Professional Documents
Culture Documents
Service Manual
KLINOSKOP H
MED
Siemens Ltd.
Copyright © SIEMENS LTD. INDIA. All rights reserved.
The information in this CD is not a controlled document and to be used only for reference.
Before ordering any parts HO-Med-CS-SP to be contacted for obtaining the latest information.
Back
S KLINOSKOP H
Main Index
KLINOSKOP H
4W 5245 0420723001
1. Pre - Installation
2. Installation
3. Circuit Diagram
4. Circuit Description
6. Spare Parts
Siemens Ltd.
Copyright © SIEMENS LTD. INDIA. All rights reserved.
The information in this CD is not a controlled document and to be used only for reference.
Before ordering any parts HO-Med-CS-SP to be contacted for obtaining the latest information.
Back
S KLINOSKOP H
Pre - Installation
KLINOSKOP H
MED
Siemens Ltd.
Copyright © SIEMENS LTD. INDIA. All rights reserved.
The information in this CD is not a controlled document and to be used only for reference.
Before ordering any parts HO-Med-CS-SP to be contacted for obtaining the latest information.
Back
S KLINOSKOP H
Pre - Installation
List of Pages
010 - 1 Pg. 1 / 1
Siemens Ltd.
Copyright © SIEMENS LTD. INDIA. All rights reserved.
The information in this CD is not a controlled document and to be used only for reference.
Before ordering any parts HO-Med-CS-SP to be contacted for obtaining the latest information.
Back
S KLINOSKOP H
Pre - Installation
Typical Layout Of X Ray room
4
950 mm
12
N
Y
3
CONTROL
6
E
P
O
8
11
A
7
D
5
9
2
C
1
B M
X
010 - 2 Pg. 1 / 2
Siemens Ltd.
Copyright © SIEMENS LTD. INDIA. All rights reserved.
The information in this CD is not a controlled document and to be used only for reference.
Before ordering any parts HO-Med-CS-SP to be contacted for obtaining the latest information.
Back
S KLINOSKOP H
Pre - Installation
A = 5030 mm ( 16 ‘ - 6 “ )
B = 4270 mm ( 14 ‘ - 0 “ )
C = 2370 mm ( 7 ‘ - 9 “ )
D = 1220 mm ( 4 ‘ - 0 “ )_
E = 1980 mm ( 6 ‘ - 6 “ )
010 - 2 Pg. 2 / 2
Siemens Ltd.
Copyright © SIEMENS LTD. INDIA. All rights reserved.
The information in this CD is not a controlled document and to be used only for reference.
Before ordering any parts HO-Med-CS-SP to be contacted for obtaining the latest information.
Back
S KLINOSKOP H
Pre - Installation
Schematic Layout
E RSTN
ELECTRIC ELECTRICAL
MOTOR WIRING
FOR
X-RAY
MACHINES
EARTH
WIRE
12
S.W.G.BARE
COPPER
MAINS
SWITCH
FUSE
UNIT(1)
EARTH
WIRE
12
S.W.G.BARE NO
COPPER PUSH
BUTTON
STATION(3)
MAINS NC
CONTACTOR(2)
EARTH
WIRE
12
S.W.G.BARE
COPPER
EARTH
WIRE
12
S.W.G.BARE
COPPER
010- 3 Pg. 1 / 2
Siemens Ltd.
Copyright © SIEMENS LTD. INDIA. All rights reserved.
The information in this CD is not a controlled document and to be used only for reference.
Before ordering any parts HO-Med-CS-SP to be contacted for obtaining the latest information.
Back
S KLINOSKOP H
Pre - Installation
Sr. Generator Power Line Power Mains Switch Mains Contactor Push button Mains Wire Size Earth
mA in Use Requirement Capacity Requirement Requirement station SWG or Sq. Mm Wire Size
requirement in Copper
1 300 mA 415 V , 50 Hz 40 KVA Siemens Make Siemens make Siemens make 7/16 or 10 12 SWG
Phase to Power Guard SICOP Power Push Button Bare
Phase Fuse Switch Unit Contactor of 63 Station Type copper
type 3KL5037 - A 3TF47 O2- 3SBO8 O2-8AC
1YA100 with HRC OA..ZAO1 with or Equivalent
Fuse type two “SIGUT” No.
3NA1018 of 63 A 3TX7 460-OE or
or Equivalent Equivalent
2 500 mA Same as above 65 KVA Same as above Same as above Same as above 19/18 or 12 Same as
above
3 800 mA Same as above 100 KVA Siemens Make Siemens make Same as above 19/18 or 25 Same as
Power Guard SICOP Power above
Fuse Switch Unit Contactor of 110
type 3KL5237 - A 3TF50 O2-
1YA100 with HRC OA..ZAO1 with
Fuse type two “SIGUT” No.
3NA1010 of 125 A 3TX7 460-OE or
or Equivalent Equivalent
Siemens Ltd.
Copyright © SIEMENS LTD. INDIA. All rights reserved.
The information in this CD is not a controlled document and to be used only for reference.
Before ordering any parts HO-Med-CS-SP to be contacted for obtaining the latest information.
Back
S KLINOSKOP H
Pre - Installation
General Guidelines
1 All the wall of the X - Ray examination room will have to be 9 inches (230 mm) thick for radiation
safety.. If the walls are of 4.5 inches ( 114 mm ) thickness , they will have to be plastered with
barium sulphate mixed with cement in proportion of 5 : 1 ( 5 parts of cement : 1 part of barium
sulphate ) . For further details contact BARC, Trombay.
