Professional Documents
Culture Documents
Calculation Note - 1710-EQ20V
Calculation Note - 1710-EQ20V
Calculation note
Calculation model
With reference to the document “4124-CD-DX-21700V020-IS01”, here below the loads on foundation:
APPLIED LOADS
17-V-020
17-V-020
1 0.9Dead + 0.9DS + 0.9DE + 0.9DO + 1.4Wx 342.90 28.00 161.00 0.00 0.00
2 0.9Dead + 0.9DS + 0.9DE + 0.9DO + 1.4Wy 342.90 0.00 0.00 28.00 161.00
3 1.05Dead + 1.05DS + 1.05DE + DO + 1.4Wx 400.05 28.00 161.00 0.00 0.00
4 1.05Dead + 1.05DS + 1.05DE + DO + 1.4Wy 400.05 0.00 0.00 28.00 161.00
5 0.9Dead + 0.9DS + 0.9DE + 0.8DO 342.90 0.00 0.00 0.00 0.00
6 0.9Dead + 0.9DS + 0.9DE + 1.12Wx 342.90 22.40 128.80 0.00 0.00
7 0.9Dead + 0.9DS + 0.9DE + 1.12Wy 342.90 0.00 0.00 22.40 128.80
8 1.05Dead + 1.05DS + 1.05DE + DT + 0.98Wx 797.05 19.60 112.70 0.00 0.00
9 1.05Dead + 1.05DS + 1.05DE + DT + 0.98Wy 797.05 0.00 0.00 19.60 112.70
10 0.9Dead + 0.9DS + 0.9DE 342.90 0.00 0.00 0.00 0.00
11 1.05Dead + 1.05DS + 1.05DE 400.05 0.00 0.00 0.00 0.00
BEARING CAPACITY - REDUCED EFFECTIVE AREA METHOD
1 0.9Dead + 0.9DS + 0.9DE + 0.9DO + 1.4Wx 83.55 814.00 0.00 25.66 223.97 0.00
Buoy 74.19 794.33 0.00 29.70 223.97 0.00
2 0.9Dead + 0.9DS + 0.9DE + 0.9DO + 1.4Wy 83.55 814.00 25.66 0.00 0.00 223.97
Buoy 74.19 794.33 29.70 0.00 0.00 223.97
3 1.05Dead + 1.05DS + 1.05DE + DO + 1.4Wx 95.14 814.00 0.00 21.99 223.97 0.00
Buoy 84.10 794.33 0.00 25.46 223.97 0.00
4 1.05Dead + 1.05DS + 1.05DE + DO + 1.4Wy 95.14 814.00 21.99 0.00 0.00 223.97
Buoy 84.10 794.33 25.46 0.00 0.00 223.97
5 0.9Dead + 0.9DS + 0.9DE + 0.8DO 71.30 814.00 0.00 0.00 0.00 0.00
Buoy 61.60 794.33 0.00 0.00 0.00 0.00
6 0.9Dead + 0.9DS + 0.9DE + 1.12Wx 80.77 814.00 0.00 20.53 179.18 0.00
Buoy 71.28 794.33 0.00 23.76 179.18 0.00
7 0.9Dead + 0.9DS + 0.9DE + 1.12Wy 80.77 814.00 20.53 0.00 0.00 179.18
Buoy 71.28 794.33 23.76 0.00 0.00 179.18
8 1.05Dead + 1.05DS + 1.05DE + DT + 0.98Wx 123.42 814.00 0.00 11.08 156.78 0.00
Buoy 112.16 794.33 0.00 12.28 156.78 0.00
9 1.05Dead + 1.05DS + 1.05DE + DT + 0.98Wy 123.42 814.00 11.08 0.00 0.00 156.78
Buoy 112.16 794.33 12.28 0.00 0.00 156.78
10 0.9Dead + 0.9DS + 0.9DE 71.30 814.00 0.00 0.00 0.00 0.00
Buoy 61.60 794.33 0.00 0.00 0.00 0.00
11 1.05Dead + 1.05DS + 1.05DE 83.18 814.00 0.00 0.00 0.00 0.00
Buoy 71.86 794.33 0.00 0.00 0.00 0.00
In following table are shown the bearing capacity calculated whit Meyerhof method:
1 0.9Dead + 0.9DS + 0.9DE + 0.9DO + 1.4Wx 100.00 6.82 1.50 100.00 12.47 1.50
Buoy 100.00 5.79 1.50 100.00 10.77 1.50
2 0.9Dead + 0.9DS + 0.9DE + 0.9DO + 1.4Wy 6.82 100.00 1.50 12.47 100.00 1.50
