Professional Documents
Culture Documents
Exam
Civil Engineering / Board Exam / Design and Construction
Question 1
Contributed by: System Admin
A stress-graded unseasoned Apitong with 80% stress grade is selected for use as a column.
The section size is 100 mm x 250 mm. The member is 3.6 m long, with weak way lateral support
at mid-height and lateral support both ways at each end. Assume all supports are pinned.
Allowable working stresses are given below:
Bending and tension parallel to grain 16.5 MPa
Compression parallel to grain 9.56 MPa
Compression perpendicular to grain 2.20 MPa
Modulus of Elasticity in Bending 7.31 GPa
Determine the classification of the column.
a. Short
b. Intermediate
c. Long
d. Not Allowed
Question 2
Contributed by: System Admin
A stress-graded unseasoned Apitong with 80% stress grade is selected for use as a column.
The section size is 100 mm x 250 mm. The member is 3.6 m long, with weak way lateral support
at mid-height and lateral support both ways at each end. Assume all supports are pinned.
Allowable working stresses are given below:
Bending and tension parallel to grain 16.5 MPa
Compression parallel to grain 9.56 MPa
Compression perpendicular to grain 2.20 MPa
Modulus of Elasticity in Bending 7.31 GPa
Which of the following gives the allowable compressive stress in MPa?
a. 6.73
b. 8.40
c. 9.56
d. 11.62
Question 3
Contributed by: System Admin
A stress-graded unseasoned Apitong with 80% stress grade is selected for use as a column.
The section size is 100 mm x 250 mm. The member is 3.6 m long, with weak way lateral support
at mid-height and lateral support both ways at each end. Assume all supports are pinned.
Back
Allowable working stresses are given below:
Bending and tension parallel to grain 16.5 MPa
https://inhinyero.ph/exam/question 1/30
5/4/2020
Bending and tension parallel to grain 16.5Exam
MPa| Inhinyero - Student Portal
a. 239 kN
b. 210 kN
c. 168 kN
d. 135 kN
Question 4
Contributed by: System Admin
A flooring system consists of parallel I-beam sections spaced at 3m. on centers with simple
spans of 6 m. The beam supports a 200mm thick slab. The flooring system is designed for a
live load of 2400 N/m2 as well as ceiling load of 750 N/m2. The properties of the I=beam
sections are: d = 352mm, Ix = 0.00012m4, W = 440N/m, Fy = 248MPa, E = 200,000 GPa. Use Wt.
of concrete = 24kN/m3
38. Which of the following gives the uniform pressure acting on the slab.
a. 7.20 kPa
b. 7.95 kPa
c. 8.10 kPa
d. 8.39 kPa
Question 5
Contributed by: System Admin
A flooring system consists of parallel I-beam sections spaced at 3m. on centers with simple
spans of 6 m. The beam supports a 200mm thick slab. The flooring system is designed for a
live load of 2400 N/m2 as well as ceiling load of 750 N/m2. The properties of the I=beam
sections are: d = 352mm, Ix = 0.00012m4, W = 440N/m, Fy = 248MPa, E = 200,000 GPa. Use Wt.
of concrete = 24kN/m3
Which of the following gives the total uniform load carried by the beam in kN/m.
a. 21.60
b. 23.85
c. 24.29
d. 25.17
Question 6
Contributed by: System Admin
A flooring system consists of parallel I-beam sections spaced at 3m. on centers with simple
spans of 6 m. The beam supports a 200mm thick slab. The flooring system is designed for a Back
live load of 2400 N/m2 as well as ceiling load of 750 N/m2. The properties of the I=beam
https://inhinyero.ph/exam/question 2/30
5/4/2020 Exam | Inhinyero - Student Portal
sections are: d = 352mm, Ix = 0.00012m4, W = 440N/m, Fy = 248MPa, E = 200,000 GPa. Use Wt.
of concrete = 24kN/m3
Which of the following gives the maximum flexural stress on the steel beam considering non-
composite action.