2 The main entrance door of the examination room to be lead lined with 0.5 mm lead sheet.
NOTE : For installation with Image Intensifier the minimum clearance required is 9 feet
( 2740 mm )
4 A trench with dimension 3 inches wide X 4 inches deep ( 75 mm X 100 mm ) covered with
seasoned wood , having cross section of 0.5 inch X 6 inches ( 13 mm X 150 mm ) , flushed to the
floor , is to be provided at location O - P as shown in the model layout plan .
5 For Fluoroscopic applications with fluorescent screen , the X - ray room windows , door and any
other openings will have to be made light leakage proof .
6 For Image Intensifier Installation , additional seasoned wooden beam of size 6 inches X 2.5
inches ( 150 mm X 65 mm ) to be fixed at a minimum height with clearance of 9 feet ( 2740 mm
) from finished floor , at location M - N as shown in the model layout plan.
7 Dark room with standard accessories to be provided before electrical installation of the
equipment. Guidelines should be obtained from the manufactures / Suppliers of the Dark room
accessories.
RADIATION SAFETY
• Lead lined Screen to be provided in front of the X - ray control for the safety of the operator.
• Radiation safety measures to be adhered to (e.g. use of lead aprons and other radiation
protection measures) as per Atomic Energy Regulatory Board regulations for the safety of
patients and operator.
010-4 Pg. 1 / 2
Siemens Ltd.
Copyright © SIEMENS LTD. INDIA. All rights reserved.
The information in this CD is not a controlled document and to be used only for reference.
Before ordering any parts HO-Med-CS-SP to be contacted for obtaining the latest information.
Back
S KLINOSKOP H
Pre - Installation
A Mains power supply to be provided and terminated in the Main Switch at a Height of 5 feet
(1270 mm) from finished floor, at the location (1), as shown in the model layout plan.
B Double earthing to be provided and terminated in copper strip below the main switch.
E A radiation warning lamp to be installed above the entrance of the X - ray room door at the
location (4), as shown in the model layout plan.
F For three phase mains supply , where static balancer is used , wiring from mains contactor
(2) to the static balancer (5) is to be provided.
G In case of Image Intensifier installation, a servo controlled voltage stabilizer of, 240 V, 50 Hz,
1 KVA Capacity will have to be provided.
CAUTION
• All items from (1) to (9) will have to be interconnected with the earth wire terminating in the
copper strip with proper size of copper wire.
• The power supply to the X - ray room is to be drawn by the shortest possible route from the
main distribution transformer or the main source of power supply located in the Hospital /
Clinic.
• In case the line resistance exceeds the rated value required to give full output of the X - ray
generator, the output of the X - ray generator will have to be de - rated.
010-4 Pg. 2 / 2
Siemens Ltd.
Copyright © SIEMENS LTD. INDIA. All rights reserved.
The information in this CD is not a controlled document and to be used only for reference.
Before ordering any parts HO-Med-CS-SP to be contacted for obtaining the latest information.
Back
S KLINOSKOP H
Installation
KLINOSKOP H
MED
Siemens Ltd.
Copyright © SIEMENS LTD. INDIA. All rights reserved.
The information in this CD is not a controlled document and to be used only for reference.
Before ordering any parts HO-Med-CS-SP to be contacted for obtaining the latest information.
Back
S KLINOSKOP H
Installation
List of Pages
020 - 8 Adjustments
020 -1 Pg 1/1
Siemens Ltd.
Copyright © SIEMENS LTD. INDIA. All rights reserved.
The information in this CD is not a controlled document and to be used only for reference.
Before ordering any parts HO-Med-CS-SP to be contacted for obtaining the latest information.
Back
S KLINOSKOP H
Installation
Safety Instructions
General Safety Instructions
Before proceeding with the installation, make sure that mains voltage and frequency specified
are available. Check availability of the pre - filtration on the X - Ray tube assembly. Remove
packing materials and protective grease residue from all parts before assembling. Apply thin
film of oil on to rails .Re - install all the mounting bolts / screws as soon as possible during
installation to prevent later mix - up (This does not apply to the bolts of transport packing.)
General Recommendations
1 During Radiography, the operator should stand behind a protective screen and as far
away as possible (not less than 2 Meters) from the X ray tube head and the patient.
2 The X ray beam should be properly confined by the use of collimating devices and cones.
This also improves the picture quality. During fluoroscopy, the X ray beam should be
confined to the limits of the fluoroscopic screen protected by lead glass.
3 During Fluoroscopy, the operator should wear protective clothing, e.g. lead apron,
protective gloves. The protective ray guard provided should be mounted on the spot film
device
NOTE
020 -2 Pg. 1 / 2
Siemens Ltd.
Copyright © SIEMENS LTD. INDIA. All rights reserved.
The information in this CD is not a controlled document and to be used only for reference.
Before ordering any parts HO-Med-CS-SP to be contacted for obtaining the latest information.
Back
S KLINOSKOP H
Installation
Safety Notes
To ensure the safety of the patient and the operator, the equipment must be checked regularly
to maintain its reliability and serviceability. More frequent checks are required if the equipment
is operated under unusual conditions.
Before using the equipment for examinations, the user must ascertain that all the safety related
devices are functioning properly and that the unit is ready for operation. Special attention must
be given to the displays and pilot lights (Visual Checks). Normally during radiography/
fluoroscopy the radiation / H. T. ‘ON ‘Warning indication lamp lights up. In case of
malfunctioning of the control component, the warning lamp may continue to glow. In such case,
the complete unit must be switched ‘OFF’ and the concerned service department should be
informed for fault correction.
