Professional Documents
Culture Documents
Vigas y Columnas
F x
0 M x
0
F y
0 M y
0
F z
0 M z
0
– Sistema co-planar:
F x
0
F 0
y
N
M O
0
Sistemas Estructurales Determinados:
“Statically Determinate”
Vigas (“Beams”)
Pórticos Articulados
(“Hinged frames”)
Structural Elements
Beam
Beam-Column
Determinate and Indeterminate Elements
1. Beams and Hinged Frames:
R – 3 N = 0; Determinate
R – 3 N > 0; Indeterminate (Degree of redundancy)
R – 3 N < 0; Unstable
1
R=3
N = 1; Determinate
2
R=6
N = 2; Determinate
Beam elements
R3
n 1
Cantilever
R 3n; 3 3
Determinate Beams
Vigas Estáticamente Indeterminadas
(Indeterminate beams)
Continuous Fix-Pin
Fix-Fix
Determine if the beams shown are:
a) Determinate
b) Indeterminate, Degree=1
c) Indeterminate, Degree=2
d) Unstable
A. Answer: d) Unstable
B. Answer: a) Determinate
3
A
B
20’ 5’
A. The resultant of the distributed force is most nearly
a) 12,000 lb
b) 4,000 lb
c) 6,000 lb
d) 600 lb
1 lb
SOLUTION: FR 600
2 ft
20ft 6,000lb
3
AY PY P 2K
5
3
1.2 K
5
D. The location (from support A) of the resultant distributed
force is most nearly
a) 12 ft
b) 13 ft
c) 15 ft
d) 10 ft
2
SOLUTION: X 20ft 13.3 ft
3
1.2
Ax
Ay By
13.34’ 5’
20’
M A 0
By 20' 6k 13.34' 1.6k 25' 0
By 2.00 kips
G. The vertical reaction at A is most nearly:
a) 1,200 lb
b) 1,400 lb
c) 2,200 lb 6
1.6
d) 2,400 lb
1.2
Ax
Ay By
13.34’ 5’
20’
F 0
y
2.00 kips
By 6k 1.6k Ay 0
Ay 2.40 kips
The frame shown is pin-supported at points A and C and is hinged at joint
B.
Solution: Since element BC is not externally loaded, reactions at B are the same
as C but in opposite sense.
175N
131.6N
131.6N
175N
Fuerzas Internas
Vigas:
Las Fuerzas Internas desarrolladas en vigas estáticamente
determinadas no dependen de las propiedades
seccionales del elemento de viga.
Sección de Sección de
viga de viga de
acero hormigón
Fuerzas Internas en Vigas (“Internal
Forces in Beams”)
P
Comp.
Tens.
- V
M
-
V
Fuerzas Internas en elementos de Vigas
Axial
Positivo: Tensión
Negativo: Compresión.
N N
+
N
- N
Fuerzas Internas en Pórticos Determinados
Procedimiento
1. Hallar las reacciones del sistema.
Segmentos críticos:
Un segmento crítico está descrito por el tramo de
la viga entre dos puntos críticos. En cada corte
se hallará una ecuación de cortante y otra de
momento. El total de cortes dependerá del total
de segmentos críticos existentes en la viga.
Ecuaciones de Cortante y Momento
Ptos. críticos: A, B, C, D, E
Segmentos críticos: A-B, B-C, C-D y D-E
Total de cortes a realizar: 4 para hallar
fuerzas internas V(x) y M(x) a lo largo de
toda la viga
Ecuaciones de Cortante y Momento
C. Hacer diagrama de cuerpo libre de izquierda a
derecha o de derecha a izquierda según convenga.
Localizar e indicar las fuerzas internas desconocidas (V,
M, N) con la convención de signos positiva definida
anteriormente.
P
SOLUTION:
20’ 5’
F’R
wcut 600 lb/ft F 0
y
2.4 k
Ax Ay F' R V 0
Ay
V V 2.4 1.5 0.9 kips
10’
20’
Moment at this point?
19 k-ft
w cut w 10' 600 lb / ft
w cut 300 lb / ft
10' 20' 20'
1 1
F' R w cut 10' 300 lb / ft 10' 1500 lb
2 2
The 20 ft beam carries an uniformly distributed load of 350 lbf/ft
ending at the midspan of the beam. Measured from the left-
support, the point at which the shear is zero is most nearly:
a) 0.87 ft
b) 4.1 ft
c) 8 ft
d) 14 ft
SOLUTION:
10 ft
M A 0:
Shear Diagram:
2,625
2,625 - FR
=2,625 - 3,500 = -875 875
Similar triangles:
2,625
0 0
-875
10 ft 10 ft
10ft X
2,625 875 2,625
X 7.5 ft
35
SUPERPOSITION OF DIAGRAMS
Pelé
60