maintaining the same cover will require slightly less reinforcement than
mm calculated.
5-H10
5-H10
5-H10
5-H10
0 - - Span 5 - Required Bar Size is smaller than the Preferred Bar Size. Maintaining the same cover will require slightly less reinforcement than calculated.
- Span - 5 - Reinforcement added at left span contraflexure point for Offset of Bending Moment Diagram for Shear - 22.34mm2
-50 - Span - 5 - Reinforcement added at right span contraflexure point for Offset of Bending Moment Diagram for Shear - 52.02mm2
-100 - - Column Grid 6 - Required Bar Size is smaller than the Preferred Bar Size. Maintaining the same cover will require slightly less reinforcement than
calculated.
-150 - - Column Grid 7 - Required Bar Size is smaller than the Preferred Bar Size. Maintaining the same cover will require slightly less reinforcement than
5-H10
5-H10
5-H10
calculated.
-200 - - Span 6 - Required Bar Size is smaller than the Preferred Bar Size. Maintaining the same cover will require slightly less reinforcement than calculated.
900 3600 6400 9900 - Span - 6 - Reinforcement added at left span contraflexure point for Offset of Bending Moment Diagram for Shear - 38.47mm2
- Span - 6 - Reinforcement added at right span contraflexure point for Offset of Bending Moment Diagram for Shear - 33.74mm2
5 6 7 8
- - Column Grid 7 - Required Bar Size is smaller than the Preferred Bar Size. Maintaining the same cover will require slightly less reinforcement than
5-H10
5-H10
5-H10
0 calculated.
- - Span 7 - Required Bar Size is smaller than the Preferred Bar Size. Maintaining the same cover will require slightly less reinforcement than calculated.
-50 - Span - 7 - Reinforcement added at left span contraflexure point for Offset of Bending Moment Diagram for Shear - 44.09mm2
- Span - 7 - Reinforcement added at right span contraflexure point for Offset of Bending Moment Diagram for Shear - 60.07mm2
-100
-150
5-H10
5-H10
5-H10
5-H10
-200
12200 15500 18300 21100 mm
Flat slabs - slabs which rely on flexural action through the slab or slab thickenings such as drop panels or band beams to discrete column supports, require
concentration of the top reinforcement and tendons over supports within a defined width from the column face to facilitate moment transfer to the column. This
width varies and the amount of reinforcement varies for different design codes. In the major codes, the requirements are specified in AS3600 cl 9.1.2,
Eurocode 1992 - 1 - 1 2004 cl 9.4.1, ACI318-14 cl 8.4.2.3 and BS8110 cl3.7.3.1. For example AS3600 requires that 25% of total negative moment for the
entire slab panel be resisted by reinforcement within a width D either side of the column. RAPT cannot define this concentration as it does not know the
transverse spacing of the tendons. It is the designer's responsibility to ensure that these clauses are complied with.
- - Column Grid 1 - Required Bar Size is smaller than the Preferred Bar Size. Maintaining the same cover will require slightly less reinforcement than
calculated.
- - Column Grid 1 - Required Bar Size is smaller than the Preferred Bar Size. Maintaining the same cover will require slightly less reinforcement than
calculated.
- - Column Grid 2 - Required Bar Size is smaller than the Preferred Bar Size. Maintaining the same cover will require slightly less reinforcement than
calculated.
- - Span 1 - Required Bar Size is smaller than the Preferred Bar Size. Maintaining the same cover will require slightly less reinforcement than calculated.
- Span - 1 - Reinforcement added at left span contraflexure point for Offset of Bending Moment Diagram for Shear - 46.79mm2
- Span - 1 - Reinforcement added at right span contraflexure point for Offset of Bending Moment Diagram for Shear - 43.24mm2
- - Column Grid 2 - Required Bar Size is smaller than the Preferred Bar Size. Maintaining the same cover will require slightly less reinforcement than
calculated.
- - Column Grid 3 - Required Bar Size is smaller than the Preferred Bar Size. Maintaining the same cover will require slightly less reinforcement than
calculated.
- - Span 2 - Required Bar Size is smaller than the Preferred Bar Size. Maintaining the same cover will require slightly less reinforcement than calculated.
- Span - 2 - Reinforcement added at left span contraflexure point for Offset of Bending Moment Diagram for Shear - 40.14mm2
- Span - 2 - Reinforcement added at right span contraflexure point for Offset of Bending Moment Diagram for Shear - 40.13mm2
- - Column Grid 3 - Required Bar Size is smaller than the Preferred Bar Size. Maintaining the same cover will require slightly less reinforcement than
calculated.
- - Column Grid 4 - Required Bar Size is smaller than the Preferred Bar Size. Maintaining the same cover will require slightly less reinforcement than
calculated.
- - Span 3 - Required Bar Size is smaller than the Preferred Bar Size. Maintaining the same cover will require slightly less reinforcement than calculated.
- Span - 3 - Reinforcement added at left span contraflexure point for Offset of Bending Moment Diagram for Shear - 52.31mm2
- Span - 3 - Reinforcement added at right span contraflexure point for Offset of Bending Moment Diagram for Shear - 23.88mm2
- - Column Grid 4 - Required Bar Size is smaller than the Preferred Bar Size. Maintaining the same cover will require slightly less reinforcement than
calculated.
- - Column Grid 5 - Required Bar Size is smaller than the Preferred Bar Size. Maintaining the same cover will require slightly less reinforcement than
calculated.
- - Span 4 - Required Bar Size is smaller than the Preferred Bar Size. Maintaining the same cover will require slightly less reinforcement than calculated.
- Span - 4 - Reinforcement added at left span contraflexure point for Offset of Bending Moment Diagram for Shear - 31.77mm2
- Span - 4 - Reinforcement added at right span contraflexure point for Offset of Bending Moment Diagram for Shear - 29.18mm2
RAPT 6.6.8.0 Project Name: J110 Page 2/13
Licensee: AECOM Singapore Pte Ltd 1/6/2022 6:45:09 PM License No.: 10479063400712WPN11
Project Name: J110 Load Cases
Designer: SLT Load Load Type Load Definition Live Load Description
C:\Users\sujeevanleonard.tham\OneDrive - AECOM\Projects\J110\J110\OneDrive_2021-07-01\12. Southern Case Deflection Case
Staircase\Design Files\Str\Slabs\Concourse Level RC Slab.rpf
List List Y/N A
1 Self Weight Applied Loads
RAPT - Version: 6.6.8.0
2 Extra Dead Load Applied Loads
Reinforced And Post-Tensioned Concrete Analysis & Design Package 3 Live Load Applied Loads Y
Copyright(C) 1988 - 2021 PCDC Pty. Ltd. All Rights Reserved
Licensee
1. Self Weight - Panel
AECOM Singapore Pte Ltd
Load Left End Left end of Load at Right Right end of Load at Description
300 Beach Road reference load from left end End load from right
#03-00 The Concourse column reference reference reference end
Singapore 199555 column column column
10479063400712WPN11 # mm kN/m2 # mm kN/m2 A
1 1 0 5 2 0 5
Due to the different Concrete Strength types in the Design Standard and Materials in this run, the concrete strengths shown in the materials data have been
multiplied in the calculatiuons by 0.8 Load Combinations : Short Term Service
Load Description 1. Self 2. Extra 3. Live
Span Combination Weight Dead Load Load
Span Span Slab Panel Panel A #.# #.# #.#
Length Depth Width Width 1 Live Load 1 1 0.5
Left Right
mm mm mm mm
LE 0
1 2000 200 1000 1000
Load Combinations : Permanent Service
Load Description 1. Self 2. Extra 3. Live
RE 0
Combination Weight Dead Load Load
A #.# #.# #.#
1 Live Load 1 1 0.3
Columns
Column Column Support Transverse Transverse
Grid Type Column prestress
Reference spacing (P/A) Load Combinations : Deflection
A List mm MPa Load Description 1. Self 2. Extra 3. Live
1 1 Knife-Edge 1000 Combination Weight Dead Load Load
A #.# #.# #.#
2 2 Knife-Edge 1000
1 Short Term - Deflection 1 1 0.5
2 Permanent - Deflection 1 1 0.3
3 Initial - Deflection 1 0 0
RAPT 6.6.8.0 Project Name: J110 Page 3/13 RAPT 6.6.8.0 Project Name: J110 Page 4/13
Licensee: AECOM Singapore Pte Ltd 1/6/2022 6:45:12 PM License No.: 10479063400712WPN11 Licensee: AECOM Singapore Pte Ltd 1/6/2022 6:45:15 PM License No.: 10479063400712WPN11
Load Combinations : Transfer Prestress Design Zones
Load Description 1. Self 2. Extra 3. Live Layer Steel Left End Distance to Bar stagger Top Right End Distance to Bar stagger Top Cover Maximum Minimum Preferred
Combination Weight Dead Load Load Number type Reference left end of length at left Cover at Reference right end of length at right at Right Bar Size Bar Size bar size
A #.# #.# #.# Column bar end left end Column bar end end
1 Transfer 1 0 0 List # mm mm mm # mm mm mm List List List
1 Bar 1 0 0 35 2 0 0 35 25 10 13
Design Zones
Load Combinations : Construction
Layer Steel Left End Distance to Bar stagger Bottom Right End Distance to Bar stagger Bottom Maximum Minimum Preferred
Load Description 1. Self 2. Extra 3. Live Number type Reference left end of length at left Cover at left Reference right end of length at right Cover at Bar Size Bar Size bar size
Combination Weight Dead Load Load Column bar end end Column bar end Right End
A #.# #.# #.# List # mm mm mm # mm mm mm List List List
1 Construction 1 0 0 1 Bar 1 0 0 35 2 0 0 35 25 10 13
Col No. 1 Characteristic Characteristic Service Service Ultimate Ultimate Ultimate Ultimate kN1 2
Service Service (Reversal) Flexure Flexure Shear Shear 24
(Reversal) (Reversal) (Reversal) 18 14.8
Elastic Axial Shortening mm 0 0 0 0 0 0 0 0 12
6
Col No. 2 Characteristic Characteristic Service Service Ultimate Ultimate Ultimate Ultimate 0
Service Service (Reversal) Flexure Flexure Shear Shear -6
(Reversal) (Reversal) (Reversal)
Moment Above kNm 0 0 0 0 0 0 0 0 -12
Moment Below kNm 0 0 0 0 0 0 0 0 -18 -14.8
Reaction kN 12.5 12.5 10 10 17.63 17.63 10.69 17.63 -24
0 2000mm
Elastic Rotation #.# -1.87e-4 -1.87e-4 -1.5e-4 -1.5e-4 -2.64e-4 -2.64e-4 -1.6e-4 -2.64e-4
Elastic Axial Shortening mm 0 0 0 0 0 0 0 0 Shear Shear 1 Shear 2
Flexural Design
Ultimate Design Ultimate
Flexure
1 2
mm2
1 2 1400 0
kNm 70
0 1.67 1.67 0
2 -70
-140
4 -210
6 -280
-350
8 347
-420
10 8.81 0 2000mm
0 2000mm
Reinforcement Top Total Bottom Total Top Ultimate Bottom Ultimate Min Top Min Bot
Moment Moment 1 Moment 2
kNm1 2
kN1 2 -4
24 0
18 14.8 4
12 8
6 12
0 16
-6 20
-12 24
-18 -14.8
0 2000mm
-24
0 2000mm
Capacity Minimum Ultimate Design Initial Final
Shear Shear 1 Shear 2
1 2
Shear 0.01
0
1 2 -0.01
kNm -0.02
0 -0.03
1.67 1.67 -0.04
2 -0.05
4 -0.06
-0.07
0.066
6
0 2000mm
8 6.94
10 Neutral Axis Depth Initial Final
0 2000mm
MPa1 2MPa
MPa
1 2
MPa
-1 -0.74 -3 -1.2 -0.92 -3.6
-0.8 -2.4 -0.9 -2.7
-0.6 -1.8
-0.4 -1.2 -0.6 -1.8
-0.2 -0.6 -0.3 -0.9
0 0 0 0
0.2 0.6 0.3 0.9
0.4 1.2 0.6 1.8
0.6 1.8
0.8 2.4 0.9 2.7
1 0.75 3 1.2 0.93 3.6
0 2000mm 0 2000mm
Gross Stress Top Gross Stress Bottom Cracked Compression Reinforcement Tension Gross Stress Top Gross Stress Bottom Cracked Compression Reinforcement Tension
MPa1 2MPa
MPa
1 2
MPa
-1 -0.74 -3 -1.2 -0.92 -3.6
-0.8 -2.4 -0.9 -2.7
-0.6 -1.8
-0.4 -1.2 -0.6 -1.8
-0.2 -0.6 -0.3 -0.9
0 0 0 0
0.2 0.6 0.3 0.9
0.4 1.2 0.6 1.8
0.6 1.8
0.8 2.4 0.9 2.7
1 0.75 3 1.2 0.93 3.6
0 2000mm 0 2000mm
Gross Stress Top Gross Stress Bottom Cracked Compression Reinforcement Tension Gross Stress Top Gross Stress Bottom Cracked Compression Reinforcement Tension
0 0 0 0 0 No shear steel
0 0 0 0 0 No shear steel
0 0 0 0 0 No shear steel
0 0 0 0 0 No shear steel
0 0 0 0 0 No shear steel
0 0 0 0 0 No shear steel
RAPT 6.6.8.0 Project Name: J110 Page 11/13 RAPT 6.6.8.0 Project Name: J110 Page 12/13
Licensee: 1/6/2022 6:45:38 PM License No.: 10479063400712WPN11 Licensee: AECOM Singapore Pte Ltd 1/6/2022 6:45:41 PM License No.: 10479063400712WPN11
Incremental
Spacing of Sets Minimum Legs Shear Comments
2 legs 4 legs 6 legs Min legs mm1 2
H10 H10 H10 H10 0
mm mm mm mm # A
0 0 0 0 0 No shear steel -0.4
0 0 0 0 0 No shear steel -0.5
0 0 0 0 0 No shear steel -0.8
0 0 0 0 0 No shear steel
0 0 0 0 0 No shear steel -1.2
0 0 0 0 0 No shear steel
0 0 0 0 0 No shear steel -1.6 4004
0 0 0 0 0 No shear steel 0 2000mm
0 0 0 0 0 No shear steel
0 0 0 0 0 No shear steel Total Long Term
0 0 0 0 0 No shear steel
mm1 2
0
-0.4
-0.577
Punching -0.8
Column Head Critical Section
Column Bh a at u d fcv P/A Asw/s min V* Mv* V*eff VRd1 VRd2 Asv result -1.2
No.
A #.# mm mm mm mm MPa MPa mm2/mm kN kNm kN kN kN mm2 A -1.6 3469
1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Check Not Carried Out! 0 2000mm
2 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Check Not Carried Out!
Detailed Reinforcement
Span 1
Top Reinforcement Bottom Reinforcement
Deflections
All Spans Loaded Max Max Section Max Max Section
Transfer Locat Size Space Area Depth Width Rebar Reqd Size Space Area Depth Width Rebar Reqd
mm mm mm mm2 mm mm A mm mm mm2 mm mm A
100 0 0 0 41.5 1000 No Steel Added 32 300 346.88 158.5 1000 5 H10 @ 226.3
mm1 2
0 160 0 0 0 41.5 1000 No Steel Added 32 300 346.88 158.5 1000 5 H10 @ 226.3
228 0 0 0 41.5 1000 No Steel Added 32 300 346.88 158.5 1000 5 H10 @ 226.3
-0.081
-0.4 296 0 0 0 41.5 1000 No Steel Added 32 300 346.88 158.5 1000 5 H10 @ 226.3
364 0 0 0 41.5 1000 No Steel Added 32 300 346.88 158.5 1000 5 H10 @ 226.3
-0.8 432 0 0 0 41.5 1000 No Steel Added 32 300 346.88 158.5 1000 5 H10 @ 226.3
500 0 0 0 41.5 1000 No Steel Added 32 300 346.88 158.5 1000 5 H10 @ 226.3
-1.2 666 0 0 0 41.5 1000 No Steel Added 32 300 346.88 158.5 1000 5 H10 @ 226.3
832 0 0 0 41.5 1000 No Steel Added 32 300 346.88 158.5 1000 5 H10 @ 226.3
-1.6 24674 1000 0 0 0 41.5 1000 No Steel Added 32 300 346.88 158.5 1000 5 H10 @ 226.3
0 2000mm 1168 0 0 0 41.5 1000 No Steel Added 32 300 346.88 158.5 1000 5 H10 @ 226.3
1334 0 0 0 41.5 1000 No Steel Added 32 300 346.88 158.5 1000 5 H10 @ 226.3
Short Term 1500 0 0 0 41.5 1000 No Steel Added 32 300 346.88 158.5 1000 5 H10 @ 226.3
1568 0 0 0 41.5 1000 No Steel Added 32 300 346.88 158.5 1000 5 H10 @ 226.3
mm1 2 1636 0 0 0 41.5 1000 No Steel Added 32 300 346.88 158.5 1000 5 H10 @ 226.3
0 1704 0 0 0 41.5 1000 No Steel Added 32 300 346.88 158.5 1000 5 H10 @ 226.3
1772 0 0 0 41.5 1000 No Steel Added 32 300 346.88 158.5 1000 5 H10 @ 226.3
-0.154
-0.4 1840 0 0 0 41.5 1000 No Steel Added 32 300 346.88 158.5 1000 5 H10 @ 226.3
1900 0 0 0 41.5 1000 No Steel Added 32 300 346.88 158.5 1000 5 H10 @ 226.3
-0.8 Shear Reinforcement
Spacing of Sets
-1.2 2 legs 4 legs 6 legs Min legs Minimum Shear
Area H10 H10 H10 H10 Legs Comments
-1.6 12969 mm2/mm mm mm mm mm # A
0 2000mm
0 0 0 0 0 0 No shear steel
0 0 0 0 0 0 No shear steel
0 0 0 0 0 0 No shear steel
0 0 0 0 0 0 No shear steel
0 0 0 0 0 0 No shear steel
0 0 0 0 0 0 No shear steel
0 0 0 0 0 0 No shear steel
0 0 0 0 0 0 No shear steel
0 0 0 0 0 0 No shear steel
0 0 0 0 0 0 No shear steel
0 0 0 0 0 0 No shear steel
RAPT 6.6.8.0 Project Name: J110 Page 13/13
Licensee: AECOM Singapore Pte Ltd 1/6/2022 6:45:44 PM License No.: 10479063400712WPN11
Shear Reinforcement
Spacing of Sets
2 legs 4 legs 6 legs Min legs Minimum Shear
Area H10 H10 H10 H10 Legs Comments
mm2/mm mm mm mm mm # A
0 0 0 0 0 0 No shear steel
0 0 0 0 0 0 No shear steel
0 0 0 0 0 0 No shear steel
0 0 0 0 0 0 No shear steel
0 0 0 0 0 0 No shear steel
0 0 0 0 0 0 No shear steel
Design Comments:-
- - Span 1 - Required Bar Size is smaller than the Preferred Bar Size. Maintaining the same cover will require slightly less reinforcement than calculated.
- Span - 1 - Reinforcement added at left span contraflexure point for Offset of Bending Moment Diagram for Shear - 50.62mm2
- Span - 1 - Reinforcement added at right span contraflexure point for Offset of Bending Moment Diagram for Shear - 50.62mm2
Reinforcement Layout
1 2
mm
0
-50
-100
-150
5-H10
-200
0 2000mm
Flat slabs - slabs which rely on flexural action through the slab or slab thickenings such as drop panels or band beams to discrete column supports, require
concentration of the top reinforcement and tendons over supports within a defined width from the column face to facilitate moment transfer to the column. This
width varies and the amount of reinforcement varies for different design codes. In the major codes, the requirements are specified in AS3600 cl 9.1.2,
Eurocode 1992 - 1 - 1 2004 cl 9.4.1, ACI318-14 cl 8.4.2.3 and BS8110 cl3.7.3.1. For example AS3600 requires that 25% of total negative moment for the
entire slab panel be resisted by reinforcement within a width D either side of the column. RAPT cannot define this concentration as it does not know the
transverse spacing of the tendons. It is the designer's responsibility to ensure that these clauses are complied with.
- - Span 1 - Required Bar Size is smaller than the Preferred Bar Size. Maintaining the same cover will require slightly less reinforcement than calculated.
- Span - 1 - Reinforcement added at left span contraflexure point for Offset of Bending Moment Diagram for Shear - 50.62mm2
- Span - 1 - Reinforcement added at right span contraflexure point for Offset of Bending Moment Diagram for Shear - 50.62mm2
RAPT 6.6.8.0 Project Name: J110 Page 2/13
Licensee: AECOM Singapore Pte Ltd 1/6/2022 7:10:06 PM License No.: 10479063400712WPN11
Frame Description: PRECAST PALNK
Project Name: J110 Load Cases
Frame Description: PRECAST PALNK Load Load Type Load Definition Live Load Description
Designer: SLT Case Deflection Case
C:\Users\sujeevanleonard.tham\OneDrive - AECOM\Projects\J110\J110\OneDrive_2021-07-01\12. Southern
List List Y/N A
Staircase\Design Files\Str\Slabs\Precast plank at Concourse level.rpf
1 Self Weight Applied Loads
2 Extra Dead Load Applied Loads
RAPT - Version: 6.6.8.0 3 Live Load Applied Loads Y
Reinforced And Post-Tensioned Concrete Analysis & Design Package
Copyright(C) 1988 - 2021 PCDC Pty. Ltd. All Rights Reserved
1. Self Weight - Panel
Licensee Load Left End Left end of Load at Right Right end of Load at Description
AECOM Singapore Pte Ltd reference load from left end End load from right
300 Beach Road column reference reference reference end
#03-00 The Concourse column column column
Singapore 199555 # mm kN/m2 # mm kN/m2 A
10479063400712WPN11 1 1 0 3 2 0 3
Due to the different Concrete Strength types in the Design Standard and Materials in this run, the concrete strengths shown in the materials data have been Load Combinations : Short Term Service
multiplied in the calculatiuons by 0.8 Load Description 1. Self 2. Extra 3. Live
Combination Weight Dead Load Load
Span A #.# #.# #.#
Span Span Slab Panel Panel 1 Live Load 1 1 0.5
Length Depth Width Width
Left Right
mm mm mm mm
Load Combinations : Permanent Service
LE 0
Load Description 1. Self 2. Extra 3. Live
1 2000 120 1000 1000
Combination Weight Dead Load Load
RE 0 A #.# #.# #.#
1 Live Load 1 1 0.3
Columns
Column Column Support Transverse Transverse Load Combinations : Deflection
Grid Type Column prestress
Load Description 1. Self 2. Extra 3. Live
Reference spacing (P/A)
Combination Weight Dead Load Load
A List mm MPa
A #.# #.# #.#
1 1 Knife-Edge 1000
1 Short Term - Deflection 1 1 0.5
2 2 Knife-Edge 1000
2 Permanent - Deflection 1 1 0.3
3 Initial - Deflection 1 0 0
RAPT 6.6.8.0 Project Name: J110 Page 3/13 RAPT 6.6.8.0 Project Name: J110 Page 4/13
Licensee: AECOM Singapore Pte Ltd 1/6/2022 7:10:09 PM License No.: 10479063400712WPN11 Licensee: AECOM Singapore Pte Ltd 1/6/2022 7:10:12 PM License No.: 10479063400712WPN11
Frame Description: PRECAST PALNK Frame Description: PRECAST PALNK
Load Combinations : Transfer Prestress Design Zones
Load Description 1. Self 2. Extra 3. Live Layer Steel Left End Distance to Bar stagger Top Right End Distance to Bar stagger Top Cover Maximum Minimum Preferred
Combination Weight Dead Load Load Number type Reference left end of length at left Cover at Reference right end of length at right at Right Bar Size Bar Size bar size
A #.# #.# #.# Column bar end left end Column bar end end
1 Transfer 1 0 0 List # mm mm mm # mm mm mm List List List
1 Bar 1 0 0 35 2 0 0 35 25 10 13
Design Zones
Load Combinations : Construction
Layer Steel Left End Distance to Bar stagger Bottom Right End Distance to Bar stagger Bottom Maximum Minimum Preferred
Load Description 1. Self 2. Extra 3. Live Number type Reference left end of length at left Cover at left Reference right end of length at right Cover at Bar Size Bar Size bar size
Combination Weight Dead Load Load Column bar end end Column bar end Right End
A #.# #.# #.# List # mm mm mm # mm mm mm List List List
1 Construction 1 0 0 1 Bar 1 0 0 35 2 0 0 35 25 10 13
Concrete Tensile Strength for Deflection Calculations- #.## x (Fc)n #.# -1 -60
Maximum Value of Ieff/Igross for Deflection Calculations #.# 0.6
Total Deflection Warning Limit - Maximum Span/Deflection #.# 250 -90
Total Deflection Warning Limit - Maximum Deflection mm 25
Incremental Deflection Warning Limit - Maximum Span/Deflection #.# 500 -120
Incremental Deflection Warning Limit - Maximum Deflection mm 25 0 2000mm
Initial Time for Shrinkage List Full Shrinkage
Time of Loading in days #.# 10 Plan view
Age Adjustment Factor #.# 0.76
1 2
Concrete Strength at Time of Loading MPa 27.04
mm
Loaded Period in years #.# 30 -400
Tension stiffening Approach List Modified Concrete Tensile Modulus Method
-200
Live Load Pattern Factor #.#
Pattern Live Load for Ultimate Strength Y/N 0
Pattern Live Load for Crack Control Y/N 200
Pattern Live Load For Deflections Y/N
Pattern Live Load for Deflection Permanent Load Combination Y/N 400
0 2000mm
Material Properties Warnings
Concrete : Standard Concrete : Concrete Strength Basis - Cube Input
Description A C32/40MPa No errors or warnings were found.
Characteristic Compressive Strength MPa 40
Mean Compressive Strength MPa 50
Output
Lower Characteristic Tensile Strength MPa 2.12
Warning:SPAN Reinforcing Bar spacing There have been problems in determining a bar size to satisfy the design spacing requirements. See Detailed
Upper Characteristic Tensile Strength MPa 3.93 Reinforcement Design Comments.
Concrete Density kg/m3 2447 Warning:Flat slabs - slabs which rely on flexural action through the slab or slab thickenings such as drop panels or band beams to discrete column
Design Concrete Modulus MPa 31186.6 supports, require concentration of the top reinforcement and tendons over supports within a defined width from the column face to facilitate moment
Mean Concrete Modulus MPa 33345.8 transfer to the column. This width varies and the amount of reinforcement varies for different design codes. In the major codes, the requirements are
Basic Shrinkage Strain mm/mm 0 specified in AS3600 cl 9.1.2, Eurocode 1992 - 1 - 1 2004 cl 9.4.1, ACI318-14 cl 8.4.2.3 and BS8110 cl3.7.3.1. For example AS3600 requires that 25% of
Shrinkage Multiplier #.# 1 total negative moment for the entire slab panel be resisted by reinforcement within a width D either side of the column. RAPT cannot define this
#.# concentration as it does not know the transverse spacing of the tendons. It is the designer's responsibility to ensure that these clauses are complied with.
Basic Creep Factor 2.656
Creep Multiplier #.# 1
Concrete Strain at Peak Stress #.# 0.002
Squash Load Factor #.# 0.85
Concrete Strain Limit #.# 0.004 Bending Moments
Strength Gain Rate List Normal Load Cases
Maximum Aggregate Size mm 20
Column Actions
Col No. 1 Self Extra Dead Live
Weight Load Load
Reinforcement Bar Moment Above kNm -0 -0 -0
Designation Type Yield Elastic Ductility Peak Peak Design Material Material Material Capacity Material Capacity Include as Description Moment Below kNm -0 -0 -0
Stress Modulus Strain Stress Strain Factor Factor Reduction Factor Reduction Factor Flexural Reaction kN 3 2.5 5
Limit Flexure Shear - Flexure - Shear Reinforcement for Elastic Rotation #.# 2.08e-4 1.74e-4 3.47e-4
Shear Elastic Axial Shortening mm 0 0 0
H Deformed 500 2.05e5 N 0.05 540 90 -1 -1 -1 -1 Y
Col No. 2 Self Extra Live Load
Weight Dead
Nominal Bar Bar Area Bar Bar Stock Load
Bar Size Diameter Inertia Weight Length Moment Above kNm -0 -0 -0
A mm mm2 mm4 kg/m mm Moment Below kNm -0 -0 -0
10 10 78.5 491.07 0.62 12000 Reaction kN 3 2.5 5
13 13 132.7 1402.55 1.04 12000 Elastic Rotation #.# -2.08e-4 -1.74e-4 -3.47e-4
16 16 201.1 3218.29 1.58 12000 Elastic Axial Shortening mm 0 0 0
20 20 314.2 7857.14 2.47 12000
22 22 380.1 11503.6 2.98 12000
25 25 490.9 19182.5 3.85 12000
32 32 804.2 51492.6 6.31 12000 Load Combinations
40 40 1256.6 1.257e5 9.86 12000 Column Actions
Col No. 1 Characteristic Characteristic Service Service Ultimate Ultimate Ultimate Ultimate
Service Service (Reversal) Flexure Flexure Shear Shear
(Reversal) (Reversal) (Reversal)
Moment Above kNm 0 0 0 0 0 0 0 0
RAPT 6.6.8.0 Project Name: J110 Page 7/13 RAPT 6.6.8.0 Project Name: J110 Page 8/13
Licensee: AECOM Singapore Pte Ltd 1/6/2022 7:10:21 PM License No.: 10479063400712WPN11 Licensee: AECOM Singapore Pte Ltd 1/6/2022 7:10:24 PM License No.: 10479063400712WPN11
Frame Description: PRECAST PALNK Frame Description: PRECAST PALNK
Col No. 1 Characteristic Characteristic Service Service Ultimate Ultimate Ultimate Ultimate kN1 2
Service Service (Reversal) Flexure Flexure Shear Shear 20
(Reversal) (Reversal) (Reversal) 13.4
15
Moment Below kNm 0 0 0 0 0 0 0 0 10
Reaction kN 10.5 10.5 8 8 14.93 14.93 7.84 14.93 5
Elastic Rotation #.# 7.29e-4 7.29e-4 5.55e-4 5.55e-4 1.04e-3 1.04e-3 5.44e-4 1.04e-3 0
Elastic Axial Shortening mm 0 0 0 0 0 0 0 0 -5
-10
Col No. 2 Characteristic Characteristic Service Service Ultimate Ultimate Ultimate Ultimate -15
Service Service (Reversal) Flexure Flexure Shear Shear -13.4
-20
(Reversal) (Reversal) (Reversal) 0 2000mm
Moment Above kNm 0 0 0 0 0 0 0 0
Moment Below kNm 0 0 0 0 0 0 0 0 Shear Shear 1 Shear 2
Reaction kN 10.5 10.5 8 8 14.93 14.93 7.84 14.93
Elastic Rotation #.# -7.29e-4 -7.29e-4 -5.55e-4 -5.55e-4 -1.04e-3 -1.04e-3 -5.44e-4 -1.04e-3
Elastic Axial Shortening mm 0 0 0 0 0 0 0 0 Flexural Design
Ultimate
1 2
mm2
Ultimate Design 1000 0
Flexure 50
0
1 2 -50
kNm
-1 -100
0 1.42 1.42 -150
1 -200
2 -250
3 255
4 -300
5 0 2000mm
6
7 Reinforcement Top Total Bottom Total Top Ultimate Bottom Ultimate Min Top Min Bot
8 7.46
0 2000mm 1 2
kNm
Moment Moment 1 Moment 2 -1
0
1
2
kN1 2 3
20 4
13.4 5
15 6
10 7
5 8
9
0 10
-5 0 2000mm
-10
Capacity Minimum Ultimate Design Initial Final
-15
-13.4
-20
0 2000mm 1 2
Shear Shear 1 Shear 2
0
-0.02
Shear
-0.04
1 2 -0.06
kNm
-1 -0.08
0 1.42 1.42 -0.1
0.095
1
2 0 2000mm
3
4
5 Neutral Axis Depth Initial Final
6
5.59
7
8
0 2000mm
Gross Stress Top Gross Stress Bottom Cracked Compression Reinforcement Tension Gross Stress Top Gross Stress Bottom Cracked Compression Reinforcement Tension
Gross Stress Top Gross Stress Bottom Cracked Compression Reinforcement Tension Gross Stress Top Gross Stress Bottom Cracked Compression Reinforcement Tension
Design Comments:-
- SPAN Reinforcing Bar spacing - Span 1 - Smallest preferred reinforcement size requires bar spacing larger than maximum. It will be necessary to use
smaller bars than the preferred minimum size or a larger area of reinforcement than is required by design.
- - Span 1 - Required Bar Size is smaller than the Preferred Bar Size. Maintaining the same cover will require slightly less reinforcement than calculated.
- Span - 1 - Reinforcement added at left span contraflexure point for Offset of Bending Moment Diagram for Shear - 42.87mm2
- Span - 1 - Reinforcement added at right span contraflexure point for Offset of Bending Moment Diagram for Shear - 42.87mm2
Reinforcement Layout
1 2
mm
0
-30
-60
4-H10
-90
-120
0 2000mm
Flat slabs - slabs which rely on flexural action through the slab or slab thickenings such as drop panels or band beams to discrete column supports, require
concentration of the top reinforcement and tendons over supports within a defined width from the column face to facilitate moment transfer to the column. This
width varies and the amount of reinforcement varies for different design codes. In the major codes, the requirements are specified in AS3600 cl 9.1.2,
Eurocode 1992 - 1 - 1 2004 cl 9.4.1, ACI318-14 cl 8.4.2.3 and BS8110 cl3.7.3.1. For example AS3600 requires that 25% of total negative moment for the
entire slab panel be resisted by reinforcement within a width D either side of the column. RAPT cannot define this concentration as it does not know the
transverse spacing of the tendons. It is the designer's responsibility to ensure that these clauses are complied with.
- SPAN Reinforcing Bar spacing - Span 1 - Smallest preferred reinforcement size requires bar spacing larger than maximum. It will be necessary to use
smaller bars than the preferred minimum size or a larger area of reinforcement than is required by design.
- - Span 1 - Required Bar Size is smaller than the Preferred Bar Size. Maintaining the same cover will require slightly less reinforcement than calculated.
- Span - 1 - Reinforcement added at left span contraflexure point for Offset of Bending Moment Diagram for Shear - 42.87mm2
- Span - 1 - Reinforcement added at right span contraflexure point for Offset of Bending Moment Diagram for Shear - 42.87mm2
C:\Users\sujeevanleonard.tham\OneDrive - AECOM\Projects\J110\J110\OneDrive_2021-07-01\12. Southern
Staircase\Design Files\Str\Slabs\Lower platform RC Sla (Cantilever).rpf
Licensee
AECOM Singapore Pte Ltd
300 Beach Road
#03-00 The Concourse
Singapore 199555
10479063400712WPN11
Input
General
Design Code List Singapore - Eurocode 2*SAVED*
Material List Singapore - Singapore Eurocode Materials*SAVED*
Reinforcement Type List Reinforced
Member Type List Slab
Panel Type List Internal
Strip Type List One way - Full Width
Column Stiffness List Equivalent Column
Concrete Type List Standard Concrete
Concrete - Spanning Members List C32/40MPa
Concrete - Columns List C32/40MPa
Top Reinforcement Cover mm 35
Bottom Reinforcement Cover mm 35
Top Reinforcement Axis Depth Limit mm 20
Bottom Reinforcement Axis Depth Limit mm 20
Concrete Unit Weight kn/m3 25
Self Weight Definition List Program Calculated
Pattern Live Load Y/N
Earthquake Design List None
Moment Redistribution % 0
Design Surface Levels List Extreme Surfaces
Eurocode Ultimate Load Combination Basis List Eurocode Eqn 6.10
Due to the different Concrete Strength types in the Design Standard and Materials in this run, the concrete strengths shown in the materials data have been
multiplied in the calculatiuons by 0.8
Span
Span Span Slab Panel Panel
Length Depth Width Width
Left Right
mm mm mm mm
LE 0
RC 3000 250 1000 1000
Columns
Column Column Support Column Column Column Column Column Column Transverse Capital Depth Pin Percentage Braced Column
Grid Type Height Width Length Height Width Length Column below deepest Base Column frame at this Shortening
Reference Above Above Above below below below spacing section below Stiffness column Restrained
A List mm mm mm mm mm mm mm mm Y/N % Y/N Y/N
1 1 Column 3000 1000 250 3000 1000 250 1000 0 Y 100 Y N
1
kN/m P1
6
4
2
0
0mm
1
kN/m
6 P1
4
2
0
0mm
Reinforcement
Reinforcement Reinforcement Preferred Number
Use Type Bar Size of Legs
List List #
Flexural Bar H 500MPa
Flexural Mesh A 500MPa
Shear Option 1 H 500MPa 10 2
Shear Option 2 H 500MPa 10 4
Shear Option 3 H 500MPa 10 6
Punching Shear H 500MPa 10 2
Reinforcement
Maximum Minimum Minimum Minimum Span Minimum Span Infill Stagger
Bar Bar Continuous Reinforcement Reinforcement Bars Bars
Spacing Spacing Reinforcement into End into Internal
Support Support
mm mm #.# #.# #.# Y/N Y/N
Support Reinforcement 300 99 0 N N
Span Reinforcement 300 99 0 0 N N
RAPT 6.6.8.0 1/6/2022 6:42:26 PM Page 4/13
Licensee: AECOM Singapore Pte Ltd License No.: 10479063400712WPN11
Design Zones
Layer Steel Left End Distance to Bar stagger Top Right End Distance to Bar stagger Top Cover Maximum Minimum Preferred
Number type Reference left end of length at left Cover at Reference right end of length at right at Right Bar Size Bar Size bar size
Column bar end left end Column bar end end
List # mm mm mm # mm mm mm List List List
1 Bar 1 0 0 35 2 0 0 35 25 10 13
Design Zones
Layer Steel Left End Distance to Bar stagger Bottom Right End Distance to Bar stagger Bottom Maximum Minimum Preferred
Number type Reference left end of length at left Cover at left Reference right end of length at right Cover at Bar Size Bar Size bar size
Column bar end end Column bar end Right End
List # mm mm mm # mm mm mm List List List
1 Bar 1 0 0 35 2 0 0 35 25 10 13
User Defined
Layer Steel type Left End Distance Bar Top % Development % Development Right End Distance Bar Top % Development
Number Reference to left stagger Cover of Left End of of Left End of Bar Reference to right stagger Cover of Right End of
Column end of length at at left Bar in Tension in Compression Column end of length at at Right Bar in Tension
bar left end end bar right end end
List # mm mm mm % % # mm mm mm %
1 H 500MPa 1 0 0 35 100 100 1 3000 0 35 100
User Defined
Layer Steel type Left End Distance Bar Bottom % Development % Development Right End Distance Bar Bottom % Development
Number Reference to left stagger Cover of Left End of of Left End of Bar Reference to right stagger Cover of Right End of
Column end of length at at Left Bar in Tension in Compression Column end of length at at Right Bar in Tension
bar left end end bar right end End
List # mm mm mm % % # mm mm mm %
1 H 500MPa 1 0 0 35 100 100 1 3000 0 35 100
1
mm
0
-70
-140
-210
-280
0mm
1
mm
0
-70
-140
-210
-280
0mm
Design Data
Capacity Reduction factor (phi) for Flexure #.# 1
Capacity Reduction factor (phi) for Shear #.# 1
Capacity Reduction factor (phi) for Shear with transverse reinf #.# 1
Material Factor for Concrete in Flexure #.# 1.5
Material Factor for Concrete in Shear #.# 1.5
Material Factor for Reinforcement #.# 1.15
Maximum Ratio of Neutral Axis Depth for Ductility #.# 0.58
Ductility Limit - Strain #.# 0
Ductility Check at Left End Column Y/N Y
Ductility Check at Right End Column Y/N Y
Minimum Reinforcement Strength Limit - #.## x M* #.# 0
Flexural Critical Section - Consider Transverse Beams Y/N Y
Flexural Critical Section - Distance from centre of Support #.# -1
Beam Left Sideface Cover (Internal) mm 25
Beam Right Sideface cover mm 40
Prestress Minimum Reinforcement Basis List Program Default
Shear Enhancement at Supports Y/N N
Ast Value in Shear Calculations List Calculated
Limit Reinforcement Strain Y/N Y
Include Strain Hardening of Reinforcement Y/N N
Beam Shear Critical Section Location List Code Critical Section
Material Properties
Concrete : Standard Concrete : Concrete Strength Basis - Cube
Description A C32/40MPa
Characteristic Compressive Strength MPa 40
Mean Compressive Strength MPa 50
Lower Characteristic Tensile Strength MPa 2.12
Upper Characteristic Tensile Strength MPa 3.93
Concrete Density kg/m3 2447
Design Concrete Modulus MPa 31186.6
Mean Concrete Modulus MPa 33345.8
Basic Shrinkage Strain mm/mm 0
Shrinkage Multiplier #.# 1
Basic Creep Factor #.# 2.656
Creep Multiplier #.# 1
Concrete Strain at Peak Stress #.# 0.002
Squash Load Factor #.# 0.85
Concrete Strain Limit #.# 0.004
Strength Gain Rate List Normal
Maximum Aggregate Size mm 20
Reinforcement Bar
Designation Type Yield Elastic Ductility Peak Peak Design Material Material Material Capacity Material Capacity Include as Description
Stress Modulus Strain Stress Strain Factor Factor Reduction Factor Reduction Factor Flexural
Limit Flexure Shear - Flexure - Shear Reinforcement for
Shear
H Deformed 500 2.05e5 N 0.05 540 90 -1 -1 -1 -1 Y
Elevation view
1
mm
0
-70
-140
-210
-280
0mm
RAPT 6.6.8.0 1/6/2022 6:42:35 PM Page 7/13
Licensee: AECOM Singapore Pte Ltd License No.: 10479063400712WPN11
Plan view
1
mm
-400
-200
200
400
0mm
mm
2000
-2000
0mm
Warnings
Input
No errors or warnings were found.
Output
Warning:The deflections reported for cantilevers without backspans do not allow for the rotation of the column. The designer needs to add a component of
deflection for this that includes the effects of cracking and long term effects on the rotation of the column.
Warning:Flat slabs - slabs which rely on flexural action through the slab or slab thickenings such as drop panels or band beams to discrete column
supports, require concentration of the top reinforcement and tendons over supports within a defined width from the column face to facilitate moment
transfer to the column. This width varies and the amount of reinforcement varies for different design codes. In the major codes, the requirements are
specified in AS3600 cl 9.1.2, Eurocode 1992 - 1 - 1 2004 cl 9.4.1, ACI318-14 cl 8.4.2.3 and BS8110 cl3.7.3.1. For example AS3600 requires that 25% of
total negative moment for the entire slab panel be resisted by reinforcement within a width D either side of the column. RAPT cannot define this
concentration as it does not know the transverse spacing of the tendons. It is the designer's responsibility to ensure that these clauses are complied with.
Bending Moments
Load Cases
Column Actions
Col No. 1 Self Extra Dead Live
Weight Load Load
Moment Above kNm 15.73 6.29 12.58
Moment Below kNm 12.4 4.96 9.92
Reaction kN 18.75 7.5 15
Elastic Rotation #.# 0 0 0
Elastic Axial Shortening mm 0 0 0
Load Combinations
Column Actions
Col No. 1 Characteristic Characteristic Service Service Ultimate Ultimate Ultimate Ultimate
Service Service (Reversal) Flexure Flexure Shear Shear
(Reversal) (Reversal) (Reversal)
Moment Above kNm 34.6 34.6 28.31 28.31 31.37 48.59 31.37 48.59
Moment Below kNm 27.28 27.28 22.32 22.32 24.74 38.32 24.74 38.32
Reaction kN 41.25 41.25 33.75 33.75 37.41 57.94 37.41 57.94
Elastic Rotation #.# 0 0 0 0 0 0 0 0
Elastic Axial Shortening mm 0 0 0 0 0 0 0 0
RAPT 6.6.8.0 1/6/2022 6:42:39 PM Page 8/13
Licensee: AECOM Singapore Pte Ltd License No.: 10479063400712WPN11
Ultimate Design
Flexure
1
kNm
-100
-79.8
-80
-60
-40
-20
0
0mm
1
kN
60 51.7
50
40
30
20
10
0
-10
0mm
Shear
1
kNm
-100
-79.8
-80
-60
-40
-20
0
0mm
1
kN
60 51.7
50
40
30
20
10
0
-10
0mm
mm21
100
0
80
60
40
20
0
-20
-40
-60
-80
0
-100
0mm
Reinforcement Top Total Bottom Total Top Ultimate Bottom Ultimate Min Top Min Bot
1
kNm
-120
-100
-80
-60
-40
-20
0
20
0mm
1
0.19
0.21
0.18
0.15
0.12
0.09
0.06
0.03
0
-0.03
0mm
Service
Maximum Moment Condition
1
MPa MPa
-6 -4.14 -210
-4 -140
-2 -70
0 0
2 70
4 140
6 210
8 280
10 4.14 350
0mm
Gross Stress Top Gross Stress Bottom Cracked Compression Reinforcement Tension Limits
RAPT 6.6.8.0 1/6/2022 6:42:45 PM Page 10/13
Licensee: AECOM Singapore Pte Ltd License No.: 10479063400712WPN11
Reversal Moment Condition
1
MPa MPa
-6 -4.14 -210
-4 -140
-2 -70
0 0
2 70
4 140
6 210
8 280
10 4.14 350
0mm
Gross Stress Top Gross Stress Bottom Cracked Compression Reinforcement Tension Limits
Permanent
Maximum Moment Condition
MPa1 MPa
-6 -210
-3.77
-4 -140
-2 -70
0 0
2 70
4 140
6 210
8 280
3.77
10 350
0mm
Gross Stress Top Gross Stress Bottom Cracked Compression Reinforcement Tension Limits
MPa1 MPa
-6 -210
-3.77
-4 -140
-2 -70
0 0
2 70
4 140
6 210
8 280
3.77
10 350
0mm
Gross Stress Top Gross Stress Bottom Cracked Compression Reinforcement Tension Limits
Characteristic Service
Maximum Moment Condition
1
MPa MPa
-5.06
-6 -200
-3 -100
0 0
3 100
6 200
9 300
12 5.06 400
0mm
Gross Stress Top Gross Stress Bottom Cracked Compression Reinforcement Tension Limits
RAPT 6.6.8.0 1/6/2022 6:42:49 PM Page 11/13
Licensee: AECOM Singapore Pte Ltd License No.: 10479063400712WPN11
Reversal Moment Condition
1
MPa MPa
-5.06
-6 -200
-3 -100
0 0
3 100
6 200
9 300
12 5.06 400
0mm
Gross Stress Top Gross Stress Bottom Cracked Compression Reinforcement Tension Limits
Shear Design
Beam
Span 1
Locat V* Mv* Pv Mdec d Ast bv phi Vuc phi Vut phi Vu Phi Vumax phi VuMin phi Vus Theta Asv/s
0 0 0 0 0 No shear steel
0 0 0 0 0 No shear steel
0 0 0 0 0 No shear steel
0 0 0 0 0 No shear steel
0 0 0 0 0 No shear steel
0 0 0 0 0 No shear steel
0 0 0 0 0 No shear steel
0 0 0 0 0 No shear steel
0 0 0 0 0 No shear steel
0 0 0 0 0 No shear steel
0 0 0 0 0 No shear steel
0 0 0 0 0 No shear steel
0 0 0 0 0 No shear steel
0 0 0 0 0 No shear steel
0 0 0 0 0 No shear steel
Punching
Column Head Critical Section
Column Bh a at u d fcv P/A Asw/s min V* Mv* V*eff VRd1 VRd2 Asv result
No.