Buoy 5.79 100.00 1.50 10.77 100.00 1.50
3 1.05Dead + 1.05DS + 1.05DE + DO + 1.4Wx 100.00 7.96 1.50 100.00 14.55 1.50
Buoy 100.00 6.92 1.50 100.00 12.57 1.50
4 1.05Dead + 1.05DS + 1.05DE + DO + 1.4Wy 7.96 100.00 1.50 14.55 100.00 1.50
Buoy 6.92 100.00 1.50 12.57 100.00 1.50
5 0.9Dead + 0.9DS + 0.9DE + 0.8DO 100.00 100.00 1.50 100.00 100.00 1.50
Buoy 100.00 100.00 1.50 100.00 100.00 1.50
6 0.9Dead + 0.9DS + 0.9DE + 1.12Wx 100.00 8.52 1.50 100.00 15.59 1.50
Buoy 100.00 7.24 1.50 100.00 13.47 1.50
7 0.9Dead + 0.9DS + 0.9DE + 1.12Wy 8.52 100.00 1.50 15.59 100.00 1.50
Buoy 7.24 100.00 1.50 13.47 100.00 1.50
8 1.05Dead + 1.05DS + 1.05DE + DT + 0.98Wx 100.00 15.80 1.50 100.00 28.89 1.50
Buoy 100.00 14.32 1.50 100.00 26.06 1.50
9 1.05Dead + 1.05DS + 1.05DE + DT + 0.98Wy 15.80 100.00 1.50 28.89 100.00 1.50
Buoy 14.32 100.00 1.50 26.06 100.00 1.50
10 0.9Dead + 0.9DS + 0.9DE 100.00 100.00 1.50 100.00 100.00 1.50
Buoy 100.00 100.00 1.50 100.00 100.00 1.50
11 1.05Dead + 1.05DS + 1.05DE 100.00 100.00 1.50 100.00 100.00 1.50
Buoy 100.00 100.00 1.50 100.00 100.00 1.50
Top Steel
Bottom Steel
17-V-020
Top Steel
Bottom Steel
Member length 1 m
Effective length factor in the XoY plane 1
Effective length factor in the XoZ plane 1
Random eccentricity along Z according to SNiP 52-01-2003 (Russia)
Random eccentricity along Y according to SNiP 52-01-2003 (Russia)
Structure is statically determinate
Limit slenderness - 200
Section
500 Z 500
300
600
300
1000
b = 1000 mm
h = 600 mm
a1 = 50 mm
a2 = 50 mm S1 - 520
S2 - 520
Transverse reinforcement along axis Y 220,
spacing of transverce reinforcement 200 mm
Concrete
Concrete type: Heavy-weight
Concrete grade: B40
Service factor for concrete
b1 allowance for the sustained loads 0.9
b2 allowance for the failure behavior 1
b3 allowance for the vertical position during concreting 1
b4 allowance for the freezing/thawing and negative temperatures 1
Humidity of environment air - 40-75%
Crack Resistance
Limited crack opening width
Requirements to crack opening width are based on the limitation of the structural permeability
Allowable crack opening width:
Short-term opening 0.3 mm
Long-term opening 0.2 mm
N My Qz Mz Qy T Short-
Seismicity
kN kN*m kN kN*m kN kN*m term
1 Design 0 14 0 0 0 0
Design long-term 0 0 0 0 0 0
Characteristic 0 10 0 0 0 0
Characteristic 0 0 0 0 0 0
long-term
Utilization factor over all package of combinations 0.047 - Ultimate moment strength of the section
CHECK FOR (TENSION) BREAKOUT REINFORCEMENT - AS PER 4018-AX-SG-G0000002-IS0.