a. 142.6 MPa
b. 157.4 MPa
c. 160.3 MPa
d. 166.1 MPa
Question 7
Contributed by: System Admin
Light-grade steel channel was used as a purlin of a truss. The top chord of the truss is
inclined 1V:3H and distance between trusses is equal to 3 m. The purlin has a weight of 71
N/m and spaced at 1.2 m, on centers. The dead load including the roof materials is 1200 Pa,
live load of 1000 Pa and wind load of 1440 Pa. Coefficient of pressure at leeward and
windward are 0.2 and 0.6 respectively. Sag rods are placed at the midpoint and Fbx=Fby=138
MPa. Sx=4.48 x 104 mm3 ; Sy=1.18 x 104 mm3
Calculate the bending stress, fbx, for dead load and live load combination (D+L)
a. 52.40 MPa
b. 62.89 MPa
c. 66.29 MPa
d. 75.47 MPa
Question 8
Contributed by: System Admin
Light-grade steel channel was used as a purlin of a truss. The top chord of the truss is
inclined 1V:3H and distance between trusses is equal to 3 m. The purlin has a weight of 71
N/m and spaced at 1.2 m, on centers. The dead load including the roof materials is 1200 Pa,
live load of 1000 Pa and wind load of 1440 Pa. Coefficient of pressure at leeward and
windward are 0.2 and 0.6 respectively. Sag rods are placed at the midpoint and Fbx=Fby=138
MPa. Sx=4.48 x 104 mm3 ; Sy=1.18 x 104 mm3
Calculate the maximum ratio of actual to the allowable bending stress for load combination
0.75 (D+L+W)
a. 0.55
b. 0.60
c. 0.71
d. 0.94
Question 9
Back
Contributed by: System Admin
https://inhinyero.ph/exam/question 3/30
5/4/2020 Exam | Inhinyero - Student Portal
Light-grade steel channel was used as a purlin of a truss. The top chord of the truss is
inclined 1V:3H and distance between trusses is equal to 3 m. The purlin has a weight of 71
N/m and spaced at 1.2 m, on centers. The dead load including the roof materials is 1200 Pa,
live load of 1000 Pa and wind load of 1440 Pa. Coefficient of pressure at leeward and
windward are 0.2 and 0.6 respectively. Sag rods are placed at the midpoint and Fbx=Fby=138
MPa. Sx=4.48 x 104 mm3 ; Sy=1.18 x 104 mm3
Determine the required diameter of the sagrod. The allowable tensile stress for this member
is Ft = 0.33Fu = 131 MPa. Assume the critical sagrod supports 6 lower purlins.
a. 9 mm
b. 10 mm
c. 12 mm
d. 16 mm
Question 10
Contributed by: System Admin
A W12x79 of A573 Grade 60 (Fy = 415 MPa) steel is used as a compression member. It is 8.5 m
long, pinned at the top fixed at bottom, and has additional support in the weak direction at
a point 3.4 m from the top. Properties of the section are as follows:
A = 14,500 mm^2
Ix = 258.6 x 10^6 mm^4
Iy = 84.375 x 10^6 mm^4
Calculate the effective slenderness ratio with respect to strong axis buckling.
a. 44.55
b. 63.65
c. 78.0
d. 111.43
Question 11
Contributed by: System Admin
A W12x79 of A573 Grade 60 (Fy = 415 MPa) steel is used as a compression member. It is 8.5 m
long, pinned at the top fixed at bottom, and has additional support in the weak direction at
a point 3.4 m from the top. Properties of the section are as follows:
A = 14,500 mm^2
Ix = 258.6 x 10^6 mm^4
Iy = 84.375 x 10^6 mm^4
Calculate the effective slenderness ratio with respect to weak axis buckling.
a. 44.57
b. 46.80
c. 64.23
d. 66.85
Back
,
https://inhinyero.ph/exam/question 4/30
5/4/2020 Exam | Inhinyero - Student Portal
Question 12
Contributed by: System Admin
A W12x79 of A573 Grade 60 (Fy = 415 MPa) steel is used as a compression member. It is 8.5 m
long, pinned at the top fixed at bottom, and has additional support in the weak direction at
a point 3.4 m from the top. Properties of the section are as follows:
A = 14,500 mm^2
Ix = 258.6 x 10^6 mm^4
Iy = 84.375 x 10^6 mm^4
Calculate the axial load capacity of the column.
a. 2 951 kN
b. 2 905 kN
c. 2 523 kN
d. 2 444 kN
Question 13
Contributed by: System Admin
In the connection shown in the figure Grade 50 steel (Fy = 50 ksi, Fu = 65 ksi) is used for
the tension member, A36 steel (Fy = 36 ksi, Fu = 58 ksi) is used for the gusset plate, and
the holes are for ¾-inch bolts.
Calculate the block shear strength of the gusset plate.
Image:
a. 60.63 kips
b. 76.39 kips
c. 92.44 kips
d. 138.93 kips
Question 14
Contributed by: System Admin
In the connection shown in the figure Grade 50 steel (Fy = 50 ksi, Fu = 65 ksi) is used for
the tension member, A36 steel (Fy = 36 ksi, Fu = 58 ksi) is used for the gusset plate, and
the holes are for ¾-inch bolts.
Calculate the block shear strength of the tension member.