As manufacturers of electro medical products, the safety related performance of the equipment
is strictly maintained. The repairs, modifications and maintenance are carried out only by us.
For this purpose the replacement parts, as and when required are changed with the original
components only.
020 -2 Pg. 2 / 2
Siemens Ltd.
Copyright © SIEMENS LTD. INDIA. All rights reserved.
The information in this CD is not a controlled document and to be used only for reference.
Before ordering any parts HO-Med-CS-SP to be contacted for obtaining the latest information.
Back
S KLINOSKOP H
Installation
Make sure that all protective - ground wires provided by the manufacturer are connected properly
before starting the equipment after installation. In case of a fault, they must always be connected
to the protective - ground wire. To ensure this, the connection between these covers and the
protective ground wire must be made with screws and lock washers, or via the protective ground
wires provided. This applies for example to all metallic covers which may develop a dangerous
contact voltage in the protective ground wire between the different components of the equipment
and the main supply must be connected according to the wiring diagram. After completion of the
operation, the protective ground wires must be tested with the Multimeter.
Body Protectors :
It is mandatory to use the appropriate body protectors.
Radiation Protection :
The safety instructions described concerning radiation protection must be observed during
adjustment and start - up procedures for X - ray systems.
Mandatory Reporting :
The engineering supervisor in charge must be informed at once if there has been an accident or if
there are any hazards which may cause an accident. Make sure that the ground connection is
correct. The protective conductor shall be connected to the ground terminal of the generator as
indicated in the wiring diagram. At the end of the installation, these ground connections shall be
checked again.
020 -3 Pg. 1 / 1
Siemens Ltd.
Copyright © SIEMENS LTD. INDIA. All rights reserved.
The information in this CD is not a controlled document and to be used only for reference.
Before ordering any parts HO-Med-CS-SP to be contacted for obtaining the latest information.
Back
S KLINOSKOP H
Installation
Case I
Dim. - 2100 mm X 1020 mm X 1075 mm
Approx. Net Wt. 315 Kg. Approx. Gross Wt. 450 Kg.
Klinoskop H Table + Bucky with Bucky Grid + Cassette Tray , Single tube telecoupling
Gear Box Assembly ( Motor + Gear Box ) , Foot rest, Cough guard , Ray guard ,
Compression cone , Diaphragm plate, Patient Hand Grips, Ring nuts ,Straight cuff , Cone
12 cms, Motorised Collimator with connecting cable, Foot switch , Immobilizing device, Base
marking template , Guide rod, Interface cable, Packet of Fastener ,Operating Manual
Case II
Dim. - 1150 mm X 650 mm X 300 mm
Approx. Net Wt. 45 Kg. Approx. Gross Wt. 70 Kg.
Explorator H with cable & Screen Grid
Case III
Dim. - 1150 mm X 1000 mm X 650 mm
Approx. Net Wt. 70 Kg. Approx. Gross Wt. 118 Kg.
L - Carriage with compression carriage
Case IV
Dim. - 725 mm X 260 mm X 175 mm
Approx. Net Wt. 80 Kg. Approx. Gross Wt. 100 Kg.
Counter weights
Case V
Dim. - 685 mm X 260 mm X 175 mm
Approx. Net Wt. 70 Kg. Approx. Gross Wt. 85 Kg.
Counter weights
020 - 4 Pg. 1 / 2
Siemens Ltd.
Copyright © SIEMENS LTD. INDIA. All rights reserved.
The information in this CD is not a controlled document and to be used only for reference.
Before ordering any parts HO-Med-CS-SP to be contacted for obtaining the latest information.
Back
S KLINOSKOP H
Installation
2 * Check List of Column Stand Components
Case I
Dim. - 6150 mm X 425 mm X 450 mm
Column Stand
Cross Arm Tube
Column Extension Assembly
Floor Rail
Ceiling Rail
Extension Floor Rail
Extension Ceiling Rail
Case II
Dim. - 1100 mm X 775 mm X 550 mm
Column Base
Cross Carriage
Set of Scales
Column Carriage Cover
Cable Holder
Cable Clamp
Flat Piece
Handle for column Carriage
Handle for cross Arm
Counterweights
Packet of Fasteners
020 - 4 Pg. 2 / 2
Siemens Ltd.
Copyright © SIEMENS LTD. INDIA. All rights reserved.
The information in this CD is not a controlled document and to be used only for reference.
Before ordering any parts HO-Med-CS-SP to be contacted for obtaining the latest information.
Back
S KLINOSKOP H
Installation
Preparation Of Site
Check the availability of required power supply. Plan lay out by referring pre - installation
instructions. In Accordance with the dimensional drawing and project drawing, establish the
orientation point and central line of table. Do the marking on the floor.
Preparation Of Installation
1 * Take all packed casings in a room nearer to area, where they are going to be installed.
2 * Open all COLUMN Cases and check the received parts are as per check list, given in
020 - 4 Pg. 2 / 2.
3 * Mark the positions of horizontal beam, Ceiling rail & flooring rail. Drill the holes
accordingly and fix them with given fasteners (Refer Dimensional & Project drawing).
4 * Install Column stand (Installation of Column stand is not given in this manual
descriptively. )
Only take out cardboard packs. Check all material is as per check list given in document
020 - 4 Pg. 1 / 2
6 * Align the Foundation template and mark holes in the floor. Drill the fixing holes. Grout
the foundation bolts supplied along with the unit
NOTE
020 - 5 Pg 1 / 1
Siemens Ltd.
Copyright © SIEMENS LTD. INDIA. All rights reserved.