A #.# mm mm mm mm MPa MPa mm2/mm kN kNm kN kN kN mm2 A
1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Check failed, d = 0
RAPT 6.6.8.0 1/6/2022 6:42:52 PM Page 12/13
Licensee: AECOM Singapore Pte Ltd License No.: 10479063400712WPN11
Deflections
All Spans Loaded
Transfer
mm1
0
-2.35
-10
-20
-30
-40
1276
0mm
Short Term
mm1
0
-10 -6.65
-20
-30
-40
451
0mm
Incremental
mm1
0
-10
-12.8
-20
-30
-40
235
0mm
mm1
0
-10
-20 -15
-30
-40
200
0mm
Detailed Reinforcement
Span 1
Top Reinforcement Bottom Reinforcement
0 0 0 0 0 0 No shear steel
0 0 0 0 0 0 No shear steel
0 0 0 0 0 0 No shear steel
0 0 0 0 0 0 No shear steel
0 0 0 0 0 0 No shear steel
0 0 0 0 0 0 No shear steel
0 0 0 0 0 0 No shear steel
0 0 0 0 0 0 No shear steel
0 0 0 0 0 0 No shear steel
0 0 0 0 0 0 No shear steel
0 0 0 0 0 0 No shear steel
0 0 0 0 0 0 No shear steel
0 0 0 0 0 0 No shear steel
0 0 0 0 0 0 No shear steel
0 0 0 0 0 0 No shear steel
Reinforcement Layout
(H16@150)
1
mm
0
-70
-140
-210
(H16@150)
-280
0mm
RAPT 6.6.8.0 Project Name: J110 Page 2/13
Licensee: AECOM Singapore Pte Ltd 1/6/2022 6:50:33 PM License No.: 10479063400712WPN11
Project Name: J110 Load Cases
Designer: SLT Load Load Type Load Definition Live Load Description
C:\Users\sujeevanleonard.tham\OneDrive - AECOM\Projects\J110\J110\OneDrive_2021-07-01\12. Southern Case Deflection Case
Staircase\Design Files\Str\Slabs\Lower platform RC Slab.rpf
List List Y/N A
1 Self Weight Applied Loads
RAPT - Version: 6.6.8.0
2 Extra Dead Load Applied Loads
Reinforced And Post-Tensioned Concrete Analysis & Design Package 3 Live Load Applied Loads Y
Copyright(C) 1988 - 2021 PCDC Pty. Ltd. All Rights Reserved
Licensee
1. Self Weight - Panel
AECOM Singapore Pte Ltd
Load Left End Left end of Load at Right Right end of Load at Description
300 Beach Road reference load from left end End load from right
#03-00 The Concourse column reference reference reference end
Singapore 199555 column column column
10479063400712WPN11 # mm kN/m2 # mm kN/m2 A
1 1 0 5 2 0 5
Due to the different Concrete Strength types in the Design Standard and Materials in this run, the concrete strengths shown in the materials data have been
multiplied in the calculatiuons by 0.8 Load Combinations : Short Term Service
Load Description 1. Self 2. Extra 3. Live
Span Combination Weight Dead Load Load
Span Span Slab Panel Panel A #.# #.# #.#
Length Depth Width Width 1 Live Load 1 1 0.5
Left Right
mm mm mm mm
LE 0
1 3000 200 1000 1000
Load Combinations : Permanent Service
Load Description 1. Self 2. Extra 3. Live
RE 0
Combination Weight Dead Load Load
A #.# #.# #.#
1 Live Load 1 1 0.3
Columns
Column Column Support Transverse Transverse
Grid Type Column prestress
Reference spacing (P/A) Load Combinations : Deflection
A List mm MPa Load Description 1. Self 2. Extra 3. Live
1 1 Knife-Edge 1000 Combination Weight Dead Load Load
A #.# #.# #.#
2 2 Knife-Edge 1000
1 Short Term - Deflection 1 1 0.5
2 Permanent - Deflection 1 1 0.3
3 Initial - Deflection 1 0 0
RAPT 6.6.8.0 Project Name: J110 Page 3/13 RAPT 6.6.8.0 Project Name: J110 Page 4/13
Licensee: AECOM Singapore Pte Ltd 1/6/2022 6:50:36 PM License No.: 10479063400712WPN11 Licensee: AECOM Singapore Pte Ltd 1/6/2022 6:50:39 PM License No.: 10479063400712WPN11
Load Combinations : Transfer Prestress Design Zones
Load Description 1. Self 2. Extra 3. Live Layer Steel Left End Distance to Bar stagger Top Right End Distance to Bar stagger Top Cover Maximum Minimum Preferred
Combination Weight Dead Load Load Number type Reference left end of length at left Cover at Reference right end of length at right at Right Bar Size Bar Size bar size
A #.# #.# #.# Column bar end left end Column bar end end
1 Transfer 1 0 0 List # mm mm mm # mm mm mm List List List
1 Bar 1 0 0 35 2 0 0 35 25 10 13
Design Zones
Load Combinations : Construction
Layer Steel Left End Distance to Bar stagger Bottom Right End Distance to Bar stagger Bottom Maximum Minimum Preferred
Load Description 1. Self 2. Extra 3. Live Number type Reference left end of length at left Cover at left Reference right end of length at right Cover at Bar Size Bar Size bar size
Combination Weight Dead Load Load Column bar end end Column bar end Right End
A #.# #.# #.# List # mm mm mm # mm mm mm List List List
1 Construction 1 0 0 1 Bar 1 0 0 35 2 0 0 35 25 10 13
Col No. 1 Characteristic Characteristic Service Service Ultimate Ultimate Ultimate Ultimate kN1 2
Service Service (Reversal) Flexure Flexure Shear Shear 36
(Reversal) (Reversal) (Reversal) 27 23.6
Elastic Rotation #.# 6.33e-4 6.33e-4 5.06e-4 5.06e-4 8.92e-4 8.92e-4 5.41e-4 8.92e-4 18
Elastic Axial Shortening mm 0 0 0 0 0 0 0 0 9
0
Col No. 2 Characteristic Characteristic Service Service Ultimate Ultimate Ultimate Ultimate -9
Service Service (Reversal) Flexure Flexure Shear Shear
-18
(Reversal) (Reversal) (Reversal)
Moment Above kNm 0 0 0 0 0 0 0 0 -27 -23.6
Moment Below kNm 0 0 0 0 0 0 0 0 -36
0 3000mm
Reaction kN 18.75 18.75 15 15 26.44 26.44 16.03 26.44
Elastic Rotation #.# -6.33e-4 -6.33e-4 -5.06e-4 -5.06e-4 -8.92e-4 -8.92e-4 -5.41e-4 -8.92e-4 Shear Shear 1 Shear 2
Elastic Axial Shortening mm 0 0 0 0 0 0 0 0
Flexural Design
Ultimate
Ultimate Design
Flexure 1 2
mm2
1400 0
1 2 70
kNm
-3 0
0 2.56 2.56 -70
3 -140
6 -210
9 -280
12 -350
15 347
-420
18 0 3000mm
21 19.8
0 3000mm Reinforcement Top Total Bottom Total Top Ultimate Bottom Ultimate Min Top Min Bot
0.066
9
12 0 3000mm
15
18 15.6 Neutral Axis Depth Initial Final
21
0 3000mm
MPa1 2MPa 1 2
-3 -1.66 -210 MPa -2.08 MPa
-2 -140 -2 -200
-1 -70
0 0 0 0
1 70
2 140 2 200
3 210 4 400
4 280
5 350 6 600
6 420 8 800
7 1.68 490 2.1
0 3000mm 0 3000mm
Gross Stress Top Gross Stress Bottom Cracked Compression Reinforcement Tension Gross Stress Top Gross Stress Bottom Cracked Compression Reinforcement Tension
MPa1 2MPa 1 2
-3 -1.66 -210 MPa -2.08 MPa
-2 -140 -2 -200
-1 -70
0 0 0 0
1 70
2 140 2 200
3 210 4 400
4 280
5 350 6 600
6 420 8 800
7 1.68 490 2.1
0 3000mm 0 3000mm
Gross Stress Top Gross Stress Bottom Cracked Compression Reinforcement Tension Gross Stress Top Gross Stress Bottom Cracked Compression Reinforcement Tension
0 0 0 0 0 No shear steel
0 0 0 0 0 No shear steel
0 0 0 0 0 No shear steel
0 0 0 0 0 No shear steel
RAPT 6.6.8.0 Project Name: J110 Page 11/13 RAPT 6.6.8.0 Project Name: J110 Page 12/13
Licensee: AECOM Singapore Pte Ltd 1/6/2022 6:51:01 PM License No.: 10479063400712WPN11 Licensee: AECOM Singapore Pte Ltd 1/6/2022 6:51:05 PM License No.: 10479063400712WPN11
Incremental
Spacing of Sets Minimum Legs Shear Comments
2 legs 4 legs 6 legs Min legs mm1 2
H10 H10 H10 H10 0
mm mm mm mm # A
0 0 0 0 0 No shear steel -2
0 0 0 0 0 No shear steel -2.13
0 0 0 0 0 No shear steel
-4
0 0 0 0 0 No shear steel
0 0 0 0 0 No shear steel
0 0 0 0 0 No shear steel -6
0 0 0 0 0 No shear steel 1407
0 0 0 0 0 No shear steel 0 3000mm
0 0 0 0 0 No shear steel
0 0 0 0 0 No shear steel Total Long Term
0 0 0 0 0 No shear steel
0 0 0 0 0 No shear steel mm1 2
0 0 0 0 0 No shear steel 0
0 0 0 0 0 No shear steel
0 0 0 0 0 No shear steel -2
-2.52
-4
-6
Punching 1189
Column Head Critical Section 0 3000mm
Column Bh a at u d fcv P/A Asw/s min V* Mv* V*eff VRd1 VRd2 Asv result
No.
A #.# mm mm mm mm MPa MPa mm2/mm kN kNm kN kN kN mm2 A Detailed Reinforcement
1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Check Not Carried Out! Span 1
2 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Check Not Carried Out! Top Reinforcement Bottom Reinforcement
Design Comments:-
- - Span 1 - Required Bar Size is smaller than the Preferred Bar Size. Maintaining the same cover will require slightly less reinforcement than calculated.
- Span - 1 - Reinforcement added at left span contraflexure point for Offset of Bending Moment Diagram for Shear - 75.96mm2
- Span - 1 - Reinforcement added at right span contraflexure point for Offset of Bending Moment Diagram for Shear - 75.96mm2
Reinforcement Layout
1 2
mm
0
-50
-100
-150
5-H10
-200
0 3000mm
Flat slabs - slabs which rely on flexural action through the slab or slab thickenings such as drop panels or band beams to discrete column supports, require
concentration of the top reinforcement and tendons over supports within a defined width from the column face to facilitate moment transfer to the column. This
width varies and the amount of reinforcement varies for different design codes. In the major codes, the requirements are specified in AS3600 cl 9.1.2,
Eurocode 1992 - 1 - 1 2004 cl 9.4.1, ACI318-14 cl 8.4.2.3 and BS8110 cl3.7.3.1. For example AS3600 requires that 25% of total negative moment for the
entire slab panel be resisted by reinforcement within a width D either side of the column. RAPT cannot define this concentration as it does not know the
transverse spacing of the tendons. It is the designer's responsibility to ensure that these clauses are complied with.
- - Span 1 - Required Bar Size is smaller than the Preferred Bar Size. Maintaining the same cover will require slightly less reinforcement than calculated.
- Span - 1 - Reinforcement added at left span contraflexure point for Offset of Bending Moment Diagram for Shear - 75.96mm2
- Span - 1 - Reinforcement added at right span contraflexure point for Offset of Bending Moment Diagram for Shear - 75.96mm2
RC Column Design
Job Number Sheet
Job Title
Software Consultants (Pty) Ltd Client
Internet: http://www.prokon.com
E-Mail : mail@prokon.com Calcs by Checked by Date
250
500
750
0 Y
Design approach:
The column is designed using an iterative procedure:
(1) An area of reinforcement is chosen.
(2) The column design charts are constructed.
(3) The corresponding slenderness moments are calculated.
(4) The design axis and design ultimate moment are determined .
(5) The design axial force and moment capacity is checked on
the relevant design chart.
(6) The safety factor is calculated for this load case.
lo = ß . l
= 1.8 ×8.8
= 15.840 m
le
max_sl =
r
15.84
=
.17274
= 91.699
Job Number Sheet
Job Title
Software Consultants (Pty) Ltd Client
Internet: http://www.prokon.com
E-Mail : mail@prokon.com Calcs by Checked by Date
5.2(7)
q . l0
eminx =
2
.005 ×15.84
=
2
= 0.0396 m
5.2(7)
q . l0
eminy =
2
.005 ×15.84
=
2
= 0.0396 m
Mminx = eminx. N
= .0396 ×552
= 21.859 kNm
Ned = 552.0 kN
acc. f ck
f cd =
1.50
1 ×40
=
1.50
= 26.667 MPa
Job Number Sheet
Job Title
Software Consultants (Pty) Ltd Client
Internet: http://www.prokon.com
E-Mail : mail@prokon.com Calcs by Checked by Date
fy
f yd =
1.15
450
=
1.15
= 391.304 MPa
5.5.3.1 (1)
Ned
n=
Ac. f cd
552000
=
354110 ×26.667
= 0.0585
A = 0.7
5.8.8.3 (3)
As . f yd
w=
Ac. f cd
5 890.5 ×391.3
=
354110 ×26.667
= 0.2441
5.8.3.1 (1)
B = 1 + 2. w
= 1 + 2 ×.2441
= 1.220
5.8.3.1 (1)
Job Number Sheet
Job Title
Software Consultants (Pty) Ltd Client
Internet: http://www.prokon.com
E-Mail : mail@prokon.com Calcs by Checked by Date
M01
rm =
M02
21.859
=
641.86
= 0.0341
5.8.3.1 (1)
C = 1.7 - rm
= 1.7 - 1
= 0.7000
5.8.3.1 (1)
20 . A . B . C
llim =
n
20 ×.7 ×1.2199 ×.7
=
.05846
= 49.445
Initial moments:
The initial end moments about the X-X axis:
Mi = -0.4 . M1 + 0.6 . M2
= -0.4 ×0 + 0.6 ×-620
= - 372.0000 kNm
Job Number Sheet
Job Title
Software Consultants (Pty) Ltd Client
Internet: http://www.prokon.com
E-Mail : mail@prokon.com Calcs by Checked by Date
Mi2 = 0.4 . M2
= 0.4 ×-620
= - 248.0000 kNm
Mi = -0.4 . M1 + 0.6 . M2
= 0.4
- ×0 + 0.6 ×0
0
= 0.0000×10 kNm
Mi2 = 0.4 . M2
= 0.4 ×0
0
= 0.0000×10 kNm
Ned
n=
Ac. f cd
552000
=
354110 ×26.667
= 0.0585
5.8.8.3 (3)
As . f yd
w=
Ac. f cd
5 890.5 ×391.3
=
354110 ×26.667
= 0.2441
5.8.8.3 (3)
Job Number Sheet
Job Title
Software Consultants (Pty) Ltd Client
Internet: http://www.prokon.com
E-Mail : mail@prokon.com Calcs by Checked by Date
nu = 1 + w
= 1 + .2441
= 1.244
Nbal
nbal =
Ac. f cd
4513×103
=
354110 ×26.667
= 0.4779
5.8.8.3 (3)
nu - n
Kr =
nu - nbal
1.2441 - .05846
=
1.2441 - .47793
= 1.547
Kr is limited to <= 1
f st
eyd =
Es
391.3
=
200000
= 0.0020
5.8.8.3 (4)
f ck l
ß = 0.35 + -
200 150
40 91.7
= 0.35 + -
200 150
= -0.0613
5.8.8.3 (4)
Job Number Sheet
Job Title
Software Consultants (Pty) Ltd Client
Internet: http://www.prokon.com
E-Mail : mail@prokon.com Calcs by Checked by Date
Kf = 1 + ß . f ef
= 1 + -.06133 ×0
= 1.0000
Kf is limited to >= 1
5.8.8.3 (1)
Kr . Kf. eyd
curvature =
0.45 . d
1 ×1 ×.00196
=
0.45 ×.5375
= 0.0081
5.8.8.2 (3)
curvature. lo2
e2 =
c
.00809 ×15.84 2
=
10
= 0.2030
5.8.8.2 (3)
Madd = Ned. e2
= 552 ×.20296
= 112.034 kNm
For bending about the X-X axis, the maximum design moment is the greatest of: 3.8.3.7
(a) 5.8.8.2
Thus 5.8.8.2
M = 641.5 kNm
+ =
Mxbot=620.0 kNm
For bending about the Y-Y axis, the maximum design moment is the greatest of: 3.8.3.7
(a) 5.8.8.2
Thus 5.8.8.2
M = 115.9 kNm
Job Number Sheet
Job Title
Software Consultants (Pty) Ltd Client
Internet: http://www.prokon.com
E-Mail : mail@prokon.com Calcs by Checked by Date
+ =
Mybot=0.0 kNm
Interaction Diagram
Moment max = 1060 kNm @ 3947kN
12E3
11E3
10E3
9000
8000
7000
Axial load (kN)
6000
5000
4000
3000
2000
-1000
1000
1200
-800
-600
-400
-200
0.00
1000
200
400
600
800
552 kN
652 kNm
-1000
-2000
Bending moment (kNm)
Moment distribution along the height of the column for bending about the design axis:
The final design moments were calculated as the vector sum of the X- and Y- moments
of the critical load case. This also determined the design axis direction
Stresses at the bottom end of the column for the critical load case 1
Eurocode 2 - 2004
Y 750
169.8°
500
169.8°
M
D
X X
250
M
D
0
250
500
750
Y
0
Safety
Load case Axis N (kN) M1 (kNm) M2 (kNm) Mi (kNm) Madd (kNm) Design M (kNm) M' (kNm) factor
Assumptions:
X X
500
(1) The general conditions of clause 5.8.8.2 are applicable.
(2) The specified design axial loads include
the self-weight of the column.
(3) The design axial loads are taken constant 0
over the height of the column.
0 Y
Design approach:
The column is designed using an iterative procedure:
(1) An area of reinforcement is chosen.
(2) The column design charts are constructed.
(3) The corresponding slenderness moments are calculated.
(4) The design axis and design ultimate moment are determined .
(5) The design axial force and moment capacity is checked on
the relevant design chart.
(6) The safety factor is calculated for this load case.
lo = ß . l
= 1.3 ×6
= 7.800 m
le
max_sl =
r
7.8
=
.07219
= 108.048
Job Number Sheet
Job Title
Software Consultants (Pty) Ltd Client
Internet: http://www.prokon.com
E-Mail : mail@prokon.com Calcs by Checked by Date
5.2(7)
. l0
eminx =
2
.005 ×7.8
=
2
= 0.0195 m
5.2(7)
. l0
eminy =
2
.005 ×7.8
=
2
= 0.0195 m
Mminx = eminx. N
= .02 ×450
= 9.000 kNm
Ned = 450.0 kN
acc. f ck
f cd =
1.50
1 ×32
=
1.50
= 21.333 MPa
Job Number Sheet
Job Title
Software Consultants (Pty) Ltd Client
Internet: http://www.prokon.com
E-Mail : mail@prokon.com Calcs by Checked by Date
fy
f yd =
1.15
500
=
1.15
= 434.783 MPa
5.5.3.1 (1)
Ned
n=
Ac. f cd
450000
=
248407 ×21.333
= 0.0849
A = 0.7
5.8.8.3 (3)
As . f yd
=
Ac. f cd
1 592.8 ×434.78
=
248407 ×21.333
= 0.1307
5.8.3.1 (1)
B = 1 + 2.
= 1 + 2 ×.13068
= 1.123
5.8.3.1 (1)
Job Number Sheet
Job Title
Software Consultants (Pty) Ltd Client
Internet: http://www.prokon.com
E-Mail : mail@prokon.com Calcs by Checked by Date
M01
rm =
M02
9
=
9
= 1.0000
5.8.3.1 (1)
C = 1.7 - rm
= 1.7 - 1
= 0.7000
5.8.3.1 (1)
20 . A . B . C
lim =
n
20 ×.7 ×1.1231 ×.7
=
.08492
= 37.769
Initial moments:
The initial end moments about the X-X axis:
Mi = -0.4 . M1 + 0.6 . M2
= -0.4 ×0 + 0.6 ×0
= 0.0000×100 kNm
Job Number Sheet
Job Title
Software Consultants (Pty) Ltd Client
Internet: http://www.prokon.com
E-Mail : mail@prokon.com Calcs by Checked by Date
Mi2 = 0.4 . M2
= 0.4 ×0
= 0.0000×100 kNm
Mi = -0.4 . M1 + 0.6 . M2
= -0.4 ×0 + 0.6 ×0
= 0.0000×100 kNm
Mi2 = 0.4 . M2
= 0.4 ×0
= 0.0000×100 kNm
Ned
n=
Ac. f cd
450000
=
248407 ×21.333
= 0.0849
5.8.8.3 (3)
As . f yd
=
Ac. f cd
1 592.8 ×434.78
=
248407 ×21.333
= 0.1307
5.8.8.3 (3)
Job Number Sheet
Job Title
Software Consultants (Pty) Ltd Client
Internet: http://www.prokon.com
E-Mail : mail@prokon.com Calcs by Checked by Date
nu = 1 +
= 1 + .13068
= 1.131
Nbal
nbal =
Ac. f cd
1968×103
=
248407 ×21.333
= 0.3714
5.8.8.3 (3)
nu - n
Kr =
nu - nbal
1.1307 - .08492
=
1.1307 - .37126
= 1.377
Kr is limited to <= 1
f st
yd =
Es
434.78
=
200000
= 0.0022
5.8.8.3 (4)
f ck
ß = 0.35 + -
200 150
32 108.05
= 0.35 + -
200 150
= -0.2103
5.8.8.3 (4)
Job Number Sheet
Job Title
Software Consultants (Pty) Ltd Client
Internet: http://www.prokon.com
E-Mail : mail@prokon.com Calcs by Checked by Date
K = 1 + ß . ef
= 1 + -.21031 ×0
= 1.0000
K is limited to >= 1
5.8.8.3 (1)
5.8.8.2 (3)
curvature. lo2
e2 =
c
.02497 ×7.8 2
=
10
= 0.1519
5.8.8.2 (3)
Madd = Ned. e2
= 450 ×.15189
= 68.350 kNm
For bending about the X-X axis, the maximum design moment is the greatest of: 3.8.3.7
(a) 5.8.8.2
Thus 5.8.8.2
M = 9.0 kNm
+ =
Mxbot=0.0 kNm
For bending about the Y-Y axis, the maximum design moment is the greatest of: 3.8.3.7
(a) 5.8.8.2
Thus 5.8.8.2
M = 77.4 kNm
Job Number Sheet
Job Title
Software Consultants (Pty) Ltd Client
Internet: http://www.prokon.com
E-Mail : mail@prokon.com Calcs by Checked by Date
+ =
Mybot=0.0 kNm
Interaction Diagram
Moment max = 201.2kNm @ 2370kN
6000
5500
5000
4500
4000
Axial load (kN)
3500
3000
2500
2000
1500
1000
-80.0
-60.0
-40.0
-20.0
450 kN
-240
-220
-200
-180
-160
-140
-120
-100
0.00
20.0
40.0
60.0
77 kNm 80.0
500
100
120
140
160
180
200
220
240
-500
Bending moment (kNm)
Moment distribution along the height of the column for bending about the design axis:
The final design moments were calculated as the vector sum of the X- and Y- moments
of the critical load case. This also determined the design axis direction
Stresses at the bottom end of the column for the critical load case 1
Eurocode
Y 2 - 2004
D
M
1000
90.0°
90.0°
X X
500
D
M
Y
0
Safety
Load case Axis N (kN) M1 (kNm) M2 (kNm) Mi (kNm) Madd (kNm) Design M (kNm) M' (kNm) factor
Steel connections
Results
___________________________________________________________________________________________________________________________________
___________________________________________________________________________________________________________________________________
DEMANDS
Description Pu Mu22 Mu33 Vu2 Vu3
[kN] [kN*m] [kN*m] [kN] [kN]
----------------------------------------------------------------------------------------------------------------------------------------------------------
UDL 0.00 0.00 0.00 90.00 0.00
----------------------------------------------------------------------------------------------------------------------------------------------------------
Distance from fasteners to edge [mm] 50.00 24.00 -- pt. 1-8 Table 3.3
e2min = 1.2*d0
= 1.2*20[mm]
= 24[mm] pt. 1-8 Table 3.3
Column
Effective weld throat thickness [mm] 7.00 3.00 -- Sec. 4.5.2
a = 0.7*s
= 0.7*10[mm]
= 7[mm] Sec. 4.5.2
------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Page1
DESIGN CHECK
Verification Unit Capacity Demand Ctrl EQ Ratio References
------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Concrete base
Concrete base bearing of the gross area [KN] 5610.00 0.00 UDL 0.00 DG1 Sec 3.1.1
fcd = cc*fck/c
= 0.85*30[N/mm2]/1.5
= 17[N/mm2]
i = 2.0/3.0
Ac1 = ((bp/hp)*Ncs)*Ncs
= ((500[mm]/220[mm])*1500[mm])*1500[mm]
= 5.11E+06[mm2] DG1 Sec 3.1.1
Ac0 = hp*bp
= 500[mm]*220[mm]
= 1.10E+05[mm2]
1/2
= (LoadedAreaRatio)
1/2
= (46.488)
= 6.818
fjd = i**fcd
= 0.667*6.818*17[N/mm2]
= 77.273[N/mm2]
Base plate
Yielding at bearing interface [KN*m] 15.15 1.30 UDL 0.09 SCI P358 p.231
2
MRd = fyp*tp /(6.0*M0)
2
= 355[N/mm2]*16[mm] /(6.0*1)
= 15.147[kN*m/m] SCI P358 p.231
fcd = cc*fck/c
= 0.85*30[N/mm2]/1.5
= 17[N/mm2]
i = 2.0/3.0
Ac1 = ((bp/hp)*Ncs)*Ncs
= ((500[mm]/220[mm])*1500[mm])*1500[mm]
= 5.11E+06[mm2] DG1 Sec 3.1.1
Ac0 = hp*bp
= 500[mm]*220[mm]
= 1.10E+05[mm2]
1/2
= (LoadedAreaRatio)
1/2
= (46.488)
= 6.818
Page2
fjd = i**fcd
= 0.667*6.818*17[N/mm2]
= 77.273[N/mm2]
2.0
MEd = fjd*c /2.0
2.0
= 77.273[N/mm2]*-5.79[mm] /2.0
= 1.295[kN*m/m] SCI P358 p.231
Bolt tension [KN] 1.447646E12 0.00 UDL 0.00 pt. 1-8 Table 3.4
Ft,Rd = (k2*fub*As)/M2
= (0.9*0.004[N/mm2]*5.03E+17[mm2])/1.25
= 1.45E+12[kN] pt. 1-8 Table 3.4
Column
Weld shear [KN] 1061.72 90.00 UDL 0.08 Eq. 4.3,
Sec 4.5.3.3
(1.0/2.0)
fvwd = (fu/3.0 )/(w*M2)
(1.0/2.0)
= (410[N/mm2]/3.0 )/(0.85*1.25)
= 222.789[N/mm2] pt. 1-8 Eq. 4.4
a = 0.7*s
= 0.7*10[mm]
= 7[mm] Sec. 4.5.2
Fw,Rd = fvwd*a*K
= 222.789[N/mm2]*7[mm]*1
= 1.56[kN/mm] Eq. 4.3
Fw,Rd = Fw,Rd*Lw
= 1.56[kN/mm]*680.8[mm]
= 1061.72[kN] Sec 4.5.3.3
------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Ratio 0.09
------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Major axis
Fasteners
Dimensions
Dimensions Unit Value Min. value Max. value Sta. References
------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Fasteners
Spacing [mm] 120.00 80.00 -- EN 1992-4: 2013,
Sec. 7.2.2.5
smin = 4.0*d
= 4.0*20[mm]
= 80[mm] EN 1992-4: 2013,
Sec. 7.2.2.5
Page3
Concrete cover [mm] 70.00 35.00 -- EN 1991-1: 2004,
Table 4.4N
cmin = 35.0 [mm] EN 1991-1: 2004,
Table 4.4N
DESIGN CHECK
Verification Unit Capacity Demand Ctrl EQ Ratio References
------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Steel failure of fastener in tension [KN] 130.65 0.00 UDL 0.00 [8],
EN 1992-4: 2013,
Table 7.1
2
As = π/4.0*(d - 0.9743 [in]/nt)
2
= π/4.0*(20[mm] - 0.9743 [in]/10.58)
= 244.973[mm2]
NRk,s = As*fuk
= 244.973[mm2]*800[N/mm2]
= 195.978[kN] [8]
NRd,s = NRk,s/Ms
= 195.978[kN]/1.5
= 130.652[kN] EN 1992-4: 2013,
Table 7.1
Pull-out failure of single fastener [KN] 124.69 0.00 UDL 0.00 EN 1992-4: 2013,
Eq. 7.1,
EN 1992-4: 2013,
Table 7.1
2 2
Ah = π*((dh) - d )/4.0
2 2
= π*((34[mm]) - 20[mm] )/4.0
= 593.761[mm2]
CrackedConcrete False
NRk,p = k1*Ah*fck
= 10.5*593.761[mm2]*30[N/mm2]
= 187.035[kN] EN 1992-4: 2013,
Eq. 7.1
NRd,p = NRk,p/Mp
= 187.035[kN]/1.5
= 124.69[kN] EN 1992-4: 2013,
Table 7.1
Page4
Steel failure of fastener in shear [KN] 78.39 22.50 UDL 0.29 EN 1992-4: 2013,
Sec. 7.2.2.3.1
fuk>500.0 [MPa] 800[N/mm2]>500.0 [MPa] True
VRk,s = k50*As*fuk
= 0.5*244.973[mm2]*800[N/mm2]
= 97.989[kN]
DuctileSteel True
VRd,s = VRk,s/Ms
= 97.989[kN]/1.25
= 78.391[kN]
Pry-out failure of single fastener [KN] 170.39 22.50 UDL 0.13 EN 1992-4: 2013,
Eq. 7.13,
EN 1992-4: 2013,
Table 7.1
HasSupplementaryReinforcement False
c1Left = 1.5*hef
= 1.5*150[mm]
= 225[mm] EN 1992-4: 2013,
Fig. 7.4
c1Left = 1.5*hef
= 1.5*150[mm]
= 225[mm] EN 1992-4: 2013,
Fig. 7.4
Page5
c1Left<1.5*hef 1130[mm]<1.5*150[mm] False
c1Left = 1.5*hef
= 1.5*150[mm]
= 225[mm] EN 1992-4: 2013,
Fig. 7.4
c1Left = 1.5*hef
= 1.5*150[mm]
= 225[mm] EN 1992-4: 2013,
Fig. 7.4
IsCloseToThreeEdges False
hef = hef
= 150[mm] EN 1992-4: 2013,
Sec. 7.2.1.6
ccr,N = 1.5*hef
= 1.5*150[mm]
= 225[mm] EN 1992-4: 2013,
Sec. 7.2.1.6
d = t - Cover - dre/2.0
= 250[mm] - 70[mm] - 0[mm]/2.0
= 180[mm] EN 1992-4: 2013,
Sec. 6.4.3
Page6
d = Min(d, Min(2.0*hef, 2.0*c1))
= Min(180[mm], Min(2.0*150[mm], 2.0*870[mm]))
= 180[mm] EN 1992-4: 2013,
Sec. 6.4.3
z = 0.85*d
= 0.85*180[mm]
= 153[mm] EN 1992-4: 2013,
Sec. 6.4.3
ExistEffectOfCompressionForce False
CrackedConcrete False
NRk,c = N0Rk,c*Ac,N/A0c,N*s,N*re,N*ec,N*M,N
= 127.791[kN]*2.03E+05[mm2]/2.03E+05[mm2]*1*1*1*1
= 127.791[kN] EN 1992-4: 2013,
Eq. 7.13
VRk,cp = k3*NRk,c
= 2*127.791[kN]
= 255.583[kN]
NRd,c = NRk,c/Mc
= 255.583[kN]/1.5
= 170.388[kN] EN 1992-4: 2013,
Table 7.1
Concrete edge failure of single fastener [KN] 106.93 22.50 UDL 0.21 EN 1992-4: 2013,
Eq. 7.39,
EN 1992-4: 2013,
Table 7.2
c2Left<1.5*c1 940[mm]<1.5*1130[mm] True
c2Left = c2Left
= 940[mm] EN 1992-4: 2013,
Fig. 7.12
c2Right = c2Right
= 1060[mm] EN 1992-4: 2013,
Fig. 7.12
Page7
h<1.5*c1 250[mm]<1.5*1130[mm] True
h=h
= 250[mm] EN 1992-4: 2013,
Fig. 7.12
IsCloseToThreeEdges True
c1 = max(c2,max/1.5, h/1.5)
= max(1060[mm]/1.5, 250[mm]/1.5)
= 706.667[mm] EN 1992-4: 2013,
Fig. 7.14
c2Left = c2Left
= 940[mm] EN 1992-4: 2013,
Fig. 7.12
c2Right = 1.5*c1
= 1.5*706.667[mm]
= 1060[mm] EN 1992-4: 2013,
Fig. 7.12
h=h
= 250[mm] EN 1992-4: 2013,
Fig. 7.12
Page8
re,V = 1.0 EN 1992-4: 2013,
Sec. 7.2.2.5 (10)
CrackedConcrete False
VRkc = V0Rk,c*AcV/A0cV*s,V*h,V*ec,V*,V*re,V
= 362.414[kN]*5.00E+05[mm2]/2.25E+06[mm2]*0.966*2.059*1*1*1
= 160.402[kN] EN 1992-4: 2013,
Eq. 7.39
VRd,c = VRkc/Mc
= 160.402[kN]/1.5
= 106.935[kN] EN 1992-4: 2013,
Table 7.2
Concrete edge failure of group of fasteners [KN] 112.31 90.00 UDL 0.80 EN 1992-4: 2013,
Eq. 7.39,
EN 1992-4: 2013,
Table 7.2
2.0
A0cV = 4.5*c1
2.0
= 4.5*626.667[mm]
= 1.77E+06[mm2] EN 1992-4: 2013,
Eq. 7.43
Page9
s,V = min(0.7 + 0.3*c2/(1.5*c1), 1.0)
= min(0.7 + 0.3*940[mm]/(1.5*626.667[mm]), 1.0)
=1 EN 1992-4: 2013,
Eq. 7.44
0.5
h,V = max((1.5*c1/h) , 1.0)
0.5
= max((1.5*626.667[mm]/250[mm]) , 1.0)
= 1.939 EN 1992-4: 2013,
Eq. 7.45
CrackedConcrete False
VRkc = V0Rk,c*AcV/A0cV*s,V*h,V*ec,V*,V*re,V
= 307.074[kN]*5.00E+05[mm2]/1.77E+06[mm2]*1*1.939*1*1*1
= 168.469[kN] EN 1992-4: 2013,
Eq. 7.39
Page10
VRd,c = VRkc/Mc
= 168.469[kN]/1.5
= 112.313[kN] EN 1992-4: 2013,
Table 7.2
------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Ratio 0.80
------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Major axis
Maximum compression and tension (UDL)
------------------------------------------------------------------------------------------------------------------------------------
Maximum bearing pressure 0.00 [N/mm2]
Minimum bearing pressure 0.00 [N/mm2]
Maximum anchor tension 0.00 [kN]
Minimum anchor tension 0.00 [kN]
Neutral axis angle 0.00 [deg]
Bearing length 0.00 [mm]
------------------------------------------------------------------------------------------------------------------------------------
Anchors tensions
Anchor Transverse Longitudinal Shear Tension
[mm] [mm] [kN] [kN]
----------------------------------------------------------------------------------------------------------------------------------------------------------
1 -60.00 -130.00 22.50 0.00
2 60.00 -130.00 22.50 0.00
3 60.00 130.00 22.50 0.00
4 -60.00 130.00 22.50 0.00
----------------------------------------------------------------------------------------------------------------------------------------------------------
Page11
Major axis
Results for shear breakout (UDL)
NOTATION
a: Effective throat size of the weld, distance between the first line of bolts and the face of the support
As: Tensile stress area of the bolt or of the anchor bolt
w: Correlation factor taken from Table 4.1
d0: Hole diameter
e2min: Minimum vertical edge distance
Ft,Rd: Design tension resistance per bolt
fu: Ultimate tensile strength of the steel on which the bolt bears
fub: Ultimate tensile strength of the bolt
fvwd: Design shear strength of fillet welds
Fw,Rd: Design weld resistance per unit length
Fw,Rd: Design weld resistance
M2: Partial factor for resistance of cross-sections in tension to fracture
k2: Stiffenes coefficient
K: Weld force angle factor
Lw: Length of weld
s: Weld size
Ac0: Loaded area
Ac1: Maximum design distribution area
: Coefficient for difussion of the concentrated force
cc: Concrete compressive strength factor
bp: Base plate width
i: Bearing strength factor
c: Effective area projection
fcd: Design value of concrete compressive strength
fck: Concrete cylinder strength
fjd: Design bearing strength
FRd: Design resistance
fyp: Yield strength of the plate
c: Material factor for concrete
M0: Partial factor for steel resistance
hc: Column depth
hp: Base plate height
l: Weld length
lw,eff: Total effective length of the welds in direction of the shear
LoadedAreaRatio: Distributed to loaded area ratio
s: Weld size
tp: Base plate thickness
MRd: Unitary bending design resistance
MEd: Unitary design moment
Ncs: Length of the concrete supporting surface or pier parallel to moment design direction
hpmin: Minimum base plate heigth
bpmin: Minimum base plate width
Page12
Ac,N: Actual projected area
AcV: Actual projected area for concrete edge failure
Ah: Load bearing area of the head of the fastener
As: Fastener effective area for tension and shear
A0c,N: Reference projected area
A0cV: Reference projected area for concrete edge failure
: Influence length to edge distance factor
V: Angle between the design shear load and the line perpendicular to the verified edge
: Fastener diameter to edge distance factor
c: Edge distance from an axis of a fastener
c 1: Edge distance in direction 1
c1Left: Distance from the fastener center to the left edge of the concrete base
c1Right: Distance from the fastener center to the right edge of the concrete base
c 2: Edge distance in direction 2 (Perpendicular to direction 1)
c2Bot: Distance from the fastener center to the bottom edge of the concrete base
c2Left: Left edge distance
c2,max: Larger of two edge distances parallel to the direction of loading
c2Right: Right edge distance
c2Top: Distance from the fastener center to the top edge of the concrete base
ccr,N: Characteristic edge distance
CrackedConcrete: Concrete is cracked
d: Nominal fastener diameter
dh: Diameter of fastener head
DuctileSteel: Flag to indicate tha the steel is ductile
eV: Eccentricity of the resulting shear load acting on the fasteners
ExistEffectOfCompressionForce: Compression force between fixture and concrete exists
fck: Characteristic cube strength of the concrete strength class
fuk: Characteristic steel yield strength
fyk: Characteristic steel ultimate tensile strength
Mc: Partial factor for concrete
Mp: Partial factor for pull out failure
Ms: Partial factor for steel
h: Thickness of concrete member in which the fastener is installed
hef: Effective embedment depth
HasSupplementaryReinforcement: Flag to indicate that the concrete base has supplementary reinforcement
IsCloseToThreeEdges: Flag to indicate that the fastener or group of fasteners are close to three or more edges
k1: Pull-out failure factor
k3: Pry-out failure factor
k5: Concrete edge failure factor
k50: Shear steel failure factor
k51: Non-ductile steel factor
k9: Concrete cone failure factor
lf: Influence length
LV: Length of the actual projected area for concrete edge failure
n: Number of fasteners in the group
NRd,c: Design resistance of a fasterner or group of fastener for concrete cone failure
NRd,p: Design resistance for pull out failure
NRd,s: Design resistance for steel failure
NRk,c: Characteristic resistance of a fasterner or group of fastener for concrete cone failure
NRk,p: Characteristic resistance for pull out failure
NRk,s: Characteristic resistance of a single fastener for tensile steel failure
nt: Number of threads per inch
N0Rk,c: Characteristic resistance of a single fasterner for concrete cone failure
,V: Applied load angle factor for concrete edge failure
ec,N: Load eccentricity factor
ec,V: Load eccentricity factor for concrete edge failure
h,V: Resistance reduction factor for concrete edge failure
M,N: Factor that takes into account the effect of a compression force between fixture and concrete
re,N: Shell spalling factor
re,V: Reinforcement located on edge factor for concrete edge failure
s,N: Stress distribution factor
s,V: Stress distribution factor for concrete edge failure
t: Base plate thickness
Page13
VRd,c: Design resistance for concrete edge failure
VRd,s: Design resistance of a single fastener for shear steel failure
VRkc: Characteristic resistance for concrete edge failure
VRk,cp: Characteristic resistance for pry-out failure
VRk,s: Characteristic resistance of a single fastener for shear steel failure
V0Rk,c: Characteristic resistance of a single fastener for concrete edge failure
z: Internal lever arm calculated according to the theory of elasticity
d: Concrete base effective depth
Cover: Concrete cover
dre: Reinforcement diameter
smin: Fastener minimum spacing
REFERENCES
[8] International Federation for Structural Concrete (2011). Design of Anchorages in Concrete. CEP-FIP. Lousanne, Switzerland.
Page14
AECOM
Current Date: 1/6/2022 6:56 PM
Units system: SI
File name: C:\Users\sujeevanleonard.tham\OneDrive - AECOM\Projects\J110\J110\OneDrive_2021-07-01\12. Southern Staircase\Design
Files\Str\Connection Design\B40B TO B40B.rcnx
Steel connections
Results
____________________________________________________________________________________________________________________________
___________________________________________________________________________________
DEMANDS
Description Pu Ru RuLeft Mu Mmax C1
[kN] [kN] [kN] [kN*m] [kN*m]
-----------------------------------------------------------------------------------------------------------
UDL 0.00 90.00 0.00 0.00 0.00 0.00
-----------------------------------------------------------------------------------------------------------
GEOMETRIC CONSIDERATIONS
Dimensions Unit Value Min. value Max. value Sta. References
----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Fin plate
Length [mm] 320.00 245.64 359.40 [1]
Lmin = 0.6*hb
= 0.6*409.4[mm]
= 245.64[mm] [1]
Lmin = 0.6*hb
= 0.6*409.4[mm]
= 245.64[mm] [1]
Vertical center-to-center spacing (pitch) [mm] 80.00 39.60 140.00 pt. 1-8 Table 3.3
p1 = 2.2*d0
= 2.2*18[mm]
= 39.6[mm] pt. 1-8 Table 3.3
HasDoubleNotchTrue
dnmax = hb/5
= 409.4[mm]/5
= 81.88[mm] [1]
lnmax = hb
= 409.4[mm] [1]
dnmax = hb/5
= 409.4[mm]/5
= 81.88[mm] [1]
lnmax = hb
= 409.4[mm] [1]
DESIGN CHECK
Verification Unit Capacity Demand Ctrl EQ Ratio References
------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Plate (beam side)
Bolt group shear [KN] 192.51 90.00 UDL 0.47 pt. 1-8 Table 3.4,
SCI P358 p.115
Fv,Rd = (v*fub*A)/M2
= (0.6*800[N/mm2]*156.668[mm2])/1.25
= 60.161[kN] pt. 1-8 Table 3.4
z = zp + (n2 - 1)*p2/2
= 50[mm] + (1 - 1)*60[mm]/2
= 50[mm] SCI P358 p.115
IsSingleLineOfBoltsTrue
IsSingleLineOfBoltsTrue
IsSingleLineOfBoltsTrue
= (6*z)/(n1*(n1 + 1)*p1)
= (6*50[mm])/(4*(4 + 1)*80[mm])
= 0.188 SCI P358 p.115
Bolt group bearing [KN] 382.12 90.00 UDL 0.24 pt. 1-8 Table 3.4,
SCI P358 p.116
IsSingleLineOfBoltsTrue
d = e1/(3.0*d0)
= 40[mm]/(3.0*18[mm])
= 0.741 pt. 1-8 Table 3.4
d = p1/(3.0*d0) - 1.0/4.0
= 80[mm]/(3.0*18[mm]) - 1.0/4.0
= 1.231 pt. 1-8 Table 3.4
Fb,Rd = (k1*b*fu*d*t)/M2
= (2.5*0.741*470[N/mm2]*16[mm]*10[mm])/1.25
= 111.407[kN] pt. 1-8 Table 3.4
k1 = min(2.8*e1/d0 - 1.7, 1.4*p1/d0 - 1.7, 2.5)
= min(2.8*40[mm]/18[mm] - 1.7, 1.4*80[mm]/18[mm] - 1.7, 2.5)
= 2.5 [4]
d = e2/(3.0*d0)
= 50[mm]/(3.0*18[mm])
= 0.926 [4]
Fb,Rd = (k1*b*fu*d*t)/M2
= (2.5*0.926*470[N/mm2]*16[mm]*10[mm])/1.25
= 139.259[kN] pt. 1-8 Table 3.4
z = zp + (n2 - 1)*p2/2
= 50[mm] + (1 - 1)*60[mm]/2
= 50[mm] SCI P358 p.115
IsSingleLineOfBoltsTrue
IsSingleLineOfBoltsTrue
IsSingleLineOfBoltsTrue
= (6*z)/(n1*(n1 + 1)*p1)
= (6*50[mm])/(4*(4 + 1)*80[mm])
= 0.188 SCI P358 p.115
Vpl,Rd = Av*(fy/(3)0.5)/M0/1.27
= 3200[mm2]*(355[N/mm2]/(3)0.5)/1/1.27
= 516.433[kN] [4]
VRd,n = Av,net*fu,p/(3)0.5/M2
= 2480[mm2]*470[N/mm2]/(3)0.5/1.25
= 538.368[kN] [4]
Block tearing [KN] 521.84 90.00 UDL 0.17 pt. 1-8 Eq. 3.10
IsSingleLineOfBoltsTrue
Ant = tp*(e2 - d0/2)
= 10[mm]*(50[mm] - 18[mm]/2)
= 410[mm2] SCI P358 p.118
Lateral torsional buckling [KN] 1211.73 90.00 UDL 0.07 pt. 1-1 Eq. 6.55,
pt. 1-1 Eq. 6.13,
SCI P358 p.119
= 0.6 SCI P358 p.119
Wpl = tp*hp2/6
= 10[mm]*320[mm]2/6
= 1.71E+05[mm3] [4]
LT = 2.8/86.8*((zp*hp)/(1.5*tp2))0.5
= 2.8/86.8*((50[mm]*320[mm])/(1.5*10[mm]2))0.5
= 0.333 SCI P358 p.119
Mb,Rd = LT*Wpl*fy/M1
= 0.899*1.71E+05[mm3]*355[N/mm2]/1
= 54.464[kN*m] pt. 1-1 Eq. 6.55
Mc,Rd = Wpl*fy/M0
= 1.71E+05[mm3]*355[N/mm2]/1
= 60.587[kN*m] pt. 1-1 Eq. 6.13
z = zp + (n2 - 1)*p2/2
= 50[mm] + (1 - 1)*60[mm]/2
= 50[mm] SCI P358 p.115
zp>tp/0.1550[mm]>10[mm]/0.15False
VRd = Mc,Rd/z
= 60.587[kN*m]/50[mm]
= 1211.73[kN] SCI P358 p.119
Beam
Bolt bearing [KN] 346.16 90.00 UDL 0.26 pt. 1-8 Table 3.4,
SCI P358 p.116
IsSingleLineOfBoltsTrue
d = p1/(3.0*d0) - 1.0/4.0
= 80[mm]/(3.0*18[mm]) - 1.0/4.0
= 1.231 pt. 1-8 Table 3.4
Fb,Rd = (k1*b*fu*d*t)/M2
= (2.5*1*470[N/mm2]*16[mm]*8.8[mm])/1.25
= 132.352[kN] pt. 1-8 Table 3.4
d = e2/(3.0*d0)
= 35[mm]/(3.0*18[mm])
= 0.648 [4]
Fb,Rd = (k1*b*fu*d*t)/M2
= (2.5*0.648*470[N/mm2]*16[mm]*8.8[mm])/1.25
= 85.784[kN] pt. 1-8 Table 3.4
z = zp + (n2 - 1)*p2/2
= 50[mm] + (1 - 1)*60[mm]/2
= 50[mm] SCI P358 p.115
IsSingleLineOfBoltsTrue
IsSingleLineOfBoltsTrue
IsSingleLineOfBoltsTrue
= (6*z)/(n1*(n1 + 1)*p1)
= (6*50[mm])/(4*(4 + 1)*80[mm])
= 0.188 SCI P358 p.115
Shear at gross section [KN] 583.41 90.00 UDL 0.15 pt. 1-1 Eq. 6.18
Av,DN = 0.9*(hb - dnt - dnb)*tw
= 0.9*(409.4[mm] - 25[mm] - 25[mm])*8.8[mm]
= 2846.45[mm2] SCI P358 p.18,
p.124
Vpl,Rd = Av*(fy/(3)0.5)/M0
= 2846.45[mm2]*(355[N/mm2]/(3)0.5)/1
= 583.406[kN] pt. 1-1 Eq. 6.18
Shear at net section [KN] 480.37 90.00 UDL 0.19 SCI P358 p.121
Av,DN = 0.9*(hb - dnt - dnb)*tw
= 0.9*(409.4[mm] - 25[mm] - 25[mm])*8.8[mm]
= 2846.45[mm2] SCI P358 p.18,
p.124
Av,net = Av - n1*d0*tw
= 2846.45[mm2] - 4*18[mm]*8.8[mm]
= 2212.85[mm2] SCI P358 p.121
VRd,n = Av,net*fu/(3)0.5/M2
= 2212.85[mm2]*470[N/mm2]/(3)0.5/1.25
= 480.373[kN] SCI P358 p.121
Block tearing [KN] 469.94 90.00 UDL 0.19 pt. 1-8 Eq. 3.10
IsSingleLineOfBoltsTrue
Shear and bending interaction at the notch [KN*m] 67.25 8.55 UDL 0.13 SCI P358 p.18,
p.124,
pt. 1-1 Cl. 6.2.8
Av,DN = 0.9*(hb - dnt - dnb)*tw
= 0.9*(409.4[mm] - 25[mm] - 25[mm])*8.8[mm]
= 2846.45[mm2] SCI P358 p.18,
p.124
Vpl,DN,Rd = Av,DN*fy/((3.0)0.5*M0)
= 2846.45[mm2]*355[N/mm2]/((3.0)0.5*1)
= 583.406[kN] SCI P358 p.18,
p.124
VEd< = 0.5*Vpl,DN,Rd90[kN]<
= 0.5*583.406[kN]True
a = 0.7*s
= 0.7*8[mm]
= 5.6[mm] Sec. 4.5.2
= VEd/(2.0*a*Lw)
= 90[kN]/(2.0*5.6[mm]*320[mm])
= 25.112[N/mm2] pt. 1-8 Eq. 4.1
w = (
[N/mm2][N/mm2][N/mm2]
[N/mm2]
Support
Web or wall local shear with one beam [KN] 577.17 90.00 UDL 0.16 pt. 1-1 Eq. 6.18
Av = hp*t2
= 320[mm]*8.8[mm]
= 2816[mm2] SCI P358 p.128
Vpl,Rd = Av*(fy/(3)0.5)/M0
= 2816[mm2]*(355[N/mm2]/(3)0.5)/1
= 577.166[kN] pt. 1-1 Eq. 6.18
Web or wall punching shear [KN] 1129.40 90.00 UDL 0.08 SCI P358 p.128
Wpl = tp*hp2/6
= 10[mm]*320[mm]2/6
= 1.71E+05[mm3] [4]
z = zp + (n2 - 1)*p2/2
= 50[mm] + (1 - 1)*60[mm]/2
= 50[mm] SCI P358 p.115
VRd = (Wpl*fu*t2/tp)/(z*M2)
= (1.71E+05[mm3]*470[N/mm2]*8.8[mm]/10[mm])/(50[mm]*1.25)
= 1129.4[kN] SCI P358 p.128
M2 = Mu
= 1.1 SCI P358 p.4
Nu,Rd = 0.9*Anet*fu/M2
= 0.9*2480[mm2]*470[N/mm2]/1.1
= 953.673[kN] pt. 1-1 Eq. 6.7
Block tearing due to tension [KN] 962.79 0.00 UDL 0.00 pt. 1-8 Eq. 3.9
Ant = tp*((n1 - 1)*p1 - (n1 - 1)*d0)
= 10[mm]*((4 - 1)*80[mm] - (4 - 1)*18[mm])
= 1860[mm2] SCI P358 p.130
IsSingleLineOfBoltsTrue
M2 = Mu
= 1.1 SCI P358 p.4
IsSingleLineOfBoltsTrue
M2 = Mu
= 1.1 SCI P358 p.4
Bolt shear [KN] 273.46 0.00 UDL 0.00 pt. 1-8 Table 3.4
M2 = Mu
= 1.1 SCI P358 p.4
Fv,Rd = (v*fub*A)/M2
= (0.6*800[N/mm2]*156.668[mm2])/1.1
= 68.364[kN] pt. 1-8 Table 3.4
FRd = n*Fv,Rd
= 4*68.364[kN]
= 273.457[kN] pt. 1-8 Table 3.4
Bolt bearing due to tension [KN] 633.00 0.00 UDL 0.00 pt. 1-8 Table 3.4
M2 = Mu
= 1.1 SCI P358 p.4
d = e2/(3.0*d0)
= 50[mm]/(3.0*18[mm])
= 0.926 [4]
Fb,Rd = (k1*b*fu*d*t)/M2
= (2.5*0.926*470[N/mm2]*16[mm]*10[mm])/1.1
= 158.249[kN] pt. 1-8 Table 3.4
FRd = n*Fb,Rd
= 4*158.249[kN]
= 632.997[kN] pt. 1-8 Table 3.4
M2 = Mu
= 1.1 SCI P358 p.4
Nu,Rd = 0.9*Anet*fu/M2
= 0.9*2182.4[mm2]*470[N/mm2]/1.1
= 839.232[kN] pt. 1-1 Eq. 6.7
Block tearing due to tension [KN] 793.15 0.00 UDL 0.00 pt. 1-8 Eq. 3.9
Ant = tw*((n1 - 1)*p1 - (n1 - 1)*d0)
= 8.8[mm]*((4 - 1)*80[mm] - (4 - 1)*18[mm])
= 1636.8[mm2] SCI P358 p.131
IsSingleLineOfBoltsTrue
M2 = Mu
= 1.1 SCI P358 p.4
IsSingleLineOfBoltsTrue
M2 = Mu
= 1.1 SCI P358 p.4
Bolt bearing due to tension [KN] 389.93 0.00 UDL 0.00 pt. 1-8 Table 3.4
M2 = Mu
= 1.1 SCI P358 p.4
d = e2/(3.0*d0)
= 35[mm]/(3.0*18[mm])
= 0.648 [4]
Fb,Rd = (k1*b*fu*d*t)/M2
= (2.5*0.648*470[N/mm2]*16[mm]*8.8[mm])/1.1
= 97.481[kN] pt. 1-8 Table 3.4
FRd = n*Fb,Rd
= 4*97.481[kN]
= 389.926[kN] pt. 1-8 Table 3.4
WARNINGS
- Overall stability of the beam (lateral torsional buckling) should be checked while designing the member considering the reduction of area due to the
notch.