Image:
Back
https://inhinyero.ph/exam/question 5/30
5/4/2020 Exam | Inhinyero - Student Portal
a. 56.89 kips
b. 71.69 kips
c. 86.74 kips
d. 130.37 kips
Question 15
Contributed by: System Admin
In the connection shown in the figure Grade 50 steel (Fy = 50 ksi, Fu = 65 ksi) is used for
the tension member, A36 steel (Fy = 36 ksi, Fu = 58 ksi) is used for the gusset plate, and
the holes are for ¾-inch bolts.
Calculate the allowable strength of the tension member based on net section fracture.
Image:
a. 74.35 kips
b. 77.76 kips
c. 84.27 kips
d. 99.14 kips
Question 16
Contributed by: System Admin
A W 600 x 110 beam is supported by a bearing plate 300 mm x 200 mm x 25 mm on a wall with a
thickness of 300 mm.
Properties of W 600 x 110 beam
d = 600 mm
bf = 225 mm
tf = 18 mm
tw = 12 mm
K = 36 mm
fc’ = 24 MPa
fy = 248 MPa Back
The allowable bearing stress is 0.35 fc’, allowable bending stress is 0.75 Fy and
https://inhinyero.ph/exam/question 6/30
5/4/2020 Exam | Inhinyero - Student Portal
allowable web yielding stress is 0.66 Fy. Determine the maximum reaction at the beam for the
following conditions.
Considering the bearing of concrete wall.
a. 1440 kN
b. 504 kN
c. 1224 kN
d. 360 kN
Question 17
Contributed by: System Admin
A W 600 x 110 beam is supported by a bearing plate 300 mm x 200 mm x 25 mm on a wall with a
thickness of 300 mm.
Properties of W 600 x 110 beam
d = 600 mm
bf = 225 mm
tf = 18 mm
tw = 12 mm
K = 36 mm
fc’ = 24 MPa
fy = 248 MPa
The allowable bearing stress is 0.35 fc’, allowable bending stress is 0.75 Fy and
allowable web yielding stress is 0.66 Fy. Determine the maximum reaction at the beam for the
following conditions.
Considering bending of plates at a distance K.
a. 333.6 kN
b. 178.9 kN
c. 168.2 kN
d. 193.5 kN
Question 18
Contributed by: System Admin
A W 600 x 110 beam is supported by a bearing plate 300 mm x 200 mm x 25 mm on a wall with a
thickness of 300 mm.
Properties of W 600 x 110 beam
d = 600 mm
bf = 225 mm
tf = 18 mm
tw = 12 mm
K = 36 mm
fc’ = 24 MPa
fy = 248 MPa
The allowable bearing stress is 0.35 fc’, allowable bending stress is 0.75 Fy and
allowable web yielding stress is 0.66 Fy. Determine the maximum reaction at the beam for the Back
following conditions.
https://inhinyero.ph/exam/question 7/30
5/4/2020 g Exam | Inhinyero - Student Portal
a. 569.61 kN
b. 792.3 kN
c. 436.6 kN
d. 839.21 kN
Question 19
Contributed by: System Admin
Light-grade steel channel was used as a purlin of a truss. The top chord of the truss is
inclined 1 V : 3 H and distance between trusses is equal to 3 m. The purlin has a weight of
71 kN/m and spaced at 1.2 m. on centers. The dead load including the roof materials is 1200
Pa, live load of 1000 Pa and wind load of 1440 Pa. Coefficient of pressure at leeward and
windward are 0.6 and 0.2 respectively. Sag rods are placed at the middle thirds and Fbx= Fby
= 138MPa.
Sx = 4.48 x 104 mm3
Sy = 1.18 x 104 mm3
Using interaction formula, determine the following:
Maximum ratio of actual to allowable bending stress for combination of (D + L) load.
a. 0.45
b. 0.66
c. 0.57
d. 0.72
Question 20
Contributed by: System Admin
Light-grade steel channel was used as a purlin of a truss. The top chord of the truss is
inclined 1 V : 3 H and distance between trusses is equal to 3 m. The purlin has a weight of
71 kN/m and spaced at 1.2 m. on centers. The dead load including the roof materials is 1200
Pa, live load of 1000 Pa and wind load of 1440 Pa. Coefficient of pressure at leeward and
windward are 0.6 and 0.2 respectively. Sag rods are placed at the middle thirds and Fbx= Fby
= 138MPa.
Sx = 4.48 x 104 mm3
Sy = 1.18 x 104 mm3
Using interaction formula, determine the following:
Maximum ratio of actual to allowable bending stress for combination of 0.75(D + L + W).
a. 0.75
b. 0.43
c. 0.66
d. 0.57
Back
,
Question 21
https://inhinyero.ph/exam/question 8/30
5/4/2020 Exam | Inhinyero - Student Portal
Question 21
Contributed by: System Admin
Light-grade steel channel was used as a purlin of a truss. The top chord of the truss is
inclined 1 V : 3 H and distance between trusses is equal to 3 m. The purlin has a weight of
71 kN/m and spaced at 1.2 m. on centers. The dead load including the roof materials is 1200
Pa, live load of 1000 Pa and wind load of 1440 Pa. Coefficient of pressure at leeward and
windward are 0.6 and 0.2 respectively. Sag rods are placed at the middle thirds and Fbx= Fby
= 138MPa.