The information in this CD is not a controlled document and to be used only for reference.
Before ordering any parts HO-Med-CS-SP to be contacted for obtaining the latest information.
Back
S KLINOSKOP H
Installation
S9 S9- 91, 92
020 - 6 Pg. 1 / 12
Siemens Ltd.
Copyright © SIEMENS LTD. INDIA. All rights reserved.
The information in this CD is not a controlled document and to be used only for reference.
Before ordering any parts HO-Med-CS-SP to be contacted for obtaining the latest information.
Back
S KLINOSKOP H
Installation
2 * Installation of Horizontal Carriage Assembly
NOTE
8
Do not unscrew the transport protector (7 fig.
10 6) provided to hold compression carriage (8 fig.
3) on transverse carriage (9 fig. 3). Temporarily
unscrew the stopper (10 fig. 3) from L - Carriage
assembly.
Fig. 3
Fig. 4
Fig. 5 Fig. 6
020-6 Pg. 2 / 12
Siemens Ltd.
Copyright © SIEMENS LTD. INDIA. All rights reserved.
The information in this CD is not a controlled document and to be used only for reference.
Before ordering any parts HO-Med-CS-SP to be contacted for obtaining the latest information.
Back
S KLINOSKOP H
Installation
3 * Installation of Counter-weights
13
Fig. 7
Fig. 8
020 - 6 Pg. 3 / 12
Siemens Ltd.
Copyright © SIEMENS LTD. INDIA. All rights reserved.
The information in this CD is not a controlled document and to be used only for reference.
Before ordering any parts HO-Med-CS-SP to be contacted for obtaining the latest information.
Back
S KLINOSKOP H
Installation
4 * Installation of Spot Film Device
NOTE
15
Watch out for switch S35 (17 Fig. 9) while
14 inserting the spot film unit into the compression
carriage (In received condition you may find tape
Fig. 9 on S35 switch). Don’t remove tape from this
switch at this point of time. Slide the spot film unit
as shown in (fig. 11) across the table top
and in the direction of arrow ( Guide the rails
between the ball-bearings ) into the compression
carriage unit until fully engaged . Screw the stop
bolt (14 fig. 9) into the spot film unit guide rail
again. Remove tape from S35 switch. Unscrew the
transport protector from L - Carriage
( Compression carriage is hold to L - Carriage
16 by transport protector ) . Screw the spacer tube
back again. This serves as a stop for the
compression carriage
Fig. 10
Siemens Ltd.
Copyright © SIEMENS LTD. INDIA. All rights reserved.
The information in this CD is not a controlled document and to be used only for reference.
Before ordering any parts HO-Med-CS-SP to be contacted for obtaining the latest information.
Back
S KLINOSKOP H
Installation
Fig. 12
Fig. 13 Fig. 14
020 - 6 Pg. 5 / 12
Siemens Ltd.
Copyright © SIEMENS LTD. INDIA. All rights reserved.
The information in this CD is not a controlled document and to be used only for reference.
Before ordering any parts HO-Med-CS-SP to be contacted for obtaining the latest information.
Back
S KLINOSKOP H
Installation
6 * Installation of Counter-weights for
compression carriage & spot film unit
Fig. 15
Check balancing of compression carriage along with spot film (Including Cassette) by moving it up or
down. After leaving Explorator (Spot film unit) at particular position it should remain in same position
after removing your hand. Then it is called as perfect balancing.
3* L - Carriage Installation.
7* L - Carriage Balancing.
Fix previously removed table top; profile rail with spacer strips
020 - 6 Pg. 6 / 12
Siemens Ltd.
Copyright © SIEMENS LTD. INDIA. All rights reserved.
The information in this CD is not a controlled document and to be used only for reference.
Before ordering any parts HO-Med-CS-SP to be contacted for obtaining the latest information.
Back
S KLINOSKOP H
Installation
7 * Installation of Electrical Connections
Routing of Explorator Interface Cable
Fig. 16
21
19
22
20
Fig. 18
Fig. 17
020 - 6 Pg. 7 / 12
Siemens Ltd.
Copyright © SIEMENS LTD. INDIA. All rights reserved.
The information in this CD is not a controlled document and to be used only for reference.
Before ordering any parts HO-Med-CS-SP to be contacted for obtaining the latest information.
Back
S KLINOSKOP H
Installation
Remove Compression Carriage cover as shown in
23 (23 Fig. 19). Remove vertical Carriage cover as
shown in (24 Fig. 20). Intra - carriage cable is
already routed on L - Carriage assembly. Connect
connector X 24 of Explorator interface cable to
intra - carriage cable connector X 25 (25 Fig. 21).
Connect other end of intra - carriage cable to
longitudinal & transverse brake assembly
(26 Fig. 22). Insert Hose in leg cover in such a
way that groove of hose flange will fit in leg cover
Fig. 19 wall as shown in Fig. 23
25
24
Fig. 20 Fig. 21
26
Fig. 22 Fig. 23
020 - 6 Pg. 8 / 12
Siemens Ltd.
Copyright © SIEMENS LTD. INDIA. All rights reserved.
The information in this CD is not a controlled document and to be used only for reference.
Before ordering any parts HO-Med-CS-SP to be contacted for obtaining the latest information.
Back
S KLINOSKOP H
Installation
Interconnections of External Interface Cables
Install foot switch by connecting foot switch flying leads to a provided socket
( A part of cable routed from Explorator, 2 way socket ) X 15
Sr. No. Type of External Cable Where to connect on Power Supply &
Distribution Pcb Assembly
1 Collimator Cable X5
8 Core , Multicore Grey
020 - 6 Pg. 9 / 12
Siemens Ltd.
