Professional Documents
Culture Documents
Holistic Academy-Test-RCC Q-Paper
Holistic Academy-Test-RCC Q-Paper
a) 0.5 b) 1 c) 2 d) 3
3. Maximum permissible limit for sulphate concentration (in mg/l) in water to be used for RCC
construction as per IS 456 : 2000 is
4. Consider the following assumptions used for the designing limit state in flexure.
1. Plane sections normal to the axis of bending remain plane after bending.
2. The maximum strain in concrete at the outermost compression edge is taken as 0.0035 in
bending.
3. The relation between compressive stress distribution and the corresponding compressive strain is
assumed to be rectangular only.
Which of the above assumptions are correct as per IS 467 : 2000?
5. If mild steel bars are replaced by HYSD bars, then the bond strength will
6. In case of flexural tension or flexural compression, the minimum length of the bar which must be
embedded in concrete beyond any section to develop its full strength is termed as
a) 1.05 times the load carried by the similar column with ties.
b) 2.15 times the load carried by the similar column with ties.
c) 1.15 times the load carried by the similar column with ties.
d) 2.05 times the load carried by the similar column with ties.
9. The maximum compressive strain in concrete in a balanced failure of a short column subjected to
axial load P and bending moment M due to eccentricity is [ Loading eccentricity is sufficiently high]
a) 0.0020
b) 0.0035 minus 0.75 times the strain at the least compressed extreme fibre
c) 0.0035
d) None of the above
10. A slab simply supported on all four sides has dimensions 8 m x 3 m. The type of reinforcement
provided along 8 m length is
11. For a pretensioned beam, young’s modulus of steel and concrete are 200 GPa and 35 GPa
respectively. If ultimate shrinkage strain and ultimate creep coefficient are 200 microns and 1.6
respectively, what is the level of sustained stress (in MPa) in concrete at level of steel if the loss due
to creep is 3 times the loss due to shrinkage.
a) 9 b) 13 c) 17 d) 15
12. When the reaction in the direction of the applied shear introduces compression into the end
region of the member, sections located at a distance less than ___________ x d from the face of
support may be designed for the same shear as that computed at distance d. [Where d is effective
depth of the beam ]
a) 1 b) 0.5 c) 1.5 d) 2
13. To prevent cracking of edges, the corners in two way slab are provided with
14. Critical section for two way shear in case of isolated footing design at
15. Strength of concrete is found to decrease with increase in the size of specimen. However
beyond 450 mm there is no decrease in the compressive strength of concrete. Hence in concrete
structures the compressive strength of concrete is taken as ___________x 𝑓𝑐𝑘 .[where 𝑓𝑐𝑘 is the
characteristic strength of concrete]
18. Side face reinforcement shall be provided in the beam when depth of the web in a beam exceeds
19. When HYSD bars are used in place of mild steel bars in a beam?
a) Both bond strength and ductility increase c) Bond strength increases and ductility decreases
b) Both bond strength and ductility decrease d) Bond strength decreases and ductility increases
20. As compared to WSM, LSM used for design of beam section will have
21. If a simply supported post – tensioned beam of span ‘L’ is pre – stressed by a straight tendon at a
uniform eccentricity ‘e’ below the centroidal axis and a pre – stressing force ‘P’ with flexural rigidity
of beam as EI, then the maximum central deflection of the beam is
22. For a beam of span 13 m, the minimum effective depth (in mm) to satisfy the vertical direction
limit should be
23. Percentage of reinforcement in both directions of mild steel reinforcement in slab shall not be
less than
24. Accepted relationship between tread and riser in case of staircase design is
28. Which one of the following statements is the disadvantage of post – tensioning method?
29. A reinforced concrete circular section of 50,000 𝑚𝑚2 cross –sectional area carries 6 reinforcing
bars whose total area is 500 𝑚𝑚2 . If the concrete is not to be stressed more than 3.5 MPa and
modular ratio of steel and concrete is 18, the safe load the column can carry will be nearly
30. In a post – tension pre – stressed concrete beam, the end block zone is in between the end of
the beam and the section where
31.For a certain set of external loads, concordant profile in a prestressed beam represents to some
scale the
33. Spalling stresses are produced in post tensioned pre stressed concrete members at
35. A rectangular beam with b = 200 mm and effective depth d = 300 mm is subjected to limit state
shear of 80 kN and torsional moment of 6 kNm. The equivalent value of shear will be
36. A simply supported RC beam carries UDL and is referred to as beam A. A similar beam is
prestressed and carries the same UDL as the beam A. This beam is referred to as beam B. The mid –
span deflection of beam A will be
39. The minimum strain at failure in the tensile reinforcement (fy = 400 MPa) of RCC beam as per
limit state method is
40. A simply supported beam is considered as a deep beam if the ratio of effective span to overall
depth is less than
a) 1 b) 2 c) 1.5 d) 2.5
41. Which of the following are the desirable properties for efficient functioning in design for
movement joint of water tank?
1. The joint should accommodate repeated movement of the structure without loss of water
tightness.
2. The design should provide for exclusion of grit and debris which would prevent the closing of the
joint.
3. The material used in the construction of movement joints should not slump unduly in hot weather
or become brittle in cold weather.
42. The distance between the centroid of the area of tension reinforcement and the maximum
compressive fibre in a reinforced concrete beam design is known as
43. A simply supported beam having 200 mm width and 450 mm effective depth supports a total
uniformly distributed load of 200000 N. The nominal shear stress will be nearly.
44. In limit state design of concrete for flexure, the area of stress block is taken as
47. A reinforced concrete cantilever porch has thickness t. The main reinforcement steel will be
placed
48. A beam of size 250 mm width and 460 mm effective depth is subjected to limit state moment of
146 kNm. If M20 grade concrete and Fe415 steel are used the area of steel required will be
49. As per IS – 456: 2000, the value of maximum compression strain in concrete in axial compression
for limit state of collapse is
50. The positive bending moment coefficient at the middle of the end span of a continuous one way
slab is
𝑊 𝑊𝑑 𝑊 𝑊𝑑 𝑊 𝑊𝑑 𝑊 𝑊𝑑
a) ( 10𝑙 + 12
) 𝐿2 b) ( 9 𝑙 + 10
) 𝐿2 c) ( 12𝑙 + 16
) 𝐿2 d) ( 9 𝑙 + 12
) 𝐿2