------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
NOTATION
a: Effective throat size of the weld, distance between the first line of bolts and the face of the support
A: Gross section area
Anet: Net area subjected to tension
Ant: Net area subjected to tension
Anv: Net area subjected to shear
Av : Shear area
Av,DN: Shear area at double notched beam
Av,net: Net shear area
: Fin plate bolt group factor
b: Bolt bearing resistance factor, Table 3.4
d: Bolt bearing resistance factor, Table 3.4
LT: Imperfection factor
v: Bolt shear resistance factor, Table 3.4
: Fin plate bolt group factor
w: Correlation factor taken from Table 4.1
d: Nominal bolt diameter
d0: Hole diameter
demin: Minimum edge distance
dnmin: Minimum notch depth
dnb: Bottom notch height
dnmax: Maximum notch height
dnt: Top notch height
e1: End distance
e2: Edge distance
Fb,Rd: Design bearing resistance per bolt
Fb,Rd,hor: Design bearing resistance per bolt in a horizontal direction
Fb,Rd,ver: Design bearing resistance per bolt in a vertical direction
FRd: Design resistance of the bolt group
fu: Ultimate tensile strength of the steel on which the bolt bears
fu: Ultimate tensile strength
fub: Ultimate tensile strength of the bolt
fu,p: Ultimate tensile strength of the bolt
fu: Nominal ultimate tensile strength of the weaker part joined
Fv,Rd: Design shear resistance per bolt
fvwd: Design shear strength of fillet welds
fy: Yield strength
fy,p: Yield strength of the plate material
gh: Horizontal gap between members
M0: Partial factor for resistance of cross-sections whatever the class is
M1: Partial factor for resistance of members to instability assessed by member checks
M2: Partial factor for resistance of cross-sections in tension to fracture
Mu: Partial factor for resistance of components when verifying structural integrity
hb: Height of the member
hp: Height of plate
HasDoubleNotch: Has double notch
Ibg: Moment of inertia of bolt group
IsSingleLineOfBolts: Single line of bolts
k 1: Bolt bearing factor
ktop: Thickness of the top flange + root radius
kbottom: Thickness of the bottom flange + root radius
: Factor to account for the triangular shape of the bending moment diagram in the fin plate
Lmax: Maximum length
Lmin: Minimum length
ln: Notch length
lnmax: Maximum notch length
Lw: Length of weld
LT: Non dimensional slenderness for lateral-torsional buckling
LT: Reduction factor for lateral-torsional buckling
Mb,Rd: Design buckling resistance moment
Mc,Rd: Design resistance for bending about one principal axis of a cross-section
MEd: Design moment
Mv,DN,Rd: Moment resistance of a double notched beam at the notch
n: Total number of bolts
n1: Number of horizontal bolt rows
n2: Number of vertical bolt rows
Nu,Rd: Design ultimate resistance of the net section at holes
p1: Vertical spacing between centres of bolts in a line in the load direction
p2: Horizontal spacing between centres of bolts in adjacent lines perpendicular to the load direction
pmax: Maximum bolts spacing
LT: Value to determine lateral-torsional buckling reduction factor
rb : Root radius of the beam section
rs : Root radius of the support section
s: Weld size
REFERENCES
[1] Joints in Steel Construction – Simple Joints to Eurocode 3 (P358), SCI and BCSA, 2011.
[4] SN017 NCCI: Shear resistance of a fin plate connection.
AECOM
Current Date: 1/6/2022 7:07 PM
Units system: SI
File name: C:\Users\sujeevanleonard.tham\OneDrive - AECOM\Projects\J110\J110\OneDrive_2021-07-01\12. Southern Staircase\Design
Files\Str\Connection Design\B50A TO 50A.rcnx
Steel connections
Results
____________________________________________________________________________________________________________________________
___________________________________________________________________________________
DEMANDS
Description Pu Ru RuLeft Mu Mmax C1
[kN] [kN] [kN] [kN*m] [kN*m]
-------------------------------------------------------------------------------------------------------------
UDL 0.00 280.00 0.00 0.00 0.00 0.00
-------------------------------------------------------------------------------------------------------------
GEOMETRIC CONSIDERATIONS
Dimensions Unit Value Min. value Max. value Sta. References
----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Fin plate
Length [mm] 450.00 316.98 468.30 [1]
Lmin = 0.6*hb
= 0.6*528.3[mm]
= 316.98[mm] [1]
Lmin = 0.6*hb
= 0.6*528.3[mm]
= 316.98[mm] [1]
Vertical center-to-center spacing (pitch) [mm] 70.00 48.40 200.00 pt. 1-8 Table 3.3
p1 = 2.2*d0
= 2.2*22[mm]
= 48.4[mm] pt. 1-8 Table 3.3
HasDoubleNotchTrue
dnmax = hb/5
= 528.3[mm]/5
= 105.66[mm] [1]
lnmax = 110000*hb/(hb/tw)3
= 110000*528.3[mm]/(528.3[mm]/9.6[mm])3
= 348.695[mm] [1]
dnmax = hb/5
= 528.3[mm]/5
= 105.66[mm] [1]
lnmax = 110000*hb/(hb/tw)3
= 110000*528.3[mm]/(528.3[mm]/9.6[mm])3
= 348.695[mm] [1]
DESIGN CHECK
Verification Unit Capacity Demand Ctrl EQ Ratio References
------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Plate (beam side)
Bolt group shear [KN] 454.52 280.00 UDL 0.62 pt. 1-8 Table 3.4,
SCI P358 p.115
Fv,Rd = (v*fub*A)/M2
= (0.6*800[N/mm2]*244.794[mm2])/1.25
= 94.001[kN] pt. 1-8 Table 3.4
z = zp + (n2 - 1)*p2/2
= 60[mm] + (1 - 1)*60[mm]/2
= 60[mm] SCI P358 p.115
IsSingleLineOfBoltsTrue
IsSingleLineOfBoltsTrue
IsSingleLineOfBoltsTrue
= (6*z)/(n1*(n1 + 1)*p1)
= (6*60[mm])/(6*(6 + 1)*70[mm])
= 0.122 SCI P358 p.115
Bolt group bearing [KN] 1166.08 280.00 UDL 0.24 pt. 1-8 Table 3.4,
SCI P358 p.116
IsSingleLineOfBoltsTrue
d = e1/(3.0*d0)
= 50[mm]/(3.0*22[mm])
= 0.758 pt. 1-8 Table 3.4
d = p1/(3.0*d0) - 1.0/4.0
= 70[mm]/(3.0*22[mm]) - 1.0/4.0
= 0.811 pt. 1-8 Table 3.4
Fb,Rd = (k1*b*fu*d*t)/M2
= (2.5*0.758*470[N/mm2]*20[mm]*16[mm])/1.25
= 227.879[kN] pt. 1-8 Table 3.4
k1 = min(2.8*e1/d0 - 1.7, 1.4*p1/d0 - 1.7, 2.5)
= min(2.8*50[mm]/22[mm] - 1.7, 1.4*70[mm]/22[mm] - 1.7, 2.5)
= 2.5 [4]
d = e2/(3.0*d0)
= 60[mm]/(3.0*22[mm])
= 0.909 [4]
Fb,Rd = (k1*b*fu*d*t)/M2
= (2.5*0.909*470[N/mm2]*20[mm]*16[mm])/1.25
= 273.455[kN] pt. 1-8 Table 3.4
z = zp + (n2 - 1)*p2/2
= 60[mm] + (1 - 1)*60[mm]/2
= 60[mm] SCI P358 p.115
IsSingleLineOfBoltsTrue
IsSingleLineOfBoltsTrue
IsSingleLineOfBoltsTrue
= (6*z)/(n1*(n1 + 1)*p1)
= (6*60[mm])/(6*(6 + 1)*70[mm])
= 0.122 SCI P358 p.115
Vpl,Rd = Av*(fy/(3)0.5)/M0/1.27
= 7200[mm2]*(355[N/mm2]/(3)0.5)/1/1.27
= 1161.97[kN] [4]
VRd,n = Av,net*fu,p/(3)0.5/M2
= 5088[mm2]*470[N/mm2]/(3)0.5/1.25
= 1104.52[kN] [4]
Block tearing [KN] 1062.33 280.00 UDL 0.26 pt. 1-8 Eq. 3.10
IsSingleLineOfBoltsTrue
Ant = tp*(e2 - d0/2)
= 16[mm]*(60[mm] - 22[mm]/2)
= 784[mm2] SCI P358 p.118
Lateral torsional buckling [KN] 3195.00 280.00 UDL 0.09 pt. 1-1 Eq. 6.55,
pt. 1-1 Eq. 6.13,
SCI P358 p.119
= 0.6 SCI P358 p.119
Wpl = tp*hp2/6
= 16[mm]*450[mm]2/6
= 5.40E+05[mm3] [4]
LT = 2.8/86.8*((zp*hp)/(1.5*tp2))0.5
= 2.8/86.8*((60[mm]*450[mm])/(1.5*16[mm]2))0.5
= 0.27 SCI P358 p.119
Mb,Rd = LT*Wpl*fy/M1
= 0.946*5.40E+05[mm3]*355[N/mm2]/1
= 181.267[kN*m] pt. 1-1 Eq. 6.55
Mc,Rd = Wpl*fy/M0
= 5.40E+05[mm3]*355[N/mm2]/1
= 191.7[kN*m] pt. 1-1 Eq. 6.13
z = zp + (n2 - 1)*p2/2
= 60[mm] + (1 - 1)*60[mm]/2
= 60[mm] SCI P358 p.115
zp>tp/0.1560[mm]>16[mm]/0.15False
VRd = Mc,Rd/z
= 191.7[kN*m]/60[mm]
= 3195[kN] SCI P358 p.119
Beam
Bolt bearing [KN] 661.10 280.00 UDL 0.42 pt. 1-8 Table 3.4,
SCI P358 p.116
IsSingleLineOfBoltsTrue
d = p1/(3.0*d0) - 1.0/4.0
= 70[mm]/(3.0*22[mm]) - 1.0/4.0
= 0.811 pt. 1-8 Table 3.4
Fb,Rd = (k1*b*fu*d*t)/M2
= (2.5*0.811*470[N/mm2]*20[mm]*9.6[mm])/1.25
= 146.298[kN] pt. 1-8 Table 3.4
d = e2/(3.0*d0)
= 45[mm]/(3.0*22[mm])
= 0.682 [4]
Fb,Rd = (k1*b*fu*d*t)/M2
= (2.5*0.682*470[N/mm2]*20[mm]*9.6[mm])/1.25
= 123.055[kN] pt. 1-8 Table 3.4
z = zp + (n2 - 1)*p2/2
= 60[mm] + (1 - 1)*60[mm]/2
= 60[mm] SCI P358 p.115
IsSingleLineOfBoltsTrue
IsSingleLineOfBoltsTrue
IsSingleLineOfBoltsTrue
= (6*z)/(n1*(n1 + 1)*p1)
= (6*60[mm])/(6*(6 + 1)*70[mm])
= 0.122 SCI P358 p.115
Shear at gross section [KN] 829.29 280.00 UDL 0.34 pt. 1-1 Eq. 6.18
Av,DN = 0.9*(hb - dnt - dnb)*tw
= 0.9*(528.3[mm] - 30[mm] - 30[mm])*9.6[mm]
= 4046.11[mm2] SCI P358 p.18,
p.124
Vpl,Rd = Av*(fy/(3)0.5)/M0
= 4046.11[mm2]*(355[N/mm2]/(3)0.5)/1
= 829.288[kN] pt. 1-1 Eq. 6.18
Shear at net section [KN] 603.26 280.00 UDL 0.46 SCI P358 p.121
Av,DN = 0.9*(hb - dnt - dnb)*tw
= 0.9*(528.3[mm] - 30[mm] - 30[mm])*9.6[mm]
= 4046.11[mm2] SCI P358 p.18,
p.124
Av,net = Av - n1*d0*tw
= 4046.11[mm2] - 6*22[mm]*9.6[mm]
= 2778.91[mm2] SCI P358 p.121
VRd,n = Av,net*fu/(3)0.5/M2
= 2778.91[mm2]*470[N/mm2]/(3)0.5/1.25
= 603.257[kN] SCI P358 p.121
Block tearing [KN] 628.33 280.00 UDL 0.45 pt. 1-8 Eq. 3.10
IsSingleLineOfBoltsTrue
Shear and bending interaction at the notch [KN*m] 124.57 32.20 UDL 0.26 SCI P358 p.18,
p.124,
pt. 1-1 Cl. 6.2.8
Av,DN = 0.9*(hb - dnt - dnb)*tw
= 0.9*(528.3[mm] - 30[mm] - 30[mm])*9.6[mm]
= 4046.11[mm2] SCI P358 p.18,
p.124
Vpl,DN,Rd = Av,DN*fy/((3.0)0.5*M0)
= 4046.11[mm2]*355[N/mm2]/((3.0)0.5*1)
= 829.288[kN] SCI P358 p.18,
p.124
VEd< = 0.5*Vpl,DN,Rd280[kN]<
= 0.5*829.288[kN]True
a = 0.7*s
= 0.7*10[mm]
= 7[mm] Sec. 4.5.2
= VEd/(2.0*a*Lw)
= 280[kN]/(2.0*7[mm]*450[mm])
= 44.444[N/mm2] pt. 1-8 Eq. 4.1
w = (
[N/mm2][N/mm2][N/mm2]
[N/mm2]
Support
Web or wall local shear with one beam [KN] 885.42 280.00 UDL 0.32 pt. 1-1 Eq. 6.18
Av = hp*t2
= 450[mm]*9.6[mm]
= 4320[mm2] SCI P358 p.128
Vpl,Rd = Av*(fy/(3)0.5)/M0
= 4320[mm2]*(355[N/mm2]/(3)0.5)/1
= 885.424[kN] pt. 1-1 Eq. 6.18
Web or wall punching shear [KN] 2030.40 280.00 UDL 0.14 SCI P358 p.128
Wpl = tp*hp2/6
= 16[mm]*450[mm]2/6
= 5.40E+05[mm3] [4]
z = zp + (n2 - 1)*p2/2
= 60[mm] + (1 - 1)*60[mm]/2
= 60[mm] SCI P358 p.115
VRd = (Wpl*fu*t2/tp)/(z*M2)
= (5.40E+05[mm3]*470[N/mm2]*9.6[mm]/16[mm])/(60[mm]*1.25)
= 2030.4[kN] SCI P358 p.128
M2 = Mu
= 1.1 SCI P358 p.4
Nu,Rd = 0.9*Anet*fu/M2
= 0.9*5088[mm2]*470[N/mm2]/1.1
= 1956.57[kN] pt. 1-1 Eq. 6.7
Block tearing due to tension [KN] 1962.10 0.00 UDL 0.00 pt. 1-8 Eq. 3.9
Ant = tp*((n1 - 1)*p1 - (n1 - 1)*d0)
= 16[mm]*((6 - 1)*70[mm] - (6 - 1)*22[mm])
= 3840[mm2] SCI P358 p.130
IsSingleLineOfBoltsTrue
M2 = Mu
= 1.1 SCI P358 p.4
IsSingleLineOfBoltsTrue
M2 = Mu
= 1.1 SCI P358 p.4
Bolt shear [KN] 640.92 0.00 UDL 0.00 pt. 1-8 Table 3.4
M2 = Mu
= 1.1 SCI P358 p.4
Fv,Rd = (v*fub*A)/M2
= (0.6*800[N/mm2]*244.794[mm2])/1.1
= 106.819[kN] pt. 1-8 Table 3.4
FRd = n*Fv,Rd
= 6*106.819[kN]
= 640.915[kN] pt. 1-8 Table 3.4
Bolt bearing due to tension [KN] 1864.46 0.00 UDL 0.00 pt. 1-8 Table 3.4
M2 = Mu
= 1.1 SCI P358 p.4
d = e2/(3.0*d0)
= 60[mm]/(3.0*22[mm])
= 0.909 [4]
Fb,Rd = (k1*b*fu*d*t)/M2
= (2.5*0.909*470[N/mm2]*20[mm]*16[mm])/1.1
= 310.744[kN] pt. 1-8 Table 3.4
FRd = n*Fb,Rd
= 6*310.744[kN]
= 1864.46[kN] pt. 1-8 Table 3.4
M2 = Mu
= 1.1 SCI P358 p.4
Nu,Rd = 0.9*Anet*fu/M2
= 0.9*3052.8[mm2]*470[N/mm2]/1.1
= 1173.94[kN] pt. 1-1 Eq. 6.7
Block tearing due to tension [KN] 1118.23 0.00 UDL 0.00 pt. 1-8 Eq. 3.9
Ant = tw*((n1 - 1)*p1 - (n1 - 1)*d0)
= 9.6[mm]*((6 - 1)*70[mm] - (6 - 1)*22[mm])
= 2304[mm2] SCI P358 p.131
IsSingleLineOfBoltsTrue
M2 = Mu
= 1.1 SCI P358 p.4
IsSingleLineOfBoltsTrue
M2 = Mu
= 1.1 SCI P358 p.4
Bolt bearing due to tension [KN] 839.01 0.00 UDL 0.00 pt. 1-8 Table 3.4
M2 = Mu
= 1.1 SCI P358 p.4
d = e2/(3.0*d0)
= 45[mm]/(3.0*22[mm])
= 0.682 [4]
Fb,Rd = (k1*b*fu*d*t)/M2
= (2.5*0.682*470[N/mm2]*20[mm]*9.6[mm])/1.1
= 139.835[kN] pt. 1-8 Table 3.4
FRd = n*Fb,Rd
= 6*139.835[kN]
= 839.008[kN] pt. 1-8 Table 3.4
WARNINGS
- Overall stability of the beam (lateral torsional buckling) should be checked while designing the member considering the reduction of area due to the
notch.
------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
NOTATION
a: Effective throat size of the weld, distance between the first line of bolts and the face of the support
A: Gross section area
Anet: Net area subjected to tension
Ant: Net area subjected to tension
Anv: Net area subjected to shear
Av : Shear area
Av,DN: Shear area at double notched beam
Av,net: Net shear area
: Fin plate bolt group factor
b: Bolt bearing resistance factor, Table 3.4
d: Bolt bearing resistance factor, Table 3.4
LT: Imperfection factor
v: Bolt shear resistance factor, Table 3.4
: Fin plate bolt group factor
w: Correlation factor taken from Table 4.1
d: Nominal bolt diameter
d0: Hole diameter
demin: Minimum edge distance
dnmin: Minimum notch depth
dnb: Bottom notch height
dnmax: Maximum notch height
dnt: Top notch height
e1: End distance
e2: Edge distance
Fb,Rd: Design bearing resistance per bolt
Fb,Rd,hor: Design bearing resistance per bolt in a horizontal direction
Fb,Rd,ver: Design bearing resistance per bolt in a vertical direction
FRd: Design resistance of the bolt group
fu: Ultimate tensile strength of the steel on which the bolt bears
fu: Ultimate tensile strength
fub: Ultimate tensile strength of the bolt
fu,p: Ultimate tensile strength of the bolt
fu: Nominal ultimate tensile strength of the weaker part joined
Fv,Rd: Design shear resistance per bolt
fvwd: Design shear strength of fillet welds
fy: Yield strength
fy,p: Yield strength of the plate material
gh: Horizontal gap between members
M0: Partial factor for resistance of cross-sections whatever the class is
M1: Partial factor for resistance of members to instability assessed by member checks
M2: Partial factor for resistance of cross-sections in tension to fracture
Mu: Partial factor for resistance of components when verifying structural integrity
hb: Height of the member
hp: Height of plate
HasDoubleNotch: Has double notch
Ibg: Moment of inertia of bolt group
IsSingleLineOfBolts: Single line of bolts
k 1: Bolt bearing factor
ktop: Thickness of the top flange + root radius
kbottom: Thickness of the bottom flange + root radius
: Factor to account for the triangular shape of the bending moment diagram in the fin plate
Lmax: Maximum length
Lmin: Minimum length
ln: Notch length
lnmax: Maximum notch length
Lw: Length of weld
LT: Non dimensional slenderness for lateral-torsional buckling
LT: Reduction factor for lateral-torsional buckling
Mb,Rd: Design buckling resistance moment
Mc,Rd: Design resistance for bending about one principal axis of a cross-section
MEd: Design moment
Mv,DN,Rd: Moment resistance of a double notched beam at the notch
n: Total number of bolts
n1: Number of horizontal bolt rows
n2: Number of vertical bolt rows
Nu,Rd: Design ultimate resistance of the net section at holes
p1: Vertical spacing between centres of bolts in a line in the load direction
p2: Horizontal spacing between centres of bolts in adjacent lines perpendicular to the load direction
pmax: Maximum bolts spacing
LT: Value to determine lateral-torsional buckling reduction factor
rb : Root radius of the beam section
rs : Root radius of the support section
s: Weld size
REFERENCES
[1] Joints in Steel Construction – Simple Joints to Eurocode 3 (P358), SCI and BCSA, 2011.
[4] SN017 NCCI: Shear resistance of a fin plate connection.
AECOM
Current Date: 1/6/2022 7:18 PM
Units system: SI
File name: C:\Users\sujeevanleonard.tham\OneDrive - AECOM\Projects\J110\J110\OneDrive_2021-07-01\12. Southern Staircase\Design
Files\Str\Connection Design\B50A TO NEW RC BEAM.rcnx
Steel connections
Results
____________________________________________________________________________________________________________________________
___________________________________________________________________________________
DEMANDS
Description Pu Mu22 Mu33 Vu2 Vu3
[kN] [kN*m] [kN*m] [kN] [kN]
----------------------------------------------------------------------------------------------
UDL 0.00 0.00 0.00 150.00 0.00
----------------------------------------------------------------------------------------------
Distance from fasteners to edge [mm] 50.00 24.00 -- pt. 1-8 Table 3.3
e2min = 1.2*d0
= 1.2*20[mm]
= 24[mm] pt. 1-8 Table 3.3
Column
Effective weld throat thickness [mm] 7.00 3.00 -- Sec. 4.5.2
a = 0.7*s
= 0.7*10[mm]
= 7[mm] Sec. 4.5.2
----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
DESIGN CHECK
Verification Unit Capacity Demand Ctrl EQ Ratio References
------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Concrete base
Concrete base bearing of the effective area [KN] 11333.33 0.00 UDL 0.00 DG1 Sec 3.1.1;
Ac1 = ((bp/hp)*Ncs)*Ncs
= ((300[mm]/600[mm])*600[mm])*600[mm]
= 1.80E+05[mm2] DG1 Sec 3.1.1
Ac0 = hp*bp
= 300[mm]*600[mm]
= 1.80E+05[mm2]
i = 2.0/3.0
= (LoadedAreaRatio)1/2
= (1)1/2
=1
fcd = cc*fck/c
= 0.85*30[N/mm2]/1.5
= 17[N/mm2]
fjd = i**fcd
= 0.667*1*17[N/mm2]
= 11.333[N/mm2]
Base plate
Yielding at bearing interface [KN*m/m] 15.15 0.00 UDL 0.00 SCI P358 p.231
MRd = fyp*tp2/(6.0*M0)
= 355[N/mm2]*16[mm]2/(6.0*1)
= 15.147[kN*m/m] SCI P358 p.231
Yielding at tension interface [KN*m/m] 22.72 0.00 UDL 0.00 DG1 Eq. 3.3.13
MRd = fyp*tp2.0/4.0/M0
= 355[N/mm2]*16[mm]2.0/4.0/1
= 22.72[kN*m/m] DG1 Eq. 3.3.13
MEd = Mstrip/beff
= 0[kN*m]/32.96[mm]
= 0[kN*m/m]
Column
Weld resistance [KN/m] 2068.33 0.00 UDL 0.00 Eq. 4.3
fvwd = (fu/3.0(1.0/2.0))/(w*M2)
= (470[N/mm2]/3.0(1.0/2.0))/(0.9*1.25)
= 241.204[N/mm2] pt. 1-8 Eq. 4.4
a = 0.7*s
= 0.7*10[mm]
= 7[mm] Sec. 4.5.2
Fw,Rd = fvwd*a*K
= 241.204[N/mm2]*7[mm]*1.225
= 2.068[kN/mm] Eq. 4.3
------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Ratio 0.00
------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Distance from fasteners to edge [mm] 50.00 24.00 -- pt. 1-8 Table 3.3
e2min = 1.2*d0
= 1.2*20[mm]
= 24[mm] pt. 1-8 Table 3.3
Column
----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
DESIGN CHECK
Verification Unit Capacity Demand Ctrl EQ Ratio References
------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Concrete base
Concrete base bearing of the effective area [KN] 11333.33 0.00 UDL 0.00 DG1 Sec 3.1.1;
Ac1 = ((bp/hp)*Ncs)*Ncs
= ((300[mm]/600[mm])*600[mm])*600[mm]
= 1.80E+05[mm2] DG1 Sec 3.1.1
Ac0 = hp*bp
= 300[mm]*600[mm]
= 1.80E+05[mm2]
i = 2.0/3.0
= (LoadedAreaRatio)1/2
= (1)1/2
=1
fcd = cc*fck/c
= 0.85*30[N/mm2]/1.5
= 17[N/mm2]
fjd = i**fcd
= 0.667*1*17[N/mm2]
= 11.333[N/mm2]
Base plate
Yielding at bearing interface [KN*m/m] 15.15 0.00 UDL 0.00 SCI P358 p.231
MRd = fyp*tp2/(6.0*M0)
= 355[N/mm2]*16[mm]2/(6.0*1)
= 15.147[kN*m/m] SCI P358 p.231
Yielding at tension interface [KN*m/m] 22.72 0.00 UDL 0.00 DG1 Eq. 3.3.13
MRd = fyp*tp2.0/4.0/M0
= 355[N/mm2]*16[mm]2.0/4.0/1
= 22.72[kN*m/m] DG1 Eq. 3.3.13
MEd = Mstrip/beff
= 0[kN*m]/32.96[mm]
= 0[kN*m/m]
Column
Weld resistance [KN/m] 2068.33 0.00 UDL 0.00 Eq. 4.3
fvwd = (fu/3.0(1.0/2.0))/(w*M2)
= (470[N/mm2]/3.0(1.0/2.0))/(0.9*1.25)
= 241.204[N/mm2] pt. 1-8 Eq. 4.4
a = 0.7*s
= 0.7*10[mm]
= 7[mm] Sec. 4.5.2
Fw,Rd = fvwd*a*K
= 241.204[N/mm2]*7[mm]*1.225
= 2.068[kN/mm] Eq. 4.3
------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Ratio 0.00
------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Major axis
Fasteners
Dimensions
Dimensions Unit Value Min. value Max. value Sta. References
----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Fasteners
DESIGN CHECK
Verification Unit Capacity Demand Ctrl EQ Ratio References
------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Steel failure of fastener in tension [KN] 130.65 0.00 UDL 0.00 [8],
EN 1992-4: 2013,
Table 7.1
As = π/4.0*(d - 0.9743 [in]/nt)2
= π/4.0*(20[mm] - 0.9743 [in]/10.58)2
= 244.973[mm2]
NRk,s = As*fuk
= 244.973[mm2]*800[N/mm2]
= 195.978[kN] [8]
NRd,s = NRk,s/Ms
= 195.978[kN]/1.5
= 130.652[kN] EN 1992-4: 2013,
Table 7.1
Pull-out failure of single fastener [KN] 89.06 0.00 UDL 0.00 EN 1992-4: 2013,
Eq. 7.1,
EN 1992-4: 2013,
Table 7.1
Ah = π*((dh)2 - d2)/4.0
= π*((34[mm])2 - 20[mm]2)/4.0
= 593.761[mm2]
CrackedConcreteTrue
NRk,p = k1*Ah*fck
= 7.5*593.761[mm2]*30[N/mm2]
= 133.596[kN] EN 1992-4: 2013,
Eq. 7.1
NRd,p = NRk,p/Mp
= 133.596[kN]/1.5
= 89.064[kN] EN 1992-4: 2013,
Table 7.1
Steel failure of fastener in shear [KN] 78.39 25.00 UDL 0.32 EN 1992-4: 2013,
Sec. 7.2.2.3.1
fuk>500.0 [MPa]800[N/mm2]>500.0 [MPa]True
VRk,s = k50*As*fuk
= 0.5*244.973[mm2]*800[N/mm2]
= 97.989[kN]
DuctileSteelTrue
VRd,s = VRk,s/Ms
= 97.989[kN]/1.25
= 78.391[kN]
Pry-out failure of single fastener [KN] 49.02 25.00 UDL 0.51 EN 1992-4: 2013,
Eq. 7.13,
EN 1992-4: 2013,
Table 7.1
HasSupplementaryReinforcementTrue
c1Left<1.5*hef1350[mm]<1.5*200[mm]False
c1Left = 1.5*hef
= 1.5*200[mm]
= 300[mm] EN 1992-4: 2013,
Fig. 7.4
c1Left<1.5*hef1150[mm]<1.5*200[mm]False
c1Left = 1.5*hef
= 1.5*200[mm]
= 300[mm] EN 1992-4: 2013,
Fig. 7.4
c1Left<1.5*hef100[mm]<1.5*200[mm]True
c1Left = c1Left
= 100[mm] EN 1992-4: 2013,
Fig. 7.4
c1Left<1.5*hef800[mm]<1.5*200[mm]False
c1Left = 1.5*hef
= 1.5*200[mm]
= 300[mm] EN 1992-4: 2013,
Fig. 7.4
IsCloseToThreeEdgesFalse
hef = hef
= 200[mm] EN 1992-4: 2013,
Sec. 7.2.1.6
ccr,N = 1.5*hef
= 1.5*200[mm]
= 300[mm] EN 1992-4: 2013,
Sec. 7.2.1.6
A0c,N = 9.0*hef2.0
= 9.0*200[mm]2.0
= 3.60E+05[mm2] EN 1992-4: 2013,
Eq. 7.15
d = t - Cover - dre/2.0
= 400[mm] - 70[mm] - 10[mm]/2.0
= 325[mm] EN 1992-4: 2013,
Sec. 6.4.3
z = 0.85*d
= 0.85*200[mm]
= 170[mm] EN 1992-4: 2013,
Sec. 6.4.3
ExistEffectOfCompressionForceFalse
CrackedConcreteTrue
NRk,c = N0Rk,c*Ac,N/A0c,N*s,N*re,N*ec,N*M,N
= 137.878[kN]*2.40E+05[mm2]/3.60E+05[mm2]*0.8*1*1*1
= 73.535[kN] EN 1992-4: 2013,
Eq. 7.13
VRk,cp = k3*NRk,c
= 1*73.535[kN]
= 73.535[kN]
NRd,c = NRk,c/Mc
= 73.535[kN]/1.5
= 49.023[kN] EN 1992-4: 2013,
Table 7.1
Steel failure of shear supplementary reinforcement [KN] 178.16 45.12 UDL 0.25 EN 1992-4: 2013,
Eq. 7.50,
EN 1992-4: 2013,
Table 7.1
SurfaceReinforcementFalse
NRk,re = k6*nre*As,re*fyk
= 0.5*3*314[mm2]*435[N/mm2]
= 204.885[kN] EN 1992-4: 2013,
Eq. 7.50
NRd,re = NRk,re/Ms
= 204.885[kN]/1.15
= 178.161[kN] EN 1992-4: 2013,
Table 7.1
es = Cover + tgrout + t
= 70[mm] + 50.8[mm] + 16[mm]
= 136.8[mm]
d = t - Cover - dre/2.0
= 400[mm] - 70[mm] - 10[mm]/2.0
= 325[mm] EN 1992-4: 2013,
Sec. 6.4.3
z = 0.85*d
= 0.85*200[mm]
= 170[mm] EN 1992-4: 2013,
Sec. 6.4.3
------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Ratio 0.51
------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Minor axis
Fasteners
Dimensions
Dimensions Unit Value Min. value Max. value Sta. References
----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Fasteners
DESIGN CHECK
Verification Unit Capacity Demand Ctrl EQ Ratio References
------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Steel failure of fastener in tension [KN] 130.65 0.00 UDL 0.00 [8],
EN 1992-4: 2013,
Table 7.1
As = π/4.0*(d - 0.9743 [in]/nt)2
= π/4.0*(20[mm] - 0.9743 [in]/10.58)2
= 244.973[mm2]
NRk,s = As*fuk
= 244.973[mm2]*800[N/mm2]
= 195.978[kN] [8]
NRd,s = NRk,s/Ms
= 195.978[kN]/1.5
= 130.652[kN] EN 1992-4: 2013,
Table 7.1
Pull-out failure of single fastener [KN] 89.06 0.00 UDL 0.00 EN 1992-4: 2013,
Eq. 7.1,
EN 1992-4: 2013,
Table 7.1
Ah = π*((dh)2 - d2)/4.0
= π*((34[mm])2 - 20[mm]2)/4.0
= 593.761[mm2]
CrackedConcreteTrue
NRk,p = k1*Ah*fck
= 7.5*593.761[mm2]*30[N/mm2]
= 133.596[kN] EN 1992-4: 2013,
Eq. 7.1
NRd,p = NRk,p/Mp
= 133.596[kN]/1.5
= 89.064[kN] EN 1992-4: 2013,
Table 7.1
Steel failure of fastener in shear [KN] 78.39 0.00 UDL 0.00 EN 1992-4: 2013,
Sec. 7.2.2.3.1
fuk>500.0 [MPa]800[N/mm2]>500.0 [MPa]True
VRk,s = k50*As*fuk
= 0.5*244.973[mm2]*800[N/mm2]
= 97.989[kN]
DuctileSteelTrue
VRd,s = VRk,s/Ms
= 97.989[kN]/1.25
= 78.391[kN]
Steel failure of shear supplementary reinforcement [KN] 59.39 0.00 UDL 0.00 EN 1992-4: 2013,
Eq. 7.50,
EN 1992-4: 2013,
Table 7.1
SurfaceReinforcementFalse
k6 = 0.5 EN 1992-4: 2013,
Sec. 7.2.2.6
NRk,re = k6*nre*As,re*fyk
= 0.5*1*314[mm2]*435[N/mm2]
= 68.295[kN] EN 1992-4: 2013,
Eq. 7.50
NRd,re = NRk,re/Ms
= 68.295[kN]/1.15
= 59.387[kN] EN 1992-4: 2013,
Table 7.1
es = Cover + tgrout + t
= 70[mm] + 50.8[mm] + 16[mm]
= 136.8[mm]
d = t - Cover - dre/2.0
= 400[mm] - 70[mm] - 10[mm]/2.0
= 325[mm] EN 1992-4: 2013,
Sec. 6.4.3
z = 0.85*d
= 0.85*325[mm]
= 276.25[mm] EN 1992-4: 2013,
Sec. 6.4.3
------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Ratio 0.00
------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Biaxial
Maximum compression and tension (UDL)
----------------------------------------------------------------------------------
Maximum bearing pressure 0.00 [N/mm2]
Minimum bearing pressure 0.00 [N/mm2]
Maximum anchor tension 0.00 [kN]
Minimum anchor tension 0.00 [kN]
Neutral axis angle 0.00 [deg]
Bearing length 1E33 [mm]
----------------------------------------------------------------------------------
Anchors tensions
Anchor Transverse Longitudinal Shear Tension
[mm] [mm] [kN] [kN]
---------------------------------------------------------------------------------------------
1 -100.00 0.00 25.00 0.00
2 100.00 0.00 25.00 0.00
3 100.00 200.00 25.00 0.00
4 100.00 -200.00 25.00 0.00
5 -100.00 200.00 25.00 0.00
6 -100.00 -200.00 25.00 0.00
---------------------------------------------------------------------------------------------
Major axis
Minor axis
NOTATION
a: Effective throat size of the weld, distance between the first line of bolts and the face of the support
w: Correlation factor taken from Table 4.1
d0: Hole diameter
e2min: Minimum vertical edge distance
fu: Ultimate tensile strength of the steel on which the bolt bears
fvwd: Design shear strength of fillet welds
Fw,Rd: Design weld resistance per unit length
M2: Partial factor for resistance of cross-sections in tension to fracture
K: Weld force angle factor
s: Weld size
Ac0: Loaded area
Ac1: Maximum design distribution area
: Coefficient for difussion of the concentrated force
cc: Concrete compressive strength factor
beff: Effective width
bp: Base plate width
i: Bearing strength factor
fcd: Design value of concrete compressive strength
fck: Concrete cylinder strength
fjd: Design bearing strength
fyp: Yield strength of the plate
c: Material factor for concrete
M0: Partial factor for steel resistance
hc: Column depth
hp: Base plate height
LoadedAreaRatio: Distributed to loaded area ratio
s: Weld size
tp: Base plate thickness
MRd: Unitary bending design resistance
Mstrip: Maximum bending moment at the strip
MEd: Unitary design moment
Ncs: Length of the concrete supporting surface or pier parallel to moment design direction
hpmin: Minimum base plate heigth
bpmin: Minimum base plate width
Ac,N: Actual projected area
Ah: Load bearing area of the head of the fastener
As: Fastener effective area for tension and shear
As,re: Cross section of one leg of the supplementary reinforcement
A0c,N: Reference projected area
c: Edge distance from an axis of a fastener
c 1: Edge distance in direction 1
c1Left: Distance from the fastener center to the left edge of the concrete base
c1Right: Distance from the fastener center to the right edge of the concrete base
c2Bot: Distance from the fastener center to the bottom edge of the concrete base
c2Top: Distance from the fastener center to the top edge of the concrete base
ccr,N: Characteristic edge distance
CrackedConcrete: Concrete is cracked
d: Nominal fastener diameter
dh: Diameter of fastener head
DuctileSteel: Flag to indicate tha the steel is ductile
ExistEffectOfCompressionForce: Compression force between fixture and concrete exists
fck: Characteristic cube strength of the concrete strength class
fuk: Characteristic steel yield strength
fyk: Characteristic steel ultimate tensile strength
Mc: Partial factor for concrete
Mp: Partial factor for pull out failure
Ms: Partial factor for steel
hef: Effective embedment depth
HasSupplementaryReinforcement: Flag to indicate that the concrete base has supplementary reinforcement
IsCloseToThreeEdges: Flag to indicate that the fastener or group of fasteners are close to three or more edges
k 1: Pull-out failure factor
k 3: Pry-out failure factor
k50: Shear steel failure factor
k51: Non-ductile steel factor
k 6: Efficiency factor
k 9: Concrete cone failure factor
NRd,c: Design resistance of a fasterner or group of fastener for concrete cone failure
NRd,p: Design resistance for pull out failure
NRd,re: Supplentary reinforcement design resistance for steel failure
NRd,s: Design resistance for steel failure
nre: Number of legs of supplementary reinforcement effective for one fastener
NRk,c: Characteristic resistance of a fasterner or group of fastener for concrete cone failure
NRk,p: Characteristic resistance for pull out failure
NRk,s: Characteristic resistance of a single fastener for tensile steel failure
NRk,re: Supplentary reinforcement characteristic resistance for steel failure
nt: Number of threads per inch
N0Rk,c: Characteristic resistance of a single fasterner for concrete cone failure
ec,N: Load eccentricity factor
M,N: Factor that takes into account the effect of a compression force between fixture and concrete
re,N: Shell spalling factor
s,N: Stress distribution factor
SurfaceReinforcement: Flag to indicate surface supplementary reinforcement
t: Base plate thickness
tgrout: Grout layer thickness
VEd: Design value of resultant shear force
VRd,s: Design resistance of a single fastener for shear steel failure
VRk,cp: Characteristic resistance for pry-out failure
VRk,s: Characteristic resistance of a single fastener for shear steel failure
z: Internal lever arm calculated according to the theory of elasticity
d: Concrete base effective depth
Cover: Concrete cover
dre: Reinforcement diameter
NEd,re: Design value of tension load acting on the supplementary reinforcement
es: Distance between reinforcement and shear force acting on a fixture
smin: Fastener minimum spacing
REFERENCES
[8] International Federation for Structural Concrete (2011). Design of Anchorages in Concrete. CEP-FIP. Lousanne, Switzerland.