Sx = 4.48 x 104 mm3
Sy = 1.18 x 104 mm3
Using interaction formula, determine the following:
Maximum ratio of actual to allowable bending stress for combination of (D + L) if one line of
sag rod was place at the mid-span.
a. 0.59
b. 0.65
c. 0.76
d. 0.47
Question 22
Contributed by: System Admin
A plate is used as a bracket and is attached to a column flange as shown in Fig. SIT-L.
Assume the base metal shear is adequate.
Calculate the direct shear load in the welds in N/mm.
Image:
a. 206.15
b. 187.04
c. 191.43
d. 270.76
Question 23
Contributed by: System Admin
A plate is used as a bracket and is attached to a column flange as shown in Fig. SIT-L.
Assume the base metal shear is adequate.
Calculate the maximum resultant load in the welds in N/mm.
Back
Image:
https://inhinyero.ph/exam/question 9/30
5/4/2020
g
Exam | Inhinyero - Student Portal
a. 427.89
b. 581.05
c. 466.98
d. 634.04
Question 24
Contributed by: System Admin
A plate is used as a bracket and is attached to a column flange as shown in Fig. SIT-L.
Assume the base metal shear is adequate.
Calculate the required size of the fillet weld if electrode E70xx is used with Fu = 482 MPa.
Image:
a. 4 mm
b. 5 mm
c. 6 mm
d. 7 mm
Question 25
Contributed by: System Admin
The floor system of a building consists of ribbed metal deck with 50 mm concrete slab on top.
The deck is supported by wide flange steel beams strengthened by cover plate 12 mm thick one
at the top and one at the bottom. It is simply supported on a span of 9 m. each of the
cover-plated steel beam is subjected to the following loads:
DL = 12 kN/m (including self weight)
LL = 20 kN/m
Properties of W830x175
A = 11,500 mm^2 bf = 250 mm
Back
d = 350 mm Ix = 266x10^6 mm^4
tw 10 mm
https://inhinyero.ph/exam/question
Iy 45 x10^6 mm^4 10/30
5/4/2020 Exam | Inhinyero - Student Portal
tw = 10 mm Iy = 45 x10^6 mm^4
tf = 16 mm Fy = 248 MPa
Calculate the available strength of the wide flange alone if its allowable bending stress is
0.66Fy.
a. 248.79
b. 225.45
c. 282.72
d. 272.67
Question 26
Contributed by: System Admin
The floor system of a building consists of ribbed metal deck with 50 mm concrete slab on top.
The deck is supported by wide flange steel beams strengthened by cover plate 12 mm thick one
at the top and one at the bottom. It is simply supported on a span of 9 m. each of the
cover-plated steel beam is subjected to the following loads:
DL = 12 kN/m (including self weight)
LL = 20 kN/m
Properties of W830x175
A = 11,500 mm^2 bf = 250 mm
d = 350 mm Ix = 266x10^6 mm^4
tw = 10 mm Iy = 45 x10^6 mm^4
tf = 16 mm Fy = 248 MPa
Calculate the required width of the cover plates to sustain the given loads if allowable
bending stress in tension and compression is 0.6Fy.
a. 150 mm
b. 180 mm
c. 200 mm
d. 250 mm
Question 27
Contributed by: System Admin
The floor system of a building consists of ribbed metal deck with 50 mm concrete slab on top.
The deck is supported by wide flange steel beams strengthened by cover plate 12 mm thick one
at the top and one at the bottom. It is simply supported on a span of 9 m. each of the
cover-plated steel beam is subjected to the following loads:
DL = 12 kN/m (including self weight)
LL = 20 kN/m
Properties of W830x175
A = 11,500 mm^2 bf = 250 mm
d = 350 mm Ix = 266x10^6 mm^4
tw = 10 mm Iy = 45 x10^6 mm^4
tf = 16 mm Fy = 248 MPa
Calculate the location of cut off point of the cover plates from the left support. Back
a 3 12 m
https://inhinyero.ph/exam/question 11/30
5/4/2020 Exam | Inhinyero - Student Portal
a. 3.12 m
b. 2.75 m
c. 2.33 m
d. 1.95 m
Question 28
Contributed by: System Admin
A W21 x 62 beam (Fy = 248 MPa) is resting on a concrete wall, f’c = 21 MPa. The end reaction
due to dead load is 116 kN and due to live load is 191 kN. Section properties are d = 525
mm, bf = 210 mm, tw = 10 mm, tf = 15 mm and k = 28 mm.