Copyright © SIEMENS LTD. INDIA. All rights reserved.
The information in this CD is not a controlled document and to be used only for reference.
Before ordering any parts HO-Med-CS-SP to be contacted for obtaining the latest information.
Back
S KLINOSKOP H
Installation
Keep the foot rest (27 Fig. 24) into the place;
press the two handgrips (28 Fig. 24) upwards so
that the foot engages in the groove of the profile
rail notches. Pressing the handgrips upwards
releases the locking mechanism; the footrest can
be placed to any desired position.
27 28
Fig. 24
020 - 6 Pg. 10 / 12
Siemens Ltd.
Copyright © SIEMENS LTD. INDIA. All rights reserved.
The information in this CD is not a controlled document and to be used only for reference.
Before ordering any parts HO-Med-CS-SP to be contacted for obtaining the latest information.
Back
S KLINOSKOP H
Installation
8 * Explorator H Manual Spot film Device
10
1
2
3
4
5
6
7 9
Fig. 25
Operating Controls
020 - 6 Pg. 11 / 12
Siemens Ltd.
Copyright © SIEMENS LTD. INDIA. All rights reserved.
The information in this CD is not a controlled document and to be used only for reference.
Before ordering any parts HO-Med-CS-SP to be contacted for obtaining the latest information.
Back
S KLINOSKOP H
Installation
Fig. 26
Installing Motorised Double slot Collimator :
020 - 6 Pg. 12 / 12
Siemens Ltd.
Copyright © SIEMENS LTD. INDIA. All rights reserved.
The information in this CD is not a controlled document and to be used only for reference.
Before ordering any parts HO-Med-CS-SP to be contacted for obtaining the latest information.
Back
S KLINOSKOP H
Installation
Start Up Instructions
1* Before connecting table to available power supply, check carefully for any loose
connections. Refer wiring and circuit diagrams provided in 4 W 5245.
2* Check the position of MCB on leg tilt assembly. It should be in OFF position.
(Lever should be Downwards )
3* Check positions of Explorator switches. Switches which are mounted horizontally
operating lever should be on left side. Room light switch operating lever should be
on upper side.
4* Check whether collimator and Bucky are interfaced or not. If not then connect
them.
5* Check the incoming power supply by Multimeter. It should be in the limit of
( 415 Vac + 10 % - 15 % )
6* Connect Input supply cable, where phase sequence is clearly indicated. To be on
safer side, check resistance between Phases to Neutral & Phase to Ground. It
should be in Mega - ohms.
7* Switch on the power supply. Check availability of supply at MCB Input.
020 - 7 Pg. 1 / 1
Siemens Ltd.
Copyright © SIEMENS LTD. INDIA. All rights reserved.
The information in this CD is not a controlled document and to be used only for reference.
Before ordering any parts HO-Med-CS-SP to be contacted for obtaining the latest information.
Back
S KLINOSKOP H
Installation
Adjustment Instructions
Adjustment of Limit Switches
If the adjustment is done properly at the time of installing Gear box assembly then following
adjustments are not needed.
Counter - Weight balancing must be accurately carried out with all the accessories like lead
guard, Cough guard & Compression cone.
May be fine adjustments are required because safety switch position depends upon the Gear
Box Installation position.
Go to particular position either Horizontal or Vertical and check whether tilting stops at that
position If not then loose respective actuators provided on segment such that they will press the
plunger of safety switch in turn stops the movement.
020 - 8 Pg. 1 / 3
Siemens Ltd.
Copyright © SIEMENS LTD. INDIA. All rights reserved.
The information in this CD is not a controlled document and to be used only for reference.
Before ordering any parts HO-Med-CS-SP to be contacted for obtaining the latest information.
Back
S KLINOSKOP H
Installation
Caution
When working with X - rays, protective clothing must be worn. No parts of the body must
enter the radiation zone. Radiation must be switched off when making mechanical
adjustment.
Fig . 29
020 - 8 Pg. 2 / 3
Siemens Ltd.
Copyright © SIEMENS LTD. INDIA. All rights reserved.
The information in this CD is not a controlled document and to be used only for reference.
Before ordering any parts HO-Med-CS-SP to be contacted for obtaining the latest information.
Back
S KLINOSKOP H
Installation
Vertical Direction
Fig. 30
Horizontal Direction
Switch on radiation, compress the spot film unit and collimate horizontally about 1 cm with the
collimator. Mark the center of collimation on the fluorescent screen with the spot film unit de-
compressed. Now operate compression & then ascertain displacement and mark once more.
Adjust the displacement to a minimum by tilting the X - Ray tube assembly. Ascertain the shift
of the central ray be compressing and de - compressing several times. See fig. 30.
Carry out centering of the central ray to the center of the spot film unit using the support.
Check the central ray adjustment in the 0 ° , 90 ° and 12 ° positions of the table top and center
where necessary.
020 - 8 Pg. 3 / 3
Siemens Ltd.
Copyright © SIEMENS LTD. INDIA. All rights reserved.
The information in this CD is not a controlled document and to be used only for reference.
Before ordering any parts HO-Med-CS-SP to be contacted for obtaining the latest information.
Back
S KLINOSKOP H
Circuit Diagram
KLINOSKOP H
MED
Siemens Ltd.
Copyright © SIEMENS LTD. INDIA. All rights reserved.
The information in this CD is not a controlled document and to be used only for reference.
Before ordering any parts HO-Med-CS-SP to be contacted for obtaining the latest information.