Current Date: 1/6/2022 6:31 PM
Units system: SI
File name: C:\Users\sujeevanleonard.tham\OneDrive - AECOM\Projects\J110\J110\OneDrive_2021-07-01\12. Southern Staircase\Design
Files\Str\Connection Design\B25A TO B25A.rcnx
Steel connections
Results
____________________________________________________________________________________________________________________________
___________________________________________________________________________________
DEMANDS
Description Pu Ru RuLeft Mu Mmax C1
[kN] [kN] [kN] [kN*m] [kN*m]
----------------------------------------------------------------------------------------
UDL 0.00 50.00 50.00 0.00 0.00 0.00
----------------------------------------------------------------------------------------
GEOMETRIC CONSIDERATIONS
Dimensions Unit Value Min. value Max. value Sta. References
----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Fin plate
Lmin = 0.6*hb
= 0.6*256[mm]
= 153.6[mm] [1]
Lmin = 0.6*hb
= 0.6*256[mm]
= 153.6[mm] [1]
demin = 2*d
= 2*16[mm]
= 32[mm] [1]
demin = 2*d
= 2*16[mm]
= 32[mm] [1]
p1 = 2.2*d0
= 2.2*18[mm]
= 39.6[mm] pt. 1-8 Table 3.3
a = 0.7*s
= 0.7*8[mm]
= 5.6[mm] Sec. 4.5.2
Beam
tp = 0.42*d
= 0.42*16[mm]
= 6.72[mm] [1]
HasDoubleNotch → True
dnmax = hb/5
= 256[mm]/5
= 51.2[mm] [1]
lnmax = hb
= 256[mm] [1]
HasDoubleNotch → True
dnmax = hb/5
= 256[mm]/5
= 51.2[mm] [1]
lnmax = hb
= 256[mm] [1]
demin = 2*d
= 2*16[mm]
= 32[mm] [1]
demin = 2*d
= 2*16[mm]
= 32[mm] [1]
----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
DESIGN CHECK
Verification Unit Capacity Demand Ctrl EQ Ratio References
------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Plate (beam side)
Bolt group shear [KN] 112.75 50.00 UDL 0.44 pt. 1-8 Table 3.4,
SCI P358 p.115
Fv,Rd = (αv*fub*A)/γM2
= (0.6*800[N/mm2]*156.668[mm2])/1.25
= 60.161[kN] pt. 1-8 Table 3.4
z = zp + (n2 - 1)*p2/2
= 50[mm] + (1 - 1)*60[mm]/2
= 50[mm] SCI P358 p.115
IsSingleLineOfBolts → True
IsSingleLineOfBolts → True
IsSingleLineOfBolts → True
β = (6*z)/(n1*(n1 + 1)*p1)
= (6*50[mm])/(3*(3 + 1)*60[mm])
= 0.417 SCI P358 p.115
Bolt group bearing [KN] 236.33 50.00 UDL 0.21 pt. 1-8 Table 3.4,
SCI P358 p.116
IsSingleLineOfBolts → True
αd = e1/(3.0*d0)
= 40[mm]/(3.0*18[mm])
= 0.741 pt. 1-8 Table 3.4
αd = p1/(3.0*d0) - 1.0/4.0
= 60[mm]/(3.0*18[mm]) - 1.0/4.0
= 0.861 pt. 1-8 Table 3.4
Fb,Rd = (k1*αb*fu*d*t)/γM2
= (2.5*0.741*470[N/mm2]*16[mm]*10[mm])/1.25
= 111.407[kN] pt. 1-8 Table 3.4
αd = e2/(3.0*d0)
= 50[mm]/(3.0*18[mm])
= 0.926 [4]
Fb,Rd = (k1*αb*fu*d*t)/γM2
= (2.5*0.926*470[N/mm2]*16[mm]*10[mm])/1.25
= 139.259[kN] pt. 1-8 Table 3.4
z = zp + (n2 - 1)*p2/2
= 50[mm] + (1 - 1)*60[mm]/2
= 50[mm] SCI P358 p.115
IsSingleLineOfBolts → True
IsSingleLineOfBolts → True
IsSingleLineOfBolts → True
β = (6*z)/(n1*(n1 + 1)*p1)
= (6*50[mm])/(3*(3 + 1)*60[mm])
= 0.417 SCI P358 p.115
Vpl,Rd = Av*(fy/(3)0.5)/γM0/1.27
= 2000[mm2]*(355[N/mm2]/(3)0.5)/1/1.27
= 322.771[kN] [4]
VRd,n = Av,net*fu,p/(3)0.5/γM2
= 1460[mm2]*470[N/mm2]/(3)0.5/1.25
= 316.942[kN] [4]
Block tearing [KN] 312.78 50.00 UDL 0.16 pt. 1-8 Eq. 3.10
IsSingleLineOfBolts → True
Lateral torsional buckling [KN] 473.33 50.00 UDL 0.11 pt. 1-1 Eq. 6.55,
pt. 1-1 Eq. 6.13,
SCI P358 p.119
κ = 0.6 SCI P358 p.119
Wpl = tp*hp2/6
= 10[mm]*200[mm]2/6
= 66666.67[mm3] [4]
λLT = 2.8/86.8*((zp*hp)/(1.5*tp2))0.5
= 2.8/86.8*((50[mm]*200[mm])/(1.5*10[mm]2))0.5
= 0.263 SCI P358 p.119
Mb,Rd = χLT*Wpl*fy/γM1
= 0.951*66666.67[mm3]*355[N/mm2]/1
= 22.506[kN*m] pt. 1-1 Eq. 6.55
Mc,Rd = Wpl*fy/γM0
= 66666.67[mm3]*355[N/mm2]/1
= 23.667[kN*m] pt. 1-1 Eq. 6.13
z = zp + (n2 - 1)*p2/2
= 50[mm] + (1 - 1)*60[mm]/2
= 50[mm] SCI P358 p.115
VRd = Mc,Rd/z
= 23.667[kN*m]/50[mm]
= 473.333[kN] SCI P358 p.119
Beam
Bolt bearing [KN] 123.51 50.00 UDL 0.40 pt. 1-8 Table 3.4,
SCI P358 p.116
IsSingleLineOfBolts → True
αd = e1/(3.0*d0)
= 43[mm]/(3.0*18[mm])
= 0.796 pt. 1-8 Table 3.4
αd = p1/(3.0*d0) - 1.0/4.0
= 60[mm]/(3.0*18[mm]) - 1.0/4.0
= 0.861 pt. 1-8 Table 3.4
Fb,Rd = (k1*αb*fu*d*t)/γM2
= (2.5*0.796*470[N/mm2]*16[mm]*6.3[mm])/1.25
= 75.451[kN] pt. 1-8 Table 3.4
αd = e2/(3.0*d0)
= 35[mm]/(3.0*18[mm])
= 0.648 [4]
Fb,Rd = (k1*αb*fu*d*t)/γM2
= (2.5*0.648*470[N/mm2]*16[mm]*6.3[mm])/1.25
= 61.413[kN] pt. 1-8 Table 3.4
z = zp + (n2 - 1)*p2/2
= 50[mm] + (1 - 1)*60[mm]/2
= 50[mm] SCI P358 p.115
IsSingleLineOfBolts → True
IsSingleLineOfBolts → True
IsSingleLineOfBolts → True
β = (6*z)/(n1*(n1 + 1)*p1)
= (6*50[mm])/(3*(3 + 1)*60[mm])
= 0.417 SCI P358 p.115
Shear at gross section [KN] 239.40 50.00 UDL 0.21 pt. 1-1 Eq. 6.18
Av,DN = 0.9*(hb - dnt - dnb)*tw
= 0.9*(256[mm] - 25[mm] - 25[mm])*6.3[mm]
= 1168.02[mm2] SCI P358 p.18,
p.124
Vpl,Rd = Av*(fy/(3)0.5)/γM0
= 1168.02[mm2]*(355[N/mm2]/(3)0.5)/1
= 239.397[kN] pt. 1-1 Eq. 6.18
Shear at net section [KN] 179.71 50.00 UDL 0.28 SCI P358 p.121
Av,DN = 0.9*(hb - dnt - dnb)*tw
= 0.9*(256[mm] - 25[mm] - 25[mm])*6.3[mm]
= 1168.02[mm2] SCI P358 p.18,
p.124
Av,net = Av - n1*d0*tw
= 1168.02[mm2] - 3*18[mm]*6.3[mm]
= 827.82[mm2] SCI P358 p.121
VRd,n = Av,net*fu/(3)0.5/γM2
= 827.82[mm2]*470[N/mm2]/(3)0.5/1.25
= 179.706[kN] SCI P358 p.121
Block tearing [KN] 183.16 50.00 UDL 0.27 pt. 1-8 Eq. 3.10
IsSingleLineOfBolts → True
Shear and bending interaction at the notch [KN*m] 15.82 4.50 UDL 0.28 SCI P358 p.18,
p.124,
pt. 1-1 Cl. 6.2.8
Av,DN = 0.9*(hb - dnt - dnb)*tw
= 0.9*(256[mm] - 25[mm] - 25[mm])*6.3[mm]
= 1168.02[mm2] SCI P358 p.18,
p.124
Vpl,DN,Rd = Av,DN*fy/((3.0)0.5*γM0)
= 1168.02[mm2]*355[N/mm2]/((3.0)0.5*1)
= 239.397[kN] SCI P358 p.18,
p.124
a = 0.7*s
= 0.7*8[mm]
= 5.6[mm] Sec. 4.5.2
τ|| = VEd/(2.0*a*Lw)
= 50[kN]/(2.0*5.6[mm]*200[mm])
= 22.321[N/mm2] pt. 1-8 Eq. 4.1
Support
Web or wall punching shear [KN] 315.84 50.00 UDL 0.16 SCI P358 p.128
Wpl = tp*hp2/6
= 10[mm]*200[mm]2/6
= 66666.67[mm3] [4]
z = zp + (n2 - 1)*p2/2
= 50[mm] + (1 - 1)*60[mm]/2
= 50[mm] SCI P358 p.115
VRd = (Wpl*fu*t2/tp)/(z*γM2)
= (66666.67[mm3]*470[N/mm2]*6.3[mm]/10[mm])/(50[mm]*1.25)
= 315.84[kN] SCI P358 p.128
Web local shear with beams in both sides [KN] 258.25 26.67 UDL 0.10 pt. 1-1 Eq. 6.18
hpmin = Min(hp1, hp2)
= Min(200[mm], 3000[mm])
= 200[mm] SCI P358 p.129
Av = hpmin*t2
= 200[mm]*6.3[mm]
= 1260[mm2] SCI P358 p.129
Vpl,Rd = Av*(fy/(3)0.5)/γM0
= 1260[mm2]*(355[N/mm2]/(3)0.5)/1
= 258.249[kN] pt. 1-1 Eq. 6.18
VEd,tot/2 = VEd,tot/2
= 53.333[kN]/2
= 26.667[kN] SCI P358 p.129
γM2 = γMu
= 1.1 SCI P358 p.4
Nu,Rd = 0.9*Anet*fu/γM2
= 0.9*1460[mm2]*470[N/mm2]/1.1
= 561.436[kN] pt. 1-1 Eq. 6.7
Block tearing due to tension [KN] 526.98 0.00 UDL 0.00 pt. 1-8 Eq. 3.9
Ant = tp*((n1 - 1)*p1 - (n1 - 1)*d0)
= 10[mm]*((3 - 1)*60[mm] - (3 - 1)*18[mm])
= 840[mm2] SCI P358 p.130
IsSingleLineOfBolts → True
γM2 = γMu
= 1.1 SCI P358 p.4
IsSingleLineOfBolts → True
γM2 = γMu
= 1.1 SCI P358 p.4
Bolt shear [KN] 205.09 0.00 UDL 0.00 pt. 1-8 Table 3.4
γM2 = γMu
= 1.1 SCI P358 p.4
Fv,Rd = (αv*fub*A)/γM2
= (0.6*800[N/mm2]*156.668[mm2])/1.1
= 68.364[kN] pt. 1-8 Table 3.4
FRd = n*Fv,Rd
= 3*68.364[kN]
= 205.093[kN] pt. 1-8 Table 3.4
Bolt bearing due to tension [KN] 474.75 0.00 UDL 0.00 pt. 1-8 Table 3.4
γM2 = γMu
= 1.1 SCI P358 p.4
αd = e2/(3.0*d0)
= 50[mm]/(3.0*18[mm])
= 0.926 [4]
Fb,Rd = (k1*αb*fu*d*t)/γM2
= (2.5*0.926*470[N/mm2]*16[mm]*10[mm])/1.1
= 158.249[kN] pt. 1-8 Table 3.4
FRd = n*Fb,Rd
= 3*158.249[kN]
= 474.747[kN] pt. 1-8 Table 3.4
γM2 = γMu
= 1.1 SCI P358 p.4
Nu,Rd = 0.9*Anet*fu/γM2
= 0.9*919.8[mm2]*470[N/mm2]/1.1
= 353.705[kN] pt. 1-1 Eq. 6.7
Block tearing due to tension [KN] 293.26 0.00 UDL 0.00 pt. 1-8 Eq. 3.9
Ant = tw*((n1 - 1)*p1 - (n1 - 1)*d0)
= 6.3[mm]*((3 - 1)*60[mm] - (3 - 1)*18[mm])
= 529.2[mm2] SCI P358 p.131
IsSingleLineOfBolts → True
γM2 = γMu
= 1.1 SCI P358 p.4
IsSingleLineOfBolts → True
γM2 = γMu
= 1.1 SCI P358 p.4
αd = e2/(3.0*d0)
= 35[mm]/(3.0*18[mm])
= 0.648 [4]
Fb,Rd = (k1*αb*fu*d*t)/γM2
= (2.5*0.648*470[N/mm2]*16[mm]*6.3[mm])/1.1
= 69.788[kN] pt. 1-8 Table 3.4
FRd = n*Fb,Rd
= 3*69.788[kN]
= 209.364[kN] pt. 1-8 Table 3.4
AECOM
Current Date: 1/6/2022 6:40 PM
Units system: SI
File name: C:\Users\sujeevanleonard.tham\OneDrive - AECOM\Projects\J110\J110\OneDrive_2021-07-01\12. Southern Staircase\Design
Files\Str\Connection Design\B25A TO B40B.rcnx
Steel connections
Results
____________________________________________________________________________________________________________________________
___________________________________________________________________________________
DEMANDS
Description Pu Ru RuLeft Mu Mmax C1
[kN] [kN] [kN] [kN*m] [kN*m]
-----------------------------------------------------------------------------------------------------------
UDL 0.00 70.00 70.00 0.00 0.00 0.00
-----------------------------------------------------------------------------------------------------------
GEOMETRIC CONSIDERATIONS
Dimensions Unit Value Min. value Max. value Sta. References
----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Fin plate
Length [mm] 200.00 153.60 212.50 [1]
Lmin = 0.6*hb
= 0.6*256[mm]
= 153.6[mm] [1]
Lmin = 0.6*hb
= 0.6*256[mm]
= 153.6[mm] [1]
Vertical center-to-center spacing (pitch) [mm] 60.00 39.60 140.00 pt. 1-8 Table 3.3
p1 = 2.2*d0
= 2.2*18[mm]
= 39.6[mm] pt. 1-8 Table 3.3
Beam
Thickness [mm] 6.30 -- 6.72 [1]
tp = 0.42*d
= 0.42*16[mm]
= 6.72[mm] [1]
HasDoubleNotchFalse
dnmax = hb/2
= 256[mm]/2
= 128[mm] [1]
lnmax = hb
= 256[mm] [1]
----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
DESIGN CHECK
Verification Unit Capacity Demand Ctrl EQ Ratio References
------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Plate (beam side)
Bolt group shear [KN] 112.75 70.00 UDL 0.62 pt. 1-8 Table 3.4,
SCI P358 p.115
Fv,Rd = (v*fub*A)/M2
= (0.6*800[N/mm2]*156.668[mm2])/1.25
= 60.161[kN] pt. 1-8 Table 3.4
z = zp + (n2 - 1)*p2/2
= 50[mm] + (1 - 1)*60[mm]/2
= 50[mm] SCI P358 p.115
IsSingleLineOfBoltsTrue
IsSingleLineOfBoltsTrue
IsSingleLineOfBoltsTrue
= (6*z)/(n1*(n1 + 1)*p1)
= (6*50[mm])/(3*(3 + 1)*60[mm])
= 0.417 SCI P358 p.115
Bolt group bearing [KN] 236.33 70.00 UDL 0.30 pt. 1-8 Table 3.4,
SCI P358 p.116
IsSingleLineOfBoltsTrue
d = e1/(3.0*d0)
= 40[mm]/(3.0*18[mm])
= 0.741 pt. 1-8 Table 3.4
d = p1/(3.0*d0) - 1.0/4.0
= 60[mm]/(3.0*18[mm]) - 1.0/4.0
= 0.861 pt. 1-8 Table 3.4
Fb,Rd = (k1*b*fu*d*t)/M2
= (2.5*0.741*470[N/mm2]*16[mm]*10[mm])/1.25
= 111.407[kN] pt. 1-8 Table 3.4
d = e2/(3.0*d0)
= 50[mm]/(3.0*18[mm])
= 0.926 [4]
Fb,Rd = (k1*b*fu*d*t)/M2
= (2.5*0.926*470[N/mm2]*16[mm]*10[mm])/1.25
= 139.259[kN] pt. 1-8 Table 3.4
z = zp + (n2 - 1)*p2/2
= 50[mm] + (1 - 1)*60[mm]/2
= 50[mm] SCI P358 p.115
IsSingleLineOfBoltsTrue
IsSingleLineOfBoltsTrue
IsSingleLineOfBoltsTrue
= (6*z)/(n1*(n1 + 1)*p1)
= (6*50[mm])/(3*(3 + 1)*60[mm])
= 0.417 SCI P358 p.115
Vpl,Rd = Av*(fy/(3)0.5)/M0/1.27
= 2000[mm2]*(355[N/mm2]/(3)0.5)/1/1.27
= 322.771[kN] [4]
VRd,n = Av,net*fu,p/(3)0.5/M2
= 1460[mm2]*470[N/mm2]/(3)0.5/1.25
= 316.942[kN] [4]
Block tearing [KN] 312.78 70.00 UDL 0.22 pt. 1-8 Eq. 3.10
IsSingleLineOfBoltsTrue
Ant = tp*(e2 - d0/2)
= 10[mm]*(50[mm] - 18[mm]/2)
= 410[mm2] SCI P358 p.118
Lateral torsional buckling [KN] 473.33 70.00 UDL 0.15 pt. 1-1 Eq. 6.55,
pt. 1-1 Eq. 6.13,
SCI P358 p.119
= 0.6 SCI P358 p.119
Wpl = tp*hp2/6
= 10[mm]*200[mm]2/6
= 66666.67[mm3] [4]
LT = 2.8/86.8*((zp*hp)/(1.5*tp2))0.5
= 2.8/86.8*((50[mm]*200[mm])/(1.5*10[mm]2))0.5
= 0.263 SCI P358 p.119
Mb,Rd = LT*Wpl*fy/M1
= 0.951*66666.67[mm3]*355[N/mm2]/1
= 22.506[kN*m] pt. 1-1 Eq. 6.55
Mc,Rd = Wpl*fy/M0
= 66666.67[mm3]*355[N/mm2]/1
= 23.667[kN*m] pt. 1-1 Eq. 6.13
z = zp + (n2 - 1)*p2/2
= 50[mm] + (1 - 1)*60[mm]/2
= 50[mm] SCI P358 p.115
zp>tp/0.1550[mm]>10[mm]/0.15False
VRd = Mc,Rd/z
= 23.667[kN*m]/50[mm]
= 473.333[kN] SCI P358 p.119
Beam
Bolt bearing [KN] 123.51 70.00 UDL 0.57 pt. 1-8 Table 3.4,
SCI P358 p.116
IsSingleLineOfBoltsTrue
d = p1/(3.0*d0) - 1.0/4.0
= 60[mm]/(3.0*18[mm]) - 1.0/4.0
= 0.861 pt. 1-8 Table 3.4
Fb,Rd = (k1*b*fu*d*t)/M2
= (2.5*0.796*470[N/mm2]*16[mm]*6.3[mm])/1.25
= 75.451[kN] pt. 1-8 Table 3.4
d = e2/(3.0*d0)
= 35[mm]/(3.0*18[mm])
= 0.648 [4]
Fb,Rd = (k1*b*fu*d*t)/M2
= (2.5*0.648*470[N/mm2]*16[mm]*6.3[mm])/1.25
= 61.413[kN] pt. 1-8 Table 3.4
z = zp + (n2 - 1)*p2/2
= 50[mm] + (1 - 1)*60[mm]/2
= 50[mm] SCI P358 p.115
IsSingleLineOfBoltsTrue
IsSingleLineOfBoltsTrue
IsSingleLineOfBoltsTrue
= (6*z)/(n1*(n1 + 1)*p1)
= (6*50[mm])/(3*(3 + 1)*60[mm])
= 0.417 SCI P358 p.115
Shear at gross section [KN] 308.22 70.00 UDL 0.23 pt. 1-1 Eq. 6.18
ATee = (hb - dnt - tf)*tw + b*tf
= (256[mm] - 25[mm] - 10.9[mm])*6.3[mm] + 146.4[mm]*10.9[mm]
= 2982.39[mm2] SCI P358 p.18,
p.121
Av,N = ATee - b*tf + (tw + 2.0*rb)*tf/2.0
= 2982.39[mm2] - 146.4[mm]*10.9[mm] + (6.3[mm] + 2.0*7.6[mm])*10.9[mm]/2.0
= 1503.81[mm2] SCI P358 p.18,
p.124
Vpl,Rd = Av*(fy/(3)0.5)/M0
= 1503.81[mm2]*(355[N/mm2]/(3)0.5)/1
= 308.219[kN] pt. 1-1 Eq. 6.18
Shear at net section [KN] 252.60 70.00 UDL 0.28 SCI P358 p.121
ATee = (hb - dnt - tf)*tw + b*tf
= (256[mm] - 25[mm] - 10.9[mm])*6.3[mm] + 146.4[mm]*10.9[mm]
= 2982.39[mm2] SCI P358 p.18,
p.121
Av,net = Av - n1*d0*tw
= 1503.81[mm2] - 3*18[mm]*6.3[mm]
= 1163.61[mm2] SCI P358 p.121
VRd,n = Av,net*fu/(3)0.5/M2
= 1163.61[mm2]*470[N/mm2]/(3)0.5/1.25
= 252.6[kN] SCI P358 p.121
Block tearing [KN] 183.16 70.00 UDL 0.38 pt. 1-8 Eq. 3.10
IsSingleLineOfBoltsTrue
Shear and bending interaction at the notch [KN*m] 32.04 6.84 UDL 0.21 SCI P358 p.18,
p.124,
pt. 1-1 Cl. 6.2.8
ATee = (hb - dnt - tf)*tw + b*tf
= (256[mm] - 25[mm] - 10.9[mm])*6.3[mm] + 146.4[mm]*10.9[mm]
= 2982.39[mm2] SCI P358 p.18,
p.121
Vpl,N,Rd = Av,N*fy/((3.0)0.5*M0)
= 1503.81[mm2]*355[N/mm2]/((3.0)0.5*1)
= 308.219[kN] SCI P358 p.18,
p.124
dnt>dnb25[mm]>0[mm]True
Wel,N,y = Iyy/zmax
= 1.55E+07[mm4]/171.85[mm]
= 90260.22[mm3] SCI P358 p.18,
p.122
VEd< = 0.5*Vpl,N,Rd70[kN]<
= 0.5*308.219[kN]True
Mv,N,Rd = fy*Wel,N,y/M0
= 355[N/mm2]*90260.22[mm3]/1
= 32.042[kN*m] pt. 1-1 Cl. 6.2.8
Lateral torsional buckling [KN*m] 107.90 0.00 UDL 0.00 pt. 1-1 Eq. 6.55
dn/hb = dn/hb
= 25[mm]/256[mm]
= 0.0977 [1]
ln/Lb = ln/Lb
= 82.7[mm]/3[m]
= 0.0276 [1]
= (235 [MPa]/fy)1/2
= (235 [MPa]/355[N/mm2])1/2
= 0.814 pt. 1-1 Table 5.2
C/t = C/t
= 62.45[mm]/10.9[mm]
= 5.729 pt. 1-1 Table 5.2
C/t = C/t
= 219[mm]/6.3[mm]
= 34.762 pt. 1-1 Table 5.2
1f = 9.0*
= 9.0*0.814
= 7.323 pt. 1-1 Table 5.2
2f = 10.0*
= 10.0*0.814
= 8.136 pt. 1-1 Table 5.2
3f = 14.0*
= 14.0*0.814
= 11.391 pt. 1-1 Table 5.2
1w = 72.0*
= 72.0*0.814
= 58.58 pt. 1-1 Table 5.2
2w = 83.0*
= 83.0*0.814
= 67.53 pt. 1-1 Table 5.2
3w = 124.0*
= 124.0*0.814
= 100.888 pt. 1-1 Table 5.2
z = (k*Lb)/iz
= (1*3[m])/34.781[mm]
= 86.253 [5]
g = (1 - Iz/Iy)0.5
= (1 - 5.71E+06[mm4]/5.54E+07[mm4])0.5
= 0.947 [5]
U = (Wpl*g/A*(Iz/Iw)0.5)0.5
= (4.83E+05[mm3]*0.947/4720[mm2]*(5.71E+06[mm4]/8.56E+10[mm6])0.5)0.5
= 0.89 [5]
V = 1/(1.0 + 1.0/20.0*(z/(h/tf))2)0.25
= 1/(1.0 + 1.0/20.0*(86.253/(256[mm]/10.9[mm]))2)0.25
= 0.879 [5]
x = 0.566*hs*(A/J)0.5
= 0.566*245.1[mm]*(4720[mm2]/1.47E+05[mm4])0.5
= 24.873 [6]
b = U*V*Lb/iz
= 0.89*0.879*3[m]/34.781[mm]
= 67.458 SCI P358 p.20,
p.126
b<3067.458<30False
K0 = Min(g0*x, Kmax)
= Min(5.88*24.873, 280)
= 146.255 SCI P358 p.20,
p.126
K = K0/b
= 146.255/67.458
= 2.168 SCI P358 p.20,
p.126
z = (k*Lb)/iz
= (1*3.672[m])/34.781[mm]
= 105.576 [5]
1 = π*(E/fy)0.5
= π*(2.05E+05[N/mm2]/355[N/mm2])0.5
= 75.494 pt. 1-1 Cl. 6.3.1.3
w = Wy/Wpl
= 4.83E+05[mm3]/4.83E+05[mm3]
=1 [5]
LT = 1.0/(C1)0.5*U*V*z/1*(w)0.5
= 1.0/(1)0.5*0.89*0.879*105.576/75.494*(1)0.5
= 1.094 [5]
Mb,Rd = LT*Wpl*fy/M1
= 0.629*4.83E+05[mm3]*355[N/mm2]/1
= 107.895[kN*m] pt. 1-1 Eq. 6.55
a = 0.7*s
= 0.7*8[mm]
= 5.6[mm] Sec. 4.5.2
= VEd/(2.0*a*Lw)
= 70[kN]/(2.0*5.6[mm]*200[mm])
= 31.25[N/mm2] pt. 1-8 Eq. 4.1
w = (
[N/mm2][N/mm2][N/mm2]
[N/mm2]
Support
Web or wall punching shear [KN] 441.17 70.00 UDL 0.16 SCI P358 p.128
Wpl = tp*hp2/6
= 10[mm]*200[mm]2/6
= 66666.67[mm3] [4]
z = zp + (n2 - 1)*p2/2
= 50[mm] + (1 - 1)*60[mm]/2
= 50[mm] SCI P358 p.115
VRd = (Wpl*fu*t2/tp)/(z*M2)
= (66666.67[mm3]*470[N/mm2]*8.8[mm]/10[mm])/(50[mm]*1.25)
= 441.173[kN] SCI P358 p.128
Web local shear with beams in both sides [KN] 360.73 37.33 UDL 0.10 pt. 1-1 Eq. 6.18
hpmin = Min(hp1, hp2)
= Min(200[mm], 3000[mm])
= 200[mm] SCI P358 p.129
Av = hpmin*t2
= 200[mm]*8.8[mm]
= 1760[mm2] SCI P358 p.129
Vpl,Rd = Av*(fy/(3)0.5)/M0
= 1760[mm2]*(355[N/mm2]/(3)0.5)/1
= 360.728[kN] pt. 1-1 Eq. 6.18
VEd,tot/2 = VEd,tot/2
= 74.667[kN]/2
= 37.333[kN] SCI P358 p.129
M2 = Mu
= 1.1 SCI P358 p.4
Nu,Rd = 0.9*Anet*fu/M2
= 0.9*1460[mm2]*470[N/mm2]/1.1
= 561.436[kN] pt. 1-1 Eq. 6.7
Block tearing due to tension [KN] 526.98 0.00 UDL 0.00 pt. 1-8 Eq. 3.9
Ant = tp*((n1 - 1)*p1 - (n1 - 1)*d0)
= 10[mm]*((3 - 1)*60[mm] - (3 - 1)*18[mm])
= 840[mm2] SCI P358 p.130
IsSingleLineOfBoltsTrue
M2 = Mu
= 1.1 SCI P358 p.4
VEff,1,Rd = fu*Ant/M2 + (1/(3)0.5)*fy*Anv/M0
= 470[N/mm2]*840[mm2]/1.1 + (1/(3)0.5)*355[N/mm2]*820[mm2]/1
= 526.976[kN] pt. 1-8 Eq. 3.9
IsSingleLineOfBoltsTrue
M2 = Mu
= 1.1 SCI P358 p.4
Bolt shear [KN] 205.09 0.00 UDL 0.00 pt. 1-8 Table 3.4
M2 = Mu
= 1.1 SCI P358 p.4
Fv,Rd = (v*fub*A)/M2
= (0.6*800[N/mm2]*156.668[mm2])/1.1
= 68.364[kN] pt. 1-8 Table 3.4
FRd = n*Fv,Rd
= 3*68.364[kN]
= 205.093[kN] pt. 1-8 Table 3.4
Bolt bearing due to tension [KN] 474.75 0.00 UDL 0.00 pt. 1-8 Table 3.4
M2 = Mu
= 1.1 SCI P358 p.4
d = e2/(3.0*d0)
= 50[mm]/(3.0*18[mm])
= 0.926 [4]
Fb,Rd = (k1*b*fu*d*t)/M2
= (2.5*0.926*470[N/mm2]*16[mm]*10[mm])/1.1
= 158.249[kN] pt. 1-8 Table 3.4
FRd = n*Fb,Rd
= 3*158.249[kN]
= 474.747[kN] pt. 1-8 Table 3.4
Nu,Rd = 0.9*Anet*fu/M2
= 0.9*919.8[mm2]*470[N/mm2]/1.1
= 353.705[kN] pt. 1-1 Eq. 6.7
Block tearing due to tension [KN] 293.26 0.00 UDL 0.00 pt. 1-8 Eq. 3.9
Ant = tw*((n1 - 1)*p1 - (n1 - 1)*d0)
= 6.3[mm]*((3 - 1)*60[mm] - (3 - 1)*18[mm])
= 529.2[mm2] SCI P358 p.131
IsSingleLineOfBoltsTrue
M2 = Mu
= 1.1 SCI P358 p.4
IsSingleLineOfBoltsTrue
M2 = Mu
= 1.1 SCI P358 p.4
Bolt bearing due to tension [KN] 209.36 0.00 UDL 0.00 pt. 1-8 Table 3.4
M2 = Mu
= 1.1 SCI P358 p.4
d = e2/(3.0*d0)
= 35[mm]/(3.0*18[mm])
= 0.648 [4]
Fb,Rd = (k1*b*fu*d*t)/M2
= (2.5*0.648*470[N/mm2]*16[mm]*6.3[mm])/1.1
= 69.788[kN] pt. 1-8 Table 3.4
FRd = n*Fb,Rd
= 3*69.788[kN]
= 209.364[kN] pt. 1-8 Table 3.4
------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Global critical strength ratio 0.62
------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
NOTATION
a: Effective throat size of the weld, distance between the first line of bolts and the face of the support
A: Gross section area
Anet: Net area subjected to tension
Ant: Net area subjected to tension
Anv: Net area subjected to shear
ATee: Shear area of the Tee section
Av: Shear area
Av,N: Shear area at single notched beam
Av,net: Net shear area
: Fin plate bolt group factor
b: Bolt bearing resistance factor, Table 3.4
d: Bolt bearing resistance factor, Table 3.4
LT: Imperfection factor
v: Bolt shear resistance factor, Table 3.4
b: Width
1f: Flange width-to-thickness ratio limit for class 1
1w: Web width-to-thickness ratio limit for class 1
2f: Flange width-to-thickness ratio limit for class 2
2w: Web width-to-thickness ratio limit for class 2
3f: Flange width-to-thickness ratio limit for class 3
3w: Web width-to-thickness ratio limit for class 3
: Fin plate bolt group factor
: Correction factor for the lateral torsional buckling curves for rolled and welded sections
w: Correlation factor taken from Table 4.1
w: Section modulus ratio for lateral torsional buckling
C: Width of the member section subject to compression
C1 : Parameter dependent on the shape of the bending moment diagram
C/t: Flange slenderness ratio
C/t: Web slenderness ratio
ln/Lb: Notch length - Beam length ratio
(ln/Lb)max: Notch length - Beam length ratio limit
d: Nominal bolt diameter
d0: Hole diameter
demin: Minimum edge distance
dnmin: Minimum notch depth
dn: Notch height
dnb: Bottom notch height
dnmax: Maximum notch height
dnt: Top notch height
dn/hb: Notch height - beam depth ratio
(dn/hb)max: Notch height - beam depth ratio limit
E: Steel modulus of elasticity
e1: End distance
e2: Edge distance
: Constant (235/fy)^0.5
f: Modification factor for the reduction factor for lateral-torsional buckling
Fb,Rd: Design bearing resistance per bolt
Fb,Rd,hor: Design bearing resistance per bolt in a horizontal direction
Fb,Rd,ver: Design bearing resistance per bolt in a vertical direction
FRd: Design resistance of the bolt group
fu: Ultimate tensile strength of the steel on which the bolt bears
fu: Ultimate tensile strength
fub: Ultimate tensile strength of the bolt
fu,p: Ultimate tensile strength of the bolt
fu: Nominal ultimate tensile strength of the weaker part joined
Fv,Rd: Design shear resistance per bolt
fvwd: Design shear strength of fillet welds
fy: Yield strength
fy,p: Yield strength of the plate material
g: Factor for lateral torsional buckling
g0: Lateral torsional buckling factor
gh: Horizontal gap between members
M0: Partial factor for resistance of cross-sections whatever the class is
M1: Partial factor for resistance of members to instability assessed by member checks
M2: Partial factor for resistance of cross-sections in tension to fracture
Mu: Partial factor for resistance of components when verifying structural integrity
h: Section height
hb: Height of the member
hp: Height of plate
hp1: Height of right plate
hp2: Height of left plate
hpmin: Minimum plate height
hs: Distance between flanges shear centers
HasDoubleNotch: Has double notch
Ibg: Moment of inertia of bolt group
Iw: Warping constant
Iy: Moment of inertia about major axis
Iyy: Second moment of area about y-y axis
iz: Radius of gyration about the minor axis
Iz: Moment of inertia about minor axis
IsSingleLineOfBolts: Single line of bolts
J: Torsional constant
k: Effective length factor
K: Lateral torsional buckling factor
K0: Lateral torsional buckling factor
k 1: Bolt bearing factor
kc: Correction factor
Kmax: Lateral torsional buckling factor
ktop: Thickness of the top flange + root radius
kbottom: Thickness of the bottom flange + root radius
: Factor to account for the triangular shape of the bending moment diagram in the fin plate
Lb: Beam length
LE: Modified effective length for lateral torsional buckling
Lmax: Maximum length
Lmin: Minimum length
ln: Notch length
lnmax: Maximum notch length
Lw: Length of weld
1: Limiting slenderness for axial compression
b: Equivalent slenderness for un-notched beam
LT: Non dimensional slenderness for lateral-torsional buckling
LT,0: Plateau length of the lateral torsional buckling curves for rolled and welded sections
z: Non dimensional slenderness about minor axis
LT: Reduction factor for lateral-torsional buckling
LT,mod: Modified reduction factor for lateral-torsional buckling
Mb,Rd: Design buckling resistance moment
Mc,Rd: Design resistance for bending about one principal axis of a cross-section
MEd: Design moment
Mv,N,Rd: Moment resistance of a single notched beam at the notch
n: Total number of bolts
n1: Number of horizontal bolt rows
n2: Number of vertical bolt rows
Nu,Rd: Design ultimate resistance of the net section at holes
p1: Vertical spacing between centres of bolts in a line in the load direction
p2: Horizontal spacing between centres of bolts in adjacent lines perpendicular to the load direction
pmax: Maximum bolts spacing
LT: Value to determine lateral-torsional buckling reduction factor
rb : Root radius of the beam section
rs : Root radius of the support section
s: Weld size
REFERENCES
[1] Joints in Steel Construction – Simple Joints to Eurocode 3 (P358), SCI and BCSA, 2011.
[4] SN017 NCCI: Shear resistance of a fin plate connection.
[5] SN002 NCCI: Determination of non-dimensional slenderness of I and H sections.
[6] Steel Building Design: Design Data In accordance with Eurocodes and the UK National Annexes (P363) SCI and BCSA, 2011
AECOM
Current Date: 1/6/2022 6:48 PM
Units system: SI
File name: C:\Users\sujeevanleonard.tham\OneDrive - AECOM\Projects\J110\J110\OneDrive_2021-07-01\12. Southern Staircase\Design
Files\Str\Connection Design\B40A TO 50A.rcnx
Steel connections
Results
____________________________________________________________________________________________________________________________
___________________________________________________________________________________
DEMANDS
Description Pu Ru RuLeft Mu Mmax C1
[kN] [kN] [kN] [kN*m] [kN*m]
-----------------------------------------------------------------------------------------------------------
UDL 0.00 70.00 0.00 0.00 0.00 0.00
-----------------------------------------------------------------------------------------------------------
GEOMETRIC CONSIDERATIONS
Dimensions Unit Value Min. value Max. value Sta. References
----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Fin plate
Length [mm] 340.00 238.80 360.40 [1]
Lmin = 0.6*hb
= 0.6*398[mm]
= 238.8[mm] [1]
Lmin = 0.6*hb
= 0.6*398[mm]
= 238.8[mm] [1]
Vertical center-to-center spacing (pitch) [mm] 80.00 39.60 168.00 pt. 1-8 Table 3.3
p1 = 2.2*d0
= 2.2*18[mm]
= 39.6[mm] pt. 1-8 Table 3.3
Beam
Thickness [mm] 6.40 -- 6.72 [1]
tp = 0.42*d
= 0.42*16[mm]
= 6.72[mm] [1]
----------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
DESIGN CHECK
Verification Unit Capacity Demand Ctrl EQ Ratio References
------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Plate (beam side)
Bolt group shear [KN] 92.75 70.00 UDL 0.75 pt. 1-8 Table 3.4,
SCI P358 p.115
Fv,Rd = (v*fub*A)/M2
= (0.6*800[N/mm2]*156.668[mm2])/1.25
= 60.161[kN] pt. 1-8 Table 3.4
z = zp + (n2 - 1)*p2/2
= 159.6[mm] + (1 - 1)*60[mm]/2
= 159.6[mm] SCI P358 p.115
IsSingleLineOfBoltsTrue
IsSingleLineOfBoltsTrue
IsSingleLineOfBoltsTrue
= (6*z)/(n1*(n1 + 1)*p1)
= (6*159.6[mm])/(4*(4 + 1)*80[mm])
= 0.599 SCI P358 p.115
Bolt group bearing [KN] 257.64 70.00 UDL 0.27 pt. 1-8 Table 3.4,
SCI P358 p.116
IsSingleLineOfBoltsTrue
d = e1/(3.0*d0)
= 50[mm]/(3.0*18[mm])
= 0.926 pt. 1-8 Table 3.4
d = p1/(3.0*d0) - 1.0/4.0
= 80[mm]/(3.0*18[mm]) - 1.0/4.0
= 1.231 pt. 1-8 Table 3.4
Fb,Rd = (k1*b*fu*d*t)/M2
= (2.5*0.926*470[N/mm2]*16[mm]*12[mm])/1.25
= 167.111[kN] pt. 1-8 Table 3.4
d = e2/(3.0*d0)
= 50[mm]/(3.0*18[mm])
= 0.926 [4]
Fb,Rd = (k1*b*fu*d*t)/M2
= (2.5*0.926*470[N/mm2]*16[mm]*12[mm])/1.25
= 167.111[kN] pt. 1-8 Table 3.4
z = zp + (n2 - 1)*p2/2
= 159.6[mm] + (1 - 1)*60[mm]/2
= 159.6[mm] SCI P358 p.115
IsSingleLineOfBoltsTrue
IsSingleLineOfBoltsTrue
= (6*z)/(n1*(n1 + 1)*p1)
= (6*159.6[mm])/(4*(4 + 1)*80[mm])
= 0.599 SCI P358 p.115
Vpl,Rd = Av*(fy/(3)0.5)/M0/1.27
= 4080[mm2]*(355[N/mm2]/(3)0.5)/1/1.27
= 658.452[kN] [4]
VRd,n = Av,net*fu,p/(3)0.5/M2
= 3216[mm2]*470[N/mm2]/(3)0.5/1.25
= 698.141[kN] [4]
Block tearing [KN] 650.81 70.00 UDL 0.11 pt. 1-8 Eq. 3.10
IsSingleLineOfBoltsTrue
Shear due to bending [KN] 514.26 70.00 UDL 0.14 pt. 1-1 Eq. 6.13,
SCI P358 p.119
z = zp + (n2 - 1)*p2/2
= 159.6[mm] + (1 - 1)*60[mm]/2
= 159.6[mm] SCI P358 p.115
z = zp + (n2 - 1)*p2/2
= 159.6[mm] + (1 - 1)*60[mm]/2
= 159.6[mm] SCI P358 p.115
hp < 2.73*z 1
Wpl = tp*hp2/6
= 12[mm]*340[mm]2/6
= 2.31E+05[mm3] [4]
Mc,Rd = Wpl*fy/M0
= 2.31E+05[mm3]*355[N/mm2]/1
= 82.076[kN*m] pt. 1-1 Eq. 6.13
VRd = Mc,Rd/z
= 82.076[kN*m]/159.6[mm]
= 514.261[kN] SCI P358 p.119
Lateral torsional buckling [KN] 514.26 70.00 UDL 0.14 pt. 1-1 Eq. 6.55,
pt. 1-1 Eq. 6.13,
SCI P358 p.119
= 0.6 SCI P358 p.119
Wpl = tp*hp2/6
= 12[mm]*340[mm]2/6
= 2.31E+05[mm3] [4]
LT = 2.8/86.8*((zp*hp)/(1.5*tp2))0.5
= 2.8/86.8*((159.6[mm]*340[mm])/(1.5*12[mm]2))0.5
= 0.511 SCI P358 p.119
Mb,Rd = LT*Wpl*fy/M1
= 0.771*2.31E+05[mm3]*355[N/mm2]/1
= 63.314[kN*m] pt. 1-1 Eq. 6.55
Mc,Rd = Wpl*fy/M0
= 2.31E+05[mm3]*355[N/mm2]/1
= 82.076[kN*m] pt. 1-1 Eq. 6.13
z = zp + (n2 - 1)*p2/2
= 159.6[mm] + (1 - 1)*60[mm]/2
= 159.6[mm] SCI P358 p.115
zp>tp/0.15159.6[mm]>12[mm]/0.15True
Beam
Bolt bearing [KN] 126.57 70.00 UDL 0.55 pt. 1-8 Table 3.4,
SCI P358 p.116
IsSingleLineOfBoltsTrue
d = e1/(3.0*d0)
= 79[mm]/(3.0*18[mm])
= 1.463 pt. 1-8 Table 3.4
d = p1/(3.0*d0) - 1.0/4.0
= 80[mm]/(3.0*18[mm]) - 1.0/4.0
= 1.231 pt. 1-8 Table 3.4
b = min(d, fub/fu, 1.0)
= min(1.231, 800[N/mm2]/470[N/mm2], 1.0)
=1 pt. 1-8 Table 3.4
Fb,Rd = (k1*b*fu*d*t)/M2
= (2.5*1*470[N/mm2]*16[mm]*6.4[mm])/1.25
= 96.256[kN] pt. 1-8 Table 3.4
d = e2/(3.0*d0)
= 45[mm]/(3.0*18[mm])
= 0.833 [4]
Fb,Rd = (k1*b*fu*d*t)/M2
= (2.5*0.833*470[N/mm2]*16[mm]*6.4[mm])/1.25
= 80.213[kN] pt. 1-8 Table 3.4
z = zp + (n2 - 1)*p2/2
= 159.6[mm] + (1 - 1)*60[mm]/2
= 159.6[mm] SCI P358 p.115
IsSingleLineOfBoltsTrue
IsSingleLineOfBoltsTrue
IsSingleLineOfBoltsTrue
= (6*z)/(n1*(n1 + 1)*p1)
= (6*159.6[mm])/(4*(4 + 1)*80[mm])
= 0.599 SCI P358 p.115
Shear at gross section [KN] 566.00 70.00 UDL 0.12 pt. 1-1 Eq. 6.18
Av = Max(Ag - bf,top*tf,top - bf,bottom*tf,bottom + ((tw + 2*rb,top)*tf,top/2) + ((tw + 2*rb,bottom)*tf,bottom/2), hw*tw)
= Max(4970[mm2] - 141.8[mm]*8.6[mm] - 141.8[mm]*8.6[mm] + ((6.4[mm] + 2*10.2[mm])*8.6[mm]/2) +
((6.4[mm] + 2*10.2[mm])*8.6[mm]/2), 380.8[mm]*6.4[mm])
= 2761.52[mm2] SCI P358 p.121
Vpl,Rd = Av*(fy/(3)0.5)/M0
= 2761.52[mm2]*(355[N/mm2]/(3)0.5)/1
= 565.999[kN] pt. 1-1 Eq. 6.18
Shear at net section [KN] 499.45 70.00 UDL 0.14 SCI P358 p.121
Av = Max(Ag - bf,top*tf,top - bf,bottom*tf,bottom + ((tw + 2*rb,top)*tf,top/2) + ((tw + 2*rb,bottom)*tf,bottom/2), hw*tw)
= Max(4970[mm2] - 141.8[mm]*8.6[mm] - 141.8[mm]*8.6[mm] + ((6.4[mm] + 2*10.2[mm])*8.6[mm]/2) +
((6.4[mm] + 2*10.2[mm])*8.6[mm]/2), 380.8[mm]*6.4[mm])
= 2761.52[mm2] SCI P358 p.121
Av,net = Av - n1*d0*tw
= 2761.52[mm2] - 4*18[mm]*6.4[mm]
= 2300.72[mm2] SCI P358 p.121
VRd,n = Av,net*fu/(3)0.5/M2
= 2300.72[mm2]*470[N/mm2]/(3)0.5/1.25
= 499.449[kN] SCI P358 p.121
Shear and bending interaction of the web [KN*m] 35.98 11.17 UDL 0.31 SCI P358 p.123
Vpl,BC,Rd = (tw*(n1 - 1)*p1*fy)/((3)0.5*M0)
= (6.4[mm]*(4 - 1)*80[mm]*355[N/mm2])/((3)0.5*1)
= 314.818[kN] pt. 1-1 Eq. 6.18,
SCI P358 p.123
VBC,Ed = VEd*(n1)*p1/hb
= 70[kN]*(4)*80[mm]/398[mm]
= 56.281[kN] SCI P358 p.123
zp > tp/0.15 1
VBC,Ed = VEd*(n1)*p1/hb
= 70[kN]*(4)*80[mm]/398[mm]
= 56.281[kN] SCI P358 p.123
VBC,Ed>0.5*Vpl,BC,Rd56.281[kN]>0.5*314.818[kN]False
IsSingleLineOfBoltsTrue
Vpl,AB,Rd = (tw*e2*fy)/((3)0.5*M0)
= (6.4[mm]*45[mm]*355[N/mm2])/((3)0.5*1)
= 59.028[kN] pt. 1-1 Eq. 6.18,
SCI P358 p.123
a = 0.7*s
= 0.7*8[mm]
= 5.6[mm] Sec. 4.5.2
= VEd/(2.0*a*Lw)
= 70[kN]/(2.0*5.6[mm]*360.4[mm])
= 17.342[N/mm2] pt. 1-8 Eq. 4.1
w = (
[N/mm2][N/mm2][N/mm2]
[N/mm2]
Support
Web or wall local shear with one beam [KN] 668.99 70.00 UDL 0.10 pt. 1-1 Eq. 6.18
Av = hp*t2
= 340[mm]*9.6[mm]
= 3264[mm2] SCI P358 p.128
Vpl,Rd = Av*(fy/(3)0.5)/M0
= 3264[mm2]*(355[N/mm2]/(3)0.5)/1
= 668.987[kN] pt. 1-1 Eq. 6.18
Web or wall punching shear [KN] 435.75 70.00 UDL 0.16 SCI P358 p.128
Wpl = tp*hp2/6
= 12[mm]*340[mm]2/6
= 2.31E+05[mm3] [4]
z = zp + (n2 - 1)*p2/2
= 159.6[mm] + (1 - 1)*60[mm]/2
= 159.6[mm] SCI P358 p.115
VRd = (Wpl*fu*t2/tp)/(z*M2)
= (2.31E+05[mm3]*470[N/mm2]*9.6[mm]/12[mm])/(159.6[mm]*1.25)
= 435.745[kN] SCI P358 p.128
M2 = Mu
= 1.1 SCI P358 p.4
Nu,Rd = 0.9*Anet*fu/M2
= 0.9*3216[mm2]*470[N/mm2]/1.1
= 1236.7[kN] pt. 1-1 Eq. 6.7
Block tearing due to tension [KN] 1155.35 0.00 UDL 0.00 pt. 1-8 Eq. 3.9
Ant = tp*((n1 - 1)*p1 - (n1 - 1)*d0)
= 12[mm]*((4 - 1)*80[mm] - (4 - 1)*18[mm])
= 2232[mm2] SCI P358 p.130
IsSingleLineOfBoltsTrue
M2 = Mu
= 1.1 SCI P358 p.4
IsSingleLineOfBoltsTrue
M2 = Mu
= 1.1 SCI P358 p.4
Bolt shear [KN] 273.46 0.00 UDL 0.00 pt. 1-8 Table 3.4
M2 = Mu
= 1.1 SCI P358 p.4
Fv,Rd = (v*fub*A)/M2
= (0.6*800[N/mm2]*156.668[mm2])/1.1
= 68.364[kN] pt. 1-8 Table 3.4
FRd = n*Fv,Rd
= 4*68.364[kN]
= 273.457[kN] pt. 1-8 Table 3.4
Bolt bearing due to tension [KN] 759.60 0.00 UDL 0.00 pt. 1-8 Table 3.4
M2 = Mu
= 1.1 SCI P358 p.4
d = e2/(3.0*d0)
= 50[mm]/(3.0*18[mm])
= 0.926 [4]
Fb,Rd = (k1*b*fu*d*t)/M2
= (2.5*0.926*470[N/mm2]*16[mm]*12[mm])/1.1
= 189.899[kN] pt. 1-8 Table 3.4
FRd = n*Fb,Rd
= 4*189.899[kN]
= 759.596[kN] pt. 1-8 Table 3.4
M2 = Mu
= 1.1 SCI P358 p.4
Nu,Rd = 0.9*Anet*fu/M2
= 0.9*1715.2[mm2]*470[N/mm2]/1.1
= 659.572[kN] pt. 1-1 Eq. 6.7
Block tearing due to tension [KN] 603.07 0.00 UDL 0.00 pt. 1-8 Eq. 3.9
Ant = tw*((n1 - 1)*p1 - (n1 - 1)*d0)
= 6.4[mm]*((4 - 1)*80[mm] - (4 - 1)*18[mm])
= 1190.4[mm2] SCI P358 p.131
IsSingleLineOfBoltsTrue
M2 = Mu
= 1.1 SCI P358 p.4
IsSingleLineOfBoltsTrue
M2 = Mu
= 1.1 SCI P358 p.4
Bolt bearing due to tension [KN] 364.61 0.00 UDL 0.00 pt. 1-8 Table 3.4
M2 = Mu
= 1.1 SCI P358 p.4
d = e2/(3.0*d0)
= 45[mm]/(3.0*18[mm])
= 0.833 [4]
Fb,Rd = (k1*b*fu*d*t)/M2
= (2.5*0.833*470[N/mm2]*16[mm]*6.4[mm])/1.1
= 91.152[kN] pt. 1-8 Table 3.4
FRd = n*Fb,Rd
= 4*91.152[kN]
= 364.606[kN] pt. 1-8 Table 3.4
------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
Global critical strength ratio 0.75
------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------
NOTATION
a: Effective throat size of the weld, distance between the first line of bolts and the face of the support
A: Gross section area
Ag: Gross cross-sectional area
Anet: Net area subjected to tension
Ant: Net area subjected to tension
Anv: Net area subjected to shear
Av: Shear area
Av,net: Net shear area
: Fin plate bolt group factor
b: Bolt bearing resistance factor, Table 3.4
d: Bolt bearing resistance factor, Table 3.4
LT: Imperfection factor
v: Bolt shear resistance factor, Table 3.4
bf,top: Beam top flange width
bf,bottom: Beam bottom flange width
: Fin plate bolt group factor
w: Correlation factor taken from Table 4.1
d: Nominal bolt diameter
d0: Hole diameter
demin: Minimum edge distance
dnb: Bottom notch height
dnt: Top notch height
e1: End distance
e2: Edge distance
Fb,Rd: Design bearing resistance per bolt
Fb,Rd,hor: Design bearing resistance per bolt in a horizontal direction
Fb,Rd,ver: Design bearing resistance per bolt in a vertical direction
FRd: Design resistance of the bolt group
fu: Ultimate tensile strength of the steel on which the bolt bears
fu: Ultimate tensile strength
fub: Ultimate tensile strength of the bolt
fu,p: Ultimate tensile strength of the bolt
fu: Nominal ultimate tensile strength of the weaker part joined
Fv,Rd: Design shear resistance per bolt
fvwd: Design shear strength of fillet welds
fy: Yield strength
fy,p: Yield strength of the plate material
M0: Partial factor for resistance of cross-sections whatever the class is
M1: Partial factor for resistance of members to instability assessed by member checks
M2: Partial factor for resistance of cross-sections in tension to fracture
Mu: Partial factor for resistance of components when verifying structural integrity
hb: Height of the member
hp: Height of plate
hw: Clear depth between flanges
Ibg: Moment of inertia of bolt group
IsSingleLineOfBolts: Single line of bolts
k 1: Bolt bearing factor
ktop: Thickness of the top flange + root radius
kbottom: Thickness of the bottom flange + root radius
: Factor to account for the triangular shape of the bending moment diagram in the fin plate
Lmax: Maximum length
Lmin: Minimum length
Lw: Length of weld
LT: Non dimensional slenderness for lateral-torsional buckling
LT: Reduction factor for lateral-torsional buckling
MBC: Web beam resistance moment
Mb,Rd: Design buckling resistance moment
Mc,BC,Rd: Moment capacity of the beam web at section BC
Mc,Rd: Design resistance for bending about one principal axis of a cross-section
MEd: Design moment
n: Total number of bolts
n1: Number of horizontal bolt rows
n2: Number of vertical bolt rows
Nu,Rd: Design ultimate resistance of the net section at holes
p1: Vertical spacing between centres of bolts in a line in the load direction
p2: Horizontal spacing between centres of bolts in adjacent lines perpendicular to the load direction
pmax: Maximum bolts spacing
LT: Value to determine lateral-torsional buckling reduction factor
rb,top: Root radius of the top flange beam section
rb,bottom: Root radius of the bottom flange beam section
s: Weld size
REFERENCES
[1] Joints in Steel Construction – Simple Joints to Eurocode 3 (P358), SCI and BCSA, 2011.
[4] SN017 NCCI: Shear resistance of a fin plate connection.
Hilti PROFIS Engineering 3.0.74
www.hilti.com.sg
Company: Page: 1
Address: Specifier:
Phone I Fax: | E-Mail:
Design: B25A TO EXISTING RC BEAM Date: 06/01/2022
Fastening point:
Specifier's comments:
1 Input data
Anchor type and diameter: HIT-RE 500 V3 100 years + HAS-U 8.8 HDG M16
Return period (service life in years): 100
Item number: 2223911 HAS-U 8.8 HDG M16x300 (element) /
2123403 HIT-RE 500 V3 (adhesive)
Filling set or any suitable annular gap filling solution
Effective embedment depth: hef,act = 150.0 mm (hef,limit = - mm)
Material: 8.8
Evaluation Service Report: ETA 16/0143
Issued I Valid: 14/05/2019 | -
Proof: Design Method EN 1992-4, Chemical
Stand-off installation: eb = 0.0 mm (no stand-off); t = 16.0 mm
Anchor plate :
R lx x ly x t = 300.0 mm x 200.0 mm x 16.0 mm; (Recommended plate thickness: not calculated)
Application also possible with HVU2 + HAS-U 8.8 HDG M16_hef1 under the selected boundary conditions.
More information in section Alternative fastening data of this report.
R
- The anchor calculation is based on a rigid anchor plate assumption.
Input data and results must be checked for conformity with the existing conditions and for plausibility!
PROFIS Engineering ( c ) 2003-2022 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
1
Hilti PROFIS Engineering 3.0.74
www.hilti.com.sg
Company: Page: 2
Address: Specifier:
Phone I Fax: | E-Mail:
Design: B25A TO EXISTING RC BEAM Date: 06/01/2022
Fastening point:
y
Anchor reactions [kN]
Tension force: (+Tension, -Compression) 6 4 2
Anchor Tension force Shear force Shear force x Shear force y
1 0.000 5.000 5.000 0.000
2 0.000 5.000 5.000 0.000 x
3 0.000 5.000 5.000 0.000
4 0.000 5.000 5.000 0.000
5 3 1
5 0.000 5.000 5.000 0.000
6 0.000 5.000 5.000 0.000
Anchor forces are calculated based on the assumption of a rigid anchor plate.
Input data and results must be checked for conformity with the existing conditions and for plausibility!
PROFIS Engineering ( c ) 2003-2022 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
2
Hilti PROFIS Engineering 3.0.74
www.hilti.com.sg
Company: Page: 3
Address: Specifier:
Phone I Fax: | E-Mail:
Design: B25A TO EXISTING RC BEAM Date: 06/01/2022
Fastening point:
Input data and results must be checked for conformity with the existing conditions and for plausibility!
PROFIS Engineering ( c ) 2003-2022 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
3
Hilti PROFIS Engineering 3.0.74
www.hilti.com.sg
Company: Page: 4
Address: Specifier:
Phone I Fax: | E-Mail:
Design: B25A TO EXISTING RC BEAM Date: 06/01/2022
Fastening point:
V
VEd £ VRd,s = Rk,s EN 1992-4, Table 7.2
gM,s
0
VRk,s = k7 · VRk,s EN 1992-4, Eq. (7.35)
0
VRk,s [kN] k7 VRk,s [kN] gM,s VRd,s [kN] VEd [kN]
62.800 1.000 62.800 1.250 50.240 5.000
Input data and results must be checked for conformity with the existing conditions and for plausibility!
PROFIS Engineering ( c ) 2003-2022 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
4
Hilti PROFIS Engineering 3.0.74
www.hilti.com.sg
Company: Page: 5
Address: Specifier:
Phone I Fax: | E-Mail:
Design: B25A TO EXISTING RC BEAM Date: 06/01/2022
Fastening point:
V
VEd £ VRd,cp = Rk,cp EN 1992-4, Table 7.2
gM,c,p
VRk,cp = k8 · min {NRk,c; NRk,p} EN 1992-4, Eq. (7.39c)
0 A
NRk,p = NRk,p · 0p,N · y g,Np · y s,Np · y re,N · y ec1,Np · y ec2,Np EN 1992-4, Eq. (7.13)
Ap,N
0
NRk,p = y sus · t Rk · p · d · hef EN 1992-4, Eq. (7.14)
y sus =1 EN 1992-4, Eq. (7.14a)
scr,Np = 7.3 · d · √y sus · t Rk £ 3 · hef EN 1992-4, Eq. (7.15)
0,5
y g,Np
0
= y g,Np - (s s )
cr,Np
· (y g,Np - 1) ³ 1.00
0
EN 1992-4, Eq. (7.17)
1,5
0
y g,Np = √n - (√n - 1) · (tt ) Rk
Rk,c
³ 1.00 EN 1992-4, Eq. (7.18)
k3
t Rk,c = · √hef · fck EN 1992-4, Eq. (7.19)
p·d
c
y s,Np = 0.7 + 0.3 · 1.00 EN 1992-4, Eq. (7.20)
ccr,Np £
1
y ec1,Np = 1.00 EN 1992-4, Eq. (7.21)
2 · ec1,N £
1+ (
scr,Np )
1
y ec2,Np = 1.00 EN 1992-4, Eq. (7.21)
2 · ec2,N £
1+ (
scr,Np )
2 0 2 2 2
Ap,N [mm ] Ap,N [mm ] t Rk,ucr,20 [N/mm ] ccr,Np [mm] scr,Np [mm] cmin [mm] fc,cyl [N/mm ]
232,991 177,349 13.00 210.6 421.1 60.0 32.00
0
yc t Rk,cr [N/mm ]
2
k3 t Rk,c [N/mm ]
2
k8 y g,Np
Group anchor ID
1-6
Input data and results must be checked for conformity with the existing conditions and for plausibility!