Calculate the required length of bearing plate so that web yield stress will not exceed
0.66Fy
a. 100 mm
b. 120 mm
c. 150 mm
d. 170 mm
Question 29
Contributed by: System Admin
A W21 x 62 beam (Fy = 248 MPa) is resting on a concrete wall, f’c = 21 MPa. The end reaction
due to dead load is 116 kN and due to live load is 191 kN. Section properties are d = 525
mm, bf = 210 mm, tw = 10 mm, tf = 15 mm and k = 28 mm.
Calculate the most economical width of the bearing plate if the concrete wall support is 200
mm thick.
a. 320 mm
b. 350 mm
c. 300 mm
d. 210 mm
Question 30
Contributed by: System Admin
A W21 x 62 beam (Fy = 248 MPa) is resting on a concrete wall, f’c = 21 MPa. The end reaction
due to dead load is 116 kN and due to live load is 191 kN. Section properties are d = 525
mm, bf = 210 mm, tw = 10 mm, tf = 15 mm and k = 28 mm.
Calculate the required thickness of the bearing plate if allowable bending stress is 0.75Fy.
Use Fy = 345 MPa for the bearing plate.
a. 42.8 mm
b. 44.8 mm
c. 47.4 mm
Back
d. 40.2 mm
https://inhinyero.ph/exam/question 12/30
5/4/2020 Exam | Inhinyero - Student Portal
Question 31
Contributed by: System Admin
A W21 x 62 beam (Fy = 345 MPa) is resting on a concrete wall, f’c = 21 MPa. The dead load is
116 kN and the live load is 191 kN. Section properties are d = 525 mm, bf = 210 mm, tw = 10
mm, tf = 15 mm and k = 28 mm
Calculate the required thickness of the concrete wall support so that bearing stress on
concrete will not exceed 0.35f’c.
a. 165 mm
b. 180 mm
c. 200 mm
d. 210 mm
Question 32
Contributed by: System Admin
A W21 x 62 beam (Fy = 345 MPa) is resting on a concrete wall, f’c = 21 MPa. The dead load is
116 kN and the live load is 191 kN. Section properties are d = 525 mm, bf = 210 mm, tw = 10
mm, tf = 15 mm and k = 28 mm
Calculate the required thickness of the concrete wall support so that web crippling will be
prevented.
Image:
a. 165 mm
b. 180 mm
c. 200 mm
d. 210 mm
Question 33
Contributed by: Encoder 2
A W21 x 62 beam (Fy = 345 MPa) is resting on a concrete wall, f’c = 21 MPa. The dead load is
116 kN and the live load is 191 kN. Section properties are d = 525 mm, bf = 210 mm, tw = 10
mm, tf = 15 mm and k = 28 mm
Calculate the required thickness of the concrete wall support so that bearing plate is not
required.
a. 200 mm
b. 225 mm
c. 400 mm
Back
d. 450 mm
https://inhinyero.ph/exam/question 13/30
5/4/2020 Exam | Inhinyero - Student Portal
Question 34
Contributed by: Encoder 2
Image:
a. 311
b. 280
c. 622
d. 560
Question 35
Contributed by: Encoder 2
Image:
a. 334
b. 376
c. 418
Back
d. 460
https://inhinyero.ph/exam/question 14/30
5/4/2020 Exam | Inhinyero - Student Portal
Question 36
Contributed by: Encoder 2
Image:
a. 406
b. 385
c. 257
d. 227
Question 37
Contributed by: Encoder 2
Image:
A. 1000 N-m
B. 800 N-m
C. 1200 N-m
D. 1400 N-m
,
Back
Question 38
Contributed by: Encoder 2
https://inhinyero.ph/exam/question 15/30
5/4/2020 Exam | Inhinyero - Student Portal
Image:
A. 800 N
B. 600 N
C. 1000 N
D. 500 N
Question 39
Contributed by: Encoder 2
Given a space truss in figure SDC-03 Determine the force in the member of the space truss.
Indicate if the members are in tension or compression.
The force in member BD
Image:
A. 0 kN
B. 2 kN (T)
C. 2 kN (C)
D. 4 kN (T)
Question 40
Contributed by: Encoder 2
Given a space truss in figure SDC-03 Determine the force in the member of the space truss.
Indicate if the members are in tension or compression.
Back
The force in member AB
https://inhinyero.ph/exam/question 16/30
5/4/2020 Exam | Inhinyero - Student Portal
Image:
A. 0 kN
B. 2 kN (T)
C. 2 kN (C)
D. 4 kN (T)
Question 41
Contributed by: Encoder 2
Given a space truss in figure SDC-03 Determine the force in the member of the space truss.