Back
S KLINOSKOP H
Circuit Diagram
List of Pages
030 - 3 Brakes
030 - 5 Collimator
030 -1 Pg. 1 / 1
Siemens Ltd.
Copyright © SIEMENS LTD. INDIA. All rights reserved.
The information in this CD is not a controlled document and to be used only for reference.
Before ordering any parts HO-Med-CS-SP to be contacted for obtaining the latest information.
Back
S KLINOSKOP H
Circuit Diagram
030 -2 Pg. 1 / 1
Siemens Ltd.
Copyright © SIEMENS LTD. INDIA. All rights reserved.
The information in this CD is not a controlled document and to be used only for reference.
Before ordering any parts HO-Med-CS-SP to be contacted for obtaining the latest information.
Back
S KLINOSKOP H
Circuit Diagram
030 -3 Pg. 1 / 1
Siemens Ltd.
Copyright © SIEMENS LTD. INDIA. All rights reserved.
The information in this CD is not a controlled document and to be used only for reference.
Before ordering any parts HO-Med-CS-SP to be contacted for obtaining the latest information.
Back
S KLINOSKOP H
Circuit Diagram
030 -4 Pg. 1 / 1
Siemens Ltd.
Copyright © SIEMENS LTD. INDIA. All rights reserved.
The information in this CD is not a controlled document and to be used only for reference.
Before ordering any parts HO-Med-CS-SP to be contacted for obtaining the latest information.
Back
S KLINOSKOP H
Circuit Diagram
030 -5 Pg. 1 / 1
Siemens Ltd.
Copyright © SIEMENS LTD. INDIA. All rights reserved.
The information in this CD is not a controlled document and to be used only for reference.
Before ordering any parts HO-Med-CS-SP to be contacted for obtaining the latest information.
Back
S KLINOSKOP H
Circuit Diagram
030 -6 Pg. 1 / 1
Siemens Ltd.
Copyright © SIEMENS LTD. INDIA. All rights reserved.
The information in this CD is not a controlled document and to be used only for reference.
Before ordering any parts HO-Med-CS-SP to be contacted for obtaining the latest information.
Back
S KLINOSKOP H
Circuit Diagram
030 -7 Pg. 1 / 1
Siemens Ltd.
Copyright © SIEMENS LTD. INDIA. All rights reserved.
The information in this CD is not a controlled document and to be used only for reference.
Before ordering any parts HO-Med-CS-SP to be contacted for obtaining the latest information.
Back
S KLINOSKOP H
Circuit Diagram
030 -8 Pg. 1 / 1
Siemens Ltd.
Copyright © SIEMENS LTD. INDIA. All rights reserved.
The information in this CD is not a controlled document and to be used only for reference.
Before ordering any parts HO-Med-CS-SP to be contacted for obtaining the latest information.
Back
S KLINOSKOP H
Circuit Description
KLINOSKOP H
MED
Siemens Ltd.
Copyright © SIEMENS LTD. INDIA. All rights reserved.
The information in this CD is not a controlled document and to be used only for reference.
Before ordering any parts HO-Med-CS-SP to be contacted for obtaining the latest information.
Back
S KLINOSKOP H
Circuit Description
List of Pages
040 -1 Pg. 1 / 1
Siemens Ltd.
Copyright © SIEMENS LTD. INDIA. All rights reserved.
The information in this CD is not a controlled document and to be used only for reference.
Before ordering any parts HO-Med-CS-SP to be contacted for obtaining the latest information.
Back
S KLINOSKOP H
Circuit Description
Component Review:
0 V - X 1. 8
17 V - X 1. 7
21 V - X 1. 6
28 V - X 1. 5
040 - 2 Pg. 1 / 1
Siemens Ltd.
Copyright © SIEMENS LTD. INDIA. All rights reserved.
The information in this CD is not a controlled document and to be used only for reference.
Before ordering any parts HO-Med-CS-SP to be contacted for obtaining the latest information.
Back
S KLINOSKOP H
Circuit Description
Component Review:
Current Flow:
(I) Stand - by Condition
26 V ⇒ X6.1 ⇒ R1 ⇒ X25.3 ⇒ X24.3 ⇒ X14.3 ⇒ br3,br4,br5 ⇒ X14.5 ⇒ X24.5 ⇒ X25.5
⇑ ⇓
⇒ X6.6 ⇒ X2.Z14 O V ⇐ X2 . b16
⇓ ⇑
⇒ X13.3 ⇒ X25.2 ⇒ X24.2 ⇒ br1 , br2 ⇒ X13.5 ⇒ X24.4 ⇒ X25.4
(II) When S 14 (NO) is Operated
26 V ⇒ X2.z2 ⇒ X21.4 ⇒ X12.4 ⇒ X21.2 ⇒ X12.2 ⇒ X2.b12 ⇒ X6.13 ⇒ X6.9 ⇒ X2.z12
⇒ X25.1 ⇒ X24.1 ⇒ X13.1 ⇒ br1 ⇒ X13.5 ⇒ X24.4 ⇒ X25.4 ⇒ X2 . b16 ⇒ O V
040 - 3 Pg. 1 / 1
Siemens Ltd.
Copyright © SIEMENS LTD. INDIA. All rights reserved.
The information in this CD is not a controlled document and to be used only for reference.
Before ordering any parts HO-Med-CS-SP to be contacted for obtaining the latest information.
Back
S KLINOSKOP H
Circuit Description
When the switch is moved right i.e. to operate S 18 a (NO) is actuated and contactor S a is
switched ON which causes the motor to run in one direction and the table steadily rises to the
vertical position.