PROFIS Engineering ( c ) 2003-2022 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
5
Hilti PROFIS Engineering 3.0.74
www.hilti.com.sg
Company: Page: 6
Address: Specifier:
Phone I Fax: | E-Mail:
Design: B25A TO EXISTING RC BEAM Date: 06/01/2022
Fastening point:
V
VEd £ VRd,c = Rk,c EN 1992-4, Table 7.2
gM,c
0 Ac,V
VRk,c = kT · VRk,c · 0
· y s,V · y h,V · y a,V · y ec,V · y re,V EN 1992-4, Eq. (7.40)
Ac,V
0 a b 1,5
VRk,c = k9 · dnom · lf · √fck · c1 EN 1992-4, Eq. (7.41)
0,5
a = 0.1 · () lf
c1
EN 1992-4, Eq. (7.42)
0,2
= 0.1 · (
c )
d nom
b EN 1992-4, Eq. (7.43)
1
0 2
Ac,V = 4.5 · c1 EN 1992-4, Eq. (7.44)
c2
y s,V = 0.7 + 0.3 · 1.00 EN 1992-4, Eq. (7.45)
1.5 · c1 £
0,5
y h,V = (1.5h· c ) 1
³ 1.00 EN 1992-4, Eq. (7.46)
1
y ec,V = £ 1.00 EN 1992-4, Eq. (7.47)
1+ ( 2 · eV
3 · c1 )
y a,V = √(cos a ) + (10.5 · sin a )
V
2
V
2 ³ 1.00 EN 1992-4, Eq. (7.48)
Comments: Tension displacements are valid with half of the required installation torque moment for uncracked concrete! Shear displacements
are valid without friction between the concrete and the anchor plate! The gap due to the drilled hole and clearance hole tolerances are not
included in this calculation!
The acceptable anchor displacements depend on the fastened construction and must be defined by the designer!
Input data and results must be checked for conformity with the existing conditions and for plausibility!
PROFIS Engineering ( c ) 2003-2022 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
6
Hilti PROFIS Engineering 3.0.74
www.hilti.com.sg
Company: Page: 7
Address: Specifier:
Phone I Fax: | E-Mail:
Design: B25A TO EXISTING RC BEAM Date: 06/01/2022
Fastening point:
6 Warnings
• The anchor design methods in PROFIS Engineering require rigid anchor plates per current regulations (AS 5216:2021, ETAG 001/Annex C,
EOTA TR029 etc.). This means load re-distribution on the anchors due to elastic deformations of the anchor plate are not considered - the
anchor plate is assumed to be sufficiently stiff, in order not to be deformed when subjected to the design loading. PROFIS Engineering
calculates the minimum required anchor plate thickness with CBFEM to limit the stress of the anchor plate based on the assumptions
explained above. The proof if the rigid anchor plate assumption is valid is not carried out by PROFIS Engineering. Input data and results
must be checked for agreement with the existing conditions and for plausibility!
• Checking the transfer of loads into the base material is required in accordance with EN 1992-4, Annex A!
• The design is only valid if the clearance hole in the fixture is not larger than the value given in Table 6.1 of EN 1992-4! For larger diameters
of the clearance hole see section 6.2.2 of EN 1992-4!
• The accessory list in this report is for the information of the user only. In any case, the instructions for use provided with the product have to
be followed to ensure a proper installation.
• For the determination of the y re,v (concrete edge failure) the minimum concrete cover defined in the design settings is used as the concrete
cover of the edge reinforcement.
• Characteristic bond resistances depend on short- and long-term temperatures.
• Edge reinforcement is not required to avoid splitting failure
• Design is only valid if hole is filled to remove clearance, clearance as per EN 1992-4 Table 6.1
• The characteristic bond resistances depend on the return period (service life in years): 100
Input data and results must be checked for conformity with the existing conditions and for plausibility!
PROFIS Engineering ( c ) 2003-2022 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
7
Hilti PROFIS Engineering 3.0.74
www.hilti.com.sg
Company: Page: 8
Address: Specifier:
Phone I Fax: | E-Mail:
Design: B25A TO EXISTING RC BEAM Date: 06/01/2022
Fastening point:
7 Installation data
2
Anchor plate, steel: S 235; E = 210,000.00 N/mm ; fyk = 235.00 N/mm
2 Anchor type and diameter: HIT-RE 500 V3 100 years +
HAS-U 8.8 HDG M16
Profile: I profile, ; (L x W x T x FT) = 254.0 mm x 146.0 mm x 6.4 mm x 10.9 Item number: 2223911 HAS-U 8.8 HDG M16x300
mm (element) / 2123403 HIT-RE 500 V3 (adhesive)
Hole diameter in the fixture: df = 18.0 mm Maximum installation torque: 80 Nm
Plate thickness (input): 16.0 mm Hole diameter in the base material: 18.0 mm
Recommended plate thickness: not calculated Hole depth in the base material: 150.0 mm
Drilling method: Hammer drilled Minimum thickness of the base material: 186.0 mm
Cleaning: Compressed air cleaning of the drilled hole according to instructions
for use is required
Hilti HAS-U threaded rod with HIT-RE 500 V3 injection mortar with 150 mm embedment h_ef, M16, Hot dip galvanized, Hammer drilled
installation per ETA 16/0143, with annular gaps filled with Hilti Filling set or any suitable gap solutions
-10.0
y
150.0 150.0
40.0
6 4 2
100.0
120.0
x
100.0
5 3 1
40.0 -0.0
-0.0
Input data and results must be checked for conformity with the existing conditions and for plausibility!
PROFIS Engineering ( c ) 2003-2022 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
8
Hilti PROFIS Engineering 3.0.74
www.hilti.com.sg
Company: Page: 9
Address: Specifier:
Phone I Fax: | E-Mail:
Design: B25A TO EXISTING RC BEAM Date: 06/01/2022
Fastening point:
8 Alternative fastening
8.1 Alternative fastening data
Anchor plate :
R lx x ly x t = 300.0 mm x 200.0 mm x 16.0 mm; (Recommended plate thickness: not calculated)
Input data and results must be checked for conformity with the existing conditions and for plausibility!
PROFIS Engineering ( c ) 2003-2022 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
9
Hilti PROFIS Engineering 3.0.74
www.hilti.com.sg
Company: Page: 10
Address: Specifier:
Phone I Fax: | E-Mail:
Design: B25A TO EXISTING RC BEAM Date: 06/01/2022
Fastening point:
Hilti HAS-U threaded rod with HVU2 capsule mortar with 125 mm embedment h_ef, M16_hef1, Hot dip galvanized, Hammer drilled
installation per ETA-16/0515, with annular gaps filled with Hilti Filling set or any suitable gap solutions
Input data and results must be checked for conformity with the existing conditions and for plausibility!
PROFIS Engineering ( c ) 2003-2022 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
10
Hilti PROFIS Engineering 3.0.74
www.hilti.com.sg
Company: Page: 11
Address: Specifier:
Phone I Fax: | E-Mail:
Design: B25A TO EXISTING RC BEAM Date: 06/01/2022
Fastening point:
Input data and results must be checked for conformity with the existing conditions and for plausibility!
PROFIS Engineering ( c ) 2003-2022 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
11
Hilti PROFIS Engineering 3.0.74
www.hilti.com.sg
Company: Page: 1
Address: Specifier:
Phone I Fax: | E-Mail:
Design: Concrete - Jan 6, 2022 Date: 05/01/2022
Fastening point:
Specifier's comments:
1 Input data
Anchor type and diameter: HIT-RE 500 V3 100 years + HAS-U 8.8 HDG M16
Return period (service life in years): 100
Item number: 2223911 HAS-U 8.8 HDG M16x300 (element) /
2123403 HIT-RE 500 V3 (adhesive)
Filling set or any suitable annular gap filling solution
Effective embedment depth: hef,act = 150.0 mm (hef,limit = - mm)
Material: 8.8
Evaluation Service Report: ETA 16/0143
Issued I Valid: 14/05/2019 | -
Proof: Design Method EN 1992-4, Chemical
Stand-off installation: eb = 0.0 mm (no stand-off); t = 16.0 mm
Anchor plate :
R lx x ly x t = 420.0 mm x 200.0 mm x 16.0 mm; (Recommended plate thickness: not calculated)
Application also possible with HVU2 + HAS-U 8.8 HDG M16_hef1 under the selected boundary conditions.
More information in section Alternative fastening data of this report.
R
- The anchor calculation is based on a rigid anchor plate assumption.
Input data and results must be checked for conformity with the existing conditions and for plausibility!
PROFIS Engineering ( c ) 2003-2022 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
1
Hilti PROFIS Engineering 3.0.74
www.hilti.com.sg
Company: Page: 2
Address: Specifier:
Phone I Fax: | E-Mail:
Design: Concrete - Jan 6, 2022 Date: 05/01/2022
Fastening point:
Anchor forces are calculated based on the assumption of a rigid anchor plate.
Input data and results must be checked for conformity with the existing conditions and for plausibility!
PROFIS Engineering ( c ) 2003-2022 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
2
Hilti PROFIS Engineering 3.0.74
www.hilti.com.sg
Company: Page: 3
Address: Specifier:
Phone I Fax: | E-Mail:
Design: Concrete - Jan 6, 2022 Date: 05/01/2022
Fastening point:
Input data and results must be checked for conformity with the existing conditions and for plausibility!
PROFIS Engineering ( c ) 2003-2022 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
3
Hilti PROFIS Engineering 3.0.74
www.hilti.com.sg
Company: Page: 4
Address: Specifier:
Phone I Fax: | E-Mail:
Design: Concrete - Jan 6, 2022 Date: 05/01/2022
Fastening point:
V
VEd £ VRd,s = Rk,s EN 1992-4, Table 7.2
gM,s
0
VRk,s = k7 · VRk,s EN 1992-4, Eq. (7.35)
0
VRk,s [kN] k7 VRk,s [kN] gM,s VRd,s [kN] VEd [kN]
62.800 1.000 62.800 1.250 50.240 8.333
Input data and results must be checked for conformity with the existing conditions and for plausibility!
PROFIS Engineering ( c ) 2003-2022 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
4
Hilti PROFIS Engineering 3.0.74
www.hilti.com.sg
Company: Page: 5
Address: Specifier:
Phone I Fax: | E-Mail:
Design: Concrete - Jan 6, 2022 Date: 05/01/2022
Fastening point:
V
VEd £ VRd,cp = Rk,cp EN 1992-4, Table 7.2
gM,c,p
VRk,cp = k8 · min {NRk,c; NRk,p} EN 1992-4, Eq. (7.39c)
0 A
NRk,p = NRk,p · 0p,N · y g,Np · y s,Np · y re,N · y ec1,Np · y ec2,Np EN 1992-4, Eq. (7.13)
Ap,N
0
NRk,p = y sus · t Rk · p · d · hef EN 1992-4, Eq. (7.14)
y sus =1 EN 1992-4, Eq. (7.14a)
scr,Np = 7.3 · d · √y sus · t Rk £ 3 · hef EN 1992-4, Eq. (7.15)
0,5
y g,Np
0
= y g,Np - (s s )
cr,Np
· (y g,Np - 1) ³ 1.00
0
EN 1992-4, Eq. (7.17)
1,5
0
y g,Np = √n - (√n - 1) · (tt ) Rk
Rk,c
³ 1.00 EN 1992-4, Eq. (7.18)
k3
t Rk,c = · √hef · fck EN 1992-4, Eq. (7.19)
p·d
c
y s,Np = 0.7 + 0.3 · 1.00 EN 1992-4, Eq. (7.20)
ccr,Np £
1
y ec1,Np = 1.00 EN 1992-4, Eq. (7.21)
2 · ec1,N £
1+ (
scr,Np )
1
y ec2,Np = 1.00 EN 1992-4, Eq. (7.21)
2 · ec2,N £
1+ (
scr,Np )
2 0 2 2 2
Ap,N [mm ] Ap,N [mm ] t Rk,ucr,20 [N/mm ] ccr,Np [mm] scr,Np [mm] cmin [mm] fc,cyl [N/mm ]
287,103 177,349 13.00 210.6 421.1 80.0 32.00
0
yc t Rk,cr [N/mm ]
2
k3 t Rk,c [N/mm ]
2
k8 y g,Np
Group anchor ID
1-6
Input data and results must be checked for conformity with the existing conditions and for plausibility!
PROFIS Engineering ( c ) 2003-2022 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
5
Hilti PROFIS Engineering 3.0.74
www.hilti.com.sg
Company: Page: 6
Address: Specifier:
Phone I Fax: | E-Mail:
Design: Concrete - Jan 6, 2022 Date: 05/01/2022
Fastening point:
V
VEd £ VRd,c = Rk,c EN 1992-4, Table 7.2
gM,c
0 Ac,V
VRk,c = kT · VRk,c · 0
· y s,V · y h,V · y a,V · y ec,V · y re,V EN 1992-4, Eq. (7.40)
Ac,V
0 a b 1,5
VRk,c = k9 · dnom · lf · √fck · c1 EN 1992-4, Eq. (7.41)
0,5
a = 0.1 · () lf
c1
EN 1992-4, Eq. (7.42)
0,2
= 0.1 · (
c )
d nom
b EN 1992-4, Eq. (7.43)
1
0 2
Ac,V = 4.5 · c1 EN 1992-4, Eq. (7.44)
c2
y s,V = 0.7 + 0.3 · 1.00 EN 1992-4, Eq. (7.45)
1.5 · c1 £
0,5
y h,V = (1.5h· c ) 1
³ 1.00 EN 1992-4, Eq. (7.46)
1
y ec,V = £ 1.00 EN 1992-4, Eq. (7.47)
1+ ( 2 · eV
3 · c1 )
y a,V = √(cos a ) + (10.5 · sin a )
V
2
V
2 ³ 1.00 EN 1992-4, Eq. (7.48)
Comments: Tension displacements are valid with half of the required installation torque moment for uncracked concrete! Shear displacements
are valid without friction between the concrete and the anchor plate! The gap due to the drilled hole and clearance hole tolerances are not
included in this calculation!
The acceptable anchor displacements depend on the fastened construction and must be defined by the designer!
Input data and results must be checked for conformity with the existing conditions and for plausibility!
PROFIS Engineering ( c ) 2003-2022 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
6
Hilti PROFIS Engineering 3.0.74
www.hilti.com.sg
Company: Page: 7
Address: Specifier:
Phone I Fax: | E-Mail:
Design: Concrete - Jan 6, 2022 Date: 05/01/2022
Fastening point:
6 Warnings
• The anchor design methods in PROFIS Engineering require rigid anchor plates per current regulations (AS 5216:2021, ETAG 001/Annex C,
EOTA TR029 etc.). This means load re-distribution on the anchors due to elastic deformations of the anchor plate are not considered - the
anchor plate is assumed to be sufficiently stiff, in order not to be deformed when subjected to the design loading. PROFIS Engineering
calculates the minimum required anchor plate thickness with CBFEM to limit the stress of the anchor plate based on the assumptions
explained above. The proof if the rigid anchor plate assumption is valid is not carried out by PROFIS Engineering. Input data and results
must be checked for agreement with the existing conditions and for plausibility!
• Checking the transfer of loads into the base material is required in accordance with EN 1992-4, Annex A!
• The design is only valid if the clearance hole in the fixture is not larger than the value given in Table 6.1 of EN 1992-4! For larger diameters
of the clearance hole see section 6.2.2 of EN 1992-4!
• The accessory list in this report is for the information of the user only. In any case, the instructions for use provided with the product have to
be followed to ensure a proper installation.
• For the determination of the y re,v (concrete edge failure) the minimum concrete cover defined in the design settings is used as the concrete
cover of the edge reinforcement.
• Characteristic bond resistances depend on short- and long-term temperatures.
• Edge reinforcement is not required to avoid splitting failure
• Design is only valid if hole is filled to remove clearance, clearance as per EN 1992-4 Table 6.1
• The characteristic bond resistances depend on the return period (service life in years): 100
Input data and results must be checked for conformity with the existing conditions and for plausibility!
PROFIS Engineering ( c ) 2003-2022 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
7
Hilti PROFIS Engineering 3.0.74
www.hilti.com.sg
Company: Page: 8
Address: Specifier:
Phone I Fax: | E-Mail:
Design: Concrete - Jan 6, 2022 Date: 05/01/2022
Fastening point:
7 Installation data
2
Anchor plate, steel: S 235; E = 210,000.00 N/mm ; fyk = 235.00 N/mm
2 Anchor type and diameter: HIT-RE 500 V3 100 years +
HAS-U 8.8 HDG M16
Profile: I profile, ; (L x W x T x FT) = 400.0 mm x 140.0 mm x 6.4 mm x 8.6 Item number: 2223911 HAS-U 8.8 HDG M16x300
mm (element) / 2123403 HIT-RE 500 V3 (adhesive)
Hole diameter in the fixture: df = 18.0 mm Maximum installation torque: 80 Nm
Plate thickness (input): 16.0 mm Hole diameter in the base material: 18.0 mm
Recommended plate thickness: not calculated Hole depth in the base material: 150.0 mm
Drilling method: Hammer drilled Minimum thickness of the base material: 186.0 mm
Cleaning: Compressed air cleaning of the drilled hole according to instructions
for use is required
Hilti HAS-U threaded rod with HIT-RE 500 V3 injection mortar with 150 mm embedment h_ef, M16, Hot dip galvanized, Hammer drilled
installation per ETA 16/0143, with annular gaps filled with Hilti Filling set or any suitable gap solutions
-10.0
y
210.0 210.0
40.0
6 4 2
100.0
120.0
x
100.0
5 3 1
40.0 -0.0
-0.0
Input data and results must be checked for conformity with the existing conditions and for plausibility!
PROFIS Engineering ( c ) 2003-2022 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
8
Hilti PROFIS Engineering 3.0.74
www.hilti.com.sg
Company: Page: 9
Address: Specifier:
Phone I Fax: | E-Mail:
Design: Concrete - Jan 6, 2022 Date: 05/01/2022
Fastening point:
8 Alternative fastening
8.1 Alternative fastening data
Anchor plate :
R lx x ly x t = 420.0 mm x 200.0 mm x 16.0 mm; (Recommended plate thickness: not calculated)
Input data and results must be checked for conformity with the existing conditions and for plausibility!
PROFIS Engineering ( c ) 2003-2022 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
9
Hilti PROFIS Engineering 3.0.74
www.hilti.com.sg
Company: Page: 10
Address: Specifier:
Phone I Fax: | E-Mail:
Design: Concrete - Jan 6, 2022 Date: 05/01/2022
Fastening point:
Hilti HAS-U threaded rod with HVU2 capsule mortar with 125 mm embedment h_ef, M16_hef1, Hot dip galvanized, Hammer drilled
installation per ETA-16/0515, with annular gaps filled with Hilti Filling set or any suitable gap solutions
Input data and results must be checked for conformity with the existing conditions and for plausibility!
PROFIS Engineering ( c ) 2003-2022 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
10
Hilti PROFIS Engineering 3.0.74
www.hilti.com.sg
Company: Page: 11
Address: Specifier:
Phone I Fax: | E-Mail:
Design: Concrete - Jan 6, 2022 Date: 05/01/2022
Fastening point:
Input data and results must be checked for conformity with the existing conditions and for plausibility!
PROFIS Engineering ( c ) 2003-2022 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
11
POB ROOF FRAME DESIGN
Job No Sheet No Rev
1
Software licensed to AECOM- CSS Part
CONNECTED User: Sujeevan Leonard Thamakulasingam
Job Title Ref
By Date21-Oct-21 Chd
Job Information
Engineer Checked Approved
Name:
Date: 21-Oct-21
Project ID
Project Name
Primary 1 DL
Primary 2 SDL
Primary 3 LL
Primary 4 WL
Primary 5 1.0DL+1.0LL
Primary 6 1.0DL+1.0WL
Primary 7 1.35DL+1.5LL
Primary 8 1.35DL+1.5WL
Section Properties
Prop Section Area Iyy Izz J Material
(cm2) (cm4) (cm4) (cm4)
1 TUB20020012.0 88.700 5.17E+3 5.17E+3 8.21E+3 STEEL
2 TUB1501508.0 44.800 1.49E+3 1.49E+3 2.35E+3 STEEL
3 TUBE 96.000 3.8E+3 14.7E+3 9.44E+3 STEEL
4 TUB40020010.0 115.000 8.08E+3 23.9E+3 19.3E+3 STEEL
Print Time/Date: 07/01/2022 09:37 STAAD.Pro CONNECT Edition 22.08.00.175 Print Run 1 of 87
Job No Sheet No Rev
2
Software licensed to AECOM- CSS Part
CONNECTED User: Sujeevan Leonard Thamakulasingam
Job Title Ref
By Date21-Oct-21 Chd
Materials
Mat Name E Density
(kN/mm2) (kg/m3) (/°C)
1 STEEL 205.000 0.300 7.83E+3 12E -6
2 CONCRETE 21.718 0.170 2.4E+3 10E -6
3 ALUMINUM 68.948 0.330 2.71E+3 23E -6
4 STAINLESSSTEEL 197.930 0.300 7.83E+3 18E -6
5 STEEL_36_KSI 199.948 0.300 7.83E+3 11.7E -6
6 STEEL_50_KSI 199.948 0.300 7.83E+3 11.7E -6
7 STEEL_275_NMM2 205.000 0.300 7.85E+3 12E -6
8 STEEL_355_NMM2 205.000 0.300 7.85E+3 12E -6
9 Q235 206.000 0.300 7.85E+3 12E -6
10 Q345 206.000 0.300 7.85E+3 12E -6
11 Q355 206.000 0.300 7.85E+3 12E -6
12 Q390 206.000 0.300 7.85E+3 12E -6
13 Q420 206.000 0.300 7.85E+3 12E -6
14 Q460 206.000 0.300 7.85E+3 12E -6
1 DL None
2 SDL None
3 LL None
4 WL None
5 1.0DL+1.0LL None
6 1.0DL+1.0WL None
7 1.35DL+1.5LL None
8 1.35DL+1.5WL None
Print Time/Date: 07/01/2022 09:37 STAAD.Pro CONNECT Edition 22.08.00.175 Print Run 2 of 87
Job No Sheet No Rev
3
Software licensed to AECOM- CSS Part
CONNECTED User: Sujeevan Leonard Thamakulasingam
Job Title Ref
By Date21-Oct-21 Chd
10.700m
3.250m
10.800m
3.250m
10.700m
8.000m
11.900m 7.400m
3.250m
Y
X
Z Load 1
Print Time/Date: 07/01/2022 09:37 STAAD.Pro CONNECT Edition 22.08.00.175 Print Run 3 of 87
Job No Sheet No Rev
4
Software licensed to AECOM- CSS Part
CONNECTED User: Sujeevan Leonard Thamakulasingam
Job Title Ref
By Date21-Oct-21 Chd
TUB40020010.0TUB1501508.0
TUB40020010.0 TUB20020012.0
TUB1501508.0 TUB40020010.0
TUB40020010.0 TUB1501508.0
TUB1501508.0
TUB40020010.0 TUB20020012.0
TUB1501508.0
TUB1501508.0 TUB40020010.0
TUB40020010.0
TUB1501508.0 TUB1501508.0
TUB20020012.0 TUB40020010.0 TUB20020012.0
TUB1501508.0 TUB1501508.0
TUB40020010.0
TUB20020012.0 TUB40020010.0
TUB1501508.0
TUB40020010.0
TUB1501508.0
TUB1501508.0
TUB20020012.0 TUB40020010.0 TUB40020010.0
TUB1501508.0
TUB40020010.0
TUB1501508.0
TUB40020010.0 TUB40020010.0
TUB1501508.0
TUB40020010.0
TUBE
TUB40020010.0
TUBE TUBE
TUB1501508.0
TUB1501508.0 TUBE
TUB20020012.0 TUB20020012.0
TUB1501508.0
TUB1501508.0 TUBE
TUB20020012.0
TUB20020012.0
Y TUB20020012.0
X
Z Load 1
MEMBER SIZES
Print Time/Date: 07/01/2022 09:37 STAAD.Pro CONNECT Edition 22.08.00.175 Print Run 4 of 87
Job No Sheet No Rev
5
Software licensed to AECOM- CSS Part
CONNECTED User: Sujeevan Leonard Thamakulasingam
Job Title Ref
By Date21-Oct-21 Chd
20
10
17
22
2 5 16
19
8 21
9
18 25
27
1 12 15
29
28 33
7
24
26 35
11 34 37
32 39
38
60
36
58 41
44 43
46 57
59
45
55
48 47
52
49
Y 56
X
Z Load 1
54
NODE NUMBERS
Print Time/Date: 07/01/2022 09:37 STAAD.Pro CONNECT Edition 22.08.00.175 Print Run 5 of 87
Job No Sheet No Rev
6
Software licensed to AECOM- CSS Part
CONNECTED User: Sujeevan Leonard Thamakulasingam
Job Title Ref
By Date21-Oct-21 Chd
23 16
5 3
25 27
4 17
20
69 7
26
11 24
22
21 30
1 15 10
12 34
13
6 32
33
35
29
43
8 31 39
42
40
48
38 45
47
46
55
44
73 72
70 49 57
71 51
59
58 50
53 52 68
60 66
54
67
Y 65
X
Z Load 1
BEAM NUMBERS
Print Time/Date: 07/01/2022 09:37 STAAD.Pro CONNECT Edition 22.08.00.175 Print Run 6 of 87
Job No Sheet No Rev
7
Software licensed to AECOM- CSS Part
CONNECTED User: Sujeevan Leonard Thamakulasingam
Job Title Ref
By Date21-Oct-21 Chd
-3.750 kN/m
-8.250 kN/m
-10.500 kN/m
-10.500 kN/m
-10.500 kN/m
-1.000 kN/m -1.000 kN/m
-1.000 kN/m
Y -1.000 kN/m
X
Z Load 2
-1.000 kN/m
SDL=2.5KPA
Print Time/Date: 07/01/2022 09:37 STAAD.Pro CONNECT Edition 22.08.00.175 Print Run 7 of 87
Job No Sheet No Rev
8
Software licensed to AECOM- CSS Part
CONNECTED User: Sujeevan Leonard Thamakulasingam
Job Title Ref
By Date21-Oct-21 Chd
-2.250 kN/m
-2.500 kN/m
-2.250 kN/m
-3.100 kN/m
-2.500 kN/m
-3.100 kN/m
-3.100 kN/m
-3.100 kN/m
-3.100 kN/m
-3.100 kN/m
-3.100 kN/m
-3.100 kN/m
Y
X
Z Load 3
LL=0.75KPA
Print Time/Date: 07/01/2022 09:37 STAAD.Pro CONNECT Edition 22.08.00.175 Print Run 8 of 87
Job No Sheet No Rev
9
Software licensed to AECOM- CSS Part
CONNECTED User: Sujeevan Leonard Thamakulasingam
Job Title Ref
By Date21-Oct-21 Chd
-1.000 kN/m
-2.200 kN/m
-2.600 kN/m
-2.600 kN/m
2.200 kN/m
-2.600 kN/m -2.600 kN/m
2.600 kN/m
-2.600 kN/m
2.600 kN/m
2.600 kN/m
Y
X 2.600 kN/m
Z Load 4
2.600 kN/m
WL
Print Time/Date: 07/01/2022 09:37 STAAD.Pro CONNECT Edition 22.08.00.175 Print Run 9 of 87
Job No Sheet No Rev
10
Software licensed to AECOM- CSS Part
CONNECTED User: Sujeevan Leonard Thamakulasingam
Job Title Ref
By Date21-Oct-21 Chd
0.149 0.0436
0.15 0.167
0.00728 0.234
0.145 0.0321
0.00896
0.234 0.295
0.0393 0.0115
0.223 0.283
0.0154 0.0151
0.168 0.283 0.358
0.033 0.0168
0.268
0.264 0.424
0.0256
0.424
0.0393
0.0131
0.323 0.397 0.422
0.0236
0.422
0.0125
0.396 0.526
0.0261
0.585
0.0825
0.587
0.354 0.362
0.0303 0.207
0.255
0.177
Y
X 0.156
Z Load 4 : Displacement
UTILIZATION RATIO
Print Time/Date: 07/01/2022 09:37 STAAD.Pro CONNECT Edition 22.08.00.175 Print Run 10 of 87
Job No Sheet No Rev
11
Software licensed to AECOM- CSS Part
CONNECTED User: Sujeevan Leonard Thamakulasingam
Job Title Ref
By Date21-Oct-21 Chd
Y
X
Z Load 4 : Bending Z
Print Time/Date: 07/01/2022 09:37 STAAD.Pro CONNECT Edition 22.08.00.175 Print Run 11 of 87
Job No Sheet No Rev
12
Software licensed to AECOM- CSS Part
CONNECTED User: Sujeevan Leonard Thamakulasingam
Job Title Ref
By Date21-Oct-21 Chd
Y
X
Z Load 4 : Shear Y
SHEARFORCE DIAGRAM
Print Time/Date: 07/01/2022 09:37 STAAD.Pro CONNECT Edition 22.08.00.175 Print Run 12 of 87
Job No Sheet No Rev
13
Software licensed to AECOM- CSS Part
CONNECTED User: Sujeevan Leonard Thamakulasingam
Job Title Ref
By Date21-Oct-21 Chd
Reactions
Horizontal Vertical Horizontal Moment
Node L/C FX FY FZ MX MY MZ
(kN) (kN) (kN) (kN-m) (kN-m) (kN-m)
1 1:DL 1.629 8.363 0.060 0 0 0
2:SDL 3.711 17.917 0.023 0 0 0
3:LL 2.124 8.760 0.004 0 0 0
4:WL -1.843 3.114 0.004 0 0 0
5:1.0DL+1.0LL 7.463 35.039 0.087 0 0 0
6:1.0DL+1.0WL 3.487 29.377 0.087 0 0 0
7:1.35DL+1.5LL 10.392 48.617 0.118 0 0 0
8:1.35DL+1.5WL 4.422 40.112 0.118 0 0 0
5 1:DL -1.613 8.302 0.060 0 0 0
2:SDL -3.536 18.290 0.018 0 0 0
3:LL -2.083 9.027 0.002 0 0 0
4:WL -2.335 4.806 0.006 0 0 0
5:1.0DL+1.0LL -7.230 35.618 0.079 0 0 0
6:1.0DL+1.0WL -7.494 31.413 0.083 0 0 0
7:1.35DL+1.5LL -10.072 49.436 0.107 0 0 0
8:1.35DL+1.5WL -10.475 43.139 0.113 0 0 0
7 1:DL 1.865 9.731 0.010 0 0 0
Print Time/Date: 07/01/2022 09:37 STAAD.Pro CONNECT Edition 22.08.00.175 Print Run 13 of 87
Job No Sheet No Rev
14
Software licensed to AECOM- CSS Part
CONNECTED User: Sujeevan Leonard Thamakulasingam
Job Title Ref
By Date21-Oct-21 Chd
Reactions Cont...
Horizontal Vertical Horizontal Moment
Node L/C FX FY FZ MX MY MZ
(kN) (kN) (kN) (kN-m) (kN-m) (kN-m)
2:SDL 7.602 35.266 0.029 0 0 0
3:LL 2.337 9.711 0.006 0 0 0
4:WL -2.825 7.631 0.005 0 0 0
5:1.0DL+1.0LL 11.804 54.709 0.045 0 0 0
6:1.0DL+1.0WL 6.649 52.610 0.043 0 0 0
7:1.35DL+1.5LL 16.285 75.314 0.061 0 0 0
8:1.35DL+1.5WL 8.557 72.153 0.059 0 0 0
9 1:DL -1.861 9.618 0.009 0 0 0
2:SDL -7.617 36.357 0.023 0 0 0
3:LL -2.334 10.037 0.004 0 0 0
4:WL -3.731 9.734 0.007 0 0 0
5:1.0DL+1.0LL -11.811 56.011 0.036 0 0 0
6:1.0DL+1.0WL -13.206 55.728 0.038 0 0 0
7:1.35DL+1.5LL -16.295 77.119 0.049 0 0 0
8:1.35DL+1.5WL -18.384 76.708 0.052 0 0 0
11 1:DL 1.968 10.438 0.078 0 0 0
2:SDL 9.649 43.965 0.003 0 0 0
3:LL 2.853 12.022 0.001 0 0 0
4:WL -3.173 9.112 -0.000 0 0 0
5:1.0DL+1.0LL 14.468 66.419 0.082 0 0 0
6:1.0DL+1.0WL 8.458 63.488 0.080 0 0 0
7:1.35DL+1.5LL 19.957 91.463 0.110 0 0 0
8:1.35DL+1.5WL 10.953 87.052 0.108 0 0 0
15 1:DL -1.975 10.306 0.077 0 0 0
2:SDL -9.788 45.428 -0.001 0 0 0
3:LL -2.891 12.452 0.000 0 0 0
4:WL -4.275 11.418 -0.000 0 0 0
5:1.0DL+1.0LL -14.652 68.180 0.076 0 0 0
6:1.0DL+1.0WL -16.027 67.169 0.076 0 0 0
7:1.35DL+1.5LL -20.211 93.906 0.103 0 0 0
8:1.35DL+1.5WL -22.266 92.404 0.102 0 0 0
24 1:DL -0.029 0.585 0.524 0 0 0
2:SDL -0.153 0.007 4.197 0 0 0
3:LL -0.045 0.002 1.235 0 0 0
4:WL -0.364 0.002 0.636 0 0 0
5:1.0DL+1.0LL -0.228 0.594 5.972 0 0 0
6:1.0DL+1.0WL -0.558 0.593 5.362 0 0 0
7:1.35DL+1.5LL -0.316 0.802 8.266 0 0 0
8:1.35DL+1.5WL -0.818 0.802 7.343 0 0 0
25 1:DL 0.016 0.585 0.257 0 0 0
2:SDL 0.131 0.008 2.481 0 0 0
3:LL 0.038 0.002 0.742 0 0 0
4:WL -0.304 0.002 0.643 0 0 0
5:1.0DL+1.0LL 0.187 0.595 3.489 0 0 0
Print Time/Date: 07/01/2022 09:37 STAAD.Pro CONNECT Edition 22.08.00.175 Print Run 14 of 87
Job No Sheet No Rev
15
Software licensed to AECOM- CSS Part
CONNECTED User: Sujeevan Leonard Thamakulasingam
Job Title Ref
By Date21-Oct-21 Chd
Reactions Cont...
Horizontal Vertical Horizontal Moment
Node L/C FX FY FZ MX MY MZ
(kN) (kN) (kN) (kN-m) (kN-m) (kN-m)
6:1.0DL+1.0WL -0.165 0.595 3.391 0 0 0
7:1.35DL+1.5LL 0.259 0.804 4.833 0 0 0
8:1.35DL+1.5WL -0.276 0.803 4.688 0 0 0
26 1:DL 0.000 6.570 0.120 0 0 0
2:SDL -0.000 40.796 0.759 0 0 0
3:LL -0.000 12.043 0.224 0 0 0
4:WL 0.000 10.100 0.164 0 0 0
5:1.0DL+1.0LL -0.000 59.418 1.107 0 0 0
6:1.0DL+1.0WL 0.004 57.474 1.047 0 0 0
7:1.35DL+1.5LL -0.000 82.029 1.533 0 0 0
8:1.35DL+1.5WL 0.007 79.112 1.443 0 0 0
27 1:DL 0.000 6.427 0.047 0 0 0
2:SDL -0.000 42.167 0.301 0 0 0
3:LL -0.000 12.448 0.088 0 0 0
4:WL 0.000 10.440 0.046 0 0 0
5:1.0DL+1.0LL -0.000 61.047 0.437 0 0 0
6:1.0DL+1.0WL 0.002 59.039 0.395 0 0 0
7:1.35DL+1.5LL -0.000 84.287 0.606 0 0 0
8:1.35DL+1.5WL 0.005 81.274 0.542 0 0 0
32 1:DL 0.000 6.476 0.127 0 0 0
2:SDL 0.000 40.778 0.800 0 0 0
3:LL 0.000 12.041 0.236 0 0 0
4:WL 0.000 10.100 0.171 0 0 0
5:1.0DL+1.0LL 0.000 59.288 1.167 0 0 0
6:1.0DL+1.0WL 0.000 57.353 1.101 0 0 0
7:1.35DL+1.5LL 0.000 81.834 1.615 0 0 0
8:1.35DL+1.5WL 0.000 78.936 1.517 0 0 0
33 1:DL 0.000 6.341 0.044 0 0 0
2:SDL 0.000 42.157 0.279 0 0 0
3:LL 0.000 12.447 0.081 0 0 0
4:WL 0.000 10.440 0.043 0 0 0
5:1.0DL+1.0LL 0.000 60.940 0.406 0 0 0
6:1.0DL+1.0WL 0.000 58.936 0.367 0 0 0
7:1.35DL+1.5LL 0.000 84.130 0.563 0 0 0
8:1.35DL+1.5WL 0.000 81.127 0.504 0 0 0
36 1:DL -0.997 6.526 0.135 0 0 0
2:SDL -9.547 51.072 0.856 0 0 0
3:LL -2.817 15.053 0.251 0 0 0
4:WL -4.567 8.460 0.181 0 0 0
5:1.0DL+1.0LL -13.369 72.765 1.250 0 0 0
6:1.0DL+1.0WL -15.136 66.148 1.179 0 0 0
7:1.35DL+1.5LL -18.481 100.629 1.735 0 0 0
8:1.35DL+1.5WL -21.138 90.686 1.629 0 0 0
37 1:DL -0.527 6.077 0.039 0 0 0
Print Time/Date: 07/01/2022 09:37 STAAD.Pro CONNECT Edition 22.08.00.175 Print Run 15 of 87
Job No Sheet No Rev
16
Software licensed to AECOM- CSS Part
CONNECTED User: Sujeevan Leonard Thamakulasingam
Job Title Ref
By Date21-Oct-21 Chd
Reactions Cont...
Horizontal Vertical Horizontal Moment
Node L/C FX FY FZ MX MY MZ
(kN) (kN) (kN) (kN-m) (kN-m) (kN-m)
2:SDL -5.046 47.543 0.249 0 0 0
3:LL -1.489 14.034 0.073 0 0 0
4:WL -2.414 9.569 0.037607 0 0 0
5:1.0DL+1.0LL -7.067 67.665 0.362 0 0 0
6:1.0DL+1.0WL -8.000 63.185 0.326 0 0 0
7:1.35DL+1.5LL -9.768 93.464 0.500 0 0 0
8:1.35DL+1.5WL -11.173 86.734 0.445 0 0 0
46 1:DL -0.550 10.825 -1.758 0 0 0
2:SDL -7.971 63.483 -11.010 0 0 0
3:LL -2.357 17.794 -3.250 0 0 0
4:WL -1.563 3.790 -1.463 0 0 0
5:1.0DL+1.0LL -10.861 92.052 -16.024 0 0 0
6:1.0DL+1.0WL -10.052 78.097 -14.236 0 0 0
7:1.35DL+1.5LL -14.997 126.883 -22.127 0 0 0
8:1.35DL+1.5WL -13.774 105.978 -19.443 0 0 0
47 1:DL -0.597 6.040 0.285 0 0 0
2:SDL -8.031 36.926 1.288 0 0 0
3:LL -2.371 9.944 0.383 0 0 0
4:WL -2.224 1.289 0.357 0 0 0
5:1.0DL+1.0LL -10.997 52.903 1.944 0 0 0
6:1.0DL+1.0WL -10.854 44.292 1.925 0 0 0
7:1.35DL+1.5LL -15.199 72.902 2.669 0 0 0
8:1.35DL+1.5WL -14.985 60.010 2.645 0 0 0
48 1:DL 0.538 6.423 -0.010 0 0 0
2:SDL 7.713 40.712 -0.012 0 0 0
3:LL 2.278 11.062 -0.004 0 0 0
4:WL -5.402 -1.344 -0.293 0 0 0
5:1.0DL+1.0LL 10.527 58.191 -0.026 0 0 0
6:1.0DL+1.0WL 2.854 45.762 -0.321 0 0 0
7:1.35DL+1.5LL 14.550 80.208 -0.036 0 0 0
8:1.35DL+1.5WL 3.042 61.554 -0.482 0 0 0
49 1:DL 0.555 6.623 0.121 0 0 0
2:SDL 7.805 41.852 0.662 0 0 0
3:LL 2.306 11.397 0.195 0 0 0
4:WL -5.974 -1.784 -0.191 0 0 0
5:1.0DL+1.0LL 10.659 59.870 0.978 0 0 0
6:1.0DL+1.0WL 2.393 46.649 0.587 0 0 0
7:1.35DL+1.5LL 14.729 82.532 1.349 0 0 0
8:1.35DL+1.5WL 2.334 62.679 0.759 0 0 0
54 1:DL 0.327 5.181 -0.071 0 0 0
2:SDL 4.759 34.080 0.261 0 0 0
3:LL 1.405 9.104 0.078 0 0 0
4:WL -6.181 -2.216 -0.145 0 0 0
5:1.0DL+1.0LL 6.491 48.354 0.265 0 0 0
Print Time/Date: 07/01/2022 09:37 STAAD.Pro CONNECT Edition 22.08.00.175 Print Run 16 of 87
Job No Sheet No Rev
17
Software licensed to AECOM- CSS Part
CONNECTED User: Sujeevan Leonard Thamakulasingam
Job Title Ref
By Date21-Oct-21 Chd
Reactions Cont...
Horizontal Vertical Horizontal Moment
Node L/C FX FY FZ MX MY MZ
(kN) (kN) (kN) (kN-m) (kN-m) (kN-m)
6:1.0DL+1.0WL -1.101 36.997 0.043 0 0 0
7:1.35DL+1.5LL 8.973 66.632 0.366 0 0 0
8:1.35DL+1.5WL -2.419 49.577 0.032 0 0 0
56 1:DL -0.317 5.535 -0.108 0 0 0
2:SDL -4.803 35.543 -0.184 0 0 0
3:LL -1.420 9.535 -0.051 0 0 0
4:WL -2.509 2.210 0.143 0 0 0
5:1.0DL+1.0LL -6.534 50.607 -0.357 0 0 0
6:1.0DL+1.0WL -7.633 43.336 -0.153 0 0 0
7:1.35DL+1.5LL -9.025 69.744 -0.506 0 0 0
8:1.35DL+1.5WL -10.678 58.868 -0.194 0 0 0
59 1:DL 1.569 6.871 -0.046 0 0 0
2:SDL 15.122 50.605 -1.020 0 0 0
3:LL 4.466 13.989 -0.299 0 0 0
4:WL -2.967 0.566 -0.351 0 0 0
5:1.0DL+1.0LL 21.152 71.431 -1.375 0 0 0
6:1.0DL+1.0WL 13.729 57.991 -1.421 0 0 0
7:1.35DL+1.5LL 29.220 98.491 -1.912 0 0 0
8:1.35DL+1.5WL 18.091 78.320 -1.977 0 0 0
Utilization Ratio
Beam Analysis Design Actual Allowable Ratio Clause L/C Ax Iz Iy Ix
Property Property Ratio Ratio (Act./Allow.) (cm2) (cm4) (cm4) (cm4)
1 TUB20020012.0
TUB20020012.0 0.168 1.000 0.168 EC-6.3.3-662 7 88.700 5.17E+3 5.17E+3 8.21E+3
3 TUB20020012.0
TUB20020012.0 0.167 1.000 0.167 EC-6.3.3-662 8 88.700 5.17E+3 5.17E+3 8.21E+3
4 TUB40020010.0
TUB40020010.0 0.145 1.000 0.145 EC-6.2.9.2/3 7 115.000 23.9E+3 8.08E+3 19.3E+3
5 TUB40020010.0
TUB40020010.0 0.150 1.000 0.150 EC-6.2.9.2/3 7 115.000 23.9E+3 8.08E+3 19.3E+3
6 TUB20020012.0
TUB20020012.0 0.264 1.000 0.264 EC-6.3.3-662 7 88.700 5.17E+3 5.17E+3 8.21E+3
7 TUB20020012.0
TUB20020012.0 0.295 1.000 0.295 EC-6.3.3-662 8 88.700 5.17E+3 5.17E+3 8.21E+3
8 TUB20020012.0
TUB20020012.0 0.323 1.000 0.323 EC-6.3.3-662 7 88.700 5.17E+3 5.17E+3 8.21E+3
10 TUB20020012.0
TUB20020012.0 0.358 1.000 0.358 EC-6.3.3-662 8 88.700 5.17E+3 5.17E+3 8.21E+3
11 TUB1501508.0
TUB1501508.0 0.039 1.000 0.039 EC-6.2.9.1 7 44.800 1.49E+3 1.49E+3 2.35E+3
12 TUB1501508.0
TUB1501508.0 0.033 1.000 0.033 EC-6.2.9.1 7 44.800 1.49E+3 1.49E+3 2.35E+3
13 TUB40020010.0
TUB40020010.0 0.268 1.000 0.268 EC-6.2.9.2/3 7 115.000 23.9E+3 8.08E+3 19.3E+3
15 TUB40020010.0
TUB40020010.0 0.283 1.000 0.283 EC-6.2.9.2/3 7 115.000 23.9E+3 8.08E+3 19.3E+3
16 TUB1501508.0
TUB1501508.0 0.044 1.000 0.044 EC-6.2.9.1 8 44.800 1.49E+3 1.49E+3 2.35E+3
17 TUB1501508.0
TUB1501508.0 0.032 1.000 0.032 EC-6.2.9.1 8 44.800 1.49E+3 1.49E+3 2.35E+3
20 TUB1501508.0
TUB1501508.0 0.009 1.000 0.009 EC-6.3.3-662 7 44.800 1.49E+3 1.49E+3 2.35E+3
21 TUB1501508.0
TUB1501508.0 0.015 1.000 0.015 EC-6.3.3-662 7 44.800 1.49E+3 1.49E+3 2.35E+3
22 TUB40020010.0
TUB40020010.0 0.223 1.000 0.223 EC-6.2.9.2/3 7 115.000 23.9E+3 8.08E+3 19.3E+3
23 TUB40020010.0
TUB40020010.0 0.149 1.000 0.149 EC-6.2.9.2/3 7 115.000 23.9E+3 8.08E+3 19.3E+3
24 TUB40020010.0
TUB40020010.0 0.283 1.000 0.283 EC-6.2.9.2/3 7 115.000 23.9E+3 8.08E+3 19.3E+3
Print Time/Date: 07/01/2022 09:37 STAAD.Pro CONNECT Edition 22.08.00.175 Print Run 17 of 87
Job No Sheet No Rev
18
Software licensed to AECOM- CSS Part
CONNECTED User: Sujeevan Leonard Thamakulasingam
Job Title Ref
By Date21-Oct-21 Chd
Failed Members
There is no data of this type.
Print Time/Date: 07/01/2022 09:37 STAAD.Pro CONNECT Edition 22.08.00.175 Print Run 18 of 87
Job No Sheet No Rev
19
Software licensed to AECOM- CSS Part
CONNECTED User: Sujeevan Leonard Thamakulasingam
Job Title Ref
By Date21-Oct-21 Chd
z-axis y-axis
Moment of inertia : 5171.000 5171.000
Plastic modulus : 621.000 621.000
Elastic modulus : 517.100 517.100
Shear Area : 44.350 44.350
Radius of gyration : 7.635 7.635
Effective Length : 325.000 325.000
z-axis y-axis
Slenderness ratio (KL/r) : 42.6 42.6
Compression Capacity : 2851.4 2851.4
Tension Capacity : 3129.3 3129.3
Moment Capacity : 220.5 220.5
Reduced Moment Capacity : 220.5 220.5
Shear Capacity : 909.0 909.0
Print Time/Date: 07/01/2022 09:37 STAAD.Pro CONNECT Edition 22.08.00.175 Print Run 19 of 87
Job No Sheet No Rev
20
Software licensed to AECOM- CSS Part
CONNECTED User: Sujeevan Leonard Thamakulasingam
Job Title Ref
By Date21-Oct-21 Chd
z-axis y-axis
Moment of inertia : 5171.000 5171.000
Plastic modulus : 621.000 621.000
Elastic modulus : 517.100 517.100
Shear Area : 44.350 44.350
Radius of gyration : 7.635 7.635
Effective Length : 325.000 325.000
z-axis y-axis
Slenderness ratio (KL/r) : 42.6 42.6
Compression Capacity : 2851.4 2851.4
Tension Capacity : 3129.3 3129.3
Moment Capacity : 220.5 220.5
Reduced Moment Capacity : 220.5 220.5
Shear Capacity : 909.0 909.0
Print Time/Date: 07/01/2022 09:37 STAAD.Pro CONNECT Edition 22.08.00.175 Print Run 20 of 87
Job No Sheet No Rev
21
Software licensed to AECOM- CSS Part
CONNECTED User: Sujeevan Leonard Thamakulasingam
Job Title Ref
By Date21-Oct-21 Chd
z-axis y-axis
Moment of inertia : 23910.004 8084.001
Plastic modulus : 1480.000 911.000
Elastic modulus : 1195.500 808.400
Shear Area : 38.333 76.667
Radius of gyration : 14.419 8.384
Effective Length : 370.000 370.000
z-axis y-axis
Slenderness ratio (KL/r) : 25.7 44.1
Compression Capacity : 3725.6 3469.1
Tension Capacity : 4057.2 4057.2
Moment Capacity : 417.5 264.4
Reduced Moment Capacity : 417.5 264.