Pedestal-Anchor bolt type
Description legends (as per AADC drg) units
BP3
Anchor Bolt Diameter ∅ bolt 1 in
Lx 138 in
Pedestal size (from AADC drawing)
Lz 138 in
Clear cover to pedestal from Top of concrete
c 2 in
(as per 4018-AA-DX-G00000001)
shear key provided - no
Influence radius to be considered for breakout
mechanism for TENSION in anchor bolts.(as per q 9 1/8 #N/D #N/D in
table-3 of 4018-AX-SG-G00000002)
Distance of farthest vertical bar in pedestal from
qact 5 6/8 in
bolt center (as per AADC drawing)
Number of vertical rebars considered within
n 6 -
actual influence radius for each bolt
Diameter of vertical rebar in pedestal ∅ rebar 7/8 in
Embeded length of anchor bolts (20*∅bolt) Lbolt 20 #N/D #N/D in
Required lap length between anchor bolt and
vertical rebar Ldreq 40 #N/D #N/D in
(as per table-4 of 4018-AX-SG-G00000002)
Lap length between embeded length of anchor
bolt and farthest vertical rebar of column Ldact 14.17 #N/D #N/D in
Ldact = Lbolt - c - {qact*tan(33.7)}
Efficiency of lap length (Ld act / Ldreq) η 0.35 #N/D #N/D -
Area of tension reinforcement required for each
Astreqd 0.59 #N/D #N/D in2
bolt (as per table-3 of 4018-AX-SG-G00000002)
Area of tension reinforcement provided
Astprov. 1.28 #N/D #N/D in2
Astprov. = 0.785*∅rebar2*η
Additional area of tension reinforcement
required (such as hairpin reinforcement) Astextra 0.00 #N/D #N/D in2
Astextra = Astreqd - Astprov.
Assumed diameter of hairpin reinforcement ∅ hairpin 0 in
Number of legs of Hairpin reinforcement
r 0.00 -
effective for each anchor bolt.
Effective area contribition of hairpin
reinforcement to each anchor bolt Asthairpin 0.00 #N/D #N/D in2
Asthairpin = 0.785*∅hairpin2*η*r
TOTAL Area of tension reinforcement provided
AstTotal 1.28 #N/D #N/D in2
AstTotal = Astprov. + Asthairpin
check for Total tension breakout reinforcement
OK #N/D #N/D
provided (Asttotal v/s Astreqd)
CHECK FOR (SHEAR) BREAKOUT REINFORCEMENT - AS PER 4018-AX-SG-G0000002-IS0.
PEDESTAL-
Description legends ANCHOR BOLT units
BP3 0
Shear key provided - no -
Anchor Bolt Diameter ∅ bolt 1 0 0 in
Number of bolts effective in shear breakout nbolt 12 -
Influence depth to be considered for breakout
mechanism for SHEAR in anchor bolts. w 8 #N/D #N/D in
(as per table-3 of 4018-AX-SG-G00000002)
Number layers of shear R/F present in influence
n 4 -
depth defined above
Minimum number of stirrup legs effective in
legs 8 -
shear resistance
Diameter of shear reinforcement ∅ shear 3/8 in
Area of shear reinforcement required for each
Asvreqd 0.25 #N/D #N/D in2
bolt (as per table-3 of 4018-AX-SG-G00000002)
Area of Shear reinforcement provided
Asvprov 0.33 #DIV/0! #DIV/0! in2
Asvprov. = n*legs*(0.785*∅shear2)/nbolt
check for Total shear breakout reinforcement
OK #DIV/0! #DIV/0!
(Asvprov v/s Asvreqd)