When the table reaches vertical position, the cam actuates switch S9, thus interrupts the supply to
contactor Sa and the table stops in the vertical position.
To acquire any intermediate position the switch on the control arm should be released when
desired position of the table is attained.
When the switch is moved left, i.e. to actuate S18u, the switch S 18u (NO) operates and contactor
Su is switched ON which causes the motor to rotate in the opposite direction i.e. horizontal and the
table steadily lowers down to the horizontal position and stops in this position when the switch S 11
is actuated by the cam and the supply to Su is interrupted.
040 - 4 Pg. 1 / 2
Siemens Ltd.
Copyright © SIEMENS LTD. INDIA. All rights reserved.
The information in this CD is not a controlled document and to be used only for reference.
Before ordering any parts HO-Med-CS-SP to be contacted for obtaining the latest information.
Back
S KLINOSKOP H
Circuit Description
28 V ac ⇒ X20.9 ⇒ X11.9 ⇒ X11.7 ⇒ X20.7 ⇒ X2.b4 ⇒ X6.4 ⇒ X2.z4 ⇒Sa.21
When the horizontal position is reached the micro switch S11 opens and the table now stops in this
position.
To acquire any intermediate position, the switch on the control arm should be released when the
desired position of the table is attained.
This position is meant to further lower the table by 12 ° w.r.t. the horizontal position. This is
achieved by operating the switch on the control arm.
The micro switch S11 opens on reaching the horizontal position .When S 18 is operated again
rectifier V 21 energizes the relay hr5.
When the hr5 relay is energized, it switches ON the transistor V11 and thus relay hr3 is ON. When
the hr3 relay is ON, contactor hr4 is also ON and the circuit is completed as below.
The table is now further lowered (w.r.t. the horizontal position) until the cam operates the switch S
10 (NC) and the table stops in this position i.e. is the trendelenburg position. The cam is so
adjusted that the table can be lowered only up to 12 ° below the horizontal position.
040 - 4 Pg. 2 / 2
Siemens Ltd.
Copyright © SIEMENS LTD. INDIA. All rights reserved.
The information in this CD is not a controlled document and to be used only for reference.
Before ordering any parts HO-Med-CS-SP to be contacted for obtaining the latest information.
Back
S KLINOSKOP H
Circuit Description
040 - 5 Pg. 1 / 1
Siemens Ltd.
Copyright © SIEMENS LTD. INDIA. All rights reserved.
The information in this CD is not a controlled document and to be used only for reference.
Before ordering any parts HO-Med-CS-SP to be contacted for obtaining the latest information.
Back
S KLINOSKOP H
Circuit Description
Fluoroscopy
Exposure Release
When the cassette is moved in the exposure area, a micro switch S 17 is actuated, thus operating
the relay hr 1. Compression and transverse brakes are operated. 24 V / 220 V is sent out to control
through X3 / 12 for generator preparation. 24 V / 220 V generator ready signal is available through
X 3 / 3. Exposure is initiated by pressing the push - button switch S 22.
26 V ⇒ S 35 ⇒ S 17 ( NO ) ⇒ hr1 ( NO )
N1.22 ⇒ X3.2 ⇒ hr2 ( NO ) ⇒ X3.12 ⇒ N1.47 ⇒ To preparation circuit of control.
V22 ON brings bb relay into circuit which starts Bucky motor and S 1 brings ab relay which
switches ON the timer and hence AS and exposure takes place.
040 - 6 Pg 1 / 1
Siemens Ltd.
Copyright © SIEMENS LTD. INDIA. All rights reserved.
The information in this CD is not a controlled document and to be used only for reference.
Before ordering any parts HO-Med-CS-SP to be contacted for obtaining the latest information.
Back
S KLINOSKOP H
Circuit Description
This circuit monitors all the three incoming phases on the unit and disables the table movements
(Table tilting) if the phase sequence fails.
Phase ‘U ‘is used to generate 12 V Dc for the circuit. Phase ‘V ‘is isolated and converted into
square wave by J 1. Differentiated by R 5 and C 1. Phase ‘W ‘is also isolated and converted into
square wave by J 2.
The output of J3.15 and J3.16 is ored and then integrated to drive the interlocking relay K1. As
long as phase sequence is correct J3.15 goes periodically high and keeps K1 ON.
If any of the phases sequence fails. J3.15 remains low for all the time, thus K1 drops, which in turn
cut the control supply of motor contactors. The fault condition is indicated by red LED V3. A
normally closed contact of K1 is used to light the red lamp externally visible on the table.
040 - 7 Pg 1 / 1
Siemens Ltd.
Copyright © SIEMENS LTD. INDIA. All rights reserved.
The information in this CD is not a controlled document and to be used only for reference.
Before ordering any parts HO-Med-CS-SP to be contacted for obtaining the latest information.
Back
S KLINOSKOP H
KLINOSKOP H
MED
Siemens Ltd.
Copyright © SIEMENS LTD. INDIA. All rights reserved.
The information in this CD is not a controlled document and to be used only for reference.
Before ordering any parts HO-Med-CS-SP to be contacted for obtaining the latest information.
Back
S KLINOSKOP H
Service
Supply Problem
No
No Change position of
Yes
Is F10 Fuse on D9 Replace MCB
MCB & Check
Blown
No No
Is 26 V dc Voltage
Is F7 Fuse on D9 Is 21V ac present at
across capacitor C1 on No Yes Yes Replace D9 PCB
PCB O.K. X1.6 on D9 PCB
D1 on D9 PCB
No Replace F7 Fuse
Siemens Ltd.