Print Time/Date: 07/01/2022 09:37 STAAD.Pro CONNECT Edition 22.08.00.175 Print Run 21 of 87
Job No Sheet No Rev
22
Software licensed to AECOM- CSS Part
CONNECTED User: Sujeevan Leonard Thamakulasingam
Job Title Ref
By Date21-Oct-21 Chd
z-axis y-axis
Moment of inertia : 23910.004 8084.001
Plastic modulus : 1480.000 911.000
Elastic modulus : 1195.500 808.400
Shear Area : 38.333 76.667
Radius of gyration : 14.419 8.384
Effective Length : 280.000 280.00
Print Time/Date: 07/01/2022 09:37 STAAD.Pro CONNECT Edition 22.08.00.175 Print Run 22 of 87
Job No Sheet No Rev
23
Software licensed to AECOM- CSS Part
CONNECTED User: Sujeevan Leonard Thamakulasingam
Job Title Ref
By Date21-Oct-21 Chd
z-axis y-axis
Slenderness ratio (KL/r) : 19.4 33.4
Compression Capacity : 3795.7 3629.7
Tension Capacity : 4057.2 4057.2
Moment Capacity : 417.5 264.4
Reduced Moment Capacity : 417.5 264.4
Shear Capacity : 785.7 1571.4
Print Time/Date: 07/01/2022 09:37 STAAD.Pro CONNECT Edition 22.08.00.175 Print Run 23 of 87
Job No Sheet No Rev
24
Software licensed to AECOM- CSS Part
CONNECTED User: Sujeevan Leonard Thamakulasingam
Job Title Ref
By Date21-Oct-21 Chd
z-axis y-axis
Moment of inertia : 5171.000 5171.000
Plastic modulus : 621.000 621.000
Elastic modulus : 517.100 517.100
Shear Area : 44.350 44.350
Radius of gyration : 7.635 7.635
Effective Length : 325.000 325.000
z-axis y-axis
Slenderness ratio (KL/r) : 42.6 42.6
Compression Capacity : 2851.4 2851.4
Tension Capacity : 3129.3 3129.3
Moment Capacity : 220.5 220.5
Reduced Moment Capacity : 220.5 220.5
Shear Capacity : 909.0 909.0
Print Time/Date: 07/01/2022 09:37 STAAD.Pro CONNECT Edition 22.08.00.175 Print Run 24 of 87
Job No Sheet No Rev
25
Software licensed to AECOM- CSS Part
CONNECTED User: Sujeevan Leonard Thamakulasingam
Job Title Ref
By Date21-Oct-21 Chd
z-axis y-axis
Moment of inertia : 5171.000 5171.000
Plastic modulus : 621.000 621.000
Elastic modulus : 517.100 517.100
Shear Area : 44.350 44.350
Radius of gyration : 7.635 7.635
Effective Length : 325.000 325.000
z-axis y-axis
Slenderness ratio (KL/r) : 42.6 42.6
Compression Capacity : 2851.4 2851.4
Tension Capacity : 3129.3 3129.3
Moment Capacity : 220.5 220.5
Reduced Moment Capacity : 220.5 220.5
Shear Capacity : 909.0 909.0
Print Time/Date: 07/01/2022 09:37 STAAD.Pro CONNECT Edition 22.08.00.175 Print Run 25 of 87
Job No Sheet No Rev
26
Software licensed to AECOM- CSS Part
CONNECTED User: Sujeevan Leonard Thamakulasingam
Job Title Ref
By Date21-Oct-21 Chd
z-axis y-axis
Moment of inertia : 5171.000 5171.000
Plastic modulus : 621.000 621.000
Elastic modulus : 517.100 517.100
Shear Area : 44.350 44.350
Radius of gyration : 7.635 7.635
Effective Length : 325.000 325.000
z-axis y-axis
Slenderness ratio (KL/r) : 42.6 42.6
Compression Capacity : 2851.4 2851.4
Tension Capacity : 3129.3 3129.3
Moment Capacity : 220.5 220.5
Reduced Moment Capacity : 220.5 220.5
Shear Capacity : 909.0 909.0
Print Time/Date: 07/01/2022 09:37 STAAD.Pro CONNECT Edition 22.08.00.175 Print Run 26 of 87
Job No Sheet No Rev
27
Software licensed to AECOM- CSS Part
CONNECTED User: Sujeevan Leonard Thamakulasingam
Job Title Ref
By Date21-Oct-21 Chd
z-axis y-axis
Moment of inertia : 5171.000 5171.000
Plastic modulus : 621.000 621.000
Elastic modulus : 517.100 517.100
Shear Area : 44.350 44.350
Radius of gyration : 7.635 7.635
Effective Length : 325.000 325.000
z-axis y-axis
Slenderness ratio (KL/r) : 42.6 42.6
Compression Capacity : 2851.4 2851.4
Tension Capacity : 3129.3 3129.3
Moment Capacity : 220.5 220.5
Reduced Moment Capacity : 220.5 220.5
Shear Capacity : 909.0 909.0
Print Time/Date: 07/01/2022 09:37 STAAD.Pro CONNECT Edition 22.08.00.175 Print Run 27 of 87
Job No Sheet No Rev
28
Software licensed to AECOM- CSS Part
CONNECTED User: Sujeevan Leonard Thamakulasingam
Job Title Ref
By Date21-Oct-21 Chd
z-axis y-axis
Moment of inertia : 1491.000 1491.000
Plastic modulus : 237.000 237.000
Elastic modulus : 198.800 198.800
Shear Area : 22.400 22.400
Radius of gyration : 5.769 5.769
Effective Length : 300.000 300.000
z-axis y-axis
Slenderness ratio (KL/r) : 52.0 52.0
Compression Capacity : 1362.4 1362.4
Tension Capacity : 1580.5 1580.5
Moment Capacity : 84.1 84.1
Reduced Moment Capacity : 84.1 84.1
Shear Capacity : 459.1 459.1
Print Time/Date: 07/01/2022 09:37 STAAD.Pro CONNECT Edition 22.08.00.175 Print Run 28 of 87
Job No Sheet No Rev
29
Software licensed to AECOM- CSS Part
CONNECTED User: Sujeevan Leonard Thamakulasingam
Job Title Ref
By Date21-Oct-21 Chd
z-axis y-axis
Moment of inertia : 1491.000 1491.000
Plastic modulus : 237.000 237.000
Elastic modulus : 198.800 198.800
Shear Area : 22.400 22.400
Radius of gyration : 5.769 5.769
Effective Length : 360.000 360.000
z-axis y-axis
Slenderness ratio (KL/r) : 62.4 62.4
Compression Capacity : 1250.0 1250.
Print Time/Date: 07/01/2022 09:37 STAAD.Pro CONNECT Edition 22.08.00.175 Print Run 29 of 87
Job No Sheet No Rev
30
Software licensed to AECOM- CSS Part
CONNECTED User: Sujeevan Leonard Thamakulasingam
Job Title Ref
By Date21-Oct-21 Chd
z-axis y-axis
Moment of inertia : 23910.004 8084.001
Plastic modulus : 1480.000 911.000
Elastic modulus : 1195.500 808.400
Shear Area : 38.333 76.667
Radius of gyration : 14.419 8.384
Effective Length : 370.000 370.000
Print Time/Date: 07/01/2022 09:37 STAAD.Pro CONNECT Edition 22.08.00.175 Print Run 30 of 87
Job No Sheet No Rev
31
Software licensed to AECOM- CSS Part
CONNECTED User: Sujeevan Leonard Thamakulasingam
Job Title Ref
By Date21-Oct-21 Chd
z-axis y-axis
Slenderness ratio (KL/r) : 25.7 44.1
Compression Capacity : 3725.6 3469.1
Tension Capacity : 4057.2 4057.2
Moment Capacity : 417.5 264.4
Reduced Moment Capacity : 417.5 264.4
Shear Capacity : 785.7 1571.4
Print Time/Date: 07/01/2022 09:37 STAAD.Pro CONNECT Edition 22.08.00.175 Print Run 31 of 87
Job No Sheet No Rev
32
Software licensed to AECOM- CSS Part
CONNECTED User: Sujeevan Leonard Thamakulasingam
Job Title Ref
By Date21-Oct-21 Chd
z-axis y-axis
Moment of inertia : 23910.004 8084.001
Plastic modulus : 1480.000 911.000
Elastic modulus : 1195.500 808.400
Shear Area : 38.333 76.667
Radius of gyration : 14.419 8.384
Effective Length : 280.000 280.000
z-axis y-axis
Slenderness ratio (KL/r) : 19.4 33.4
Compression Capacity : 3795.7 3629.7
Tension Capacity : 4057.2 4057.2
Moment Capacity : 417.5 264.4
Reduced Moment Capacity : 417.5 264.4
Shear Capacity : 785.7 1571.4
Print Time/Date: 07/01/2022 09:37 STAAD.Pro CONNECT Edition 22.08.00.175 Print Run 32 of 87
Job No Sheet No Rev
33
Software licensed to AECOM- CSS Part
CONNECTED User: Sujeevan Leonard Thamakulasingam
Job Title Ref
By Date21-Oct-21 Chd
=======================================================================
16 ST TUB1501508.0 (BRITISH SECTIONS)
PASS EC-6.2.9.1 0.044 8
1.56 T -3.67 0.37 0.00
=======================================================================
MATERIAL DATA
Grade of steel = S 355
Modulus of elasticity = 205 kN/mm2
Design Strength (py) = 355 N/mm2
z-axis y-axis
Moment of inertia : 1491.000 1491.000
Plastic modulus : 237.000 237.000
Elastic modulus : 198.800 198.800
Shear Area : 22.400 22.400
Radius of gyration : 5.769 5.769
Effective Length : 300.000 300.000
z-axis y-axis
Slenderness ratio (KL/r) : 52.0 52.0
Compression Capacity : 1362.4 1362.4
Tension Capacity : 1580.5 1580.5
Moment Capacity : 84.1 84.1
Reduced Moment Capacity : 84.1 84.1
Shear Capacity : 459.1 459.1
Print Time/Date: 07/01/2022 09:37 STAAD.Pro CONNECT Edition 22.08.00.175 Print Run 33 of 87
Job No Sheet No Rev
34
Software licensed to AECOM- CSS Part
CONNECTED User: Sujeevan Leonard Thamakulasingam
Job Title Ref
By Date21-Oct-21 Chd
z-axis y-axis
Moment of inertia : 1491.000 1491.000
Plastic modulus : 237.000 237.000
Elastic modulus : 198.800 198.800
Shear Area : 22.400 22.400
Radius of gyration : 5.769 5.769
Effective Length : 360.000 360.000
z-axis y-axis
Slenderness ratio (KL/r) : 62.4 62.4
Compression Capacity : 1250.0 1250.0
Tension Capacity : 1580.5 1580.5
Moment Capacity : 84.1 84.1
Reduced Moment Capacity : 84.1 84.1
Shear Capacity : 459.1 459.1
Print Time/Date: 07/01/2022 09:37 STAAD.Pro CONNECT Edition 22.08.00.175 Print Run 34 of 87
Job No Sheet No Rev
35
Software licensed to AECOM- CSS Part
CONNECTED User: Sujeevan Leonard Thamakulasingam
Job Title Ref
By Date21-Oct-21 Chd
z-axis y-axis
Moment of inertia : 1491.000 1491.000
Plastic modulus : 237.000 237.000
Elastic modulus : 198.800 198.800
Shear Area : 22.400 22.400
Radius of gyration : 5.769 5.769
Effective Length : 300.000 300.000
z-axis y-axis
Slenderness ratio (KL/r) : 52.0 52.0
Compression Capacity : 1362.4 1362.4
Tension Capacity : 1580.5 1580.5
Moment Capacity : 84.1 84.1
Reduced Moment Capacity : 84.1 84.1
Shear Capacity : 459.1 459.1
Print Time/Date: 07/01/2022 09:37 STAAD.Pro CONNECT Edition 22.08.00.175 Print Run 35 of 87
Job No Sheet No Rev
36
Software licensed to AECOM- CSS Part
CONNECTED User: Sujeevan Leonard Thamakulasingam
Job Title Ref
By Date21-Oct-21 Chd
z-axis y-axis
Moment of inertia : 1491.000 1491.000
Plastic modulus : 237.000 237.000
Elastic modulus : 198.800 198.800
Shear Area : 22.400 22.400
Radius of gyration : 5.769 5.769
Effective Length : 360.000 360.000
z-axis y-axis
Slenderness ratio (KL/r) : 62.4 62.4
Compression Capacity : 1250.0 1250.0
Tension Capacity : 1580.5 1580.5
Moment Capacity : 84.1 84.1
Reduced Moment Capacity : 84.1 84.1
Shear Capacity : 459.1 459.1
Print Time/Date: 07/01/2022 09:37 STAAD.Pro CONNECT Edition 22.08.00.175 Print Run 36 of 87
Job No Sheet No Rev
37
Software licensed to AECOM- CSS Part
CONNECTED User: Sujeevan Leonard Thamakulasingam
Job Title Ref
By Date21-Oct-21 Chd
z-axis y-axis
Moment of inertia : 23910.004 8084.001
Plastic modulus : 1480.000 911.000
Elastic modulus : 1195.500 808.400
Shear Area : 38.333 76.667
Radius of gyration : 14.419 8.384
Effective Length : 370.000 370.000
z-axis y-axis
Slenderness ratio (KL/r) : 25.7 44.1
Compression Capacity : 3725.6 3469.
Print Time/Date: 07/01/2022 09:37 STAAD.Pro CONNECT Edition 22.08.00.175 Print Run 37 of 87
Job No Sheet No Rev
38
Software licensed to AECOM- CSS Part
CONNECTED User: Sujeevan Leonard Thamakulasingam
Job Title Ref
By Date21-Oct-21 Chd
z-axis y-axis
Moment of inertia : 23910.004 8084.001
Plastic modulus : 1480.000 911.000
Elastic modulus : 1195.500 808.40
Print Time/Date: 07/01/2022 09:37 STAAD.Pro CONNECT Edition 22.08.00.175 Print Run 38 of 87
Job No Sheet No Rev
39
Software licensed to AECOM- CSS Part
CONNECTED User: Sujeevan Leonard Thamakulasingam
Job Title Ref
By Date21-Oct-21 Chd
z-axis y-axis
Slenderness ratio (KL/r) : 29.1 50.1
Compression Capacity : 3684.1 3359.6
Tension Capacity : 4057.2 4057.2
Moment Capacity : 417.5 264.4
Reduced Moment Capacity : 417.5 264.4
Shear Capacity : 785.7 1571.4
Print Time/Date: 07/01/2022 09:37 STAAD.Pro CONNECT Edition 22.08.00.175 Print Run 39 of 87
Job No Sheet No Rev
40
Software licensed to AECOM- CSS Part
CONNECTED User: Sujeevan Leonard Thamakulasingam
Job Title Ref
By Date21-Oct-21 Chd
=======================================================================
MATERIAL DATA
Grade of steel = S 355
Modulus of elasticity = 205 kN/mm2
Design Strength (py) = 355 N/mm2
z-axis y-axis
Moment of inertia : 23910.004 8084.001
Plastic modulus : 1480.000 911.000
Elastic modulus : 1195.500 808.400
Shear Area : 38.333 76.667
Radius of gyration : 14.419 8.384
Effective Length : 420.000 420.000
z-axis y-axis
Slenderness ratio (KL/r) : 29.1 50.1
Compression Capacity : 3684.1 3359.6
Tension Capacity : 4057.2 4057.2
Moment Capacity : 417.5 264.4
Reduced Moment Capacity : 417.5 264.4
Shear Capacity : 785.7 1571.4
Print Time/Date: 07/01/2022 09:37 STAAD.Pro CONNECT Edition 22.08.00.175 Print Run 40 of 87
Job No Sheet No Rev
41
Software licensed to AECOM- CSS Part
CONNECTED User: Sujeevan Leonard Thamakulasingam
Job Title Ref
By Date21-Oct-21 Chd
z-axis y-axis
Moment of inertia : 1491.000 1491.000
Plastic modulus : 237.000 237.000
Elastic modulus : 198.800 198.800
Shear Area : 22.400 22.400
Radius of gyration : 5.769 5.769
Effective Length : 300.000 300.000
z-axis y-axis
Slenderness ratio (KL/r) : 52.0 52.0
Compression Capacity : 1362.4 1362.4
Tension Capacity : 1580.5 1580.5
Moment Capacity : 84.1 84.1
Reduced Moment Capacity : 84.1 84.1
Shear Capacity : 459.1 459.1
Print Time/Date: 07/01/2022 09:37 STAAD.Pro CONNECT Edition 22.08.00.175 Print Run 41 of 87
Job No Sheet No Rev
42
Software licensed to AECOM- CSS Part
CONNECTED User: Sujeevan Leonard Thamakulasingam
Job Title Ref
By Date21-Oct-21 Chd
z-axis y-axis
Moment of inertia : 1491.000 1491.000
Plastic modulus : 237.000 237.000
Elastic modulus : 198.800 198.800
Shear Area : 22.400 22.400
Radius of gyration : 5.769 5.769
Effective Length : 360.000 360.000
z-axis y-axis
Slenderness ratio (KL/r) : 62.4 62.4
Compression Capacity : 1250.0 1250.0
Tension Capacity : 1580.5 1580.
Print Time/Date: 07/01/2022 09:37 STAAD.Pro CONNECT Edition 22.08.00.175 Print Run 42 of 87
Job No Sheet No Rev
43
Software licensed to AECOM- CSS Part
CONNECTED User: Sujeevan Leonard Thamakulasingam
Job Title Ref
By Date21-Oct-21 Chd
z-axis y-axis
Moment of inertia : 23910.004 8084.001
Plastic modulus : 1480.000 911.000
Elastic modulus : 1195.500 808.400
Shear Area : 38.333 76.667
Radius of gyration : 14.419 8.384
Effective Length : 420.000 420.000
Print Time/Date: 07/01/2022 09:37 STAAD.Pro CONNECT Edition 22.08.00.175 Print Run 43 of 87
Job No Sheet No Rev
44
Software licensed to AECOM- CSS Part
CONNECTED User: Sujeevan Leonard Thamakulasingam
Job Title Ref
By Date21-Oct-21 Chd
z-axis y-axis
Slenderness ratio (KL/r) : 29.1 50.1
Compression Capacity : 3684.1 3359.6
Tension Capacity : 4057.2 4057.2
Moment Capacity : 417.5 264.4
Reduced Moment Capacity : 417.5 264.4
Shear Capacity : 785.7 1571.4
Print Time/Date: 07/01/2022 09:37 STAAD.Pro CONNECT Edition 22.08.00.175 Print Run 44 of 87
Job No Sheet No Rev
45
Software licensed to AECOM- CSS Part
CONNECTED User: Sujeevan Leonard Thamakulasingam
Job Title Ref
By Date21-Oct-21 Chd
z-axis y-axis
Moment of inertia : 1491.000 1491.000
Plastic modulus : 237.000 237.000
Elastic modulus : 198.800 198.800
Shear Area : 22.400 22.400
Radius of gyration : 5.769 5.769
Effective Length : 420.000 420.000
z-axis y-axis
Slenderness ratio (KL/r) : 72.8 72.8
Compression Capacity : 1110.5 1110.5
Tension Capacity : 1580.5 1580.5
Moment Capacity : 84.1 84.1
Reduced Moment Capacity : 84.1 84.1
Shear Capacity : 459.1 459.1
Print Time/Date: 07/01/2022 09:37 STAAD.Pro CONNECT Edition 22.08.00.175 Print Run 45 of 87
Job No Sheet No Rev
46
Software licensed to AECOM- CSS Part
CONNECTED User: Sujeevan Leonard Thamakulasingam
Job Title Ref
By Date21-Oct-21 Chd
z-axis y-axis
Moment of inertia : 1491.000 1491.000
Plastic modulus : 237.000 237.000
Elastic modulus : 198.800 198.800
Shear Area : 22.400 22.400
Radius of gyration : 5.769 5.769
Effective Length : 420.000 420.000
z-axis y-axis
Slenderness ratio (KL/r) : 72.8 72.8
Compression Capacity : 1110.5 1110.5
Tension Capacity : 1580.5 1580.5
Moment Capacity : 84.1 84.1
Reduced Moment Capacity : 84.1 84.1
Shear Capacity : 459.1 459.1
Print Time/Date: 07/01/2022 09:37 STAAD.Pro CONNECT Edition 22.08.00.175 Print Run 46 of 87
Job No Sheet No Rev
47
Software licensed to AECOM- CSS Part
CONNECTED User: Sujeevan Leonard Thamakulasingam
Job Title Ref
By Date21-Oct-21 Chd
z-axis y-axis
Moment of inertia : 23910.004 8084.001
Plastic modulus : 1480.000 911.000
Elastic modulus : 1195.500 808.400
Shear Area : 38.333 76.667
Radius of gyration : 14.419 8.384
Effective Length : 370.000 370.000
z-axis y-axis
Slenderness ratio (KL/r) : 25.7 44.1
Compression Capacity : 3955.8 3667.2
Tension Capacity : 4057.2 4057.2
Moment Capacity : 417.5 264.4
Reduced Moment Capacity : 417.5 264.4
Shear Capacity : 785.7 1571.4
Print Time/Date: 07/01/2022 09:37 STAAD.Pro CONNECT Edition 22.08.00.175 Print Run 47 of 87
Job No Sheet No Rev
48
Software licensed to AECOM- CSS Part
CONNECTED User: Sujeevan Leonard Thamakulasingam
Job Title Ref
By Date21-Oct-21 Chd
z-axis y-axis
Moment of inertia : 23910.004 8084.001
Plastic modulus : 1480.000 911.000
Elastic modulus : 1195.500 808.400
Shear Area : 38.333 76.667
Radius of gyration : 14.419 8.384
Effective Length : 420.000 420.000
z-axis y-axis
Slenderness ratio (KL/r) : 29.1 50.1
Compression Capacity : 3909.6 3541.9
Tension Capacity : 4057.2 4057.2
Moment Capacity : 417.5 264.4
Reduced Moment Capacity : 417.5 264.4
Shear Capacity : 785.7 1571.4
Print Time/Date: 07/01/2022 09:37 STAAD.Pro CONNECT Edition 22.08.00.175 Print Run 48 of 87
Job No Sheet No Rev
49
Software licensed to AECOM- CSS Part
CONNECTED User: Sujeevan Leonard Thamakulasingam
Job Title Ref
By Date21-Oct-21 Chd
z-axis y-axis
Moment of inertia : 1491.000 1491.000
Plastic modulus : 237.000 237.000
Elastic modulus : 198.800 198.800
Shear Area : 22.400 22.400
Radius of gyration : 5.769 5.769
Effective Length : 450.000 450.000
z-axis y-axis
Slenderness ratio (KL/r) : 78.0 78.0
Compression Capacity : 1035.2 1035.2
Tension Capacity : 1580.5 1580.
Print Time/Date: 07/01/2022 09:37 STAAD.Pro CONNECT Edition 22.08.00.175 Print Run 49 of 87
Job No Sheet No Rev
50
Software licensed to AECOM- CSS Part
CONNECTED User: Sujeevan Leonard Thamakulasingam
Job Title Ref
By Date21-Oct-21 Chd
z-axis y-axis
Moment of inertia : 1491.000 1491.000
Plastic modulus : 237.000 237.000
Elastic modulus : 198.800 198.800
Shear Area : 22.400 22.400
Radius of gyration : 5.769 5.769
Effective Length : 450.000 450.000
Print Time/Date: 07/01/2022 09:37 STAAD.Pro CONNECT Edition 22.08.00.175 Print Run 50 of 87
Job No Sheet No Rev
51
Software licensed to AECOM- CSS Part
CONNECTED User: Sujeevan Leonard Thamakulasingam
Job Title Ref
By Date21-Oct-21 Chd
z-axis y-axis
Slenderness ratio (KL/r) : 78.0 78.0
Compression Capacity : 1035.2 1035.2
Tension Capacity : 1580.5 1580.5
Moment Capacity : 84.1 84.1
Reduced Moment Capacity : 84.1 84.1
Shear Capacity : 459.1 459.1
z-axis y-axis
Moment of inertia : 23910.004 8084.001
Plastic modulus : 1480.000 911.000
Elastic modulus : 1195.500 808.400
Shear Area : 38.333 76.667
Radius of gyration : 14.419 8.384
Effective Length : 280.000 280.000
Print Time/Date: 07/01/2022 09:37 STAAD.Pro CONNECT Edition 22.08.00.175 Print Run 51 of 87
Job No Sheet No Rev
52
Software licensed to AECOM- CSS Part
CONNECTED User: Sujeevan Leonard Thamakulasingam
Job Title Ref
By Date21-Oct-21 Chd
z-axis y-axis
Slenderness ratio (KL/r) : 19.4 33.4
Compression Capacity : 4033.5 3848.7
Tension Capacity : 4057.2 4057.2
Moment Capacity : 417.5 264.4
Reduced Moment Capacity : 417.5 264.4
Shear Capacity : 785.7 1571.4
Print Time/Date: 07/01/2022 09:37 STAAD.Pro CONNECT Edition 22.08.00.175 Print Run 52 of 87
Job No Sheet No Rev
53
Software licensed to AECOM- CSS Part
CONNECTED User: Sujeevan Leonard Thamakulasingam
Job Title Ref
By Date21-Oct-21 Chd
z-axis y-axis
Moment of inertia : 23910.004 8084.001
Plastic modulus : 1480.000 911.000
Elastic modulus : 1195.500 808.400
Shear Area : 38.333 76.667
Radius of gyration : 14.419 8.384
Effective Length : 370.000 370.000
z-axis y-axis
Slenderness ratio (KL/r) : 25.7 44.1
Compression Capacity : 3955.8 3667.2
Tension Capacity : 4057.2 4057.2
Moment Capacity : 417.5 264.4
Reduced Moment Capacity : 417.5 264.4
Shear Capacity : 785.7 1571.4
Print Time/Date: 07/01/2022 09:37 STAAD.Pro CONNECT Edition 22.08.00.175 Print Run 53 of 87
Job No Sheet No Rev
54
Software licensed to AECOM- CSS Part
CONNECTED User: Sujeevan Leonard Thamakulasingam
Job Title Ref
By Date21-Oct-21 Chd
z-axis y-axis
Moment of inertia : 23910.004 8084.001
Plastic modulus : 1480.000 911.000
Elastic modulus : 1195.500 808.400
Shear Area : 38.333 76.667
Radius of gyration : 14.419 8.384
Effective Length : 420.000 420.000
z-axis y-axis
Slenderness ratio (KL/r) : 29.1 50.1
Compression Capacity : 3909.6 3541.9
Tension Capacity : 4057.2 4057.2
Moment Capacity : 417.5 264.4
Reduced Moment Capacity : 417.5 264.4
Shear Capacity : 785.7 1571.4
Print Time/Date: 07/01/2022 09:37 STAAD.Pro CONNECT Edition 22.08.00.175 Print Run 54 of 87
Job No Sheet No Rev
55
Software licensed to AECOM- CSS Part
CONNECTED User: Sujeevan Leonard Thamakulasingam
Job Title Ref
By Date21-Oct-21 Chd
z-axis y-axis
Moment of inertia : 23910.004 8084.001
Plastic modulus : 1480.000 911.000
Elastic modulus : 1195.500 808.400
Shear Area : 38.333 76.667
Radius of gyration : 14.419 8.384
Effective Length : 280.000 280.000
z-axis y-axis
Slenderness ratio (KL/r) : 19.4 33.4
Compression Capacity : 4033.5 3848.7
Tension Capacity : 4057.2 4057.2
Moment Capacity : 417.5 264.4
Reduced Moment Capacity : 417.5 264.4
Shear Capacity : 785.7 1571.
Print Time/Date: 07/01/2022 09:37 STAAD.Pro CONNECT Edition 22.08.00.175 Print Run 55 of 87
Job No Sheet No Rev
56
Software licensed to AECOM- CSS Part
CONNECTED User: Sujeevan Leonard Thamakulasingam
Job Title Ref
By Date21-Oct-21 Chd
z-axis y-axis
Moment of inertia : 1491.000 1491.000
Plastic modulus : 237.000 237.000
Elastic modulus : 198.800 198.800
Shear Area : 22.400 22.400
Radius of gyration : 5.769 5.769
Effective Length : 400.000 400.000
Print Time/Date: 07/01/2022 09:37 STAAD.Pro CONNECT Edition 22.08.00.175 Print Run 56 of 87
Job No Sheet No Rev
57
Software licensed to AECOM- CSS Part
CONNECTED User: Sujeevan Leonard Thamakulasingam
Job Title Ref
By Date21-Oct-21 Chd
z-axis y-axis
Slenderness ratio (KL/r) : 69.3 69.3
Compression Capacity : 1159.3 1159.3
Tension Capacity : 1580.5 1580.5
Moment Capacity : 84.1 84.1
Reduced Moment Capacity : 84.1 84.1
Shear Capacity : 459.1 459.1
z-axis y-axis
Moment of inertia : 1491.000 1491.000
Plastic modulus : 237.000 237.000
Elastic modulus : 198.800 198.80
Print Time/Date: 07/01/2022 09:37 STAAD.Pro CONNECT Edition 22.08.00.175 Print Run 57 of 87
Job No Sheet No Rev
58
Software licensed to AECOM- CSS Part
CONNECTED User: Sujeevan Leonard Thamakulasingam
Job Title Ref
By Date21-Oct-21 Chd
z-axis y-axis
Slenderness ratio (KL/r) : 69.3 69.3
Compression Capacity : 1159.3 1159.3
Tension Capacity : 1580.5 1580.5
Moment Capacity : 84.1 84.1
Reduced Moment Capacity : 84.1 84.1
Shear Capacity : 459.1 459.1
Print Time/Date: 07/01/2022 09:37 STAAD.Pro CONNECT Edition 22.08.00.175 Print Run 58 of 87
Job No Sheet No Rev
59
Software licensed to AECOM- CSS Part
CONNECTED User: Sujeevan Leonard Thamakulasingam
Job Title Ref
By Date21-Oct-21 Chd
z-axis y-axis
Moment of inertia : 23910.004 8084.001
Plastic modulus : 1480.000 911.000
Elastic modulus : 1195.500 808.400
Shear Area : 38.333 76.667
Radius of gyration : 14.419 8.384
Effective Length : 370.000 370.000
z-axis y-axis
Slenderness ratio (KL/r) : 25.7 44.1
Compression Capacity : 3955.8 3667.2
Tension Capacity : 4057.2 4057.2
Moment Capacity : 417.5 264.4
Reduced Moment Capacity : 417.5 264.4
Shear Capacity : 785.7 1571.4
Print Time/Date: 07/01/2022 09:37 STAAD.Pro CONNECT Edition 22.08.00.175 Print Run 59 of 87
Job No Sheet No Rev
60
Software licensed to AECOM- CSS Part
CONNECTED User: Sujeevan Leonard Thamakulasingam
Job Title Ref
By Date21-Oct-21 Chd
z-axis y-axis
Moment of inertia : 23910.004 8084.001
Plastic modulus : 1480.000 911.000
Elastic modulus : 1195.500 808.400
Shear Area : 38.333 76.667
Radius of gyration : 14.419 8.384
Effective Length : 420.000 420.000
z-axis y-axis
Slenderness ratio (KL/r) : 29.1 50.1
Compression Capacity : 3684.1 3359.6
Tension Capacity : 4057.2 4057.2
Moment Capacity : 417.5 264.4
Reduced Moment Capacity : 417.5 264.4
Shear Capacity : 785.7 1571.4
Print Time/Date: 07/01/2022 09:37 STAAD.Pro CONNECT Edition 22.08.00.175 Print Run 60 of 87
Job No Sheet No Rev
61
Software licensed to AECOM- CSS Part
CONNECTED User: Sujeevan Leonard Thamakulasingam
Job Title Ref
By Date21-Oct-21 Chd
z-axis y-axis
Moment of inertia : 23910.004 8084.001
Plastic modulus : 1480.000 911.000
Elastic modulus : 1195.500 808.400
Shear Area : 38.333 76.667
Radius of gyration : 14.419 8.384
Effective Length : 280.000 280.000
z-axis y-axis
Slenderness ratio (KL/r) : 19.4 33.4
Compression Capacity : 3795.7 3629.7
Tension Capacity : 4057.2 4057.2
Moment Capacity : 417.5 264.4
Reduced Moment Capacity : 417.5 264.4
Shear Capacity : 785.7 1571.4
Print Time/Date: 07/01/2022 09:37 STAAD.Pro CONNECT Edition 22.08.00.175 Print Run 61 of 87
Job No Sheet No Rev
62
Software licensed to AECOM- CSS Part
CONNECTED User: Sujeevan Leonard Thamakulasingam
Job Title Ref
By Date21-Oct-21 Chd
z-axis y-axis
Moment of inertia (bend.): 23523.262 7665.905
Shift of centroidal axis : 0.000 0.000
Additional moment (kNm) : 0.000 0.000
z-axis y-axis
Moment of inertia : 1491.000 1491.000
Plastic modulus : 237.000 237.000
Elastic modulus : 198.800 198.800
Shear Area : 22.400 22.400
Radius of gyration : 5.769 5.769
Effective Length : 400.000 400.000
Print Time/Date: 07/01/2022 09:37 STAAD.Pro CONNECT Edition 22.08.00.175 Print Run 62 of 87
Job No Sheet No Rev
63
Software licensed to AECOM- CSS Part
CONNECTED User: Sujeevan Leonard Thamakulasingam
Job Title Ref
By Date21-Oct-21 Chd
z-axis y-axis
Slenderness ratio (KL/r) : 69.3 69.3
Compression Capacity : 1159.3 1159.3
Tension Capacity : 1580.5 1580.5
Moment Capacity : 84.1 84.1
Reduced Moment Capacity : 84.1 84.1
Shear Capacity : 459.1 459.1
z-axis y-axis
Moment of inertia : 1491.000 1491.000
Plastic modulus : 237.000 237.000
Elastic modulus : 198.800 198.800
Shear Area : 22.400 22.40
Print Time/Date: 07/01/2022 09:37 STAAD.Pro CONNECT Edition 22.08.00.175 Print Run 63 of 87
Job No Sheet No Rev
64
Software licensed to AECOM- CSS Part
CONNECTED User: Sujeevan Leonard Thamakulasingam
Job Title Ref
By Date21-Oct-21 Chd
z-axis y-axis
Slenderness ratio (KL/r) : 69.3 69.3
Compression Capacity : 1159.3 1159.3
Tension Capacity : 1580.5 1580.5
Moment Capacity : 84.1 84.1
Reduced Moment Capacity : 84.1 84.1
Shear Capacity : 459.1 459.1
Print Time/Date: 07/01/2022 09:37 STAAD.Pro CONNECT Edition 22.08.00.175 Print Run 64 of 87
Job No Sheet No Rev
65
Software licensed to AECOM- CSS Part
CONNECTED User: Sujeevan Leonard Thamakulasingam
Job Title Ref
By Date21-Oct-21 Chd
z-axis y-axis
Moment of inertia : 14661.998 3801.997
Plastic modulus : 1054.500 574.500
Elastic modulus : 837.828 506.933
Shear Area : 28.800 67.200
Radius of gyration : 12.358 6.293
Effective Length : 740.000 740.000
z-axis y-axis
Slenderness ratio (KL/r) : 59.9 117.6
Compression Capacity : 2742.9 1214.6
Tension Capacity : 3386.9 3386.9
Moment Capacity : 297.4 180.0
Reduced Moment Capacity : 297.4 180.0
Shear Capacity : 590.3 1377.3
Print Time/Date: 07/01/2022 09:37 STAAD.Pro CONNECT Edition 22.08.00.175 Print Run 65 of 87
Job No Sheet No Rev
66
Software licensed to AECOM- CSS Part
CONNECTED User: Sujeevan Leonard Thamakulasingam
Job Title Ref
By Date21-Oct-21 Chd
z-axis y-axis
Moment of inertia : 14661.998 3801.997
Plastic modulus : 1054.500 574.500
Elastic modulus : 837.828 506.933
Shear Area : 28.800 67.200
Radius of gyration : 12.358 6.293
Effective Length : 740.000 740.000
z-axis y-axis
Slenderness ratio (KL/r) : 59.9 117.6
Compression Capacity : 2742.9 1214.6
Tension Capacity : 3386.9 3386.9
Moment Capacity : 297.4 180.0
Reduced Moment Capacity : 297.4 180.0
Shear Capacity : 590.3 1377.3
Print Time/Date: 07/01/2022 09:37 STAAD.Pro CONNECT Edition 22.08.00.175 Print Run 66 of 87
Job No Sheet No Rev
67
Software licensed to AECOM- CSS Part
CONNECTED User: Sujeevan Leonard Thamakulasingam
Job Title Ref
By Date21-Oct-21 Chd
51 ST TUB20020012.0(BRITISH SECTIONS)
PASS EC-6.3.3-662 0.461 7
119.55 C 71.83 48.95 3.25
=======================================================================
MATERIAL DATA
Grade of steel = S 355
Modulus of elasticity = 205 kN/mm2
Design Strength (py) = 355 N/mm2
z-axis y-axis
Moment of inertia : 5171.000 5171.000
Plastic modulus : 621.000 621.000
Elastic modulus : 517.100 517.100
Shear Area : 44.350 44.350
Radius of gyration : 7.635 7.635
Effective Length : 325.000 325.000
z-axis y-axis
Slenderness ratio (KL/r) : 42.6 42.6
Compression Capacity : 2851.4 2851.4
Tension Capacity : 3129.3 3129.3
Moment Capacity : 220.5 220.5
Reduced Moment Capacity : 220.5 220.5
Shear Capacity : 909.0 909.0
Print Time/Date: 07/01/2022 09:37 STAAD.Pro CONNECT Edition 22.08.00.175 Print Run 67 of 87
Job No Sheet No Rev
68
Software licensed to AECOM- CSS Part
CONNECTED User: Sujeevan Leonard Thamakulasingam
Job Title Ref
By Date21-Oct-21 Chd
z-axis y-axis
Moment of inertia : 5171.000 5171.000
Plastic modulus : 621.000 621.000
Elastic modulus : 517.100 517.100
Shear Area : 44.350 44.350
Radius of gyration : 7.635 7.635
Effective Length : 325.000 325.000
z-axis y-axis
Slenderness ratio (KL/r) : 42.6 42.6
Compression Capacity : 2851.4 2851.4
Tension Capacity : 3129.3 3129.3
Moment Capacity : 220.5 220.5
Reduced Moment Capacity : 220.5 220.5
Shear Capacity : 909.0 909.0
Print Time/Date: 07/01/2022 09:37 STAAD.Pro CONNECT Edition 22.08.00.175 Print Run 68 of 87
Job No Sheet No Rev
69
Software licensed to AECOM- CSS Part
CONNECTED User: Sujeevan Leonard Thamakulasingam
Job Title Ref
By Date21-Oct-21 Chd
z-axis y-axis
Moment of inertia : 5171.000 5171.000
Plastic modulus : 621.000 621.000
Elastic modulus : 517.100 517.100
Shear Area : 44.350 44.350
Radius of gyration : 7.635 7.635
Effective Length : 325.000 325.000
z-axis y-axis
Slenderness ratio (KL/r) : 42.6 42.6
Compression Capacity : 2851.4 2851.4
Tension Capacity : 3129.3 3129.3
Moment Capacity : 220.5 220.5
Reduced Moment Capacity : 220.5 220.5
Shear Capacity : 909.0 909.0
Print Time/Date: 07/01/2022 09:37 STAAD.Pro CONNECT Edition 22.08.00.175 Print Run 69 of 87
Job No Sheet No Rev
70
Software licensed to AECOM- CSS Part
CONNECTED User: Sujeevan Leonard Thamakulasingam
Job Title Ref
By Date21-Oct-21 Chd
z-axis y-axis
Moment of inertia : 5171.000 5171.000
Plastic modulus : 621.000 621.000
Elastic modulus : 517.100 517.100
Shear Area : 44.350 44.350
Radius of gyration : 7.635 7.635
Effective Length : 325.000 325.000
z-axis y-axis
Slenderness ratio (KL/r) : 42.6 42.6
Compression Capacity : 2851.4 2851.4
Tension Capacity : 3129.3 3129.
Print Time/Date: 07/01/2022 09:37 STAAD.Pro CONNECT Edition 22.08.00.175 Print Run 70 of 87
Job No Sheet No Rev
71
Software licensed to AECOM- CSS Part
CONNECTED User: Sujeevan Leonard Thamakulasingam
Job Title Ref
By Date21-Oct-21 Chd
z-axis y-axis
Moment of inertia : 14661.998 3801.997
Plastic modulus : 1054.500 574.500
Elastic modulus : 837.828 506.933
Shear Area : 28.800 67.200
Radius of gyration : 12.358 6.293
Effective Length : 30.000 30.000
Print Time/Date: 07/01/2022 09:37 STAAD.Pro CONNECT Edition 22.08.00.175 Print Run 71 of 87
Job No Sheet No Rev
72
Software licensed to AECOM- CSS Part
CONNECTED User: Sujeevan Leonard Thamakulasingam
Job Title Ref
By Date21-Oct-21 Chd
z-axis y-axis
Slenderness ratio (KL/r) : 2.4 4.8
Compression Capacity : 3408.0 3408.0
Tension Capacity : 3386.9 3386.9
Moment Capacity : 297.4 180.0
Reduced Moment Capacity : 297.4 180.0
Shear Capacity : 590.3 1377.3
z-axis y-axis
Moment of inertia : 1491.000 1491.000
Plastic modulus : 237.000 237.000
Elastic modulus : 198.800 198.800
Shear Area : 22.400 22.400
Radius of gyration : 5.769 5.76
Print Time/Date: 07/01/2022 09:37 STAAD.Pro CONNECT Edition 22.08.00.175 Print Run 72 of 87
Job No Sheet No Rev
73
Software licensed to AECOM- CSS Part
CONNECTED User: Sujeevan Leonard Thamakulasingam
Job Title Ref
By Date21-Oct-21 Chd
z-axis y-axis
Slenderness ratio (KL/r) : 69.3 69.3
Compression Capacity : 1159.3 1159.3
Tension Capacity : 1580.5 1580.5
Moment Capacity : 84.1 84.1
Reduced Moment Capacity : 84.1 84.1
Shear Capacity : 459.1 459.1
z-axis y-axis
Moment of inertia : 1491.000 1491.000
Plastic modulus : 237.000 237.00
Print Time/Date: 07/01/2022 09:37 STAAD.Pro CONNECT Edition 22.08.00.175 Print Run 73 of 87
Job No Sheet No Rev
74
Software licensed to AECOM- CSS Part
CONNECTED User: Sujeevan Leonard Thamakulasingam
Job Title Ref
By Date21-Oct-21 Chd
z-axis y-axis
Slenderness ratio (KL/r) : 69.3 69.3
Compression Capacity : 1159.3 1159.3
Tension Capacity : 1580.5 1580.5
Moment Capacity : 84.1 84.1
Reduced Moment Capacity : 84.1 84.1
Shear Capacity : 459.1 459.1
Print Time/Date: 07/01/2022 09:37 STAAD.Pro CONNECT Edition 22.08.00.175 Print Run 74 of 87
Job No Sheet No Rev
75
Software licensed to AECOM- CSS Part
CONNECTED User: Sujeevan Leonard Thamakulasingam
Job Title Ref
By Date21-Oct-21 Chd
z-axis y-axis
Moment of inertia : 1491.000 1491.000
Plastic modulus : 237.000 237.000
Elastic modulus : 198.800 198.800
Shear Area : 22.400 22.400
Radius of gyration : 5.769 5.769
Effective Length : 220.000 220.000
z-axis y-axis
Slenderness ratio (KL/r) : 38.1 38.1
Compression Capacity : 1470.4 1470.4
Tension Capacity : 1580.5 1580.5
Moment Capacity : 84.1 84.1
Reduced Moment Capacity : 84.1 84.1
Shear Capacity : 459.1 459.1
Print Time/Date: 07/01/2022 09:37 STAAD.Pro CONNECT Edition 22.08.00.175 Print Run 75 of 87
Job No Sheet No Rev
76
Software licensed to AECOM- CSS Part
CONNECTED User: Sujeevan Leonard Thamakulasingam
Job Title Ref
By Date21-Oct-21 Chd
z-axis y-axis
Moment of inertia : 1491.000 1491.000
Plastic modulus : 237.000 237.000
Elastic modulus : 198.800 198.800
Shear Area : 22.400 22.400
Radius of gyration : 5.769 5.769
Effective Length : 400.000 400.000
z-axis y-axis
Slenderness ratio (KL/r) : 69.3 69.3
Compression Capacity : 1159.3 1159.3
Tension Capacity : 1580.5 1580.5
Moment Capacity : 84.1 84.1
Reduced Moment Capacity : 84.1 84.1
Shear Capacity : 459.1 459.1
Print Time/Date: 07/01/2022 09:37 STAAD.Pro CONNECT Edition 22.08.00.175 Print Run 76 of 87
Job No Sheet No Rev
77
Software licensed to AECOM- CSS Part
CONNECTED User: Sujeevan Leonard Thamakulasingam
Job Title Ref
By Date21-Oct-21 Chd
65 ST TUB20020012.0(BRITISH SECTIONS)
PASS EC-6.3.3-662 0.156 7
59.15 C -1.23 -29.16 3.25
=======================================================================
MATERIAL DATA
Grade of steel = S 355
Modulus of elasticity = 205 kN/mm2
Design Strength (py) = 355 N/mm2
z-axis y-axis
Moment of inertia : 5171.000 5171.000
Plastic modulus : 621.000 621.000
Elastic modulus : 517.100 517.100
Shear Area : 44.350 44.350
Radius of gyration : 7.635 7.635
Effective Length : 325.000 325.000
z-axis y-axis
Slenderness ratio (KL/r) : 42.6 42.6
Compression Capacity : 2851.4 2851.4
Tension Capacity : 3129.3 3129.3
Moment Capacity : 220.5 220.5
Reduced Moment Capacity : 220.5 220.5
Shear Capacity : 909.0 909.0
Print Time/Date: 07/01/2022 09:37 STAAD.Pro CONNECT Edition 22.08.00.175 Print Run 77 of 87
Job No Sheet No Rev
78
Software licensed to AECOM- CSS Part
CONNECTED User: Sujeevan Leonard Thamakulasingam
Job Title Ref
By Date21-Oct-21 Chd
z-axis y-axis
Moment of inertia : 14661.998 3801.997
Plastic modulus : 1054.500 574.500
Elastic modulus : 837.828 506.933
Shear Area : 28.800 67.200
Radius of gyration : 12.358 6.293
Effective Length : 600.000 600.000
z-axis y-axis
Slenderness ratio (KL/r) : 48.6 95.3
Compression Capacity : 2985.5 1705.7
Tension Capacity : 3386.9 3386.9
Moment Capacity : 297.4 180.0
Reduced Moment Capacity : 297.4 180.0
Shear Capacity : 590.3 1377.3
Print Time/Date: 07/01/2022 09:37 STAAD.Pro CONNECT Edition 22.08.00.175 Print Run 78 of 87
Job No Sheet No Rev
79
Software licensed to AECOM- CSS Part
CONNECTED User: Sujeevan Leonard Thamakulasingam
Job Title Ref
By Date21-Oct-21 Chd
z-axis y-axis
Moment of inertia : 5171.000 5171.000
Plastic modulus : 621.000 621.000
Elastic modulus : 517.100 517.100
Shear Area : 44.350 44.350
Radius of gyration : 7.635 7.635
Effective Length : 325.000 325.000
z-axis y-axis
Slenderness ratio (KL/r) : 42.6 42.6
Compression Capacity : 2851.4 2851.4
Tension Capacity : 3129.3 3129.3
Moment Capacity : 220.5 220.5
Reduced Moment Capacity : 220.5 220.5
Shear Capacity : 909.0 909.0
Print Time/Date: 07/01/2022 09:37 STAAD.Pro CONNECT Edition 22.08.00.175 Print Run 79 of 87
Job No Sheet No Rev
80
Software licensed to AECOM- CSS Part
CONNECTED User: Sujeevan Leonard Thamakulasingam
Job Title Ref
By Date21-Oct-21 Chd
z-axis y-axis
Moment of inertia : 1491.000 1491.000
Plastic modulus : 237.000 237.000
Elastic modulus : 198.800 198.800
Shear Area : 22.400 22.400
Radius of gyration : 5.769 5.769
Effective Length : 228.035 228.035
z-axis y-axis
Slenderness ratio (KL/r) : 39.5 39.5
Compression Capacity : 1461.2 1461.2
Tension Capacity : 1580.5 1580.5
Moment Capacity : 84.1 84.
Print Time/Date: 07/01/2022 09:37 STAAD.Pro CONNECT Edition 22.08.00.175 Print Run 80 of 87
Job No Sheet No Rev
81
Software licensed to AECOM- CSS Part
CONNECTED User: Sujeevan Leonard Thamakulasingam
Job Title Ref
By Date21-Oct-21 Chd
z-axis y-axis
Moment of inertia : 23910.004 8084.001
Plastic modulus : 1480.000 911.000
Elastic modulus : 1195.500 808.400
Shear Area : 38.333 76.667
Radius of gyration : 14.419 8.384
Effective Length : 280.000 280.000
Print Time/Date: 07/01/2022 09:37 STAAD.Pro CONNECT Edition 22.08.00.175 Print Run 81 of 87
Job No Sheet No Rev
82
Software licensed to AECOM- CSS Part
CONNECTED User: Sujeevan Leonard Thamakulasingam
Job Title Ref
By Date21-Oct-21 Chd
z-axis y-axis
Slenderness ratio (KL/r) : 19.4 33.4
Compression Capacity : 3795.7 3629.7
Tension Capacity : 4057.2 4057.2
Moment Capacity : 417.5 264.4
Reduced Moment Capacity : 417.5 264.4
Shear Capacity : 785.7 1571.4
Print Time/Date: 07/01/2022 09:37 STAAD.Pro CONNECT Edition 22.08.00.175 Print Run 82 of 87
Job No Sheet No Rev
83
Software licensed to AECOM- CSS Part
CONNECTED User: Sujeevan Leonard Thamakulasingam
Job Title Ref
By Date21-Oct-21 Chd
z-axis y-axis
Moment of inertia : 1491.000 1491.000
Plastic modulus : 237.000 237.000
Elastic modulus : 198.800 198.800
Shear Area : 22.400 22.400
Radius of gyration : 5.769 5.769
Effective Length : 390.000 390.000
z-axis y-axis
Slenderness ratio (KL/r) : 67.6 67.6
Compression Capacity : 1183.0 1183.0
Tension Capacity : 1580.5 1580.5
Moment Capacity : 84.1 84.1
Reduced Moment Capacity : 84.1 84.1
Shear Capacity : 459.1 459.1
Print Time/Date: 07/01/2022 09:37 STAAD.Pro CONNECT Edition 22.08.00.175 Print Run 83 of 87
Job No Sheet No Rev
84
Software licensed to AECOM- CSS Part
CONNECTED User: Sujeevan Leonard Thamakulasingam
Job Title Ref
By Date21-Oct-21 Chd
z-axis y-axis
Moment of inertia : 5171.000 5171.000
Plastic modulus : 621.000 621.000
Elastic modulus : 517.100 517.100
Shear Area : 44.350 44.350
Radius of gyration : 7.635 7.635
Effective Length : 325.000 325.000
z-axis y-axis
Slenderness ratio (KL/r) : 42.6 42.6
Compression Capacity : 2851.4 2851.4
Tension Capacity : 3129.3 3129.3
Moment Capacity : 220.5 220.5
Reduced Moment Capacity : 220.5 220.5
Shear Capacity : 909.0 909.0
Print Time/Date: 07/01/2022 09:37 STAAD.Pro CONNECT Edition 22.08.00.175 Print Run 84 of 87
Job No Sheet No Rev
85
Software licensed to AECOM- CSS Part
CONNECTED User: Sujeevan Leonard Thamakulasingam
Job Title Ref
By Date21-Oct-21 Chd
z-axis y-axis
Moment of inertia : 14661.998 3801.997
Plastic modulus : 1054.500 574.500
Elastic modulus : 837.828 506.933
Shear Area : 28.800 67.200
Radius of gyration : 12.358 6.293
Effective Length : 390.000 390.000
z-axis y-axis
Slenderness ratio (KL/r) : 31.6 62.0
Compression Capacity : 3235.3 2689.8
Tension Capacity : 3386.9 3386.9
Moment Capacity : 297.4 180.0
Reduced Moment Capacity : 297.4 180.0
Shear Capacity : 590.3 1377.3
Print Time/Date: 07/01/2022 09:37 STAAD.Pro CONNECT Edition 22.08.00.175 Print Run 85 of 87
Job No Sheet No Rev
86
Software licensed to AECOM- CSS Part
CONNECTED User: Sujeevan Leonard Thamakulasingam
Job Title Ref
By Date21-Oct-21 Chd
z-axis y-axis
Moment of inertia : 14661.998 3801.997
Plastic modulus : 1054.500 574.500
Elastic modulus : 837.828 506.933
Shear Area : 28.800 67.200
Radius of gyration : 12.358 6.293
Effective Length : 740.000 740.000
z-axis y-axis
Slenderness ratio (KL/r) : 59.9 117.6
Compression Capacity : 2742.9 1214.6
Tension Capacity : 3386.9 3386.9
Moment Capacity : 297.4 180.0
Reduced Moment Capacity : 297.4 180.0
Shear Capacity : 590.3 1377.3
Print Time/Date: 07/01/2022 09:37 STAAD.Pro CONNECT Edition 22.08.00.175 Print Run 86 of 87
Job No Sheet No Rev
87
Software licensed to AECOM- CSS Part
CONNECTED User: Sujeevan Leonard Thamakulasingam
Job Title Ref
By Date21-Oct-21 Chd
Print Time/Date: 07/01/2022 09:37 STAAD.Pro CONNECT Edition 22.08.00.175 Print Run 87 of 87
CHECKING OF EXISITNG BEAMS
RAPT 6.6.8.0 Project Name: J110 Page 2/14
Licensee: AECOM Singapore Pte Ltd 1/7/2022 9:43:31 AM License No.: 10479063400712WPN11
Frame Description: CB101
Project Name: J110 Beams
Project Number: 60628288 Beam Beam Beam Beam Effective
Frame Description: CB101 Number Depth Width Width Flange
Designer: SLT at Width
Slab
C:\Users\sujeevanleonard.tham\OneDrive - AECOM\Projects\J110\J110\OneDrive_2021-07-01\12. Southern mm mm mm mm
Staircase\Design Files\Str\Beams\Beam-Existing\CB101.rpf 1 510 200 200 200
Output 1 2
Warning:At 983mm, the moment curvature calculations did not converge on the design moment within our set limits after 100 iterations. We have adopted kN
the nearest solution. This normally only occurs at points of very low moment and is not normally a problem so we have continued with the design. 60 52.2
Warning:Incremental Deflection span/deflection ratio in at least one span is less than defined limit. 40
Warning:Total deflection in at least one span is greater than defined limit.