Indicate if the members are in tension or compression.
The force in member AE
Image:
A. 0 kN
B. 2 kN (T)
C. 2 kN (C)
D. 4 kN (T)
Question 42
Contributed by: Encoder 2
and-socket joint A?
https://inhinyero.ph/exam/question 17/30
5/4/2020 Exam | Inhinyero - Student Portal
The reaction at A.
A. 1460.50 kN
B. 1632.91 kN
C. 2065.52 kN
D. 2091.25 kN
Question 43
Contributed by: Encoder 2
Image:
A. 1460.59
B. 1306.39 kN
C. 730.30 kN
D. 653 kN
Question 44
Contributed by: Encoder 2
A 4-m tapered steel column has a diameter at the top of 300mm and 500mm at the bottom. It is
subjected at a compressive force of 20,000 kN.
Determine the stress at a point 1m from the top.
A. 211.89 MPa
B. 159.15 MPa
C. 189.41 MPa
D. 207.86 MPa
Back
,
https://inhinyero.ph/exam/question 18/30
5/4/2020 Exam | Inhinyero - Student Portal
Question 45
Contributed by: Encoder 2
A 4-m tapered steel column has a diameter at the top of 300mm and 500mm at the bottom. It is
subjected at a compressive force of 20,000 kN.
Determine how much the shortening of the column is.
A. 1.92 mm
B. 3.79 mm
C. 3.40 mm
D. 1.63 mm
Question 46
Contributed by: Encoder 2
A 7KN Load will fall in the midspan from a height of 0.4m in a 10m simply supported beam
assume EI = 400 x 1010 N.mm2.
Which of the following most nearly gives the maximum midspan moment?
Image:
A. 277.05 kN.m
B. 151.78 kN.m
C. 163.82 kN.m
D. 288.82 kN.m
Question 47
Contributed by: Encoder 2
A 7KN Load will fall in the midspan from a height of 0.4m in a 10m simply supported beam
assume EI = 400 x 1010 N.mm2.
Which of the following most nearly gives the maximum midspan deflection?
Image:
Back
https://inhinyero.ph/exam/question 19/30
5/4/2020 Exam | Inhinyero - Student Portal
A. 425.67 mm
B. 373.85 mm
C. 356.72 mm
D. 402.98 mm
Question 48
Contributed by: Encoder 2
A 450 mm long plain concrete prism is subjected to the concentrated vertical loads as shown
in the figure. Cross section of the prism is given as 150 mm × 150 mm. Considering linear
stress distribution across the cross-section, the modulus of rupture (expressed in MPa) is:
Image:
a. 4.4 MPa
b. 3.0
c. 7.5
d. 2.7
Question 49
Contributed by: Encoder 2
An elevator weighing 9.8 kN starting from rest at the ground floor accelerates uniformly
attaining a speed of 144 m/min after travelling 5 m.
1. Give the acceleration of the elevator.
a. 1.47 m/s^2
b. 0.68
c. 0.55
d. 0.58
Question 50
Contributed by: Encoder 2
Image:
Back
https://inhinyero.ph/exam/question 20/30
5/4/2020 Exam | Inhinyero - Student Portal
a. 3.1285 kN
b. 4.1795
c. 2.8125
d. 1.2835
Question 51
Contributed by: Encoder 2
Image:
a. 7.50 kN
b. 5
c. 9.125
d. 8.5
Question 52
Contributed by: Encoder 2
Image:
a. 11.25 kN
b. 16
c. 9.75
d . 13
Back
,
https://inhinyero.ph/exam/question 21/30
5/4/2020 Exam | Inhinyero - Student Portal
,
Question 53
Contributed by: Encoder 2
a. Attics
b. Concrete Piping
c. Roof Drainage
d. Flashing
Question 54
Contributed by: Encoder 2
a. Skylights
b. Venetian blinds
c. Curtains
d. Mirrors
Question 55
Contributed by: Encoder 2
a. Condominiums
b. Nipa huts
c. Hotels
d. Offices
Question 56
Contributed by: Encoder 2
a. Condominiums
b. Nipa huts
c. Hotels
d. Offices
Back
https://inhinyero.ph/exam/question 22/30
5/4/2020 Exam | Inhinyero - Student Portal
,
Question 57
Contributed by: Encoder 2
Two structural members B and C are bolted to bracket A. Knowing that both members are in
tension and that P = 10 kN and Q = 15 kN, determine the angle of the resultant force exerted
on the bracket.
