Professional Documents
Culture Documents
: 300
UNIT NO.: 265
PN: 265-94-XXX
267-97
PAGE: 1 OF 3
The Weatherford Arrow-Pak delivers high performance with simplicity of design and desirable
1.) Place setting sleeve (1) in vise. Remove shear screws (17), torque screws (15 & 20).
economics. The Arrow-Pak is set on wireline or on tubing and is easily retrieved. The short design of 2.) Remove set screws (22) from lower cone (21) and remove lower cone (21) from bottom (29).
the Arrow-Pak makes it ideal for use in horizontal or deviated wells. 3.) Remove bottom (29) from collet (23).
The Arrow-Pak is designed with a unique sealing system. This packing element system packs 4.) Remove set screws (24) from collet (23).
off easily and still resists swab-off during run in and retrieval of the packer. The Arrow-Pak has 5.) Remove collet (23) from mandrel (13) and remove o-rings (25 & 26).
proven itself in gravel pack applications as well as its ability to handle deep, high pressure
6.) Remove shear screws (27) from collet (23) and remove support ring (28) from collet (23).
completions.
7.) Remove lower cone (21) from mandrel (13).
8.) Remove upper cone (14) from lower retainer (12) and remove upper cone (14) and slip
cage assembly from mandrel (13).
SPECIFICATIONS GUIDE 9.) Remove slips (18) and slip springs (19) from slip cage (16). Remove upper cone (14) from
slip cage (16).
RECOMMENDED MIN. 10.) Remove setting sleeve (1) from the vise and place lower end of mandrel (13) in vise.
CASING PKR. PKR.
CASING RANGE BORE PRODUCT 11.) Remove shear screws (5) from setting sleeve (1). Remove setting sleeve (1) from setting
O.D. BORE
O.D. WEIGHT MIN. MAX. THROUGH NUMBER sleeve adapter (8). Remove set screw (6) and remove lock ring (7) from setting sleeve (1).
(IN.) (IN.) 12.) Remove top body (3) from mandrel (13). Remove o-ring (4) from top body (3).
(IN.) (LBS./FT.) (IN.) (IN.) SEALS
9-5/8 47.0 - 53.5 8.535 8.681 8.319 4.000 3.000 265-94-xxx 13.) Remove setting sleeve adapter (8) from upper retainer (9).
14.) Remove upper retainer (9) from mandrel (13).
15.) Remove packing element system (10) and lower retainer (12) from mandrel (13). Remove
lower gage ring (11) from lower retainer (12).
SETTING PROCEDURE 16.) Clean and inspect all parts. Replace any worn or damaged parts.
Run the Arrow-Pak in to setting depth on wireline pressure setting assembly using the Arrow-Pak ASSEMBLY
Wireline Adapter Kit or on tubing using a hydraulic setting tool.
Maximum recommended running speed of 180 ft/min.
1.) Place mandrel (13) in vise with grooves up. Slide upper cone (14) into slip cage (16) and install
shear screw (17). Install slip springs (19) and slips (18) into slip cage (16).
2.) Slide slip cage assembly (16) onto mandrel (13). Slide lower cone (21) onto mandrel (13) into
RELEASING PROCEDURE slip cage (16).
3.) Install collet support ring (28) inside of collet (23). Tap support ring (28) flush with collet
The retrieving tool is run in the hole and set down force is applied when the packer is contacted. A fingers and insert screws (27).
few points is sufficient to fully latch the retrieving tool into the packer. At this point, the release collet 4.) Install inner and outer o-rings (25 & 26) onto collet (23) and install collet (23) onto mandrel (13)
is positioned directly below the support ring of the packer. Straight pull will engage the release collet Install set screws (24) in collet (23).
and the support ring. Tension force is applied which will shear the screws in the support ring and shift 5.) Thread bottom (29) into lower cone (21). Rotate sub-assembly onto collet (23). Install set
it upward thus releasing the packer. screws (22) in lower cone (21). Install torque screws (15 & 20) in upper and lower cones
If the support ring does not shear out easily then there is a built in jar stroke in the retrieving tool. By (14 & 21).
jarring upward, either the support ring will shear or the shear ring in the retrieving tool will shear. This 6.) Place bottom (29) in vise. Place lower gage ring (11) onto lower retainer (12) and install lower
is a safety shear, which will enable the retrieving tool to be rotated free of the packer if the packer will retainer (12) onto upper cone (14).
not release. If this is necessary, pull slight tension and rotate to the right approximately 8 turns to 7.) Lubricate mandrel (13) where packing element (10) rests on mandrel (13). Install packing
release the retrieving tool from the packer. The shear value of the shear ring is adjustable and should element (10). NOTE: Make sure element system is flush with upper retainer (9) and
be considered prior to running the retrieving tool. gage ring (11).
8.) Install upper retainer (9) onto mandrel (13).
9.) Install top body (3) onto mandrel (13) and install o-ring (4).
10.) Install setting sleeve adapter (8) onto upper retainer (9).
11.) Install lock ring (7) in setting sleeve (1) and install set screw (6).
12.) Slide setting sleeve (1) onto top body (3) and install setting sleeve (1) onto setting sleeve
adapter (8).
13.) Install shear screws (5) in setting sleeve (1) and into groove in top body (3).
14.) Install shipping bolt and nut (2).
© 1999 WEATHERFORD All Rights Reserved. NORTH AMERICAN NUMBERS: HUNTSVILLE, TX PH:800/331-4042 USA 409/295-0080 FAX:409/295-9132 • POWELL, WY PH:307/754-7234 800/458-9202 USA FAX:307/754-5875 REV. 00/DTD: 06-09-99
INDEX NO.: 300
UNIT NO.: 265
PN: 265-94-XXX
267-97
PAGE: 2 OF 3
© 1999 WEATHERFORD All Rights Reserved. NORTH AMERICAN NUMBERS: HUNTSVILLE, TX PH:800/331-4042 USA 409/295-0080 FAX:409/295-9132 • POWELL, WY PH:307/754-7234 800/458-9202 USA FAX:307/754-5875 REV. 00/DTD: 06-09-99
INDEX NO.: 300
UNIT NO.: 265
PN: 265-94-XXX
267-97
PAGE: 3 OF 3
SIZE WEIGHT PRODUCT DIMENSIONS (IN.) SIZE WEIGHT PRODUCT DIMENSIONS (IN.)
(IN.) (LBS./FT.) NUMBER A B C D E F (IN.) (LBS./FT.) NUMBER G H J K L M
9-5/8 47.0 - 53.5 265-94-xxx 68.220 39.313 32.938 15.156 7.230 8.170 9-5/8 47.0 - 53.5 265-94-xxx 8.319 4.000 8.288 4.125 8.000 4.200
© 1999 WEATHERFORD All Rights Reserved. NORTH AMERICAN NUMBERS: HUNTSVILLE, TX PH:800/331-4042 USA 409/295-0080 FAX:409/295-9132 • POWELL, WY PH:307/754-7234 800/458-9202 USA FAX:307/754-5875 REV. 00/DTD: 06-09-99