Copyright © SIEMENS LTD. INDIA. All rights reserved.
The information in this CD is not a controlled document and to be used only for reference.
Before ordering any parts HO-Med-CS-SP to be contacted for obtaining the latest information.
Back
S KLINOSKOP H
Service
Yes
Is Voltage 26 V dc
Refer previous page of trouble
present across capacitor C1 on No
shooting
D9 PCB
Yes
Yes
Is Mechanical adjustment /
Yes Replace respective Brakes
Fitting of brakes are O. K.
No
Do the adjustment of
brakes and Check
Again
050 -2 Pg. 2 / 5
Siemens Ltd.
Copyright © SIEMENS LTD. INDIA. All rights reserved.
The information in this CD is not a controlled document and to be used only for reference.
Before ordering any parts HO-Med-CS-SP to be contacted for obtaining the latest information.
Back
S KLINOSKOP H
Service
Yes
Yes
Yes
Yes
Yes
Siemens Ltd.
Copyright © SIEMENS LTD. INDIA. All rights reserved.
The information in this CD is not a controlled document and to be used only for reference.
Before ordering any parts HO-Med-CS-SP to be contacted for obtaining the latest information.
Back
S KLINOSKOP H
Service
Yes
Yes
Yes Yes
Make mech.
Is Fuse F6 O.K. No Replace F6 Fuse Is Joystick lever operating No adjustment to
micro-switches of Joy ensure actuation
stick
Yes
Yes
Is W.W. Resistor
No Replace R5
R 5 O.K. Are Capacitors C1 , Replace Defective
No
C2 of Collimator Capacitors
O.K.
Yes
Yes
Replace defective
Is Collimator Bulb Is Collimator motor No
No Replace the Bulb motor
O.K. O.K.
050 - 2 Pg. 4 / 5
Siemens Ltd.
Copyright © SIEMENS LTD. INDIA. All rights reserved.
The information in this CD is not a controlled document and to be used only for reference.
Before ordering any parts HO-Med-CS-SP to be contacted for obtaining the latest information.
Back
S KLINOSKOP H
Service
Yes
Yes
Replace S 35 Switch
Make the
Is Tube coupling switch
No Is connection to S 26 No connection &
S 26 in closed condition
is made Check again
Yes
Is preparation
Is cassette inserted in Check contacts should
yes Switch S17 in Yes Yes Replace S17 Switch
explorator frame be open in pressed
closed condition
condition
No
Insert cassette frame in If problem persists check generator Interface cable &
radiation field Connections at generator side .
Siemens Ltd.
Copyright © SIEMENS LTD. INDIA. All rights reserved.
The information in this CD is not a controlled document and to be used only for reference.
Before ordering any parts HO-Med-CS-SP to be contacted for obtaining the latest information.
Back
S KLINOSKOP H
Spare Parts
KLINOSKOP H
MED
Siemens Ltd.
Copyright © SIEMENS LTD. INDIA. All rights reserved.
The information in this CD is not a controlled document and to be used only for reference.
Before ordering any parts HO-Med-CS-SP to be contacted for obtaining the latest information.
Back
S KLINOSKOP H
Spare Parts
List of Pages
060 - 1 Pg. 1 / 1
Siemens Ltd.
Copyright © SIEMENS LTD. INDIA. All rights reserved.
The information in this CD is not a controlled document and to be used only for reference.
Before ordering any parts HO-Med-CS-SP to be contacted for obtaining the latest information.
Back
S KLINOSKOP H
Spare Parts
Siemens Ltd.
Copyright © SIEMENS LTD. INDIA. All rights reserved.
The information in this CD is not a controlled document and to be used only for reference.
Before ordering any parts HO-Med-CS-SP to be contacted for obtaining the latest information.
Back
S KLINOSKOP H
Spare Parts
7 6 5 4
060 - 2 Pg. 2 / 6
Siemens Ltd.
Copyright © SIEMENS LTD. INDIA. All rights reserved.
The information in this CD is not a controlled document and to be used only for reference.
Before ordering any parts HO-Med-CS-SP to be contacted for obtaining the latest information.
Back
S KLINOSKOP H
Spare Parts
060 - 2 Pg. 3 / 6
Siemens Ltd.
Copyright © SIEMENS LTD. INDIA. All rights reserved.
The information in this CD is not a controlled document and to be used only for reference.
Before ordering any parts HO-Med-CS-SP to be contacted for obtaining the latest information.
Back
S KLINOSKOP H
Spare Parts
3 1 6 4 5 7
060 - 2 Pg. 4 / 6
Siemens Ltd.
Copyright © SIEMENS LTD. INDIA. All rights reserved.
The information in this CD is not a controlled document and to be used only for reference.
Before ordering any parts HO-Med-CS-SP to be contacted for obtaining the latest information.
Back
S KLINOSKOP H
Spare Parts
4
2
4
1
5 6 8
060 - 2 Pg. 5 / 6
Siemens Ltd.
Copyright © SIEMENS LTD. INDIA. All rights reserved.
The information in this CD is not a controlled document and to be used only for reference.
Before ordering any parts HO-Med-CS-SP to be contacted for obtaining the latest information.
Back
S KLINOSKOP H
Spare Parts
Miscellaneous
060 - 2 Pg. 6 / 6
Siemens Ltd.
Copyright © SIEMENS LTD. INDIA. All rights reserved.
The information in this CD is not a controlled document and to be used only for reference.
Before ordering any parts HO-Med-CS-SP to be contacted for obtaining the latest information.
Back