Image:
a. 15.5°
b. 21.2°
c. 27.8°
d. 33.6°
Question 58
Contributed by: Encoder 2
Image:
a. -0.005
b. -0.004
c. -0.01
d. 0.017
Question 59
Contributed by: Encoder 2
A 9 m high retaining wall is laterally supported at the top and fixed at the base. The wall
resists active earth pressure increasing from zero at the top to 52 kN/m at the base per
square meter length along the longitudinal axis.
Determine the resulting base shear if the wall is free at the top. Back
https://inhinyero.ph/exam/question 23/30
5/4/2020 Exam | Inhinyero - Student Portal
a. 189 kN
b. 234
c. 317
d. 405
Question 60
Contributed by: Encoder 2
A 9 m high retaining wall is laterally supported at the top and fixed at the base. The wall
resists active earth pressure increasing from zero at the top to 52 kN/m at the base per
square meter length along the longitudinal axis.
Determine the design moment at the base if the lateral support at the top of the wall was
removed.
a. 702 kN m
b. 957.1
c. 1005.8
d. 1123.6
Question 61
Contributed by: Encoder 2
A 9 m high retaining wall is laterally supported at the top and fixed at the base. The wall
resists active earth pressure increasing from zero at the top to 52 kN/m at the base per
square meter length along the longitudinal axis.
Determine the design moment at the base.
a. -227.9 kN. m
b. -252.9
c. -280.8
d. 256.1
Question 62
Contributed by: System Admin
The NSCP 2015 (ACI Code) specifies two methods for designing two-way slabs for gravity loads.
These are direct design method and equivalent frame method. Assume all conditions and
limitations are satisfied. The slab is to support a live load of 6kpa and a dead load of 4.8
kPa including the slab weight. The slab is supported by beams along the column line with
cross sections shown. Design all moments in the short-span direction centered on interior
column line.
Given:
All columns are 375x375 mm
f’c = 3000 psi Back
fy = 60,000 psi
https://inhinyero.ph/exam/question 24/30
5/4/2020 Exam | Inhinyero - Student Portal
U = 1.2DL + 1.6 LL
Slab thickness = 150 mm
Use:
I for edge beams = 5605.8048 x 10 ^6 mm^4
I for interior beams = 6568.548 x 10^6 mm^4
Use figure 2-5 for reference and chapter 408.10 of NSCP 2015
Using direct-design method, find the portion of interior positive moment to be resisted goes
to the middle strip slab moments of panel s1 as per NSCP 2015.
Image:
35.502
35.252
30.502
53.502
Question 63
Contributed by: System Admin
The NSCP 2015 (ACI Code) specifies two methods for designing two-way slabs for gravity loads.
These are direct design method and equivalent frame method. Assume all conditions and
limitations are satisfied. The slab is to support a live load of 6kpa and a dead load of 4.8
kPa including the slab weight. The slab is supported by beams along the column line with
cross sections shown. Design all moments in the short-span direction centered on interior
column line.
Given:
All columns are 375x375 mm
f’c = 3000 psi
fy = 60,000 psi
U = 1.2DL + 1.6 LL
Slab thickness = 150 mm
Use:
I for edge beams = 5605.8048 x 10 ^6 mm^4
I for interior beams = 6568.548 x 10^6 mm^4
Use figure 2-5 for reference and chapter 408.10 of NSCP 2015
Using direct-design method, find the portion of interior positive moment to be resisted by
column strip of panel s1 as per NSCP 2015 is allotted to slab.
a. 14.117kN-m
b. 11.474
c. 17.414
Back
d. 14.741
https://inhinyero.ph/exam/question 25/30
5/4/2020 Exam | Inhinyero - Student Portal
Question 64
Contributed by: System Admin
The NSCP 2015 (ACI Code) specifies two methods for designing two-way slabs for gravity loads.
These are direct design method and equivalent frame method. Assume all conditions and
limitations are satisfied. The slab is to support a live load of 6kpa and a dead load of 4.8
kPa including the slab weight. The slab is supported by beams along the column line with
cross sections shown. Design all moments in the short-span direction centered on interior
column line.
Given:
All columns are 375x375 mm
f’c = 3000 psi
fy = 60,000 psi
U = 1.2DL + 1.6 LL
Slab thickness = 150 mm
Use:
I for edge beams = 5605.8048 x 10 ^6 mm^4
I for interior beams = 6568.548 x 10^6 mm^4
Use figure 2-5 for reference and chapter 408.10 of NSCP 2015
Using direct-design method, find the portion of interior negative moment to be resisted by
column strip of panel s1 as per NSCP 2015.