20
0
-20
-40
Bending Moments -60 -52.2
Load Cases
0 6780mm
Column Actions
Col No. 1 Self Extra Dead Live Shear Shear 1 Shear 2
Weight Load Load
Moment Above kNm -0 -0 -0
Moment Below kNm -0 -0 -0 Shear
Reaction kN 8.64 22.03 6.78
Elastic Rotation #.# 5.11e-4 1.3e-3 4.01e-4 1 2
Elastic Axial Shortening mm 0 0 0 kNm
5.3 5.3
0
Col No. 2 Self Extra Dead Live Load 20
Weight Load
Moment Above kNm -0 -0 -0 40
Moment Below kNm -0 -0 -0 60
Reaction kN 8.64 22.03 6.78
80
Elastic Rotation #.# -5.11e-4 -1.3e-3 -4.01e-4 82
Elastic Axial Shortening mm 0 0 0 100
0 6780mm
Gross Stress Top Gross Stress Bottom Cracked Compression Reinforcement Tension
1 2
0.03 Reversal Moment Condition
0
-0.03 MPa1 2MPa
-8 -5.02 -240
-0.06
-6 -180
-0.09 -4 -120
-0.12 -2 -60
-0.15 0 0
0.154
-0.18 2 60
0 6780mm 4 120
6 180
Neutral Axis Depth Initial Final 8 5.37 240
0 6780mm
Service Gross Stress Top Gross Stress Bottom Cracked Compression Reinforcement Tension
Maximum Moment Condition
1 2 Characteristic Service
MPa MPa
-8 -6.53 -240
Maximum Moment Condition
-6 -180
-4 -120 1 2
MPa MPa
-2 -60 -9 -6.53 -240
0 0
-6 -160
2 60
4 120 -3 -80
6 180 0 0
8 240 3 80
10 6.75 300 6 160
0 6780mm
9 240
Gross Stress Top Gross Stress Bottom Cracked Compression Reinforcement Tension 12 6.75 320
0 6780mm
Gross Stress Top Gross Stress Bottom Cracked Compression Reinforcement Tension
RAPT 6.6.8.0 Project Name: J110 Page 11/14 RAPT 6.6.8.0 Project Name: J110 Page 12/14
Licensee: AECOM Singapore Pte Ltd 1/7/2022 9:44:02 AM License No.: 10479063400712WPN11 Licensee: AECOM Singapore Pte Ltd 1/7/2022 9:44:05 AM License No.: 10479063400712WPN11
Frame Description: CB101 Frame Description: CB101
Reversal Moment Condition
Spacing of Sets Minimum Legs Shear Comments
1 2 2 legs 4 legs 6 legs Min legs
MPa MPa
-9 -5.8 -240 T10 T10 T10 T10
mm mm mm mm # A
-6 -160
341.3 341.3 341.3 341.3 2 Minimum Steel
-3 -80
341.3 341.3 341.3 341.3 2 Minimum Steel
0 0
341.3 341.3 341.3 341.3 2 Minimum Steel
3 80
341.3 341.3 341.3 341.3 2 Minimum Steel
6 160
9 240
12 6.21 320
0 6780mm
Punching
Gross Stress Top Gross Stress Bottom Cracked Compression Reinforcement Tension Column Head Critical Section
Column Bh a at u d fcv P/A Asw/s min V* Mv* V*eff Vu Vumax Asv result
No.
Shear Design A #.# mm mm mm mm MPa MPa mm2/mm kN kNm kN kN kN mm2 A
Beam 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Check Not Carried Out!
Span 1 2 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Check Not Carried Out!
Locat V* Mv* Pv Mdec d Ast bv phi Vuc phi Vut phi Vu Phi Vumax phi VuMin phi Vus Theta Asv/s
Span 1
Design Comments:-
- Incremental Span/Deflection ratio less than user defined limit = 285
- Total Deflection greater than user defined limit = -25.4mm Reinforcement Layout
(2-T13)
1 2
mm
0
Detailed Reinforcement
Span 1 -100
Top Reinforcement Bottom Reinforcement -200
(2-T20)
100 0 0 61 200 No Steel Added 300 0 449 200 No Steel Added -500
408 0 0 61 200 No Steel Added 300 0 449 200 No Steel Added 0 6780mm
509 0 0 61 200 No Steel Added 300 0 449 200 No Steel Added
511 0 0 61 200 No Steel Added 300 0 449 200 No Steel Added
747 0 0 61 200 No Steel Added 300 0 449 200 No Steel Added
983 0 0 61 200 No Steel Added 300 0 449 200 No Steel Added
1219 0 0 61 200 No Steel Added 300 0 449 200 No Steel Added
1455 0 0 61 200 No Steel Added 300 0 449 200 No Steel Added
1695 0 0 61 200 No Steel Added 300 0 449 200 No Steel Added
2260 0 0 61 200 No Steel Added 300 0 449 200 No Steel Added
2825 0 0 61 200 No Steel Added 254.7 0 449 200 No Steel Added
3390 0 0 61 200 No Steel Added 232.3 0 449 200 No Steel Added
3955 0 0 61 200 No Steel Added 254.7 0 449 200 No Steel Added
4520 0 0 61 200 No Steel Added 300 0 449 200 No Steel Added
5085 0 0 61 200 No Steel Added 300 0 449 200 No Steel Added
5325 0 0 61 200 No Steel Added 300 0 449 200 No Steel Added
5561 0 0 61 200 No Steel Added 300 0 449 200 No Steel Added
5797 0 0 61 200 No Steel Added 300 0 449 200 No Steel Added
6033 0 0 61 200 No Steel Added 300 0 449 200 No Steel Added
6269 0 0 61 200 No Steel Added 300 0 449 200 No Steel Added
6271 0 0 61 200 No Steel Added 300 0 449 200 No Steel Added
6372 0 0 61 200 No Steel Added 300 0 449 200 No Steel Added
6680 0 0 61 200 No Steel Added 300 0 449 200 No Steel Added
Shear Reinforcement
Spacing of Sets
2 legs 4 legs 6 legs Min legs Minimum Shear
Area T10 T10 T10 T10 Legs Comments
mm2/mm mm mm mm mm # A
0.2 341.3 341.3 341.3 341.3 2 Minimum Steel
0.2 341.3 341.3 341.3 341.3 2 Minimum Steel
0.2 341.3 341.3 341.3 341.3 2 Minimum Steel
0.2 341.3 341.3 341.3 341.3 2 Minimum Steel
0.2 341.3 341.3 341.3 341.3 2 Minimum Steel
0.2 341.3 341.3 341.3 341.3 2 Minimum Steel
0.2 341.3 341.3 341.3 341.3 2 Minimum Steel
0.2 341.3 341.3 341.3 341.3 2 Minimum Steel
0.2 341.3 341.3 341.3 341.3 2 Minimum Steel
0.2 341.3 341.3 341.3 341.3 2 Minimum Steel
0.2 341.3 341.3 341.3 341.3 2 Minimum Steel
0.2 341.3 341.3 341.3 341.3 2 Minimum Steel
0.2 341.3 341.3 341.3 341.3 2 Minimum Steel
0.2 341.3 341.3 341.3 341.3 2 Minimum Steel
0.2 341.3 341.3 341.3 341.3 2 Minimum Steel
RAPT 6.6.8.0 Project Name: J110 Page 2/14
Licensee: AECOM Singapore Pte Ltd 1/7/2022 9:45:18 AM License No.: 10479063400712WPN11
Frame Description: CB102
Project Name: J110 Beams
Project Number: 60628288 Beam Beam Beam Beam Effective
Frame Description: CB102 Number Depth Width Width Flange
Designer: SLT at Width
Slab
C:\Users\sujeevanleonard.tham\OneDrive - AECOM\Projects\J110\J110\OneDrive_2021-07-01\12. Southern mm mm mm mm
Staircase\Design Files\Str\Beams\Beam-Existing\CB102.rpf 1 550 200 200 200
Concrete Tensile Strength for Deflection Calculations- #.## x (Fc)n #.# -1 -400
Maximum Value of Ieff/Igross for Deflection Calculations #.# 0.6
Total Deflection Warning Limit - Maximum Span/Deflection #.# 250
Total Deflection Warning Limit - Maximum Deflection mm 25 0 6800mm
Incremental Deflection Warning Limit - Maximum Span/Deflection #.# 360
Incremental Deflection Warning Limit - Maximum Deflection mm 25
Initial Time for Shrinkage List Full Shrinkage
RAPT 6.6.8.0 Project Name: J110 Page 7/14 RAPT 6.6.8.0 Project Name: J110 Page 8/14
Licensee: AECOM Singapore Pte Ltd 1/7/2022 9:45:36 AM License No.: 10479063400712WPN11 Licensee: AECOM Singapore Pte Ltd 1/7/2022 9:45:39 AM License No.: 10479063400712WPN11
Frame Description: CB102 Frame Description: CB102
Plan view Ultimate Design
Flexure
mm1 2
-100
kNm1 2
-20
-50 6.67 6.67
0
20
0 40
60
50 80
100
100 120
0 6800mm 115
Warnings 0 6800mm
Input
No errors or warnings were found. Moment Moment 1 Moment 2
Output 1 2
Warning:Incremental Deflection span/deflection ratio in at least one span is less than defined limit. kN
80 65.7
60
40
20
0
Bending Moments
-20
Load Cases -40
Column Actions -60
Col No. 1 Self Extra Dead Live -80 -65.7
Weight Load Load 0 6800mm
Moment Above kNm -0 -0 -0
Moment Below kNm -0 -0 -0 Shear Shear 1 Shear 2
Reaction kN 9.35 28.9 8.84
Elastic Rotation #.# 4.43e-4 1.37e-3 4.19e-4
Elastic Axial Shortening mm 0 0 0
Shear
0 6800mm
Load Combinations
Column Actions Moment Moment 1 Moment 2
Col No. 1 Characteristic Characteristic Service Service Ultimate Ultimate Ultimate Ultimate
Service Service (Reversal) Flexure Flexure Shear Shear 1 2
(Reversal) (Reversal) (Reversal) kN
Moment Above kNm 0 0 0 0 0 0 0 0 80 65.7
Moment Below kNm 0 0 0 0 0 0 0 0 60
Reaction kN 47.09 47.09 47.09 47.09 67.69 67.69 52.39 67.69 40
Elastic Rotation #.# 2.23e-3 2.23e-3 2.23e-3 2.23e-3 3.21e-3 3.21e-3 2.48e-3 3.21e-3 20
Elastic Axial Shortening mm 0 0 0 0 0 0 0 0 0
-20
-40
Col No. 2 Characteristic Characteristic Service Service Ultimate Ultimate Ultimate Ultimate -60
Service Service (Reversal) Flexure Flexure Shear Shear -80 -65.7
(Reversal) (Reversal) (Reversal)
Moment Above kNm 0 0 0 0 0 0 0 0 0 6800mm
Moment Below kNm 0 0 0 0 0 0 0 0
Reaction kN 47.09 47.09 47.09 47.09 67.69 67.69 52.39 67.69
Shear Shear 1 Shear 2
Elastic Rotation #.# -2.23e-3 -2.23e-3 -2.23e-3 -2.23e-3 -3.21e-3 -3.21e-3 -2.48e-3 -3.21e-3
Elastic Axial Shortening mm 0 0 0 0 0 0 0 0
RAPT 6.6.8.0 Project Name: J110 Page 9/14 RAPT 6.6.8.0 Project Name: J110 Page 10/14
Licensee: AECOM Singapore Pte Ltd 1/7/2022 9:45:43 AM License No.: 10479063400712WPN11 Licensee: AECOM Singapore Pte Ltd 1/7/2022 9:45:46 AM License No.: 10479063400712WPN11
Frame Description: CB102 Frame Description: CB102
Flexural Design Reversal Moment Condition
Ultimate
1 2
MPa MPa
mm21 2
-8 -5.61 -160
100 -6 -120
0 0
80
-4 -80
60
-2 -40
40
20 0 0
0 2 40
-20 4 80
-40 6 120
-60 8 5.93 160
-80 0 0 6800mm
-100
0 6800mm
Gross Stress Top Gross Stress Bottom Cracked Compression Reinforcement Tension
Reinforcement Top Total Bottom Total Top Ultimate Bottom Ultimate Min Top Min Bot
Permanent
kNm1 2 Maximum Moment Condition
-30
0 MPa1 2MPa
30 -8 -160
-5.72
60 -6 -120
90 -4 -80
120 -2 -40
150 0 0
180 2 40
210 4 80
0 6800mm 6 120
8 5.89 160
Capacity Minimum Ultimate Design Initial Final 0 6800mm
Gross Stress Top Gross Stress Bottom Cracked Compression Reinforcement Tension
1 2
0.04 Reversal Moment Condition
0
-0.04 MPa1 2MPa
-0.08 -8 -160
-4.82
-0.12 -6 -120
-0.16 -4 -80
0.17
-0.2
-2 -40
-0.24
-0.28 0 0
-0.32 2 40
0 6800mm 4 80
6 120
Neutral Axis Depth Initial Final 5.1
8 160
0 6800mm
Service Gross Stress Top Gross Stress Bottom Cracked Compression Reinforcement Tension
Maximum Moment Condition
1 2 Characteristic Service
MPa MPa
-6.66 Maximum Moment Condition
-8 -160
-6 -120
1 2
-4 -80 MPa MPa
-2 -40 -9 -6.66 -180
0 0 -6 -120
2 40
-3 -60
4 80
6 120 0 0
8 6.86 160 3 60
0 6800mm 6 120
9 180
Gross Stress Top Gross Stress Bottom Cracked Compression Reinforcement Tension 12 6.86 240
0 6800mm
Gross Stress Top Gross Stress Bottom Cracked Compression Reinforcement Tension
RAPT 6.6.8.0 Project Name: J110 Page 11/14 RAPT 6.6.8.0 Project Name: J110 Page 12/14
Licensee: AECOM Singapore Pte Ltd 1/7/2022 9:45:49 AM License No.: 10479063400712WPN11 Licensee: AECOM Singapore Pte Ltd 1/7/2022 9:45:53 AM License No.: 10479063400712WPN11
Frame Description: CB102 Frame Description: CB102
Reversal Moment Condition
Spacing of Sets Minimum Legs Shear Comments
1 2 2 legs 4 legs 6 legs Min legs
MPa MPa
-9 -5.61 -180 T10 T10 T10 T10
mm mm mm mm # A
-6 -120
369.4 369.4 369.4 369.4 2 Minimum Steel
-3 -60
369.4 369.4 369.4 369.4 2 Minimum Steel
0 0 369.4 369.4 369.4 369.4 2 Minimum Steel
3 60 369.4 369.4 369.4 369.4 2 Minimum Steel
6 120
9 180
12 5.93 240
0 6800mm
Punching
Gross Stress Top Gross Stress Bottom Cracked Compression Reinforcement Tension Column Head Critical Section
Column Bh a at u d fcv P/A Asw/s min V* Mv* V*eff Vu Vumax Asv result
No.
Shear Design A #.# mm mm mm mm MPa MPa mm2/mm kN kNm kN kN kN mm2 A
Beam 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Check Not Carried Out!
Span 1 2 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Check Not Carried Out!
Locat V* Mv* Pv Mdec d Ast bv phi Vuc phi Vut phi Vu Phi Vumax phi VuMin phi Vus Theta Asv/s
Span 1
Design Comments:-
- Incremental Span/Deflection ratio less than user defined limit = 356 Reinforcement Layout
(2-T20)
1 2
mm
Detailed Reinforcement 0
Span 1
Top Reinforcement Bottom Reinforcement -200
(2-T25)
100 0 0 61 200 No Steel Added 300 0 489 200 No Steel Added
440 0 0 61 200 No Steel Added 300 0 489 200 No Steel Added 0 6800mm
549 0 0 61 200 No Steel Added 300 0 489 200 No Steel Added
551 0 0 61 200 No Steel Added 300 0 489 200 No Steel Added
780 0 0 61 200 No Steel Added 300 0 489 200 No Steel Added
1009 0 0 61 200 No Steel Added 300 0 489 200 No Steel Added
1238 0 0 61 200 No Steel Added 300 0 489 200 No Steel Added
1467 0 0 61 200 No Steel Added 300 0 489 200 No Steel Added
1700 0 0 61 200 No Steel Added 300 0 489 200 No Steel Added
2266 0 0 61 200 No Steel Added 300 0 489 200 No Steel Added
2832 0 0 61 200 No Steel Added 300 0 489 200 No Steel Added
3400 0 0 61 200 No Steel Added 300 0 489 200 No Steel Added
3968 0 0 61 200 No Steel Added 300 0 489 200 No Steel Added
4534 0 0 61 200 No Steel Added 300 0 489 200 No Steel Added
5100 0 0 61 200 No Steel Added 300 0 489 200 No Steel Added
5333 0 0 61 200 No Steel Added 300 0 489 200 No Steel Added
5562 0 0 61 200 No Steel Added 300 0 489 200 No Steel Added
5791 0 0 61 200 No Steel Added 300 0 489 200 No Steel Added
6020 0 0 61 200 No Steel Added 300 0 489 200 No Steel Added
6249 0 0 61 200 No Steel Added 300 0 489 200 No Steel Added
6251 0 0 61 200 No Steel Added 300 0 489 200 No Steel Added
6360 0 0 61 200 No Steel Added 300 0 489 200 No Steel Added
6700 0 0 61 200 No Steel Added 300 0 489 200 No Steel Added
Shear Reinforcement
Spacing of Sets
2 legs 4 legs 6 legs Min legs Minimum Shear
Area T10 T10 T10 T10 Legs Comments
mm2/mm mm mm mm mm # A
0.2 369.4 369.4 369.4 369.4 2 Minimum Steel
0.2 369.4 369.4 369.4 369.4 2 Minimum Steel
0.2 369.4 369.4 369.4 369.4 2 Minimum Steel
0.2 369.4 369.4 369.4 369.4 2 Minimum Steel
0.2 369.4 369.4 369.4 369.4 2 Minimum Steel
0.2 369.4 369.4 369.4 369.4 2 Minimum Steel
0.2 369.4 369.4 369.4 369.4 2 Minimum Steel
0.2 369.4 369.4 369.4 369.4 2 Minimum Steel
0.2 369.4 369.4 369.4 369.4 2 Minimum Steel
0.2 369.4 369.4 369.4 369.4 2 Minimum Steel
0.2 369.4 369.4 369.4 369.4 2 Minimum Steel
0.2 369.4 369.4 369.4 369.4 2 Minimum Steel
0.2 369.4 369.4 369.4 369.4 2 Minimum Steel
0.2 369.4 369.4 369.4 369.4 2 Minimum Steel
0.2 369.4 369.4 369.4 369.4 2 Minimum Steel
0.2 369.4 369.4 369.4 369.4 2 Minimum Steel
RAPT 6.6.8.0 Project Name: J110 Page 2/14
Licensee: AECOM Singapore Pte Ltd 1/7/2022 9:46:51 AM License No.: 10479063400712WPN11
Frame Description: CB105
Project Name: J110 Beams
Project Number: 60628288 Beam Beam Beam Beam Effective
Frame Description: CB105 Number Depth Width Width Flange
Designer: SLT at Width
Slab
C:\Users\sujeevanleonard.tham\OneDrive - AECOM\Projects\J110\J110\OneDrive_2021-07-01\12. Southern mm mm mm mm
Staircase\Design Files\Str\Beams\Beam-Existing\CB105.rpf 1 550 200 200 200
Design Zones
Load Combinations : Construction Layer Steel Left End Distance to Bar stagger Top Right End Distance to Bar stagger Top Cover Maximum Minimum Preferred
Number type Reference left end of length at left Cover at Reference right end of length at right at Right Bar Size Bar Size bar size
Load Description 1. Self 2. Extra 3. Live
Column bar end left end Column bar end end
Combination Weight Dead Load Load List # mm mm mm # mm mm mm List List List
A #.# #.# #.#
1 Bar 1 0 0 45 2 0 0 45 40 20 32
1 Construction 1 0 0
-400
Ultimate Design
Flexure
0 6800mm
kNm1 2
-20
Plan view 6.27 6.27
0
mm1 2 20
-100 40
60
-50 80
100
0 120 108
0 6800mm
50
Moment Moment 1 Moment 2
100
0 6800mm
Warnings 1 2
kN
Input 80 61.8
No errors or warnings were found. 60
40
Output 20
Warning:At 1009mm, the moment curvature calculations did not converge on the design moment within our set limits after 100 iterations. We have adopted 0
the nearest solution. This normally only occurs at points of very low moment and is not normally a problem so we have continued with the design. -20
Warning:Incremental Deflection span/deflection ratio in at least one span is less than defined limit. -40
-60
-80 -61.8
0 6800mm
Flexural Design Gross Stress Top Gross Stress Bottom Cracked Compression Reinforcement Tension
Ultimate Reversal Moment Condition
mm21 2
1 2
100 MPa MPa
0 0
80 -8 -5.76 -240
60 -6 -180
40 -4 -120
20 -2 -60
0 0 0
-20 2 60
-40 4 120
-60 6 180
-80 0 8 240
-100 10 5.76 300
0 6800mm
0 6800mm
Reinforcement Top Total Bottom Total Top Ultimate Bottom Ultimate Min Top Min Bot Gross Stress Top Gross Stress Bottom Cracked Compression Reinforcement Tension
kNm1 2
Permanent
-20
Maximum Moment Condition
0
20 MPa1 2MPa
40 -8 -240
-5.7
60 -6 -180
80 -4 -120
100 -2 -60
120 0 0
2 60
0 6800mm
4 120
Capacity Minimum Ultimate Design Initial Final 6 180
8 5.7 240
0 6800mm
1 2
Gross Stress Top Gross Stress Bottom Cracked Compression Reinforcement Tension
0.03
0
Reversal Moment Condition
-0.03
-0.06 MPa1 2MPa
-0.09 -8 -240
-5
-0.12 -6 -180
0.13
-0.15 -4 -120
-0.18 -2 -60
0 0
0 6800mm
2 60
Neutral Axis Depth Initial Final 4 120
6 180
8 5 240
0 6800mm
Gross Stress Top Gross Stress Bottom Cracked Compression Reinforcement Tension
RAPT 6.6.8.0 Project Name: J110 Page 11/14 RAPT 6.6.8.0 Project Name: J110 Page 12/14
Licensee: AECOM Singapore Pte Ltd 1/7/2022 9:47:22 AM License No.: 10479063400712WPN11 Licensee: AECOM Singapore Pte Ltd 1/7/2022 9:47:25 AM License No.: 10479063400712WPN11
Frame Description: CB105 Frame Description: CB105
Characteristic Service
Maximum Moment Condition Spacing of Sets Minimum Legs Shear Comments
2 legs 4 legs 6 legs Min legs
1 2 T10 T10 T10 T10
MPa MPa mm mm mm mm # A
-9 -6.57 -240
371.3 371.3 371.3 371.3 2 Minimum Steel
-6 -160
371.3 371.3 371.3 371.3 2 Minimum Steel
-3 -80 371.3 371.3 371.3 371.3 2 Minimum Steel
0 0 371.3 371.3 371.3 371.3 2 Minimum Steel
3 80 371.3 371.3 371.3 371.3 2 Minimum Steel
6 160 371.3 371.3 371.3 371.3 2 Minimum Steel
9 240 371.3 371.3 371.3 371.3 2 Minimum Steel
12 6.57 320 371.3 371.3 371.3 371.3 2 Minimum Steel
0 6800mm 371.3 371.3 371.3 371.3 2 Minimum Steel
371.3 371.3 371.3 371.3 2 Minimum Steel
Gross Stress Top Gross Stress Bottom Cracked Compression Reinforcement Tension 371.3 371.3 371.3 371.3 2 Minimum Steel
371.3 371.3 371.3 371.3 2 Minimum Steel
Reversal Moment Condition 371.3 371.3 371.3 371.3 2 Minimum Steel
371.3 371.3 371.3 371.3 2 Minimum Steel
1 2 371.3 371.3 371.3 371.3 2 Minimum Steel
MPa MPa
-9 -5.76 -240 371.3 371.3 371.3 371.3 2 Minimum Steel
-6 -160 371.3 371.3 371.3 371.3 2 Minimum Steel
-3 -80 371.3 371.3 371.3 371.3 2 Minimum Steel
0 0 371.3 371.3 371.3 371.3 2 Minimum Steel
3 80 371.3 371.3 371.3 371.3 2 Minimum Steel
6 160 371.3 371.3 371.3 371.3 2 Minimum Steel
9 240
12 5.76 320
0 6800mm
Punching
Gross Stress Top Gross Stress Bottom Cracked Compression Reinforcement Tension
Column Head Critical Section
Column Bh a at u d fcv P/A Asw/s min V* Mv* V*eff Vu Vumax Asv result
Shear Design No.
A #.# mm mm mm mm MPa MPa mm2/mm kN kNm kN kN kN mm2 A
Beam
1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Check Not Carried Out!
Span 1
2 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Check Not Carried Out!
Locat V* Mv* Pv Mdec d Ast bv phi Vuc phi Vut phi Vu Phi Vumax phi VuMin phi Vus Theta Asv/s
Span 1
Design Comments:-
- Incremental Span/Deflection ratio less than user defined limit = 340 Reinforcement Layout
(2-T20)
1 2
mm
Detailed Reinforcement 0
Span 1
Top Reinforcement Bottom Reinforcement -200
(2-T20)
100 0 0 61 200 No Steel Added 300 0 489 200 No Steel Added
440 0 0 61 200 No Steel Added 300 0 489 200 No Steel Added 0 6800mm
549 0 0 61 200 No Steel Added 300 0 489 200 No Steel Added
551 0 0 61 200 No Steel Added 300 0 489 200 No Steel Added
780 0 0 61 200 No Steel Added 300 0 489 200 No Steel Added
1009 0 0 61 200 No Steel Added 300 0 489 200 No Steel Added
1238 0 0 61 200 No Steel Added 300 0 489 200 No Steel Added
1467 0 0 61 200 No Steel Added 300 0 489 200 No Steel Added
1700 0 0 61 200 No Steel Added 300 0 489 200 No Steel Added
2266 0 0 61 200 No Steel Added 275 0 489 200 No Steel Added
2832 0 0 61 200 No Steel Added 206.9 0 489 200 No Steel Added
3400 0 0 61 200 No Steel Added 189.9 0 489 200 No Steel Added
3968 0 0 61 200 No Steel Added 206.9 0 489 200 No Steel Added
4534 0 0 61 200 No Steel Added 275 0 489 200 No Steel Added
5100 0 0 61 200 No Steel Added 300 0 489 200 No Steel Added
5333 0 0 61 200 No Steel Added 300 0 489 200 No Steel Added
5562 0 0 61 200 No Steel Added 300 0 489 200 No Steel Added
5791 0 0 61 200 No Steel Added 300 0 489 200 No Steel Added
6020 0 0 61 200 No Steel Added 300 0 489 200 No Steel Added
6249 0 0 61 200 No Steel Added 300 0 489 200 No Steel Added
6251 0 0 61 200 No Steel Added 300 0 489 200 No Steel Added
6360 0 0 61 200 No Steel Added 300 0 489 200 No Steel Added
6700 0 0 61 200 No Steel Added 300 0 489 200 No Steel Added
Shear Reinforcement
Spacing of Sets
2 legs 4 legs 6 legs Min legs Minimum Shear
Area T10 T10 T10 T10 Legs Comments
mm2/mm mm mm mm mm # A
0.2 371.3 371.3 371.3 371.3 2 Minimum Steel
0.2 371.3 371.3 371.3 371.3 2 Minimum Steel
RAPT 6.6.8.0 Project Name: J110 Page 2/14
Licensee: AECOM Singapore Pte Ltd 1/7/2022 9:47:54 AM License No.: 10479063400712WPN11
Project Name: J110 Beams
Project Number: 60628288 Beam Beam Beam Beam Effective
Designer: SLT Number Depth Width Width Flange
C:\Users\sujeevanleonard.tham\OneDrive - AECOM\Projects\J110\J110\OneDrive_2021-07-01\12. Southern at Width
Slab
Staircase\Design Files\Str\Beams\Beam-Existing\CB108.rpf mm mm mm mm
1 550 200 200 200
RAPT - Version: 6.6.8.0
Reinforced And Post-Tensioned Concrete Analysis & Design Package
Copyright(C) 1988 - 2021 PCDC Pty. Ltd. All Rights Reserved
Load Cases
Load Load Type Load Definition Live Load Description
Licensee Case Deflection Case
AECOM Singapore Pte Ltd
300 Beach Road List List Y/N A
#03-00 The Concourse 1 Self Weight Applied Loads
Singapore 199555 2 Extra Dead Load Applied Loads
10479063400712WPN11 3 Live Load Applied Loads Y
Span
Span Span Slab Panel Panel Load Combinations : Ultimate
Length Depth Width Width Load Description 1. Self 2. Extra 3.
Left Right Combination Weight Dead Live
mm mm mm mm Load Load
LE 0 A #.# #.# #.#
1 6730 200 200 200 1 Live Load 1.4 1.4 1.6
RE 0 2 Live Load 1 1 1.6
3 Dead Load 1.5 1.5 0
Columns
Column Column Support Transverse Transverse Load Combinations : Short Term Service
Grid Type Column v'c Load Description 1. Self 2. Extra 3. Live
Reference spacing Combination Weight Dead Load Load
A List mm MPa A #.# #.# #.#
1 1 Knife-Edge 200 1 Live Load 1 1 1
2 2 Knife-Edge 200
Reinforcement
Load Combinations : Transfer Prestress Maximum Minimum Minimum Minimum Span Minimum Span Infill Stagger
Load Description 1. Self 2. Extra 3. Live Bar Bar Continuous Reinforcement Reinforcement Bars Bars
Combination Weight Dead Load Load Spacing Spacing Reinforcement into End into Internal
A #.# #.# #.# Support Support
1 Transfer 1 0 0 mm mm #.# #.# #.# Y/N Y/N
Support Reinforcement 300 60 0 N N
Span Reinforcement 300 60 0 0 N N
0 6730mm
Material Properties
Concrete : Standard Concrete : Concrete Strength Basis - Cube
Reinforcement Design Zones User Defined Description A C32/40MPa
Characteristic Compressive Strength MPa 40
1 2 Mean Compressive Strength MPa 46.53
mm Lower Characteristic Tensile Strength MPa 3.16
0 MPa
Upper Characteristic Tensile Strength 5.69
Concrete Density kg/m3 2447
-200 Design Concrete Modulus MPa 28000
Mean Concrete Modulus MPa 29305
Basic Shrinkage Strain mm/mm 0
-400 Shrinkage Multiplier #.# 1
Basic Creep Factor #.# 0
Creep Multiplier #.# 1
0 6730mm Concrete Strain at Peak Stress #.# 0.002
Design Data Squash Load Factor #.# 0.85
Capacity Reduction factor (phi) for Flexure #.# 1 Concrete Strain Limit #.# 0.004
Capacity Reduction factor (phi) for Shear #.# 1 Strength Gain Rate List Normal
Capacity Reduction factor (phi) for Shear with transverse reinf #.# 1 Maximum Aggregate Size mm 20
Material Factor for Concrete in Flexure #.# 1.5
Material Factor for Concrete in Shear #.# 1.25
Material Factor for Reinforcement #.# 1.15 Reinforcement Bar
Maximum Ratio of Neutral Axis Depth for Ductility #.# 0.5 Designation Type Yield Elastic Ductility Peak Peak Design Material Material Material Capacity Material Capacity Include as Description
Ductility Limit - Strain #.# 0 Stress Modulus Strain Stress Strain Factor Factor Reduction Factor Reduction Factor Flexural
Ductility Check at Left End Column Y/N Y Limit Flexure Shear - Flexure - Shear Reinforcement for
Ductility Check at Right End Column Y/N Y Shear
Minimum Reinforcement Strength Limit - #.## x M* #.# 0 T Deformed 460 2.05e5 N 0.05 496.8 90 -1 -1 -1 -1 Y
Flexural Critical Section - Consider Transverse Beams Y/N Y
Flexural Critical Section - Distance from centre of Support #.# -1
Beam Left Sideface Cover (Internal) mm 25 Nominal Bar Bar Area Bar Bar Stock
Beam Right Sideface cover mm 40 Bar Size Diameter Inertia Weight Length
Prestress Minimum Reinforcement Basis List Program Default A mm mm2 mm4 kg/m mm
Shear Enhancement at Supports Y/N Y 10 10 78.5 491.07 0.62 12000
Ast Value in Shear Calculations List Calculated 13 13 132.7 1402.55 1.04 12000
Maximum Shear Stress for BS8110 MPa 0 16 16 201.1 3218.29 1.58 12000
Limit Reinforcement Strain Y/N Y 20 20 314.2 7857.14 2.47 12000
Include Strain Hardening of Reinforcement Y/N N 22 22 380.1 11503.6 2.98 12000
Beam Shear Critical Section Location List Code Critical Section 25 25 490.9 19182.5 3.85 12000
32 32 804.2 51492.6 6.31 12000
40 40 1256.6 1.257e5 9.86 12000
mm1 2
-100
Ultimate Design
Flexure
-50
kNm1 2
0 -40
13.5 13.5
0
50 40
80
100 120
0 6730mm
Warnings 160
200
Input
No errors or warnings were found. 240
231
0 6730mm
Output
Warning:At 440mm, the moment curvature calculations did not converge on the design moment within our set limits after 100 iterations. We have adopted Moment Moment 1 Moment 2
the nearest solution. This normally only occurs at points of very low moment and is not normally a problem so we have continued with the design.
Warning:Incremental Deflection span/deflection ratio in at least one span is less than defined limit.
Warning:Total Deflection span/deflection ratio in at least one span is less than defined limit. 1 2
Warning:Incremental deflection in at least one span is greater than defined limit. kN
Warning:Total deflection in at least one span is greater than defined limit. 160 133
120
80
40
0
-40
Bending Moments -80
Load Cases -120
Column Actions -160 -133
Col No. 1 Self Extra Dead Live 0 6730mm
Weight Load Load
Moment Above kNm -0 -0 -0 Shear Shear 1 Shear 2
Moment Below kNm -0 -0 -0
Reaction kN 9.25 50.48 33.65
Elastic Rotation #.# 4.3e-4 2.34e-3 1.56e-3
Shear
Elastic Axial Shortening mm 0 0 0
kNm1 2
-40
Col No. 2 Self Extra Live Load 13.5 13.5
Weight Dead 0
Load 40
Moment Above kNm -0 -0 -0 80
Moment Below kNm -0 -0 -0 120
Reaction kN 9.25 50.48 33.65 160
Elastic Rotation #.# -4.3e-4 -2.34e-3 -1.56e-3 200 186
Elastic Axial Shortening mm 0 0 0 240
0 6730mm
Flexural Design Gross Stress Top Gross Stress Bottom Cracked Compression Reinforcement Tension
Ultimate Reversal Moment Condition
mm21 2
1 2
3000 MPa MPa
0
200 -16 -10.23 -280
100 -12 -210
0 -8 -140
-100
-200 -4 -70
-300 0 0
-400 4 70
-500
-600 8 140
-700 12 210
-800 679 16 280
11.37
0 6730mm
0 6730mm
Reinforcement Top Total Bottom Total Top Ultimate Bottom Ultimate Min Top Min Bot Gross Stress Top Gross Stress Bottom Cracked Compression Reinforcement Tension
kNm1 2
Permanent
-40
Maximum Moment Condition
0
40
MPa1 2MPa
80 -12 -200
-9.16
120 -9 -150
160 -6 -100
200 -3 -50
240 0 0
3 50
0 6730mm
6 100
Capacity Minimum Ultimate Design Initial Final 9 150
12 9.68 200
0 6730mm
1 2
0.04 Gross Stress Top Gross Stress Bottom Cracked Compression Reinforcement Tension
0
Reversal Moment Condition
-0.04
-0.08 1 2
MPa MPa
-0.12 -12 -7.47 -200
-0.16 -9 -150
-0.2 -6 -100
-3 -50
0.218
-0.24
0 6730mm 0 0
3 50
Neutral Axis Depth Initial Final 6 100
9 150
12 8.3 200
0 6730mm
Gross Stress Top Gross Stress Bottom Cracked Compression Reinforcement Tension
RAPT 6.6.8.0 Project Name: J110 Page 11/14 RAPT 6.6.8.0 Project Name: J110 Page 12/14
Licensee: AECOM Singapore Pte Ltd 1/7/2022 9:48:24 AM License No.: 10479063400712WPN11 Licensee: AECOM Singapore Pte Ltd 1/7/2022 9:48:27 AM License No.: 10479063400712WPN11
Characteristic Service
Maximum Moment Condition Spacing of Sets Minimum Legs Shear Comments
2 legs 4 legs 6 legs Min legs
1 2 T10 T10 T10 T10
MPa MPa mm mm mm mm # A
-15 -12.55 -270 371.3 371.3 371.3 371.3 2 Minimum Steel
-10 -180 371.3 371.3 371.3 371.3 2 Minimum Steel
-5 -90 371.3 371.3 371.3 371.3 2 Minimum Steel
0 0 371.3 371.3 371.3 371.3 2 Minimum Steel
5 90 371.3 371.3 371.3 371.3 2 Minimum Steel
10 180 371.3 371.3 371.3 371.3 2 Minimum Steel
15 270 371.3 371.3 371.3 371.3 2 Minimum Steel
20 13.26 360 371.3 371.3 371.3 371.3 2 Minimum Steel
0 6730mm 371.3 371.3 371.3 371.3 2 Minimum Steel
371.3 371.3 371.3 371.3 2 Minimum Steel
Gross Stress Top Gross Stress Bottom Cracked Compression Reinforcement Tension 371.3 371.3 371.3 371.3 2 Minimum Steel
371.3 371.3 371.3 371.3 2 Minimum Steel
Reversal Moment Condition 371.3 371.3 371.3 371.3 2 Minimum Steel
371.3 371.3 371.3 371.3 2 Minimum Steel
1 2 371.3 371.3 371.3 371.3 2 Minimum Steel
MPa MPa
-15 -10.23 -270 371.3 371.3 371.3 371.3 2 Minimum Steel
371.3 371.3 371.3 371.3 2 Minimum Steel
-10 -180
371.3 371.3 371.3 371.3 2 Minimum Steel
-5 -90
371.3 371.3 371.3 371.3 2 Minimum Steel
0 0
371.3 371.3 371.3 371.3 2 Minimum Steel
5 90
10 180
15 270
20 11.37 360
0 6730mm Punching
Gross Stress Top Gross Stress Bottom Cracked Compression Reinforcement Tension
Column Head Critical Section
Column Bh a at u d fcv P/A Asw/s min V* Mv* V*eff Vu Vumax Asv result
No.
Shear Design A #.# mm mm mm mm MPa MPa mm2/mm kN kNm kN kN kN mm2 A
Beam 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Check Not Carried Out!
2 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Check Not Carried Out!
Span 1
Locat V* Mv* Pv Mdec d Ast bv phi Vuc phi Vut phi Vu Phi Vumax phi VuMin phi Vus Theta Asv/s
-60
Spacing of Sets Minimum Legs Shear Comments
2 legs 4 legs 6 legs Min legs -80
T10 T10 T10 T10
343
mm mm mm mm # A -100
0 6730mm
371.3 371.3 371.3 371.3 2 Minimum Steel
371.3 371.3 371.3 371.3 2 Minimum Steel
371.3 371.3 371.3 371.3 2 Minimum Steel
RAPT 6.6.8.0 Project Name: J110 Page 13/14 RAPT 6.6.8.0 Project Name: J110 Page 14/14
Licensee: AECOM Singapore Pte Ltd 1/7/2022 9:48:30 AM License No.: 10479063400712WPN11 Licensee: AECOM Singapore Pte Ltd 1/7/2022 9:48:34 AM License No.: 10479063400712WPN11
Incremental Shear Reinforcement
Spacing of Sets
mm1 2 2 legs 4 legs 6 legs Min legs Minimum Shear
0 Area T10 T10 T10 T10 Legs Comments
mm2/mm mm mm mm mm # A
-20 0.2 371.3 371.3 371.3 371.3 2 Minimum Steel
0.2 371.3 371.3 371.3 371.3 2 Minimum Steel
-40 -32.4 0.2 371.3 371.3 371.3 371.3 2 Minimum Steel
-60 0.2 371.3 371.3 371.3 371.3 2 Minimum Steel
0.2 371.3 371.3 371.3 371.3 2 Minimum Steel
-80 0.2 371.3 371.3 371.3 371.3 2 Minimum Steel
208 0.2 371.3 371.3 371.3 371.3 2 Minimum Steel
-100 0.2 371.3 371.3 371.3 371.3 2 Minimum Steel
0 6730mm
0.2 371.3 371.3 371.3 371.3 2 Minimum Steel
Total Long Term 0.2 371.3 371.3 371.3 371.3 2 Minimum Steel
0.2 371.3 371.3 371.3 371.3 2 Minimum Steel
mm1 2 0.2 371.3 371.3 371.3 371.3 2 Minimum Steel
0 0.2 371.3 371.3 371.3 371.3 2 Minimum Steel
0.2 371.3 371.3 371.3 371.3 2 Minimum Steel
-20 0.2 371.3 371.3 371.3 371.3 2 Minimum Steel
-40 0.2 371.3 371.3 371.3 371.3 2 Minimum Steel
-33.6
0.2 371.3 371.3 371.3 371.3 2 Minimum Steel
-60 0.2 371.3 371.3 371.3 371.3 2 Minimum Steel
0.2 371.3 371.3 371.3 371.3 2 Minimum Steel
-80 0.2 371.3 371.3 371.3 371.3 2 Minimum Steel
-100 200 0.2 371.3 371.3 371.3 371.3 2 Minimum Steel
0 6730mm 0.2 371.3 371.3 371.3 371.3 2 Minimum Steel
0.2 371.3 371.3 371.3 371.3 2 Minimum Steel
Span 1
Design Comments:- Design Comments:-
- Incremental Span/Deflection ratio less than user defined limit = 208 - - Span 1 - Required Bar Size is smaller than the Preferred Bar Size. Maintaining the same cover will require slightly less reinforcement than calculated.
- Total Span/Deflection ratio less than user defined limit = 200
- Incremental Deflection greater than user defined limit = -32.4mm
- Total Deflection greater than user defined limit = -33.6mm
Reinforcement Layout
(2-T20)
1 2
Detailed Reinforcement mm
Span 1 0
Top Reinforcement Bottom Reinforcement
-200
Max Section Max Section
Locat Space Area Depth Width Rebar Reqd Space Area Depth Width Rebar Reqd
mm mm mm2 mm mm A mm mm2 mm mm A -400
100 0 0 61 200 No Steel Added 300 0 489 200 No Steel Added
2-T25
(2-T20)
440 0 0 61 200 No Steel Added 300 0 489 200 No Steel Added
549 0 0 61 200 No Steel Added 300 34.89 489 200 1 T25 @ 999 0 6730mm
551 0 0 61 200 No Steel Added 300 35.93 489 200 1 T25 @ 999
777 0 0 61 200 No Steel Added 300 148.02 489 200 1 T25 @ 999
1003 0 0 61 200 No Steel Added 166.6 251.47 489 200 1 T25 @ 999 - - Span 1 - Required Bar Size is smaller than the Preferred Bar Size. Maintaining the same cover will require slightly less reinforcement than calculated.