a. 142.05kN-m
b. 124.50
c. 150.42
d. 105.24
Question 65
Contributed by: Encoder 2
The automobile shown in Figure 1, with center of gravity at G, is parked on an 18o slope with
its brakes off. Neglecting friction
which of the following most nearly gives the force given by the curb that will prevent the
automobile from rolling down the plane if the mass of the car is 1000kg
a. 1530 kg
b. 1120
c. 374
d. 655
Question 66
Contributed by: Encoder 2
The automobile shown in Figure 1, with center of gravity at G, is parked on an 18o slope withBack
its brakes off. Neglecting friction
https://inhinyero.ph/exam/question 26/30
5/4/2020 g g Exam | Inhinyero - Student Portal
determine the height h of the smallest curb that will prevent the automobile from rolling
down the plane
Image:
a. 29.57
b. 25.79
c. 25.97
d. 27.95
Question 67
Contributed by: Encoder 2
A water tank 3.4 m in diameter and 8 m high, is made from steel plates 12 mm thick
If the circumferential stress is limited to 10 MPa, what is the maximum height of water to
which the tank may be filled.
a. 6.2 m
b. 7.2 m
c. 5.8 m
d. 6.8 m
Question 68
Contributed by: Encoder 2
A water tank 3.4 m in diameter and 8 m high, is made from steel plates 12 mm thick
When the tank is full of water, calculate the longitudinal stress in MPa at the bottom of the
tank.
a. 7.68
b. 9.38
c. 5.56
d. 8.22
Question 69
Contributed by: Encoder 2
A water tank 3.4 m in diameter and 8 m high, is made from steel plates 12 mm thick
When the tank is full of water, calculate the circumferential stress in MPa in the tank.
Back
a. 11.12
https://inhinyero.ph/exam/question 27/30
5/4/2020 Exam | Inhinyero - Student Portal
b. 18.75
c. 15.36
d. 22.24
Question 70
Contributed by: Encoder 2
Floor joists 50 mm wide by 200 mm high, simply supported on a 4-m span, carry a floor loaded
at 5 kN/m^2
What safe floor load could be carried on a center-line spacing of 0.40 m?
a. 3.34 kPa
b. 4.58 kPa
c. 4.16 kPa
d. 2.31 kPa
Question 71
Contributed by: Encoder 2
Floor joists 50 mm wide by 200 mm high, simply supported on a 4-m span, carry a floor loaded
at 5 kN/m^2.
Compute the safe center-line spacing between joists.
a. 0.333 m
b. 0.367 m
c. 0.425 m
d. 0.267 m
Question 72
Contributed by: Encoder 2
Floor joists 50 mm wide by 200 mm high, simply supported on a 4-m span, carry a floor loaded
at 5 kN/m^2.
Compute the maximum bending moment, in kN m, a single floor joist could carry if the maximum
bending stress is limited to 8 MPa.
a. 3.33
b. 3.67
c. 4.25
d. 2.67
Question 73
Contributed by: Encoder 2
Back
A it
https://inhinyero.ph/exam/question
h ft i i i th f ll i fi R i AB i l i ll h i G 28/30
5/4/2020 Exam | Inhinyero - Student Portal
A composite shaft is given in the following figure. Region AB is aluminum alloy, having G =
28 GPa, and region BC is steel, having G = 84 GPa. The aluminum portion is of solid circular
cross section 45 mm in diameter, and the steel region is circular of 60 mm outside diameter
and 30 mm inside diameter. A torsional load of 4,000 N-m is applied at B. Ends A and C are
rigidly clamped.
Calculate the angle of twist at B.
Image:
a. 3.85°
b. 2.42°
c. 1.82°
d. 2.16°
Question 74
Contributed by: Encoder 2
A composite shaft is given in the following figure. Region AB is aluminum alloy, having G =
28 GPa, and region BC is steel, having G = 84 GPa. The aluminum portion is of solid circular
cross section 45 mm in diameter, and the steel region is circular of 60 mm outside diameter
and 30 mm inside diameter. A torsional load of 4,000 N-m is applied at B. Ends A and C are
rigidly clamped.
Calculate the peak shearing stress in region BC.
Image:
a. 79.4 MPa
b. 84.7 MPa
c. 80.2 MPa
d. 85.6 MPa
Question 75
Contributed by: Encoder 2
A composite shaft is given in the following figure. Region AB is aluminum alloy, having G =
28 GPa, and region BC is steel, having G = 84 GPa. The aluminum portion is of solid circular
cross section 45 mm in diameter, and the steel region is circular of 60 mm outside diameter
and 30 mm inside diameter. A torsional load of 4,000 N-m is applied at B. Ends A and C are
rigidly clamped. Back
1. Calculate TL.
https://inhinyero.ph/exam/question 29/30
5/4/2020 Exam | Inhinyero - Student Portal
Image:
a. 632 N•m
b. 3,368 N•m
c. 598 N•m
d. 3,402 N•m
Back
https://inhinyero.ph/exam/question 30/30