1229 0 0 61 200 No Steel Added 153.9 348.25 489 200 1 T25 @ 999
1455 0 0 61 200 No Steel Added 150 433.44 489 200 1 T25 @ 999
1682.5 0 0 61 200 No Steel Added 143.4 514.03 489 200 2 T25 @ 90
2242.5 0 0 61 200 No Steel Added 133.9 645.56 489 200 2 T25 @ 90
2802.5 0 0 61 200 No Steel Added 130.8 676.52 489 200 2 T25 @ 90
3365 0 0 61 200 No Steel Added 128.2 678.83 489 200 2 T25 @ 90
3927.5 0 0 61 200 No Steel Added 130.8 676.52 489 200 2 T25 @ 90
4487.5 0 0 61 200 No Steel Added 133.9 645.56 489 200 2 T25 @ 90
5047.5 0 0 61 200 No Steel Added 143.4 514.03 489 200 2 T25 @ 90
5275 0 0 61 200 No Steel Added 150 433.44 489 200 1 T25 @ 999
5501 0 0 61 200 No Steel Added 153.9 348.25 489 200 1 T25 @ 999
5727 0 0 61 200 No Steel Added 166.6 251.47 489 200 1 T25 @ 999
5953 0 0 61 200 No Steel Added 300 148.02 489 200 1 T25 @ 999
6179 0 0 61 200 No Steel Added 300 35.93 489 200 1 T25 @ 999
6181 0 0 61 200 No Steel Added 300 34.89 489 200 1 T25 @ 999
6290 0 0 61 200 No Steel Added 300 0 489 200 No Steel Added
6630 0 0 61 200 No Steel Added 300 0 489 200 No Steel Added
RAPT 6.6.8.0 Project Name: J110 Page 2/26
Licensee: AECOM Singapore Pte Ltd 1/7/2022 10:15:45 AM License No.: 10479063400712WPN11
Project Name: J110 Column Transverse Transverse
Project Number: 60628288 effective depth v'c
difference
Designer: SLT mm MPa
C:\Users\sujeevanleonard.tham\OneDrive - AECOM\Projects\J110\J110\OneDrive_2021-07-01\12. Southern 1
Staircase\Design Files\Str\Beams\Beam-Existing\CB111 TO CB114a(For 200mm topping proposal).rpf 2
3
RAPT - Version: 6.6.8.0 4
Reinforced And Post-Tensioned Concrete Analysis & Design Package 5
Copyright(C) 1988 - 2021 PCDC Pty. Ltd. All Rights Reserved
Licensee Beams
AECOM Singapore Pte Ltd Beam Beam Beam Beam Effective
300 Beach Road Number Depth Width Width Flange
#03-00 The Concourse at Width
Singapore 199555 Slab
10479063400712WPN11 mm mm mm mm
1 700 300 300 300
2 700 300 300 300
3 700 300 300 300
4 700 300 300 300
Input
General Load Cases
Design Code List Singapore - CP 65*SAVED*
Load Load Type Load Definition Live Load Description
Material List Singapore - Singapore BS8110 Materials*SAVED* Case Deflection Case
Reinforcement Type List Reinforced
Member Type List Beam List List Y/N A
Panel Type List Internal 1 Self Weight Applied Loads
Strip Type List One way - Nominal Width 2 Extra Dead Load Applied Loads
Column Stiffness List Equivalent Column 3 Live Load Applied Loads Y
Concrete Type List Standard Concrete
Concrete - Spanning Members List C32/40MPa
Concrete - Columns List C32/40MPa
1. Self Weight - Line
Top Reinforcement Cover mm 45 Load Left End Left end of Load Right Right end of Load Description
Bottom Reinforcement Cover mm 45 Reference load from at left End load from at right
Top Reinforcement Axis Depth Limit mm 30 Column reference end reference reference end
Bottom Reinforcement Axis Depth Limit mm 30 column column column
Concrete Unit Weight kn/m3 25 # mm kN/m # mm kN/m A
Self Weight Definition List Program Calculated 1 1 0 4.75 5 0 4.75
Pattern Live Load Y/N Y 2 2 0 6 3 0 6 150mm thk Bondeck, 1.6m width
Earthquake Design List None 3 1 0 15 2 0 15
Moment Redistribution % 0
Design Surface Levels List Extreme Surfaces
1. Self Weight - Point
Load Reference Distance to Load Load Description
Span column Load from Length
Span Span Slab Panel Panel reference
Length Depth Width Width column
Left Right # mm kN mm A
mm mm mm mm 1 2 3500 90 0 CB152
LE 0 2 3 2800 72 0 CB155
1 8000 200 200 200 3 4 2800 40 0 CB152(4M)
2 7000 200 200 200 4 4 5600 35 0 CB167(4M)
3 5600 200 200 200 5 3 2400 30 0 COM BEAM
4 6400 200 200 200 6 3 4000 25 0 COM BEAM
RE 0
-200
Layer Minimum Maximum Minimum % in
Number Number of Spacing of Steel area as Flange -400
Bars Bars %
# mm % % -600
1 0 0 0 0
-800
0 8000 15000 20600 27000mm
User Defined Reinforcement Design Zones User Defined
Layer Steel type Left End Distance Bar Top % Development % Development Right End Distance Bar Top % Development
Number Reference to left stagger Cover of Left End of of Left End of Bar Reference to right stagger Cover of Right End of 1 2 3 4 5
Column end of length at at left Bar in Tension in Compression Column end of length at at Right Bar in Tension
bar left end end bar right end end mm
List # mm mm mm % % # mm mm mm % 0
1 T 460MPa 1 0 0 35 100 0 2 -2990 0 35 100
-200
2 T 460MPa 1 5000 0 35 100 0 2 2550 0 35 100
3 T 460MPa 1 5000 0 100 0 0 2 2500 0 100 0 -400
4 T 460MPa 2 2500 0 35 100 0 3 -2400 0 35 100
5 T 460MPa 2 4500 0 35 100 0 3 1350 0 35 100 -600
6 T 460MPa 2 5400 0 100 0 0 3 1350 0 100 0 -800
7 T 460MPa 3 1300 0 35 100 0 4 2510 0 35 100
8 T 460MPa 3 1300 0 100 0 0 4 1600 0 100 0 0 8000 15000 20600 27000mm
9 T 460MPa 4 1800 0 35 100 0 5 0 0 35 100 Design Data
10 T 460MPa 4 3600 0 100 0 0 5 0 0 100 0 Capacity Reduction factor (phi) for Flexure #.# 1
Capacity Reduction factor (phi) for Shear #.# 1
Capacity Reduction factor (phi) for Shear with transverse reinf #.# 1
Material Factor for Concrete in Flexure #.# 1.5
Material Factor for Concrete in Shear #.# 1.25
Material Factor for Reinforcement #.# 1.15
Maximum Ratio of Neutral Axis Depth for Ductility #.# 0.5
RAPT 6.6.8.0 Project Name: J110 Page 7/26 RAPT 6.6.8.0 Project Name: J110 Page 8/26
Licensee: AECOM Singapore Pte Ltd 1/7/2022 10:16:03 AM License No.: 10479063400712WPN11 Licensee: AECOM Singapore Pte Ltd 1/7/2022 10:16:07 AM License No.: 10479063400712WPN11
Reinforcement Bar
Ductility Limit - Strain #.# 0 Designation Type Yield Elastic Ductility Peak Peak Design Material Material Material Capacity Material Capacity Include as Description
Ductility Check at Left End Column Y/N Y Stress Modulus Strain Stress Strain Factor Factor Reduction Factor Reduction Factor Flexural
Ductility Check at Right End Column Y/N Y Limit Flexure Shear - Flexure - Shear Reinforcement for
Minimum Reinforcement Strength Limit - #.## x M* #.# 0 Shear
T Deformed 460 2.05e5 N 0.05 496.8 90 -1 -1 -1 -1 Y
Flexural Critical Section - Consider Transverse Beams Y/N Y
Flexural Critical Section - Distance from centre of Support #.# -1
Beam Left Sideface Cover (Internal) mm 25
Beam Right Sideface cover mm 40 Nominal Bar Bar Area Bar Bar Stock
Prestress Minimum Reinforcement Basis List Program Default Bar Size Diameter Inertia Weight Length
A mm mm2 mm4 kg/m mm
Shear Enhancement at Supports Y/N Y
List 10 10 78.5 491.07 0.62 12000
Ast Value in Shear Calculations Calculated
MPa 13 13 132.7 1402.55 1.04 12000
Maximum Shear Stress for BS8110 0
Y/N 16 16 201.1 3218.29 1.58 12000
Limit Reinforcement Strain Y
Y/N 20 20 314.2 7857.14 2.47 12000
Include Strain Hardening of Reinforcement N
List Code Critical Section 22 22 380.1 11503.6 2.98 12000
Beam Shear Critical Section Location
25 25 490.9 19182.5 3.85 12000
32 32 804.2 51492.6 6.31 12000
40 40 1256.6 1.257e5 9.86 12000
Maximum Service Stress Change - Prestressed Sections MPa 200
Maximum Service Stress Change - Reinforced Sections MPa 0
Relative Humidity % 50
Elevation view
Average Temperature C. 20
1 2 3 4 5
Prestress Losses Calculations based on List Program Default
Crack Width Calculations List Code default mm
AS3600 Shrinkage and Temperature Reinforcement List Moderate 0
Degree of Restraint in Primary Direction % 0 -200
Degree of Restraint in Secondary Direction % 0
Concrete Strength Gain Rate List N -400
-600
Concrete Tensile Strength for Deflection Calculations- #.## x (Fc)n #.# -1
Maximum Value of Ieff/Igross for Deflection Calculations #.# 0.6 -800
Total Deflection Warning Limit - Maximum Span/Deflection #.# 250 0 8000 15000 20600 27000mm
Total Deflection Warning Limit - Maximum Deflection mm 25
Incremental Deflection Warning Limit - Maximum Span/Deflection #.# 360 Plan view
Incremental Deflection Warning Limit - Maximum Deflection mm 25
Initial Time for Shrinkage List Full Shrinkage
mm1 2 3 4 5
Time of Loading in days #.# 10 -140
Age Adjustment Factor #.# 0.76
Concrete Strength at Time of Loading MPa 33.8 -70
Loaded Period in years #.# 30
Tension stiffening Approach List Modified Concrete Tensile Modulus Method 0
1 2 3 4 5
kN
Load Combinations 400 316 286
300190
Column Actions 200
169
Col No. 1 Characteristic Characteristic Service Service Ultimate Ultimate Ultimate Ultimate 100
Service Service (Reversal) Flexure Flexure Shear Shear
0
(Reversal) (Reversal) (Reversal)
-100
Moment Above kNm 0 0 0 0 0 0 0 0
-200
Moment Below kNm 0 0 0 0 0 0 0 0 -171
-300
Reaction kN 123.99 123.99 123.99 123.99 182.45 182.45 65.66 196.49 -290 -301 -268
-400
Elastic Rotation #.# 2.14e-3 2.14e-3 2.14e-3 2.14e-3 3.15e-3 3.15e-3 6.43e-4 3.85e-3 0 8000 15000 20600 27000mm
Elastic Axial Shortening mm 0 0 0 0 0 0 0 0
Shear Shear 1 Shear 2
Col No. 2 Characteristic Characteristic Service Service Ultimate Ultimate Ultimate Ultimate
Service Service (Reversal) Flexure Flexure Shear Shear
(Reversal) (Reversal) (Reversal)
Moment Above kNm 0 0 0 0 0 0 0 0
Moment Below kNm -14.94 23.13 -14.94 23.13 -42.24 51.2 -27.01 3.79
Reaction kN 360.22 360.37 360.22 360.37 453.19 467.28 402 629.89
Elastic Rotation #.# -4.71e-4 7.29e-4 -4.71e-4 7.29e-4 -1.33e-3 1.61e-3 -8.52e-4 1.2e-4
Elastic Axial Shortening mm -0.3 -0.3 -0.3 -0.3 -0.4 -0.4 -0.3 -0.5
Col No. 3 Characteristic Characteristic Service Service Ultimate Ultimate Ultimate Ultimate
Service Service (Reversal) Flexure Flexure Shear Shear
(Reversal) (Reversal) (Reversal)
Moment Above kNm 0 0 0 0 0 0 0 0
Moment Below kNm -24.96 7.23 -24.96 7.23 -51.01 29.45 16.68 -13.05
RAPT 6.6.8.0 Project Name: J110 Page 11/26 RAPT 6.6.8.0 Project Name: J110 Page 12/26
Licensee: AECOM Singapore Pte Ltd 1/7/2022 10:16:18 AM License No.: 10479063400712WPN11 Licensee: AECOM Singapore Pte Ltd 1/7/2022 10:16:21 AM License No.: 10479063400712WPN11
Shear
1 2 3 4 5
0.261
0.261
0.131
0.131
0.131
0.131
1 2 3 4 5 0.4
kNm
-600 0.2
-429 -430 -399 -388
-400 -259 -273 0
-200 -0.2
19.3 17.1
0.183
0.187
0 -0.4
200
0.488
0.488
204 149 -0.6
400 314 -0.8
600 442 0 8000 15000 20600 27000mm
0 8000 15000 20600 27000mm
Neutral Axis Depth Initial Final
Moment Moment 1 Moment 2
Service
1 2 3 4 5 Maximum Moment Condition
kN
400 327 298 1 2 3 4 5
300190 MPa MPa
171 -9.22 -10.68 -9.51 -6.77
200 -12 -180
100 -8 -120
0
-4 -60
-100
-200 0 0
-171 4 60
-300
-400 -292 -319 -289 8 120
0 8000 15000 20600 27000mm 12 180
16 8.47 13.44 8.97 5.9 240
FlexuralShear
Design
Shear 1 Shear 2 0 8000 15000 20600 27000mm
Ultimate
Gross Stress Top Gross Stress Bottom Cracked Compression Reinforcement Tension
mm21 2 3 4 5
100 Reversal Moment Condition
0 0 0 0 0
80
60 1 2 3 4 5
40 MPa MPa
-5.23 -5.83 -5.73 -3.97
20 -12 -180
0 -8 -120
-20 -4 -60
-40
-60 0 0
-80 4 60
0 0 0 0
-100 8 120
0 8000 15000 20600 27000mm
12 180
Reinforcement Top Total Bottom Total Top Ultimate Bottom Ultimate Min Top Min Bot 16 5.03 5.93 5.06 3.5 240
0 8000 15000 20600 27000mm
1 2 3 4 5 Gross Stress Top Gross Stress Bottom Cracked Compression Reinforcement Tension
kNm
-1200
-900 Permanent
-600 Maximum Moment Condition
-300
0 1 2 3 4 5
300 MPa MPa
-6.99 -7.93 -7.33 -5.3
600 -9 -120
900 -6 -80
1200 -3 -40
0 8000 15000 20600 27000mm
0 0
Capacity Minimum Ultimate Design Initial Final 3 40
6 80
9 120
12 6.42 9.97 6.4 4.62 160
0 8000 15000 20600 27000mm
Gross Stress Top Gross Stress Bottom Cracked Compression Reinforcement Tension
RAPT 6.6.8.0 Project Name: J110 Page 13/26 RAPT 6.6.8.0 Project Name: J110 Page 14/26
Licensee: AECOM Singapore Pte Ltd 1/7/2022 10:16:25 AM License No.: 10479063400712WPN11 Licensee: AECOM Singapore Pte Ltd 1/7/2022 10:16:29 AM License No.: 10479063400712WPN11
Reversal Moment Condition
Locat V* Mv* Pv Mdec d Ast bv phi Vuc phi Vut phi Vu Phi Vumax phi VuMin phi Vus Theta Asv/s
1 2 3 4 5
MPa MPa
-4.52 -5.34 -5.2 -3.74
-9 -120 mm kN kNm kN kNm mm mm2 mm kN kN kN kN kN kN #.# mm2/mm
-6 -80 5001 -131.7 104.05 0 0 625.7 0 200 119.29 99999 119.29 625.69 183.46 0 45 0.2
-3 -40 5009 -132 103 0 0 625.7 0 200 119.29 99999 119.29 625.69 183.46 0 45 0.2
0 0 5011 -132.08 102.73 0 0 625.7 0 200 119.29 99999 119.29 625.69 183.46 0 45 0.2
3 40 5699 -169.68 23.57 0 0 625.7 0 200 119.29 99999 119.29 625.69 183.46 36.28 45 0.2
6 80 5701 -169.81 23.23 0 0 625.7 0 200 119.29 99999 119.29 625.69 183.46 36.4 45 0.2
9 120 6000 -188.05 -30.27 0 0 630.1 0 200 115.8 99999 115.8 630.06 180.14 58.31 45 0.22
12 4.35 6.74 4.59 3.3 160 6299 -203.92 -74.34 0 0 622.1 0 200 118.78 99999 118.78 622.09 182.41 71.28 45 0.27
0 8000 15000 20600 27000mm 6596 -222.04 -137.6 0 0 616.5 0 200 126.05 99999 126.05 616.5 189.77 81.59 45 0.31
6893 -240.16 -206.23 0 0 616.5 0 200 169.74 99999 169.74 616.5 238.44 51.03 45 0.2
Gross Stress Top Gross Stress Bottom Cracked Compression Reinforcement Tension 7190 -257.6 -275.44 0 0 616.5 0 200 259.76 99999 259.76 616.5 338.74 0 45 0.2
7470 -274.68 -349.96 0 0 616.5 0 200 519.51 99999 519.51 616.5 628.17 0 45 0.2
Characteristic Service 7750 -291.76 -429.26 0 0 616.5 0 200 1.18e5 99999 99999 616.5 1e5 0 45 0.2
Maximum Moment Condition
Spacing of Sets Minimum Legs Shear Comments
1 2 3 4 5 2 legs 4 legs 6 legs Min legs
MPa MPa T10 T10 T10 T10
-9.22 -10.68 -9.51 -6.77 mm mm mm mm # A
-12 -180
-8 -120 486.8 486.8 486.8 486.8 2 Minimum Steel
-4 -60 486.8 486.8 486.8 486.8 2 Minimum Steel
0 0 486.8 486.8 486.8 486.8 2 Minimum Steel
4 60 486.8 486.8 486.8 486.8 2 Minimum Steel
8 120 486.8 486.8 486.8 486.8 2 Minimum Steel
12 180 486.8 486.8 486.8 486.8 2 Minimum Steel
16 240 486.8 486.8 486.8 486.8 2 Minimum Steel
20 8.47 13.44 8.97 5.9 300 486.8 486.8 486.8 486.8 2 Minimum Steel
0 8000 15000 20600 27000mm
486.8 486.8 486.8 486.8 2 Minimum Steel
Gross Stress Top Gross Stress Bottom Cracked Compression Reinforcement Tension 486.8 486.8 486.8 486.8 2 Minimum Steel
486.8 486.8 486.8 486.8 2 Minimum Steel
Reversal Moment Condition 486.8 486.8 486.8 486.8 2 Minimum Steel
486.8 486.8 486.8 486.8 2 Minimum Steel
1 2 3 4 5 486.8 486.8 486.8 486.8 2 Minimum Steel
MPa MPa 486.8 486.8 486.8 486.8 2 Minimum Steel
-5.23 -5.83 -5.73 -3.97
-12 -180 486.8 486.8 486.8 486.8 2 Minimum Steel
-8 -120 486.8 486.8 486.8 486.8 2 Minimum Steel
-4 -60 486.8 486.8 486.8 486.8 2 Minimum Steel
0 0 486.8 486.8 486.8 486.8 2 Minimum Steel
4 60
486.8 486.8 486.8 486.8 2 Minimum Steel
8 120
486.8 486.8 486.8 486.8 2
12 180
486.8 486.8 486.8 486.8 2
16 240
20 5.03 5.93 5.06 3.5 300 486.8 486.8 486.8 486.8 2
0 8000 15000 20600 27000mm 486.8 486.8 486.8 486.8 2
486.8 486.8 486.8 486.8 2 Minimum Steel
Gross Stress Top Gross Stress Bottom Cracked Compression Reinforcement Tension 486.8 486.8 486.8 486.8 2 Minimum Steel
486.8 486.8 486.8 486.8 2 Minimum Steel
Shear Design
Beam
Span 1 Span 2
Locat V* Mv* Pv Mdec d Ast bv phi Vuc phi Vut phi Vu Phi Vumax phi VuMin phi Vus Theta Asv/s Locat V* Mv* Pv Mdec d Ast bv phi Vuc phi Vut phi Vu Phi Vumax phi VuMin phi Vus Theta Asv/s
mm kN kNm kN kNm mm mm2 mm kN kN kN kN kN kN #.# mm2/mm mm kN kNm kN kNm mm mm2 mm kN kN kN kN kN kN #.# mm2/mm
100 190.39 19.34 0 0 649 0 200 1356.74 99999 1356.74 649 1583.16 0 45 0.2 250 327.26 -429.83 0 0 616.5 0 200 1.18e5 99999 99999 616.5 1e5 0 45 0.2
560 162.33 100.47 0 0 649 0 200 242.28 99999 242.28 649 325.36 0 45 0.2 530 317.89 -339.51 0 0 616.5 0 200 519.51 99999 519.51 616.5 628.17 0 45 0.2
699 153.85 122.44 0 0 649 0 200 194.1 99999 194.1 649 270.98 0 45 0.2 810 308.52 -251.81 0 0 616.5 0 200 259.76 99999 259.76 616.5 338.74 19.1 45 0.2
701 153.73 122.75 0 0 649 0 200 193.54 99999 193.54 649 270.36 0 45 0.2 1045 301.22 -182.54 0 0 618.9 0 200 184.24 99999 184.24 618.93 255 95.73 45 0.37
960 137.93 160.52 0 0 635.3 0 200 149.16 99999 149.16 635.26 218.27 0 45 0.2 1280 293.35 -112.68 0 0 623.9 0 200 144.21 99999 144.21 623.91 211.08 132.19 45 0.51
1219 122.13 194.2 0 0 628.8 0 200 121.5 99999 121.5 628.84 186.36 0 45 0.2 1515 285.49 -44.67 0 0 630.6 0 200 115.43 99999 115.43 630.55 179.79 156.15 45 0.6
1478 106.33 223.78 0 0 625.7 0 200 119.29 99999 119.29 625.69 183.46 0 45 0.2 1750 279.44 14.97 0 0 625.7 0 200 119.29 99999 119.29 625.69 183.46 146.03 45 0.56
1737 90.53 249.27 0 0 625.7 0 200 119.29 99999 119.29 625.69 183.46 0 45 0.2 1799 277.8 28.62 0 0 625.7 0 200 119.29 99999 119.29 625.69 183.46 144.39 45 0.56
2000 76.79 229.18 0 0 625.7 0 200 119.29 99999 119.29 625.69 183.46 0 45 0.2 1801 277.73 29.18 0 0 625.7 0 200 119.29 99999 119.29 625.69 183.46 144.32 45 0.56
2666 37.73 234.91 0 0 625.7 0 200 119.29 99999 119.29 625.69 183.46 0 45 0.2 1849 276.13 42.47 0 0 625.7 0 200 119.29 99999 119.29 625.69 183.46 142.72 45 0.55
3332 -40.03 180.85 0 0 625.7 0 200 119.29 99999 119.29 625.69 183.46 0 45 0.2 1851 276.06 43.02 0 0 625.7 0 200 119.29 99999 119.29 625.69 183.46 142.65 45 0.55
4000 -78.01 175.95 0 0 625.7 0 200 119.29 99999 119.29 625.69 183.46 0 45 0.2 2499 256.08 205.11 0 0 625.7 0 200 119.29 99999 119.29 625.69 183.46 122.67 45 0.47
4309 -89.69 150.04 0 0 625.7 0 200 119.29 99999 119.29 625.69 183.46 0 45 0.2 2501 256.04 205.62 0 0 625.7 0 200 119.29 99999 119.29 625.69 183.46 122.63 45 0.47
4311 -89.77 149.86 0 0 625.7 0 200 119.29 99999 119.29 625.69 183.46 0 45 0.2 2549 255.05 217.89 0 0 625.7 0 200 119.29 99999 119.29 625.69 183.46 121.64 45 0.47
4999 -131.6 104.31 0 0 625.7 0 200 119.29 99999 119.29 625.69 183.46 0 45 0.2 2551 255.01 218.4 0 0 625.7 0 200 119.29 99999 119.29 625.69 183.46 121.6 45 0.47
RAPT 6.6.8.0 Project Name: J110 Page 15/26 RAPT 6.6.8.0 Project Name: J110 Page 16/26
Licensee: AECOM Singapore Pte Ltd 1/7/2022 10:16:33 AM License No.: 10479063400712WPN11 Licensee: AECOM Singapore Pte Ltd 1/7/2022 10:16:36 AM License No.: 10479063400712WPN11
Locat V* Mv* Pv Mdec d Ast bv phi Vuc phi Vut phi Vu Phi Vumax phi VuMin phi Vus Theta Asv/s Span 3
Locat V* Mv* Pv Mdec d Ast bv phi Vuc phi Vut phi Vu Phi Vumax phi VuMin phi Vus Theta Asv/s
mm1 2 3 4 5 mm1 2 3 4 5
0 0
0.406
-1.85 -1.94 -2.44 -2.53
-9 -5.41 -4.21 -9 -5.43
-18 -18
-27 -27
-36 1479 1663 3031 3298 -36 3278 1290 13779 2531
0 8000 15000 20600 27000mm 0 8000 15000 20600 27000mm
Even Spans Loaded Odd Spans Loaded All Spans Loaded All Spans Loaded Odd Spans Loaded Even Spans Loaded
Incremental Incremental
mm1 2 3 4 5 mm1 2 3 4 5
0 0
-2.84 -1.29
-9 -4.01 -9 -4.6
-7.91 -6.14
-9.11 -9.14
-18 -18
-27 -27
-36 878 885 1975 1597 -36 1303 766 4327 1393
0 8000 15000 20600 27000mm 0 8000 15000 20600 27000mm
Even Spans Loaded Odd Spans Loaded All Spans Loaded All Spans Loaded Odd Spans Loaded Even Spans Loaded
mm1 2 3 4 5 mm1 2 3 4 5
0 0
-3.52 -1.97
-9 -4.96 -9 -5.55
-9.21 -9 -10.4
-12
-18 -18
-27 -27
-36 668 760 1591 1291 -36 889 671 2844 1154
0 8000 15000 20600 27000mm 0 8000 15000 20600 27000mm
Even Spans Loaded Odd Spans Loaded All Spans Loaded All Spans Loaded Odd Spans Loaded Even Spans Loaded
mm1 2 3 4 5 mm1 2 3 4 5
0 0
-2.11 -1.08 -0.53 -1.02 -2.11 -1.08 -0.53 -1.02
-9 -9
-18 -18
-27 -27
-36 3787 6458 10558 6259 -36 3787 6458 10558 6259
0 8000 15000 20600 27000mm 0 8000 15000 20600 27000mm
RAPT 6.6.8.0 Project Name: J110 Page 21/26 RAPT 6.6.8.0 Project Name: J110 Page 22/26
Licensee: AECOM Singapore Pte Ltd 1/7/2022 10:16:54 AM License No.: 10479063400712WPN11 Licensee: AECOM Singapore Pte Ltd 1/7/2022 10:16:57 AM License No.: 10479063400712WPN11
Short Term Top Reinforcement Bottom Reinforcement
Detailed Reinforcement
Span 1
Top Reinforcement Bottom Reinforcement Span 2
Top Reinforcement Bottom Reinforcement
Max Section Max Section
Locat Space Area Depth Width Rebar Reqd Space Area Depth Width Rebar Reqd Max Section Max Section
mm mm mm2 mm mm A mm mm2 mm mm A Locat Space Area Depth Width Rebar Reqd Space Area Depth Width Rebar Reqd
mm mm mm2 mm mm A mm mm2 mm mm A
100 0 0 61 200 No Steel Added 300 0 639 300 No Steel Added
560 0 0 61 200 No Steel Added 300 0 639 300 No Steel Added 250 300 0 61 200 No Steel Added 0 0 639 300 No Steel Added
699 0 0 61 200 No Steel Added 300 0 639 300 No Steel Added 530 300 0 61 200 No Steel Added 0 0 639 300 No Steel Added
701 0 0 61 200 No Steel Added 300 0 639 300 No Steel Added 810 300 0 61 200 No Steel Added 0 0 639 300 No Steel Added
960 0 0 61 200 No Steel Added 300 0 639 300 No Steel Added 1045 300 0 61 200 No Steel Added 0 0 639 300 No Steel Added
1219 0 0 61 200 No Steel Added 300 0 639 300 No Steel Added 1280 300 0 61 200 No Steel Added 0 0 639 300 No Steel Added
1478 0 0 61 200 No Steel Added 300 0 639 300 No Steel Added 1515 300 0 61 200 No Steel Added 300 0 639 300 No Steel Added
1737 0 0 61 200 No Steel Added 300 0 639 300 No Steel Added 1750 300 0 61 200 No Steel Added 300 0 639 300 No Steel Added
2000 0 0 61 200 No Steel Added 300 0 639 300 No Steel Added 1799 300 0 61 200 No Steel Added 300 0 639 300 No Steel Added
2666 0 0 61 200 No Steel Added 300 0 639 300 No Steel Added 1801 300 0 61 200 No Steel Added 300 0 639 300 No Steel Added
3332 0 0 61 200 No Steel Added 300 0 639 300 No Steel Added 1849 300 0 61 200 No Steel Added 300 0 639 300 No Steel Added
4000 0 0 61 200 No Steel Added 300 0 639 300 No Steel Added 1851 300 0 61 200 No Steel Added 300 0 639 300 No Steel Added
4309 0 0 61 200 No Steel Added 300 0 639 300 No Steel Added 2499 0 0 61 200 No Steel Added 300 0 639 300 No Steel Added
4311 0 0 61 200 No Steel Added 300 0 639 300 No Steel Added 2501 0 0 61 200 No Steel Added 300 0 639 300 No Steel Added
4999 0 0 61 200 No Steel Added 300 0 639 300 No Steel Added 2549 0 0 61 200 No Steel Added 300 0 639 300 No Steel Added
5001 0 0 61 200 No Steel Added 300 0 639 300 No Steel Added 2551 0 0 61 200 No Steel Added 300 0 639 300 No Steel Added
5009 0 0 61 200 No Steel Added 300 0 639 300 No Steel Added 3199 0 0 61 200 No Steel Added 300 0 639 300 No Steel Added
RAPT 6.6.8.0 Project Name: J110 Page 23/26 RAPT 6.6.8.0 Project Name: J110 Page 24/26
Licensee: AECOM Singapore Pte Ltd 1/7/2022 10:17:01 AM License No.: 10479063400712WPN11 Licensee: AECOM Singapore Pte Ltd 1/7/2022 10:17:04 AM License No.: 10479063400712WPN11
Top Reinforcement Bottom Reinforcement
Span 3
Max Section Max Section
Top Reinforcement Bottom Reinforcement
Locat Space Area Depth Width Rebar Reqd Space Area Depth Width Rebar Reqd
mm mm mm2 mm mm A mm mm2 mm mm A
Max Section Max Section
3201 0 0 61 200 No Steel Added 300 0 639 300 No Steel Added
Locat Space Area Depth Width Rebar Reqd Space Area Depth Width Rebar Reqd
3500 0 0 61 200 No Steel Added 300 0 639 300 No Steel Added mm mm mm2 mm mm A mm mm2 mm mm A
3899 0 0 61 200 No Steel Added 300 0 639 300 No Steel Added
250 300 0 61 200 No Steel Added 0 0 639 300 No Steel Added
3901 0 0 61 200 No Steel Added 300 0 639 300 No Steel Added
449 300 0 61 200 No Steel Added 0 0 639 300 No Steel Added
4499 0 0 61 200 No Steel Added 300 0 639 300 No Steel Added
649 300 0 61 200 No Steel Added 0 0 639 300 No Steel Added
4501 0 0 61 200 No Steel Added 300 0 639 300 No Steel Added
651 300 0 61 200 No Steel Added 0 0 639 300 No Steel Added
4599 0 0 61 200 No Steel Added 300 0 639 300 No Steel Added
810 300 0 61 200 No Steel Added 0 0 639 300 No Steel Added
4601 0 0 61 200 No Steel Added 300 0 639 300 No Steel Added
1054 300 0 61 200 No Steel Added 0 0 639 300 No Steel Added
5199 0 0 61 200 No Steel Added 300 0 639 300 No Steel Added
1299 300 0 61 200 No Steel Added 0 0 639 300 No Steel Added
5201 0 0 61 200 No Steel Added 300 0 639 300 No Steel Added
1301 300 0 61 200 No Steel Added 0 0 639 300 No Steel Added
5250 300 0 61 200 No Steel Added 300 0 639 300 No Steel Added
1349 300 0 61 200 No Steel Added 300 0 639 300 No Steel Added
5399 300 0 61 200 No Steel Added 300 0 639 300 No Steel Added
1351 300 0 61 200 No Steel Added 300 0 639 300 No Steel Added
5401 300 0 61 200 No Steel Added 300 0 639 300 No Steel Added
1400 300 0 61 200 No Steel Added 300 0 639 300 No Steel Added
5500 300 0 61 200 No Steel Added 300 0 639 300 No Steel Added
1699 300 0 61 200 No Steel Added 300 0 639 300 No Steel Added
5800 300 0 61 200 No Steel Added 0 0 639 300 No Steel Added
1999 0 0 61 200 No Steel Added 300 0 639 300 No Steel Added
6099 300 0 61 200 No Steel Added 0 0 639 300 No Steel Added
2001 0 0 61 200 No Steel Added 300 0 639 300 No Steel Added
6101 300 0 61 200 No Steel Added 0 0 639 300 No Steel Added
2399 0 0 61 200 No Steel Added 300 0 639 300 No Steel Added
6190 300 0 61 200 No Steel Added 0 0 639 300 No Steel Added
2401 0 0 61 200 No Steel Added 300 0 639 300 No Steel Added
6299 300 0 61 200 No Steel Added 0 0 639 300 No Steel Added
2800 0 0 61 200 No Steel Added 300 0 639 300 No Steel Added
6301 300 0 61 200 No Steel Added 0 0 639 300 No Steel Added
3201 0 0 61 200 No Steel Added 300 0 639 300 No Steel Added
6526 300 0 61 200 No Steel Added 0 0 639 300 No Steel Added
3600 0 0 61 200 No Steel Added 300 0 639 300 No Steel Added
6750 300 0 61 200 No Steel Added 0 0 639 300 No Steel Added
3999 0 0 61 200 No Steel Added 300 0 639 300 No Steel Added
Shear Reinforcement
4001 0 0 61 200 No Steel Added 300 0 639 300 No Steel Added
Spacing of Sets
4200 0 0 61 200 No Steel Added 300 0 639 300 No Steel Added
2 legs 4 legs 6 legs Min legs Minimum Shear
4398 300 0 61 200 No Steel Added 300 0 639 300 No Steel Added
Area T10 T10 T10 T10 Legs Comments
mm2/mm mm mm mm mm # A 4594 300 0 61 200 No Steel Added 0 0 639 300 No Steel Added
0.2 486.8 486.8 486.8 486.8 2 Minimum Steel 4790 300 0 61 200 No Steel Added 0 0 639 300 No Steel Added
0.2 486.8 486.8 486.8 486.8 2 Minimum Steel 4978 300 0 61 200 No Steel Added 0 0 639 300 No Steel Added
0.2 486.8 486.8 486.8 486.8 2 Minimum Steel 5164 300 0 61 200 No Steel Added 0 0 639 300 No Steel Added
0.37 425.7 486.8 486.8 425.7 2 5350 300 0 61 200 No Steel Added 0 0 639 300 No Steel Added
0.51 308.3 486.8 486.8 308.3 2 Shear Reinforcement
0.6 261 486.8 486.8 261 2 Spacing of Sets
0.56 279.1 486.8 486.8 279.1 2 2 legs 4 legs 6 legs Min legs Minimum Shear
Area T10 T10 T10 T10 Legs Comments
0.56 282.3 486.8 486.8 282.3 2 mm2/mm mm mm mm mm # A
0.56 282.4 486.8 486.8 282.4 2
0.2 489.4 489.4 489.4 489.4 2 Minimum Steel
0.55 285.6 486.8 486.8 285.6 2
0.2 489.4 489.4 489.4 489.4 2 Minimum Steel
0.55 285.7 486.8 486.8 285.7 2
0.2 489.4 489.4 489.4 489.4 2 Minimum Steel
0.47 332.2 486.8 486.8 332.2 2
0.2 489.4 489.4 489.4 489.4 2 Minimum Steel
0.47 332.3 486.8 486.8 332.3 2
0.23 489.4 489.4 489.4 489.4 2
0.47 335.1 486.8 486.8 335.1 2
0.5 315 489.4 489.4 315 2
0.47 335.2 486.8 486.8 335.2 2
0.6 260.6 486.8 486.8 260.6 2
0.39 399.7 486.8 486.8 399.7 2
0.49 319.2 486.8 486.8 319.2 2
0.39 399.8 486.8 486.8 399.8 2
0.52 304.2 486.8 486.8 304.2 2
0.33 469.1 486.8 486.8 469.1 2
0.66 238.1 476.2 486.8 238.1 2
0.37 426 486.8 486.8 426 2
0.68 231.7 463.4 486.8 231.7 2
0.37 425.7 486.8 486.8 425.7 2
0.66 238.6 477.1 486.8 238.6 2
0.44 357 486.8 486.8 357 2
0.65 241.4 482.8 486.8 241.4 2
0.44 356.9 486.8 486.8 356.9 2
0.65 241.4 482.8 486.8 241.4 2
0.45 350.7 486.8 486.8 350.7 2
0.64 245.2 486.8 486.8 245.2 2
0.45 350.6 486.8 486.8 350.6 2
0.26 486.8 486.8 486.8 486.8 2
0.52 299.3 486.8 486.8 299.3 2
0.24 486.8 486.8 486.8 486.8 2
0.52 299.1 486.8 486.8 299.1 2
0.25 486.8 486.8 486.8 486.8 2
0.53 295.6 486.8 486.8 295.6 2
0.26 486.8 486.8 486.8 486.8 2
0.54 288.5 486.8 486.8 288.5 2
0.27 486.8 486.8 486.8 486.8 2
0.71 222 300 300 222 2
0.63 250.8 486.8 486.8 250.8 2
0.72 216.7 300 300 216.7 2
0.57 274.2 486.8 486.8 274.2 2
0.79 199.3 300 300 199.3 2
0.47 333.3 486.8 486.8 333.3 2
0.77 203.7 300 300 203.7 2
0.35 443.8 486.8 486.8 443.8 2
0.77 203.9 300 300 203.9 2
0.2 489.4 489.4 489.4 489.4 2 Minimum Steel
0.72 217.9 300 300 217.9 2
0.2 489.4 489.4 489.4 489.4 2 Minimum Steel
0.52 301 489.4 489.4 301 2
0.2 489.4 489.4 489.4 489.4 2 Minimum Steel
0.52 303.4 489.4 489.4 303.4 2
0.2 489.4 489.4 489.4 489.4 2 Minimum Steel
0.2 489.4 489.4 489.4 489.4 2 Minimum Steel
0.2 489.4 489.4 489.4 489.4 2 Minimum Steel
RAPT 6.6.8.0 Project Name: J110 Page 25/26 RAPT 6.6.8.0 Project Name: J110 Page 26/26
Licensee: AECOM Singapore Pte Ltd 1/7/2022 10:17:08 AM License No.: 10479063400712WPN11 Licensee: AECOM Singapore Pte Ltd 1/7/2022 10:17:11 AM License No.: 10479063400712WPN11
Span 4 Shear Reinforcement
Top Reinforcement Bottom Reinforcement Spacing of Sets
2 legs 4 legs 6 legs Min legs Minimum Shear
Max Section Max Section Area T10 T10 T10 T10 Legs Comments
Locat Space Area Depth Width Rebar Reqd Space Area Depth Width Rebar Reqd mm2/mm mm mm mm mm # A
mm mm mm2 mm mm A mm mm2 mm mm A 0.2 486.8 486.8 486.8 486.8 2 Minimum Steel
250 300 0 61 200 No Steel Added 0 0 639 300 No Steel Added 0.2 486.8 486.8 486.8 486.8 2 Minimum Steel
474 300 0 61 200 No Steel Added 0 0 639 300 No Steel Added 0.2 486.8 486.8 486.8 486.8 2 Minimum Steel
699 300 0 61 200 No Steel Added 0 0 639 300 No Steel Added 0.2 486.8 486.8 486.8 486.8 2 Minimum Steel
701 300 0 61 200 No Steel Added 0 0 639 300 No Steel Added 0.2 486.8 486.8 486.8 486.8 2 Minimum Steel
810 300 0 61 200 No Steel Added 0 0 639 300 No Steel Added 0.2 486.8 486.8 486.8 486.8 2 Minimum Steel
899 300 0 61 200 No Steel Added 0 0 639 300 No Steel Added 0.2 486.8 486.8 486.8 486.8 2 Minimum Steel
901 300 0 61 200 No Steel Added 0 0 639 300 No Steel Added 0.2 486.8 486.8 486.8 486.8 2 Minimum Steel
1133 300 0 61 200 No Steel Added 0 0 639 300 No Steel Added 0.2 486.8 486.8 486.8 486.8 2 Minimum Steel
1365 300 0 61 200 No Steel Added 0 0 639 300 No Steel Added 0.2 486.8 486.8 486.8 486.8 2 Minimum Steel
1599 300 0 61 200 No Steel Added 300 0 639 300 No Steel Added 0.2 486.8 486.8 486.8 486.8 2 Minimum Steel
1601 300 0 61 200 No Steel Added 300 0 639 300 No Steel Added 0.2 486.8 486.8 486.8 486.8 2 Minimum Steel
1799 300 0 61 200 No Steel Added 300 0 639 300 No Steel Added 0.2 486.8 486.8 486.8 486.8 2 Minimum Steel
1801 300 0 61 200 No Steel Added 300 0 639 300 No Steel Added 0.2 486.8 486.8 486.8 486.8 2 Minimum Steel
1809 300 0 61 200 No Steel Added 300 0 639 300 No Steel Added 0.2 486.8 486.8 486.8 486.8 2 Minimum Steel
1811 300 0 61 200 No Steel Added 300 0 639 300 No Steel Added 0.2 486.8 486.8 486.8 486.8 2 Minimum Steel
2155 0 0 61 200 No Steel Added 300 0 639 300 No Steel Added 0.2 486.8 486.8 486.8 486.8 2 Minimum Steel
2499 0 0 61 200 No Steel Added 300 0 639 300 No Steel Added 0.2 486.8 486.8 486.8 486.8 2 Minimum Steel
2501 0 0 61 200 No Steel Added 300 0 639 300 No Steel Added 0.2 486.8 486.8 486.8 486.8 2 Minimum Steel
2509 0 0 61 200 No Steel Added 300 0 639 300 No Steel Added 0.2 486.8 486.8 486.8 486.8 2 Minimum Steel
2511 0 0 61 200 No Steel Added 300 0 639 300 No Steel Added 0.2 486.8 486.8 486.8 486.8 2 Minimum Steel
2799 0 0 61 200 No Steel Added 300 0 639 300 No Steel Added 0.2 486.8 486.8 486.8 486.8 2 Minimum Steel
2801 0 0 61 200 No Steel Added 300 0 639 300 No Steel Added
3200 0 0 61 200 No Steel Added 300 0 639 300 No Steel Added
3599 0 0 61 200 No Steel Added 300 0 639 300 No Steel Added
3601 0 0 61 200 No Steel Added 300 0 639 300 No Steel Added
4199 0 0 61 200 No Steel Added 300 0 639 300 No Steel Added Reinforcement Layout
4201 0 0 61 200 No Steel Added 300 0 639 300 No Steel Added
1 2 3 4 5
(3-T25)
(3-T25)
(3-T25)
(3-T25)
(3-T25)
(3-T32)
4299 0 0 61 200 No Steel Added 300 0 639 300 No Steel Added
(2-T25)
(2-T25)
(3-T25)
(3-T32)
4301 0 0 61 200 No Steel Added 300 0 639 300 No Steel Added mm
4800 0 0 61 200 No Steel Added 300 0 639 300 No Steel Added 0
4899 0 0 61 200 No Steel Added 300 0 639 300 No Steel Added
-200
4901 0 0 61 200 No Steel Added 300 0 639 300 No Steel Added
5135 0 0 61 200 No Steel Added 300 0 639 300 No Steel Added -400
5367 0 0 61 200 No Steel Added 300 0 639 300 No Steel Added
5599 0 0 61 200 No Steel Added 300 0 639 300 No Steel Added -600
(3-T25)
(3-T25)
(3-T32)
5601 0 0 61 200 No Steel Added 300 0 639 300 No Steel Added -800
5699 0 0 61 200 No Steel Added 300 0 639 300 No Steel Added
5701 0 0 61 200 No Steel Added 300 0 639 300 No Steel Added 0 8000 15000 20600 27000mm
5840 0 0 61 200 No Steel Added 300 0 639 300 No Steel Added
6070 0 0 61 200 No Steel Added 300 0 639 300 No Steel Added
6300 0 0 61 200 No Steel Added 300 0 639 300 No Steel Added
Shear Reinforcement
Spacing of Sets
2 legs 4 legs 6 legs Min legs Minimum Shear
Area T10 T10 T10 T10 Legs Comments
mm2/mm mm mm mm mm # A
0.2 489.4 489.4 489.4 489.4 2 Minimum Steel
0.2 489.4 489.4 489.4 489.4 2 Minimum Steel
0.2 489.4 489.4 489.4 489.4 2 Minimum Steel
0.2 489.4 489.4 489.4 489.4 2 Minimum Steel
0.21 489.4 489.4 489.4 489.4 2
0.27 489.4 489.4 489.4 489.4 2
0.27 489.4 489.4 489.4 489.4 2
0.32 489.4 489.4 489.4 489.4 2
0.29 486.8 486.8 486.8 486.8 2
0.28 486.8 486.8 486.8 486.8 2
0.31 486.8 486.8 486.8 486.8 2
0.3 486.8 486.8 486.8 486.8 2
0.23 486.8 486.8 486.8 486.8 2
0.23 486.8 486.8 486.8 486.8 2
0.23 486.8 486.8 486.8 486.8 2
0.2 486.8 486.8 486.8 486.8 2 Minimum Steel
0.2 486.8 486.8 486.8 486.8 2 Minimum Steel
0.2 486.8 486.8 486.8 486.8 2 Minimum Steel
0.2 486.8 486.8 486.8 486.8 2 Minimum Steel
RAPT 6.6.8.0 Project Name: J110 Page 2/14
Licensee: AECOM Singapore Pte Ltd 1/7/2022 9:55:25 AM License No.: 10479063400712WPN11
Frame Description: CB119- SIMILAR TO CB122
Project Name: J110 Beams
Project Number: 60628288 Beam Beam Beam Beam Effective
Frame Description: CB119- SIMILAR TO CB122 Number Depth Width Width Flange
Designer: SLT at Width
Slab
C:\Users\sujeevanleonard.tham\OneDrive - AECOM\Projects\J110\J110\OneDrive_2021-07-01\12. Southern mm mm mm mm
Staircase\Design Files\Str\Beams\Beam-Existing\CB119.rpf 1 550 200 200 200
Concrete Tensile Strength for Deflection Calculations- #.## x (Fc)n #.# -1 -400
Maximum Value of Ieff/Igross for Deflection Calculations #.# 0.6
Total Deflection Warning Limit - Maximum Span/Deflection #.# 250
Total Deflection Warning Limit - Maximum Deflection mm 25 0 6000mm
Incremental Deflection Warning Limit - Maximum Span/Deflection #.# 360
Incremental Deflection Warning Limit - Maximum Deflection mm 25
Initial Time for Shrinkage List Full Shrinkage
RAPT 6.6.8.0 Project Name: J110 Page 7/14 RAPT 6.6.8.0 Project Name: J110 Page 8/14
Licensee: AECOM Singapore Pte Ltd 1/7/2022 9:55:40 AM License No.: 10479063400712WPN11 Licensee: AECOM Singapore Pte Ltd 1/7/2022 9:55:43 AM License No.: 10479063400712WPN11
Frame Description: CB119- SIMILAR TO CB122 Frame Description: CB119- SIMILAR TO CB122
Plan view Ultimate Design
Flexure
mm1 2
-100 kNm1 2
-20
-50 0 6.68 6.68
20
0
40
60
50
80
100 100
0 6000mm 102
120
Warnings 0 6000mm
Input
Moment Moment 1 Moment 2
No errors or warnings were found.
Output 1 2
Warning:At 1025mm, the moment curvature calculations did not converge on the design moment within our set limits after 100 iterations. We have adopted kN
the nearest solution. This normally only occurs at points of very low moment and is not normally a problem so we have continued with the design. 80 65.7
60
40
20
0
Bending Moments -20
-40
Load Cases -60
Column Actions -80 -65.7
Col No. 1 Self Extra Dead Live 0 6000mm
Weight Load Load
Moment Above kNm -0 -0 -0 Shear Shear 1 Shear 2
Moment Below kNm -0 -0 -0
Reaction kN 8.25 30 9
Elastic Rotation #.# 3.05e-4 1.11e-3 3.32e-4 Shear
Elastic Axial Shortening mm 0 0 0
kNm1 2
-20
Col No. 2 Self Extra Live Load 6.68 6.68
Weight Dead 0
Load 20
Moment Above kNm -0 -0 -0
40
Moment Below kNm -0 -0 -0
Reaction kN 8.25 30 9 60
Elastic Rotation #.# -3.05e-4 -1.11e-3 -3.32e-4 80
Elastic Axial Shortening mm 0 0 0 100 91.1
120
0 6000mm
Gross Stress Top Gross Stress Bottom Cracked Compression Reinforcement Tension
1 2
0.03 Reversal Moment Condition
0
-0.03 1 2
-0.06 MPa MPa
-6 -4.35 -120
-0.09
-0.12 -4 -80
-0.15 -2 -40
-0.18 0 0
0.19
-0.21 2 40
0 6000mm
4 80
Neutral Axis Depth Initial Final 6 120
4.79
0 6000mm
Service Gross Stress Top Gross Stress Bottom Cracked Compression Reinforcement Tension
Maximum Moment Condition
Gross Stress Top Gross Stress Bottom Cracked Compression Reinforcement Tension
RAPT 6.6.8.0 Project Name: J110 Page 11/14 RAPT 6.6.8.0 Project Name: J110 Page 12/14
Licensee: AECOM Singapore Pte Ltd 1/7/2022 9:55:52 AM License No.: 10479063400712WPN11 Licensee: AECOM Singapore Pte Ltd 1/7/2022 9:55:55 AM License No.: 10479063400712WPN11
Frame Description: CB119- SIMILAR TO CB122 Frame Description: CB119- SIMILAR TO CB122
Reversal Moment Condition
1 2
MPa MPa Punching
-8 -5.08 -160
-6 -120 Column Head Critical Section
-4 -80 Column Bh a at u d fcv P/A Asw/s min V* Mv* V*eff Vu Vumax Asv result
-2 -40 No.
0 0 A #.# mm mm mm mm MPa MPa mm2/mm kN kNm kN kN kN mm2 A
2 40 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Check Not Carried Out!
4 80
2 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Check Not Carried Out!
6 120
8 160
10 5.59 200
0 6000mm
Gross Stress Top Gross Stress Bottom Cracked Compression Reinforcement Tension Deflections
All Spans Loaded
Transfer
Shear Design
Beam mm1 2
Span 1 0
Locat V* Mv* Pv Mdec d Ast bv phi Vuc phi Vut phi Vu Phi Vumax phi VuMin phi Vus Theta Asv/s -0.892
-10
(2-T16)
Top Reinforcement Bottom Reinforcement 1 2
mm
0
Max Section Max Section
Locat Space Area Depth Width Rebar Reqd Space Area Depth Width Rebar Reqd
mm mm mm2 mm mm A mm mm2 mm mm A -200
100 0 0 61 200 No Steel Added 300 0 489 200 No Steel Added
440 0 0 61 200 No Steel Added 300 0 489 200 No Steel Added
549 0 0 61 200 No Steel Added 300 0 489 200 No Steel Added -400
551 0 0 61 200 No Steel Added 300 0 489 200 No Steel Added
(2-T25)
788 0 0 61 200 No Steel Added 300 0 489 200 No Steel Added
1025 0 0 61 200 No Steel Added 300 0 489 200 No Steel Added 0 6000mm
1262 0 0 61 200 No Steel Added 300 0 489 200 No Steel Added
1500 0 0 61 200 No Steel Added 300 0 489 200 No Steel Added
2000 0 0 61 200 No Steel Added 300 0 489 200 No Steel Added
2500 0 0 61 200 No Steel Added 300 0 489 200 No Steel Added
3000 0 0 61 200 No Steel Added 300 0 489 200 No Steel Added
3500 0 0 61 200 No Steel Added 300 0 489 200 No Steel Added
4000 0 0 61 200 No Steel Added 300 0 489 200 No Steel Added
4500 0 0 61 200 No Steel Added 300 0 489 200 No Steel Added
4738 0 0 61 200 No Steel Added 300 0 489 200 No Steel Added
4975 0 0 61 200 No Steel Added 300 0 489 200 No Steel Added
5212 0 0 61 200 No Steel Added 300 0 489 200 No Steel Added
5449 0 0 61 200 No Steel Added 300 0 489 200 No Steel Added
5451 0 0 61 200 No Steel Added 300 0 489 200 No Steel Added
5560 0 0 61 200 No Steel Added 300 0 489 200 No Steel Added
5900 0 0 61 200 No Steel Added 300 0 489 200 No Steel Added
Shear Reinforcement
Spacing of Sets
2 legs 4 legs 6 legs Min legs Minimum Shear
Area T10 T10 T10 T10 Legs Comments
mm2/mm mm mm mm mm # A
0.2 369.4 369.4 369.4 369.4 2 Minimum Steel
0.2 369.4 369.4 369.4 369.4 2 Minimum Steel
0.2 369.4 369.4 369.4 369.4 2 Minimum Steel
0.2 369.4 369.4 369.4 369.4 2 Minimum Steel
0.2 369.4 369.4 369.4 369.4 2 Minimum Steel
0.2 369.4 369.4 369.4 369.4 2 Minimum Steel
0.2 369.4 369.4 369.4 369.4 2 Minimum Steel
0.2 369.4 369.4 369.4 369.4 2 Minimum Steel
0.2 369.4 369.4 369.4 369.4 2 Minimum Steel
0.2 369.4 369.4 369.4 369.4 2 Minimum Steel
0.2 369.4 369.4 369.4 369.4 2 Minimum Steel
0.2 369.4 369.4 369.4 369.4 2 Minimum Steel
0.2 369.4 369.4 369.4 369.4 2 Minimum Steel
0.2 369.4 369.4 369.4 369.4 2 Minimum Steel
0.2 369.4 369.4 369.4 369.4 2 Minimum Steel
0.2 369.4 369.4 369.4 369.4 2 Minimum Steel
0.2 369.4 369.4 369.4 369.4 2 Minimum Steel
0.2 369.4 369.4 369.4 369.4 2 Minimum Steel
0.2 369.4 369.4 369.4 369.4 2 Minimum Steel
0.2 369.4 369.4 369.4 369.4 2 Minimum Steel
0.2 369.4 369.4 369.4 369.4 2 Minimum Steel
RAPT 6.6.8.0 Project Name: J110 Page 2/14
Licensee: AECOM Singapore Pte Ltd 1/7/2022 9:49:25 AM License No.: 10479063400712WPN11
Frame Description: CB127-SIMILAR TO CB129
Project Name: J110 Beams
Project Number: 60628288 Beam Beam Beam Beam Effective
Frame Description: CB127-SIMILAR TO CB129 Number Depth Width Width Flange
Designer: SLT at Width
Slab
C:\Users\sujeevanleonard.tham\OneDrive - AECOM\Projects\J110\J110\OneDrive_2021-07-01\12. Southern mm mm mm mm
Staircase\Design Files\Str\Beams\Beam-Existing\CB127.rpf 1 550 200 200 200
Concrete Tensile Strength for Deflection Calculations- #.## x (Fc)n #.# -1 -400
Maximum Value of Ieff/Igross for Deflection Calculations #.# 0.6
Total Deflection Warning Limit - Maximum Span/Deflection #.# 250
Total Deflection Warning Limit - Maximum Deflection mm 25 0 7075mm
Incremental Deflection Warning Limit - Maximum Span/Deflection #.# 360
Incremental Deflection Warning Limit - Maximum Deflection mm 25
Initial Time for Shrinkage List Full Shrinkage
RAPT 6.6.8.0 Project Name: J110 Page 7/14 RAPT 6.6.8.0 Project Name: J110 Page 8/14
Licensee: AECOM Singapore Pte Ltd 1/7/2022 9:49:40 AM License No.: 10479063400712WPN11 Licensee: AECOM Singapore Pte Ltd 1/7/2022 9:49:43 AM License No.: 10479063400712WPN11
Frame Description: CB127-SIMILAR TO CB129 Frame Description: CB127-SIMILAR TO CB129
Plan view Ultimate Design
Flexure
mm1 2
-100 kNm1 2
-20
-50 5.6 5.6
0
20
0
40
50 60
80
100 100
0 7075mm 101
120
Warnings 0 7075mm
Input
No errors or warnings were found. Moment Moment 1 Moment 2
Output 1 2
Warning:Incremental Deflection span/deflection ratio in at least one span is less than defined limit. kN 55.2
60
40
20
0
Bending Moments
-20
Load Cases
-40
Column Actions
-60
Col No. 1 Self Extra Dead Live -55.2
Weight Load Load 0 7075mm
Moment Above kNm -0 -0 -0
Moment Below kNm -0 -0 -0 Shear Shear 1 Shear 2
Reaction kN 9.73 22.99 6.9
Elastic Rotation #.# 4.99e-4 1.18e-3 3.54e-4
Elastic Axial Shortening mm 0 0 0
Shear
kNm1 2
Col No. 2 Self Extra Live Load -20
Weight Dead 5.6 5.6
Load 0
Moment Above kNm -0 -0 -0 20
Moment Below kNm -0 -0 -0